Jenn-Air JER8885RAB Le manuel du propriétaire

JENN-AIR ELECTRIC RANGE

TABLE OF CONTENTS

Important Safety Instructions .....................................1-3

Care & Cleaning ..............................................................4-6

Maintenance .........................................................................7

Troubleshooting ..............................................................8-9

Surface Cooking .........................................................10-12

Oven Cooking ..............................................................13-20

Options ..........................................................................21-24

Favorites ...............................................................................25

Setup ..............................................................................26-28

Accessories .........................................................................28

Warranty & Service ...........................................................29

Guide de d'utilisation et d'entretien ..........................30

Guia de uso y cuidado ....................................................66

JENN-AIR

Form No A/04/06 Part No 8113P619-60 '_2006 Maytag Appliances Sales Co.

Lithe U.S.A

or replace any part of your appliance unless it is

specifically recommended in this guide. All other

servicing should be referred to a qualified servicer.

Always disconnect power to appliance before servicing.

General instructions

M PORTANT SAFETY

NSTRU

Warning and Important Safety Instructions appearing in

this guide are not meant to cover all possible conditions

and situations that may occur. Common sense, caution,

and care must be exercised when installing,

maintaining, or operating the appliance.

Always contact the manufacturer about problems or

conditions you do not understand.

Recognize Safety Symbols, Words, Labels

To check if device is properly installed, look underneath

range with a flashlight to make sure one of the rear

leveling legs is properly engaged in the bracket slot. The

anti-tip device secures the rear leveling leg to the floor

when properly engaged. You should check this anytime

the range has been moved.

To Prevent Fire or Smoke

Damage

Be sure all packing materials are removed from the

appliance before operating it.

Keep area around appliance clear and free from

combustible materials. Flammable materials should not

be stored in an oven.

Many plastics are vulnerable to heat. Keep plastics away

from parts of the appliance that may become warm or

hot.

To prevent grease fires, do not let cooking grease or

other flammable materials accumulate in or near the

appliance.

Read and follow all instructions before using this

appliance to prevent the potential risk of fire, electric

shock, personal injury or damage to the appliance as a

result of improper usage of the appliance. Use appliance

only for its intended purpose as described in this guide.

To ensure proper and safe operation: Appliance

must be properly installed and grounded by a qualified

technician. Do not attempt to adjust, repair, service

In Case of Fire

Turn off appliance and ventilating hood to avoid

spreading the flame. Extinguish flame, then turn on

hood to remove smoke and odor.

• Cooktop: Smother fire or flame in a pan with a lid or

cookie sheet.

• NEVER pick up or move a flaming pan.

• Oven: Smother fire or flame by closing the oven door.

Do not use water on grease fires. Use baking soda, a

dry chemical or foam-type extinguisher to smother fire

or flame.

Child Safety

Do not touch a hot oven light bulb with a damp cloth as

the bulb could break. Should the bulb break, disconnect

power to the appliance before removing bulb to avoid

electrical shock.

NEVER use aluminum foil to cover an oven rack or oven

bottom. Misuse could result in risk of electric shock, fire,

or damage to the appliance. Use foil only as directed in

this guide.

NEVER leave children alone or unsupervised near the

appliance when it is in use or is still hot. Children

should never be allowed to sit or stand on any part of

the appliance as they could be injured or burned.

Children must be taught that the appliance and utensils

in it can be hot. Let hot utensils cool in a safe place, out

of reach of small children. Children should be taught

that an appliance is not a toy. Children should not be

allowed to play with controls or other parts of the

appliance.

About Your Appliance

To prevent potential hazard to the user and damage to

the appliance, do not use appliance as a space heater to

heat or warm a room. Also, do not use the oven as a

storage area for food or cooking utensils.

Do not obstruct the flow of air by blocking the oven vent.

DO NOT TOUCH HEATING ELEMENTS OR INTERIOR

SURFACES OF OVEN. Heating elements may be hot even

though they are dark in color. Interior surfaces of any

oven become hot enough to cause burns. During and

after use, do not touch, or let clothing or other

flammable materials contact heating elements or interior

surfaces of oven until they have had sufficient time to

cool. Other surfaces of the appliance may become hot

enough to cause burns - among these surfaces are: oven

vent opening and surface near this opening, oven door

and window of oven door.

When the oven is in use, the area near the oven vent may

become hot enough to cause burns. For best baking

results, do not block the vent opening.

2

Cooking Safety

Never heat an unopened food container in the oven.

Pressure build up may cause container to burst

resulting in serious personal injury or damage to the

appliance.

Use dry, sturdy potholders. Damp potholders may cause

burns from steam. Dish towels or other substitutes

should never be used as potholders because they can

trail across hot elements and ignite or get caught on

appliance parts.

Wear proper apparel. Loose fitting or long hanging-

sleeved apparel should not be worn while cooking.

Clothing may ignite and cause burns if garment comes

in contact with heating elements.

Always place oven racks in the desired positions while

oven is cool. Slide oven rack out to add or remove food,

using dry, sturdy potholders. Always avoid reaching into

the oven to add or remove food. If a rack must be

moved while hot, use a dry potholder. Do not let

potholder contact hot element in oven.

Use racks only in the oven in which they were shipped/

purchased.

Use care when opening the oven door. Let hot air or

steam escape before removing or replacing food.

PREPARED FOOD WARNING: Follow food

manufacturer's instructions. If a plastic frozen food

container and/or its cover distorts, warps, or is otherwise

damaged during cooking, immediately discard the food

and its container. The food could be contaminated.

Do not allow aluminum foil or meat probe to contact

heating element.

Always turn off all controls when cooking is completed.

Utensil Safety

Follow the manufacturer's directions when using oven

cooking bags.

This appliance has been tested for safe performance

using conventional cookware. Do not use any devices

or accessories that are not specifically recommended in

this guide. Do not use add-on oven convection systems.

Theuseofdevicesoraccessoriesthatarenotexpressly

recommendedinthisguidecancreateserioussafety

hazards,resultin performanceproblems,andreducethe

lifeofthecomponentsoftheappliance.

Ifpanissmallerthanelement,aportionoftheelement

will beexposedto directcontactandcouldignite

clothingorpotholder.

Onlycertaintypesofglass,glass/ceramic,ceramic,

earthenware,orotherglazedutensilsaresuitablefor

cooktoporovenservicewithoutbreakingduetothe

suddenchangeintemperature.Followutensil

manufacturer'sinstructionswhenusingglass.

Turnpanhandletowardcenterofcooktop,notoutinto

theroomoroveranothersurfaceelement.Thisreduces

theriskofburns,ignitionofflammablematerials,or

spillageifpanisaccidentlybumpedorreachedbysmall

children.

Cooktop

NEVER leave surface units unattended, especially when

using high heat. An unattended boilover could cause

smoking and a greasy spillover can cause a fire.

This appliance is equipped with different size surface

elements. Select pans with flat bottoms large enough to

cover element. Fitting pan size to element will improve

cooking efficiency.

GLASS-CERAMIC SURFACE: NEVER cook on broken

cooktop. If cooktop should break, cleaning solutions and

spillovers may penetrate the broken cooktop and create

a risk of electric shock. Contact a qualified technician

immediately.

