Rinnai Q205SN Guide d'installation

- Do not store or use gasoline or other ﬂ ammable vapors and

liquids in the vicinity of this or any other appliance.

- WHAT TO DO IF YOU SMELL GAS

- Do NOT try to light any appliance.

- Do NOT touch any electrical switch.

- Do NOT use any phone in your building.

- Immediately call your gas supplier from a neighbor’s phone.

Follow the gas supplier’s instructions.

- If you cannot reach your gas supplier, call the ﬁ re department.

8W.51.40.06 / 10.13 Changes reserved.

Installation & Servicing

Instructions

These instructions to be retained by user.

CAUTION!

Read this manual thoroughly before installing, servicing, putting

into operation or using this boiler and vent system.

WARNING!

Improper installation, adjustment, alteration, service or

maintenance can cause property damage, personal injury

(exposure of hazardous materials)* or loss of life. Refer to the

user's information manual provided with this boiler. Installation

and service must be performed by a licensed professional, service

agency or the gas supplier (who must read and follow the supplied

instructions before installing, servicing, or removing this boiler).

CAUTION!

The user manual is part of the documentation that is delivered

to the installation's operator. Go through the information in this

manual with the owner/operator and make sure that they are

familiar with all necessary operating instructions.

NOTICE!

Installation and service must be performed by a licensed

professional, service technician or the gas supplier.

Pictured: Q85SN, Q130SN

Q85SP, Q130SP

High efﬁ ciency condensing gas boiler

Q85SN/Q130SN/Q175SN/Q205SN/Q175CN

Q85SP/Q130SP/Q175SP/Q205SP/Q175CP

WARNING!

If you do not follow these instructions exactly, a ﬁ re or explosion

may result causing property damage, personal injury or loss of life.

Address: 103 International Drive, Peachtree City, GA, 30269

Toll-free: 1-800-621-9419 • Fax: 678-829-1666 • www.rinnai.us

Français: voir page 101

Installation & Servicing Instructions Rinnai Q-Series

2

Contents of instructions

These installation instructions contain important information for the safe installation, start-up and maintenance of

boilers with capacities 85,000 through 205,000 BTU/hr.

These installation instructions are intended for licensed professionals, who have the necessary knowledge and

are approved for working on heating and gas systems.

Subject to technical changes

Changes may be made without notice to the illustrations, process steps and technical data as a result of our policy

of continuous improvement.

Updating of documentation

Please contact us if you have any suggestions for improvements or corrections.

Find our contact details on the back of this manual.

Installation & Servicing Instructions Rinnai Q-Series

3

Content

1 Safety and general instructions ........................................................4

1.1 Designated use ...................................................................4

1.2 Hazard deﬁ nitions ................................................................4

1.3 Symbol deﬁ nitions ...............................................................4

1.4 The following instructions must be followed ........................5

1.5 Follow these instructions for the space heating water .........6

1.6 Tools, materials and additional equipment ..........................6

1.7 Relevant Installation, Service and User manuals ................6

1.8 Disposal ...........................................................................7

2 Regulations and guidelines ..............................................................7

3 Description of the boiler ...................................................................8

4 Packaging and transportation ..........................................................9

4.1 Scope of delivery .................................................................9

4.2 Transportation .....................................................................9

5 Installation .........................................................................10

5.1 Requirements for the installation room .............................10

5.2 Fitting the boiler .................................................................11

5.3 Dimensions ........................................................................12

5.3.1 Plumbing Kits.....................................................................15

5.3.2 Clearences from the boiler ................................................16

5.4 Technical speciﬁ cations .....................................................17

6 Connecting the boiler .....................................................................18

6.1 Central heating system ......................................................18

6.1.1 Plumbing Kits and installation ...........................................20

6.1.2 Side mounting kit for the Low Loss Header .......................24

6.1.3 Safety valve .......................................................................24

6.1.4 Low water cut off ...............................................................24

6.2 Boiler expansion tank ........................................................25

6.3 Underﬂ oor heating system (plastic pipes) ...........................25

6.4 Gas connection .................................................................26

6.5 Hot water supply (Combi boiler Q175CNQ175CP) ...........28

6.5.1 Domestic Water quality ......................................................28

6.5.2 Domestic water treatment Accessory ................................29

6.5.3 DHW Expansion Tank ........................................................29

6.5.4 Installing a valve kit ...........................................................29

6.5.5 Pressure relief Valve for Combi boilers .............................30

6.6 Condensate drain pipe ......................................................30

6.7 Vent system and air supply system ...................................31

6.7.1 Intake / Exhaust Guidelines ...............................................31

6.7.2a Examples vent and air supply systems (concentric) .........32

6.7.2b Examples vent and air supply systems (parallel) ..............33

6.7.3 Installation of the vent system ...........................................34

6.7.3.1 Boiler conversion from concentric to parallel ....................35

6.7.3.2 Installing air ﬁ lter ...............................................................35

6.7.4 Recommended vent/air intake terminal position ...............36

6.7.5 Direct vent closet and alcove installation ........................38

6.7.6 Dimensioning of the exhaust and air intake duct .............39

6.7.7 Combustion air and vent piping lengths. ...........................40

6.7.8 Calculation of compensation factor ...................................41

6.7.9 Room Air System (indoor combustion air) .........................42

7 External domestic hot water tanks .................................................45

8 Electrical connections ....................................................................45

9 Boiler controls .........................................................................49

9.1 Explanation of the function buttons ...................................50

10 Starting up: Filling and de-aerating the boiler and installation .......51

10.1 Requirements of the water system ....................................51

10.2 Filling the heating system ..................................................52

10.3 Hot water supply (only Q175C) .........................................53

11 Adjustments .........................................................................55

11.1 Altering adjustments ..........................................................55

11.2 Activating factory settings (green button function) ...........58

12 Isolating the boiler .........................................................................58

13 Commissioning .........................................................................59

13.1 Testing for gas leaks ..........................................................60

13.2 Testing the Ignition Safety shut off device .........................60

13.3 Checking the O

2

.................................................................61

13.4 Measuring the ionization current .......................................62

13.5 Installing the casing ...........................................................63

14 Maintenance .........................................................................63

14.1 Periodic examination of venting systems and boiler .........63

14.2 Inspection .........................................................................63

14.3 Maintenance activities .......................................................65

14.3.1 Reset service interval counter ...........................................67

14.4 Limited warranty ................................................................67

15 Parts of the boiler .........................................................................68

16 Blocks and Errors .........................................................................69

17 Spare parts .........................................................................77

18 Parts list vent system .....................................................................89

19 Common venting guidelines ...........................................................90

Appendix A - Outoor Reset Sensor Data .............................................91

Appendix B - Resistance table NTC sensors .......................................92

Installation & Servicing Instructions Rinnai Q-Series

4

1 Safety and general instructions

Please observe these instructions in the interest of your own safety.

1.1 Designated use

The boiler is designed for heating water for a central heating system and, if applicable,

generating domestic hot water. The boiler is delivered with a burner controller

(MCBA) pre-installed.The boiler can be ﬁ tted with a modulating outdoor reset sensor

ARV12 (included with the boiler) or an On/Off thermostat or relay panel end switch

(accessories).

1.2 Hazard deﬁ nitions

The following deﬁ ned terms are used throughout the documentation to bring attention

to the presence of hazards of various risk levels. Notices give important information

concerning the operation of the product.

DANGER:

Indicates the presence of hazards that will cause severe personal injury, death or

substantial property damage.

WARNING:

Indicates the presence of hazards that can cause severe personal injury, death or

substantial property damage.

CAUTION:

Indicates presence of hazards that will or can cause minor personal injury or property

damage.

CAUTION:

Risk of electric shock. Indicates presence of hazards due to electric shock.

NOTICE:

Indicates special instructions on installation, operation or maintenance that are

important but not related to personal injury or property damage.

1.3 Symbol deﬁ nitions

The following (safety) symbols may be encountered in these installation instructions

and on the unit:

This symbol indicates that the unit must be stored away from freezing conditions.

This symbol indicates that the packaging and/or contents can be damaged as

a result of insufﬁ cient care taken during transport.

This symbol indicates that, while still in its packaging, the unit must be protected

from weather conditions during transport and storage.

!

CAUTION

!

WARNING

NOTICE

i

!

DANGER

Installation & Servicing Instructions Rinnai Q-Series

5

1.4 The following instructions must be followed

- The boiler must only be used for its designated purpose, as described in the

Installation Instructions.

- Each unit is ﬁ tted with a data plate. Consult the details on this plate to verify whether

the boiler is compliant with its intended location, e.g.: gas type, power source and

venting classiﬁ cation.

-

Only use the boiler with the accessories and spare parts listed.

- Other combinations, accessories and consumables may only be used if they are

speciﬁ cally designed for the intended application and do not affect the system

performance and the safety requirements.

- Maintenance and repairs must be performed by a licensed professional.

- Installation of a condensing gas boiler must be reported to the relevant gas utility

company and have it approved.

- You are only allowed to operate the condensing gas boiler with the vent system

that has been speciﬁ cally designed and approved for this type of boiler.

- Please note that local permission for the vent system and the condensate water

connection to the public sewer system may be required.

You must also respect:

- The local building codes stipulating the installation rules.

- The local building codes concerning the air intake and outlet systems and the

chimney connection.

- The regulations for the power supply connection.

- The technical rules established by the gas utility company concerning the

connection of the gas connection to the local gas mains.

