GE PDS20MBWWW Le manuel du propriétaire

ge.com
Refrigerators
Bottom Freezer
3828JL8069D 197D4618P009    49-60503    01-07 JR
Safety Instructions  . . . . . . . . . . .2, 3
Operating Instructions
Additional Features  . . . . . . . . . . . . .9
Automatic Icemaker  . . . . . . . . . . .12
Controls  . . . . . . . . . . . . . . . . . . . .4–6
Crispers and Pans  . . . . . . . . . . . . .10
Freezer . . . . . . . . . . . . . . . . . . . . . .11
Shelves and Bins  . . . . . . . . . . . . .8, 9
Water Filter  . . . . . . . . . . . . . . . . . . .7
Care and Cleaning  . . . . . . . .13–15
Installation Instructions
Installing the Refrigerator  . . . .17–21
Installing the Water Line  . . . . .31–33
Preparing to Install 
the Refrigerator . . . . . . . . . . . . . . .16
Removing and Replacing the 
Freezer Drawer  . . . . . . . . . . . .22, 23
Reversing the Door Swing 
(Single Door Refrigerator 
Models only)  . . . . . . . . . . . . . .24–27
Removing and Replacing 
the Doors (Double Door 
Refrigerator Models only)  . . . .28–30
Troubleshooting Tips . . . . . . .34–38
Normal Operating Sounds  . . . . . .34
Consumer Support
Consumer Support  . . . . .Back Cover
Performance Data Sheet  . . . . . . . .45
Product Registration 
for Canadian Customers  . . . . .41, 42
Product Registration 
for U.S. Customers  . . . . . . . . .39, 40
Warranty for Canadian 
Customers  . . . . . . . . . . . . . . . . . . .43
Warranty for U.S. Customers . . . . .44
Réfrigérateurs
Congélateur inférieur
Refrigeradores
Congelador inferior
Write the model and serial 
numbers here:
Model #______________________
Serial # ______________________
Find these numbers on a label 
on the right side, near the top of
the refrigerator compartment.
Models 20 and 22
Manuel d’utilisation 
et d’installation
Owner’s Manual and
Installation Instructions
Manual del propietario
y instalación
La section française commence à la page 47
La sección en español empieza en la página 89

IMPORTANT SAFETY INFORMATION.

READ ALL INSTRUCTIONS BEFORE USING.

WARNING!

Use this appliance only for its intended purpose as described in this Owner’s Manual.

SAFETY PRECAUTIONS

When using electrical appliances, basic safety precautions should be followed, including the following:

■

■ This refrigerator must be properly installed

and located in accordance with the Installation

Instructions before it is used.

■

■ Do not allow children to climb, stand or hang

on the shelves in the refrigerator. They could

damage the refrigerator and seriously injure

themselves.

■

■ Do not touch the cold surfaces in the freezer

compartment when hands are damp or wet.

Skin may stick to these extremely cold surfaces.

■

■ Do not store or use gasoline or other flammable

vapors and liquids in the vicinity of this or any

other appliance.

■

■ Keep fingers out of the “pinch point” areas;

clearances between the doors and between

the doors and cabinet are necessarily small.

Be careful closing doors when children are

in the area.

■

■ In refrigerators with automatic icemakers,

avoid contact with the moving parts of the

ejector mechanism, or with the heating element

that releases the cubes. Do not place fingers or

hands on the automatic icemaking mechanism

while the refrigerator is plugged in.

■

■ Unplug the refrigerator before cleaning and

making repairs.

NOTE: We strongly recommend that any servicing be

performed by a qualified individual.

■

■ Setting either or both controls to 0 (off) does

not remove power to the light circuit.

■

■ Do not refreeze frozen foods which have

thawed completely.

PROPER DISPOSAL OF THE REFRIGERATOR

Child entrapment and suffocation are not problems

of the past. Junked or abandoned refrigerators are

still dangerous…even if they will sit for “just a few

days.” If you are getting rid of your old refrigerator,

please follow the instructions below to help prevent

accidents.

Before You Throw Away Your Old Refrigerator

or Freezer:

■ Take off the doors.

■ Leave the shelves in place so that children may

not easily climb inside.

Refrigerants

All refrigeration products contain refrigerants,

which under federal law must be removed prior

to product disposal. If you are getting rid of

an old refrigeration product, check with the

company handling the disposal about what

to do.

USE OF EXTENSION CORDS

Because of potential safety hazards under certain conditions, we strongly recommend against

the use of an extension cord.