Deep Fat Fryers

Use extreme caution when moving the grease pan or

disposing of hot grease. Allow grease to cool before

attempting to move pan.

Ventilating Hoods

Clean range hood and filters frequently to prevent grease

or other flammable materials from accumulating on hood

or filter and to avoid grease fires.

When flaming foods under the hood, turn the fan on.

Cleaning Safety

Clean cooktop with caution. Turn off all controls and

wait for appliance parts to cool before touching or

cleaning. Use care to avoid steam burns if a wet sponge

or cloth is used to wipe spills on a hot surface. Some

cleaners can produce noxious fumes if applied to a hot

surface.

Clean only parts listed in this guide.

Self-Clean Oven

Do not clean door gasket. The door gasket is essential

for a good seal. Care should be taken not to rub,

damage, or move the gasket.

Do not use oven cleaners or oven liners of any kind in or

around any part of the self-clean oven.

Important Safety Notice

and Warning

The California Safe Drinking Water and Toxic

Enforcement Act of 1986 (Proposition 65) requires the

Governor of California to publish a list of substances

known to the State of California to cause cancer or

reproductive harm, and requires businesses to warn

customers of potential exposures to such substances.

Users of this appliance are hereby warned that when the

oven is engaged in the self-clean cycle, there may be

some low-level exposure to some of the listed

substances, including carbon monoxide. Exposure to

these substances can be minimized by properly venting

the oven to the outdoors by opening the windows and/or

door in the room where the appliance is located during

the self-clean cycle.

IMPORTANT NOTICE REGARDING PET BIRDS: Never

keep pet birds in the kitchen or in rooms where the

fumes from the kitchen could reach. Birds have a very

sensitive respiratory system. Fumes released during an

oven self-cleaning cycle may be harmful or fatal to birds.

Fumes released due to overheated cooking oil, fat,

margarine and overheated non-stick cookware may be

equally harmful.

Save These instructions for Future Reference

3

CARE CLEAN|N

Self-Clean Oven

To set Self=Clean: JJ.......................

' Clean

1. Press Clean pad. .... /

2. REMOVE RACKSwill be displayed. Remove the racks.

3. Select CONTINUE using the Quickset pad. The Quickset

pads are located on either side of the control panel display.

Set LIGHT soil level by entering 200 using the number pads

for two hours of cleaning time. Press the Enter pad.

OR

Select MEDIUM for a moderately soiled oven and three

hours of cleaning time.

The self-clean cycle uses above-normal cooking temperatures

to automatically clean the oven interior.

The oven should be cleaned regularly by wiping up spillovers

to prevent excessive smoke and flare-ups. Do not allow a

heavy build-up of soil to accumulate in the oven.

During the cleaning process, the kitchen should be well

ventilated to get rid of normal odors associated with cleaning.

Before Self-Cleaning

1. Turn off the oven light before cleaning. The oven light may

burn out during the clean cycle.

2. Remove broiler pan, all pans, and oven racks from the

oven. The oven racks will discolor and may not slide

easily after a self-clean cycle if they are not removed.

3. Clean oven frame, door frame, area / /

outside of gasket, and around the \

opening in the door gasket with a

nonabrasive cleaner such as Bon

Ami* or detergent and water. The

self-cleaning process does not

clean these areas. They should be

cleaned to prevent soil from baking on during the clean

cycle. (The gasket is the seal around the oven door and

window.)

4. To prevent damage, do not clean or rub the gasket around

the oven door. The gasket is designed to seal in heat

during the clean cycle.

5. Wipe up excess grease or spill-overs from the oven

bottom. This prevents excessive smoking, flare-ups or

flaming during the clean cycle.

6. Wipe up sugary and acidic spillovers such as sweet

potatoes, tomato, or milk-based sauces. Porcelain enamel

is acid-resistant, not acid-proof. The porcelain finish may

discolor if acidic or sugary spills are not wiped up before a

self-clean cycle.

OR

Select HEAVY for a heavily soiled oven and four hours of

cleaning time.

5. CLEAN,TIME, LOCKED and the cleaning time countdown

will be displayed while the oven is cleaning. OVEN

COOLINGwill appear in the display when the cleaning

time has been completed and the oven is still locked.

Important: The door lock will disengage approximately one

hour after the cleaning time is completed. OVENCOOLING

will go off in the display when the oven door has unlocked.

To Delay a Self=Clean Cycle:

1. Press Clean pad. Clean i

2. REMOVERACKSwill be displayed. ............................

Remove the racks.

3. Select CONTINUE using the Quickset pad.

4. Set LIGHT soil level by entering 200 using the number

pads for two hours of cleaning time. Press the Enter pad.

OR

Select MEDIUM for a moderately soiled oven and three

hours of cleaning time.

OR

Select HEAVY for a heavily soiled oven and four hours of

cleaning time.

5. The door will lock. CLEAN, TIME, LOCKEDand the

cleaning time countdown will be displayed

6. After door locks, press the More Options pad.

7. Select DELAY using the Quickset pad.

8. Select the number of hours you want to delay the start of the

self-clean cycle.

9. The delay time and cleaning time will be displayed.

* Brand names for cleaning products are registered trademarks of the respective manufacturers.

4

After Self=Cleaning

About one hour after the end of the self-clean cycle, LOCKwill

turn off. The door can then be opened.

Some soil may leave a light gray, powdery ash. Remove it

with a damp cloth. If soil remains after wiping, that means the

clean cycle was not long enough. The soil will be

removed during the next clean cycle.

If oven racks were left in the oven during a clean cycle

and do not slide smoothly, wipe racks and supports with a

small amount of vegetable oil to make them easier to move.

Fine lines may appear in the porcelain because it went

through heating and cooling. This isnormal and will not

affect performance.

A white discoloration may appear after cleaning if acidic

or sugary foods were not wiped up before the self=clean

cycle. This discoloration is normal and will not affect

performance.

Cleaning Procedures

Notes:

• If the oven door is left open, CLOSEDOORwill appear in

the display until the door isclosed.

• If more than 30 seconds elapse between pressing the

Clean pad and pressing a number pad, the program will

automatically return to the previous display.

• The oven door will be damaged if it isforced to open

during cleaning or cooling process.

° The first few times the oven iscleaned, some smoke and

odor may be detected. This isnormal and will lessen or

disappear with use. If the oven isheavily soiled, or if the

broiler pan was accidently left in the oven, excessive

smoke and odor may occur.

° As the oven heats and cools, you may hear sounds of

metal parts expanding and contracting. This isnormal and

will not damage your appliance.

i¸ii¸iiilii!_i_i!i!i!i!i!ii!iiili!ii!ii!i!iii!ii!i!i!!!iliiililiiilililililiiiliiiiliiliiliiliiiiiilililililililiiililililiiliiiiiiiiiiiiiiiiii!ii!ii!ii!iiiii!iliiiii!iiii!iii_!_i_ii_i_i!_i!ii_i_iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii!!!i!i!!i!!i!!i!!i!!i!!i!!!i!!i!!i!i!!i!!i!!i!!!!iiiiilliiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii!iii!iiiiiiiiiiiiiiiiiiiiiiiiiililiiililiiililiii!ii!!ii!!iiiiiiiiiiiiiiiiiiiiiiiiiiililiiililiiililililiiililiiililililiiililiiililililiiililiiilililililiiiliiliiliililliiliililiiiliiliiliililliiliililiiiliiiiiiiiiiiiii!iiiiiiiiiiiiiiiiiiiiiiiiiiiii!i!i!i!iiiiliilillillii!ililiiiliiiii!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!iiiiiiliiiliiliiliiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiilliiiiiiiliiiiiiiiiiiiiilliiiiiiiliiiiiiiiiililililiii!ii!!ii!!iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiilii!iii!iii!iiliiliililiiiliiliiliiiiiilliililiiiiiiiiiiif!ill!!!i!!!ii!i

_,_,_,_,_,_,_,_,_,_,,_,_'_ ,_,_;_,;_;,;_;,;_;,_;_,___,_,_,__,_,_,_,_,_,____,___=,_,,__t_t_t_t_t_t_t_t_t_t_t_t_t_t_t_t_t_t_t_t_t_t_t_t_t_t_t_t_t_t_t_______________,___________,_,,,,,_ __;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;__,__;,_;,_;,_;,_;,_;,_;,_;,_;,_,___;,_;,_;,_;,_;,_;,_;,_;,_;,_;,_;,_;,_;,_;,_;,_;,,,_,__:_ _ _,__,__,__,_,__,__,__,_,___;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;;___;,_;,_;,_;,_;,_;,_;,_;,_;,_;,_;,_,:_ _;,_;,_;,_;,_;,_;,_;,_,:,__,__,__,__,_,__,__,__,_,__,__,__,_,__,__,__,_,__,__,__,_,__,__,__,_,__,__,__,_,___;,_;,_;,_;,_;,_;,_;,_

Backguard and Porcelain enamel is glass fused on metal and may crack or chip with misuse. It isacid-resistant, not acid-

Cooktop - proof. All spillovers, especially acidic or sugary spillovers, should bewiped up immediately with a dry cloth.

Porcelain Enamel • When cool, wash with soapy water, rinse and dry.

• Never wipe off a warm or hot surface with a damp cloth. This may cause cracking or chipping.

° Never use oven cleaners, abrasive or caustic cleaning agents on exterior finish of range.

Broiler Pan and Never cover insert with aluminum foil as this prevents the fat from draining to the pan below.

Insert ° Place soapy cloth over insertand pan; let soak to loosen soil.

° Wash inwarm, soapy water. Use scouring pad to remove stubborn soil.

° Broiler pan and insertcan be cleaned in dishwasher.

Clock and • To activate control lock for cleaning, see Locking the Control,page 14.

Control Pad • Wipe with a damp cloth and dry. Do not use abrasive cleaning agents as they may scratch the finish.

Area • Glass cleaners may be used ifsprayed on a cloth first. DO NOTspray directly on controlpad and

display area.

Control Knobs ° Remove knobs in the Off position by pulling forward.

• Wash, rinse and dry. Do not use abrasive cleaning agents as they may scratch the finish.

• Turn on each element to be sure the knobs have been correctly replaced.

Warming Drawer, ° When cool,wash with warm, soapywater, rinseand dry.Never wipe a warm or hotsurface with adampcloth

Door Handle, Side as this maydamage the surfaceand may cause a steam burn.

Panels - Painted ° Forstubborn soil, use mildly abrasive cleaning agents such as baking soda pasteor Ben Ami.* Do net use

Enamel abrasive,causticor harshcleaningagentssuch assteelwool padsorovencleaners.Theseproductswill scratch

or permanently damage the surface.

Important: Use a dry towel or cloth to wipe up spills, especially acidic or sugary spills. Surface may

discolor or dull if soil is not immediately removed. Thisis especially important for white surfaces.

• Brand names for cleaning products are registered trademarks of the respective manufacturers.

•* To order direct, call 1-800-JENNAIR (1-800-536-6247].

5

Cooktop - Never use oven cleaners, chlorine bleach, ammonia or glass cleaners with ammonia.

Glass-Ceramic Important: Call an authorized servicer if the glass-ceramic top should crack, break or if metal or

aluminum foil should melt on the cooktop.

• Allow the cooktop to cool before cleaning.

• General - Cleancooktop after each use,or when needed, with a damp paper towel and Cooktop Cleaning

Creme* (Part No. 20000001)**.Then, buff with a clean, dry cloth.

Important: Permanent stains will develop ff soil is allowed to cook on byrepeatedly using the cooktop

when soiled.

• Heavy Soils or Metal Marks - Dampen a "scratchless" or "never scratch" scrubber sponge. Apply

Cooktop Cleaning Creme* (Part No. 20000001)** and scrub to remove as much soil as possible. Apply a

thin layer of the creme over the soil, cover with a damp paper towel and let stand 30 to 45 minutes (2-3

hours for very heavy soil). Keep moist by covering the paper towel with plastic wrap. Scrub again, then

buff with a clean, dry cloth.

Important: Only use a CLEAN,DAMP "scratchless" pad that is safe for non-stick cookware. Thepattern

and glass will be damaged ff the pad is not damp, ff the pad is soiled, or ff another type of pad is used.

• Burned-On or Crusty Soils - Scrub with a "scratchless" or "never scratch" scouring pad and

Cooktop Cleaning Creme*.

Important: Hold a razor blade scraper at 30°angle and scrape any remaining soil. Then,clean as

described above. Do not use the razor blade for daily cleaning as it may wear the pattern on / /

the glass.

Melted Sugar or Plastic - Immediately turn element to Low and scrape sugar or

plastic from hot surface to a cool area.Then turn element Off and allow to cool. Clean

residue with razor blade scraper and Cooktop Cleaning Creme*.

Oven Window • Avoid using excessive amounts of water which may seep under or behind glass, causing staining.

and Door - Glass ° Wash with soap and water. Rinsewith clear water and dry. Glass cleaner can be used if sprayed on a cloth

first.

° Do not use abrasive materials such as scouring pads, steel wool or powdered cleaners as they will

scratch glass.

Oven Interior • Follow instructions on pages 4-5 to set a self-clean cycle.

Oven Racks ° Clean with soapy water.

° Removestubborn soil with cleansing powder or soap-filled scouring pad. Rinse and dry.

° Rackswill permanently discolor and maynot slide smoothly if left in the ovenduring a self-clean operation.

If this occurs, wipe the rack edge and rack support with a small amount of vegetable oil to restore ease

of movement, then wipe off excess oil.

Stainless Steel • DO NOT USEANY CLEANING PRODUCT CONTAINING CHLORINE BLEACH.

(select models) • DO NOT USEABRASIIIE OR ORANGE CLEANERS.

• ALWAYS WIPE WITH THE GRAIN WHEN CLEANING.

• Daily Cleaning/Light Soil -- Wipe with one ofthe following - soapy water, white vinegar/water solution,

Formula 409 Glass and Surface Cleaner* or a similar glass cleaner - using a sponge or soft cloth. Rinse

and dry. To polish and help prevent fingerprints, follow with Stainless Steel Magic Spray (Part No.

20000008)**.

° NIoderate/Heavy Soil -- Wipe with one of the following -Bon Ami, Smart Cleanser, or Soft Scrub* -

using a damp sponge or soft cloth. Rinse and dry. Stubborn soils may be removed with a damp multi-

purpose Scotch-Brite* pad; rub evenly with the grain. Rinse and dry. Torestore luster and remove streaks,

follow with Stainless Steel Magic Spray*.

• Discoloration -- Using a damp sponge or soft cloth, wipe with Cameo Stainless Steel Cleaner*. Rinse

immediately and dry. To remove streaks and restore luster, follow with Stainless Steel Magic Spray*.

Brand names for cleaning products are registered trademarks of the respective manufacturers.

•* To order direct, call 1-800-JENNAIR (1-800-536-6247).

AINTENANCE

Oven Door

Oven Light

Important: The oven door on a new range may feel "spongy"

when it isclosed. This isnormal and will decrease with use.

Oven Window

To protect the oven door window:

1. Do not use abrasive cleaning agents such as steel wool

scouring pads or powdered cleansers as they may scratch

the glass.

2. Do not hit the glass with pots, pans, furniture, toys,or

other objects.

3. Do not close the oven door until the oven racks are in

place.

Scratching, hitting, jarring or stressing the glass may weaken

its structure causing an increasedrisk of breakage at a later

date.

Leveling Legs

Be sure the range is leveled when installed.

If the range is not level, turn the leveling legs, I _

located at each corner of the range, until range

is level. _,,/J

&_ ANTI I_BRACKET

LEVELING LEG

To Replace Oven Light Bulb:

1. When oven is cool, hold bulb cover in place, then slide wire

retainer off cover. NOTE:Bulb cover will fall if not held in place

while removing wire retainer.

BULB CO VER

2. Removebulb coverand light bulb.

3. Replacewith a 40-wattappli-

ance bulb.

4. Replace bulb cover and se-

cure with wire retainer.

5. Reconnect power to range. Reset clock.

RETAINER

Convenience Outlet

(Canadian models only)

The convenience outlet is located

on the lower left side of the

backguard. Be sure appliance cords

do not rest on or near the surface

element. If the surface element is

turned on, the cord and outlet will

be damaged.

The convenience outlet circuit

breaker may trip if the small

appliance plugged into it exceeds

10 amps. To reset the circuit

breaker, press the switch located

on the lower edge of the

backguard.

CIRCUIT BREAKER

'Rt UBLE NG

For most concerns, try these first.

Part or ai{ of appliance does

not work.

C{ock, indicator words, and/or

lights operate but oven does

not heat.

Baking results are not as

expected or differ from

previous oven.

Food is not broiJing properly or

smokes excessively.

Oven wii{ not seJf=ciean.

Oven did not clean properly.

Oven door wii{ not unlock after

self=clean cycle.

There are no beeps and

no display.

• Check if oven controls have been properly set.

• Check to be sure plug is securely inserted into receptacle.

• Check or re-set circuit breaker. Check or replace fuse.

• Check power supply.

• Check ifsurface and/or oven controls have been properly set.See pgs. 10-11 & 15.

• Check if oven door is unlocked after self-clean cycle. See pg. 4.

• Check if oven isset for a delayed cook or clean program. See pgs. 15& 4.

• Check if Control Lock is activated. See pg. 14.

• Check if control isin Sabbath Mode. See pg. 28.

• Oven may be set for a Cook & Hold or delay function.

• Control Lock may have been set. See pg. 14.

o

Make sure the oven vent has not been blocked. See pg. 19 for location.

Check to make sure range is level.

Temperatures often vary between a new oven and an old one.As ovens age, the oven

temperature often "drifts" and may become hotter or cooler. See pg. 27 for

instructions on adjusting the oven temperature. Important: It is not recommended

to adjust the temperature if only one or two recipes are in question.

• Check oven rack positions. Food may be too close to element.

• Broil element was not preheated.

• Aluminum foil was incorrectly used. Never line the broiler insert with foil.

• Ovendoor was closed during broiling. Leavethe door open to the first stop position

(about 4 inches).

• Trim excess fat from meat before broiling.

• A soiled broiler pan was used.

• Voltage in house may be low.

• Check to make sure the cycle is not set for a delayed start. See pg. 4.

• Check if door is closed.

• Check if control is in Sabbath Mode. See pg. 27.

• Oven may be over 400° F.Oven temperature must be below 400° Fto program a

clean cycle.

• Longer cleaning time may be needed.

• Excessivespillovers, especially sugary and/or acidic foods, were not removed prior

to the self-clean cycle.

° Oven interior isstill hot. Allow about one hour for the oven to cool after the

completion of a self-clean cycle. The door can be opened when the LOCK indicator

word is not displayed.

• The control and door may be locked. See pg. 14.

• Oven may be in Sabbath Mode. See page 27.

8

Smoothtop surface

shows wear=

Moisture collects on oven

window or steam comes from

oven vent=

There is a strong odor or light

smoke when oven is turned on.

1.Tiny scratches or abrasions.

• Make sure cooktop and pan bottom are clean. Do not slide glass or metal pans

across top. Make sure pan bottom isnot rough. Use the recommended cleaning

agents. See page 6.

2.Metal marks.

• Do not slide metal pans across top. When cool, clean with Cooktop Cleaning Creme.

See page 6.

3. Brown streaks and specks.

• Removespills promptly. Never wipe with a soiled cloth or sponge. Make sure cooktop

and pan bottom are clean.

4.Areas with a metallic sheen.

• Mineral deposits from water and food. Use recommended cleaning agents. See page 6.

5.Pitting or flaking.

• Removesugary boilovers promptly. See page 6.

• Thisis normal when cooking foods high in moisture.

• Excessivemoisture was used when cleaning the window.

• Thisisnormal for a new range and will disappear after afew uses. Initiating a clean

cycle will "burn off" the odors more quickly.

• Turning on a ventilation fan will help remove the smoke and/or odor.

• Excessivefood soils on the oven bottom. Use a self-clean cycle.

Cooktop does not get • Surface controls may not be set properly.

hot enough. • Voltage to house may be low.

Fault Codes •

Noises may be heard.

The oven may detect a fault during programming or during operation. If a fault is

detected, the message FAULTDETECTED- PRESSPOWERTO CLEARor FAULT

DETECTED- PRESSENTERTO TRYAGAIN may appear. Follow directions in the display.

If the fault reappears or does not clear, call an authorized servicer or the toll-free number

in the display.

If the same operation is attempted before having the oven repaired, the message

FEATURENOT AVAILABLE will appear. The feature will remain inoperable until service

is obtained.

If the oven is heavily soiled, excessive fiareups may result in a fault code during cleaning.

Pressthe CANCEL pad and allow the oven to cool completely, wipe out excesssoil, then

reset the clean cycle. If the fault code reappears, contact an authorized servicer.

• The oven makes several low-level noises.You may hear the oven relays as they go on

and off. This is normal.

• As the oven heats and cools,you may hear sounds of metal parts expanding and

contracting. This is normal and will not damage your appliance.

SAb flashing and then • Oven is in Sabbath Mode. To cancel, press and hold the Setup pad for five

displayed continuously, seconds.

Cannot add another Favorite. • Favorites is full. To delete a favorite and add another, see page 25.

* Brand names for cleaning products are registered trademarks of the respective manufacturers.

** To order direct, call 1-800-JENNAIR (1-800-536-6247).

SURFACE O00K|NG

Surface Controls

Use to turn on the surface elements. An infinite choice of

heat settings is available from Low to High. The knobs can

be set on or between any of the settings.