- The instructions and standards concerning the safety equipment for the water/

space heating system.

- The Installation Instructions for building heating systems.

- The boiler must be located in an area where leakage of the boiler or connections

will not result in damage to the area adjacent to the boiler or to lower ﬂ oors of

the structure. When such locations cannot be avoided, it is recommended that a

suitable drain pan be installed under the boiler.

- The boiler must be installed in such way that the all components are protected

from water (dripping, spraying, rain etc.) during boiler operation and service.

- The boiler must not be installed on or against carpeting.

- Do not restrict or seal any air intake or outlet openings.

- If you ﬁ nd any defects, you must inform the owner of the system of the defect and

the associated hazard in writing.

In failure to properly commission the boiler as described in section 13 may result

unreliable burner operation, reduced component life, and unsafe boiler operation.

DANGER. Gas is ﬂ ammable and may cause an explosion.

Beware if you smell gas: there may be an explosion hazard!

If the information in these instructions is not followed exactly, a ﬁ re or explosion may

result causing property damage, personal injury or death.

- Do not store or use gasoline or other ﬂ ammable vapors and liquids in the vicinity

of this or any other appliance.

WHAT TO DO IF YOU SMELL GAS

- Do NOT try to light any appliance.

- Do NOT touch any electrical switch.

- Do NOT use any phone in your building.

- Immediately call your gas supplier from a neighbor’s phone. Follow the gas

supplier’s instructions.

- If you cannot reach your gas supllier, call the ﬁ re department.

Should overheating occur or the gas supply fail to shut off, do not turn off or

disconnect the electrical supply to the pump. Instead, shut off the gas supply

at a location external to the boiler.

!

DANGER

!

WARNING

!

WARNING

!

WARNING

Installation & Servicing Instructions Rinnai Q-Series

6

Chemicals that are corrosive in nature should not be stored or used near the

boiler or vent termination.

1.5 Follow these instructions for the space heating water

Unsuitable heating system water can cause the formation of scale or sludge, which affects

system efﬁ ciency. It can also cause corrosion and reduce life of the heat exchanger.

– You must follow Rinnai guidelines for boiler water quality.

– Thoroughly ﬂ ush the system prior to ﬁ lling.

– Follow the Rinnai cleaning instructions.

– Never use water that has been treated by a reverse osmosis, D.I., or distilled water

to soften the water to ﬁ ll the heating system.

– Do not use inhibitors or other additives unless approved by Rinnai for that purpose.

– When freeze protection of the heating system is desired, only use Rinnai-approved

antifreezes. The allowed maximum concentration is 50%.

– When using oxygen-permeable pipes, e. g. for under ﬂ oor heating systems, you

must separate the system from the boiler using plate heat exchangers.

– Valve off boiler while ﬂ ushing system, do not introduce any system cleaner into the

boiler loop. Flush system thoroughly to remove all system cleaner before ﬁ lling boiler.

Approved antifreeze: • Rhomar RhoGard Mutli-Metal (AL safe) • Sentinel X500

(max. concentration 50%) • Noble Noburst AL • Fernox Alphi 11

Approved system cleaner: • Noble Noburst Hydronic System Cleaner • Fernox F3 Cleaner

• Rhomar Hydro-Solv 9100 • Sentinel X400

The system cleaners from NoBurst, Rhomar, and Fernox are not to be used in

the boiler. The boiler must be closed off (valved off) from the rest of the system

or not connected while the cleaners are in the system. The system should then

be drained and then thoroughly ﬂ ushed with clean water to remove all the

system cleaner.

Approved inhibitors: • Rhomar Pro-tek 922 • Sentinel X100

• Noble Noburst AL inhibitor

See the Rinnai Boiler Applications Manual or Chapter 6 and 10 of this manual for

additional information.

If problems occur when using sanitary water with a chlorine content

higher than 150 mg/l, no recourse can be made to the terms of the limited

warranty.

1.6 Tools, materials and additional equipment

For the installation and maintenance of the boiler you will need:

– Standard tools for space heating, gas and water ﬁ tting

– Digital manometer that is capable of reading both positive and negative pressures

– Combustion analyzer (intended for use with condensing boilers)

– Digital multimeter

– pH digital meter

– Metric Allen wrenches

– Metric socket wrenches

In addition, a handtruck with a fastening belt is useful.

For maintenance of the boiler you will need, apart from standard tools for space

heating, gas and water ﬁ ttings the following items:

- Rinnai toolkit Q and E-Series

NOTICE

i

NOTICE

i

NOTICE

i

Installation & Servicing Instructions Rinnai Q-Series

7

1.7 Relevant Installation, Service and User manuals

– Approved vent system

– Rinnai Boiler Applications Manual

– User manual

1.8 Disposal

– Dispose of the boiler packaging in an environmentally sound manner.

– Dispose of components of the heating system (e.g. boiler or control device), that

must be replaced in an environmentally responsible manner.

2 Regulations and guidelines

The installation must comply to the requirements of the authority having jurisdiction

or, in the absence of such requirements, to the latest edition of the National Fuel Gas

Code, ANSI Z223.1/NFPA 54. In Canada, installation must be in accordance with

the requirements of CAN/CSA B149.1, Natural Gas and Propane Installation Code.

Where required by the authority having jurisdiction, the installation must comply to

the Standard for Controls and Safety Devices for Automatically Fired Boilers, ANSI/

ASME CSD-1.

Install CO detectors per local regulations. Boiler requires an inspection every 2 years or

4000 hours and maintenance every 4 years or 8000 hours. See maintenance section

chapter 14.

Operating Limits of the boiler:

Max. boiler temperature: 176 °F (80 °C)

Max. operating pressure: 45 psi (3 bar)

Max. Allowable Working Temperature ASME: 200 °F (93 °C)

Max. Allowable Working Pressure ASME: 45 psi (3 bar)

The hot water distribution system must comply with all applicable codes and

regulations. When replacing an existing boiler, it is important to check the condition

of the entire hot water distribution system to ensure safe operation.

Installation & Servicing Instructions Rinnai Q-Series

8

3 Description of the boiler

The Rinnai Q boiler is a room sealed, condensing and modulating central heating

boiler, with an optional integrated DHW cylinder (integrated DHW on the Q175C only).

The QxxS boiler models have the ability to control a domestic hot water indirect tank.

The boiler is provided with a compact stainless steel heat exchanger with smooth

tubes. This design is a well engineered principle using durable materials.

The boiler burns gas for supplying heat. The heat is transferred in the heat exchanger

to the water in the central heating system. By cooling down the exhaust gases

condensate is formed. This results in high efﬁ ciency. The condensate, which has

no effect on the heat exchanger and the function of the boiler, is drained through a

condensate collector trap.

The boiler is provided with an intelligent control system (CMS Control Management

System). The boiler anticipates the heat demand of the central heating system or the

domestic hot water facility system.

When an outdoor sensor is connected to the boiler it will operate weather dependantly

using outdoor reset. This means that the boiler control measures the outside

temperature and supply temperature. With this data the boiler calculates the optimal

supply temperature for the installation.

Explanation of the type indication: Rinnai Q205SN

Q = Type

205 = Nominal load in (x1,000) BTU

S = System/Solo (C = Combi)

N = Natural Gas (P = Propane Gas)

Different boilertypes:

Room sealed boiler

The boiler retreives its

combustion air from outside

then discharges the ﬂ ue

gasses to the outside.

Condensing

Retrieves heat as much as

possible from the ﬂ ue gasses.

Water condensates on the

heat exchanger.

Modulating

Stepless higher or lower

burning according to the heat

demand.

System/Solo boilers: Combi boiler with integrated DHW cylinder

Q85SN, Q130SN Q175SN, Q205SN Q175CN

Q85SP, Q130SP Q175SP, Q205SP Q175CP

Installation & Servicing Instructions Rinnai Q-Series

9

4 Packaging and transportation

4.1 Scope of delivery

The boiler is supplied ready for use.

• Please check if the packaging is intact.

• Check if all the items listed are included in the delivery.

The supply kit contents:

!

CAUTION

4.2 Transportation

The boiler may be damaged when not secured properly.

- Only transport the boiler using appropriate transportation equipment, such as a

handtruck with a fastening belt or special equipment for maneuvering steps.

- When shipping the boiler must be secured on the transportation equipment to

prevent it from falling off.

- Protect all parts against impacts if they are to be transported.

- Follow the transportation markings on the packaging.

• Packaged boilers must always be lifted and carried by two people, or you must

use a handtruck or special equipment for transport.

Description

Q85S

Q130S

Q175S

Q205S

Q175C

Boiler with:

Outdoor reset sensor ARV12 1 1 1

Compression ring Ø15 brass 4

Compression ring Ø22 brass 2

Compression ring Ø28 brass 2

Compression ring Ø35 brass 2 2

Bolt M5X16mm 1 1 1

Cover air supply Ø120/Ø80 1 1 1

Gasket vent system ø80 1 1 1

Power cable pull safety Q-Series 1 1 1

Flue pipe Ø 80 PP 1 1 1

Nut 15mm compression fitting 2

Nut W1.1/8x1/14 22 Compression fitting 1

Nut W1.3/8"x1/14 28 compression fitting 2

Nut W1.610x1/14 35 compression fitting 2 2

Screw 6X60mm 5 5 5

Lip-ring flue pipe ø80 1 1 1

Feed through + plug flue gas 1 1 1

Cap de-aerator 1 1 1

Adapter fitting 15mm x 3/4"NPT ext. 2

Adapter fitting 22mm x 3/4"NPT ext. 1

Flue adapter Ø80/Ø3" pps UL appr. 2 2 2

Flow restriction MR01 FG 21,0L red 1

Wall mounting suspension bracket 1 1 1

Plumbing kit Q85S/Q130S 1 1

Plumbing kit Q175S/Q175C/Q205S 1

3/4" Gas valve 1 1 1

Template on inside of package 1 1 1

Installation & Service Instructions 1 1 1

User information manual 1 1 1

Warranty document 1 1 1

ICSL book 1 1 1

Amoun

t

Installation & Servicing Instructions Rinnai Q-Series

10

5 Installation

5.1 Requirements for the installation room

- The room where the boiler will be placed must always be free from freezing

conditions.

- Do not store or use gasoline or other ﬂ ammable vapors and liquids in the

vicinity of this or any other appliance.

- Never use or store any chlorinated detergents or halogenated hydrocarbons

(e.g. in spraycans, solvents and detergents, paints, adhesives) in proximity

of the boiler.

- The boiler must be installed in such a way that it is protected from water

(dripping, spraying, rain, etc.) during operation and service (circulator

replacement, condensate trap, control replacement, etc.)

- This boiler is for intended for indoor installations only.

Products to avoid present in boiler room

and/or around combustion air intake

Spray cans containing chloro-/fluorcarbons

Ammonium and/or ammonium solutions

Permanent wave solutions (hair product)

Chlorinated waxes and/or cleaners

Swimming pool chemicals based on chlorine

Calcium chloride used for thawing

Sodium chloride used for water softening

Refrigerant leaks

Paint or varnish removers

Hydrochloric acid/muriatic acid

Cements and glues

Antistatic fabric softeners used in clothes dryers

Chlorine-type bleaches, detergents, and cleaning solvents

found in household laundry rooms

Adhesives used to fasten building products and

other similar products

Areas likel

y

to have contaminants

Dry cleaning/laundry areas and establishments

Swimming pools

Metal fabrication plants

Beauty shops

Refrigeration repair shops

Photo processing plants

Auto body shops

Plastic manufacturing plants

Furniture refinishing areas and establishments

New building construction

Remodeling areas

Garages with workshops

!

DANGER

Installation & Servicing Instructions Rinnai Q-Series

11

5.2 Fitting the boiler

- Remove the packaging materials.

- Do not tear the packaging. Take notice of the presence of the mounting

template at the inside of the carton wrapper.

- Lay the boiler on its back during unpacking. When unpacking, the casing can

be removed from the boiler. This part can be kept apart during installation. It

must be placed on the boiler and ﬁ xed with the screw behind the door before

the boiler is started up.

Turn the boiler to its side and remove the wall bracket from the back of the

boiler by removing the 2 screws.

The boiler can be mounted practically to any wall with the suspension bracket and the

enclosed mounting equipment.

- The wall must be ﬂ at and of sufﬁ cient strength in order to be able to securely hold

and support the boiler weight with its water content.

- Take note of the necessary space around the boiler for installation of venting

system, pipework and servicing. See drawing in section 5.3.

The location of the boiler can be determined by using the template which is printed

on the inside the boiler package wrapping. Remember to account for the spacing of

the plumbing kit.

- Drill the necessary holes using the template

- Install the mounting bracket to the wall using the supplied mounting materials

Lifting and carrying precautions.

To avoid personal injury please follow these recommendations:

- Always lift the boiler with 2 people or use special equipment.

- When lifting the boiler, bend the knees, and keep the back straight and feet

apart.

- Do not lift and twist at the same time.

- Lift and carry the boiler close to the body.

- Wear protective clothing and gloves to protect from any sharp edges.

Lift the boiler only by the boiler's rear wall. Do not lift using the pipes on the

bottom of the boiler or the vent connections on the top of the boiler.

- Dispose the packaging materials.

!

CAUTION

NOTICE

i

NOTICE

i

!

WARNING

Installation & Servicing Instructions Rinnai Q-Series

12

5.3 Dimensions

dimensions Q85S, Q130S, Q175S and Q205S figure 1

C

E

F

A

T

B

Q

R

B

H

J

K

G

H

J

K

D

W

C

E

F D

Q

G

A

P

U

T

P

U

R

X

Y

X

Y

Z

dimensions Q175C figure 2

T

B

R

H

J

K

G

D

aa

C

E

F

Q

S

A

P

U

X

Y

Z

O

N

L

aa

V1

aa

V2

V1

V2

V1

V2

Installation & Servicing Instructions Rinnai Q-Series

13

dimensions table 1

Boiler type Combi

Q85SN/Q85SP Q175SN/Q175SP

Q130SN/Q130SP Q205SN/Q205SP Q175CN/Q175CP

inch / mm inch / mm inch / mm

A Height 26.8" / 680 26.8" / 680 26.8" / 680

B Width 19.7" / 500 26" / 660 39.4" / 1000

C Depth 15.2" / 385 15.2" / 385 15.2" / 385

D Left side / vent 13.2" / 335 19.5" / 495 19.5" / 496

E Center to center / vent and air supply 4.7" / 120 4.7" / 121 4.7" / 122

F Back / vent 10.6" / 270 10.6" / 270 10.6" / 270

G Left side / gas pipe 2.6" / 65 2.6" / 65 2.6" / 65

H Left side / supply pipe 7.8" / 199 7.8" / 199 7.8" / 199

J Left side / return pipe 16.8" / 428 19.8" / 504 19.8" / 504

K Left side / condensate pipe 14.6" / 370 20.9" / 530 20.9" / 530

L Left side / expansion pipe 23.2" / 590

N Left side / cold water pipe 34.8" / 885

O Left side / hot water pipe 37.6" / 955

P Pipe length of g* 0.7" / 18 0.7" / 18 0.7" / 18

Q Pipe length of c* 2" / 50 2" / 50 2" / 50

R Pipe length of f and r* 17.7" / 450 18.5" / 470 18.5" / 470

S Pipe length of e, k and w* 3.5" /89

T Back / Center of pipe c* 1" / 25 1" / 25 1" / 25

U Back / Center of pipe g* 1.6" / 40 1.6" / 40 1.6" / 40

V1

Back / Center of pipe f, r, e, k and w* 2" / 50 2" / 50 2" / 50

V2

Back / Center of pipe f and r* 2.1" / 54 2.1" / 54 2.1" / 54

W

Pipe length vent co-axial

Pipe length vent parallel

2.6" / 65

5.8" / 147

2.6" / 65

5.8" / 147

2.6" / 65

5.8" / 147

X Bottom side boiler to center safety valve 7.7" / 195 8" / 200 8" / 200

Y

Bottom side boiler to center header 10.2" / 260 10.4" / 265 10.4" / 265

Z

Center to center of f and r* 9" / 229 12" / 305 12" / 305

aa

Depth plumbing kit 5.6" / 142 5.6" / 142 5.6" / 142

*) See figure 3

Solo

Dimensions

Installation & Servicing Instructions Rinnai Q-Series

14

connection diameters table 2

boiler connections figure 3

Connection for combustion air supply and vent system

Boiler type Combi

Q85SN/Q85SP Q175SN/Q175SP

Q130SN/Q130SP Q205SN/Q205SP Q175CN/Q175CP

Vent system / Combustion air supply

80/125mm 80/125mm 80/125mm

Gas pipe

g 3/4"M-NPT 3/4"M-NPT 3/4"M-NPT

Supply pipe boiler side - f1

28mm 35mm 35mm

system side - f2

1¼"M-NPT 1½"M-NPT 1½"M-NPT

Return pipe boiler side - r1

28mm 35mm 35mm

system side - r2

1¼"M-NPT 1½"M-NPT 1½"M-NPT

Condensate pipe c

0.95" / 24mm 0.95" / 24mm 0.95" / 24mm

Expansion pipe e

0.87"x ¾"M-NPT /

22mm

Cold water pipe k

0.6"x ¾"M-NPT /

15mm

Hot water pipe w

0.6"x ¾"M-NPT /

15mm

Supply pipe indirect tank.

In case of optional internal

3 way valve.

t 1"M-NPT

Solo

Dimensions

g f1 r1 c

f2 r2

g f1 r1 c

e k w

f2 r2

g f1 r1 c

t

f2 r2

Installation & Servicing Instructions Rinnai Q-Series

15

5.3.1 Plumbing Kits

Rinnai boilers are supplied with a Plumbing kit from factory. Find below the dimensions.

See chapter 6.1 for additional information.

2.0”

50mm

2.1”

54mm

142

[5.6”]

9”

229mm

3.9”

100mm

8.6”

219mm

4.7”

119mm

5.2”

131mm

14.2”

360mm

16.4”

416mm

17.6”

448mm

2.0”

50mm

2.1”

54mm

[5.6”

142mm

10.2”

260mm

12”

305mm

15”

381mm

4.7”

120mm

5.2”

133mm

17.2”

438mm

19.7”

501mm

18.6”

474mm

Plumbing Kit 3

Suitable for:

Q175SN / Q175SP

Q175CN / Q175CP

Q205SN / Q205SP

Plumbing Kit 2

Suitable for:

Q85SN / Q85SP

Q130SN / Q130SP

Plumbing kit 2 ﬁ gure 4

Plumbing kit 3 ﬁ gure 5

Installation & Servicing Instructions Rinnai Q-Series

16

5.3.2 Clearences from the boiler

Minimum required clearances

to combustibles

Minimum required clearances

to non-combustibles

Recommended

service clearances

All types

A

ll types

A

ll types

inch / mm inch / mm inch / mm

Top of boiler 2" / 50 2" / 50 10" / 250

Back of boiler 0" 0" 0

Front of boiler 6" / 150 6" / 150 24" / 600

Left side of boiler 2" / 50 2" / 50 2" / 50

Right side of boiler 2" / 50 2" / 50 2" / 50

Floor / Ground to

bottom of boiler

12" / 300 12" / 300 30" / 762

Floor/ Ground to

bottom Low loss

header

0" 0" 12" / 300

Vent 0" 0" 0"

clearances to the boiler table 3

wall

2"

50

ceiling

Min. 10" /

250mm

15.7"

400

24"

600

service clearances to the boiler figure 6

For closet installation: clearance is 1” / 25mm from the front.

Low Loss Header

Clearances to combustible and non-combustible is 0 inch for sides, top, front and ﬂ oor/ground

The recommended service clearance to the bottom of the low loss header is 12 inches.

2"

50

Installation & Servicing Instructions Rinnai Q-Series

17

5.4 Technical speciﬁ cations

Technical specifications Table 4

Combi

Q175CN Q85SN Q130SN Q175SN Q205SN

Boiler type Q175CP Q85SP Q130SP Q175SP Q205SP

Input Hs CH BTU/hr 175,000 85,000 130,000 175,000 205,000

kW 51 25 38 51 60

Q

n

Output non-condensing CH

BTU/hr 157,000 77,000 117,000 157,000 184,000

kW 45.9 22.5 34.2 45.9 54.0

Q

n

Output EN677 efficiency CH

BTU/hr 172,400 84,000 127,600 172,400 202,200

kW 50.2 24.7 37.3 50.2 59.1

Q

n

Output AFUE CH

BTU/hr 167,500 82,000 124,900 167,500 196,100

kW 48.8 24.1 36.5 48.8 57.4

Efficiency at 98.6/86°F (36/30°C) part

load, Hs, EN677 CH

% 98.5 98.8 98.2 98.5 98.5

AFUE according IBR % 95.0 95.4 95.4 95.0 95.0

O

2

(at full load)

%

Electr. power consumption max. W 210 137 144 210 234

Electr. power consumption stand by W

Current V/Hz

Fuse rating A

Degree of protection acc. EN 60529

Weight (empty) lbs / kg 196 / 89 110 / 50 117 / 53 141 / 64 141 / 64

Water content CH gallon / liter 1.8 / 7 0.9 / 3.5 1.3 / 5 1.8 / 7 1.8 / 7

Water content DHW gallon / liter 3.7 / 14

Water content Plumbing Kit gallon / liter 0.74 / 2.8

Q-Series

Natural gas: 4.4 - 4.7 (Propane: 4.8 - 5.1)

IPX0D

14

120Vac/60Hz

5AF & 4AT

0.58 / 2.2 0.74 / 2.8

After run time pump CH min

After run time pump DHW min

P

MS

Water pressure min.-max.

PSI / bar

P

MW

Water pressure DHW max.

PSI / bar 150 / 10

n.a. n.a. n.a. n.a.

Flow temperature max. °F / °C

Pump type UPER 20-78 UPER 20-58 UPER 20-78 UPER 20-78 UPER 20-78

A

vailable pump hei

g

ht CH

(

'

T = 25K

)

PSI / kPa 2.9 / 20 5.2 / 36 3.0 / 21 2.9 / 20 5.5 / 38

Approvals ASME, CSA ASME, CSA ASME, CSA ASME, CSA ASME, CSA

DHW flow

(

at 'T50°F

)

gallon/min 6.2

DHW flow

(

at 'T27.8°C

)

liter/min 23.5

DHW flow

(

at 'T75°F

)

gallon/min 4.1

DHW flow

(

at 'T41.7°C

)

liter/min 15.5

Max. DHW flow rate gallon/min 6.2

liter/min 23.5

Pressure difference DHW PSI / bar 4.3 / 0.3

CSA number

CRN number

2183087

5

1

14-43 / 1-3

176 / 80

8101.7CL

Installation & Servicing Instructions Rinnai Q-Series

18

6 Connecting the boiler

The boiler has the following connection pipes;

- The central heating circuit pipes.

These must be connected to the Plumbing Kit by means of adapter ﬁ ttings.

See further chapter 6.1;

- The gas supply pipe.

It is provided with a 3/4" male thread into which the tail piece of the gas valve can

be screwed. See further chapter 6.4;

- The condensation drain pipe.

It consists of an oval 1" (24 mm) plastic pipe. The drain pipe can be connected to

this by means of an open connection. If the open connection is ﬁ tted in a different

location, then the pipe can be lengthened by means of a 1 1/4" (32 mm) PVC

sleeve. See further chapter 6.6;

- The vent system and air supply system.

It consists of a concentric connection 3"/5" (80/125 mm). The boiler can be converted

to a twin pipe connection that will accept 80mm ﬂ ue and intake air or with the use

of the included adapters 3” PVC / CPVC ﬂ ue and intake. See further chapter 6.7.

- Cold and hot water pipes for domestic hot water (DHW).

Combi boilers only: These consist of 3/4" (15 mm) copper pipe and can be

connected to the installation by means of 3/4" M-NPT adapter ﬁ ttings. See further

chapter 6.5;

The pipes to be connected to the boiler must be cleaned before connecting in

order to prevent dirt from entering and damaging the boiler.

6.1 Central heating system

Connect the central heating system according to its instructions.

The boiler pipes can be connected to the installation by means of compression ﬁ ttings.

Reducers should be used for connecting to thick-walled pipe (welded or threaded).

When removing the plastic sealing caps from the pipes, dirty testing water may

drain from the boiler.

A Plumbing Kit must be ﬁ tted to the boiler.

The boiler, when used in connection with a refrigeration system, must be

installed so the chilled medium is piped in parallel with the boiler with appropriate

valves to prevent the chilled medium from entering the boiler.

The boiler piping system of a hot water boiler connected to heating coils located

in air handling units where they may be exposed to refrigerated air circulation

must be equipped with ﬂ ow control valves or other automatic means to prevent

gravity circulation of the boiler water during the cooling cycle.

NOTICE

i

NOTICE

i

NOTICE

i

NOTICE

i

NOTICE

i

Installation & Servicing Instructions Rinnai Q-Series

19

Boiler basic piping ﬁ gure 7

T

P

Low Loss Header

V1

Service valve

V2

Service valve

1

2

3

4

56

7

89

1. shut off valve

2. system circulator

3. check valve

4. balancing valve

5. boiler drain valve

6. dirt trap

7. air separator

8. automatic ﬁ ll valve

9. back ﬂ ow preventer

10. expansion tank

11. bypass for system cleaning

10

11

Installation & Servicing Instructions Rinnai Q-Series

20

6.1.1 Plumbing Kit installation

Rinnai supplies speciﬁ c Plumbing Kits with each boiler type, which must be ﬁ tted

directly underneath the boiler on the supply and return pipe. Find in chapter 5.3 the

dimensions. Use of the Rinnai boiler without the plumbing kit will void the warranty.

To protect the entire heating system we recommend installing a dirt particle trap

in the return circuit. When the boiler is installed to an existing heating system

this trap is required. Use of a Y strainer is not permitted as a substitute for a

dirt trap.

- Install shut-off valves immediately before and after the dirt particle ﬁ lter to allow

the trap to be cleaned.

- Position 3 (ﬁ gure 8) is a garden hose thread boiler drain that can be used to drain

the boiler or add water treatment additives to the system such as inhibitors or

glycol.

- Position 4 (ﬁ gure 8) is the supply connection for an indirect tank when used with

the optional 3-way valve kit.

- For information on locating the expansion tank and system ﬁ ll, please see the

Rinnai Boiler Applications Manual.

Thoroughly ﬂ ush all pipes and radiators. We recommend the use of a Rinnai

approved system cleaner. Please refer to the list of approved Rinnai system

cleaners in this chapter.

- Refer to the installation template and chapter 5.3 for the pipe connection dimensions.

The plumbing kit is not intended to support the weight of the piping. Appropriate

piping supports should be used to support all attached piping to the boiler and

plumbing kit.

NOTICE

i

NOTICE

i

Plumbing Kit installation ﬁ gure 8

5

9

Compression fittings.

Parts:

1. Nut

2. Ferrule

3. Fitting

Fitting instructions:

1. Push the complete

fitting over the pipe as

far as possible. Ferrule

should be over the

pipe completely.

2. Turn the nut handtight

clockwise.

3. Use 2 wrenches, one

to hold the fitting on

its place, the other

for tighten the nut

clockwise in 3/4 turn.

21

3

1. Plumbing kit

2. Safety valve

3. Drain and Purge connection

4. DHW ﬂ ow connection

in case of optional

internal 3 way valve

5. Bronze adapter ﬁ ttings

6. Service valves*

7. Flow

8. Return

9. Pressure gauge*

2

1

3

4

6

8

7

* After installation of the plumbing kit to

the boiler the pressure gauge and both

handles of the service valves must be

mounted. Be sure the gauge is ﬁ tted leak

free and that the handles are secured with

the supplied nuts.

NOTICE

i

NOTICE

i

La page est en cours de chargement...

Rinnai Q205SN Guide d'installation

Rinnai Q205SN Guide d'installation

dans d''autres langues

Documents connexes

Autres documents