Summit SCR450L MED Series Manuel utilisateur

Marque: Summit

Modèle: SCR450L MED Series

Catégorie: Frigos

Taper: Manuel utilisateur

PLUS Series

REFRIGERATORS AND FREEZERS FOR GENERAL PURPOSE STORAGE

If you need service or call with a question, please have

this information ready. We advise you to keep this Use &

Care Guide in your possession.

Model: ___________ Serial number: _________________

Options added:

Date of purchase: Dealer:

MED/MEDDT Series

REFRIGERATORS AND FREEZERS FOR MEDICAL STORAGE

FELIX STORCH, INC.

ISO 9001:2008 Registered

770 Garrison Avenue

Bronx, New York 10474

medicalrefrigerators.com

USE & CARE GUIDE

NOTE: This manual is also

available in French.

Look on our website.

Model Numbers

PLUS Models

• FF6 / FF7 / FF28LWH / FF31L7 / FF511L / FF521BL / FFAR2L / FFAR21L /

FFAR24L / FFAR25L7 / FF590SSHH PLUS Series

All-refrigerators with automatic defrost or frost-free operation

• VT65ML PLUS Series

Low temperature freezers

• FFAR10 PLUS Series

Full-size storage all-refrigerators

• FS20L / FS21L / FS22L / FS24L PLUS Series

Compact all-freezers (-20°C)

• CM411L / CM421BL / CP35LL / CT66 / S19LWH PLUS Series

Compact refrigerator-freezers

• FCL44 / FS30L / FS60ML / FS407L / FS408BL PLUS Series

Compact and mid-size storage all-freezers

• SCR450L / SCR500BL / SCR600L / SCR610BL / SCR1156 PLUS Series

Glass door all-refrigerators

MED/MEDDT* Models

• FF6 / FF7 / FF28LWH / FF31L7 /FF511L / FF521BL / FF590SSHH / FFAR2L /

FFAR21L / FFAR24L / FFAR25L7 MED Series

All-refrigerators with automatic defrost or frost-free operation

• FFAR10 MED Series

Full-size storage all-refrigerators

• SCR450L / SCR500BL / SCR600L / SCR610BL / SCR1156 / SP6DS2D7 / SP6DS7 /

SP6DSSTB7 MED Series

Specialty all-refrigerators (drawers or glass doors)

• CP35LL MED Series

Compact refrigerator-freezers

• FCL44 / FS30L / FS60ML / FS407L / FS408BL MED Series

Compact and mid-size storage all-freezers

• VT65ML // SCFF51OSWH MED / ACF48WMEDDT Series

Low-temperature freezers // Built-in frost-free freezers

• FS20L / FS21L / FS22L / FS24L MED Series

All-freezers (-20°C)

Model numbers with “DT” indicate units having a Digital Thermostat

Table of Contents

Model Numbers ......................................................................... 1

Appliance Safety ....................................................................... 3

Proper disposal of an old appliance ..................................... 3

Installation Instructions ........................................................... 4

Key Eject lock ....................................................................... 4

Location Requirements ...................................................... 5 – 6

Location ................................................................................ 5

Recommended grounding method ....................................... 5

Leveling your appliance ....................................................... 6

When using the appliance .................................................... 6

Energy-saving tips ................................................................ 6

Appliance Care .................................................................... 7 – 8

Cleaning a frost-free appliance ............................................ 7

Cleaning a cycle defrost or manual defrost appliance ......... 7

Base grill ............................................................................... 8

Changing the light bulb ........................................................ 8

Loss of power ....................................................................... 8

Moving the appliance ........................................................... 8

Temperature Selection and Monitoring .......................... 9 – 12

Manual (dial) thermostat ...................................................... 9

Digital thermostat (on certain models) ................................ 10

Digital thermostat (SCR610BL & SCR1156) .............. 10 – 11

Traceable thermometer (PLUS models) ............................. 12

Traceable thermometer/alarm (MED models)............. 12 – 13

Keypad Lock ........................................................................... 14

About the Fixed Shelf ............................................................. 14

Operation of Specific Models ................................................ 15

Troubleshooting ..................................................................... 16

Limited Warranty .................................................................... 17

Appliance Safet

Your safety and the safety of others are very important to us.

We have provided many important safety messages in this manual and on your

appliance. Always read and obey all safety messages.

You can be seriously injured or even killed if you don’t follow instructions.

Safety messages will tell you what the potential hazard is, how to reduce the

chance of injury, and what can happen if the instructions are not followed.

• Plug into a grounded 3-prong outlet.

• Do not remove ground prong, nor use a 3/2 adapter.

• Do not use an extension cord.

• Use care not to plug into outlets controlled by wall switches.

• Disconnect power before servicing.

• After servicing, replace all parts and panels before operating.

• Use nonflammable cleaners.

• Keep flammable materials and vapors, such as gasoline, away from

appliances.

• Use two or more people to move and install appliance.

NOTE: Drawer refrigerators are provided with anti-tip brackets. Always install

prior to use.

Proper disposal of an old appliance

Old appliances can represent a suffocation hazard to children.

Remove doors from your old appliance.

Leave shelves in place.

If an old appliance contains refrigerants, it must be recycled by a licensed service

or disposal company.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock or injury

when using your appliance, follow these basic precautions:

Excessive Weight Hazard !

Installation Instructions

Use two or more people to move and install your appliance.

Failure to do so can result in back or other injury.

ALLOW APPLIANCE TO SIT UPRIGHT FOR 24 HOURS BEFORE TURNING ON, TO

ALLOW THE COMPRESSOR LUBRICANT TO DRAIN.

1. Remove packaging materials.

2. Remove tape and glue residue from surfaces before turning on the appliance.

Rub a small amount of liquid dish soap over the adhesive with your fingers.

Rinse with warm water and dry.

3. Do not use sharp instruments, rubbing alcohol, flammable fluids, or abrasive

cleaners to remove tape or glue. These products can damage the surface of

your appliance.

When Moving Your Appliance

Your appliance is heavy. When moving the appliance for cleaning or service,

be sure to protect the floor. Always pull the appliance straight out when

moving it. Do not wiggle or “walk” the appliance when trying to move it,

because floor damage can occur.

Clean Before Using

6. Some upright models have leveling legs. Level as necessary for best

operation.

After you remove all of the packaging materials, clean the inside of your

appliance before using it. See cleaning instructions in Appliance Care.

7. If your appliance has casters, after moving into place, lock the brakes on

those casters supplied with brakes. Always unlock before moving the

appliance for cleaning.

Key Eject lock (some models)

To lock or unlock the appliance, you must hold the key in the lock while turning.

The lock is spring loaded, so the key cannot be left in the lock.

If the key is lost, contact your dealer or SUMMIT APPLIANCE for a replacement.

Always give the model and serial number of your appliance when requesting a

replacement key. Keys for most models can be ordered online at

www.summitappliance.com/support

Keep flammable materials and vapors, such as gasoline, away

from appliances. Failure to do so can result in fire, explosion or

death.

Location Requirements

Location

IMPORTANT: Do not install the appliance near an oven, radiator, or other heat

source, nor in a location where the temperature will fall below 40°F (5°C). Do not

place in direct sunlight.

Check the strength of the floor before installing your appliance. It should hold the

weight of a fully loaded appliance. Allow at least 4” (10 cm) of airspace at the top

and on both sides of the appliance and also 4” between the back of the appliance

and the wall. If the appliance is going to be placed next to a wall, leave extra

space on the hinge side so the door can open wider than its width.

NOTE: Allow 4” (10 cm) clearance at the top and sides and a ¼” (0.64 cm)

clearance between appliances. IF YOUR MODEL HAS THE LETTERS “BI”

IN THE SUFFIX, IT IS DESIGNED FOR BUILT-IN USE AND REQUIRES

ONLY

MINIMAL

CLEARANCES EXCEPT AT THE BACK WHERE AT

LEAST 2” OF CLEARANCE SHOULD BE ALLOWED. ALL FF590 AND

SCFF51OSWH MODELS ARE ALSO BUILT-IN CAPABLE

• Plug into a grounded 3-prong outlet.

Electrical Shock Hazard

• Do not remove ground prong.

• Do not use an adapter.

• Do not use an extension cord.

Failure to follow these instructions can result in fire, electrical shock or

death.

Recommended grounding method

A 115 Volt (AC only) 60 Hz grounded electrical supply with a 15- or 20- amp fuse

or circuit breaker is required. It is recommended that a separate circuit serving

only your appliance be provided. Use outlets that cannot be turned off by a

switch or pull chain. Do not use an extension cord.

Leveling your appliance

Locate the two front leveling legs that may be taped among the packing materials. (In

many models these legs are already mounted into the underside of the appliance.)

(some upright models):

1. Screw these legs into the front holes on the bottom of the appliance. The back of

the appliance rests on two fixed supports. (Built-in models also have rear level

legs that can provide more precise leveling).

2. Adjust the front legs just enough to lift the cabinet up off the floor.

Note: If your model is equipped with front rollers, the front legs should be lowered

enough to lift the rollers off the floor to ensure the appliance does not roll

forward when the door is opened.

3. Place a leveling tool on top of the appliance, first side to side, then front to back.

Turn leg counter-clockwise to raise a corner. Turn leg clockwise to lower a corner.

4. Repeat Step 3 until appliance is level.

5. After appliance is fully loaded, recheck with level as in Step 3.

6. If your appliance is equipped with casters, the two front casters have brakes to

prevent rolling. Keep brakes locked, and unlock for moving only.

When using the appliance

In order to ensure proper temperature, you need to permit proper airflow in the

appliance. Do not block off any air vents. If the vents are blocked, airflow will be

hindered, and temperature and moisture problems may occur. Always position

contents to allow some airflow between shelves or baskets.

Allow the appliance to cool at least 6 to 8 hours before adding contents. Allow 24

hours for temperature to stabilize.

NOTE: When the appliance is first started, the compressor will run constantly until the

appliance is cooled. It may take 6 to 8 hours (or longer), depending on room

temperature and the number of times the appliance door is opened. After the

appliance has cooled, the compressor will turn on and off as needed to keep the

appliance at the proper temperature.

For optimum temperature performance, it is recommended that this unit be at

least 30% full during use. If you are only using this unit to store small loads, we

recommend adding some water bottles or freezer packs to ensure temperature

stability.

The outside of your appliance may feel warm. This is normal. The appliance’s design

and main function is to remove heat from packages and air space inside the

appliance. The heat is transferred to the room air, making the outside of the appliance

feel warm. (In some models the condenser that gets warm is just inside the side walls,

making these walls warm to the touch.)

ENERGY-SAVING TIPS

• The more airflow provided around an appliance, the less energy it will use.

• If your appliance requires manual defrosting, keep ice build-up to less than 1/2".

• Keep doors open a minimum of time, and shut securely.

Appliance Care

Cleaning a frost-free appliance

Use nonflammable cleaners.

Frost-free means that you do not have to defrost your appliance. Frost is removed by

air moving and collecting any moisture and depositing it on the cooling coil. The

cooling coil periodically warms up enough to melt the frost, and the water then flows

down to the drain pan (located behind the base grill) where it is evaporated.

Complete cleaning should be done at least once a year.

1. Unplug appliance or disconnect power.

2. Remove all stored items, plus shelves, trays, etc.

3. Wash the inside walls, shelves and trays with a solution of mild detergent in warm

water or 2 tbsp (26 g) baking soda to 1 qt (0.95 L) warm water.

• Do not use abrasive or harsh cleaners such as window sprays, scouring

cleansers, flammable fluids, cleaning waxes, concentrated detergents,

bleaches or cleansers containing petroleum products on plastic parts, interior

and door liners or gaskets. Do not use paper towels, scouring pads, or other

harsh cleaning tools. These can scratch or damage surfaces.

4. Rinse well and wipe dry with a clean soft cloth.

5. Use the appropriate cleaning method for the exterior finish.

Painted metal

6. Plug in appliance or reconnect power.

: Wash exteriors with a clean sponge or soft cloth and a mild

detergent in warm water. Do not use abrasive or harsh cleaners, or cleaners

designed for stainless steel. Dry thoroughly with a soft cloth. For additional

protection against damage to painted metal exteriors, apply appliance wax (or

auto paste wax) with a clean, soft cloth. Do not wax plastic parts.

7. Replace all containers.

Cleaning a cycle defrost or manual defrost refrigerator

Cycle defrost models utilize a system where ice builds up on the rear wall and melts

when the compressor is off. Manual defrost models continually build ice on inner

walls.

NEVER USE A METAL OBJECT TO REMOVE ICE FROM THE REAR WALL.

IF NEEDED, USE A PLASTIC ICE-SCRAPER OR A HAIR DRYER.

Clean surfaces using the same instructions as for frost-free models.

For CSS Models (completely stainless steel), only use cleaners especially made

for stainless steel.

Base grill

To Remove and Replace the Base Grill:

(some models only):

1. Open the appliance door and remove the base grill by pulling down and out

from the top.

2. Replace the base grill by putting the clips in the openings in the appliance

panel. Push in until the base grill snaps into place.

Changing the light

bulb

NOTE: Not all appliance bulbs will fit your appliance. Be sure to replace the bulb

with one of the same size, shape, base size and wattage. You can purchase

bulbs from www.summitappliance.com/support

(some models only):

1. Unplug appliance or disconnect power.

2. Remove the light shield. Most models do not require tools.

3. Replace the light bulb with an appliance bulb of the same wattage.

4. Replace the light shield.

5. Plug in appliance or reconnect power.

Loss of power

After the power is restored, unplug the appliance for 30 minutes to allow the

refrigeration system to equalize. During this time, keep the door closed as much

as possible.

Remember: A full appliance stays cold longer than a partially filled one.

Moving the appliance

1. Remove stored items and tape shelves, drawers and trays in place.

2. Unplug the appliance.

3. Clean it thoroughly.

4. Tape the appliance shut and tape the electrical cord to the cabinet.

When you get the appliance to its new location, refer to the Installation

Instructions and Temperature Selection sections for information on installation

and setting the controls.

YOUR APPLIANCE MAY HAVE A MECHANICAL (DIAL) OR DIGITAL THERMOSTAT.

DIAL INSTRUCTIONS ARE BELOW. DIGITAL INSTRUCTIONS ARE ON PAGE 10.

Temperature Selection and Monitoring

Manual (dial) thermostat

Your refrigerator may be controlled with a thermostat knob located inside the unit,

towards the right-hand corner. Turn the knob clockwise from the STOP (0) position

toward the higher numbers for colder temperatures.

(on most models):

Setting the Temperature:

• Higher settings on the knob (higher numbers) mean lower temperatures

(colder) in all compartments of the appliance. The temperature inside a

refrigerator may even drop below 32°F. Use higher thermostat settings only

when required or recommended. When the ambient temperature is normal,

we recommend a medium setting.

• Changes of the ambient temperature affect temperature in the interior of the

appliance, so keep this in mind when choosing the setting of the thermostat

dial.

• At STOP (0) position, the appliance does not operate (the cooling system is

switched off), but the power supply is not interrupted (the light is on when you

open the refrigerator door).

• The temperatures in the refrigerator and freezer compartments also depend

on how often you open the door.

In all small refrigerators and freezers without interior fans, temperatures are

coldest near the bottom, and occasionally near the rear. Place contents

accordingly.

For optimum temperature performance, it is recommended that this unit be at

least 30% full during use. If you are only using this unit to store small loads,

we recommend adding some water bottles or freezer packs to ensure

temperature stability.

Digital thermostat

If you find it necessary to change the temperature setting for your digital-thermostat

controlled appliance, please refer to the following instructions. The front panel of the

thermostat is illustrated here:

(on certain models):

To see the SET POINT:

Push and immediately release the SET key. The display will show the SET POINT

value. Wait 5 seconds and the probe value will display again.

To change the SET POINT:

Push and hold the SET key for more than 3 seconds to change the set point value.

The value of the set point will be displayed, and the “snowflake” LED will start

blinking.

To change the SET value:

Push the UP or DOWN arrow to the desired setting. The new setting will be

memorized after 15 seconds, provided no other keys are pushed.

NOTE: The minimum and maximum range of your thermostat is preset and

locked by us, so it cannot easily be accidentally moved between freezer and

refrigerator temperatures. To reset this range lock, either call us or find

information on our website under Troubleshooting.

Digital thermostat

ON/OFF Power:

(SCR610BL & SCR1156 models):

To turn the appliance ON or OFF, touch the symbol

and hold for 5 seconds.

NOTE: Pressing the POWER key once can switch off the

audible alarm when the alarm is on.

UP :

Used to increase (warm) the set temperature by 1°C/1ºF.

DOWN :

Used to decrease (cool) the set temperature by 1°C/1ºF.

Interior Light :

Touching the LIGHT symbol toggles between 2 modes of operation for the internal

lights: functional (default) mode and showcase mode. If you are in functional (default)

mode, the lights will turn on only when the door is open. If you are in showcase mode,

the lights will be on whether or not the door is open.

ºF/ºC Selector:

Select the temperature display in Fahrenheit or Celsius degrees. To change the

temperature from Fahrenheit to Celsius or from Celsius to Fahrenheit, press and hold

the LIGHT key for 5 seconds.

melting

snowflake

UP & DOWN arrows

SET key

snowflake

Control panel

Setting the Temperature Control:

• You can set the temperature by touching the UP and DOWN symbols. When you

push either of the two buttons for the first time, the LED readout will show the

original temperature set previously. (The temperature preset at the factory is 38°F,

or 3°C.)

• The temperature you are setting will increase by one degree each time you touch

the UP symbol, and will decrease by one degree each time you touch the DOWN

symbol.

• The range of the temperature control is from 36°F to 43°F (2°C to 6°C).

• To view the set temperature at any time, touch the UP or DOWN symbol. The set

temperature will flash in the display window for 5 seconds. After 5 seconds, the

temperature inside the unit will reappear in the display window.

Sabbath Mode:

Sabbath mode is available for the observance of certain religious holidays. This mode

turns off the displays, interior light and audible alarms and prevents them from turning

on again. Normal cooling operations will still take place.

To initiate Sabbath mode, press the POWER and LIGHT keys at the same time for at

least 5 seconds. The indicator light will flash four times and confirm the Sabbath mode

is ON.

Sabbath mode can be exited by repeating the above process. The Sabbath Mode will

automatically exit after 96 hours.

Temperature Memory Function:

In the event of a power interruption (power surge, breaker switch, etc.), the unit can

remember the previous temperature settings. When power is recovered, the cabinet

will return to the same set temperature as before the power went off.

Temperature Alarm / Door Alarm:

• An audible alarm sounds if the storage temperature is not cold enough. The

temperature display flashes at the same time.

• The cause of the temperature being too high may be:

- Warm items were placed inside

- Too much warm ambient air flowed in when rearranging and removing contents

- Power failure for some time

- The appliance is faulty.

• The audible alarm is automatically silenced and the temperature display stops

flashing when the temperature is sufficiently cold again.

• If the door has been left open for more than 60 seconds, the alarm will sound.

Pressing the POWER key once can switch off the audible alarm.

Traceable thermometer

This digital thermometer simultaneously displays

maximum, minimum and current temperatures.

The Max/Min feature monitors and stores the

highest and lowest readings since the battery

was inserted or since the RESET button was last

pressed.

(PLUS models):

The temperature sensor, or probe, is enclosed in

a glycol-filled bottle that you insert into the

location to be monitored, such as inside a

refrigerator or freezer. The thermometer itself

can be attached to the door of the unit with the

magnet on the back, or it can be placed on a

convenient table or shelf.

Power to the Traceable Thermometer is supplied with a AAA lithium battery. When it

is inserted correctly, all segments of the LCD display are temporarily activated. When

the battery needs to be replaced, a battery symbol will flash on the display.

The temperature display can be switched between Celsius (°C) and Fahrenheit (°F)

with a push of the

°C/°F button. The display will alternate between refrigerator (probe)

temperature and room temperature when you press the

ROOM/FRIDGE button. Press

RESET to clear the Max/Min temperature record.

See instruction pamphlet for more information about the Traceable Thermometer.

Traceable thermometer/alarm

Every MED unit is equipped with a Traceable

Thermometer/Alarm that simultaneously displays

minimum, maximum and current interior

temperatures and provides a visual and audible

signal when the temperature inside the unit falls

outside the set temperature range.

(MED models):

The temperature sensor, or probe, is enclosed in

a glycol-filled bottle that you insert into the

location to be monitored, such as inside a

refrigerator or freezer, once the unit has been

programmed. The thermometer/alarm itself can

be attached to the door of the unit with the

magnet on the back, or it can be placed on a

convenient table or shelf.

Power to the Traceable Thermometer/Alarm is supplied with a lithium iron disulfide

battery with a 10-year shelf life. When it is inserted correctly, the unit will beep and all

segments of the LCD display will be temporarily activated. (Note that alarm

temperatures will have to be reset after replacing the battery.)

The temperature display can be switched between Celsius (°C) and Fahrenheit (°F)

by sliding the

°C/°F button located on the back of the unit.

Thermometer/alarm instructions

Function of Controls:

(cont’d):

MODE/RESET Key: Press ONCE to reset Max/Min temperature record. When the unit

is sounding an alarm, press ONCE to turn off the beeping sound.

HIGH/LOW Key: Press ONCE to display high alarm setting. Press TWICE to display

low alarm setting. Press THREE TIMES to display current temperature reading.

ALERT ON/OFF Key

Programming the Alarms:

: When the unit is sounding an alarm, press ONCE to turn off.

However, the High-Alarm or Low-Alarm will still flash until the temperature goes

back to normal or the Alarm function is turned off.

The thermometer displays the internal temperature of the unit being monitored, as

well as the maximum and minimum temperatures reached. The maximum and

minimum readings reflect the highest and lowest temperatures since the battery was

inserted or since the MODE/RESET key was last pressed. If the temperature rises

above or falls below the set temperature range, the alarm will sound. By default, the

high alarm temperature setting is 8°C (46.4°F) and the low alarm temperature setting

is 2°C (35.6°F). To reset these limits, follow these instructions:

High Alarm Temperature Setting: Press the HIGH/LOW key ONCE, then press

MODE/RESET to enter the High Alarm temperature setting mode. Use the Up and

Down arrows to adjust the temperature accordingly. Press MODE/RESET once

again to confirm the setting.

Low Alarm Temperature Setting

By default, the low and high alarms should be audible. To turn alarms on/off:

: Press the HIGH/LOW key TWICE, then press

MODE/RESET to enter the Low Alarm temperature setting mode. Use the Up and

Down arrows to adjust the temperature accordingly. Press MODE/RESET ONCE to

confirm the setting.

Audible High Alarm Setting: To make sure the high alarm is audible, press HIGH/LOW

key ONCE (to activate HI-SET on the screen). Then press the ALERT ON/OFF key

ONCE to activate the HIGH-ALARM beeping sound. Press again to deactivate.

Audible Low Alarm Setting

NOTE: For an activated high alarm and low alarm

buzzer, the display should indicate HI-ALARM

and LO-ALARM as shown here.

: To make sure that the low temperature alarm is audible,

press the HIGH/LOW key TWICE to activate LOW-SET on the screen. Then press

the ALERT ON/OFF key ONCE to activate the LOW-ALARM beeping sound. Press

again to deactivate.

More details about the features and usage of the Traceable Thermometer/Alarm can

be found in the User Manual accompanying the unit.

Keypad Lock

(optional on most models)

Factory-set default password: The factory-set default password is 0123. If the default

password is lost, press the key (located inside the battery box) for

seconds, then wait for the warning sound which signifies the factory-set

default password has been restored.

To set the password

NOTE: Each password starts with a number from 0 to 9 in order. The first password starting

with 0 is the default password. For example, use 1xxx, then 2xxx etc. for 10 users.

: While door is open, press the key (located

inside the battery box) until it jingles, enter the 0123 password, then #

within 10 seconds to confirm. Enter your password (1-16 digits), then

press # again to confirm. A total of 10 passwords can be set.

Changing password

NOTE: The first digit cannot be changed.

: While the door is open, press the key (located inside the battery

box) until it jingles, enter the old password and press # within 10 seconds to confirm. Enter

the new password, then press # to confirm.

To open the door: While the door is closed, press the START/END key, enter the

password, then press START/END

again to confirm.

To lock door manually: Press #.

Function setting of automatic lock: Setting of the auto-lock time: Press the key

(inside the battery box), enter a number (any number between 10-99), then press # to

confirm. The auto-lock time can be set between 10-99 seconds after opening the door. If

the time is set less than 10 seconds, the door will not lock automatically, only manually.

Deleting the door-opening passwords

NOTE: To access the battery box you need to remove only the two small screws on the top

and bottom of that cover. Do not remove the 4 screws holding the keypad and cover to

the appliance door.

: Press the START/END

key, enter default

password followed by 0000, then press # and all the door-opening passwords will be

deleted except for the default password.

About the Fixed Shelf

In some units, the center shelf is fixed in place and

cannot be removed (see image). This is because the

glycol-filled bottle that contains the temperature

sensors for your alarm and thermometer is best

stored in this location. The center of your refrigerator

or freezer will provide the most accurate

temperature readings. For proper temperature

monitoring, keep the bottles in place and do not

remove this shelf.

Operation of Specific Models

SCFF51OSWH MED and ACF48WMEDDT Series

These frost-free all-freezers can be built-in or free-standing. They do not require defrosting

and have a digital thermostat, LED lighting and a lock. At the top of the unit is a cooling

system that uses a fan to provide cold air. For best operation, do not block the air flow with

contents.

FF6L, FF7L, FF28LWH, FF31L7, FF511L, FF521BL, FF590SSHH, FFAR2L, FFAR10,

FFAR21L, FFAR24L, FFAR25L7, SCR450L, SCR500BL, SCR600L, SCR610BL,

SCR1156 PLUS & MED Series; SP6DS2D7, SP6DS7, SP6DSSTB7 MED Series only

These models are all-refrigerators (no freezer compartment) with automatic defrost. All

have cold plates on the rear wall, and the coldest spots in the refrigerator will be in the rear

and toward the bottom. All have interior fans to promote even cooling. In the rear bottom

above the step, there is a drain line to allow defrost water to exit the refrigerator. Keep this

drain line clear, or icing inside the refrigerator will occur. FF7, FF31L7, FF511L, FF521BL,

FFAR25L7 and SCR series models have lights that are not door-activated, and are

controlled either by a rocker switch on the top right or a Light switch on the control panel.

The light generates a small amount of heat, so minimize the use of the light for best

operation and energy savings. FF6 models and FFAR10 models all have door-activated

lights. Smaller models and drawer models do not have interior lights.

NOTE: FF590, models with BI in the model number, and all drawer units are designed for

built-in operation and need very little clearance on the sides and above the units.

All

other models

FCL44, FS20L, FS21L, FS22L, FS24L, FS30L, FS60ML, FS407L, FS408BL, VT65ML

PLUS & MED Series

require at least 1 inch of airflow on the sides and above the units. All

models operate best when 2 inches is provided between the rear wall and the back of

the unit.

Model FCL44 is a chest freezer; all of the others are upright. These are manual defrost all-

freezers. No internal fans are present, and ice will build up along the cooling coils.

Periodically defrost the ice (recommended when the ice level reaches a thickness of 1/4 to

1/2 inch). NEVER USE A METAL INSTRUMENT as you can damage the cooling coils,

which will void your warranty and often cannot be repaired. To defrost, disconnect from the

power supply, empty the contents, provide a tray in the bottom to collect water, and use a

hairdryer or other source of warm air to melt the ice (or leave the door open and the power

off for 24 to 48 hours). For built-in (BI) models and clearance information, see NOTE

above.

CP35LL PLUS & MED Series; CT66 PLUS Series only

These models are cycle defrost refrigerator-freezers. The freezers are designed to operate

at 0°F (-18°C), suitable for medical or laboratory uses. These models have dual

evaporators to maintain separate temperatures in the freezer and refrigerator. Defrost the

freezer carefully, as directed above for manual defrost. The refrigerator section operates in

the normal range (35 to 45°F, or 2 to 7°C) and defrosts automatically. For built-in (BI)

models and clearance information, see NOTE above.

CM411L, CM421BL, S19LWH PLUS Series

These models are manual defrost refrigerator-freezers. The freezers in these models are

designed to operate at 25°F (-4°C) to keep ice frozen, and not for medication or products

needing colder temperatures. Defrost carefully, following directions above. The refrigerator

section will operate in the normal range (35 to 45°F, or 2 to 7°C) and is suitable for most

refrigerated products. For built-in (BI) models and clearance information, see NOTE above.

Try these solutions first to avoid the cost of an unnecessary service call.

Troubleshooting

Your appliance will not operate:

•

Has a household fuse blown or circuit breaker tripped?

Replace the fuse or reset the circuit breaker.

• Is the freezer defrosting (on some models)?

Recheck to see whether the freezer is operating in 30 minutes. Your freezer will regularly run an

automatic defrost cycle.

There is water in the defrost drain pan (on some models):

•

Is the freezer defrosting?

The water will evaporate. It is normal for water to drip into the defrost pan.

• Is it more humid than normal?

When it is humid, expect that the water in the defrost pan will take longer to evaporate.

The motor seems to run too much:

•

Is there excessive frost or a package preventing the door from closing?

Defrost and clean the freezer, or move the package so the door closes properly.

• Is the room temperature hotter than normal?

The motor will run longer under warm conditions. At normal room temperatures, the motor will run

about 40% to 80% of the time. Under warmer conditions, it will run even more.

• Has a large amount of food just been added to the freezer?

Adding a large amount of food warms the freezer. The motor normally will run longer to cool the

freezer back down.

• Is the door closed completely?

Push the door firmly shut. If it will not shut all the way, see The door will not close completely later

in this section.

• Are the condenser coils dirty (on some models)?

This prevents heat transfer and makes the motor work harder. Clean the condenser coils.

• Is the door gasket sealed all the way around?

If not, contact a qualified technician.

NOTE: If the problem is not due to any of the above, remember that the compressor on your new

appliance will operate longer than your old one due to its high-efficiency motor.

Temperature is too warm:

•

Are the air vents blocked?

This prevents cold air movement. Move objects away from the air vents.

• Is the door opened often?

Be aware that the freezer will warm when this occurs. In order to keep the freezer cool, try

to get everything you need out of the freezer at once, keep food organized so it is easy to

find, and close the door as soon as the food is removed.

• Has a large amount of food just been added to the freezer?

Adding a large amount of food warms the freezer. It can take several hours for the freezer to

return to the normal temperature.

The door will not close completely or is difficult to open:

•

Are food packages blocking the door?

Rearrange containers so that they fit more tightly and take up less space.

• Are the shelves or drawers out of position (on some models)?

Put the shelves and drawers back into their correct positions.

Limited Warranty

Within the 48 contiguous United States, for one year from the date of purchase, when this appliance is

operated and maintained according to instructions attached to or furnished with the product, warrantor

will pay for factory-specified parts and repair labor to correct defects in materials or workmanship.

Service must be provided by a designated service company. Outside the 48 states, all parts are

warranted for one year from manufacturing defects. Plastic parts, shelves and cabinets are warranted to

be manufactured to commercially acceptable standards, and are not covered from damage during

handling or breakage.

ONE YEAR LIMITED WARRANTY FOR APPLIANCE

1. The compressor is covered for 5 years.

5-YEAR COMPRESSOR WARRANTY

2. Replacement does not include labor.

ITEMS WARRANTOR WILL NOT PAY FOR:

Service calls to correct the installation of your appliance, to instruct you how to use your appliance, to replace or

repair fuses or to correct wiring or plumbing.

2. Service calls to repair or replace appliance light bulbs or broken glass shelves. Consumable parts (such as filters)

are excluded from warranty coverage.

3. Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation, installation

not in accordance with electrical or plumbing codes, or use of products not approved by warrantor.

4. Replacement parts or repair labor costs for units operated outside the United States.

5. Repairs to parts or systems resulting from unauthorized modifications made to the appliance.

6. Expenses for travel and transportation for product service in remote locations.

7. The removal and reinstallation of your appliance if it is installed in an inaccessible location or is not installed in

accordance with published installation instructions.

CUSTOMER’S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE

PRODUCT REPAIR AS PROVIDED HEREIN. IMPLIED WARRANTIES, INCLUDING WARRANTIES OF

MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR.

WARRANTOR SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. SOME

STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR

CONSEQUENTIAL DAMAGES, OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES

OF MERCHANTABILITY OR FITNESS, SO THESE EXCLUSIONS OR LIMITATIONS MAY NOT

APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO

HAVE OTHER RIGHTS, WHICH VARY FROM STATE TO STATE.

DISCLAIMER OF IMPLIED WARRANTIES – LIMITATION OF REMEDIES

FELIX STORCH, INC.

770 Garrison Avenue

Bronx, New York 10474

Phone: (718) 893-3900

Fax: (844) 478-8799

www.summitappliance.com

For parts and accessory ordering,

troubleshooting and helpful hints,

visit:www.summitappliance.com/support

July 2016

WARNING! This product may contain chemicals known to the state of

California to cause cancer or birth defects or other reproductive harm. For

more information, visit: www.summitappliance.com/prop65

Chemicals known by the manufacturer to be present in this product in

concentrations higher than threshold limits: NONE.

Série PLUS

Réfrigérateurs et congélateurs pour l'entreposage générale

Si vous avez besoin de service ou appelez avec une question,

avoir cette information prête. Nous vous conseillons de

conserver ce manuel en votre possession.

Modèle : __________ N° de série : _________________

Options ajoutées : __________________________________

Date d'achat : _______ Concessionnaire : ___________

Pour des pièces : visitez notre site Web

Série MED/MEDDT

Réfrigérateurs et congélateurs pour le stockage médical

FELIX STORCH, INC.

Enregistrée avec ISO 9001: 2008

770 Garrison Avenue

Bronx, New York 10474

medicalrefrigerators.com

MODE D’EMPLOI

par

Numéros de modèle

Modèles PLUS

• Série FF6 / FF7 / FF28LWH / FF31L7 / FF511L / FF521BL / FFAR2L / FFAR21L /

FFAR24L / FFAR25L7 / FF590SSHH PLUS

Tout-réfrigérateurs à dégivrage automatique ou fonctionnement sans givre

• Série VT65ML PLUS

Congélateurs à basse température

• Série FFAR10 PLUS

Tout-réfrigérateurs grand format de stockage

• Série FS20L / FS21L / FS22L / FS24L PLUS

Tout-congélateurs compacts (-20 °C)

• Série CM411L / CM421BL / CP35LL / CT66 / S19LWH PLUS

Réfrigérateur-congélateurs compacts

• Série FCL44 / FS30L / FS60ML / FS407L / FS408BL PLUS

Tout-congélateurs de stockage compacts et de taille moyenne

• Série SCR450L / SCR500BL / SCR600L / SCR610BL / SCR1156 PLUS

Tout-réfrigérateurs avec portes en verre

Modèles MED/MEDDT*

• Série FF6 / FF7 / FF28LWH / FF31L7 / FF511L / FF521BL / FF590SSHH / FFAR2L /

FFAR21L / FFAR24L / FFAR25L7 MED

Tout-réfrigérateurs à dégivrage automatique ou fonctionnement sans givre

• Série FFAR10 MED

Tout-réfrigérateurs grand format de stockage

• Série SCR450L / SCR500BL / SCR600L / SCR610BL / SCR1156 / SP6DS2D7 /

SP6DS7 / SP6DSSTB7 MED

Tout-réfrigérateurs spécialisés (tiroirs ou des portes en verre)

• Série CP35LL MED

Réfrigérateur-congélateurs compacts

• Série FCL44 / FS30L / FS60ML / FS407L / FS408BL MED

Tout-congélateurs de stockage compacts et de taille moyenne

• Série VT65ML // SCFF51OSWH MED / ACF48WMEDDT

Congélateurs à basse température // Congélateurs encastrés sans givre

• Série FS20L / FS21L / FS22L / FS24L MED

Tout-congélateurs (-20°C)

* Les numéros de modèle avec "DT" indiquent les unités ayant un

thermostat numérique (D

igital Thermostat).

La page charge ...

Summit SCR450L MED Series Manuel utilisateur

Marque: Summit

Modèle: SCR450L MED Series

Catégorie: Frigos

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Summit SCR450L MED Series User manual

Summit SCR450L MED Series Manuel utilisateur

Summit SCR450L MED Series Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents