AT&T CRL30102 Manuel utilisateur

Marque: AT&T

Modèle: CRL30102

Catégorie: Téléphones

Taper: Manuel utilisateur

User’s manual

CRL30102

DECT 6.0 expansion handset

for use with AT&T models

CRL32102/CRL32202/CRL32302/

CRL32352/CRL32452

Congratulations

on your purchase of this AT&T product. Before using this AT&T

product, please read the Important safety information section

on pages 20-22 of this manual. For complete instructions, please

refer to the manual provided with your CRL32102/CRL32202/

CRL32302/CRL32352/CRL32452 telephone. You can also visit our

website at www.telephones.att.com or call

1 (800) 222-3111. In Canada, dial 1 (866) 288-4268.

This telephone meets the California Energy Commission

regulations for energy consumption. Your telephone is set up to

comply with the energy-conserving standards right out of the box.

No further action is necessary.

Model number:

CRL30102

Type: DECT 6.0 expansion handset

Serial number: _______________________________________________

Purchase date: _______________________________________________

Place of purchase: _____________________________________________

Both the model and serial numbers of your AT&T product can be

found on the bottom of the telephone base.

Save your sales receipt and original packaging in case it is

necessary to return your telephone for warranty service.

Telephones identied with this logo have reduced noise and

interference when used with most T-coil equipped hearing aids and

cochlear implants. The TIA-1083 Compliant Logo is a trademark of

the Telecommunications Industry Association. Used under license.

the AT&T logo are trademarks of AT&T Intellectual Property licensed to

Advanced American Telephones, San Antonio, TX 78219. Printed in China.

Parts checklist

Your telephone package contains the following items. Save your

sales receipt and original packaging in the event warranty service

is necessary.

Battery for

cordless handset

Cordless handset

Charger for cordless

handset with power

adapter installed

Battery

compartment cover

User’s manual

CL80103

DECT 6.0 expansion handset

for use with AT&T models

CRL32102/CRL32202/CRL32302/

CRL32352/CRL32452

Battery Pack / Bloc-piles :

BT183342/BT283342 (2.4V 400mAh Ni-MH)

WARNING / AVERTISSEMENT :

DO NOT BURN OR PUNCTURE BATTERIES.

NE PAS INCINÉRER OU PERCER LES PILES.

Made in China / Fabriqué en chine CR0920

THIS SIDE UP / CE CÔTÉ VERS LE HAUT

User’s manual

CRL30102

DECT 6.0 expansion handset

for use with AT&T models

CRL32102/CRL32202/CRL32302/CRL32352/

CRL32452

Getting started

Installation ..............................................1

Quick reference guide -

handset .................................................... 2

Charger installation ......................... 5

Battery installation and

charging ...................................................6

Registration and

deregistration

Adding and registering

handsets ..................................................8

telephone base ..............................8

Deregistering handsets ..............10

Deregister all handsets from

your telephone base ................. 10

Appendix

Troubleshooting................................11

Maintenance .......................................19

Important safety

information............................................20

Safety information .....................20

Especially about cordless

telephones ........................................21

Precautions for users of

implanted cardiac

pacemakers .................................... 22

Pacemaker patients .................. 22

Especially about telephone

answering systems ....................22

For C-UL compliance .....................23

Mesures de sécurité

importantes ....................................23

FCC Part 68 and ACTA ..................26

FCC Part 15 .......................................... 28

California Energy Commission

battery charging testing

instructions ..............................................29

Limited warranty ............................ 30

Technical specications ..............33

DECT 6.0 digital technology ....

Telephone operating range ...33

Redening long range

coverage and clarity ................. 33

HD audio ............................................ 33

Table of contents

See pages 6-7

for easy instructions.

You must install and

charge the battery before

using the telephone.

STOP!

Installation

Your product may be shipped with a protective sticker covering the

handset display - remove it before use.

For customer service or product information, visit our website at

www.telephones.att.com or call 1 (800) 222-3111.

In Canada, dial 1 (866) 288-4268.

Avoid placing the telephone base too close to:

Communication devices such as television sets, VCRs, or other

cordless telephones.

Excessive heat sources.

Noise sources such as a window with trac outside, motors,

microwave ovens, refrigerators, or uorescent lighting.

Excessive dust sources such as a workshop or garage.

Excessive moisture.

Extremely low temperature.

Mechanical vibration or shock such as on top of a washing

machine or workbench.

•

Getting started

Quick reference guide - handset

Getting started

Incoming call light

Flashes when there is an incoming call or

when the base is paging the handset.

CHARGE indicator

On when the handset is charging in the

telephone base or charger.

REDIAL/PAUSE

Press repeatedly to view the last 10 numbers

dialed.

While saving numbers into the directory,

press and hold

to insert a dialing pause.

PHONE/FLASH

Press to make or answer a call.

During a call, press to answer an incoming call

when you receive a call waiting alert.

qCID/VOLUME

Press qCID to show the caller ID log.

Press to scroll down while in menus.

While entering names or numbers, press to

move the cursor to the le.

Press to decrease the listening volume

when on a call, or to decrease the message

playback volume.

While reviewing a caller ID log entry, press

repeatedly to add or remove 1 in front of the

telephone number before dialing or saving it

in the directory.

Press and hold to set or dial your voicemail

number when the handset is not in use.

/SPEAKER

Press to switch between the speakerphone

and the handset.

TONE

Press to switch to touch-tone dialing

temporarily during a call if you have pulse

service.

Quick reference guide - handset

Getting started

MUTE/DELETE

During a call, press to mute the microphone.

While reviewing the caller ID log, the directory

or the redial memory, press to delete an

individual entry.

While predialing, press to delete digits.

While editing numbers or names in the

directory, press to delete digits or characters,

or press and hold to delete all digits or

characters.

QUIET

(pound key)

Press repeatedly to display other dialing

options when reviewing a caller ID log entry.

Press and hold to enter the QUIET mode setting

screen, or to deactivate QUIET mode.

OFF/CANCEL

During a call, press to hang up.

While in menus, press to cancel an operation,

back up to the previous menu, or exit the

menu display; or press and hold this key to

exit to idle mode.

Press and hold while the telephone is not in use

to erase the missed call indicator.

MENU/SELECT

Press to show the menu.

While in the menu, press to select an item or

save an entry or setting.

pDIR/VOLUME

Press pDIR to show directory entries.

Press to scroll up while in menus.

While entering names or numbers, press to

move the cursor to the right.

Press to increase the listening volume when

on a call, or to increase the message playback

volume.

AUDIO ASSIST

During a call, press to enhance the clarity and

loudness of your caller’s voice.

Audio Assist is a registered trademark of Advanced American Telephones.

Quick reference guide - handset

Getting started

Main menu

Play messages

Answering sys

Directory

Caller ID log

Intercom

Ringers

Set date/time

Settings

Web address

•

Using menus:

Press MENU/SELECT to show the menu.

Press qCID or pDIR to scroll through menu items.

Press MENU/SELECT to conrm or save changes to a highlighted

menu item.

Press OFF/CANCEL to cancel an operation, back up to the

previous menu, or exit the menu display.

•

For complete instructions, refer to the manual provided with

your CRL32102/CRL32202/CRL32302/CRL32352/CRL32452

telephone system.

If you are unable to nd your manual, go to

www.telephones.att.com/manuals to read and/or

download the manual.

Handset

side view

During an outside call, intercom call, message or

announcement playback, press to change the

quality of the audio to best suit your hearing.

The > symbol highlights

a menu item.

>Play messages

Answering sys

IMPORTANT INFORMATION

1. Use only the power adapter supplied with this product. To order a replacement

power adapter, visit our website at www.telephones.att.com or

call 1 (800) 222-3111. In Canada, dial 1 (866) 288-4268.

2. The power adapter is intended to be correctly oriented in a vertical or oor

mount position. The prongs are not designed to hold the plug in place if it is

plugged into a ceiling, under-the-table or cabinet outlet.

Plug the power adapter into an

electrical outlet not controlled by a

wall switch.

Charger installation

Install the charger, as shown below.

Getting started

Battery installation and charging

Install the battery, as shown on page 7. Once you have installed the

battery, the screen indicates the battery status (see the following

table). If necessary, place the handset in the telephone base or

charger to charge the battery. For best performance, keep the

handset in the telephone base or charger when not in use. The

battery is fully charged aer 10 hours of continuous charging. See

the table on page 33 for battery operating times.