However, if you must use an extension cord, it is absolutely necessary that it be a UL-listed (in the United

States) or a CSA certified (in Canada), 3-wire grounding type appliance extension cord having a grounding

type plug and outlet and that the electrical rating of the cord be 15 amperes (minimum) and 120 volts.

DANGER! RISK OF CHILD ENTRAPMENT

Consumer Support

Troubleshooting Tips

Operating Instructions Safety InstructionsInstallation Instructions

2

3

Consumer Support

Troubleshooting TipsOperating InstructionsSafety Instructions Installation Instructions

ge.com

WARNING!

HOW TO CONNECT ELECTRICITY

Do not, under any circumstances, cut or remove the third (ground) prong from the power cord.

For personal safety, this appliance must be properly grounded.

The power cord of this appliance is equipped

with a 3-prong (grounding) plug which mates

with a standard 3-prong (grounding) wall outlet to

minimize the possibility of electric shock hazard

from this appliance.

Have the wall outlet and circuit checked by a

qualified electrician to make sure the outlet is

properly grounded.

Where a standard 2-prong wall outlet is

encountered, it is your personal responsibility and

obligation to have it replaced with a properly

grounded 3-prong wall outlet.

The refrigerator should always be plugged into its

own individual electrical outlet which has a voltage

rating that matches the rating plate.

This provides the best performance and also

prevents overloading house wiring circuits which

could cause a fire hazard from overheated wires.

Never unplug your refrigerator by pulling on the

power cord. Always grip plug firmly and pull

straight out from the outlet.

Repair or replace immediately all power cords that

have become frayed or otherwise damaged. Do not

use a cord that shows cracks or abrasion damage

along its length or at either end.

When moving the refrigerator away from the

wall, be careful not to roll over or damage the

power cord.

READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.

SAVE THESE INSTRUCTIONS

4

About the controls with

temperature settings.

(for other models, see next page)

The temperature controls are preset in the factory at 37°F for the refrigerator compartment

and 0°F for the freezer compartment. Allow 24 hours for the temperature to stabilize to the

preset recommended settings.

The temperature controls can display both the SET temperature as well as the actual

temperature in the refrigerator and freezer. The actual temperature may vary slightly from

the SET temperature based on usage and operating environment.

Setting either or both controls to OFF stops cooling in both the freezer and refrigerator

compartments, but does not shut off electrical power to the refrigerator.

To change the temperature, press and release the

WARMER or COLDER pad. The SET light will come

on and the display will show the set temperature.

To change the temperature, tap either the

WARMER or COLDER pad until the desired

temperature is displayed. Refrigerator temperatures

can be adjusted between 34°F and 47°F and the

freezer temperatures can be adjusted between

–6°F and +8°F.

Once the desired temperature has been set,

the temperature display will return to the actual

refrigerator and freezer temperatures after 5

seconds. Several adjustments may be required.

Each time you adjust controls, allow 24 hours for the

refrigerator to reach the temperature you have set.

To turn the cooling system off, tap the WARMER pad

for either the refrigerator or the freezer until the

display shows OFF. To turn the unit back on, press the

COLDER pad for either the refrigerator or freezer.

The SET light will illuminate on the side you

selected. Then press the COLDER pad again (on the

side where the SET light is illuminated) and it will

go to the preset points of 0°F for the freezer and

37°F for the refrigerator. Setting either or both

controls to OFF stops cooling in both the freezer

and refrigerator compartments, but does not shut

off electrical power to the refrigerator.

Performance Air Flow System

Changing the Temperature

The Performance Air Flow System is designed to

maximize temperature control in the refrigerator

and freezer compartments. This unique special

feature consists of the Air Tower along the back

wall of the refrigerator and the Air Tunnel on the

bottom portion of the freezer rear wall. Placing

food in front of the louvers on these components

will not affect performance.

NOTE: The refrigerator is shipped with protective film covering the temperature controls.

If this film was not removed during installation, remove it now.

Consumer Support

Troubleshooting Tips

Operating Instructions Safety InstructionsInstallation Instructions

Consumer Support

Troubleshooting TipsOperating InstructionsSafety Instructions Installation Instructions

5

About TurboCool.

™

(on some models) ge.com

How it Works

TurboCool rapidly cools the refrigerator

compartment in order to more quickly

cool foods. Use TurboCool when adding a

large amount of food to the refrigerator

compartment, putting away foods after they

have been sitting out at room temperature

or when putting away warm leftovers. It can

also be used if the refrigerator has been

without power for an extended period.

Once activated, the compressor will turn on

immediately and the fans will cycle on and

off at high speed as needed for eight hours.

