R03.002_27/04/2016
TECHNICAL FILE
Novolistel® 4 Aluminium
Novolistel® 4 is a modern listello from the range of decorative
listellos of Emac®. Its wide visible side makes it a main element
on the environments where is installed. It is available in natural
color, anodized matt silver or bright silver and the exclusive and an
original lacquered color: wengue. The anodized nishes are suitable
to be installed outdoors.
Technical Features
Applications
Complementary pieces
Novolistel® 4 is a decorative listello for indoors and outdoors in case of anodized nishes.
This listello can be installed vertically or horizontally and threir applications are the following:
Novolistel® 4 Aluminium has a complementary piece available to get a perfect nish.
Model registered as community design
Nº 0504253-0008(4)
Exterior angle. Not available in all the nishes
Technical Features
Page 1 of 4
- As listello.
- As corner protection.
- As ooring separation.
- As stair nosing or worktop nish.
Material:
Anodized aluminium
Lacquered aluminium
Lenght: 8ft2in / 2.5 l.m.
Dimensions: h: 3/8” /10 mm.
h: 1/2” / 12 mm.
a: 1” / 25 mm.
Packaging: 30 u./box
With protective lm.
Finishes:
Alloy: 6063 (AA and ASTM)
L-3441 (UNE 38-301-89)
Fire resistance: M0 (UNE 23-727-90)
Abrasion resistance: Very good
Lightfastness: Excellent
Appearance and color: EN 12373-1
* *
R03.002_27/04/2016
TECHNICAL FILE
Novolistel® 4 Aluminium is a prole made by extrusion of aluminium. The matte silver and mirror
bright nishes have been anodized, improving mainly through this process their corrosion resistance,
mechanical resistance and appearance. The anodized applied has the quality seal Qualanod, which
guarantees the quality of the process and the resulting proles. This seal regulates several tests:
appearance and color, thickness measurements, sealing and impregnation control, abrasion resistance,
lightfastness, acetic saline chamber and nitric acid immersion.
The jupiter silver, jupiter black and wengue nishes have been lacquered, obtaining so a high quality
and homogeneus surface. The lacquering has the quality seal Qualicoat, which guarantees the quality
of the process and the nal products.
The aluminium is a material with excellent chemical, physical and mechanical properties. It is lightweight,
tough, ductile, malleable and highly durable.
*You can amplify information by consulting the Technical Files of the materials in www.emac.es
1. Spread a big amount of gripping material on the surface to be tiled and tile it up to the approxima-
ted height where you’ll place the listello.
2. Place the tiles in the end of the next row, aligning them with previous tiles. Then place the prole
aligned to them, embedding the xing wing between the wall and the tiles. Press to ensure the
gripping material to pass through the mechanized holes of the xing wing.
3. Place the remaining tiles, pressing softly to achieve an optimal adhesion.
4. Then, continue tiling the wall up to the desired height.
5. Finally, clean the remaining material, remove the protective lm if necessary and let dry.
1. Spread a big amount of gripping material on the surface where you are going to place the prole.
2. Place the prole aligned to the corner and press to make the gripping material pass through the
mechanized holes of the xing wing.
3. Place tiles on the xing wing and press to an optimal adhesion.
4. Continue the wall tiling.
5. Finally, clean the remaining material, remove the protective lm if necessary and let dry.
Aluminium
As listello
As edge protector
Materials
Placement
1
1 2 3 4 5
2
3
4
Page 2 of 4
Novolistel® 4 Aluminium
To see the video, capture this
image with your mobile phone
(QR code reader software is
necessary) or click on it.
R03.002_27/04/2016
TECHNICAL FILE
1. Spread a big amount of mortar on the surface to be tiled.
2. Then, place the prole and press it to make the mortar pass through the mechanized holes of the
xing wing. Be sure you also ll out the inside of the prole with mortar to reinforce it.
3. Put a tile on the xing wing and press to an optimal contact with the gripping material.
4, Repeat the operation placing tiles both sides of the prole until the installation is complete.
5. Finally, clean the remaining material, remove the protective lm if necessary and let dry.
* If you plan on polishing the oor, install the prole slightly below the tile.
As ooring
separator
Cleaning and maintenance
The cleaning must be done periodically with a soft cloth. If you use a neutral liquid cleaner, you must
rinse the prole with cold water and dry to remove excess moisture. If dirtiness persists, clean the
prole with a solution with clean water and detergent or neutral soap 5%, brushing with a cloth that
has no particles that could scracht the nish. Ensure the lacquered surface is totally cold (maximum
20ºC) before the cleaning.
Steel wool, abrasive cleaners, souring products as well as strong acids (hydrochloric and
perchloric),strong bases (caustic soda or ammonia) or carbonated solutions are not recommended.
Citric acid is neither recommended because disolves the protective layer of the surface of aluminium.
Waxes, petrolatum, lanolin or similar substances are not appropriate. Solvents containing haloalkanes
(hydrouoroether and chlorinated solvents) and curing accelerators containing chlorides should not be
used (use special accelerators free of chlorides)
Page 3 of 4
Novolistel® 4 Aluminium
1 2
3 4
5
1. Spread a big amount of thin-set mortar on the riser
2. Place the tile on the riser and press to an optimal adherence
3. Then, spread a big amount of thin-set mortar on the tread and align the prole on its vertex (Do
not let overhang, the leverage may remove the step and the tiles). Then press for material to pass
through the mechanized holes of the xing wing. Be also sure that you ll out the inside of the
prole with mortar to reinforce it.
4. Place the tile on the tread, align it to the prole and ensure a perfect adhesion
5. Clean the possible remaining material, remove the protective lm if necessary and let dry.
As stair nosing or
worktop nish
1 2
3
4 5
To see the video, capture this
image with your mobile phone
(QR code reader software is
necessary) or click on it.
TECHNICAL FILE
R03.002_27/04/2016
Emac Complementos S.L. (Spain) info@emac.es // Emac America L.L.C. (FL,USA) [email protected] // Emac Italia S.R.L. (Italy) [email protected]
www.emac.es
Les données fournies le sont à titre informatif et ont été obtenues par notre fournisseur ou par Emac®.
En aucun cas elles ne constituent une garantie juridique par rapport aux propriérés et/ou fonctionnalités de l’application de ce matériau.
You can nd out more information about the technical features of Emac®’s products by downloading
its Technical File in www.emac.es.
If you have any query, please contact our Technical Department in [email protected].
Technical information
Outdoors Indoors Wall tilingPaving Recyclable
Novolistel® 4 Aluminium
Page 4 of 4
-
1
-
2
-
3
-
4
dans d''autres langues
- English: Emac NL415512 User manual
Documents connexes
-
Emac NR10AR1382 Guide d'installation
-
-
-
-
-
-
-
-
-