If the screen shows Place in charger and ashes, you need to

charge the handset without interruption for at least 30 minutes to

give the handset enough charge to use the telephone for a short

time. The following table summarizes the battery charge indicators

and actions to take.

Getting started

Battery indicators Battery status Action

The screen is blank, or

shows Place in

charger and

(ashing).

Battery has no or

very little charge. The

handset cannot be used.

Charge without interruption

(at least 30 minutes).

The screen shows

Low battery and

(ashing).

Battery has enough

charge to be used for a

short time.

Charge without interruption

(at least 30 minutes).

The screen shows

HANDSET X.

Battery is charged. To keep the battery

charged, place it in the

telephone base or charger

when not in use.

NOTE: If you are on a phone call in low battery mode, you hear four short beeps

every minute.

Battery installation and charging

Getting started

Step 1

Plug the battery connector securely into the socket inside the

handset battery compartment. Insert the supplied battery with the

label THIS SIDE UP facing up, as indicated.

Step 2

Align the cover at against the battery compartment, then slide it

upwards until it clicks into place.

Step 3

Charge the handset by placing it face

forward in the telephone base or charger.

The CHARGE light on the top of the

handset is on during charging.

IMPORTANT INFORMATION

1. Use only the supplied rechargeable battery or replacement battery

(model BT183342/BT283342). To order, visit our website at

www.telephones.att.com or call 1 (800) 222-3111.

In Canada, dial 1 (866) 288-4268.

2. If you do not use the handset for a long time, disconnect and remove

the battery to prevent possible leakage.

UDI

/ CE

CÔ

y Pa

/ Bl

BT18

-M

)

ENT

ES.

ÉR

U PER

CER

S PI

UDI

CHARGE light

Adding and registering handsets

Before using a new CRL30102 handset, you must register it with

the AT&T CRL32102/CRL32202/CRL32302/CRL32352/CRL32452

telephone system (purchased separately). The telephone system

can support up to 12 handsets.

The handsets provided with your telephone system are already

registered as HANDSET 1, and so forth. Additional handsets

registered to the telephone system are assigned in sequential

order they are registered (up to HANDSET 12).

You must register each handset separately. When rst purchased, all

expansion handsets show To register HS, see manual..

1. Before you begin registration, make sure the

handset is out of the telephone base or charger

and shows To register HS, see manual..

2. Put the handset you wish to register on the

telephone base cradle.

Registration and deregistration

To register HS,

see manual.

For registration, put the handset

on the telephone base, not the

handset charger.

Adding and registering handsets

3. The screen shows Registering... Please wait

and the IN USE light turns on. It takes up to 90

seconds to complete registration. Then,

HANDSET X Registered appears on the screen,

with X being the handset number (1-12). The

handset beeps and the IN USE light turns o. The

handset is now registered with the telephone

base.

If registration fails, the system will automatically try

to register again. If registration fails aer the third

try, Registration failed appears on the screen for a few seconds, and

then To register HS, see manual.. This may take up to ve minutes to

occur. Please start again from Step 1.

NOTE: You cannot register a handset if any other system handset is in use..

Registration and deregistration

Registering...

Please wait

10/20

10:30

HANDSET X

Registered

Registration and deregistration

Deregistering handsets

You may need to deregister your handsets if:

You have 12 registered handsets and need to replace a handset.

-OR-

You wish to change the designated handset number of your

registered handsets.

You must rst deregister ALL the handsets, and then register each

handset you wish to use again, one at a time.

Please read carefully through all the instructions on this page

before beginning the deregistration process.

Deregister all handsets from your telephone base

1. Make sure that all handsets are out of the telephone base and

chargers before you begin deregistration.

Press and hold /HANDSET LOCATOR on the telephone base

for about 10 seconds (until the IN USE light starts to ash), then

release the /HANDSET LOCATOR button.

3. Immediately press

/HANDSET LOCATOR again while the

IN USE light is still ashing. (The light ashes for about seven

seconds. If the light stops ashing, start again with Step 1.)

4. It takes up to 10 seconds to complete deregistration. Wait for the

cordless handset screen to display To register HS, see manual..

5. To register the handset(s) to the telephone base again, follow the

instructions on pages 8-9.

NOTES:

If the deregistration process is not successful, you might need to reset the system

and try again. To reset, unplug the power from the telephone base and plug it back in.

You cannot deregister the handset(s) if any other system handset is in use.

Even if the battery is depleted, you can still deregister the handset by following the

steps mentioned above. After the handset is charged for at least 10 minutes, the

screen shows To register HS, see manual..

•

Troubleshooting

If you have diculty with your phone, please try the following

suggestions. For Customer Service, visit our website at

www.telephones.att.com or call 1 (800) 222-3111.

In Canada, dial 1 (866) 288-4268.

The handset registration is unsuccessful.

Follow the handset registration instructions to register the handset

again (see Adding and registering handsets on pages 8-9).

My telephone doesn’t work at all.

Make sure the power cord is securely plugged in.

Make sure you plug the battery connector securely into the

cordless handset.

Make sure you plug the telephone line cord securely and rmly

into the telephone base and the telephone wall jack.

Charge the battery in the cordless handset for at least 10 hours.

For optimum daily performance, return the cordless handset to

the telephone base or charger when not in use.

If the battery is depleted, it might take approximately 30 minutes

to charge the handset before it shows Low battery. See page 6

for details.

Reset the telephone base. Unplug the electrical power. Wait for

approximately 15 seconds, then plug it back in. Allow up to one

minute for the cordless handset and telephone base to reset.

You may need to purchase a new battery. Refer to Battery

installation and charging in this user’s manual on pages 6-7.

The display shows No line. I cannot get a dial tone.

Try all the suggestions mentioned above.

If the previous suggestions do not work, disconnect the

telephone line cord from your telephone and connect the

telephone line cord to another telephone.

If there is no dial tone on that other telephone either, your

telephone line cord may be defective. Install a new telephone

line cord.

•

Appendix

Troubleshooting

Appendix

If changing the telephone line cord does not help, the wall jack

(or the wiring to this wall jack) may be defective. Try using a

dierent wall jack in your home to connect your CRL32102/

CRL32202/CRL32302/CRL32352/CRL32452 telephone, or

contact your telephone service provider (charges may apply).

I cannot dial out.

Try all the suggestions mentioned above.

Make sure you have a dial tone before dialing. The cordless

handset might take a second or two to nd the telephone base

and produce a dial tone. This is normal. Wait an extra second

before dialing.

Eliminate any background noise. Noise from a television, radio or

other appliances might cause the phone to not dial out properly.

If you cannot eliminate the background noise, try muting the

cordless handset before dialing, or dialing from another room

with less background noise.

If other phones in your home are having the same problem,

contact your telephone service provider (charges might apply).

My cordless handset isn’t performing normally.

Make sure you plug the power cord securely into the telephone

base. Plug the power adapter into a dierent, working electrical

outlet without a wall switch.

Move the cordless handset closer to the telephone base. You

might have moved out of range.

Reset the telephone base. Unplug the electrical power. Wait for

15 seconds, then plug it back in. Allow up to one minute for the

cordless handset and telephone base to reset.

Other electronic products such as HAM radios and other DECT

phones, can cause interference with your cordless phone. Try

installing your phone as far away as possible from these types of

electronic devices.

•

Troubleshooting

Appendix

Out of range OR No pwr at base appears on my cordless handset.

Ensure you plug the telephone base in properly and the power is

on.

Place the cordless handset in the telephone base for one minute

to allow the cordless handset and base to synchronize.

Move the cordless handset closer to the telephone base. You

might have moved out of range.

Reset the telephone base. Unplug the electrical power. Wait for

15 seconds, then plug it back in. Allow up to one minute for the

cordless handset and telephone base to reset.

Other electronic products such as HAM radios and other DECT

phones, can cause interference with your cordless phone. Try

installing your phone as far away as possible from these types of

electronic devices.

The batteries do not hold a charge.

If the cordless handset is in the telephone base or charger

and the charge light is not on, refer to The charge light is o

(page 18) in this Troubleshooting guide.

Charge the battery in the cordless handset for at least 10 hours.

For optimum daily performance, return the cordless handset to

the telephone base or charger when not in use.

If the battery is depleted, it might take approximately 30 minutes to

charge the handset before it shows Low battery. Refer to the table

on page 6 for details.

You might need to purchase a new battery. Refer to Battery

installation and charging in this user’s manual on pages 6-7.

I hear other calls while using my phone.

Disconnect the telephone base from the telephone jack, and

plug in a different telephone. If you still hear other calls, call

your telephone service provider.