The compressor will continue to run until

the refrigerator compartment cools to

approximately 34°F (1°C), then it will cycle

on and off to maintain this setting. After 8

hours, or if TurboCool is pressed again, the

refrigerator compartment will return to

the original setting.

How to Use

Press TurboCool. The refrigerator

temperature display will show .

After TurboCool is complete, the

refrigerator compartment will return

to the original setting.

NOTES: The refrigerator temperature

cannot be changed during

TurboCool.

The freezer temperature is not

affected during TurboCool.

When opening the refrigerator

door during TurboCool, the fans

will continue to run if they have

cycled on.

About Door Alarm (on some models)

The door alarm will sound if either

door is open for more than 2 minutes.

The beeping stops when you close

the door.

Consumer Support

Troubleshooting Tips

Operating Instructions Safety InstructionsInstallation Instructions

About the controls with numbered settings.

Initially, set the refrigerator control at 5 and the freezer control at 5 and allow 24 hours

for the temperature to stabilize.

Several adjustments may be required. Adjust the controls one increment at a time, and

allow 24 hours after each adjustment for the refrigerator to reach the temperature you

have set.

Setting either or both controls to 0 stops cooling in both the refrigerator and freezer

compartments, but does not shut off electrical power to the refrigerator.

NOTE: The refrigerator is shipped with protective film covering the temperature controls.

If this film was not removed during installation, remove it now.

Performance Air Flow System

The Performance Air Flow System is designed to

maximize temperature control in the refrigerator

and freezer compartments. This unique special

feature consists of the Air Tower along the back

wall of the refrigerator and the Air Tunnel on the

bottom portion of the freezer rear wall. Placing

food in front of the louvers on these components

will not affect performance.

6

Water Filter Cartridge

The water filter cartridge is located in the

back upper right corner of the refrigerator

compartment.

When to Replace the Filter

There is a replacement indicator

light for the water filter cartridge on the

temperature display. This light will turn

orange to tell you that you need to replace

the filter soon. The filter cartridge should

be replaced when the replacement

indicator light turns red or if the flow

of water to the dispenser or icemaker

decreases.

Installing the Filter Cartridge

If you are replacing the cartridge,

first remove the old one. Open the

cartridge cover by pressing in on the

tab at the front and pulling down.

Remove the cartridge by slowly rotating

it counterclockwise. A small amount of

water may drip down.

CAUTION: If air has been trapped

in the system, the filter cartridge may be ejected as

it is removed. Use caution when removing.

Remove the protective foil from the

end of the cartridge.

Lining up the arrow on the cartridge

and the cartridge holder, slowly rotate

the cartridge clockwise until it stops.

When the cartridge is properly

installed, you will feel it “click” as it

locks into place. The blade on the end

of the cartridge should be positioned

vertically. Do not overtighten.

Close the cartridge cover.

Run water from the dispenser for

3 minutes (about 1

1

⁄2 gallons) to clear

the system and prevent sputtering.

See To Use the Dispenser section.

Press and hold the RESET WATER FILTER

pad for 3 seconds.

NOTE: A newly-installed water filter cartridge

may cause water to spurt from the dispenser.

Filter Bypass Plug

You must use the filter bypass plug when a

replacement filter cartridge is not available.

The icemaker will not operate without the

filter or filter bypass plug.

Replacement Filters:

To order additional filter cartridges

in the United States, visit our Website,

ge.com, or call GE Parts and Accessories,

800.626.2002.

Filter Model GSWF

Customers in Canada should consult

the yellow pages for the nearest Mabe

Service Center.

About the water filter. (on some models) ge.com

7

Consumer Support

Troubleshooting TipsOperating InstructionsSafety Instructions Installation Instructions

(on some models)

Consumer Support

Troubleshooting Tips

Operating Instructions Safety InstructionsInstallation Instructions

8

Rearranging the Shelves

To remove:

Tilt the shelf up at the front.

Lift the shelf up at the back and

bring the shelf out.

To replace:

While tilting the shelf up, insert the top

hook at the back of the shelf in a slot

on the track.

Lower the front of the shelf until the

bottom of the shelf locks into place.

Spillproof Shelves (on some models)

Spillproof shelves have special edges to

help prevent spills from dripping to lower

shelves. To remove or replace the shelves,

see Rearranging the Shelves.

About the shelves and bins.

Not all features are on all models.

Some models have wire shelves that

can be adjusted in the same manner.

Shelves in the refrigerator compartment are adjustable.

Refrigerator Compartment

Slide-Out Spillproof Shelf (on some models)

The slide-out spillproof shelf allows you

to reach items stored behind others. The

special edges are designed to help prevent

spills from dripping to lower shelves.

