LG LW1012CR Le manuel du propriétaire

Taper
Le manuel du propriétaire
AIR CONDITIONER
Please read this manual carefully before operating
your set and retain it for future reference.
P/NO:MFL67415901
www.LG.com
MODELMODÈLE:/:&5
FRANÇAIS
OWNER’S MANUAL
GUIDE D’UTILISATION
S'il vous plaît lisez attentivement ce manuel avant d'utiliser
votre appareil et le conserver pour référence future.
CLIMATISEUR DE PIECÈ
TEMPERATURE
MFL67415901
2 Room Air Conditioner
FOR YOUR RECORDS
Write the model and serial numbers here:
Model #
Serial #
You can find them on a label on the side of each unit.
Dealer's Name
Date Purchased
Staple your receipt to this page in the event you need it
to prove date of purchase or for warranty issues.
READ THIS MANUAL
Inside you will find many helpful hints on how to use and
maintain your air conditioner properly. Just a little preventive
care on your part can save you a great deal of time and
money over the life of your air conditioner.
You'll find many answers to common problems in the chart
of troubleshooting tips. If you review our chart of
Troubleshooting Tips first, you may not need to call for
service at all.
PRECAUTION
Contact the authorized service technician for repair
or maintenance of this unit.
• Contact the installer for installation of this unit.
The air conditioner is not intended for use by young
children or invalids without supervision.
Young children should be supervised to ensure that
they do not play with the air conditioner.
When the power cord is to be replaced, replacement
work shall be performed by authorized personnel only
using only genuine replacement parts.
Installation work must be performed in accordance
with the National Electric Code by qualified and
authorized personnel only.
Safety Precautions..........................3
Prior to Operation ...........................7
Introduction ....................................8
Electrical Safety .............................9
Installation ....................................11
Operating Instructions .................16
Maintenance and Service ............19
Window-Type Air Conditioner Owner’s Manual
TABLE OF CONTENTS
Owner’s Manual 3
ENGLISH
Safety Precautions
Safety Precautions
To prevent injury to the user or other people and property damage, the following instructions
must be followed.
Incorrect operation due to ignoring instruction will cause harm or damage. The seriousness
is classified by the following indications.
Meanings of symbols used in this manual are as shown below.
This symbol indicates the possibility of death or serious injury.
This symbol indicates the possibility of injury or damage to properties only.
Be sure not to do.
Be sure to follow the instruction.
Installation
Don’t use a power cord, a
plug or a loose socket which
is damaged.
O&D85BG9C59D=1I31EC51
fire or electrical shock.
Always plug into a grounded
outlet.
O&D85BG9C59D=1I31EC51
fire or electrical shock.
Do not modify or extend the
power cord length.
O DG9<<31EC55<53DB93C8?3;?B
fire due to heat generation.
Do not disassemble or
modify products.
O D=1I31EC5619<EB51>4
electric shock.
Be caution when unpacking
and installing.
O)81B@5475C=1I31EC5
injury.
Do not use the power cord near
flammable gas or combustibles
such as gasoline, benzene,
thinner, etc.
O D=1I31EC55H@<?C9?>?B
fire.
Gasolin
4 Room Air Conditioner
Safety Precautions
Operation
Do not place the power cord
near a heater.
O D=1I31EC569B51>45<53DB93
C8?3;
Do not allow water to run
into electric parts.
O DG9<<31EC5619<EB5?6=1389>5
?B5<53DB93C8?3;
Use a soft cloth to clean. Do
not use wax, thinner, or a
strong detergent.
O*851@@51B1>35?6D8519B
3?>49D9?>5B=1I45D5B9?B1D5
381>753?<?B?B45F5<?@
CEB61356<1GC
Wax
Thinner
Ventilate the room well when
using this appliance
together with a stove, etc.
O>?HI75>C8?BD175=1I
?33EB
Turn off the power and
breaker firstly when
cleansing the unit.
O)9>35D8561>B?D1D5C1D8978
C@5544EB9>7?@5B1D9?>9D=1I
31EC59>:EBI
Turn off the main power
switch when not using it for
a long time.
O'B5F5>D133945>D1<CD1BDE@1>4
D85@?CC929<9DI?69>:EBI
Unplug the unit if strange
sounds, odors, or smoke
come from it.
O&D85BG9C59D=1I31EC569B5
1>45<53DB93C8?3;133945>D
Do not open the suction
inlet grill of the product
during operation.
O&D85BG9C59D=1I5<53DB931<
C8?3;1>4619<EB5
If water enters the product, turn
off the the power switch of the
main body of appliance. Contact
service center after taking the
power-plug out from the socket.
Do not place heavy object
on the power cord and take
care so that the cord should
not be pressed.
O*85B59C41>75B?669B5?B
5<53DB93C8?3;
Do not share the outlet with
other appliances.
O DG9<<31EC55<53DB93C8?3;?B
69B54E5D?851D75>5B1D9?>
Take the power plug out if
necessary, holding the head
of the plug and do not touch
it with wet hands.
O&D85BG9C59D=1I31EC51
69B5?B5<53DB931<C8?3;
Owner’s Manual 5
ENGLISH
Safety Precautions
Installation
Do not operate or stop the
unit by inserting or pulling
out the power plug.
Do not damage or use an
unspecified power cord.
Do not operate with wet
hands or in damp
environment.
Hold the plug by the head
when taking it out.
When gas leaks, open the
window for ventilation
before operating the unit.
Never touch the metal parts
of the unit when removing
the filter.
Install the product so that the noise or hot
wind from the outdoor unit may not cause
any damage to the neighbors.
Keep level parallel in installing the product.
For inner cleaning, contact an Authorized Service Center or a dealer.
Do not use harsh detergent that causes corrosion or damage on the unit.
Harsh detergent may also cause failure of product, fire, or electronic shock.
6 Room Air Conditioner
Safety Precautions
Operation
Be cautious not to touch the
sharp edges when
installing.
x It may cause injury.
Avoid excessive cooling and
perform ventilation
sometimes.
x Otherwise, it may do harm
to your health.
Do not insert the hands or
bars through the air inlet or
outlet during operation.
x Otherwise, it may cause
personal injury.
Do not put a pet or house
plant where it will be
exposed to direct air flow.
x It may cause injury.
Do not block the inlet or
outlet of air flow.
x It may cause product failure.
Use a soft cloth to clean. Do
not use wax, thinner, or a
strong detergent.
x The appearance of the air
conditioner may deteriorate,
change color, or develop
surface flaws.
Do not step on the
indoor/outdoor unit and do
not put anything on it.
x It may cause an injury
through dropping of the unit
or falling down.
Always insert the filter
securely.
Clean it every two weeks.
x Operation without filters will
cause failure.
Do not drink water drained
from air conditioner.
x It contains containments and
will make you sick.
Owner’s Manual 7
ENGLISH
Prior to Operation
1. Contact an installation specialist for installation.
2. Plug in the power plug properly.
3. Use a dedicated circuit.
4. Do not use an extension cord.
5. Do not start/stop operation by plugging/unplugging the power cord.
6. If the cord/plug is damaged, replace it with only an authorized replacement
part.
1. Being exposed to direct airflow for an extended period of time could be
hazardous to your health. Do not expose occupants, pets, or plants to direct
airflow for extended periods of time.
2. Due to the possibility of oxygen deficiency, ventilate the room when used
together with stoves or other heating devices.
3. Do not use this air conditioner for non-specified special purposes (e.g.
preserving precision devices, food, pets, plants, and art objects). Such usage
could damage the items.
1. Do not touch the metal parts of the unit when removing the filter. Injuries can
occur when handling sharp metal edges.
2. Do not use water to clean inside the air conditioner. Exposure to water can
destroy the insulation, leading to possible electric shock.
3. When cleaning the unit, first make sure that the power and breaker are turned
off. The fan rotates at a very high speed during operation. There is a
possibility of injury if the unit’s power is accidentally triggered on while
cleaning inner parts of the unit.
For repair and maintenance, contact your authorized service dealer.
Prior to Operation
Preparing for Operation
Usage
Cleaning and Maintenance
Service
8 Room Air Conditioner
Introduction
Introduction
This symbol alerts you to the risk of electric shock.
This symbol alerts you to hazards that could cause harm to the
air conditioner.
This symbol indicates special notes.
NOTICE
°C
CABINET
AIR DISCHARGE
VERTICAL AIR DEFLECTOR
(HORIZONTAL LOUVER)
CONTROL BOARD
CONDENSER
COMPRESSOR
EVAPORATOR
POWER CORD
BASE PAN
BRACE
SIDE LOUVER
FRONT GRILLE
AIR FILTER
AIR INTAKE
(INLET GRILLE)
°C
Symbols Used in this Manual
Features
This appliance should be installed in accordance with the National Electric Code.
Owner’s Manual 9
ENGLISH
Electrical Safety
Electrical Safety
Electrical Data
115V~ 230V~
Power cord may include a current
interrupter device. A test and reset button is
provided on the plug case. The device
should be tested on a periodic basis by first
pressing the TEST button and then the
RESET button. If the TEST button does not
trip or if the RESET button will not stay
engaged, discontinue use of the air
conditioner and contact a qualified service
technician.
Use Wall Receptacle Power Supply
Standard 125V, 3-wire grounding
receptacle rated 15A, 125V AC
Standard 250V, 3-wire grounding
receptacle rated 15A, 250V AC
Use 15 AMP. time
delay fuse or 15 AMP.
circuit breaker.
Use 20 AMP. time
delay fuse or 20 AMP.
circuit breaker.
Standard 250V, 3-wire grounding
receptacle rated 20A, 250V AC
The shape may be different according to its model.
NOTICE
DO NOT USE AN EXTENSION CORD on 230, 208, and
230/208 Volt units.
All wiring should be made in accordance with local
electrical codes and regulations.
Aluminum house wiring may pose special problems.
Consult a qualified electrician.
NOTICE
Never push the test button during
operation
Otherwise this plug can damaged.
This device contains chemical, including lead,
known to the State of California to cause
cancer, and birth defects or other reproductive
harm.
Wash hands after handling.
Do not remove, modify or immerse this plug.
If this device trips, the cause it to be corrected
before further use.
The conductors inside this cord are
surrounded by shields, which monitor
leakage current.
These shields are not grounded.
Periodically examine the cord for any
damage. Do not use this product in the
event the shields become exposed.
Avoid shock hazard, this unit can not be
user serviced opening the tamper
resistant. Sealed portion of the unit
voids all warranties and performance
claims. This unit not intended for use as
an on-off switch.
Use of adapter plugs not pemitted in Canada.
Installation
Installation
Window Requirements
Installation Parts
8
7
9 10
3
12
11
16
17
1
6
13
15
4
14
2
5
NO. NAME OF PARTS QTY
1 Curtain 1
2 Curtain Frame 1
3 Upper Guide 1
4 Side Guide 2
5 Support Bracket 1
6 Bracket 1
7 Leveling Bolt & Nut 1
8 Bolt 2
9 Nut 2
10 Washer 2
11 Side Guide seal 1
12 Foam Seal Strip 1
13 Window Track Seal 1
14 Window Locking Bracket 1
15 Screw (Type A) 9
16 Screw (Type B) 3
17 Screw (Type C) 8
533mm min.
1029mm max.
394mm
min.
546mm min.
394mm min.
419mm max.
Horizontal sliding window Casement window
1. These instructions are for a horizontal sliding
or a casement window.
2. The electrical outlet must be within reach of
the power cord.
For installation in a casement window, the
window frame assembly and the side of the
building must be adequate to support the weight
of the air conditioner.
11 Room Air Conditioner
Installation
NOTICE
How to Install the Unit
1. To prevent vibration and noise, make sure the
unit is installed securely and fir mly
2. Install the unit where the sunlight does not
shine directly on the unit.
3. The outside of the cabinet must extend outward
for at least 356mm and there should be no
obstacles, such as a fence or wall, within 508mm
from the back of the cabinet because it will
prevent heat radiation of the condenser.
Restriction of outside air will greatly reduce the
cooling efficiency of the air conditioner.
All side louvers of the cabinet must remain exposed to the outside of the str ucture.
4. Install the unit at a slight incline so the bac k is slightly lower than the front(about 6.4mm).
This will force condensed water to flow to the outside.
5. Install the unit with the bottom about 762mm ~1524mm above the floor level.
762mm
1524mm
6.4mm
Horizontal Sliding Window Installation
1. Loosely attach the Support Bracket to the
bottom of Bracket using Bolts, Washer, and
Nuts. Attach the Leveling Bolt and Nut. (Fig. 1)
2. Remove protective backing from Window
Track Seal and apply seal to windo w track.
(Fig.2)
3. Measure and lightly mark a line 210mm
from window jamb. Center the Support
Bracket assembly on the window track and
fasten with 4 Type C screws.(Fig. 2)
1
/4
210mm
WindoWindow JambWindow Jamb
WindoWindow TrackWindow Track
WindoWindow Track
Seeal
Window Track
Seal
Bracket
Support Bracket
Nut
Washer
Leveling Bolt & Nut
Bolt
Type C screw
Type C screw
Fig. 1
Fig. 2
Owner’s Manual 12
ENGLISH
Installation
4. Put the Support Bracket against the outside
wall and tighten the Bolts on top of the
Bracket. Adjust the Leveling Bolt so that the
air conditioner will be installed with a v ery
slight tilt (about 6.4mm) downward toward the
outside for proper drainage.
Tighten the nut. (Fig. 3)
DO NOT drill a hole in the bottom of
the base pan. The air conditioner is
designed to operate with the bottom
of the base pan approximately half-full
of water.
5. Fasten Side Guides to the sides of the Air
Conditioner using 3 Type A screws per Guide.
Start with first screw at middle of Guide.
(Fig. 4)
6. Fasten Upper Guide on the top of the Air
Conditioner using
3 Type A screws. (Fig. 4)
7. Measure height of window opening from top
of Bracket assembly as shown Fig. 5.
Subtract 527mm. Mark this
measurement on Curtain and cut the Cur tain.
(Fig. 5)
8. Slide Curtain into Curtain Frame. Slide
Curtain Frame assembly into side Guides of
the Air Conditioner cabinet. Make sure
Curtain is firmly enclosed on all sides by the
Frame. (Fig. 6)
NOTICE
About
llaW edistuO
Fastening Side Guides
Upper Guide
Side Guide
o
C
Fig. 3
Fig. 4
Frame Curtain
Curtain
Fig. 5
Fig. 6
13 Room Air Conditioner
6.4mm
9. Cut side Guide seal into 2 equal lengths .
Remove protective backing and apply it to the
rear side of cabinet Side Guides, starting just
below Curtain Frame assembly. Pinch off
excess length so seal is even with the bottom
of side Guide. (Fig. 7)
10. Place Air Conditioner in window opening. It
should sit on Bracket assembly so that
Curtain Frame and cabinet Side Guides are
against top and side window jambs. Mate
front of Bracket with Base Guide attached to
the bottom of base pan.
11. Drill 3.2mm holes in window track through
the existing holes on Base Guide. Screw 4
Type C screws through the holes. (Fig. 8)
12. If this is a casement window installation,
proceed to Casement Window Installation. If
not, slide inner window sash firmly against
side of the cabinet.
13. Drill 3.2mm hole in window jamb to align
with the existing holes in the Curtain Frame.
Attach Curtain Frame to window frame with
2 Type B screws. (Fig. 8)
Apply weather seal
to side guides
just below edge of
Curtain Frame .
Type B screw
Type B screw
Base pan
Base pan
Bracket
Bracket
Windo
Windo
w Track
Base Guide
Base Guide
Type C screw
Window Track
o
C
Fig. 7
Fig. 8
Check all seals and plug any
remaining air gaps with a suitable
weatherproof caulk.
14. If this is a casement window installation,
proceed to Casement Window Installation.
If not, stuff the Foam Seal Strip between the
vertical sash and the window glass. (Fig. 9)
15. Attach the L Bracket with a Type B screw.
(Fig. 9)
NOTICE
Foam seal strip
Window
locking
bracket
o
C
Fig. 9
Owner’s Manual 14
HSILGNE
Installation
HSILGNE
ENGLISH
Installation
Installing the Power cord
A
Power cord
Screw (Type A)
Power cord
B
Screw (Type A)
°
C
°
C
You can choose between the two methods below according to your preference and window sill
shape.
• Fasten the stopper using Type A screw, and
pass the power cord through slit "A".
• Fasten the stopper using left screw hole, and
rotate properly to pass the power cord through
slit "B".
Using slit "A" Using slit "B"
Casement Window Installation
1. Installation procedure is the same as that descr ibed in steps 1 through 11 and step 13 of the
Horizontal Sliding Window installation.
2. If the window opening is wider than 400mm y ou will need to install a filler panel. Make this
panel from 19mm thick wood and run it the full length of the windo w.
Attach it securely to the window frame and paint it to protect it from the w eather.
3. Since styles and sizes of casement windows vary widely, it is advisable to have the air conditioner
installed by someone skilled in this type of installation.
15 Room Air Conditioner
Operating Instructions
Controls
Remote Control Operations
AUTO RESTART
When power is restored after an electrical power failure, the unit will begin to run at its last setting.
1. POWER
To turn the air conditioner ON, push this button.
To turn the air conditioner OFF, push the button
again.
This button takes priority over any other button.
When you first turn it on, the unit is in cool mode,
high fan speed, temperature setting at 22°C.
2. TEMPERATURE SETTING
• Use this button to automatically control the
temperature of the room.
The temperature can be set within a range of
16°C to 30°C by increments of 1°C.
3. MODE
- Every time you push this button, it will cycle
through the following modes: COOL, ENERGY
SAVER and FAN.
- ENERGY SAVER
The fan stops when the compressor stops
cooling. Approximately every 3 minutes the fan
will turn on and the unit will check the room air to
determine if cooling is needed.
4.
FAN SPEED
• Every time you push this button, it advances the
setting as follows: {High(F3) Low(F1)
Med(F2) High(F3)}
5. TIMER
- SHUT-OFF TIME
You will usually use shut-off time while you sleep.
With unit running, use Timer to set number of
hours until shut-off.
• For your sleeping comfort, once Time is set, the
Temperature setting will raise 1°C after 30 min,
and 1°C after another 30 min.
• Every time you push Timer button, it advances
the Timer setting as follows: 1 Hour 2 Hours
etc. 24 Hours maximum.
- START TIME
With unit not running, use timer to set number of
hours before unit starts.
• Every time you push Timer button, it advances
the Timer setting as follows: 1 Hour 2 Hours
etc. 24 Hours maximum.
6. REMOTE CONTROL SENSOR
Owner’s Manual 16
HSILGNE
Operating Instructions
HSILGNE
Temp
Fan Speed
Timer Mode
1
2
4
3
5
The remote control and control panel will look like those represented in the following pictures.
2
4
C
5
1
6
3
one
battery
the
battery is
battery
battery
y
CAUTION
If the liquid from the batteries gets onto your skin or clothes, wash it well with clean water.
Do not use the remo te if the battery have leaked.
• If you eat the .rotcod ees dna hteet ruoy hsurb ,yrettab eht morf diuqil
The chemicals in batteries could cause burns or other health hazards.
17 Room Air Conditioner
Operating Instructions
Additional Features
Drain Pipe
In humid weather, excess water may cause the BASE
PAN to overflow and be splashed on the side louver.
To drain the water, remove the DRAIN CAP and
secure the DRAIN PIPE to the rear hole of the BASE
PAN.
Ventilation
The ventilation lever must be in the CLOSE position in order to
maintain the best cooling conditions.
When fresh air is necessary in the room, set the ventilation
lever to the OPEN position.
When the damper is opened and room air is exchanged with
external air.
Air Direction
The direction of air can be controlled wherever you want to cool
by adjusting the horizontal louver and the vertical louver.
• HORIZONTAL AIR-DIRECTION CONTROL
The horizontal air direction is adjusted by
rotating the vertical louver right or left.
VERTICAL AIR-DIRECTION CONTROL
The vertical air direction is adjusted by rotating the horizontal
louver forward or backward.
VENTCLOSE
OPEN
Drain pipe
Drain cap
°
C
°C
Operating Instructions
Owner’s Manual 18
ENGLISH
Maintenance and Service
Maintenance and Service
TURN THE AIR CONDITIONER OFF AND REMOVE THE PLUG FROM THE POWER OUTLET.
Air Filter Cleaning
The air filter behind the front grille should be checked and cleaned at least once every 2 weeks or
more often if necessary.
To remove:
1. Open the inlet grille downward by pulling out the top of the inlet grille.
2. Remove the air filter from the front grille assembly by pulling the air filter up slightly.
3. Clean the filter with warm, soapy water below 40°C (104°F).
4. Rinse and gently shake the water from the filter and let it dry before replacing it.
CAUTION: DO NOT operate the air conditioner without a filter because dirt and lint
will clog it and reduce performance.
NOTE!
Before using the air conditioner secure the front grille with two
screws enclosed with the owner’s manual.
1. Open the inlet grille downward and remove the air filter.
2. Fasten the front grille with screws.
3. Reinstall the air filter.
4. Close the inlet grille.
Inlet Grille
°C
°C
19 Room Air Conditioner
Problem
ƵThe air conditioner is unplugged or
not plugged in completely.
ƵThe fuse is blown/circuit breaker is
triggered.
ƵPower failure.
ƵAir flow is restricted.
ƵTEMP Control set too higher
number.
ƵThe air filter is dirty.
ƵThe air conditioner was just
turned on.
ƵCold air is escaping.
ƵCooling coils are iced up.
ƵThe cooling coils are iced over.
The air
conditioner
does not
operate at all
Air
conditioner
does not cool
Ice appears
on the air
conditioner.
• Make sure the plug is completely plugged into
the outlet.
• Check the fuse/circuit breaker box and replace
the fuse or reset the breaker.
• In the event of a power failure, set the power
control to OFF. When the power is restored,
wait 3 minutes to restart the air conditioner to
prevent the compressor from overloading.
• Make sure there are no cur tains, blinds,
furniture or other obstacles in front of the air
conditioner.
• Set the TEMP control to a lower number.
• Clean the filter at least every 2 weeks. Refer
to the "Care and Maintenance" section (p .18)
of the manual.
• After the air conditioner is tur ned on, you need
to give the air conditioner some time to cool
the room.
• Check for open furnace floor resisters and
cold air returns.
• CLOSE the air conditioner vent.
• See Ice appears on the air conditioner
below.
• Ice may block the air flow and obstruct the air
conditioner from properly cooling the room.
Set the mode control at High Fan or High Cool
with the high temperature.
What To DoPossible Causes
Troubleshooting
Normal Operation
Maintenance and Service
You may hear a pinging noise caused by water being picked up and thrown against the
condenser on rainy days or when the humidity is high. This design feature helps remove
moisture and improve efficiency.
You may hear the thermostat click when the compressor cycles on and off.
Water will collect in the base pan during high humidity or on rainy days. The water may overflow
and drip from the outdoor side of the unit.
The fan may run even when the compressor does not.
Troubleshooting Tips
Save time and money! Review the chart below first and you may not need to call for service.
Owner’s Manual 20
ENGLISH
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43

LG LW1012CR Le manuel du propriétaire

Taper
Le manuel du propriétaire

dans d''autres langues