•

I get noise, static, or weak signals even when I’m near the

telephone base.

If you subscribe to high-speed Internet service (DSL - digital

subscriber line) through your telephone line, you must install a

DSL lter between the telephone line cord and the telephone

wall jack. The lter prevents noise and caller ID problems as

a result of DSL interference. Please contact your DSL service

provider for more information about DSL lters.

You may be able to improve the performance of your cordless

phone by installing your new telephone base as far as possible

from any other existing cordless telephone system that may

already be installed.

Other electronic products such as HAM radios and other DECT

phones, can cause interference with your cordless phone. Try

installing your phone as far away as possible from these types of

electronic devices.

Do not install this phone near a microwave oven or on the same

electrical outlet. You might experience decreased performance

while the microwave oven is operating.

If you plug your phone in with a modem or a surge protector,

plug the phone (or modem/surge protector) into a dierent

location. If this does not solve the problem, relocate your phone

or modem farther apart from one another, or use a dierent

surge protector.

Move your phone to a higher location. The phone might have

better reception in a high area.

If the other phones in your home are having the same problem,

contact your telephone service provider (charges may apply).

I experience poor sound quality when using the speakerphone.

For increased sound quality while using the speakerphone, place

the handset on a at surface with the dialing keys facing up.

•

Troubleshooting

Appendix

My cordless handset does not ring when I receive a call.

Make sure that the ringer is not o. Refer to Ringer volume

in the user’s manual provided with your CL82203/CL82303/

CL82353/CL82403/CL82453/CL82553/CL83203/CL83303/CL83403

telephone.

Make sure you plug the telephone line cord securely into the

telephone base and telephone jack. Make sure you plug in the

power cord securely.

The cordless handset may be too far from the telephone base.

Charge the battery in the cordless handset for at least 10 hours.

For optimum daily performance, return the cordless handset to

the telephone base or charger when not in use.

You may have too many extension phones on your telephone

line to allow all of them to ring simultaneously. Try unplugging

some of the other phones.

The layout of your home or oce might be limiting the

operating range. Try moving the telephone base to another

location, preferably on an upper oor.

If the other phones in your home are having the same problem,

contact your telephone service provider (charges might apply).

Test a working phone at the phone jack. If another phone has

the same problem, contact your telephone service provider

(charges might apply).

Other electronic products such as HAM radios and other DECT

phones, can cause interference with your cordless phone. Try

installing your phone as far away as possible from these types of

electronic devices.

Completely remove the battery. Replace it and place the

cordless handset into the telephone base. Allow up to one

minute for the handset to reestablish its connection with the

telephone base.

Your line cord might be defective. Try installing a new line cord.

•

Troubleshooting

Appendix

Troubleshooting

Appendix

My calls cut in and out while I’m using my cordless handset.

Other electronic products such as HAM radios and other DECT

phones, can cause interference with your cordless phone. Try

installing your phone as far away as possible from these types of

electronic devices.

Do not install this phone near a microwave oven or on the same

electrical outlet. You might experience decreased performance

while the microwave oven is operating.

If you plug your phone in with a modem or surge protector, try

plugging the phone (or modem/surge protector) into a dierent

location. If this does not solve the problem, relocate your phone

or modem farther apart from one another, or use a dierent

surge protector.

Move your telephone base to a higher location. The phone

might have better reception when installed in a high area.

If other phones in your home are having the same problem,

contact your telephone service provider (charges may apply).

My caller ID isn’t working.

Caller ID is a subscription service. You must subscribe to this

service from your telephone service provider for this feature to

work on your phone.

The caller may not be calling from an area that supports caller ID.

Both your and your caller’s telephone service providers must

use caller ID compatible equipment.

If you subscribe to high-speed Internet service (DSL - digital

subscriber line) through your telephone line, you must install a

DSL lter between the telephone line cord and the telephone

wall jack. The lter prevents noise and caller ID problems

resulting from DSL interference. Contact your DSL service

provider for more information about DSL lters.

•

La page charge ...

AT&T CRL30102 Manuel utilisateur

Marque: AT&T

Modèle: CRL30102

Catégorie: Téléphones

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: AT&T CRL30102 User manual

AT&T CRL30102 Manuel utilisateur

AT&T CRL30102 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents