DeWalt Pressure Washer DXPW3025 Manuel utilisateur

DXPW3025

Pressure Washer

Laveuse à pression

Lavadora a presión

INSTRUCTION MANUAL

GUIDE D'UTILISATION

MANUAL DE INSTRUCCIONES

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE

GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES DE

USAR EL PRODUCTO.

If you have questions or comments, contact us.

Pour toute question ou tout commentaire, nous contacter.

Si tiene dudas o comentarios, contáctenos.

1-877-FNA-GAS1 (1-877-362-4271)•www.dewaltpw.com

2

English

A. Panel assembly

B. Nozzle holder

C. Professional Spray gun

D. Wheel

E. Quick-connect

spray wand

F. Frame

G. Engine dipstick/oil plug

H. Engine switch

I. Starter grip

J. Engine

K. Throttle control lever

L. Choke control

M. Fuel valve lever

N. Gas cap

O. Handle assembly

P. High-pressure hose

Q. High-pressure pump

DXPW3025 PRESSURE WASHER

Engine

Refer to the engine instruction manual for location and

operation of other engine controls.

Pump

For best results, pump oil designed specifically for

pressure washers is recommended, as these contain a

rust inhibitor and an anti-foaming agent. If this oil is not

available, an SAE 30W non-detergent oil may be used.

FIG. 1

J

C

E

A

B

Q

H

N

D

F

O

G

K

L

M

I

P

3

English

Deﬁnitions: Safety Guidelines

The definitions below describe the level of severity for each

signal word. Please read the manual and pay attention to these

symbols.

DANGER: Indicates an imminently hazardous situation which,

if not avoided, will result in death or serious injury.

WARNING: Indicates a potentially hazardous situation which,

if not avoided, could result in death or serious injury.

CAUTION: Indicates a potentially hazardous situation which,

if not avoided, may result in minor or moderate injury.

NOTICE: Indicates a practice not related to personal injury

which, if not avoided, may result in property damage.

IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS

CONTACT US AT: www.dewaltpw.com or 1-877-FNA-GAS1

(1-877-362-4271)

Speciﬁcations

MODEL WEIGHT HEIGHT WIDTH LENGTH PSI** GPM** ENGINE

DXPW3025 85 lbs

(38.5 kg)

22"

(55.9 cm)

21"

(53.3 cm)

34"

(86.4 cm)

3000

(20684 kPa)

2.5

(9.5 L/min)

HONDA GX160***

163 cc

** PSI and GPM ratings determined in accordance with the Pressure Washers Manufacturers Association (PWMA)

standard PW101.

*** HONDA™ is a registered trademarks of the HONDA MOTOR CO., LTD used under license from AMERICAN HONDA MOTOR CO. INC.

Important Safety Instructions

DANGER: Carbon Monoxide. Using an engine indoors can kill

you in minutes. Engine exhaust contains high levels of carbon

monoxide (CO), a poisonous gas you cannot see or smell. You

may be breathing CO even if you do not smell engine exhaust.

WARNING: This product and its exhaust contain chemicals

known to the State of California to cause cancer, and birth

defects and other reproductive harm.

• NEVER use an engine inside homes, garages, crawlspaces or

other partly enclosed areas. Deadly levels of carbon monoxide can

build up in these areas. Using a fan or opening windows and doors

does NOT supply enough fresh air.

• ONLY use outdoors and far away from open windows, doors and

vents. These openings can pull in engine exhaust.

• Even when the engine is used correctly, CO may leak into your

home. ALWAYS use a battery-powered or battery backup CO

alarm in your house. Read and follow all directions for CO

alarm before using. If you feel sick, dizzy or weak at anytime,

move to fresh air immediately. See a doctor. You could have

carbon monoxide poisoning.

4

English

WARNING: Do not operate this unit until you read this instruction

manual and the engine instruction manual for safety, operation and

maintenance instructions.

WARNING: When using this product basic precautions should

always be followed, including the following:

1. Read all instructions before using the product.

2. To reduce the risk of injury, close supervision is necessary when a

product is used near children.

3. Know how to stop the product and bleed pressures quickly. Be

thoroughly familiar with the controls.

4. Stay alert–watch what you are doing.

5. Do not operate the product when fatigued or under the influence of

alcohol or drugs.

6. Keep operating area clear of all persons.

7. Do not overreach or stand on unstable support. Keep good

footing and balance at all times.

8. Follow the maintenance instructions speciﬁed in the manual.

DANGER: RISK OF INJECTION OR SEVERE INJURY. KEEP

CLEAR OF NOZZLE. DO NOT DIRECT DISCHARGE STREAM

AT PERSONS. THIS PRODUCT IS TO BE USED ONLY BY

TRAINED OPERATORS.

WARNING: This product may not be equipped with a spark-

arresting muffler. If the product is not equipped and will be used

around flam ma ble ma teri als or on land covered with materials such

as agricultural crops, forest, brush, grass or other similar items,

then an ap proved spark arrester must be installed and is legally

required in the state of California. It is a violation of California statutes

section 130050 and/or sec tions 4442 and 4443 of the California

Public Re sourc es Code, unless the engine is equipped with a spark

arrester, as defined in section 4442, and maintained in ef fec tive

work ing order. Spark arresters are also required on some U.S. For est

Service land and may also be legally required under other statutes and

or di nanc es.

WARNING: This product and its exhaust contain chemicals

known to the State of California to cause cancer, and birth

defects or other reproductive harm. In addition, some cleaning

products and dust contain chemicals known to the State

of California to cause cancer, and birth defects or other

reproductive harm. Wash hands after handling.

SAVE THESE INSTRUCTIONS

DANGER: RISK OF EXPLOSION OR FIRE

WHAT CAN HAPPEN HOW TO PREVENT IT

• Spilled gas o line and it’s

vapors can be come ignited

from cigarette sparks,

electrical arcing, exhaust

gas es and hot engine

components such as

the muffler.

• Shut off en gine and allow

it to cool before adding fuel

to the tank.

• Use care in fill ing tank to

avoid spill ing fuel. Move

pressure wash er away

from fueling area before

start ing en gine.

• Heat will ex pand fuel in the

tank which could result in

spillage and pos si ble fire

explosion.

• Keep maximum fuel level

1/2" (12.7 mm) be low

bottom of filler neck

to allow for expansion.

5

English

• Operating the pressure

washer in an ex plo sive

en viron ment could

re sult in a fire.

• Operate and fuel equipment

in well-ven ti lat ed areas free

from ob struc tions. Equip

areas with fire extinguisher

suit able for gas o line fires.

• Materials placed against or

near the pressure washer

can in ter fere with its proper

ventilation fea tures caus ing

overheating and possible

ig ni tion of the materials.

• Never op er ate pressure

wash er in an area containing

dry brush or weeds.

• Muffler exhaust heat can

damage paint ed sur fac es,

melt any material sen si tive

to heat (such as siding,

plas tic, rub ber, vinyl or the

pressure hose, itself), and

dam age live plants.

• Always keep pressure

washer a min i mum of 4'

(1.2m) away from sur fac es

(such as houses, au to mo-

biles or live plants) that could

be damaged from muffler

exhaust heat.

• Improperly stored fuel could

lead to acciden tal ignition.

Fuel im prop er ly secured

could get into the hands of

children or oth er un qual i fied

persons.

• Store fuel in an OSHA

approved con tain er, in a

se cure location away from

work area.

• Use of acids, toxic or

cor ro sive chemicals,

poisons, in sec ti cides, or any

kind of flam ma ble solvent

with this product could

re sult in se ri ous injury or

death.

• Do not spray flammable

liquids.

DANGER: RISK TO BREATHING (ASPHYXIATION)

WHAT CAN HAPPEN HOW TO PREVENT IT

• Breathing ex haust fumes

will cause se ri ous injury

or death! En gine exhaust

con tains carbon mon ox ide,

an odorless and deadly gas.

• Operate pressure washer in

a well-ventilated area. Avoid

en closed areas such as

ga rag es, base ments, etc.

• Never op er ate unit in or near

a lo ca tion occupied by

humans or animals.

• Some clean ing fluids

con tain sub stanc es which

could cause injury to skin,

eyes or lungs.

• Use only clean ing fluids

spe cif i cal ly rec om mend ed

for high-pressure washers.

Fol low manufacturers

recommendations. Do not

use chlorine bleach or any

other corrosive compound.

6

English

• Do not allow hose to contact

muf fler.

• Never attach or remove

wand or hose fittings while

sys tem is pres sur ized.

• When using replacement

lances or guns with this

pressure washer, DO NOT

use a lance and/or lance/

gun combination that

is shorter in length than

what was provided with

this pressure washer as

measured from the nozzle

end of the lance to the gun

trigger.

• Injuries can result if system

pressure is not reduced

before attempting

maintenance or

disassembly.

• To relieve sys tem pres sure,

shut off engine, turn off

water sup ply and pull gun

trigger until water stops

flowing.

• Use only accessories rated

equal to or higher than

the rating of the pressure

washer.

DANGER: RISK OF FLUID INJECTION AND LACERATION

WHAT CAN HAPPEN HOW TO PREVENT IT

• Your pressure washer

operates at fluid pressures

and velocities high enough

to penetrate human and

animal flesh, which could

result in amputation or

other serious injury. Leaks

caused by loose fittings or

worn or damaged hoses

can result in injection

injuries. DO NOT TREAT

FLUID INJECTION AS

A SIMPLE CUT! See a

physician immediately!

• Inspect the high-pressure

hose regularly. Replace

the hose immediately if it is

damaged, worn, has melted

from contacting the engine,

or shows any signs of

cracks, bubbles, pinholes, or

other leakage. Never grasp a

high-pressure hose that

is leaking or damaged.

• Never touch, grasp or

attempt to cover a pinhole

or similar water leak on the

high-pressure hose. The

stream of water IS under

high pressure and WILL

penetrate skin.

• Never place hands in front

of noz zle.

• Direct spray away from self

and others.

• Make sure hose and fit tings

are tight ened and in good

condition. Never hold onto

the hose or fittings during

op er a tion.

7

English

DANGER: RISK OF INJURY FROM SPRAY

WHAT CAN HAPPEN HOW TO PREVENT IT

• High-velocity fluid spray

can cause objects to break,

propelling particles at high

speed.

• Always wear ANSI-approved

Z87.1 safety glasses. Wear

protective clothing to protect

against accidental spraying.

• Never point wand at or

spray people or animals.

• Light or unsecured objects

can become hazardous

projectiles.

• Always secure trigger lock

when wand is not in service

to prevent accidental

operation.

• Never permanently secure

trigger in pull-back (open)

position.

DANGER: RISK OF UNSAFE OPERATION

WHAT CAN HAPPEN HOW TO PREVENT IT

• Unsafe op er a tion of your

pressure wash er could lead

to se ri ous in ju ry or death to

you or others.

• Do not use chlorine

bleach or any other

corrosive compound.

• Be come fa mil iar with the

op er a tion and con trols of

the pressure washer.

• Keep operating area clear

of all persons, pets and

obstacles.

• Do not operate the product

when fatigued or under the

influence of alcohol or drugs.

Stay alert at all times.

• Never defeat the safety

fea tures of this prod uct.

• Do not op er ate machine

with missing, broken or

un au tho rized parts.

• Never leave wand

unattended while unit

is running.

8

English

• If proper starting procedure

is not followed, engine can

kickback causing serious

hand and arm injury.

• If engine does not start after

two pulls, squeeze trigger

of gun to relieve pump

pressure. Pull starter cord

slowly until resistance is felt.

Then pull cord rapidly to

avoid kickback and prevent

hand or arm injury.

• The spray gun/wand is

a powerful clean ing tool

that could look like a toy

to a child.

• Keep chil dren away from the

pressure washer at all times.

• Reactive force of spray

will cause gun/wand to

kickback, and could cause

the op er a tor to slip or fall

or misdirect the spray.

Im prop er control of gun/

wand can re sult in

in ju ries to self and

others.

• Do not over reach or stand

on an unstable support.

• Do not use pressure washer

while standing on a ladder.

• Grip gun/wand firmly with

both hands. Expect the

gun to kickback when

triggered.

DANGER: RISK OF INJURY OR PROP ER TY DAMAGE

WHEN TRANSPORTING OR STORING

WHAT CAN HAPPEN HOW TO PREVENT IT

• Fuel or oil can leak or spill

and could result in fire or

breathing hazard. Se ri ous

in ju ry or death can re sult.

Fuel or oil leaks will dam age

carpet, paint or oth er

surfaces in ve hi cles

or trailers.

• Oil could fill the cylinder and

damage the engine if the unit

is not stored or transported

in an upright position.

• If pressure washer is

equipped with a fuel shut-

off valve, turn the valve to

the OFF position before

transporting to avoid fuel

leaks. If pres sure wash er is

not equipped with a fuel shut-

off valve, drain the fuel from

tank before trans port ing. Only

trans port fuel in an OSHA-

approved container.

Al ways place pressure

washer on a protective mat

when transporting to protect

against dam age to vehicle

from leaks.

Always transport and store

unit in an upright position.

Re move pres sure washer

from vehicle immediately

upon arrival at your

destination.

9

English

WARNING: RISK OF BURSTING

WHAT CAN HAPPEN HOW TO PREVENT IT

• Over inflation of tires could

result in serious injury and

property damage.

• Use a tire pressure gauge

to check the tires pressure

before each use and while

inflating tires; see the tire

sidewall for the correct tire

pressure.

NOTE: Air tanks,

compressors and similar

equipment used to inflate

tires can fill small tires similar

to these very rapidly. Adjust

pressure regulator on air

supply to no more than the

rating of the tire pressure.

Add air in small increments

and frequently use the

tire gauge to prevent over

inflation.

• High-velocity fluid spray

directed at pneumatic tire

sidewalls (such as found

on automobiles, trailers and

the like) could damage the

sidewall resulting in serious

injury.

• On pressure washers rated

above 1600 psi (11032kPa)

use the widest fan spray

(40º nozzle) and keep the

spray a minimum of 8"

(20 cm) from the pneumatic

tire sidewall. Do not aim

spray directly at the joint

between the tire and rim.

WARNING: RISK OF HOT SURFACES

WHAT CAN HAPPEN HOW TO PREVENT IT

• Con tact with hot sur fac es,

such as engines exhaust

com po nents, could result in

se ri ous burn.

• During op er a tion, touch

only the control surfaces

of the pres sure washer.

Keep children away from

the pres sure washer at all

times. They may not be able

to recognize the haz ards of

this product.

10

English

WARNING: RISK OF CHEMICAL BURN

WHAT CAN HAPPEN HOW TO PREVENT IT

• Use of acids, toxic or

corrosive chemicals,

poisons, in sec ti cides, or any

kind of flam ma ble solvent

with this product could re sult

in se ri ous injury or death.

• Do not spray ac ids, gasoline,

ker o sene, or any other

flammable materials with this

product. Use only household

de ter gents, cleaners and

degreasers recommended

for use with pres sure

washers.

• Wear pro tec tive clothing

to protect eyes and skin

from con tact with sprayed

materials.

WARNING: RISK OF

ELEC TRI CAL SHOCK

WHAT CAN HAPPEN HOW TO PREVENT IT

• Spray di rect ed at elec tri-

cal outlets or switch es, or

ob jects con nect ed to an

elec tri cal circuit, could re sult

in a fatal electrical shock.

• Unplug any elec tri cal ly

op er at ed product before

attempting to clean it. Direct

spray away from electric

out lets and switches.

WARNING: RISK OF

INJURY FROM LIFTING

WHAT CAN HAPPEN HOW TO PREVENT IT

• Serious injury can result

from attempting to lift too

heavy an object.

• The pressure washer is too

heavy to be lifted by one

person. Obtain assistance

from others before lifting.

SAVE THESE INSTRUCTIONS

FOR FUTURE USE

11

English

NOTE: The high-pressure pump was filled with oil at the factory.

Always check oil level before using (refer to Maintenance for more

information).

WARNING: Risk of bursting.

Use a tire pressure gauge to check the

tires pressure before each use and while inflating tires; see the tire sidewall

for the correct tire pressure.

NOTE: Air tanks, compressors and similar equipment used to inflate

tires can fill small tires similar to these very rapidly. Adjust pressure

regulator on air supply to no more than the rating of the tire pressure.

Add air in small increments and frequently use the tire gauge to

prevent over inflation.

OPERATION

Pressure Adjustments

The pressure setting is preset at the factory to achieve op ti mum pres-

sure and cleaning. To lower the pres sure, follow these instructions.

1. Back away from the sur face to be cleaned. The further away you

are, the less the pressure will be on the surface to be cleaned.

2. Change to the 40˚ nozzle (white). This nozzle delivers a less

powerful stream of water and a wider spray pattern. Refer to

Spray Wand Nozzles.

NOTICE: DO NOT attempt to increase pump pressure. A higher

pressure setting than the factory set pressure may damage pump.

3. Reduce the speed of the gasoline engine (RPM). Slow the engine

down and the water pressure will go down with it.

Spray Wand Nozzles (Fig. 1)

The nozzles for the spray wand are stored in the nozzle holder (B) on the

panel assembly (A). Colors on the panel identify nozzle location and spray

pattern. Refer to the following chart to choose the correct nozzle for

the job to be performed.

INSTALLATION

Pressure Washer Assembly (Fig. 1)

1. Place handle (O) onto frame (F) and

R

F

O

secure with saddle bolts and knobs (R).

CAUTION: Risk of personal injury. Avoid

placing hands between handle and frame

when assembling to prevent pinching.

2. Attach high-pressure hose (P) to spray

gun. Make sure it is secure.

3. Connect wand (E) to spray gun. Make sure

connection is secure.

E

P

4. Place the nozzle holder (B) onto the panel assembly (A) and push

each nozzle holder into place.

5. Remove the five

B

A

colored quick-

connect nozzles from

the plastic bag and

insert them into

correct grommet on

the nozzle holder. Nozzles are color coded to match colored nozzles

on panel assembly.

12

English

Nozzle Color Spray Pattern Uses Surfaces*

Red

0˚

powerful

pinpoint for very

intense cleaning

metal or

concrete;

DO NOT use on

wood

Yellow

15˚

intense cleaning

of small areas

metal, concrete

or wood

Green

25

˚

intense cleaning

of larger areas

metal, concrete

or wood

White

40

˚

covers wide

areas of

cleaning

metal, concrete,

wood or vinyl

Black

low pressure

applies cleaning

solutions

metal, concrete,

wood or vinyl

* NOTICE: The high-pressure spray from your pressure washer

is capable of causing damage to surfaces such as wood, glass,

automobile paint, auto striping and trim, delicate objects such

as flowers and shrubs. Before spraying, check the item to

be cleaned to assure yourself that it is strong enough to resist

damage from the force of spray.

CHANGING NOZZLES ON SPRAY WAND

DANGER: Risk of fluid injection. Do not direct discharge stream

toward persons, unprotected skin, eyes or any pets or animals.

Serious injury will occur.

WARNING: Flying objects could cause risk of serious injury. DO

NOT attempt to change nozzles while pressure washer is running. Turn

engine off before changing nozzles.

1. Pull quick-connect coupler back and insert

nozzle.

2. Release quick-connect coupler and twist

nozzle to make sure it is secure in coupler.

WARNING: Flying object could cause risk

of serious injury. Ensure nozzle is completely

inserted in quick-connect socket and quick-

connect snap ring is fully engaged (forward)

before squeezing gun trigger.

Chemicals and Cleaning Solvents

Applying chemicals or cleaning solvents is a low-pressure operation.

NOTE: Use only soaps and chemicals designed for pressure washer

use. Do not use bleach.

TO APPLY CHEMICALS AND SOLVENTS

1. Press chemical hose (S) onto barbed fitting

S

located near high pressure hose connection

of pump as shown.

2. Place the other end of chemical hose with

filter on it into the container holding chemical/

cleaning solution.

NOTE: For every 10 gallons (38 liters) of water

pumped 1 gallon (3.8 liters) of chemical/

cleaning solution will be used.

13

English

3. Install low-pressure (black) nozzle into quick connect fitting of spray

wand, refer to Spray Wand Nozzles.

NOTE: Chemicals and soaps

will not siphon if the black soap nozzle is not installed on the spray

wand.

4. After use of chemicals, place chemical hose into container of clean

water and draw clean water through chemical injection system to

rinse system thoroughly. If chemicals remain in the pump it could

be damaged. Pumps damaged due to chemicals will not be

covered under warranty.

Starting

WARNING: To reduce the risk of injury, read the pressure washer

instruction manual and the engine instruction manual before starting

pressure washer.

DANGER: Risk of fluid injection and laceration. When using the

high-pressure setting, DO NOT allow the high-pressure spray to come

in contact with unprotected skin, eyes, or with any pets or animals.

Serious injury will occur.

• Your washer operates at fluid pressures and velocities high

enough to penetrate human and animal flesh, which could result

in amputation or other serious injury. Leaks caused by loose fit-

tings or worn or damaged hoses can result in injection injuries.

DO NOT TREAT FLUID INJECTION AS A SIMPLE CUT! See a

physician immediately!

WARNING: Risk of fire, asphyxiation and burning. Never fill fuel tank

when engine is running or hot. Do not smoke when filling fuel tank.

• NEVER fill fuel tank completely. Fill tank to 1/2" (12.7 mm) below

bottom of filler neck to provide space for fuel expansion. Wipe any

fuel spillage from engine and equipment before starting engine.

• NEVER run engine in doors or in en closed, poorly ven ti lat ed areas.

En gine exhaust con tains carbon mon ox ide, an odorless

and

deadlygas.

• DO NOT let hoses come in contact with very hot engine

muffler during or immediately after use of your pressure

washer. Damage to hoses from contact with hot engine

surfaces will NOT be covered by warranty.

NOTICE: NEVER pull water supply hose to move pres sure washer. This

could damage hose and/or pump inlet.

• DO NOT use hot water, use cold water only.

• NEVER turn water supply off while pressure washer engine is

running or damage to pump will result.

• DO NOT stop spraying water for more than

T

two minutes at a time. Pump operates in

bypass mode when spray gun trigger is not

pressed. When the temperature inside the pump

rises too high the thermal relief valve (T) will open

and release a gush of water in an effort to lower

the temperature inside the pump. The thermal

relief valve will then close. If pump is left in bypass mode for

more than two minutes internal components of the pump can

be damaged.

START-UP PROCEDURE

1. In a well-ventilated outdoor area, add fresh, high-quality, unleaded

gasoline with a pump octane rating of 86 or higher. Do not overfill.

Wipe up spilled fuel before starting the engine. Refer to engine

instruction manual for correct procedure.

2. Check engine oil level. Refer to the engine instruction manual for

correct procedure.

3. Connect the water hose to the water source. Turn the water source

on to remove all air from the hose. When a steady stream of water is

present, turn the water source off.

14

English

4. Verify the filter screen (U) is in water inlet of pump.

U

The cone side faces out.

5. Connect the cold water source (V) to pump inlet.

NOTE: Water source must provide a minimum of 5

gallons per minute at 20 psi (138 kPa).

WARNING: To reduce the possibility of

contamination always protect against backflow when

connected to a potable water system.

6. Connect high-pressure hose (P) to pump outlet.

V

P

7. If applying a chemical or cleaning solution,

refer to Chemicals and Cleaning Solvents.

8. Turn the water source on.

NOTICE: Risk of property damage. Failure to do

so could cause damage to the pump.

9. Remove all air from the pump and high pressure

hose by depressing trigger until a steady stream

of water is present.

10. Turn the engine ON/OFF switch (H) to the ON position.

11. Place the fuel valve lever (M) in the ON position.

12.

If the engine is cold, move the choke (L) to the CLOSED position

as shown.

M

H

L

13. WARNING: Risk of unsafe operation. Pull starter grip slowly

until resistance is felt. Then pull starter grip (I) rapidly to avoid

kickback and prevent hand or arm injury.

NOTE: Do not allow the starter grip to snap back. Return it gently by

hand.

WARNING: Risk of unsafe operation. If engine does not start after

two pulls, squeeze trigger of gun to relieve pump pressure. Pull starter

cord slowly until resistance is felt. Then pull cord rapidly to avoid

kickback and prevent hand or arm injury.

NOTE: If the oil level in the engine is low, the engine will not start. If

the engine does not start, check the oil level and add oil as needed.

14. As the engine warms up, move the choke to

the OPEN position.

15. Depress trigger on gun to start water flow.

WARNING: Risk of unsafe operation. Stand

on a stable surface and grip gun/wand firmly with

both hands. Expect the gun to kickback when

triggered.

16. Release trigger to stop water flow.

DANGER: Risk of injury from spray. Engage the

X

trigger lock (X) when gun is not in use to prevent

accidental spraying.

17. Adjust spray for the task being performed by

changing quick connect nozzle. Refer to Spray

Wand Nozzles.

Shutting Down

1. If chemicals were applied, place the chemical hose into a container

of clean water and draw clean water through chemical injection

system to rinse system thoroughly.

NOTICE: Risk of property damage Failure to do so could cause

damage to the pump.

2. Place the engine ON/OFF switch (H) to the OFF Position.

15

English

3. Place the fuel valve lever (M) in the OFF

position.

NOTICE: Risk of property damage. NEVER turn

water supply off while pressure washer engine is

running or damage to pump will result.

4. Turn water source off.

5. Pull trigger on spray gun to relieve any water

pressure in hose or spray gun.

6. Refer to Storage for proper storage procedures.

MAINTENANCE

WARNING: Risk of burning. When performing maintenance, you

may be exposed to hot surfaces, water pressure or moving parts that

can cause serious injury or death.

WARNING: Risk of fire. Always disconnect, spark plug wire, let

the engine cool and release all water pressure before performing any

maintenance or repair. The engine contains flammable fuel. Do not

smoke or work near open flames while performing maintenance.

To ensure efficient operation and longer life of your pressure washer,

a routine maintenance schedule should be prepared and followed.

If the pressure washer is used in unusual conditions, such as high

temperatures or dusty conditions, more fre quent maintenance checks

will be required.

Engine

Consult the engine instruction manual for the man u fac tur er's

recommendations for any and all maintenance.

NOTE: The pressure washer frame is equipped with an oil drain hole

to help make changing the engine oil easier.

Pump

NOTE: The pump was filled with oil at the factory. Change pump oil

after the first 50 hours of operation and every 300 hours thereafter, or

every 3 months. If using a 30W non-detergent oil, change oil every

150 hours thereafter.

TO CHECK OIL

The oil level should come to the dot in

BB

CC

AA

the middle of the sight glass (AA).

HOW TO CHANGE PUMP OIL

1. Loosen pump oil fill plug (BB).

2. Place a container under the oil

drain plug (CC).

3. Remove pump oil drain plug.

4. After oil is drained, replace oil

drain plug. Tighten securely.

5. Remove pump oil plug and fill with pump oil. An oil designed

specifically for pressure washers is recommended as these contain

a rust inhibitor and an anit-foaming agent. If this oil is not available,

an SAE 30W non-detergent oil may be used.

6. Replace pump oil plug and tighten securely.

Nozzle Cleaning

If the nozzle becomes clogged with foreign materials, such as dirt,

excessive pressure may develop. If the nozzle becomes partially

clogged or restricted, the pump pressure will pulsate. Clean the

nozzle immediately using the nozzle kit supplied and the following

instructions:

1. Shut off the pressure washer and turn off the water supply.

2. Pull trigger on gun handle to relieve any water pressure.

16

English

3. Disconnect the spray wand from the gun.

4. Remove the high-pressure nozzle from the

Y

spray wand. Remove any obstructions with

the nozzle cleaning tool (Y) provided and

back flush with clean water.

5. Direct water supply into spray wand to

back flush loosened particles for 30

seconds.

6. Reassemble the nozzle to the wand.

7. Reconnect spray wand to gun then turn on water supply.

8. Start pressure washer and place spray wand into high pressure

setting to test.

To Clean the Water Inlet Filter

This filter screen (U) should be checked periodically and cleaned if

necessary.

1. Remove the filter screen (U) by grasping the

U

end and removing it from water inlet of pump.

2. Clean filter by flushing it with water on both

sides.

3. Reinsert filter into water inlet of pump. Cone

side faces out.

NOTE: Do not operate pressure washer without

ﬁlter properly installed.

STORAGE

Engine

Consult the engine instruction manual for the man u fac tur er's

recommendations for storage.

Pump

The manufacturer recommends using a pump protector/

winterizer when storing the unit for more than 30 days and/or

when freezing temperatures are expected. If a pump protector/

winterizer is not available, RV antifreeze can be used as outlined in the

following steps.

NOTE: Using a pump protector/ winterizer or RV antifreeze helps

to provide proper lubrication to the internal seals of the pump

regardless of temperature or environment.

1. Obtain a funnel, 6 oz. (170 mL)

of RV antifreeze and 16–36" (40–

91cm) of garden hose with a male

hose connector attached to one

end.

NOTICE: Risk of property damage.

Use only RV antifreeze. Any other an ti-

freeze is corrosive and can damage

pump.

2. Disconnect spark plug wire.

3. Connect length of garden hose

to water inlet of pump.

4. Add RV antifreeze to hose as shown.

5. Pull engine starter rope slowly several times until an ti freeze

comes out of high-pressure hose con nec tion of pump.

6. Remove garden hose from water inlet of pump.

7. Reconnect spark plug wire.

17

English

Pressure Washer

1. Drain all water from high-pressure hose, coil it and store it in

cradle of the pressure washer handle.

2. With nozzle pointed down and the spray gun and wand in a

vertical position, squeeze trigger to drain all water from spray gun

and wand. Store in gun holder.

3. Store chemical hose so it is protected from dam age.

CAUTION: Risk of personal injury. Avoid placing hands between

handle and frame when assembling to prevent pinching.

NOTICE: Risk of property damage. Always store and transport unit

in an upright position.

ACCESSORIES

Recommended accessories for use with your tool are available for

purchase from your local dealer or authorized service center. If you

need assistance in locating any accessory for your tool, please contact

the FNA Group at www.dewaltpw.com, 1825 Greenleaf Avenue, Elk

Grove Village, Il 60007, or call (877) FNA-GAS1.

DANGER: Risk of fluid injection. When using replacement lances

or guns with this pressure washer, DO NOT use a lance and/or lance/

gun combination that is shorter in length than what was provided with

this pressure washer as measured from the nozzle end of the lance to

the gun trigger.

WARNING: The use of any other accessory not recommended

for use with this tool could be hazardous. Use only accessories rated

equal to or higher than the rating of the pressure washer.

SERVICE INFORMATION

Please have the following information available for all service calls:

Model Number ____________ Serial Number ___________

Date and Place of Purchase ___________________________________

Repairs

To assure product SAFETY and RELIABILITY, repairs, maintenance

and adjustment should be performed by a FNA factory service center,

a FNA authorized service center or other qualified service personnel.

Always use identical replacement parts.

18

English

Limited Warranty

The manufacturer of this product agrees to repair or replace designated

parts that prove defective within the warranty period listed below at the

manufacturer’s sole discretion. Specific limitations/extensions and

exclusions apply.

This warranty covers defects in material and workmanship and not

parts failure due to normal wear, depreciation, abuse, accidental

damage, negligence, improper use, maintenance, or storage. To make

a claim under the terms of the warranty, all parts said to be defective

must be retained and available for return upon request to a designated

Warranty Service Center for warranty inspection. The judgments and

decisions of the manufacturer concerning the validity of warranty

claims are final.

These warranties pass through to the end user and are non-

transferable. As a factory authorized and trained Warranty Service

Center, the factory will honor the terms of all component warranties

and satisfy claims of the appropriate warranty provisions.

Normal wear items include, but are not limited to, valves and seals,

which are not covered by this warranty.

This warranty replaces all other warranties, express or implied,

including without limitation any warranties of merchantability or fitness

for a particular purpose and all such warranties are hereby disclaimed

and excluded by the manufacturer. The manufacturer’s warranty

obligation is limited to repair and replacement of defective products as

provided herein and the manufacturer shall not be liable for any further

loss, damages, or expenses – including damages from shipping,

accident, abuse, acts of God, misuse, or neglect. Neither is damage

from repairs using parts not purchased from the manufacturer or

alterations performed by non-factory authorized personnel. Failure to

install and operate equipment according to the guidelines put forth in

the instruction manual shall void warranty.

This warranty does not cover the following: machines used for

rental purposes, damage resulting from shipping (claims must be

filed with freighter), accident, abuse, act of God, misuse, or neglect.

Neither is damage from repairs or alterations performed by non-

factory authorized personnel or failure to install and operate equipment

according to the guidelines put forth in the instruction manual.

The manufacturer will not be liable to any persons for consequential

damage, for personal injury, or for commercial loss.

ENGINE

Covered by engine manufacturer warranty. See engine manual.

HIGH PRESSURE PUMP (DEFECTS IN MATERIAL AND

WORKMANSHIP)

Two (2) years from date of purchase.

WARRANTY DOES NOT APPLY TO FAILURES DUE TO:

• Freight damage

• Freeze damage

• Damage caused by parts or accessories not obtained from an

authorized dealer or not approved by the manufacturer.

• Normal wear of moving parts or components affected by moving

parts.

FRAME (DEFECTS IN MATERIAL AND WORKMANSHIP)

One (1) year from date of purchase.

ACCESSORIES (DEFECTS IN MATERIAL AND

WORKMANSHIP)

Includes nozzles, hoses, spray guns, wands

Ninety (90) days from date of purchase.

19

English

Glossary

Bypass mode: Allows water to re-circulate within pump when the gun trigger is not pulled.

Chemical hose: Feeds cleaning agents into the pump to mix with the water. Refer to Chemicals and Cleaning Solvents.

Chemical injection system: Mixes cleaners or cleaning solvents with water to improve cleaning effectiveness.

Choke control: Opens and closes carburetor choke valve.

CU: Cleaning Units. GPM multiplied by psi. (GPM x PSI = CU)

Fuel valve lever: Opens/closes connection between fuel tank and carburetor.

GPM: Gallons Per Minute. The unit of measure for the flow rate of water.

PSI: Pounds per Square Inch. The unit of measure for water pressure. Also used for air pressure, hydraulic pressure, etc.

kPa (kilopascal): Metric pressure measurement. 1 kilopascal equal 1000 pascals.

Quick-connect spray wand: Allows the user to quickly change out high-pressure nozzles. Refer to Spray Wand Nozzles.

Thermal relief valve: When the temperature inside the pump rises too high the valve will open and release a gush of water in an effort to lower

the temperature inside the pump. The valve will then close.

Water supply: All pressure washers must have a source of water. The minimum requirements for a water supply are 20 psi (138kPa) and

5gallons per minute.

20

English

Troubleshooting Guide

This section provides a list of the more frequently encountered malfunctions, their causes and corrective actions. The

operator or maintenance personnel can perform some corrective actions, and others may require the assistance of a qualified FNA technician

or your dealer.

Problem Code

Engine will not start ........................................................................................................1, 2, 3, 4, 5, 6, 7, 8, 36

(refer to the engine's instruction manual for further engine troubleshooting)

No or low pressure (initial use) ........................................................................................9, 10, 11, 12, 13, 14, 15, 16

Will not draw chemicals ..................................................................................................16, 17, 18, 19, 20, 21

No or low pressure (after period of normal use) ..............................................................22, 23, 24

Water leaking at gun/spray wand connection .................................................................25, 26

Water leaking at pump ....................................................................................................25, 26, 27, 28

Oil leaking at pump .........................................................................................................29, 30, 31, 32, 33, 34, 35

Pump Pulsates ................................................................................................................12

Troubleshooting Codes

CODE POSSIBLE CAUSE POSSIBLE SOLUTION

1 No fuel. Add fuel.

2 Low oil. Add required amount of oil.

3 Pressure builds up after two pulls on the recoil starter or after

initial use.

Squeeze gun trigger to relieve pres sure.

4 Choke lever in the NO CHOKE position. Move choke to the CHOKE po si tion.

5 Spark plug wire not attached. Attach spark plug wire.

6 Engine ON/OFF switch in OFF po si tion. Place engine ON/OFF switch in ON position.

7 Choke lever in the CHOKE position on a hot engine or an engine

that has been exposed to thermal heat for a long period of time.

Move choke to the NO CHOKE po si tion.

8 Fuel valve CLOSED. Move the fuel valve lever to the OPEN position.

9 Spray wand not in high pressure. See Spray Wand Nozzles under Operation.

La page charge ...

DeWalt Pressure Washer DXPW3025 Manuel utilisateur

Ce manuel convient également à

DeWalt Pressure Washer DXPW3025 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents