Wolf Cooktop ICBCT30EU Manuel utilisateur

Marque: Wolf

Modèle: Cooktop ICBCT30EU

Catégorie: Plaques électriques

Taper: Manuel utilisateur

ELECTRIC COOKTOPS

USE & CARE INFORMATION

GUÍA DE USO Y MANTENIMIENTO

GUIDE D’UTILISATION ET D’ENTRETIEN

INFORMAZIONI SU USO E MANUTENZIONE

BEDIENUNGS- UND PFLEGEANLEITUNG

ENGLISH

Introducing Wolf Electric Cooktops 5

Safety Instructions & Precautions 6

Wolf Electric Cooktop Features 8

Wolf Electric Cooktop Use & Care 13

Wolf Troubleshooting Guide 20

Wolf Service Information 21

ESPÃNOL

Presentación de las placas

vitrocerámicas de Wolf 23

Precauciones e instrucciones de seguridad 24

Características de las vitrocerámicas

de Wolf 26

Uso y mantenimiento de las

vitrocerámicas de Wolf 31

Guía de localización y solución

de problemas de Wolf 38

Información de mantenimiento de Wolf 39

FRANÇAIS

Présentation des plaques de cuisson

électriques Wolf 41

Instructions et mesures de sécurité 42

Caractéristiques des plaques de cuisson

électriques Wolf 44

Utilisation et entretien de la plaque

de cuisson électrique Wolf 49

Guide de dépistage des pannes Wolf 56

Service après-vente Wolf 57

ITALIANO

Piani di cottura elettrici Wolf 59

Precauzioni e istruzioni di sicurezza 60

Funzioni dei piani cottura elettrici Wolf 62

Uso e manutenzione dei piani

di cottura elettrici Wolf 67

Guida alla soluzione dei problemi Wolf 74

Informazioni sull’assistenza Wolf 75

DEUTSCH

Einführung der Elektrokochfelder von Wolf 77

Sicherheitshinweise u. Vorsichtsmaßnahmen 78

Leistungsmerkmale der Elektrokochfelder

von Wolf 80

Bedienung und Pflege von

Elektrokochfeldern von Wolf 85

Anleitung zur Fehlersuche von Wolf 92

Serviceinformationen von Wolf 93

As you read this Use & Care Information,

take particular note of the CAUTION and

WARNING symbols when they appear.

This information is impor tant for safe and

efficient use of the Wolf equipment.

In addition, this Use & Care Information may

signal an IMPORTANT NOTE which highlights

information that is especially important.

signals a situation where minor injury or

product damage may occur if you do not

follow instructions.

states a hazard that may cause serious

injury or death if precautions are not

followed.

WOLF

is a registered trademark of Wolf Appliance, Inc.

THANK YOU

Your purchase of a Wolf electric cooktop

attests to the importance you place upon the

quality and performance of your cooking

equipment. We understand this importance

and have designed and built your cooktop

with quality materials and workmanship to

give you years of dependable service.

We know you are eager to start cooking, but

before you do, please take some time to read

this Use & Care Information. Whether you are

a beginning cook or an expert chef, it will be

to your benefit to familiarize yourself with the

safety practices, features, operation and care

recommendations of the Wolf electric

cooktop.

We appreciate your choice of a Wolf

Appliance product and welcome any sugges-

tions or comments you may have. Please visit

our website at www.wolfappliance.com.

WOLF

ELECTRIC COOKTOPS

CONTACT

INFORMATION

Website:

wolfappliance.com

WHAT TO DO

IMPORTANT NOTE: Read all

instructions before using this

appliance.

Read this Use & Care Information

carefully before using your new

cooktop to reduce the risk of fire,

electric shock or injury to persons.

Ensure proper installation and

servicing. This appliance must be

properly installed and grounded by

a qualified technician. Have the

installer show you where the fuse

box is located so that you know

where to turn off power.

Wear proper apparel. Never let loose

clothing or other flammable

materials come in contact with the

elements while in operation. Fabric

may ignite and result in personal

injury.

SAFETY INSTRUCTIONS AND PRECAUTIONS

Use only dry pot holders when

removing pans from the cooktop.

Wet or damp pot holders on hot

surfaces may result in burns from

steam. Do not let pot holders touch

hot heating elements.

Select cookware of the proper size,

material and construction for the

particular type of cooking being

done. This unit is equipped with one

or more surface units of different

size.

Always turn pan handles inward so

they do not extend over adjacent

work areas, heating elements or

edges of cooktop to reduce the risk

of burns, ignition of flammable

materials and spillage due to

unintentional contact with pan. Do

not turn handles toward the room,

where they may be bumped or

easily hit.

Always use a setting of eight bars

or less on the bridge element when

cooking on a griddle. Higher settings

after a preheat of 5 minutes on

14 bars can damage the cooktop and

cookware. Refer to Bridge-Zone

Element on page 16.

WHAT NOT TO DO

Never use your cooktop to warm or

heat a room.

When using the cooktop DO NOT

TOUCH THE GLASS SURFACE

directly above or adjacent to the

heating elements. The glass surface

may become hot enough to cause

burns.

Do not leave children alone or

unattended in the area where the

cooktop is in use. Never allow

children to sit or stand on the

appliance. Do not let children play

with the cooktop.

Do not repair or replace any part of

the appliance unless it is specifically

recommended in literature you

received. All service should be

referred to a Wolf authorized service

center.

Do not use water on grease fires.

Smother the flame or use a dry

chemical or foam-type extinguisher.

Never leave the cooktop unattended

when using high heat settings.

Boilovers and greasy spillovers may

smoke or ignite.

If the surface is cracked, switch

off the appliance to avoid the

possibility of electric shock. Call a

Wolf authorized service center to

repair the appliance.

Do not store flammable materials

near hot components or let grease

or other flammable substances

accumulate on the cooktop.

Do not use a steam cleaner or clean

the cooktop while it is still hot. If

using a damp sponge or cloth, wait

until the cooktop has cooled

sufficiently to prevent steam burns.

Also, some cleaners give off noxious

fumes when applied to hot surfaces.

Refer to Cooktop Cleaning on page

18 and Cooktop Care on page 19.

Do not use a griddle, open roaster

or fish poacher across two heating

elements unless the bridge element

is turned on. This type of use

without the bridge element turned

on could damage or crack the glass.

Refer to Bridge-Zone Element on

page 16.

Do not block the cooling fan

exhaust or intake vents. The cooling

fan automatically turns on to cool

internal parts. It may continue to run

even after the cooktop has been

turned off.

DO NOT store items of interest to

children above or at the back of

the cooktop, as they could climb

on the appliance to reach items

and be injured.

FRAMED ELECTRIC COOKTOPS

Classic stainless steel trim

Easy-to-clean black ceramic glass surface is

resistant to scratching, staining, impact and

heat—translucent surface allows you to see

the glow of hot elements

High-frequency pulsation elements improve

cooking performance and control

Temperature limiter to ensure that safe

operating temperature of ceramic glass is

never exceeded

Illuminated touch controls with graduated

control lighting

True Simmer setting on all elements

Melt setting on one element

Hot-surface indicator light in control

panel

WOLF ELECTRIC COOKTOP FEATURES

Model ICBCT15E

Model ICBCT30E

Model ICBCT36E

These appliances are certified by Star-K

to meet strict religious regulations in

conjunction with specific instructions

found on www.star-k.org.

Lock mode—cooktop can be locked so that

no elements can be turned on

Universal OFF turns all elements off

Countdown timer with 1 to 99 minute range

and adjustable sound frequency and

volume

CE certified

MODEL ICBCT15E

381 mm Framed Electric Cooktop

Electronic

touch controls

Triple-zone

element

Location of

rating plate

Lock key

Hot-surface

indicator light

Classic stainless

steel trim finish

Universal OFF

key

Countdown

timer

True Simmer

Melt setting

FRAMED ELECTRIC COOKTOPS

381 mm FRAMED COOKTOP

Two heating elements with four zones

Triple-zone element power:

900 W/1800 W/2500 W (maximum)

Single element power: 1200 W (maximum)

Electric rating: 3.7 kW

762 mm FRAMED COOKTOP

Three heating elements with seven zones

Triple-zone element power:

900 W/1800 W/2500 W (maximum)

Single element power: 1200 W (maximum)

Bridge-zone element power—(2) 1800 W

single elements with 800 W bridge: 4400 W

(maximum)

Electric rating: 8.1 kW

WOLF ELECTRIC COOKTOP FEATURES

MODEL ICBCT30E

762 mm Framed Electric Cooktop

Triple-zone

element

Location of

rating plate

Stainless steel

trim finish

Bridge-zone

element

Electronic touch

controls

Lock key

Hot-surface

indicator light

Universal OFF

key

Countdown

timer

Melt setting

True Simmer on

all elements

FRAMED ELECTRIC COOKTOPS

914 mm FRAMED COOKTOP

Four heating elements with nine zones

Triple-zone element power:

1050 W/2200 W/2700 W (maximum)

Dual-zone element power:

700 W/2200 W (maximum)

Single element power: 1200 W (maximum)

Bridge-zone element power—(2) 1800 W

single elements with 800 W bridge: 4400 W

(maximum)

Electric rating: 10.5 kW

WOLF ELECTRIC COOKTOP FEATURES

MODEL ICBCT36E

914 mm Framed Electric Cooktop

Electronic touch

controls

Bridge-zone

element

Stainless steel

trim finish

Hot-surface

indicator light

Universal OFF

key

Triple-zone

element

Dual-zone

element

These appliances are certified by Star-K

to meet strict religious regulations in

conjunction with specific instructions

found on www.star-k.org.

Countdown

timer

Location of

rating plate

Lock key

Melt setting

True Simmer on

all elements

WOLF ELECTRIC COOKTOP FEATURES

Model ICBCT30EU

Model ICBCT36EU

UNFRAMED ELECTRIC COOKTOPS

Can be mounted flush with top of counter-

top or as a frameless installation sitting on

top of the countertop surface

Easy-to-clean black ceramic glass surface is

resistant to scratching, staining, impact and

heat—translucent surface allows you to see

the glow of hot elements

High-frequency pulsation elements improve

cooking performance and control

Temperature limiter to ensure that safe

operating temperature of ceramic glass is

never exceeded

Illuminated touch controls with graduated

control lighting

True Simmer setting on all elements

Melt setting on one element

Hot-surface indicator light in control

panel

Lock mode—cooktop can be locked so that

no elements can be turned on

Universal OFF turns all elements off

Countdown timer with 1 to 99 minute range

and adjustable sound frequency and

volume

CE certified

MODEL ICBCT30EU

762 mm Unframed Electric Cooktop

These appliances are certified by Star-K

to meet strict religious regulations in

conjunction with specific instructions

found on www.star-k.org.

Triple-zone

element

Location of

rating plate

Unframed edge

Bridge-zone

element

Electronic touch

controls

Hot-surface

indicator light

Universal OFF

key

Countdown

timer

Lock key

Melt setting

True Simmer on

all elements

WOLF ELECTRIC COOKTOP FEATURES

914 mm UNFRAMED COOKTOP

Four heating elements with nine zones

Triple-zone element power:

1050 W/2200 W/2700 W (maximum)

Dual-zone element power:

700 W/2200 W (maximum)

Single element power: 1200 W (maximum)

Bridge-zone element power—(2) 1800 W

single elements with 800 W bridge: 4400 W

(maximum)

Electric rating: 10.5 kW

UNFRAMED ELECTRIC COOKTOPS

762 mm UNFRAMED COOKTOP

Three heating elements with seven zones

Triple-zone element power:

900 W/1800 W/2500 W (maximum)

Single element power: 1200 W (maximum)

Bridge-zone element power—(2) 1800 W

single elements with 800 W bridge: 4400 W

(maximum)

Electric rating: 8.1 kW

MODEL ICBCT36EU

914 mm Unframed Electric Cooktop

Electronic touch

controls

Bridge-zone

element

Location of

rating plate

Unframed edge

Hot-surface

indicator light

Universal OFF

key

Triple-zone

element

Dual-zone

element

Countdown

timer

Lock key

Melt setting

True Simmer on

all elements

WOLF ELECTRIC COOKTOP USE & CARE

Touch control panel Lock mode key touch pad

CONTROL OPERATION

The Wolf electric cooktop operates by using

high-frequency pulsation, cycling the heating

elements between zero power and full power.

As the heat is increased on the control panel,

the element will stay at full power for longer

periods and have shorter periods of zero

power.

When using the dual-zone or triple-zone

elements, all sections of the element will cycle

at the same rate. For safety reasons, the outer

elements cannot be turned on independently

from the center section.

TOUCH

CONTROL PANEL

The control panel of your electric cooktop is

illuminated for instant visual indication that

one or more elements are in use. The control

panel features touch controls with graduated

control lighting. The illustrations below show

the control panel of Model ICBCT36E.

MODES OF OPERATION

LOCK MODE

Lock mode

, all touch pad operations on

the control panel are disabled and all heating

elements are turned off. A steady glowing light

within the symbol indicates that the

unit is locked. Refer to the illustration below.

To lock the control panel,

touch and hold

for 3 seconds. The unit will beep

three times and the light within the

symbol will illuminate. The control unit is

now in

Lock mode

To unlock the control panel,

touch and

hold for 3 seconds. The unit will

beep twice and the light within the

symbol will go out. The control unit is now

Idle mode

IMPORTANT NOTE:

When the unit is powered

up for the first time or if there has been a

power outage for longer than 5 seconds, the

cooktop will default to

Lock mode

IDLE MODE

After unlocking the control panel as described

in Lock Mode, the unit enters the

Idle mode

operation. The only valid touch pad operations

are for each element, the and

the timer functions.

Lock key

touch pad

WOLF ELECTRIC COOKTOP USE & CARE

INITIAL

START-UP

Before operating the cooktop for the first time,

please read the entire Use & Care Information.

Clean the cooktop surface as outlined in the

Ceramic Glass Top cleaning section on page

18. The cooktop surface must be free of any

foreign substances, especially those that could

melt and permanently adhere to the glass.

During the first uses of your new electric

cooktop, you may smell a slight burning odor

or see light smoke. Both of these conditions

are normal in new ceramic glass cooktops.

HOT-SURFACE INDICATOR

As a safety precaution, a hot-surface indicator

light will illuminate when the surface

temperature of any one of the heating

elements rises above 65˚C. will illuminate

in the control panel. It will remain illuminated

until the entire surface temperature has

decreased to a safe level. Even if the cooktop

controls are turned off, you are alerted that an

area of the cooktop remains hot.

COOLING FAN

The electric cooktop is equipped with a cooling

fan that automatically turns on to cool internal

parts. The fan will turn off once internal

temperatures have been lowered. During

extended use, the cooling fan may continue to

run even after the cooktop has been turned off

until internal temperatures have been lowered.

Make sure that the cooktop surface is

clean and dry before operating.

Do not place hot cooking utensils directly

over the control panel.

Hot-surface

indicator light

Hot-surface indicator light

WOLF ELECTRIC COOKTOP USE & CARE

COOKTOP OPERATION

SINGLE ELEMENT AND INNER ZONE

To turn on a heating element,

touch the

touch pad that corresponds to the

element you wish to use. The power bar

indicator graph will begin to blink and show

a half-power status.

Touch one of the following symbols or touch

pads of the element control while the power

bar indicator graph is still blinking:

Touch to set the element at the

highest heat setting.

Touch the ”

” or ”

–

” symbol to set the heat

setting at half-power output.

Touch or to set the element at

the lowest heat setting.

To change the heat setting:

Touch the ”

” or ”

–

” symbol to change the

heat setting incrementally up or down.

Touch to set the element at the

highest heat setting.

Touch or to set the element at

the lowest heat setting.

Touch to turn the element off.

IMPORTANT NOTE:

To quickly turn off all

heating elements, use the universal

touch pad located in the lower right area of the

control panel. Refer to the illustration below.

DUAL-ZONE ELEMENT

To turn on a dual-zone heating element,

touch the touch pad of the control that

corresponds with the dual-zone element. Refer

to the illustration on the following page.

Set the heat setting for the inner element

zone as described previously.

Touch and the outer element zone

will be set to the same heat setting as the

inner zone. A light will remain on under the

touch pad to indicate the outer

element zone has been turned on.

Changing the heat setting to the entire

dual-zone element is the same as for a

single element.

Touch again to turn off the outer

element zone. The light under the

touch pad will go out.

The illustrations below show the control panel

of Model ICBCT36E.

Heat settingsHeating element activation Universal OFF touch pad

Universal OFF

touch pad

SIM touch

pad

HIGH

touch pad

OFF ON

touch pad

”+” and ”–”

symbols

WOLF ELECTRIC COOKTOP USE & CARE

BRIDGE-ZONE ELEMENT

When activated, the bridge-zone element

creates an oblong heating area for use with a

griddle, open roaster or fish poacher.

To turn on the bridge-zone heating element,

touch the touch pad of either control

that corresponds with the bridge zone element.

Refer to illustration below.

Set the heat setting for either the front or

rear element as described on page 15.

Touch . The bridge element and the

element that is not turned on will both be

set to the same heat setting as the first

element. Lights will remain on under the

front, rear and bridge element touch pads

to indicate the bridge-zone elements are on.

Changing the heat setting of the entire

bridge-zone element is done the same as

for a single element. All three elements

maintain the same heat setting.

Touch again to turn off the bridge

element. The light under the bridge element

touch pad will go out. The front and rear

elements will remain at the current heat

setting and will become independent of one

another.

The illustrations below show the control panel

of Model ICBCT36E.

COOKTOP OPERATION

TRIPLE-ZONE ELEMENT

To turn on a triple-zone heating element,

touch the touch pad of the control that

corresponds with the triple-zone element.

Refer to the illustration below.

Set the heat setting for the inner element

zone as described on page 15.

Touch and the middle element

zone will be turned on to the same heat

setting as the inner zone. A light will remain

on under the touch pad to indicate

the middle element zone is on.

Touch and the outer element

zone will be turned on to the same heat

setting as the inner and middle element

zones.

A light will remain on under the

touch pad to indicate the outer element

zone is on.

Changing the heat setting to the entire

triple-zone element is the same as for a

single element.

If is turned on directly, will

automatically be turned on. Similarly, if all

three zones are turned on, turning off

will automatically turn off .

When is turned on, lights under the

other two zones will dim. This is normal.

Triple-zone elementDual-zone element

Triple-zone

element control

Dual-zone

element control

Bridge-zone element

Bridge-zone

element control

WOLF ELECTRIC COOKTOP USE & CARE

TIMER OPERATION

The electric cooktop features a countdown

timer located in the control panel. Refer to the

illustration below.

The timer may be set to any one-minute

increment from 1 to 99. Once set, the

remaining time will be illuminated in the

control panel as it counts down. The timer is

available for use in any mode except

Lock

mode

To turn on the timer,

touch ”

” on the

timer control.

Touch and hold ”

” or ”

–

” until the desired

time is reached. The timer will start 3

seconds after the last change in value.

When the timer reaches 0, the unit will

sound. The reminder will continue to sound

until is pressed.

The illustration below shows the control panel

of Model ICBCT36E.

COOKTOP OPERATION

BRIDGE-ZONE ELEMENT GRIDDLE USE

Always use a setting of 8 bars or less on the

bridge-zone element when cooking on a

griddle. Higher settings are not needed and

can damage the cooktop and cookware.

To preheat the griddle,

set the bridge

element at 14 bars for 5 minutes, then turn the

heat down to 8 bars for cooking.

A griddle, open roaster, or fish poacher

should not be used when the bridge-zone

is off or on any of the other combination

of circular heating elements.

Countdown timer

Timer display

area

WOLF ELECTRIC COOKTOP USE & CARE

SOUND CONTROL

The electric cooktop is equipped with the

ability to change the volume and frequency, or

tone, of the touch controls through the user

option, activated through the timer controls.

To turn on user option,

the cooktop must

be in

Idle mode

Touch and hold for 3 seconds to

turn on the volume adjustment option. The

three-digit display will show ”Uol.”

Touch and hold for more than 5

seconds to turn on the frequency adjust-

ment option. The three-digit display will

show ”FRE.”

Both the volume and frequency are adjusted

using the ”

” and ”

–

” touch pads. One touch

equals one step up or down in volume or

frequency. The triple-zone element power bar

indicator graph will show the current status of

the volume or frequency and will change with

the user’s input. (1 bar = low, 8 bars = medium

and 16 bars = high.)

As the volume/frequency is adjusted, the

cooktop will beep with each change. The beep

will represent the volume/frequency level that

is currently displayed by the power bar graph.

To exit the user option and return the

cooktop to

Idle mode,

touch and hold

for more than 7 seconds.

Or, if no touch pad is touched for 10

seconds, the level is then stored and the

cooktop returns to

Idle mode

COOKTOP CLEANING

CERAMIC GLASS TOP

Lock the cooktop before cleaning by touching

and holding the symbol for 3 seconds.

Clean the top surface thoroughly before

operating the cooktop for the first time. Apply

approximately 5 ml of nonabrasive cleaner to

the surface of the ceramic glass with a lightly

dampened clean cloth. Use a second clean

cloth to remove any remaining cleaner residue.

Wipe the cooktop surface with a dry cloth to

completely eliminate any remaining moisture.

The cooktop should be cleaned after each use.

To avoid personal injury, be careful not to wipe

or clean any hot areas. It will be safe to clean

each element area whenever the hot-surface

indicator light has gone out.

To remove heavy or burned-on spills, allow the

cooktop to cool. Use the razor blade scraper

provided with the cooktop to scrape off any

burned-on substances. Remove any remaining

residue using the cleaning method described

above.

COOKTOP FRAME (FRAMED MODELS)

For general cleaning after each use, apply a

nonabrasive cleaner to the stainless steel

cooktop frame and gently wipe with a clean

towel or cloth. Be sure to remove any cleaner

residue from the frame and ceramic glass

surface before using the cooktop.

Pitting of the ceramic glass is possible if

spills with a high sugar content are left in

the hot zone. Use the razor blade

provided to move the spill to a cool area

for cleaning after the cooktop cools.

WOLF ELECTRIC COOKTOP USE & CARE

COOKTOP CARE

CERAMIC GLASS TOP CARE

Do not

use the cooktop as a cutting board.

Do not

slide rough-bottom cookware, such

as cast iron, across the glass surface.

Remove any resulting marks immediately

using the razor blade scraper and cleaning

cream as mentioned in Cooktop Cleaning

on page 18.

Do not

allow any item that could melt to

come in contact with the hot ceramic glass

surface. If such a condition occurs, remove

it immediately from the hot element with a

razor blade.

Do not

place food directly on cooktop

surface when it is warm or hot.

Do not

operate the cooktop if the ceramic

glass surface is broken. Contact a Wolf

authorized service center.

Do not

place a trivet, wok support ring or

other metal stand directly onto the cooktop

surface.

Do not

apply chlorine bleach, ammonia or

other strong chemicals or cleaners to the

cooktop surface.

Do not

use abrasive cleaners or applicators.

Do not

wipe the cooktop surface with a

sponge or dish cloth that may leave a film

of detergent; it will cause the cooktop to

discolor during the next heating cycle.

MAINTENANCE

The electric cooktop is a sealed system that

does not require internal maintenance. The

cleaning and care information outlines the

necessary maintenance for the ceramic glass

surface. A Wolf authorized service center must

perform all other maintenance.

Follow these guidelines to avoid injury

and prevent permanent damage to the

cooktop.

Do not set hot cooking utensils near the

sealed outer edges of flush-mounted

Models ICBCT30EU or ICBCT36EU. This

will cause damage to the silicone seal.

WOLF TROUBLESHOOTING GUIDE

TROUBLESHOOTING GUIDE

PROBLEM PROBABLE CAUSE CORRECTION

Cooktop does not

Cooktop is in Lock mode. Touch and hold the

function at all

symbol for 3 seconds to unlock

the control panel.

Cooktop is in Lock mode Errors may be cleared by

and the timer display shows pressing the button.

an error code.

No electricity is being Have an electrician check the

supplied to the cooktop. house power supply.

Fuse is blown or circuit Have an electrician replace the

breaker is tripped. fuse or reset the circuit breaker.

Cooktop is not connected to Have an electrician verify that

a proper electrical circuit. the proper voltage is being

applied to the cooktop.

Heating elements do not

Power supply connection Have an electrician tighten

heat properly

is loose. connections at the electrical

box.

Cooktop is not connected to Have an electrician verify that

a proper electrical circuit. the proper voltage is being

applied to the cooktop.

Heating elements cycle

Heating element temperature This is a normal function of the

off when unit is set for

limiters are temporarily cooktop. The elements will turn

full power

shutting off element due to on when the temperatures have

temperatures approaching cooled sufficiently.

the maximum allowable limit

of the ceramic glass.

La page charge ...

Wolf Cooktop ICBCT30EU Manuel utilisateur

Marque: Wolf

Modèle: Cooktop ICBCT30EU

Catégorie: Plaques électriques

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

italiano: Wolf Cooktop ICBCT30EU Manuale utente
español: Wolf Cooktop ICBCT30EU Manual de usuario
Deutsch: Wolf Cooktop ICBCT30EU Benutzerhandbuch

Wolf Cooktop ICBCT30EU Manuel utilisateur

Wolf Cooktop ICBCT30EU Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents