KitchenAid Washer/Dryer Front-Loading Automatic Dishwasher Manuel utilisateur
- Catégorie
- Machines à laver
- Taper
- Manuel utilisateur
Ce manuel convient également à
PRO LINE
™
FRONT-LOADING
AUTOMATIC WASHER
Use&CareGuide
For questions about features, operation/performance, parts, accessories or service, call: 1-800-422-1230
In Canada, for assistance, installation or service, call: 1-800-807-6777 or visit our website at...
www.kitchenaid.com or www.KitchenAid.ca
LAVEUSE AUTOMATIQUE PROLINE
™
À
CHARGEMENT FRONTAL
Guided’utilisationetd’entretien
Au Canada, pour assistance, installation ou service, composez le 1-800-807-6777 ou visitez notre site web à...
www.KitchenAid.ca
Table of Contents/Table des matières.............................................................................2
2
TABLE OFCONTENTS
WASHER SAFETY ..........................................................................3
INSTALLATION REQUIREMENTS................................................4
Tools and Parts ............................................................................4
Options.........................................................................................4
Location Requirements................................................................4
Drain System................................................................................6
Electrical Requirements...............................................................6
INSTALLATION INSTRUCTIONS..................................................7
Remove Decorative Mat ..............................................................7
Attach Door Handle......................................................................7
Remove Transport System..........................................................7
Route the Drain Hose...................................................................7
Connect the Inlet Hoses...............................................................8
Secure the Drain Hose.................................................................8
Level the Washer..........................................................................9
Complete Installation ...................................................................9
FEATURES AND BENEFITS ........................................................10
WASHER USE...............................................................................11
Starting Your Washer.................................................................11
Using the Proper Detergent.......................................................11
Using the Dispenser...................................................................12
Pausing or Restarting.................................................................14
Changing Cycles, Options and Modifiers..................................14
Status Display ............................................................................14
Cycles.........................................................................................15
Normal Sounds ..........................................................................16
Options.......................................................................................16
Modifiers.....................................................................................17
Laundry Guide............................................................................18
LAUNDRY TIPS ............................................................................19
Loading ......................................................................................19
WASHER CARE ............................................................................20
Cleaning Your Washer ...............................................................20
Water Inlet Hoses.......................................................................21
Vacation, Storage, and Moving Care.........................................21
TROUBLESHOOTING ..................................................................22
Washer and Components..........................................................22
Washer Operation......................................................................23
Clothing Care .............................................................................24
ASSISTANCE OR SERVICE.........................................................25
In the U.S.A. ...............................................................................25
In Canada...................................................................................25
WARRANTY ..................................................................................26
TABLE DES MATIÈRES
SÉCURITÉ DE LA LAVEUSE........................................................28
EXIGENCES D'INSTALLATION...................................................29
Outillage et pièces......................................................................29
Options.......................................................................................29
Exigences d'emplacement.........................................................30
Système de vidange...................................................................31
Spécifications électriques..........................................................32
INSTRUCTIONS D'INSTALLATION.............................................32
Retrait du revêtement décoratif .................................................32
Fixation de la poignée de porte .................................................32
Élimination des accessoires de transport..................................33
Acheminement du tuyau de vidange.........................................33
Raccordement des tuyaux d'alimentation.................................33
Immobilisation du tuyau de vidange..........................................34
Réglage de l'aplomb de la laveuse............................................34
Achever l'installation ..................................................................35
CARACTÉRISTIQUES ET AVANTAGES .....................................36
UTILISATION DE LA LAVEUSE...................................................37
Mise en marche de la laveuse....................................................37
Utilisation du détergent approprié .............................................37
Utilisation du distributeur...........................................................38
Pause ou remise en marche.......................................................40
Changement des programmes, options et modificateurs.........40
Témoins de l'état d'avancement................................................40
Programmes...............................................................................41
Sons normaux............................................................................43
Options.......................................................................................43
Modificateurs..............................................................................44
Guide de lessivage.....................................................................45
CONSEILS DE LESSIVAGE..........................................................46
Chargement ...............................................................................46
ENTRETIEN DE LA LAVEUSE .....................................................47
Nettoyage de la laveuse.............................................................47
Tuyaux d'arrivée d'eau...............................................................48
Précautions à prendre avant les vacances,
un entreposage ou un déménagement......................................48
DÉPANNAGE.................................................................................50
La laveuse et ses composants...................................................50
Fonctionnement de la laveuse...................................................51
Soin des vêtements....................................................................53
ASSISTANCE OU SERVICE.........................................................54
Aux États-Unis............................................................................54
Au Canada..................................................................................54
GARANTIE.....................................................................................55
3
WASHER SAFETY
You can be killed or seriously injured if you don't immediately
You
can be killed or seriously injured if you don't
follow
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”
These words mean:
4
INSTALLATION REQUIREMENTS
ToolsandParts
Gather the required tools and parts before starting installation.
The parts supplied are in the washer drum.
Tools needed for connecting the water inlet hoses
Tools needed for installation
Parts supplied
Alternate Parts
Your installation may require additional parts. If you are interested
in purchasing one of the items listed here, call the toll-free
number on the cover or in the “Assistance or Service” section.
Options
A pedestal may be purchased separately for this washer. This
pedestal will add about 11" (27.9 cm) to the height of your
washer for a total vertical height of approximately 53" (134.6 cm).
Optional pedestal
To order, call the dealer from whom you purchased your washer
or refer to the “Assistance or Service” section of this manual. Ask
for Model Number LAV2701RSS.
LocationRequirements
Selecting the proper location for your washer improves
performance and minimizes noise and possible washer “walk.”
Your washer can be installed under a custom counter, in a
basement, laundry room, closet, or recessed area. See “Drain
System.”
IMPORTANT: Do not install or store the washer where it will be
exposed to the weather.
Companion appliance location requirements should also be
considered. Proper installation is your responsibility.
You will need
■ A water heater set to deliver 120°F (49°C) water to the
washer.
■ A grounded electrical outlet located within 6 ft (1.8 m) of
where the power cord is attached to the back of the washer.
See “Electrical Requirements.”
■ Hot and cold water faucets located within 5 ft (1.5 m) of the
hot and cold water fill valves, and water pressure of
20-100 psi (137.9-689.6 kPa).
■ A level floor with a maximum slope of 1" (2.5 cm) under entire
washer. Installing the washer on carpeting is not
recommended.
■ A sturdy floor to support the washer with a total weight
(washer, water and load) of 550 lbs (249 kg).
Do not operate your washer in temperatures below 32°F (0°C).
Some water can remain in the washer and can cause damage in
low temperatures. See “Washer Care” for winterizing information.
■ Pliers that open to
1⁹⁄₁₆" (3.95 cm)
■ Flashlight (optional)
■ Adjustable or open end
wrenches, 13 mm and
⁹⁄₁₆" (14 mm)
■ #3 Phillips screwdriver
■ Ruler or measuring tape
■ Wood block
■ Level
A. Door handle
B. Door handle washers (2)
C. Door handle screws (2)
D. Cable tie
E. Transport bolt hole plug (4)
F. Inlet hose (2)
If You Have You Will Need to Buy
Laundry tub or
standpipe taller
than 96" (2.4 m)
Sump pump system (if not already
available)
Overhead sewer Standard 20 gal. (76 L), 30" (76.2 cm) tall
drain tub or utility sink and sump pump
(available from local plumbing suppliers)
Floor drain Siphon break, Part Number 285834;
additional drain hose Part
Number 8318155; and connector kit, Part
Number 285835
Drain hose too
short
4 ft drain hose extension kit, Part
Number 285863
Water faucets
beyond reach of fill
hoses
2 longer water fill hoses:
6 ft (1.8 m) Part Number 76314,
10 ft (3.0 m) Part Number 350008
A
B
C
E
F
D
5
Installation spacing
The following spacing dimensions are recommended for this
washer. This washer has been tested for installation with spacing
of 0" (0 cm) clearance on the sides, front, rear, and top.
Recommended spacing should be considered for the following
reasons:
■ The location must be large enough to allow the washer door
to be fully opened.
■ Additional spacing should be considered for ease of
installation and servicing.
■ Additional clearances might be required for wall, door, and
floor moldings.
■ Additional spacing of 1" (2.5 cm) on all sides of the washer is
recommended to reduce noise transfer.
■ Companion appliance spacing should also be considered.
Washer Dimensions
Recommended installation spacing for custom
undercounter installation, washer only
■ The dimensions shown are for a washer without the optional
decorative mat placed on top.
Recommended installation spacing for recessed or
closet installation, with or without a pedestal
■ For closet installation with a door, minimum ventilation
openings in the top and bottom of the door are required.
Louvered doors with equivalent openings are acceptable.
*Required spacing
Recommended installation spacing for cabinet
installation, with or without a pedestal
■ For cabinet installation, with a door, the minimum ventilation
openings in the top are required.
*Required spacing
*Includes the door handle.
**Includes the feet extended 1" (2.5 cm).
The optional decorative mat (included)
will add approximately ¹⁄₂" (1.3 cm).
NOTE: Door is not reversible.
57"
(144.8 cm)
27"
(68.6 cm)
33" (83.8 cm)*
42"
(106.7 cm)**
1"
(2.5 cm
)
1"
(2.5 cm)
42" min.
(106.7 cm)
27"
(68.6 cm)
1" (2.5 cm
)
A. Recessed area
B. Side view - closet or confined area
C. Closet door with vents
A.Front view
B. Side view
C. Cabinet with vents
A
B
1"
(2.5 cm)
33"
(83.8 cm)
1"
(2.5 cm)
1"
(2.5 cm
)
27"
(68.6 cm)
4"
(10.2 cm)
C
3"
(7.6 cm)
3"
(7.6 cm)
48 in.
2
(310 cm
2
)*
24 in.
2
(155 cm
2
)*
7" (17,8 cm)
*
7" (17,8 cm)*
4"
(10,2 cm)
33"
(83,8 cm)
27"
(68,6 cm)
1"
(2,5 cm)
1"
(2,5 cm)
1"
(2,5 cm)
C
B
A
6
DrainSystem
The washer can be installed using the standpipe drain system
(floor or wall), the laundry tub drain system, or the floor drain
system. Select the drain hose installation method you need. See
“Tools and Parts.”
Standpipe drain system - wall or floor (views A & B)
The standpipe drain requires a minimum diameter standpipe of
2" (5 cm). The minimum carry-away capacity can be no less than
17 gal. (64 L) per minute.
The top of the standpipe must be at least 30" (76.2 cm) high and
no higher than 96" (2.4 m) from the bottom of the washer.
Laundry tub drain system (view C)
The laundry tub needs a minimum 20 gal. (76 L) capacity. The top
of the laundry tub must be at least 30" (76.2 cm) above the floor.
Floor drain system (view D)
The floor drain system requires a siphon break that may be
purchased separately. See “Tools and Parts.”
The siphon break must be a minimum of 28" (71 cm) from the
bottom of the washer. Additional hoses might be needed.
ElectricalRequirements
■ A 120 volt, 60 Hz., AC only, 15- or 20-amp, fused electrical
supply is required. Time-delay fuse or circuit breaker is
recommended. It is recommended that a separate circuit
serving only this appliance be provided.
■ This washer is equipped with a power supply cord having a
3 prong grounding plug.
■ To minimize possible shock hazard, the cord must be
plugged into a mating, 3 prong, grounding-type outlet,
grounded in accordance with local codes and ordinances. If a
mating outlet is not available, it is the personal responsibility
and obligation of the customer to have the properly grounded
outlet installed by a qualified electrician.
■ If codes permit and a separate ground wire is used, it is
recommended that a qualified electrician determine that the
ground path is adequate.
■ Do not ground to a gas pipe.
■ Check with a qualified electrician if you are not sure the
washer is properly grounded.
■ Do not have a fuse in the neutral or ground circuit.
7
INSTALLATION INSTRUCTIONS
RemoveDecorativeMat
Remove the optional decorative mat (included) from the top of
the washer and set aside.
AttachDoorHandle
Remove parts package from washer drum. Check that all parts
were included.
Attach Door Handle
1. Insert the 2 screws through the holes in the door.
2. Place the plastic washers onto the screws.
3. Attach the handle by hand tightening the screws, first the top
then the bottom.
4. Push the handle against the door. Using a Phillips
screwdriver, tighten the screws.
NOTE: Do not overtighten.
RemoveTransportSystem
IMPORTANT: Position the washer so that the rear of the washer
is within approximately 3 ft (90 cm) of its final location.
There are 4 bolts in the rear panel of the washer that support the
suspension system during transportation. These bolts also retain
the power cord inside the washer until the bolts are removed.
1. Using a 13 mm wrench, loosen each of the bolts.
2. Once the bolt is loose, move it to the center of the hole and
completely pull out the bolt, including the plastic spacer
covering the bolt. The power cord will be attached to all
4 bolts inside the washer.
3. Once all 4 bolts are removed, discard the bolts and spacers.
Then pull the power cord through the opening of the rear
panel and close the hole with the attached cap.
4. Close the bolt holes with the 4 transport bolt hole plugs.
NOTE: If the washer is to be transported at a later date, call your
local service center. To avoid suspension and structural damage,
your machine must be properly prepared (transport system
installed) for relocation, by a certified technician.
RoutetheDrainHose
Proper routing of the drain hose helps avoid floor damage due to
water leakage. Read and follow these instructions.
The drain hose is connected to your washer. Gently pull the
corrugated drain hose from the shipping clips.
To keep drain water from going back into the washer:
■ Do not straighten the drain hose, and do not force excess
drain hose into standpipe. Hose should be secure, but loose
enough to provide a gap for air.
■ Do not lay excess hose on the bottom of the laundry tub.
Floor drain
You may need additional parts. See Floor drain under “Tools and
Parts.”
WARNING
Excessive Weight Hazard
Use two or more people to move and install washer.
Failure to do so can result in back or other injury.
8
ConnecttheInletHoses
IMPORTANT: Verify that there are rubber washers installed in
both ends of both of the inlet hoses. If one or more of the
washers is missing, call the toll-free number on the cover or in the
“Assistance of Service” section.
Connect the inlet hoses to the water faucets
Make sure the washer drum is empty.
1. Attach the red inlet hose to the hot water faucet. Screw on
coupling by hand until it is seated on the washer.
2. Attach the blue inlet hose to the cold water faucet. Screw on
coupling by hand until it is seated on the washer.
3. Using pliers, tighten the couplings with an additional
two-thirds turn.
NOTE: Do not overtighten or use tape or sealants on the valve.
Damage to the valves can result.
Clear the water lines
■ Run water through both faucets and inlet hoses, into a
laundry tub, drainpipe or bucket, to get rid of particles in the
water lines that might clog the inlet valve screens.
■ Check the temperature of the water to make sure that the hot
water hose is connected to the hot water faucet and that the
cold water hose is connected to the cold water faucet.
Connect the inlet hoses to the washer
1. Attach the red water inlet hose to the washer’s hot (H) water
inlet valve. Screw on coupling by hand until it is seated on the
washer.
2. Attach the blue water inlet hose to the washer’s cold (C) water
faucet. Screw on coupling by hand until it is seated on the
washer.
3. Using pliers, tighten the couplings with an additional
two-thirds turn.
NOTE: Do not overtighten. Damage to the coupling can
result.
4. Turn on the water faucets completely and check for leaks.
NOTE: Replace original inlet hoses after 10 years of use to
reduce the risk of hose failure. Record hose installation or
replacement dates on the hoses for future reference.
Periodically inspect and replace hoses if bulges, kinks, cuts,
wear, or leaks are found.
Securethe DrainHose
1. Drape the power cord over the washer top.
2. Secure the drain hose to the laundry tub leg or standpipe with
the cable tie provided. See illustrations A and B.
If the washer faucets and the drain standpipe are recessed
(see illustration C), put the hooked end of the drain hose in
the standpipe. Tightly wrap the cable tie around the water
inlet hoses and the drain hose.
NOTES:
■ Do not force excess drain hose back into the rear of the
washer.
■ Do not force excess drain hose into the standpipe.
■ To avoid siphoning, do not seal the drain hose into the
standpipe.
A. Coupling B. Washer
AB
H. Hot water inlet C. Cold water inlet
H
C
AB C
9
LeveltheWasher
One foot has been installed at a different height on your new
washer. The other three feet were preset at the factory. Properly
leveling your washer will minimize excessive noise and vibration.
1. Using a ⁹⁄₁₆" (14 mm) open-end wrench, verify that the nuts on
the three preset feet are tightened against the cabinet.
2. Slide the washer to its final location.
3. Push on the upper front panel to be sure that the washer is on
the rear feet. Lower the right front foot until it contacts the
floor. By hand, firmly rotate the foot up to an additional
1¹⁄₂ turns.
4. Check the levelness of the washer by placing a level on the
top edge of the washer, first side to side, then front to back.
5. Rock washer gently front to back, side to side and diagonally
to make sure that all four feet are in firm contact with the floor.
6. After the washer is level, use a ⁹⁄₁₆" (14 mm) open-end wrench
to turn the nuts on the feet tightly against the washer cabinet.
IMPORTANT: All four feet must be tightened. If the nuts are
not tight against the washer cabinet, the washer may vibrate.
7. If the washer is not level, move the washer out slightly and
first prop the front with a wood block and adjust the feet as
necessary. Then prop the back and adjust feet as necessary.
Repeat this step until the washer is level.
CompleteInstallation
1. Check the electrical requirements. Be sure that you have the
correct electrical supply and the recommended grounding
method. See “Electrical Requirements.”
2. Check that all parts are now installed. If there is an extra part,
go back through the steps to see which step was skipped.
3. Check that you have all of your tools.
4. Remove any protective film or tape remaining on the washer.
5. Set the optional decorative mat in place on top of the washer.
NOTE: Make sure the top of the washer and the bottom of
the mat are clean.
6. Dispose of/recycle all packaging materials.
7. Check that the water faucets are on.
8. Check for leaks around faucets and inlet hoses.
9. Plug into a grounded 3 prong outlet.
10. Read “Washer Use.”
11. To test and to clean your washer, measure ¹⁄₂ the detergent
manufacturer’s recommended amount of HE High Efficiency
detergent for a medium-size load. Pour the detergent into the
detergent dispenser. Select NORMAL/CASUAL, and then
select START. Allow the washer to complete one whole cycle.
10
FEATURES AND BENEFITS
Electronic Controls
Flexible electronic controls are easy to use whether you are a
beginner or an expert.
Detergent Advantage System Dispenser
The four compartments in the dispenser allow loading of all
laundry additives before the washer is started. The additives will
be dispensed into the wash at the optimal time for high
performance cleaning. Aimed bleach release is included in the
detergent advantage system. The detergent is added at the
beginning of the cycle and the bleach is added after the enzymes
have had a chance to do their cleaning. The fabric softener is
dispensed in the rinse cycle. The Detergent Advantage System
Dispenser tray is easily removed for cleaning.
Auto Water Level
Adjusting to the size of the load, this feature allows the washer to
use the minimal amount of water needed to clean and rinse the
clothes. Because only the required amount of water is used, the
washer saves energy, too.
Larger Load Size
Since there is no agitator, you can wash larger, bulkier items such
as an average size sleeping bag. You are also able to wash more
clothes at one time, which means fewer loads.
Suspension System
To reduce washer “walk” and “off-balance” conditions, your new
washer combines:
■ 2 Springs to isolate vibration
■ 4 Shock absorbers at the washer base to minimize movement
Stainless Steel Drum
The Stainless Steel drum eliminates corrosion and enables higher
spin speeds for more water extraction, reducing drying time.
Adaptive Variable Speed Motor
The motor adapts to the load size and to the cycle selected to
give the optimum cleaning, rinsing, and spinning conditions. The
motor can handle slow speeds needed for wool and delicate
items, but it is powerful enough to handle a large clothes load.
High-Efficiency Wash System
Your new front-loading, high-efficiency washer saves time with
fewer, larger loads, conserves resources and lowers your water
and energy bills too.
Spin Speeds
This washer automatically selects the spin speed based on the
cycle selected. This factory setting can be changed, however.
This washer offers up to six different spin speed choices.
Thermal Optimizer
The heating system ensures that the wash water is heated to the
preset temperature for Heavy Duty, White/Cotton, Sanitary, and
the Soil Treat option. It also provides “stepped cleaning” when
using the Sanitary cycle or the Soil Treat option. “Stepped
cleaning” starts the wash cycle with warm water to remove stains
(such as blood or grass). The water continues heating in order to
remove stains such as dirty mechanical oil.
Add A Garment
When lighted, Rapid Wash, Normal/Casual, Heavy Duty, White/
Cotton, and Sanitary can be paused and the door unlocked so
you can add a garment that may have been forgotten when
loading the washer. The ADD A GARMENT status message is
displayed for up to the first 8 minutes of a cycle and then the
LOCKED message will be displayed.
Direct Detergent Injection
A concentrated detergent solution is sprayed onto the clothes at
the beginning of the cycle to ensure that the detergent comes
into contact with the clothes as quickly as possible, removing
stains from your clothes without pretreating.
Dynamic Off-Balance Detection
This washer uses two sensors to detect load size and the amount
of off-balance within the load. The suspension system and
controls are specially designed to redistribute the load
automatically.
11
WASHER USE
StartingYourWasher
WARNING: To reduce the risk of fire, electric shock, or injury to
persons, read the IMPORTANT SAFETY INSTRUCTIONS before
operating this appliance.
The following is a guide to using your washer. Please refer to
specific sections of this manual for more detailed information.
Do not store laundry products on the top surface of this washer.
Vibration is normal during operation.
UsingtheProperDetergent
Use only High Efficiency detergents. The package for this type of
detergent will be marked “HE” or “High Efficiency.” This wash
system, along with less water, will create too much sudsing with a
regular non-HE detergent. Using regular detergent will likely result
in washer errors, longer cycle times and reduced rinsing
performance. It may also result in component failures and
noticeable mold or mildew. HE detergents are made to produce
the right amount of suds for the best performance. Follow the
manufacturer's instructions to determine the amount of detergent
to use.
First Wash Cycle Without Laundry
Before washing clothes for the first time, if not completed during
the final installation step, choose the Normal/Casual cycle and
run it without clothes. Use only HE High Efficiency detergent. Use
¹⁄₂ the manufacturer’s recommended amount for a medium-sized
load. This initial cycle serves to ensure the interior is clean before
washing clothes.
Fire Hazard
Never place items in the washer that are dampened
with gasoline or other flammable fluids.
No washer can completely remove oil.
Do not dry anything that has ever had any type of oil on
it (including cooking oils).
Doing so can result in death,explosion,or fire.
WARNING
Use only HE High Efficiency detergent.
12
For All Wash Cycles
1. To load washer
Open the washer door by pulling on the handle. Sort laundry
according to color and type of fabric. Place a load of sorted
clothes in the washer. Do not overload washer. Overloading
can cause poor cleaning.
■ The washer can be fully loaded, but not tightly packed.
Washer door should close easily.
■ Mix large and small items. Avoid washing a single item.
Load evenly.
■ Wash small items, such as infant socks, in mesh garment
bags. It is recommended that more than one garment bag
be used, and that each garment bag be filled with equal
amounts of material.
■ When unloading garments, occasionally check under the
rubber rim at the front of the tub for small items.
2. Close the washer door by pushing it firmly until the lock
clicks. The washer door will remain locked during the wash
cycle.
NOTE: After any wash cycle is completed, the door must be
opened and then closed before a new cycle can begin. The
door can be opened only if PAUSE/CANCEL is selected while
ADD A GARMENT shows in the status display or if the cycle
has been canceled. See “To cancel a cycle” in “Changing,
Cycles, Options and Modifiers” section.
3. Open the Dispenser Drawer and add laundry products to the
detergent, bleach, or fabric softener compartments. Close
drawer slowly to avoid spills. See “Using the Dispenser.”
4. Turn on the washer by selecting one of the WASH CYCLES.
The indicator light for the selected cycle will illuminate. When
selecting a Wash Cycle, the preset options, Soil Level, Temp,
Spin Speed for the selected cycle will illuminate. The display
shows the estimated time remaining. The preset settings
provide the recommended fabric care for the selected cycle.
See “Cycles.”
5. Select the desired Options. Not all Options are available with
all cycles. See “Options.”
6. Select the desired Modifiers (Soil Level, Temp, and Spin
Speed). Not all Modifiers are available with all Cycles and
Options. See “Modifiers.”
7. If desired, select the CYCLE END TONE. The signal is helpful
when you are washing items that should be removed from the
washer as soon as it stops.
8. To begin the wash cycle immediately
Select START (for approximately 1 second).
■ If you do not select START within 5 minutes of choosing a
cycle, the washer automatically shuts off.
■ When the wash cycle is complete, the CLOTHES CLEAN
status message is displayed, the door unlocks, and the
wash load can be removed from the washer. The washer
powers down automatically 5 minutes after the cycle is
complete and the CLOTHES CLEAN display goes off. To
power down the washer manually after the wash cycle is
complete, select PAUSE/CANCEL once.
9. To begin the wash cycle later
Select HOURS DELAY until the desired delay time (in hours)
shows in the Estimated Time Remaining display. Select
START. The countdown to the wash cycle will show in the
Status display.
UsingtheDispenser
Your new washer has a dispenser drawer with four separate
compartments for your laundry products—two are for detergent,
one is for liquid chlorine bleach, and one is for liquid fabric
softener. Laundry products are diluted and dispensed
automatically at the proper time during the wash cycle, making it
unnecessary for you to return to the washer during the cycle to
add them.
It is normal for small amounts of water to remain in the
dispensers when the wash cycle is complete.
Do not put laundry additives directly into the wash tub, for
example detergent boosters. Always use the proper dispensers
when adding laundry products.
Choosing the Right Detergent
Use only High Efficiency detergents. The package for this type of
detergent will be marked “HE” or “High Efficiency.” This wash
system, along with less water, will create too much sudsing with a
regular non-HE detergent. Using regular detergent will likely result
in washer errors, longer cycle times and reduced rinsing
performance. It may also result in component failures and
noticeable mold or mildew. HE detergents are made to produce
the right amount of suds for the best performance. Follow the
manufacturer's instructions to determine the amount of detergent
to use.
To fill dispenser compartments
1. Pull out the dispenser drawer.
2. Add the desired laundry product to the proper compartment.
3. Push in the dispenser drawer slowly and completely (to avoid
a spill).
Use only HE High Efficiency detergent.
Dispenser
A. Prewash detergent compartment
B. Separator
C. Main Wash detergent compartment
D. Dispenser release lever
E. Chlorine bleach compartment
F. Fabric softener compartment
A
B
C
D
E
F
13
Prewash detergent compartment
(Letter A in Dispenser Illustration)
Add detergent to this compartment when using the Pre Wash
option. Liquid or powdered detergent may be used in this
compartment. The detergent will automatically be dispensed
during Pre Wash if the Pre Wash option is selected.
■ Using High Efficiency (HE) detergent, add ¹⁄₃ the
recommended amount to the Prewash compartment and
²⁄₃ the recommended amount to the Main Wash
compartment.
■ Do not fill beyond the “MAX” level.
Main Wash detergent compartment
(Letter C in Dispenser Illustration)
Add liquid or powdered detergent to this compartment for your
main wash cycle. The detergent separator must always be in
place, either in the front or back position.
IMPORTANT: If you are using the Pre Wash, or Delay option,
powdered detergent must be used in the main wash
compartment since liquid detergents may seep out of the main
wash compartment during the prewash, or delay before the main
wash begins.
■ Do not fill beyond the “MAX” level.
■ Liquid or powdered color-safe bleach may be added to the
Main Wash compartment along with the same type of
detergent, liquid or powdered.
■ Liquid detergent: Put the SEPARATOR in the front position,
between the guides, as shown. There will be no gap between
the bottom of the wash cycle detergent compartment and the
bottom of the separator.
■ Powdered detergent: Put the SEPARATOR in the back
position, behind the guides, as shown. There will be a gap
between the bottom of the wash cycle detergent
compartment and the bottom of the separator.
NOTE: The separator will be in the POWDER (back) position
when shipped from the factory.
Chlorine bleach compartment
(Letter E in Dispenser Illustration)
Add no more than ¹⁄₃ cup (80 mL) liquid chlorine bleach to this
compartment. The bleach will be automatically diluted and
dispensed at the optimum time during the first rinse after the
wash cycle. This compartment cannot dilute powdered bleach.
■ Always measure liquid chlorine bleach. Use a measuring cup
with a pour spout; do not guess.
■ Do not fill beyond the “MAX” level.
NOTE: Overfilling could cause garment damage.
Fabric Softener compartment
(Letter F in Dispenser Illustration)
Add no more than ¼ cup (60 mL) liquid fabric softener to this
compartment. Fabric softener will be automatically dispensed in
the final rinse.
■ Do not fill beyond the “MAX” level.
Separator in front position, between guides
A. Separator
B. Guide
LIQUI
SO
A
B
Separator in back position, behind guides
A. Separator
B. Guide
LIQUI
SO
A
B
14
PausingorRestarting
1. To pause the washer at any time, select PAUSE/CANCEL.
2. To continue the cycle, select and hold START (for
approximately 1 second).
ChangingCycles,OptionsandModifiers
You can change the Cycle before START is selected. You can
change the factory default settings for the Modifiers (Soil Level,
Temp, and Spin Speed) and Options anytime before START is
selected and during the wash cycle.
NOTE: To help protect your garments, not all Options and
Modifiers can be selected with all wash cycles.
Cycles, Options and Modifiers can be changed anytime before
START is selected.
To cancel a cycle and select a new cycle
1. Select PAUSE/CANCEL twice.
2. Select desired cycle.
3. Select the desired Options.
4. Select and hold START (for approximately 1 second) to restart
the washer at the beginning of the new cycle.
To cancel a cycle
1. Select PAUSE/CANCEL twice.
2. The washer powers down, the door unlocks, and clothes can
be removed.
NOTE: If the water level or the temperature is too high, the
washer will drain automatically before the door unlocks.
To change Options or Modifiers after the cycle has
started
1. Select PAUSE/CANCEL.
2. Select the desired Options or Modifiers.
3. Select and hold START (for approximately 1 second) to
continue the cycle.
NOTE: Options and Modifiers can be changed anytime after
START is selected and before the start of the selected Option or
Modifier.
To drain the washer manually
1. Select PAUSE/CANCEL.
2. Select DRAIN/SPIN.
3. Select and hold START (for approximately 1 second) to begin
the drain.
4. When the spin is complete, the door unlocks. Items can be
removed from the washer.
StatusDisplay
Messages on the status display help you to follow the progress of
your washer. They also indicate when you can add an additional
item to the wash cycle and when the controls are locked.
Adding items
You can add items to the washer after the cycle has started for
Rapid Wash, Normal/Casual, Heavy Duty, White/Cotton, and
Sanitary if ADD A GARMENT message is displayed.
To add items
1. Select PAUSE/CANCEL. The washer door unlocks, and items
can be added.
2. To continue the cycle, close the door and select and hold
START (for approximately 1 second).
Cycle Complete
The CLOTHES CLEAN status message is displayed for 5 minutes
after the cycle is complete. The washer will then power down.
Locking controls
The Control Lock avoids unintended use of the washer. You can
also use the control lock feature to avoid unintended cycle or
option changes during a cycle. When the locked icon appears in
the display, all buttons are disabled except for Pause/Cancel and
Start. You can lock the controls while the washer is operating.
To lock the controls
Select and hold DRAIN/SPIN for 3 seconds.
The CONTROL LOCK icon illuminates.
To unlock the controls
Select and hold DRAIN/SPIN for 3 seconds until the CONTROL
LOCKED icon disappears.
Estimated Time Remaining
The cycle times vary automatically based on your water pressure,
water temperature, detergent, and clothes load. The cycle time
will be extended if oversudsing occurs or the load is unbalanced.
15
Cycles
Wash Cycles
Wash Cycles can be selected by pressing the button next to the
desired wash cycle. Each cycle is designed for different types of
fabric and soil levels.
■ Each cycle has a preset Soil Level (cycle time), Water
Temperature, Spin Speed and may have preset Options. The
preset settings provide the recommended fabric care for the
selected cycle.
■ The preset settings can be changed anytime before START is
selected. Not all Options and Modifiers are available with all
Cycles. (To change settings after the cycle has started, select
PAUSE/CANCEL, then select the desired settings. Select
START [for approximately 1 second] to continue the cycle.)
Preset cycle settings
Each cycle has a preset Soil Level (cycle time), Water
Temperature, and Spin Speed. The preset settings provide the
recommended fabric care for the selected cycle. See chart.
*The cycle times vary automatically based on your water
pressure, water temperature, detergent, and clothes load. The
cycle time will be extended if oversudsing occurs or the load is
unbalanced.
Sanitary
Use this cycle to clean heavily soiled colorfast fabrics. This cycle
combines a very hot water temperature and fast-speed tumbling
to help ensure the removal of heavy soils and stains. It is
recommended that you set your hot water heater to 120ºF (49ºC)
to ensure proper performance during this cycle. Extra high speed
spin helps shorten drying time.
White/Cotton
This cycle is especially designed for cleaning loads of soiled
white fabrics with the addition of bleach. Hot washing
temperatures assure optimal bleach activity. An additional rinse
provides optimal rinse performance to avoid chlorine residues on
your laundry. This cycle combines fast-speed tumbling, longer
wash time, and extra high speed spin to shorten drying time.
Heavy Duty
Use this cycle to wash loads of sturdy, colorfast fabrics and
normal to heavily soiled garments. This cycle combines
fast-speed tumbling, longer wash time, and extra high-speed
spin to shorten drying times. If the water temperature is lower
than needed for this cycle, the heater will warm the water to the
optimum temperature.
NOTE: Soil Treat is a default option for this cycle. To ensure best
performance, the water is heated as the cycle progresses. This
gradual heating assists in the removal of organic soils such as
blood.
Oversized Items
Use this cycle to wash large items such as blankets and
comforters. This cycle starts with a soak to thoroughly saturate
your large load. This is followed by medium wash action and
extra low spin speeds to maintain load balance.
Cycle
Estimated
Time*
(hr:min)
Soil
Level
Wash/
Rinse
Te mp
Spin
Speed
Sanitary (2:00) Normal Extra Hot/
Cold
Extra
High
White/ Cotton (1:10) Heavy Hot/
Cold
Extra
High
Heavy Duty (1:30) Heavy Hot/
Cold
Extra
High
Oversized
Items
(0:55) Normal Warm/
Cold
Extra
Low
Normal/
Casual
(0:45) Medium Warm/
Cold
High
Rapid
Wash
(0:35) Light Warm/
Cold
Extra
High
Delicate/Silk (0:35) Normal Cold/
Cold
No Spin
Wool/Hand
Wash
(0:35) Normal Cold/
Cold
Extra
Low
16
Normal/Casual
Use this cycle to wash loads of no-iron fabrics such as sport
shirts, blouses, casual business clothes, permanent press
blends, cottons and linens, and synthetic fabrics. This cycle
combines medium-speed tumbling, high-speed spin, and a load
cooling process to reduce wrinkling.
Rapid Wash
Use this cycle to wash small loads of 2-3 lightly soiled garments
that are needed in a hurry. This cycle combines fast-speed
tumbling, a shortened wash time, and extra high speed spin to
shorten drying time.
Delicate/Silk
Use this cycle to clean washable silk and ultra delicate garments.
(Check label instructions to make sure that garment is washable.)
This cycle gently tumbles and drains without spinning to gently
clean garments and minimize wrinkling. Garments will contain a
higher amount of water at the end of this cycle, because there is
no spinning action.
■ Use mesh garment bags to wash undergarments such as
underwire bras, items with strings, and small items such as
socks.
Wool/Hand Wash
Use this cycle to clean washable woolen and special care
garments. (Check label instructions to make sure that the
garment is washable.) Similar to the way garments are hand
washed in a sink, the wash action of this cycle combines periods
of extra low tumbling speeds and soaking. Low spin speeds
minimize wrinkling.
■ Use mesh garment bags to wash undergarments such as
underwire bras, items with strings, and small items such as
socks.
Favorite
Favorite allows you to store a customized wash cycle for future
use.
To customize a wash Cycle:
1. Select a cycle.
2. Select the desired OPTIONS.
3.
Select the desired MODIFIERS (Soil Level, Temp, and Spin Seed).
4. To save the cycle, press and hold FAVORITE (approximately
3 seconds) or until a beep sounds and the letters “SET” are
displayed on your machine.
5. Press START.
6. To reuse this cycle at another time, select FAVORITE and
press START.
Rinse/Spin
Use this cycle to get a rinse and spin only. This cycle combines
fast-speed tumbling and extra high speed spin. If desired, you
can reduce the spin speed by selecting the speed you want from
the SPIN SPEED modifier.
Rinse/Spin is useful for
■ Loads that need rinsing only.
■ Adding fabric softener to a load using the fabric softener
dispenser.
Drain/Spin
Use this cycle to drain your washer or to drain and spin your
wash load. The spin speed is preset to extra high. If desired, you
can reduce the spin speed by selecting the speed you want from
the SPIN SPEED modifier.
NOTE: Loads of synthetics, delicate fabrics, handwashables, and
woolens should be drained with no spin or low spin to avoid
fabric stress.
NormalSounds
As with any new product, you will hear sounds that you are not
accustomed to. You may hear various sounds when the door is
locked or unlocked, and during the washing, rinsing, or spinning
process. Between changes in wash actions, there will be
momentary pauses. You will hear water spraying and splashing
during the wash and rinse cycles. These new sounds and pauses
are part of normal washer operation. See “Troubleshooting.”
Options
You can customize your wash by adding Options to your cycle
selections. You can add or change an option after starting a cycle
anytime before the selected option begins. Not all Options are
available with all cycles.
■ See the “Laundry Guide” section for an overview of possible
options for each Cycle selection.
■ You can select more than one option for a cycle. Some
options cannot be added to some cycles, for example, Soil
Treat cannot be added to the Rapid Wash cycle.
■ If an option is available with a selected cycle, the light for that
option will illuminate when selected.
■ If an option is unavailable with a selected cycle, there will be a
short tone and the light for that option will not illuminate when
selected.
Prewash
Use this option for loads of heavily soiled items that need
pretreatment. This option adds a 15 minute prewash and drain to
the main wash cycle.
■ Add detergent to the Prewash and Main Wash compartments
of the Dispenser Drawer.
■ When using Prewash, do not use liquid detergent in the Main
Wash compartment. Use powdered detergent for the main
wash cycle (see “Using the Dispenser”).
Options
17
Soil Treat
Use this option for heavily soiled loads that need improved soil
treatment. When Soil Treat is selected, the water temperature of
the selected wash cycle is automatically set to Hot/Cold. The
water will then be gradually heated to a hot water temperature to
aid in stain removal. This option will provide optimal removal of
organic stains such as blood.
NOTE: If Soil Treat is selected with the Sanitary cycle, the water
will be heated to an extra hot temperature.
Energy Saver
The Energy Saver option allows you to increase your energy
savings on the higher temperature cycles (White/Cotton and
Heavy Duty) while maintaining cleaning performance by
lengthening the wash time by only 10 minutes.
NOTE: For the best energy performance, use the Normal/Casual
Cycle.
Hours Delay
To begin the wash cycle later select Hours Delay until the desired
delay time (in hours) shows in the Estimated Time Remaining
display. Select START. The countdown to the wash cycle will
show in the display window.
■
When delaying a cycle, use only powdered detergents in the
main wash compartment since liquid detergents may seep out
of the compartment during Delay, before the wash cycle begins.
Extra Spin
Use this option to add an additional spin to any cycle.
Cycle End Tone
This signal is helpful when you are removing items from the
washer as soon as it stops.
Normal Rinse
Consists of a two phase rinsing process that is effective for
everyday laundry.
Extra Rinse
A second rinse can be used to ensure the removal of detergent or
bleach residue from garments. This option provides an additional
rinse with the same water temperature as the first rinse.
Extended Rinse
This option provides the best rinse level, to allow for even better
detergent removal.
Modifiers
Preset cycle settings of water Temperature, Wash/Rinse, and
Spin Speed can be changed. You can change a modifier after
starting a cycle anytime before the selected Modifier begins. Not
all Modifiers are available with all options and cycles.
■ To change cycle time, select the SOIL LEVEL button until the
desired setting illuminates.
■ To change the water temperature, select the TEMP button
until the desired setting illuminates.
■ To change the spin speed, select the SPIN SPEED button
until the desired setting illuminates.
Wash/Rinse Temp
Select a water temperature based on the type of load you are
washing. Use the warmest water safe for fabrics. Follow garment
label instructions.
Warm rinses leave the loads dryer than cold rinses. Warm rinses
increase wrinkling. In cold climates, a warm rinse makes the load
more comfortable to handle. Cold rinses save energy.
Temperature Guide
*When used with Soil Treat option, the water is heated gradually
to assist in the removal of organic soils such as blood.
In wash water temperatures colder than 60°F (15.6°C),
detergents do not dissolve well. Soils may be difficult to remove.
Modifiers
Wash Water Temperature Suggested Fabrics
EXTRA HOT* Sturdy colorfast fabrics
Heavy soils
HOT* Whites and pastels
Heavy soils
WARM Bright colors
Moderate to light soils
COLD Colors that bleed or fade
Light soils
18
SENSORSURE
®
Automatic Temperature Control
SENSORSURE
®
automatic temperature control electronically
senses and maintains a uniform water temperature.
SENSORSURE
®
automatic temperature control regulates
incoming hot and cold water. The SENSORSURE
®
automatic
temperature control is automatically turned ON when a cycle is
selected. (See “Preset Cycle Settings” in “Cycles.”)
■ SENSORSURE
®
automatic temperature control works for the
wash temperature with Extra Hot/Cold, Hot/Cold, Warm/
Warm, Warm/Cold, and Cold/Cold settings.
■ SENSORSURE
®
automatic temperature control works for the
rinse temperature with the Warm/Warm setting.
LaundryGuide
Refer to this chart for suggested load types and their corresponding cycles. Listed to the right are the options available to each of these
washer cycles.
CYCLE SUGGESTED LOAD TYPE AVAILABLE OPTIONS
Pre
Wash
Soil
Treat
Energy
Saver
Hours
Delay
Extra
Spin
Extend
Rinse
Extra
Rinse
Sanitary Heavily soiled underwear, towels, work
clothes, diapers, etc.
✔✔ ✔✔✔✔
White/
Cotton
Heavily soiled whites made of cotton or
cotton blends
✔✔✔✔✔✔✔
Heavy Duty Moderately soiled work clothes,
underwear, towels, and denims, made of
sturdy fabrics
✔✔✔✔✔✔✔
Oversized
Items
Normally soiled blankets, comforters,
pillows, bulky jackets, etc
✔✔✔
Normal/
Casual
Lightly to normally soiled blouses, shirts,
pants, polos, made of cotton, polyester,
linen, and cotton blends
✔✔ ✔✔✔✔
Rapid Wash Lightly soiled casual wear or sportswear
made of cotton, polyester, nylon or cotton
blends
✔✔✔✔
Delicate/Silk Machine washable silks and delicates
such as dresses, blouses, skirts, slacks
and curtains
✔✔✔
Wool/Hand
Wash
Machine washable woolens and machine
washable special care items such as
sweaters, knits and dresses
✔✔
Rinse/Spin All load types ✔✔✔✔
Drain/Spin All load types ✔✔
19
LAUNDRY TIPS
Preparing clothes for washing
Follow these recommendations to help you prolong the life of
your garments.
■ Use only High Efficiency detergents. The package for this type
of detergent will be marked “HE” or “High Efficiency.” This
wash system, along with less water, will create too much
sudsing with a regular non-HE detergent. Using regular
detergent will likely result in washer errors, longer cycle times
and reduced rinsing performance. It may also result in
component failures and noticeable mold or mildew. HE
detergents are made to produce the right amount of suds for
the best performance. Follow the manufacturer's instructions
to determine the amount of detergent to use.
■ Close zippers, snaps, and hooks to avoid snagging other
items. Remove pins, buckles, and other hard objects to avoid
scratching the washer interior. Remove non-washable trim
and ornaments.
■ Empty pockets and turn them inside-out.
■ Turn down cuffs; brush away lint and dirt.
■ Turn synthetic knits inside-out to avoid pilling.
■ Tie strings and sashes so they will not tangle.
■ Mend tears, loose hems, and seams.
■ Treat spots and stains.
■ Stained or wet garments should be washed promptly for best
results.
■ Mix large and small items, avoid washing single items, and
load evenly.
■ Wash small items, such as infant socks, in a mesh garment
bags. To create a balanced load it is recommended that more
than one garment bag be used, and that each garment bag
be filled with equal amounts of material.
NOTE: If you are washing only small items, it is
recommended that more than one mesh garment bag be
used, and that each garment bag be filled with equal
amounts of material.
Sorting
■ Separate heavily soiled items from lightly soiled ones, even if
they would normally be washed together. Separate lint-givers
(towels, chenille) from lint-takers (corduroy, synthetics,
permanent press). When possible, turn lint-givers inside-out.
■ Separate dark colors from light colors, colorfast items from
noncolorfast items.
■ Sort by fabric and construction (sturdy cottons, knits, delicate
items).
Unloading
■ Remove clothes from washer after the cycle is completed.
Metal objects such as zippers, snaps, and buckles may rust if
left in the washer basket for a long time.
■ When unloading garments, occasionally check under the
rubber rim at the front of the tub for small items.
Loading
Use only HE High Efficiency detergent.
Loading suggestions (maximum size loads).
Heavy Work Clothes
4jeans
4workpants
4workshirts
2 sweatpants
2 sweatshirts
Towels
10 bath towels
10 hand towels
14 washcloths
Mixed Load
3 sheets (1 king, 2 twin)
4 pillowcases
3shirts
3blouses
9T-shirts
9shorts
10 handkerchiefs
Rapid Wash cycle
2dress shirts 1pair dress pants
20
WASHER CARE
CleaningYourWasher
Cleaning the door seal
1. Open the washer door and remove any clothing or items from
the washer.
2. Inspect the gray colored seal between the door opening and
the basket for stained areas. Pull back the seal to inspect
areas under the seal.
3. If stained areas are found, wipe down these areas of the seal,
using the procedure that follows.
a) Mix a dilute solution, using ³₄ cup (177.4 mL) of liquid
chlorine bleach, and 1 gal. (3.8 L) of warm tap water.
b) Wipe the seal area with the dilute solution, using a damp
cloth.
c) Let stand 5 minutes.
d) Wipe down area thoroughly with a dry cloth and let the
washer interior air dry.
IMPORTANT:
■ Wear rubber gloves when cleaning for prolonged periods.
■
Refer to the bleach manufacturer’s instructions for proper use.
Washer Monthly Maintenance Procedure
Your washer has a special cycle stored within the machine’s
programming. Pressing a specific combination of buttons will
enter this cleaning cycle. This cycle uses higher water volumes in
combination with liquid chlorine bleach to thoroughly clean the
inside of your washing machine.
NOTES:
■ Read these instructions completely before beginning the
cleaning process.
■ If necessary, the cleaning cycle may be interrupted by
pressing the PAUSE/CANCEL button. However, this will not
immediately stop the cycle. The machine will display “int”
(interrupt) and continue with several rinse and drain steps to
ensure that all remaining bleach is rinsed from the washer.
Begin procedure
1. Open the washer door and remove any clothing or items from
the washer.
2. Be sure the door is closed.
3. Open the dispenser drawer and remove the detergent divider
from the Main Wash detergent compartment. See “Using the
Dispenser” for instructions. No laundry products will be
added at this time; you will be required to add only liquid
chlorine bleach, at a later step.
4. Be sure the dispenser drawer is closed.
5. To enter the cycle, a specific combination of buttons must be
pressed.
■ Select the RINSE/SPIN button.
■ Select LOW Spin Speed.
■ Select WARM/COLD Water Temperature.
■ Select the EXTRA RINSE, Rinse Option.
■ Push the CYCLE END TONE button 4 times within
5 seconds to start the cycle. The door will lock, and filling
will begin.
NOTE: The water in the washer will dispense for a
moment, then the door will unlock, lock again, and then
the cycle will continue.
■ The machine will fill and run a short sensing cycle. This
will take approximately 3 minutes.
6. The washer will provide 4 short tones. Check the Estimated
Time Remaining display for the codes indicated below.
7. Add liquid chlorine bleach.
A. Seal
A
a) If the washer displays the letters “Ab” (Add Bleach) in the
Estimated Time Remaining display, you will hear 4 short
tones. Proceed to Step 6.
b) If the washer displays the letters “rL” (Remove Load) in
the Estimated Time Remaining display, an error tone will
sound. The door will unlock.
■ Open the door and remove the items from the washer.
■ Continue the cycle by pressing the START button.
NOTE: The water in the washer will dispense for a
moment, then the door will unlock, lock again, and
then the cycle will continue with another check for
items in the washer.
■ The machine will fill and run a short cycle to
determine whether any items have been left in the
washer. This will take approximately 3 minutes.
■ The washer will repeat Step 5 until it can determine
that there are no items in the washer and will display
“Ab” (Add Bleach).
a) If using the maintenance procedure for the first time, open
the dispenser drawer and immediately add 1 cup
(236.6 mL) liquid chlorine bleach to the Main Wash
detergent compartment. The liquid chlorine bleach should
immediately flow out of the dispenser.
b) For subsequent monthly maintenance procedures, open
the dispenser drawer and immediately add ¹⁄₃ cup
(78.8 mL) liquid chlorine bleach to the Main Wash
detergent compartment. The liquid chlorine bleach should
immediately flow out of the dispenser.
NOTES:
■ Water will be flowing into the dispenser drawer when
the bleach is added. This is normal.
■ Do not add any detergent to this cleaning cycle. Use
of more than 1 cup (236.6 mL) of bleach will cause
product damage over time.
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
KitchenAid Washer/Dryer Front-Loading Automatic Dishwasher Manuel utilisateur
- Catégorie
- Machines à laver
- Taper
- Manuel utilisateur
- Ce manuel convient également à
dans d''autres langues
Autres documents
-
Maytag Epic Z Manuel utilisateur
-
Whirlpool WFW8200TW01 Le manuel du propriétaire
-
-
-
-
-
-
-
Maytag MHWZ600TB - 27-in Front Load Washer Mode d'emploi
-
LG WD-12210BD Le manuel du propriétaire