Setting the Controls

1. Place pan on surface element.

2. Push in and turn the knob in either direction to the desired

heat setting.

• The control panel is marked to identify which A

element the knob controls. For example, the

graphic at right indicates right front element. Fro

3. There is an element indicator light on the control panel.

When any surface control knob is turned on, the light will

turn on. The light will turn off when all the surface

elements are turned off.

When a control is turned on, a glow can be seen through

the smoothtop surface. The element will cycle on and off

to maintain the preset heat setting, even on High.

4. After cooking, turn knob to OFF.Remove pan.

Suggested Heat Settings

The size and type of cookware, type

and amount of food and BTU of the Low

burner will determine where to set

the knob for cooking operations. Use 1

the settings printed around the

knobs as a guide.The following

descriptions will aid in choosing the

type setting that will give optimum 3

results:

Off

5

High

9

7

\

Hold or Warm: Food maintains a temperature above 140° F

without continuing to cook. Food is heated on a higher setting

until it reaches this temperature. Never use a hold or warm

setting to reheat cold food. Be sure knob isadjusted to

produce a consistant temperature. (Use the Low setting to

keep food warm.)

Simmer: Foodforms bubbles that barely break the surface.

Foods are between 185° Fand 200° F.A simmer setting can

also be used to steam or poach foods or continue cooking

covered foods. (Adjust the knob between High and Low to

obtain the desired simmer action.)

Slow Boil: Food forms bubbles at a moderate pace. A slow

boil setting can also be used for most frying and for

maintaining the cooking of large amounts of liquids. (Adjust

the knob between High and Low to obtain the desired boil

action.)

Boil: Liquid forms bubbles at a rapid pace. A fast boil setting

can be used to bring liquid to a boil, brown meat, stir fry,

saute, and heat oil for frying before turning to a lower setting.

The High setting is always used to bring liquids to a boil.

Once the liquid boils, always turn the control to the lowest

setting that will maintain the boil action.

Dual Element Lowo off @)High

The cooking surface is equipped

with a dual element located in the 3

left front position. To operate, push 6 8

in on the control knob and turn to

the left to control the small element, 9

or push to the right to control the High

4

large element. Low

10

Triple Element Q

(select models)

Off

The cooking surface has one triple L High

element located in the right front

position. This element can be used

for larger cooking utensils when the

triple element is chosen, or for _ _ 8

smaller pans when the single or dual

settings are chosen. To operate the

single element, push in the control High _\ 4

Low

knob and rotate to the left. To

operate the dual or triple elements,

make the selection with the rocker

switch and rotate the control knob to

the right.

(_ ©

Ultra Off Ultra

Low High

Custom Control

2

(select models)

The Custom Control Dual Element 3

offers two element sizes and is located 4 6

in the left front position. This element

uses an electronic sensor to constantly monitor and adjust

heat output for precise and consistent temperature control.

To operate, push in on the control knob and turn to the right

to control the small element, or push to the leftto control the

large element.

Warming Zone (:selectmodels)

Use the Warming Zone to keep cooked foods warm, such as

vegetables and gravies.

/

Press the Warm Zone pad to turn on the Warm

Zone

element, then press the Quickset pad for On / Off

HIGH or LOW. To turn off, press the Warm ..................

Zone pad once. An icon may light as a reminder

that the Warming Zone is in use.

Important:

• Never warm food for longer than one hour (eggs for

30 minutes:),as food quality may deteriorate.

• Do not heat cold food on the Warming Zone.

• Heat settings will vary depending on type and amount of

food. Always hold food at proper food temperatures. USDA

recommends food temperatures between 140°-170° F.

Notes:

° Use only cookware recommended as safe for oven and

cooktop use.

• Always use oven mitts when removing food from the

Warming Center as cookware will be hot.

• All foods should be covered with a lid or aluminum foil to

maintain food quality.

• Do not use plastic wrap to cover foods. Plastic may melt

on to the surface and be very difficult to clean.

Smoothtop Surface

Notes:

• Cooktop may emit light smoke and odor the first few

times the cooktop is used. This is normal.

° Smoothtop cooktops retain heat for a period of time

after the element is turned off. Turn the elements off

a few minutes before food is completely cooked and use

the retained heat to complete cooking. When the hot

surface light turns off, the cooking area will be cool

enough to touch. Because of the way they retain heat, the

smoothtop elements will not respond to changes in

settings as quickly as coil elements.

• In the event of a potential boilover, remove the pan from

the cooking surface.

• Never attempt to lift the cooktop.

• The smoothtop surface may appear discolored when it is

hot. On Frost models, the smoothtop will have a slight

pink or green tint. This is normal and will disappear when

the surface cools.

Not Surface Indicator Lights

The Hot Surface indicator lights are located next to the

elements. These lights indicate when the adjacent cooking

area is hot to the touch even after the control has been

turned off. The red light will remain on until the surface

has cooled.

Cooking Areas

The cooking areas on your range are identified by permanent

patterns on the smoothtop surface. For most efficient cooking,

fit the pan size to the element size.

Pails should not extend more than _/2to 7-inch beyond

the cooking area.

When a control is turned on, a glow can be seen through the

smoothtop surface. The element will cycle on and off to

maintain the preset heat setting, even on High.

For more information on cookware, refer to Cookware

Recommendations on page 12.

REGULAR

WARMING ZONE

REGULAR

ELEMENT

11

TRIPLE ELEMENT

(SELECT MODELS)

Tips to Protect the

Smoothtop Surface

Cleaning (see page 6 for more information:)

• Before first use, clean the cooktop.

• Clean your cooktop daily or after each use. This will keep

your cooktop looking good and can prevent damage.

• Ifaspilloveroccurswhilecooking,immediatelycleanthe

spillfromthecookingareawhileitishottopreventatough

cleaningchorelater.Usingextremecare,wipespillwitha

clean,drytowel.

• Donot allow spills to remain on the cooking area or the

cooktop trim for a long period of time.

• Never use abrasive cleansing powders or scouring pads

which will scratch the cooktop.

• Never use chlorine bleach, ammonia or other cleansers not

specifically recommended for use on glass-ceramic.

To Prevent Marks & Scratches

• Do not use glass pans. They may scratch the surface.

• Never place a trivet or wok ring between the surface and

pan. These items can mark or etch the top.

° Do not slide aluminum pans across a hot surface. The pans

may leave marks which need to be removed promptly. (See

Cleaning, page 6.]

° Make sure the surface and the pan bottom are clean before

turning on to prevent scratches.

• To prevent scratching or damage to the glass-ceramic top,

do not leave sugar, salt or fats on the cooking area. Wipe

the cooktop surface with a clean cloth or paper towel

before using.

• Never slide heavy metal pans across the surface since

these may scratch.

To Prevent Stains

• Never use a soiled dish cloth or sponge to clean the

cooktop surface. A film will remain which may cause stains

on the cooking surface after the area is heated.

• Continuously cooking on a soiled surface may/will result in

a permanent stain.

To Prevent Other Damage

• Do not allow plastic, sugar or foods with high sugar

content to melt onto the hot cooktop. Should this happen,

clean immediately. (See Cleaning, page 6._

• Never let a pan boil dry as this will damage the surface and

pan.

° Never use cooktop as a work surface or cutting board.

• Never cook food directly on the surface.

• Do not use a small pan on a large element. Not only does

this waste energy, but it can also result in spillovers burning

onto the cooking area which requires extra cleaning.

• Do not use non-fiat specialty items that are oversized or

uneven such as round-bottom woks, rippled bottom and/or

oversized canners and griddles.

• Do not use foil or foil-type containers. Foil may melt onto

the glass. If metal melts on the cooktop, do not use. Call an

authorized servicer.

Cookware Recommendations

Using the right cookware can prevent many problems, such

as food taking longer to cook or achieving inconsistent

results. Proper pans will reduce cooking times, use less

energy, and cook food more evenly.

Flat Pan Tests

To determine whether your pans are flat.

The Ruler Test:

1. Placea ruler across tile bottom of tile pan.

2. Hold it up to the light.

3. Little or no light should be visible under the ruler.

The Bubble Test:

1. Put I inchof water in tile pan. Placeon cooktop and turn

control to High.

2. Watch the formation of the bubbles as the water heats.

Uniform bubbles mean good performance, and uneven

bubbles indicatehot spots and uneven cooking.

Flat,smooth-bottom Panswith grooved or warped bottoms.

_ans. Panswith uneven bottoms do not cook

efficiently and sometimes may not

boil liquid.

Heavy-gauge pans. Very thin-gauge metal or glass pans.

Pansthat are the Panssmaller or larger than the

same size asthe element by 1inch.

element.

Secure handles. Cookware with loose or broken handles.

Heavy handles that tilt the pan.

Tight-fitting lids. Loose-fitting lids.

Flat-bottom woks. Woks with a ring-stand bottom.

Canning and Oversize Cookware

All canners and large pots must have fiat bottoms and

must be made from heavy-gauge materials. This iscritical

on smoothtop surfaces. The base must not be more than

1 inchlarger than the element.

When canners and pots do not meet these standards, cooking

times may be longer, and cooktops may be damaged.

Somecanners are designed with smaller bases for use on

smoothtop surfaces.

When canning, use the High heat setting only until the

water comes to a boil or pressure is reached in the canner.

Reduce to the lowest heat setting that maintains the boil or

pressure. If the heat is not turned down, the cooktop may be

damaged.

12

OVENCOOK=NG

Control Panel

AB CD E

J KL

F G

TIMER2

On/Off

H

2 3

ABC DEF

4 5 6

GHI JKL MNO

Warm Warm Oven

Zone Drawer Light CANCEL

On/Off On/Off

NI N 0 P

7 8 9

PQRS TIJV WXYZ

Back 0 Enter

[ space

Jock

Q

The control panel isdesigned for ease in programming. The display window shows options for each function and moves from step

to step through the programming process. Control panel features vary by model. Oven display above is programmed for a bake

operation.

!;ili!i!iE;i

Rapid Preheat

(select models:)

Convect

(select models:)

Bake

Broil

TIMER 1

Display

TIMER 2

Number Pads

Favorites

More Options

Clean

Setup

Warm Zone

Warm Drawer

OvenLight

CANCEL

Quickset pads

Useto decrease preheating time.

Usefor convection baking and roasting.

Use for baking and roasting.

Use for broiling and top browning.

Sets timer.

Displays oven functions, options and

window time of day.

Sets timer.

Use to enter time and temperature,

or to enter Favorites names.

Use to access, program or save

baking cycles.

Use to access additional features.

Use to set self-clean cycle.

Use to view or change factory

default settings.

Use to turn Warming Zone on and off.

Use to operate the Warming Drawer.

Use to turn the oven light on or off.

Cancels all operations except Timer,

Clock, Favorites, Setup and Warm

Drawer.

Use to select options in display

window (next to display window

on both sides:).

13

Quickset Pads

Quickset pads are located on each side of the display window

and are used to select the desired function or option in the

display window. To select the option or function, press the

Quickset pad next to the word.

If you need to back out of a function or option in the display,

press the Back pad. When your programming is complete,

press the Enter pad or wait four seconds and the function will

start automatically.

Up arrows indicate additional screens with additional options.

Pressthe Quickset pads next to the arrows to scroll through

the display.

Important: Four seconds after entering the function,

option, number or letter, the function will automatically be

entered. If more than 30 seconds elapse between steps in

programming, the function will be canceled and the

display will return to the previous display.

Clock

Setting the Clock:

1. Press the Setup pad.

2. Select CLOCK using the Quickset pads.

3. Select TIME.

/, .......... ......

Setup

On/Off

/

4. Enter the time using the number pads.

5. Press Enter pad.

6. Select AM or PM in 12 hour mode. (For 24 hour clock, see

page 14.:)

7. To exit the Setup mode, press Setup pad.

Cent.

Activating and canceling the clock/day

of week display:

/ .....

1. Press Setup pad. " Setup

2. Select CLOCK. On / Off /

...................... /

3. Press the arrow to scroll until DISABLE isdisplayed.

4. Select DISABLE.

5. Select TIME.

6. Select OFF to turn the clock display off, or select ON to turn

the clock display on.

7. Select OFF to turn the day of the week display off Select

ON to turn the weekday display on.

8. To exit the Setup mode, press Setup pad.

Entering the day of the week:

/ .............

1. Press Setup pad. Setup

2. Select CLOCK. On / Off

......... ./

3. Press the arrow to scroll until DAY is displayed.

4. Use Quickset arrow to scroll through the days.

5. Select day desired.

6. To exit the Setup mode, press Setup pad.

To set the clock for a 12 or 24 hour format:

The clock can be set to display time in either a 12 hour or 24

hour format.

1. Press the Setup pad. / Setup

2. Select CLOCK. ,\On / Off,

3. Use the arrow to scroll to the next screen.

4. Select 12124 HOUR.

5. Select 12 H!{ or 24 HR.

6. To exit Setup mode, press Setup pad.

Timers

Setting the Timers (Timer 1 or Timer 2):

],

2.

PressTIMER 1 or TIMER 2 pad.

Press one of the displayed times using the

Quickset pads, or press the number pads to

enter the desired time.

/ .................... \

TIMER I

...., On/Off /

Important: Each press of the displayed time choices

adds additional time. For example, pressing "10

MIN" three times provides 30 minutes on the timer

(e:3o).

3. Press Enter pad.

Changing the amount of time entered once the

Timer starts:

/ ............

1. Press the TIMER 1 or TIMER 2 pad once. J TIMER I

2. Press the displayed times on the Quickset ,, On........./ Off

pads repeatedly until the desired time is entered.

OR

3,

4. Press Enter pad.

Canceling the Timer:

1. Pressthe TIMER 1 or TIMER 2 pad twice.

If both Timers are active:

Pressthe number pads to enter the new desired time.

4:iMERi

On / Off ji

If the desired Timer is already in the foreground, press once

for edit mode and twice to cancel the Timer. If the desired

Timer is not in the foreground, follow the steps below.

1. Pressthe desired TIMER pad once. The selected Timer will

come to the foreground.

2. Pressthe TIMER pad a secondtime to access the edit

mode in order to make changes.

3. Pressing the TIMER pad a thirdtime will cancel the Timer.

Changing the Timer beeps:

The signal beeps for TIMER 1 and TIMER 2 can be changed.

The options available are two beeps every thirty seconds, two

beeps every sixty seconds or one beep only. The default

setting isone beep. /.................................

1. Pressthe Setup pad. Setup

On / Off

2. Select the arrow to scroll until TONES "..............

is displayed.

3. Select TONES.

4. Select TIMERS TONES.

5. Select the desired timer beep format (2-30 SEC,2-60 SEC

or 1 BEEP}.

6. PressSetup pad to exit Setup mode.

Locking the Control and Oven Door

The oven control and oven door can be locked to prevent

accidental programming. If an oven function is currently

being used, the control and door cannot be locked.

To lock the control and door:

Pressthe Back and Enter pads at the same time, holding for

three seconds or until CONTROL LOCKED appears in the

display.

To unlock the control and door:

Pressthe Back and Enter pads at the same time, holding for

three seconds. UNLOCKING DOORwill appear in the display

when the control and door are unlocking.

Back 0 Enter

lock

14

Baking

To set Bake: ....................

l. Press the Bake pad. Bake

\

2. Select the oven temperature using the Quickset pads.

OR

Enter the desired temperature using the number pads.

Press Enter pad to set.

• The temperature can be set from 170° Fto 550° F

in 5° increments.

° After three seconds, the oven will begin to preheat.

BAKE and PREHEATwill appear in the display along

with 100° or the actual oven temperature, whichever

ishigher.

• The temperature in the display will increasein 1°

increments until the oven reaches the preset

temperature. Allow about 15 minutes for the oven

to preheat.

• When the oven is preheated, the oven will beep and

PREHEATwill no longer be displayed.

3. At the end of cooking, turn the oven off by

pressing the CANCEL pad. Remove food : CANCEL

from the oven. The oven will continue

operating until the CANCEL pad is pressed.

Notes:

° If more than thirty seconds elapse between pressing a

pad and pressing a number pad, the display will return

to the previous display.

• Whenever the temperature appears in the display, the

oven is heating, or heated.

° To change the oven temperature during cooking, press

the Bake pad and select a displayed temperature or use

the number pads to enter the desired temperature.

° The oven will automatically shut off after 12 hours if it is

accidentally left on. To set a Sabbath Mode, see Sabbath

Mode, page 27.

When using Delay,the oven begins to cook later in the day.

Set the amount of time that you want to delay before the oven

turns on and how long you want to cook. The oven begins to

heat at the selected time and cooks for the specified length of

time. When that time has elapsed, the oven will keep the food

warm for up to an hour then automatically turn off.

To set Cook & Hold (select models]:

1. After Bake has been programmed, press /More"

the More Options pad. ODtiOnSj

2. Select COOK/NLD. ..........

3. Select the amount of time you want to bake by pressing

the Quickset pads or the number pads.

4. Press the Enter pad.

5. COOKTIME, the cook time countdown, PREHEAT,BAKE

and the actual temperature will be displayed.

The oven will cook for the selected time, then keep food warm

for one hour.

To set a Delay:

1. After Bake has been programmed, press

the Mare Options pad.

2. Select BELAY.

3.

4.

5.

6.

/M0re,

Options/

Select the amount of time you want to delay the start of

cooking using the displayed times or the number pads.

Select the amount of time you want to cook using the

displayed times or the number pads.

The display will show BAKE,the temperature, the delay

time and the cook time countdown.

When the delay time has expired, the oven will begin

heating. COOKTIME, the cook time countdown, PREHEAT,

BAKEand the actual oven temperature will be displayed.

Bake Options

Cook & Hold (select models] and Delay options are available

when baking. When using the Cook & Hold option (select

models], the oven begins to heat immediately after the control

has been set. Then, the oven cooks for a specified length of

time. When that time has elapsed, the oven will automatically

reduce temperature to 170° F,keep the food warm for up to

an hour and then automatically turn off.

15

Oonvect (select models)

Convection uses a fan to circulate hot air evenly over, under

and around the food. As a result, foods are evenly cooked

and browned, often in shorter times, at lower temperatures

and with the flexibility of using more than one rack at a time.

Notes:

• The oven control comes from the factory set for Auto

Convect Conversion. When using Convect Bake and

Convect Pastry enter the conventional baking

temperature. The control automatically converts the

temperature to 25° less than the conventional

temperature.

• When using Convect Roast the temperature will not be

automatically reduced. Enter the conventional roasting

temperature and time. The control then lets you know

when 750/0of the time has elapsed and alerts you to

check the food for doneness.

• To turn Auto Convect Conversion off, see page 27.

Convect Options

Cook & Hold and Delay options are available when convect

cooking. See page 15for information on how to program a

Cook & Hold or Delay option.

Multiple-Rack

Baking of

Cookies/Biscuits

Breads

Casseroles

Tarts/Tortes

Cakes

Whole Chicken

Whole Turkey

Vegetables

Pork Roasts

Beef Roasts

FrozenPie

Turnovers

Cream Puffs

Puff Pastry

Notes-"

• When using Convect Bake and Convect Pastry with the

Auto Convect Conversion option turned off, reduce the

set temperature by 25° F.

• If Convect Roasting with the Auto Convect Conversion

option turned off, you will not be required to program a

cooking time. Check food at 750/0of the conventional

time.

Oonvect Bake (select models)

To set Convect Bake:

1. Press the Convect pad.

2. Select CNVT BAKE using the Quickset pads.

3. Select the oven temperature using the Quickset pads

OR

Enter the desired temperature using the number pads.

Press Enter pad to set.

• The temperature can be set from 195° Fto 550° F

degrees in 5° increments when Auto convect is on. If

Auto Convect is off, temperature can be set from 170°.

• After three seconds, the oven will begin to preheat.

CNVT BAKEand PREHEATwill appear in the display

along with 100° or the actual oven temperature,

whichever is higher.

• The temperature in the display will increase in 1°

increments until the oven reaches the preset

temperature. Allow about 15 minutes for the oven

to preheat.

• When the oven is preheated, the oven will beep,

PREHEATwill turn off and CNVT BAKE will be displayed.

AUTO will be displayed if Auto Convect Conversion

feature is turned on.

• Placefood in the oven. J............. ,

4. At the end of cooking, turn the oven off by ( CANCEL i

\ /

pressing the CANCEL pad. Remove food

from the oven. The oven will continue operating until the

CANCEL pad is pressed.

Rapid Preheat (selectmodels)

Use to decrease preheating time when using Bake or Convect

Bake. Use for all foods when baking on one rack.

• After Bake or Convect Bake has been programmed and

activated, press the Rapid Preheat pad.

• 1 RACK ONLY will display, after 10 seconds the display will

show RAPIDand PREHEAT.

• Preheat time is five minutes.

To return to Standard Preheat:

Press Rapid Preheat pad again. This will provide standard

preheat and PREHEATand the selected function will be

displayed.

Notes:

For best results, use rack position 3 or 4 when using the

Rapid Preheat option.

For optimum baking and browning results, Rapid Preheat

is not recommended when baking on multiple racks.

16

CORVeCt Roast (select models)

To set Convect Roast:

1. Place food in the oven.

2. Press the Convect pad. J....................

/ Convect

3. Select CNVT ROAST using the ", .......

Quickset pads.

Convect Pastry (selectmodels)

Convect Pastry isdesigned to bake pastry itemssuch as

frozen pies, turnovers, cream puffs and puff pastry. Use one,

two or three racks while using this feature.

1. Press the Convect pad. ( Convect )

2. Select CNVT PASTRY using the

Quickset pads.

4. Select the oven temperature using the Quickset pads.

OR

Enter the desired temperature using the number pads.

Press Enter pad to set.

• The temperature can be set from 170° Fto 550° F

degrees in 5° increments.

5. Enter desired cook time. Enter the conventionalroasting

time using the number pads.

• After three seconds, the oven will begin to heat. CNVT

ROASTwill appear in the display along with 100° or the

actual oven temperature, whichever is higher.

° The temperature in the display will increase in 1°

increments until the oven reaches the preset

temperature.

• Cook time will begin to count down.

6. At 750/0of the cooking time the oven will beep to let

you know to check food. Check food using a meat

thermometer. If food is done, take food out of oven and

press CANCEL pad to turn oven off.

7. If food is not done, continue roasting.

Once the set time has elapsed the oven will automatically

go into Keep Warm mode for 1 hour and then shut off. If

food istaken from the oven before the _............

hour has elapsed, press the CANCEL pad. (,CANCEL

3. Select the oven temperature using the Quickset pads.

OR

Enter the desired temperature using the number pads.

Press Enter pad to set.

° The temperature can be set from 195° Fto 550° F

degrees in 5° increments.

° After three seconds, the oven will begin to preheat.

CNVT PASTRYand PREHEATwill appear in the display

along with 100° or the actual oven temperature, which

ever is higher. AUTO will display if the Auto Convect

Conversion feature is turned on.

° The temperature in the display will increase in 1°

incrementsuntil the oven reaches the preset

temperature. Allow about 15 minutes for the oven to

preheat.

• When the oven ispreheated, the oven will beep,

PREHEATwill turn off and CNVT PASTRYwill be

displayed.

4. At the end of cooking, turn the oven off by / ...............................

pressing the CANCEL pad. Removefood CANCEL i'

from the oven. The oven will continue ......................

operating until the CANCEL pad is pressed.

Notes:

• if the recipe suggests preheating the oven, add 15

minutes to cook time.

° If Auto Convect isoff, roast time will not be required.

17

Warming Drawer

Tile Warming Drawer isused for keeping hot foods at serving

temperature. It may also be used for warming breads and

pastries.

Operating the Controls:

1. Press the Warm Drawer pad to turn on.

2.Select HIGH or LOW.

3. Allow the drawer to preheat for ten minutes.

4. Place food inwarming drawer.

/warm

j

Drawer

,\ On/Off

5. When finished, press the Warm Drawer pad to turn off.

Remove food from the drawer.

Warming Chart

Broil

Foroptimal results, preheat for five minutes with the door

closed and use a pan designed for broiling.

To set Broil:

1. Place the oven rack in the proper rack position (see

Broiling Chart, page 19:).

2. Press the Broil pad.

3. Select HIGH - 550° Ffor high broil.

oR , Broil

Select LOW - 450° Ffor low broil.

HIGH Bacon Beef- Rare

Casseroles Cooked Cereals

Dinner Plate Eggs

Enchiladas Fish/Seafood

Fried Food Gravy, Cream Sauces

Ham Hamburger Patties

Hors d'oeuvres Lamb

Pancakes Pizza

Pork Potatoes - Baked

Potatoes - Mashed Poultry

Vegetables Waffles

LOW Biscuits Coffee Cake

Pies Warming - Plates

Notes:

• Do not warm food for more than one hour (eggs

30 minutes:) after cooking.

• Food must be at serving temperature before being

placed in the drawer.

, Breads, pastries and fruit pies may be warmed from

room temperature at the HIGHsetting.

, Use only oven-safe cookware.

, Removefood from plastic bags and place in oven-safe

cookware.

• Serving dishes and plates can be warmed while

preheating the drawer on Low.

• Cover food with a lid or aluminum foil. Do not use

plastic wrap. (Fried foods do not need to be covered.:)

4,

5.

° The oven has a variable broil feature which means that

a lower broil temperature can be selected (3000-550° F:).

To select a lower temperature, press the appropriate

number pads. Press Enter pad to set the lower

temperature.

Preheat the oven for five minutes.

Placefood in the oven and close the door to the broil stop

position.

Pressthe CANCEL pad when broiling (CANCEL

is done. , /

Notes:

° SeeBroiling Chart, page 19,for foods and broiling times.

• If more than 30 seconds elapse between pressing the

Broil pad, Quickset pads, or number pads, the oven will

not be set and the display will return to the previous

display.

• HIGH is used for most broiling. Use a lower broil

temperature when broiling longer-cooking foods. The

lower temperature allows food to cook to the well done

stage without excessive browning.

, Expect broil times to increase and browning to be

slightly lighter if the appliance is installed on a 208 volt

circuit.

• Food should be turned halfway through broiling time.

• Broil times may be longer when lower broiling

temperatures are selected.

Cont.

18

Broiling Chart

Beef

Steak, 1" thick,

Hamburgers, 3/4" thick,

Pork

Bacon

Chops, 1"

Ham Slice

Medium

Well

6

6or7

8 minutes

10 minutes

5-9 minutes

6 - 10 minutes

7 - 12 minutes

8 - 14 minutes

6 - 9 minutes

(no turning)

10 - 11 minutes

5 minutes

12 - 14 minutes

3 - 7 minutes

Poultry LO Broil LO Broil

Breast Halves 4 15 minutes 15 - 25 minutes

Seafood

Fish Steaks, buttered, 1" thick

Lobster Tails, 3-4 oz. each

10 - 15 minutes

7 - 10 minutes

Note: This chart isa suggested guide. The times may vary with the food being cooked.

(no turning)

Oven Fan

A convection fan (select models) is used to circulate hot air in

the oven when the convection feature is selected.

Important: The convection fan will automatically stop when

the oven door is opened.

Oven Racks

Oven Vent

The oven vent is located along the back edge of the cooking

surface.

When the oven is in use, the area near the oven vent may

become hot enough to cause burns. For best baking results,

do not block the vent opening.

Oven Light

The oven light automatically comes on when

the door isopened. When the door isclosed,

Light

press the Oven Light pad to turn the oven

light on and off. A beep will sound every time

the Oven Light pad is pressed. If the oven light is on when the

door is opened, the light will go off when the door is closed.

Oven Bottom

Protect oven bottom against spillovers, especially acidic or

sugary spills, as they may discolor the porcelain enamel. Use

the correct pan size to avoid spillovers and boilovers. Do not

place utensils or aluminum foil directly on the oven

bottom.

The oven has two racks (three if convection, select models).

All racks are designed with a lock-stop edge.

To remove:

1. Pull forward to the "stop"

position.

2. Lift up on the front of the

rack and pull out.

To replace:

1. Place rack on the rack

support in the oven.

2.

3.

Tilt the front end up slightly; slide rack back until it clears

the lock-stop position.

Lower front and slide into the oven.

19

La page charge ...

Jenn-Air JER8885RAB Le manuel du propriétaire

Jenn-Air JER8885RAB Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents