Zephyr AK1200BB Hood User Manual

Use, Care, and Installation Guide

www.zephyronline.com

Model number:

Serial Number:

Date of Purchase:

Sales Dealer:

JUN17.0201 © Zephyr Ventilation LLC.

Breeze I

Breeze II

Breeze I

AK1124x, AK1100x, AK1136x

Breeze II

AK1200Bx, AK1236Bx

READ AND SAVE THESE INSTRUCTIONS

www.zephyronline.com

1

SAFETY NOTICE ................................................................. 2-3

LIST OF MATERIALS ....................................................... 4

INSTALLATION

Ducting Calculation Sheet

....................................... 5

Mounting Height & Clearance

................................ 6

Ducting Options

........................................................... 7

6SHFL¿FDWLRQV

............................................................... 8

Preparing Electrical

.................................................... 9

Preparing Electrical and Ducting

.......................... 10

Converting to Air Recirculating Mode

................. 11-12

Mounting the Range Hood ............................. 13

FEATURES & CONTROLS

Controls & Features

................................................... 14

MAINTENANCE

Cleaning and Filter Removal

.................................. 15

Lights

................................................................................ 16

TROUBLESHOOTING

................................................................ 17

WIRING DIAGRAMS

................................................................... 18

LIST OF PARTS AND ACCESSORIES

.............................. 19

WARRANTY

.................................................................................... 20

PRODUCT REGISTRATION

.................................................... 21

Table of Contents

Important Safety Notice

READ AND SAVE THESE INSTRUCTIONS

2

www.zephyronline.com

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT USE THIS FAN WITH ANY SOLID-STATE CONTROL DEVICE.

WARNING

TO REDUCE THE RISK OF FIRE ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:

a. Use this unit only in the manner intended by the manufacturer, if you have questions, contact the manufacturer.

b. Before servicing or cleaning unit, switch power off at service panel and lock panel to prevent power from being switched on accidentally.

When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service

panel.

CAUTION

For general ventilating use only. Do not use to exhaust hazardous or explosive materials and vapors. Take care when using cleaning

agents or detergents. Suitable for use in household cooking area.

WARNING

TO REDUCE THE RISK OF RANGE TOP GREASE FIRE:

a. Never leave surface units unattended at high settings. Boilovers cause smoking and greasy spillovers that may ignite. Heat oils slowly

on low or medium settings.

E $OZD\VWXUQKRRG21ZKHQFRRNLQJDWKLJKKHDWRUZKHQÀDPLQJIRRG

F &OHDQYHQWLODWLQJIDQVIUHTXHQWO\*UHDVHVKRXOGQRWEHDOORZHGWRDFFXPXODWHRQIDQRU¿OWHU

d. Use proper pan size. Always use cookware appropriate for the size of the surface element.

H .HHSIDQ¿OWHUVDQGJUHDVHODGHQVXUIDFHVFOHDQ

f. Use high setting on hood only when necessary.

g. Don’t leave hood unattended when cooking.

h. Always use cookware and utensils appropriate for the type of and amount of food being prepared.

WARNING

TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE TOP FIRE, OBSERVE THE FOLLOWING:

D 6027+(5)/$0(6ZLWKDFORVH¿WWLQJOLGFRRNLHVKHHWRUPHWDOWUD\WKHQWXUQRIIWKHEXUQHU%(&$5()8/7235(9(17%8516

,IWKHÀDPHVGRQRWJRRXWLPPHGLDWHO\(9$&8$7($1'&$//7+(),5('(3$570(17

b. NEVER PICK UP A FLAMING PAN – You may be burned.

c. DO NOT USE WATER, including wet dishcloths or towels – a violent steam explosion will result.

d. Use an extinguisher ONLY if:

1. You know you have a Class ABC extinguisher, and you already know how to operate it.

 7KH¿UHLVVPDOODQGFRQWDLQHGLQWKHDUHDZKHUHLWVWDUWHG

 7KH¿UHGHSDUWPHQWLVEHLQJFDOOHG

 <RXFDQ¿JKWWKH¿UHZLWK\RXUEDFNWRDQH[LW

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:

D ,QVWDOODWLRQZRUNDQGHOHFWULFDOZLULQJPXVWEHGRQHE\TXDOL¿HGSHUVRQVLQDFFRUGDQFHZLWKDOODSSOLFDEOHFRGHVDQGVWDQGDUGV

,QFOXGLQJ¿UHUDWHGFRQVWUXFWLRQ

E 6XI¿FLHQWDLULVQHHGHGIRUSRZHUFRPEXVWLRQDQGH[KDXVWLQJRIJDVHVWKURXJKWKHÀXHFKLPQH\RIIXHOEXUQLQJHTXLSPHQWWRSUHYHQW

back-drafting. Follow the heating equipment manufacturer’s guideline and safety standards such as those published by the National

)LUH3URWHFWLRQ$VVRFLDWLRQ1)3$DQGWKH$PHULFDQ6RFLHW\IRU+HDWLQJ5HIULJHUDWLRQDQG$LU&RQGLWLRQLQJ(QJLQHHUV$6+5$(DQG

the local code authorities.

c. When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.

d. Ducted fans must always vent to the outdoors.

e. If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application and be connected to a GFI

*URXQG)DXOW,QWHUUXSWHUSURWHFWHGEUDQFKFLUFXLW

g. NEVER place a switch where it can be reached from a tub or shower.

h. Make sure the power is off before installing, wiring or maintenancing.

Important Safety Notice

3

WARNING

TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCTWORK.

NOT FOR USE OVER AN OUTDOOR GRILL.

CAUTION

7RUHGXFHULVNRI¿UHDQGWRSURSHUO\H[KDXVWDLURXWVLGH'RQRWYHQWH[KDXVWDLULQWRVSDFHVZLWKLQZDOOVFHLOLQJV

attics, crawl spaces or garages.

For indoor use only.

Do not use over cooking equipment greater than 60,000 BTU/hr.

This hood is not intended to be used as a shelf.

OPERATION

$OZD\VOHDYHVDIHW\JULOOHVDQG¿OWHUVLQSODFH:LWKRXWWKHVHFRPSRQHQWVRSHUDWLQJEORZHUVFRXOGFDWFKRQWRKDLU¿QJHUV

and loose clothing.

The manufacturer declines all responsibility in the event of failure to observe the instructions given here for installation,

maintenance and suitable use of the product. The manufacturer further declines all responsibility for injury due to

negligence and the warranty of the unit automatically expires due to improper maintenance.

*NOTE: Please check www.zephyronline.com for revisions before doing any custom work.

ELECTRICAL REQUIREMENTS

Important:

Observe all governing codes and ordinances.

It is the customer’s responsibility:

 7RFRQWDFWDTXDOL¿HGHOHFWULFDOLQVWDOOHU

- To assure that the electrical installation is adequate and in conformance with National Electrical Code, ANSI/NFPA 70

latest edition* or CSA standards C22.1-94, Canadian Electrical Code, Part 1 and C22.2 No.0-M91 - latest edition** and

all local codes and ordinances.

,IFRGHVSHUPLWDQGDVHSDUDWHJURXQGZLUHLVXVHGLWLVUHFRPPHQGHGWKDWDTXDOL¿HGHOHFWULFLDQGHWHUPLQHWKDWWKH

ground path is adequate.

Do not ground to a gas pipe.

&KHFNZLWKDTXDOL¿HGHOHFWULFLDQLI\RXDUHQRWVXUHWKHUDQJHKRRGLVSURSHUO\JURXQGHG

Do not have a fuse in the neutral or ground circuit.

*National Fire Protection Association Batterymarch Park, Quincy, Massachusetts 02269

** CSA International 8501 East Pleasant Valley Road, Cleveland, Ohio 44131-5575

This appliance requires a 120V 60Hz electrical supply and connected to an individual properly grounded branch circuit

protected by a 15 or 20 ampere circuit breaker or time delay fuse. Wiring must be 2 wire with ground. Please also refer to

Electrical Diagram on product.

$FDEOHORFNLQJFRQQHFWRUQRWVXSSOLHGPLJKWDOVREHUHTXLUHGE\ORFDOFRGHV&KHFNZLWKORFDOUHTXLUHPHQWVSXUFKDVH

and install appropriate connector if necessary.

List of Materials

4

www.zephyronline.com

MODELS: BREEZE I - AK1124x, AK1100x, AK1136x

BREEZE II - AK1200Bx, AK1236Bx

PARTS SUPPLIED

1 - Hood

$OXPLQXPPHVK¿OWHUV

2 - Halogen light bulbs, GU-10 35W, Breeze I Only

1 - LED Light Strip, 5W, Breeze II Only

´[´UHFWDQJXODUVWDUWLQJFROODUZLWKGDPSHUORFDWHGLQVLGHKRRGERG\

1 - Hardware package

HARDWARE PACKAGE CONTENTS

PARTS NOT SUPPLIED

- Ducting, conduit and all installation tools

&DEOHFRQQHFWRUif required by local codes

5HFLUFXODWLQJ.LW$.

M4 x 1” (4)

M4 x 1-1/2” (4)

M4 x 2” (4)

M4 x 8 (10)

Wood screw washers (4)

Wire Caps (3)

Light bulb removal

Suction Cup (1)

Breeze I Only

5

Installation – Ducting Calculation Sheet

Duct pieces

Tot a l

Equivalent number

length x used =

3- 1/4” x 10”

Rect.,

straight

1 Ft. x ( ) =

Ft.

3- 1/4” x 10”

Rect. to

6” round

transition

5 Ft. x ( ) =

Ft.

3- 1/4” x 10”

Rect. to

6” round

transition

90

0

elbow

20 Ft. x ( ) =

Ft.

6”, 7”, 8”, 10”

Round,

90

0

15 Ft.

x ( ) =

Ft.

6”, 7”, 8”, 10”

Round,

45

0

9 Ft. x ( ) =

Ft.

6”, 7”, 8”, 10”

Round,

straight

1 Ft. x ( ) =

Ft.

Subtotal column 1 =

Duct pieces

Tot a l

Equivalent number

length x used =

6”, 7”, 8”, 10”

Round, wall

cap with

damper

30 Ft. x ( ) =

Ft.

6”, 7”, 8”, 10”

Round

roof cap

30 Ft. x ( ) =

Ft.

Subtotal column 2 =

Subtotal column 1 =

Total ductwork =

Maximum Duct Length: For satisfactory air movement,

the total duct length

should not exceed 100 equivalent feet.

6” round to

3- 1/4” x 10”

rect.

transition

1 Ft. x ( ) =

Ft.

6” round to

3- 1/4” x 10”

rect.

transition

90

0

elbow

16 Ft. x ( ) =

Ft.

7” round to

3 1/4” x 10”

rect.

transition

8 Ft. x ( ) =

Ft.

7” round to

3- 1/4” x 10”

rect.

transition

90

0

elbow

23 Ft. x ( ) =

Ft.

elbow

7” to 6” or

8” to 7” Round

tapered

reducer

25 Ft. x ( ) =

Ft.

3- 1/4” x 10”

Rect. 90

0

elbow

15 Ft. x ( ) =

Ft.

3- 1/4” x 10”

Rect. 45

0

elbow

9 Ft. x ( ) =

Ft.

3- 1/4” x 10”

Rect. 90

0

flat elbow

24 Ft. x ( ) =

Ft.

3- 1/4” x 10”

Rect.

wall cap

with damper

30 Ft. x ( ) =

Ft.

Ft. x ( ) =

Ft.

15

6”, 7“, 8”

Round

in-line

damper

Installation – Mounting Height & Clearance

6

www.zephyronline.com

DUCTING

A minimum 3-1/4” x 10” rectangular duct must be

XVHGWRPDLQWDLQPD[LPXPDLUÀRZHI¿FLHQF\

Always use rigid type metal ducts only. Flexible

GXFWVFRXOGUHVWULFWDLUÀRZE\XSWR

$OVRXVHFDOFXODWLRQRQSDJHWRFRPSXWHWRWDO

available duct run when using elbows, transitions

and caps.

ALWAYS, when possible, reduce the number or

transitions and turns. If long duct run is required,

increase duct size.

If turns or transitions are required; install as far

away from hood duct output and as far apart,

between the two as possible.

Minimum mount height between range top to hood

bottom should be no less than 24”.

Maximum mount height should be no higher than

32”.

It is important to install the hood at the proper

mounting height. Hoods mounted too low could

UHVXOWLQKHDWGDPDJHDQG¿UHKD]DUGZKLOHKRRGV

mounted too high will be hard to reach and will

ORVHLWVSHUIRUPDQFHDQGHI¿FLHQF\

If available, also refer range manufacturer’s height

clearance requirements and recommended hood

mounting height above range.

Vertical Ducting:

3-1/4”x10” minimum

Horizontal Ducting:

3-1/4”x10” minimum

DAMAGE-SHIPMENT / INSTALLATION:

 3OHDVHIXOO\LQVSHFWXQLWIRUGDPDJHEHIRUH

installation.

,IWKHXQLWLVGDPDJHGLQVKLSPHQWUHWXUQWKH

unit to the store in which it was bought for

repair or replacement.

 ,IWKHXQLWLVGDPDJHGE\WKHFXVWRPHUUHSDLU

or replacement is the responsibility of the

customer.

 ,IWKHXQLWLVGDPDJHGE\WKHLQVWDOOHULIRWKHU

WKDQWKHFXVWRPHUUHSDLURIUHSODFHPHQWPXVW

be made by arrangement between customer

and installer.

36”

24” min.

32” max.

7

WARNING FIRE HAZARD

NEVER exhaust air or terminate duct work into spaces between walls, crawl spaces, ceiling, attics or garages.

All exhaust must be ducted to the outside.

Use metal ductwork only.

)DVWHQDOOFRQQHFWLRQVZLWKVKHHWPHWDOVFUHZVDQGWDSHDOOMRLQWVZLWKFHUWL¿HG6LOYHU7DSHRU'XFW7DSH

Some Ducting Options

Installation – Ducting Options

Roof Pitch w/

Flashing & Cap

Rear Ducting

3-1/4”x10”

vertical ducting

3-1/4”x10”

horizontal ducting

Air Recirculating

8

www.zephyronline.com

Installation – 6SHFL¿FDWLRQV

35-15/16” (36”)

29-15/16” (30”)

23-15/16” (24”)

33-7/8” (36”)

27-7/8” (30”)

22-1/16” (24”)

33-5/8” (36”)

27-5/8” (30”)

21-5/8” (24”)

2-3/4”

C/L

8-5/8”

1-3/8”

9-1/16”

2”

12-3/16”

10-7/8”

3/4”

9-1/16”

elec.

k/o

elec.

k/o

5-1/2”

14-3/8”

19-5/16”

20-3/32”

TOP

BACK SIDE

1/2”

10”

3-1/4”

10”

3-1/4”

C/L

Air Recirculating Louver Plate

ELECTRICAL

WARNING

$OO(OHFWULFDOZRUNPXVWE\SHUIRUPHGE\TXDOL¿HGHOHFWULFLDQRUSHUVRQZLWKVLPLODUWHFKQLFDONQRZ

how and background.

For personal safety, remove house fuse or open circuit breaker before beginning installation. Do not use

extension cord or adapter plug with this appliance.

Follow national electrical codes or prevailing local codes and ordinances.

Electrical Supply:

This appliance requires a 120V 60Hz electrical supply, and connected to an individual, properly grounded

branch circuit, protected by a 15 or 20 ampere circuit breaker or time delay fuse. Wiring must be 2 wire w/

ground. Please also refer Electrical Diagram labeled on product.

AK11xxx - 152 Watts @ 1.3 Amps

AK12xxBx - 70 Watts @ 0.8 Amps

Cable Lock:

$FDEOHORFNLQJFRQQHFWRUQRWVXSSOLHGPLJKWDOVREHUHTXLUHGE\ORFDOFRGHV&KHFNZLWKORFDOUHTXLUHPHQWV

and codes, purchase and install appropriate connector if necessary.

Installation – Preparing Electrical

Cable Lock

9

1. Remove filters

2. Remove cover from junction box to

gain access to electrical wiring.

3. If using a cable lock, pry open the

desired electrical knockout either on

top or back of hood. Feed the wires

through the cable lock. Some local

codes require the use of a cable lock,

check your local codes.

4. If using hood in air recirculating

mode skip steps 4 and 5.

Pry open desired 3-1/4” x 10” ducting

knock-out either on top or back of

hood.

5. Secure 3-1/4” x 10” starting collar

with damper to the duct opening using

(10) M4x8 screws.

Installation – Preparing Electrical and Ducting

10

www.zephyronline.com

An air recirculating kit (optional) must be

purchased before using hood in recirculat-

ing mode.

1. Secure each of the (2) spring clips to the

safety grille body (A). Do this by inserting

the screw through the spring and into the

clip. Secure each clip to the safety grille

body by using a philips head screwdriver.

2. Insert charcoal filter into charcoal filter

holder (B) and place it over the safety grille

body (A)

3. Secure charcoal filter holder to safety

grill body by lifting up on spring clips and

twisting. The clip should cover the lip of the

charcoal filter holder securely.

4. Remove each screw from recirculating

top plate. Plate is located on top of hood

towards the front.

NOTE: Skip the recirculating preparation pages if you are ducting the air out of your home.

Recirculating preparation

continued on next page

Installation – Converting to Air Recirculating Mode

Recirculating kit - 0AK11-21001

5HSODFHPHQW¿OWHU$.

11

7KHIROORZLQJLQVWUXFWLRQVDUHIRU%UHH]H,,DQG%UHH]H,KRRGVEHJLQQLQJZLWKVHULDOQXPEHUSUH¿[DQGODWHU

Installation – Converting to Air Recirculating Mode

12

www.zephyronline.com

5. Remove each of the 5 screws holding

the (2) interior recirculating panels.

6. Remove (2) interior recirculating panels.

7. Place louvered recirculating plate over

top opening and secure using the screws

previously removed.

NOTE: Skip this page if you are ducting the air out of your home.

Installation – Mounting the Range Hood

13

Hood is designed for installation under a kitchen

cabinet (Fig 1)

 6HOHFWSUHIHUUHGGXFWORFDWLRQYHUWLFDORUKRUL]RQWDOLI

ducting out of kitchen. Refer to page 7 for details.

 %HJLQLQVWDOODWLRQE\UHPRYLQJWKH¿OWHUVLILQVWDOOHG

DQGVLGHVSDFHUSDQHOV´PRGHOVRQO\)LJ

3. Reinforce cabinet with 1”x2” wood strips if additional

strengthening is required or if cabinets are framed.

4. Temporarily position the range hood in the desired

mounting location. Measure and mark the mounting

holes, duct and electrical locations with a pencil.

5. Drill/cut out the required openings for duct and

electrical access by following the dimensions on page

8; make sure the duct opening is large enough to apply

duct tape.

 )DVWHQKRRGRQWRFDELQHWZLWK0ZRRGVFUHZV

with washers provided.

7. Install electrical.

8. Install duct work and seal with duct tape.

 5HLQVWDOO¿OWHUVDQGVLGHVSDFHUSDQHOVLIDSSOLFDEOH

10. Power up hood and check for leaks around duct tape.

11. If recirculating the hood refer to page 11 and 12 for

details.

duct/silver

tape

Duct

opening

cutout

Add 1x2

wood strips

electrical

Fig 1

6KRZQDVYHUWLFDOGXFWLQJ

Push in on panel latch then pull panel down

Fig 2

14

www.zephyronline.com

Features & Controls – Controls & Features

This switch turns the blower on and o and controls the speed selection.

is o, is low speed, is medium speed and is high speed.

is o, is dim, II is bright.

Breeze I, AK11xx

Lights Off/Dim/Bright

Blower On/Off/Speed Selection

This button turns the motors on and o. It also shuts o power to the whole hood.

If the lights are on and this button is pushed, they will also turn o.

This button turns the lights on, o and also dims them. Press once to turn them on bright,

again for dim and one more time to shut them o.

This button will change the speed setting of the motors. By pushing it you will change the

speeds from high to medium to low.

This button will put the hood into delay o mode. When pushed, the hood will switch to the

lowest speed and the entire hood will shut down all functions after 5 minutes.

Breeze II, AK12xxBx

15

SURFACE MAINTENANCE:

Do not use corrosive detergents, abrasive detergents or oven cleaners.

Do not use any product containing chlorine bleach or any product containing chloride.

Do not use steel wool or abrasive scrubbing pads which will scratch and damage surface.

Cleaning Stainless Steel

&OHDQSHULRGLFDOO\ZLWKZDUPVRDS\ZDWHUDQGFOHDQFRWWRQFORWKRUPLFUR¿EHUFORWK$OZD\VUXELQWKH

direction of the stainless steel grain. To remove heavier grease build up use a liquid degreaser detergent.

After cleaning use a non-abrasive stainless steel polish/cleaners, to polish and buff out the stainless luster and

JUDLQ$OZD\VVFUXEOLJKWO\ZLWKFOHDQFRWWRQFORWKRUPLFUR¿EHUFORWKDQGEXIILQWKHGLUHFWLRQRIWKHVWDLQOHVV

steel grain.

Cleaning Black Stainless Steel

&OHDQSHULRGLFDOO\ZLWKZDUPVRDS\ZDWHUDQGFOHDQFRWWRQJFORWKRUPLFUR¿EHUFORWK7RUHPRYHKHDYLHU

grease build up use a liquid degreaser detergent.

Due to a built-in layer of protective anti-smudge coating, do not use stainless steel polish/cleaners to buff out

black stainless steel.

Aluminum Mesh Filters

7KHDOXPLQXPPHVK¿OWHUVDUHLQWHQGHGWRWUDSUHVLGXHDQGJUHDVHIURPFRRNLQJ$OWKRXJKWKH¿OWHUVVKRXOG

never need replacing, they are required to be cleaned every 30 days or more often depending on cooking

habits.

)LOWHUVPD\EHSODFHGLQGLVKZDVKHUDWORZKHDWRUVRDNHGLQKRWVRDS\ZDWHU'U\¿OWHUVDQGUHLQVWDOOEHIRUH

using hood.

Removing Aluminum Mesh Filters (Fig 3)

 3XVKLQRQ¿OWHUKDQGOHV

 3LYRWIURQWRI¿OWHUGRZQZDUG

 5HPRYH¿OWHUE\SXOOLQJDZD\IURPKRRG

Replacing Aluminum Mesh Filters

Hood Model: Part No. Qty. to Order.

AK1124x 50200013 2

AK1100x / AK1136x 50200012 2

AK1200Bx / AK1236Bx 50200012 2

Maintenance – Cleaning and Filter Removal

Fig 3

16

www.zephyronline.com

BREEZE I, AK11xx model ONLY

REPLACING LIGHT BULBS

CAUTION: Light bulb becomes extremely hot when turned on.

DO NOT touch bulb until switched off and cooled. Touching hot bulbs could cause serious burns.

Make sure all power is turned off and bulbs are not hot.

Remove by turning bulb counter clockwise. Note: Bulb does not unscrew; it turns 60 degrees, stops and falls

out.

,IEXOEVDUHGLI¿FXOWWRWXUQGXHWRSURORQJHGXVH¿UPO\DWWDFKDJODVVVXFWLRQFXSDSSUR[LPDWHO\WKHGLDPHWHURI

the bulb or use a rubber/latex glove and turn counter clockwise.

Replacement bulbs are available at most hardware stores or from www.zephyronline.com

3XUFKDVHW\SH05*8:KDORJHQ

For Zephyr part numbers please turn to page 19 of the manual.

Maintenance – Lights

Bottom hood view

Troubleshooting

17

TROUBLESHOOTING PROCEDURES FOR BREEZE I AND BREEZE II

Issue Cause What to do

After installation,

the unit doesn’t

work.

1. The power source is not turned ON. 1. Make sure the circuit breaker and the unit’s

power is ON.

2. The power line and the cable locking connector

is not connecting properly.

2. Check the power connection with the unit is

connected properly.

3. The switch or control board wirings are

disconnected.

3. Make sure the wirings at the switch or control

board are connected properly.

4. The wires on control board or switch are loose. 4. Make sure the wires on the control board or

switch are connected properly.

5. The switch or control board is defective. 5. Change the switch or control board.

Light works, but

blower is not

turning.

1. The blower is defective, possible seized. 1. Change the blower.

2. The thermally protected system detects if the

blower is too hot to operate and shuts the blower

down.

2. The blower will function properly after the

thermally protected system cool down.

3. Damaged capacitor. 3. Change the capacitor.

4. The control board or blower switch is defective. 4. Change the control board or blower switch.

The unit is

vibrating.

1. The blower is not secure in place. 1. Tighten the blower in place.

2. Damaged blower wheel. 2. Change the blower wheel.

3. The hood is not secured in place. 3. Check the installation of the hood.

The unit is

whistling.

7KH¿OWHULVQRWLQWKHFRUUHFWSRVLWLRQ $GMXVWWKH¿OWHUVXQWLOWKHZKLVWOLQJVWRSV

2. The duct pipe connections are not sealed or

connected properly.

2. Check the duct pipe connections to be sure all

connections are sealed properly.

The blower is

working, but the

lights are not.

1. Defective bulb. 1. Change the bulb.

2. The light bulb is loose. 2. Tighten the light bulb.

3. The light bulb plug is disconnected. 3. Connect the light bulb plug.

The hood is

not venting out

properly.

1. The hood might be hanging to high from the

cook top.

1. Adjust the distance between the cook top and

the bottom of the hood within 24” and 32”

range.

2. The wind from the opened windows or opened

doors in the surrounding area are affecting the

ventilation of the hood.

2. Close all the windows and doors to eliminate

WKHRXWVLGHZLQGÀRZ

3. Blockage in the duct opening or duct work. 3. Remove all the blocking from the duct work or

duct opening.

4. The direction of duct opening is against the wind. 4. Adjust the duct opening direction.

5. Using the wrong size of ducting. 5. Change the ducting to correct size.

Mesh Filter is

vibrating.

0HVK¿OWHULVORRVH 1. Make sure the metal clips in the handle are

QRWVWXFN2UUHSODFHWKHPHVK¿OWHU

2. Filter sping clip is broken. 8QLQVWDOODQGUHLQVWDOO¿OWHUSXVKXSRQ¿OWHU

ODWFK5HSODFHPHVK¿OWHULIQHHGHG

18

www.zephyronline.com

Wiring Diagrams

RED

BLACK

THERMALLY PROTECTED

Fan: 65W

Lamp: 5W

Total: 70W @0.8A

Power consumption

Voltage:

Models :

AK1236Bx

120V 60Hz

AK1200Bx,

La page charge ...

Zephyr AK1200BB Hood User Manual

Ce manuel convient également à

Zephyr AK1200BB Hood User Manual

dans d''autres langues

Documents connexes