To remove:

Remove all items from shelf.

Slide the shelf out until it stops.

Lift the front edge of the shelf until the

central tabs are above the front bar.

Continue pulling the shelf forward

until it can be removed.

To replace:

Place the rear shelf tabs just in front of

the central notches on the shelf frame.

Slide the shelf in until the central tabs

are slightly behind the front bar.

Lower the shelf into place until it is

horizontal and slide the shelf in.

Make sure that the shelf sits flat after reinstallation

and doesn’t move freely from side to side.

Make sure you push the shelves all the way in

before you close the door.

Non-Adjustable Shelves on the Door

To remove: Lift the shelf straight up, then

pull out.

To replace: Engage the shelf in the molded

supports on the door and push down.

It will lock in place.

Adjustable Bins on the Door

Adjustable bins can easily be carried from

refrigerator to work area.

To remove: Lift bin straight up, then

pull out.

To replace or relocate: Engage the bin in the

molded supports of the door, and push in.

Bin will lock in place.

The snugger helps prevent tipping, spilling

or sliding of small items stored on the door

shelf. Grip the finger hold near the rear of

the snugger and move it to fit your needs.

Snugger

Finger hold

About the additional features.

Not all features are on all models.

Shelf Saver Rack (on some models)

Slide-out beverage rack holds twelve cans of

soda or two wine/water bottles (lengthwise).

It can be removed for cleaning.

To remove, slide the rack out to the stop

position, lift the rack up and past the stop

position and lift it out.

ge.com

9

Consumer Support

Troubleshooting TipsOperating InstructionsSafety Instructions Installation Instructions

Consumer Support

Troubleshooting Tips

Operating Instructions Safety InstructionsInstallation Instructions

About the crispers and pans.

Not all features are on all models.

Fruit and Vegetable Crisper

Excess water that may accumulate in the

bottom of the drawers or under the drawers

should be wiped dry.

Adjustable Humidity Crisper (on some models)

Slide the control all the way to the

HIGH setting to provide high humidity

recommended for most vegetables.

Slide the control all the way to the LOW

setting to provide lower humidity levels

recommended for most fruits.

LOW HIGH

LOW

HIGH

Snack Pan (on some models)

This pan can be moved to the most useful

location for your family’s needs.

To remove, slide the pan out to the stop

position, lift the pan up and past the stop

position and lift it out.

Adjustable Temperature Deli Pan (on some models)

When the pan is placed in the 7th slot from

the bottom of the track and the lever is set

at COLDEST, air from the freezer is forced

around the pan to keep it very cold.

You can move the pan to any location if

you don’t want the extra cold storage.

The settings can be adjusted anywhere

between cold and coldest .

When set at cold, the pan will stay at the

normal refrigerator temperature.

The coldest setting provides the coldest

storage area.

10

Crisper Removal

To Remove:

These drawers can be removed easily by

lifting up slightly while pulling the drawer

past the stop location.

When the door cannot be fully opened,

remove the drawer farthest from the door

first. Make sure the drawer closest to the

door is fully closed. There is a latch at the

front of the center slide rail. Push down on

the latch and slide the center slide rail, to

which the drawer is attached, away from the

door. Remove the drawer.

Freezer Shelves and Baskets

Depending on your model, your freezer

may feature:

A deep full-width basket

A shallow full-width basket

A half-width basket

A full-width wire shelf

A shelf above the ice storage bin

Basket/Shelf Removal

To remove the deep full-width baskets on

freezer door models, the shallow full-width

basket and the full-width wire shelf:

Pull the basket/shelf out to the stop

location.

Lift the front up and over the stop

location.

Lift the basket/shelf up and out.

To remove the deep full-width basket on

freezer drawer models:

Open the freezer drawer until it stops.

The freezer basket rests on a frame

inside the freezer drawer. Lift the basket

up at the back.

Lift the front up and lift the entire

basket up and out of the drawer.

To remove the half-width basket:

Pull the basket out to the stop location.

Lift the basket up at the front to release

it from the slides.

Lift the back up and out of the slide.

When replacing the basket, make sure that

the wire tabs and wire hooks on the sides

of the basket go into the slots in the top

of the upper basket slides.

NOTE: Always be sure to fully close this

basket. You will know it is fully closed when

you feel it “click” into place.

To remove the shelf above the ice bin:

Pull the shelf straight out.

About the freezer. ge.com

Not all features are on all models.

11

Consumer Support

Troubleshooting TipsOperating InstructionsSafety Instructions Installation Instructions

Appearance and features may vary

Appearance may vary

Shelf

Ice Bin

or

Hook

Tab

About the automatic icemaker.

12

Automatic Icemaker

(on some models)

The icemaker will produce seven cubes

per cycle—approximately 100–130 cubes

in a 24-hour period, depending on freezer

compartment temperature, room

temperature, number of door openings

and other use conditions.

See below for how to access ice and reach

the power switch.

If the refrigerator is operated before the

water connection is made to the icemaker,

set the power switch in the O (off) position.

The icemaker power light will turn green

when the freezer light switch is pressed in

or when the freezer door is closed.

When the refrigerator has been connected

to the water supply, set the power switch to

the l (on) position.

The icemaker will fill with water when it

cools to 15°F (–10°C). A newly installed

refrigerator may take 12 to 24 hours to begin

making ice cubes.

You will hear a buzzing sound each time

the icemaker fills with water.

Throw away the first few batches of ice to

allow the water line to clear.

Be sure nothing interferes with the sweep

of the feeler arm.

When the bin fills to the level of the feeler

arm, the icemaker will stop producing

ice. It is normal for several cubes to be

joined together.

If ice is not used frequently, old ice cubes

will become cloudy, taste stale and shrink.

NOTE: In homes with lower-than-average water

pressure, you may hear the icemaker cycle multiple

times when making one batch of ice.

A newly installed refrigerator may take 12 to 24 hours to begin making ice.

Icemaker

Feeler Arm

Power

Switch

Green

Power Light

Accessing Ice and Reaching

the Power Switch

To reach the icemaker power switch, pull the

shelf above the ice bin straight out. Always

be sure to replace the shelf.

To access ice, simply pull the bin forward.

To access ice.

Shelf

Ice Bin

To reach the power switch.

Shelf

Ice Bin

Icemaker Accessory Kit

If your refrigerator did not come already

equipped with an automatic icemaker,

an icemaker accessory kit is available at

extra cost.

Check the back of the refrigerator for

the specific icemaker kit needed for

your model.

Consumer Support

Troubleshooting Tips

Operating Instructions Safety InstructionsInstallation Instructions

To Use the Dispenser (on some models)

The water dispenser is located on the left

wall inside the refrigerator compartment.

To dispense water:

Hold the glass against the recess.

Push the water dispenser button.

Hold the glass underneath the

dispenser for 2–3 seconds after

releasing the dispenser button.

Water may continue to dispense

after the button is released.

If no water is dispensed when the refrigerator is first

installed, there may be air in the water line system.

Press the dispenser button for at least 2 minutes to

remove trapped air from the water line and to fill the

water system. During this process, the dispenser

noise may be loud as the air is purged from the

water line system. To flush out impurities in the

water line, throw away the first 6 glassfuls of water.

NOTE: To avoid water deposits, the dispenser

should be cleaned periodically by wiping with a

clean cloth or sponge.

Consumer Support

Troubleshooting TipsOperating InstructionsSafety Instructions Installation Instructions

Care and cleaning of the refrigerator.

ge.com

13

Cleaning the Outside

The door handles and trim. Clean with a cloth

dampened with soapy water. Dry with a soft

cloth. Do not use wax on the door handles

and trim.

Keep the outside clean. Wipe with a clean

cloth lightly dampened with kitchen

appliance wax or mild liquid dish

detergent. Dry and polish with a clean,

soft cloth.

Do not wipe the refrigerator with a soiled dish

cloth or wet towel. These may leave a residue

that can erode the paint. Do not use scouring

pads, powdered cleaners, bleach or cleaners

containing bleach because these products can

scratch and weaken the paint finish.

The stainless steel panels and door handles.

Stainless steel (on some models) can be

cleaned with a commercially available

stainless steel cleaner. A spray-on stainless

steel cleaner works best.

Do not use appliance wax or polish

on the stainless steel.

Cleaning the Inside

To help prevent odors, leave an open box of

baking soda in the refrigerator and freezer

compartments.

Unplug the refrigerator before cleaning. If this

is not practical, wring excess moisture out

of sponge or cloth when cleaning around

switches, lights or controls.

Use an appliance wax polish on the inside

surface between the doors.

Use warm water and baking soda solution—

about a tablespoon (15 ml) of baking soda

to a quart (1 liter) of water. This both cleans

and neutralizes odors. Rinse and wipe dry.

After cleaning the door gaskets, apply a

thin layer of petroleum jelly to the door

gaskets at the hinge side. This helps keep

the gaskets from sticking and bending out

of shape.

Avoid cleaning cold glass shelves with hot water

because the extreme temperature difference may

cause them to break. Handle glass shelves

carefully. Bumping tempered glass can cause

it to shatter.

Do not wash any plastic refrigerator parts in

the dishwasher.

14

Consumer Support

Troubleshooting Tips

Operating Instructions Safety InstructionsInstallation Instructions

For long vacations or absences, remove

food and unplug the refrigerator. Move

the freezer control to the 0 (off) position,

and clean the interior with a baking soda

solution of one tablespoon (15 ml) of

baking soda to one quart (1 liter) of water.

Leave the doors open.

Set the icemaker power switch to the O (off)

position and shut off the water supply to

the refrigerator.

If the temperature can drop below

freezing, have a qualified servicer drain the

water supply system (on some models) to

prevent serious property damage due to

flooding.

Care and cleaning of the refrigerator.

Behind the Refrigerator

Be careful when moving the refrigerator

away from the wall. All types of floor

coverings can be damaged, particularly

cushioned coverings and those with

embossed surfaces.

Pull the refrigerator straight out and return

it to position by pushing it straight in.

Moving the refrigerator in a side direction

may result in damage to the floor covering

or refrigerator.

When pushing the refrigerator back, make sure

you don’t roll over the power cord or icemaker

supply line (on some models).

Preparing for Vacation

Preparing to Move

Secure all loose items such as base grille,

shelves and drawers by taping them

securely in place to prevent damage.

When using a hand truck to move the

refrigerator, do not rest the front or back

of the refrigerator against the hand truck.

This could damage the refrigerator. Handle

only from the sides of the refrigerator.

Be sure the refrigerator stays in an upright

position during moving.

Refrigerator Lights

CAUTION: Light bulbs may be hot.

Unplug the refrigerator.

The bulbs are located at the top of the

refrigerator compartment behind the

controls. To remove the light shield,

grasp the shield at the back and pull

out to release the tabs at the back.

Rotate the shield down and then

forward to release the tabs at the front

of the shield.

After replacing with an appliance bulb

of the same or lower wattage, replace

the shield.

Plug the refrigerator back in.

Freezer Light

Replacing the light bulbs. ge.com

Turning the control to the 0 (off) position does not remove power to the light circuit.

15

Consumer Support

Troubleshooting TipsOperating InstructionsSafety Instructions Installation Instructions

Appearance may vary

CAUTION: Light bulbs may be hot.

Unplug the refrigerator.

The bulb is located at the top of the

freezer inside a light shield. To remove

the shield, grasp the shield at the back

and pull out to release the tabs at the

back.

Rotate the shield down and then

forward to release the tabs at the front

of the shield.

After replacing with an appliance bulb

of the same or lower wattage, replace

the shield.

Plug the refrigerator back in.

Installation

Refrigerator

Instructions

Models 20 and 22

Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: ge.com

In Canada, call 1.800.361.3400 or Visit our Website at: www.geappliances.ca

BEFORE YOU BEGIN

Read these instructions completely

and carefully.

•

IMPORTANT — Save these

instructions for local inspector’s use.

•

IMPORTANT — Observe all

governing codes and ordinances.

• Note to Installer – Be sure to leave these

instructions with the Consumer.

• Note to Consumer – Keep these

instructions for future reference.

• Skill level – Installation of this appliance

requires basic mechanical skills.

• Completion time – Refrigerator Installation

20 minutes

Water Line Installation

30 minutes

• Proper installation is the responsibility of

the installer.

• Product failure due to improper installation

is not covered under the Warranty.

PREPARATION

MOVING THE REFRIGERATOR INDOORS

If the refrigerator will not fit through a doorway,

the refrigerator door and freezer drawer or door

(depending on model) can be removed.

• To remove the refrigerator door, see Step 1

in the Reversing the Door Swing section.

• To remove the freezer drawer, see the

Removing the Freezer Drawer section.

• To remove the freezer door, see Steps 2

and 3 in the Reversing the Door Swing

section.

PREPARATION (cont.)

WATER SUPPLY TO THE ICEMAKER AND

DISPENSER (ON SOME MODELS)

If the refrigerator has an icemaker, it will have

to be connected to a cold water line. A GE water

supply kit (containing tubing, shutoff valve,

fittings and instructions) is available at extra

cost from your dealer, by visiting our Website

at ge.com (in Canada at www.geappliances.ca)

or from Parts and Accessories, 800.626.2002 (In

Canada 1.888.261.3055).

TOOLS YOU MAY NEED

Adjustable Wrench

1/4″ Outer Diameter

Compression Nut

and Ferrule (sleeve)

(icemaker models only)

Phillips Head Screwdriver

16

3/8″ and 10 mm Socket

Ratchet/Driver

3/32″ Allen wrench

supplied for use on

Stainless steel

refrigerator handles

(on some models)

1/4″ Allen wrench supplied

for changing handle

fasteners location

(on some models)

Installation Instructions

INSTALLING THE REFRIGERATOR

REFRIGERATOR LOCATION

• Do not install the refrigerator where the

temperature will go below 60°F (16°C) because it

will not run often enough to maintain proper

temperatures.

• Do not install the refrigerator where the

temperature will go above 100°F (37°C) because it

will not perform properly.

• Install it on a floor strong enough to support it fully

loaded.

CLEARANCES

Allow the following clearances for ease of installation,

proper air circulation and plumbing and electrical

connections.

Sides 1/8″ (4 mm)

Top 1″ (25 mm)

Back 1″ (25 mm)

CONNECTING THE REFRIGERATOR

TO THE HOUSE WATER LINE

(icemaker and dispenser models)

A cold water supply is required for automatic

icemaker operation. If there is not a cold water

supply, you will need to provide one. See

Installing the Water Line section.

NOTES:

• Before making the connection to the

refrigerator, be sure the refrigerator power cord

is not plugged into the wall outlet.

• If your refrigerator does not have a water filter,

we recommend installing one if your water

supply has sand or particles that could clog the

screen of the refrigerator’s water valve. Install it

in the water line near the refrigerator. If using

GE SmartConnect

™

Refrigerator Tubing Kit, you

will need an additional tube (WX08X10002) to

connect the filter. Do not cut plastic tube to

install filter.

1

REMOVE TOP CAP (cont.)

(on some models)

REINSTALL DOORS, DRAWERS AND TOP CAP

Carefully lower the door onto the center hinge.

Reinstall top hinge. NOTE: Ensure the door is

properly aligned to the case top to avoid

readjustment of the door during top cap

reinstallation.

Place cap over the top of the refrigerator. Reinstall

the original screws in the top and back of the cap.

Reinstall the bottom freezer drawer. Refer to

“Replacing the Freezer Drawer” section.

E

F

G

A.

Top Hinge

B.

REMOVE TOP CAP

(on some models)

• IMPORTANT NOTE: This refrigerator is 34-1/2″ deep.

Doors and passageways leading to the installation

location must be at least 36″ wide in order to

leave the doors and handles attached to the

refrigerator while transporting it into the installation

location. If passageways are less than 36″, the

refrigerator doors and handles can easily be scratched

and damaged. The top cap and doors can be removed

to allow the refrigerator to be safely moved indoors.

Start with Step A.

• If it is not necessary to remove doors, skip Step A.

Leave tape and all packaging on doors until the

refrigerator is in the final location.

• SKID REMOVAL: Tilt refrigerator to each side to

remove skid.

• NOTE: Use a padded hand truck to move this

refrigerator. Place the refrigerator on the hand

truck with a side against the truck. We strongly

recommend that TWO PEOPLE move and complete

this installation.

Locate and remove the two Phillips head screws

on the top of the refrigerator. Remove the two

screws on each side at the rear of the top cap.

Lift off and remove top cap.

Remove the fresh-food door. Refer to Steps 1

through 3 of “Reversing the Door Swing” section.

Remove the bottom freezer drawer. Refer to

“Removing Freezer Drawer” section.

Move refrigerator to the installation location.

A

B

C

D

17

CONNECTING THE REFRIGERATOR

TO THE HOUSE WATER LINE

(cont.)

If you are using copper tubing, place a

compression nut and ferrule (sleeve) onto

the end of the tubing coming from the

house cold water supply.

If you are using the GE SmartConnect

™

tubing, the nuts are already assembled to

the tubing.

If you are using copper tubing, insert

the end of the tubing into the refrigerator

connection, at the back of the refrigerator,

as far as possible. While holding the

tubing, tighten the fitting.

If you are using GE SmartConnect

™

tubing, insert the molded end of the

tubing into the refrigerator connection,

at the back of the refrigerator, and tighten

the compression nut until it is hand tight.

Then tighten one additional turn with a

wrench. Overtightening may cause leaks.

Fasten the tubing into the clamp provided

to hold it in position. You may need to pry

open the clamp.

One of the illustrations below will look like

the connection on your refrigerator.

Icemaker-Ready models

Icemaker-Installed Models

18

Installation Instructions

INSTALLING THE REFRIGERATOR

(cont.)

1

A

B

C

1/4″ Tubing

Tubing Clamp

1/4″

Compression

Nut

Ferrule

(sleeve)

SmartConnect

™

Tubing

Refrigerator

Connection

TURN ON THE WATER SUPPLY

(icemaker and dispenser models)

Turn the water on at the shutoff valve

(house water supply) and check for

any leaks.

2

PLUG IN THE REFRIGERATOR

On models with an icemaker, before

plugging in the refrigerator, make sure

the icemaker power switch is set to the

O (off) position.

See the grounding information attached

to the power cord.

3

PUT THE REFRIGERATOR

IN PLACE

Move the refrigerator to its final location.

4

Tubing

Clamp

1/4″

Compression

Nut

Ferrule

(sleeve)

SmartConnect

™

Tubing

Refrigerator

Connection

1/4″

Copper

Tubing

Installation Instructions

REMOVE THE FRESH FOOD

DOOR HANDLE

(For placement in the installation location or

reversal of the handles – on some models)

Stainless steel (on some models):

REMOVING

THE DOOR

HANDLE: Loosen

the set screws with

the 3/32″ Allen

wrench and

remove the handle.

NOTE: For Double

Door models

follow the same

procedure on the

opposite door.

REVERSING THE

DOOR HANDLE:

• Remove the

handle mounting

fasteners with a 1/4″ Allen wrench and transfer

the handle mounting fasteners to the right side.

• Remove and transfer the plug button and logo

badge to the left side of the fresh food door.

NOTE: Use a flat plastic edge to prevent damaging

the door. Remove any adhesive on the door with

a mild detergent. Remove the paper covering on

the adhesive backing on the logo badge prior to

carefully attaching the badge to the door.

Plastic handle (on some models):

REMOVING THE

DOOR HANDLE:

Slide the handle

up on the handle

mounting

fasteners and

remove the

handle.

For some models,

depress the tab

on the underside

of the handle and

slide the handle

up and off of the

mounting

fasteners.

REVERSING THE DOOR HANDLE:

• Remove the handle mounting fasteners with a

3/8″ or 10 mm socket wrench and transfer the

handle mounting fasteners to the right side.

• Remove and transfer the plug button and logo

badge to the left side of the fresh food door.

NOTE: Use a flat plastic edge to prevent

damaging the door. Remove any adhesive on

the door with a mild detergent. Remove the

paper covering on the adhesive backing on the

logo badge prior to carefully attaching the badge

to the door.

A

5

After removing the handle: Move the small plug

button from the top right side of the door top and

insert it into the hole on the opposite side.

Small

Plug

Button

A

B

A

B

Mounting

Fasteners

Mounting Fasteners

Plug

Button

Plug

Button

(appearance may vary)

Badge

(appearance may vary)

REMOVE THE FREEZER DOOR

HANDLE

Stainless steel and some plastic handles:

Loosen the set screws located on the underside

of the handle with the 3/32″ (or 1/8″ on some

models) Allen wrench and remove the handle.

NOTE: If the handle mounting fasteners need to

be tightened or removed use a 1/4″ Allen wrench.

Plastic handle:

Slide the handle to the right on the handle

mounting fasteners and remove the handle.

NOTE: If the handle mounting fasteners need to

be tightened or removed use a 3/8″ or 10 mm

socket wrench.

A

6

A

Mounting

fasteners

Slots on back

of handle

(appearance may vary)

A

19

ATTACH THE FREEZER DOOR

HANDLE

Stainless steel and some plastic handles:

Attach the handle firmly to the mounting

fasteners and tighten the set screws on the

bottom of the handle with a 3/32″ (or 1/8″

on some models) Allen wrench.

Plastic handle:

Attach the handle to the mounting fasteners by

aligning the slots with the mounting fasteners.

Slide it to the left until it is firmly locked into

position.

NOTE: A properly locked handle will be centered

on the freezer.

A

Installation Instructions

INSTALLING THE REFRIGERATOR

(cont.)

20

ATTACH THE FRESH FOOD

DOOR HANDLE

Stainless steel handle:

Attach the handle

to the handle

mounting

fasteners and

tighten the set

screws with a

3/32″ Allen

wrench.

NOTE: For

Double Door

models follow the

same procedure

on the opposite

door.

Plastic handle:

Attach the handle to the handle mounting

fasteners by aligning the slots with the handle

mounting fasteners.

Slide it down until it is firmly locked into

position.

A

7

A

Mounting

Fasteners

Plug

Button

Badge

(appearance may vary)

Mounting

fasteners

Slots on back of

handle

A

8

A

Mounting

fasteners

Slots on back

of handle

(appearance may vary)

A

(appearance may vary)

La page charge ...

GE PDS20MBWWW Le manuel du propriétaire

GE PDS20MBWWW Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents