Makita LS0714FL Manuel utilisateur

1

INSTRUCTION MANUAL

MANUEL D'INSTRUCTION

MANUAL DE INSTRUCCIONES

DOUBLE INSULATION

DOUBLE ISOLATION

DOBLE AISLAMIENTO

IMPORTANT: Read Before Using.

IMPORTANT: Lire avant usage.

IMPORTANTE: Leer antes de usar.

Slide Compound Saw

Scie Multi Coupe

Sierra de Inglete Telescópica

LS0714

LS0714FL

005515

2

ENGLISH (Original instructions)

SPECIFICATIONS

Models LS0714 / LS0714FL

Blade diameter 190 mm (7-1/2")

Hole (arbor) diameter 15.88 mm (5/8")

Max. Miter angle Left 47° , Right 57°

Max. Bevel angle Left 45°, Right 5°

Max. Cutting capacities (H x W) with blade 190 mm (7-1/2") in diameter.

Bevel angle

Miter angle 45° (left) 0° 5° (right)

* 45 mm x 265 mm Note1

(1 - 3/4" x 10 - 3/8")

* 60 mm x 265 mm Note 1

(2 - 3/8" x 10 - 3/8") -----

0° 40 mm x 300 mm

(1 - 9/16" x 11 - 3/4")

52 mm x 300 mm

(2 - 1/16" x 11 - 3/4")

40 mm x 300 mm

(1 - 9/16" x 11 - 3/4")

* 45 mm x 185 mm Note2

(1 - 3/4" x 7 - 1/4")

* 60 mm x 185 mm Note 2

(2 - 3/8" x 7 - 1/4")

45° (left and right) 40 mm x 212 mm

(1 - 9/16" x 8 - 3/8")

52 mm x 212 mm

(2 - 1/16" x 8 - 3/8")

-----

* 60 mm x 145 mm Note 3

(2 - 3/8" x 5 - 3/4")

57° (right) ----- 52 mm x 163 mm

(2 - 1/16" x 6 - 3/8")

-----

(Note)

* mark indicates that a wood facing with the following thickness is used.

1: When using a wood facing 20 mm (13/16") thick.

2: When using a wood facing 15 mm (9/16") thick.

3: When using a wood facing 10 mm (3/8") thick.

No load speed (RPM) 6,000/min.

Laser Type (LS0714FL only) Red Laser 650 nm, 1mW ( Laser Class 2 )

Dimensions (L x W x H) 670 mm x 430 mm x 458 mm (26 - 3/8" x 17" x 18")

Net weight LS0714: 13.1 kg (28.9 lbs), LS0714FL: 13.7 kg (30.2 lbs)

• Due to our continuing programme of research and development, the specifications herein are subject to change without notice.

• Specifications may differ from country to country.

• Weight according to EPTA-Procedure 01/2003

USA007-2

For Your Own Safety Read

Instruction Manual

Before Operating Tool

Save it for future reference

GENERAL SAFETY

PRECAUTIONS

(For All Tools)

1. KNOW YOUR POWER TOOL. Read the owner's

manual carefully. Learn the tool's applications

and limitations, as well as the specific

potential hazards peculiar to it.

2. KEEP GUARDS IN PLACE and in working

order.

3. REMOVE ADJUSTING KEYS AND WRENCHES.

Form habit of checking to see that keys and

adjusting wrenches are removed from tool

before turning it on.

4. KEEP WORK AREA CLEAN. Cluttered areas

and benches invite accidents.

3

5. DO NOT USE IN DANGEROUS ENVIRONMENT.

Do not use power tools in damp or wet

locations, or expose them to rain. Keep work

area well lighted. Do not use tool in presence

of flammable liquids or gases.

6. KEEP CHILDREN AWAY. All visitors should be

kept safe distance from work area.

7. MAKE WORKSHOP KID PROOF with padlocks,

master switches, or by removing starter keys.

8.

DO NOT FORCE TOOL. It will do the job better

and safer at the rate for which it was designed.

9. USE RIGHT TOOL. Do not force tool or

attachment to do a job for which it was not

designed.

10.

WEAR PROPER APPAREL. Do not wear loose

clothing, gloves, neckties, rings, bracelets, or

other jewelry which may get caught in moving

parts. Nonslip footwear is recommended. Wear

protective hair covering to contain long hair.

11. ALWAYS USE SAFETY GLASSES. Also use

face or dust mask if cutting operation is dusty.

Everyday eyeglasses only have impact

resistant lenses, they are NOT safety glasses.

12. SECURE WORK. Use clamps or a vise to hold

work when practical. It's safer than using your

hand and it frees both hands to operate tool.

13. DO NOT OVERREACH. Keep proper footing

and balance at all times.

14. MAINTAIN TOOLS WITH CARE. Keep tools

sharp and clean for best and safest

performance. Follow instructions for

lubricating and changing accessories.

15. DISCONNECT TOOLS before servicing; when

changing accessories such as blades, bits,

cutters, and the like.

16. REDUCE THE RISK OF UNINTENTIONAL

STARTING. Make sure switch is in off position

before plugging in.

17. USE RECOMMENDED ACCESSORIES.

Consult the owner's manual for recommended

accessories. The use of improper accessories

may cause risk of injury to persons.

18. NEVER STAND ON TOOL. Serious injury could

occur if the tool is tipped or if the cutting tool

is unintentionally contacted.

19. CHECK DAMAGED PARTS. Before further use

of the tool, a guard or other part that is

damaged should be carefully checked to

determine that it will operate properly and

perform its intended function - check for

alignment of moving parts, binding of moving

parts, breakage of parts, mounting, and any

other conditions that may affect its operation.

A guard or other part that is damaged should

be properly repaired or replaced.

20. DIRECTION OF FEED. Feed work into a blade

or cutter against the direction of rotation of

the blade or cutter only.

21. NEVER LEAVE TOOL RUNNING UNATTENDED.

TURN POWER OFF. Do not leave tool until it

comes to a complete stop.

22. REPLACEMENT PARTS. When servicing, use

only identical replacement parts.

23. POLARIZED PLUGS. To reduce the risk of

electric shock, this appliance has a polarized

plug (one blade is wider than the other). This

plug will fit in a polarized outlet only one way.

If the plug does not fit fully in the outlet,

reverse the plug. If it still does not fit, contact

a qualified electrician to install the proper

outlet. Do not change the plug in any way.

VOLTAGE WARNING: Before connecting the tool to a

power source (receptacle, outlet, etc.) be sure the

voltage supplied is the same as that specified on the

nameplate of the tool. A power source with voltage

greater than that specified for the tool can result in

SERIOUS INJURY to the user- as well as damage to

the appliance. If in doubt, DO NOT PLUG IN THE

APPLIANCE. Using a power source with voltage less

than the nameplate rating is harmful to the motor.

USE PROPER EXTENSION CORD. Make sure your

extension cord is in good condition. When using an

extension cord, be sure to use one heavy enough to

carry the current your product will draw. An

undersized cord will cause a drop in line voltage

resulting in loss of power and overheating. Table 1

shows the correct size to use depending on cord

length and nameplate ampere rating. If in doubt, use

the next heavier gage. The smaller the gage number,

the heavier the cord.

4

Table 1: Minimum gage for cord

Ampere Rating Volts Total length of cord in feet

120 V 25 ft. 50 ft. 100 ft. 150 ft.

More Than Not More Than AWG

0 6 18 16 16 14

18 16 14 12610

10 12 16 16 14 12

12 16 14 12 Not Recommended

000173

USB036-2

ADDITIONAL SAFETY RULES

DO NOT let comfort or familiarity with product

(gained from repeated use) replace strict adherence

to slide compound saw safety rules. If you use this

tool unsafely or incorrectly, you can suffer serious

personal injury.

1. Wear eye protection.

2. Keep hands out of path of saw blade. Avoid

contact with any coasting blade. It can still

cause severe injury.

3. Do not operate saw without guards in place.

Check blade guard for proper closing before

each use. Do not operate saw if blade guard

does not move freely and close instantly.

Never clamp or tie the blade guard into the

open position.

4. Do not perform any operation freehand. The

workpiece must be secured firmly against the

turn base and guide fence with a vise during

all operations. Never use your hand to secure

the workpiece.

5. Never reach around saw blade.

6.

Turn off tool and wait for saw blade to stop

before moving workpiece or changing settings.

7. Unplug tool before changing blade or

servicing.

8. To reduce the risk of injury, return carriage to

the full rear position after each crosscut

operation.

9. Always secure all moving portions before

carrying the tool.

10. Stopper pin which locks the cutter head down

is for carrying and storage purposes only and

not for any cutting operations.

11. Do not use the tool in the presence of

flammable liquids or gases.

12. Check the blade carefully for cracks or

damage before operation. Replace cracked or

damaged blade immediately. Gum and wood

pitch hardened on blades slows saw and

increases potential for kickback. Keep blade clean

by first removing it from tool, then cleaning it with

gum and pitch remover, hot water or kerosene.

Never use gasoline to clean blade.

13.

While making a slide cut, KICKBACK can occur.

KICKBACK occurs when the blade binds in the

workpiece during a cutting operation and the

saw blade is driven back rapidly towards the

operator. Loss of control and serious personal

injury can result. If blade begins to bind during

a cutting operation, do not continue to cut and

release switch immediately.

14. Use only flanges specified for this tool.

15. Be careful not to damage the arbor, flanges

(especially the installing surface) or bolt.

Damage to these parts could result in blade

breakage.

16.

Make sure that the turn base is properly

secured so it will not move during operation.

Use the holes in the base to fasten the saw to a

stable work platform or bench. NEVER use tool

where operator positioning would be awkward.

17.

For your safety, remove the chips, small pieces,

etc. from the table top before operation.

18. Avoid cutting nails. Inspect for and remove all

nails from the workpiece before operation.

19. Make sure the shaft lock is released before the

switch is turned on.

20. Be sure that the blade does not contact the

turn base in the lowest position.

21. Hold the handle firmly. Be aware that the saw

moves up or down slightly during start-up and

stopping.

22. Make sure the blade is not contacting the

workpiece before the switch is turned on.

23. Before using the tool on an actual workpiece,

let it run for a while. Watch for vibration or

wobbling that could indicate poor installation

or a poorly balanced blade.

24. Wait until the blade attains full speed before

cutting.

25. Stop operation immediately if you notice

anything abnormal.

5

26. Do not attempt to lock the trigger in the "ON"

position.

27. Be alert at all times, especially during

repetitive, monotonous operations. Do not be

lulled into a false sense of security. Blades are

extremely unforgiving.

28. Always use accessories recommended in this

manual. Use of improper accessories such as

abrasive wheels may cause an injury.

29. NEVER hold workpiece on right side of blade

with left hand or vice versa. This is called

cross-armed cutting and exposes user to risk

of SERIOUS PERSONAL INJURY as shown in

the figure. ALWAYS use vise to secure

workpiece.

000030

30. Do not abuse cord. Never yank cord to

disconnect it from the receptacle. Keep cord

away from heat, oil, water and sharp objects.

31. NEVER stack workpieces on the table top to

speed cutting operations. Cut only one piece

at a time.

32. Some material contains chemicals which may

be toxic. Take caution to prevent dust

inhalation and skin contact. Follow material

supplier safety data.

SAVE THESE INSTRUCTIONS.

WARNING:

MISUSE or failure to follow the safety rules stated in

this instruction manual may cause serious personal

injury.

INSTALLATION

Bench mounting

When the tool is shipped, the handle is locked in the

lowered position by the stopper pin. Release the stopper

pin by lowering the handle slightly and pulling the stopper

pin.

1

003923

This tool should be bolted with two bolts to a level and

stable surface using the bolt holes provided in the tool's

base. This will help prevent tipping and possible injury.

1

003924

Turn the adjusting bolt clockwise or counterclockwise so

that it comes into a contact with the floor surface to keep

the tool stable.

1

003925

FUNCTIONAL DESCRIPTION

WARNING:

• Always be sure that the tool is switched off and

unplugged before adjusting or checking function on

the tool.

1. Adjusting bolt

1. Bolt

1. Stopper pin

6

Blade guard

1

002252

When lowering the handle, the blade guard rises

automatically. The guard is spring loaded so it returns to

its original position when the cut is completed and the

handle is raised. NEVER DEFEAT OR REMOVE THE

BLADE GUARD OR THE SPRING WHICH ATTACHES

TO THE GUARD.

In the interest of your personal safety, always maintain

the blade guard in good condition. Any irregular

operation of the blade guard should be corrected

immediately. Check to assure spring loaded return action

of guard. NEVER USE THE TOOL IF THE BLADE

GUARD OR SPRING ARE DAMAGED, FAULTY OR

REMOVED. DOING SO IS HIGHLY DANGEROUS AND

CAN CAUSE SERIOUS PERSONAL INJURY.

If the see-through blade guard becomes dirty, or sawdust

adheres to it in such a way that the blade is no longer

easily visible, unplug the saw and clean the guard

carefully with a damp cloth. Do not use solvents or any

petroleum-based cleaners on the plastic guard.

If the blade guard is especially dirty and vision through

the guard is impaired, use the supplied hex wrench to

loosen the hex socket bolt holding the center cover.

Loosen the hex socket bolt by turning it counterclockwise

and raise the blade guard and center cover. With the

blade guard so positioned, cleaning can be more

completely and efficiently accomplished. When cleaning

is complete, reverse procedure above and secure bolt.

Do not remove spring holding blade guard. If guard

becomes discolored through age or UV light exposure,

contact a Makita service center for a new guard. DO NOT

DEFEAT OR REMOVE GUARD.

1

001782

Positioning kerf board

12

003926

12

3

45

001800

This tool is provided with the kerf boards in the turn base

to minimize tearing on the exit side of a cut. The kerf

boards are factory adjusted so that the saw blade does

not contact the kerf boards. Before use, adjust the kerf

boards as follows:

First, unplug the tool. Loosen all the screws (2 each on

left and right) securing the kerf boards. Re-tighten them

only to the extent that the kerf boards can still be easily

moved by hand. Lower the handle fully and push in the

stopper pin to lock the handle in the lowered position.

Loosen two clamp screws which secure the slide poles.

Pull the carriage toward you fully. Adjust the kerf boards

so that the kerf boards just contact the sides of the blade

teeth. Tighten the front screws (do not tighten firmly).

Push the carriage toward the guide fence fully and adjust

the kerf boards so that the kerf boards just contact the

sides of blade teeth. Tighten the rear screws (do not

tighten firmly).

After adjusting the kerf boards, release the stopper pin

and raise the handle. Then tighten all the screws

securely.

CAUTION:

• Before and after changing the bevel angle, always

adjust the kerf boards as described above.

1. Saw blade

2. Blade teeth

3. Kerf board

4. Left bevel cut

5. Straight cut

1. Thumb screw

2. Kerf board

1. Blade guard

7

Maintaining maximum cutting capacity

1

23

003927

2

3

1

005516

This tool is factory adjusted to provide the maximum

cutting capacity for a 190 mm (7-1/2") saw blade.

When installing a new blade, always check the lower limit

position of the blade and if necessary, adjust it as follows:

First, unplug the tool. Push the carriage toward the guide

fence fully and lower the handle completely. Use the hex

wrench to turn the adjusting bolt until the periphery of the

blade extends slightly below the top surface of the turn

base at the point where the front face of the guide fence

meets the top surface of the turn base.

With the tool unplugged, rotate the blade by hand while

holding the handle all the way down to be sure that the

blade does not contact any part of the lower base.

Re-adjust slightly, if necessary.

WARNING:

• After installing a new blade, always be sure that the

blade does not contact any part of the lower base

when the handle is lowered completely. Always do

this with the tool unplugged.

Stopper arm

1

2

003928

The lower limit position of the blade can be easily

adjusted with the stopper arm. To adjust it, move the

stopper arm in the direction of the arrow as shown in the

figure. Adjust the adjusting screw so that the blade stops

at the desired position when lowering the handle fully.

Adjusting the miter angle

12

345

003929

Loosen the grip by turning counterclockwise. Turn the

turn base while pressing down the lock lever. When you

have moved the grip to the position where the pointer

points to the desired angle on the miter scale, securely

tighten the grip clockwise.

CAUTION:

• When turning the turn base, be sure to raise the

handle fully.

• After changing the miter angle, always secure the

turn base by tightening the grip firmly.

Adjusting the bevel angle

1

2

003930

1

2

3

003931

To adjust the bevel angle, loosen the lever at the rear of

the tool counterclockwise.

Push the handle to the left to tilt the saw blade until the

pointer points to the desired angle on the bevel scale.

Then tighten the lever clockwise firmly to secure the arm.

To tilt the blade to the right, push the release button at the

rear of the tool while tilting the blade slightly to the left

after loosening the lever. With the release button

1. Pointer

2. Bevel scale

3. Arm

1. Lever

2. Release button

1. Turn base

2. Lock lever

3. Miter scale

4. Pointer

5. Grip

1. Adjusting screw

2. Stopper arm

1. Top surface of

turn table

2. Periphery of

blade

3. Guide fence

1. Adjusting bolt

2. Turn base

3. Guide fence

8

depressed, tilt the saw blade to the right.

CAUTION:

• When tilting the saw blade, be sure to raise the

handle fully.

• After changing the bevel angle, always secure the

arm by tightening the lever clockwise.

• When changing bevel angles, be sure to position

the kerf boards appropriately as explained in the

"Positioning kerf boards" section.

Adjusting the lever position

12

003932

The lever can be repositioned at every angle 30° when

the lever does not provide full tightening.

Loosen and remove the screw that secures the lever at

the rear of the tool. Remove the lever and install it again

so that it is slightly above the level. Secure the lever with

the screw firmly.

Switch action

CAUTION:

• Before plugging in the tool, always check to see

that the switch trigger actuates properly and returns

to the "OFF" position when released.

• When not using the tool, remove the lock-off button

and store it in a secure place. This prevents

unauthorized operation.

• Do not pull the switch trigger hard without pressing

in the lock-off button. This can cause switch

breakage.

2

3

1

002253

To prevent the switch trigger from being accidentally

pulled, a lock-off button is provided. To start the tool,

press in the lock-off button and pull the switch trigger.

Release the switch trigger to stop.

WARNING:

• NEVER use tool without a fully operative switch

trigger. Any tool with an inoperative switch is

HIGHLY DANGEROUS and must be repaired

before further usage.

• For your safety, this tool is equipped with a lock-off

button which prevents the tool from unintended

starting. NEVER use the tool if it runs when you

simply pull the switch trigger without pressing the

lock-off button. Return tool to a Makita service

center for proper repairs BEFORE further usage.

• NEVER tape down or defeat purpose and function

of lock-off button.

Electric brake

This tool is equipped with an electric blade brake. If the

tool consistently fails to quickly stop blade after switch

trigger release, have tool serviced at a Makita service

center.

Lighting up the lamps

The blade brake system is not a substitute for blade guard.

NEVER USE TOOL WITHOUT A FUNCTIONING BLADE

GUARD. SERIOUS PERSONAL INJURY CAN RESULT.

For model LS0714FL only

1

2

005518

CAUTION:

• This is not a rainproof light. Do not wash the light in

water or use it in a rain or a wet area. Such a

conduct can cause an electric shock and fume.

• Do not touch the lens of the light, as it is very hot

while it is lighted or shortly after it is turned off. This

may cause a burn to a human body.

• Do not apply impact to the light, which may cause

damage or shorted service time to it.

• Do not keep casting the beam of the light to your

eyes. This can cause your eyes to be hurt.

• Do not cover the light with clothes, carton,

cardboard or similar objects while it is lighted,

which can cause a fire or an ignition.

Push the upper position of the switch for turning on the

light and the lower position for off.

Move the light to shift an area of lighting.

1. Light

2. Light switch

1. Lock-off button

2. Switch trigger

3. Handle

1. Lever

2. Screw

9

NOTE:

• Use a dry cloth to wipe the dirt off the lens of lamp.

Be careful not to scratch the lens of light, or it may

lower the illumination.

Laser beam action

For model LS0714FL only

1

005519

CAUTION:

• Never look into the laser beam. Direct laser beam

may injure your eyes.

To turn on the laser beam, press the upper position (I) of

the switch. Press the lower position (O) to turn off.

Laser line can be shifted to either the left or right side of

the saw blade by adjusting the adjusting screw as follows.

1

005520

1. Loosen the adjusting screw by turning it

counterclockwise.

2. With the adjusting screw loosened, slide the

adjusting screw to the right or left as far as it goes.

3. Tighten the adjusting screw firmly at the position

where it stops sliding.

Laser line is factory adjusted so that it is positioned within

1 mm (0.04") from the side surface of the blade (cutting

position).

NOTE:

• When laser line is dim and almost or entirely

invisible because of the direct sunlight in the indoor

or outdoor window-by work, relocate the work area

to a place not exposed to the direct sunlight.

Aligning the laser line

AB

005521

Laser line can be shifted to either the left or right side of

the blade according to the applications of cutting. Refer

to explanation titled "Laser beam action" regarding its

shifting method.

NOTE:

•

Use wood facing against the guide fence when

aligning the cutting line with the laser line at the side

of guide fence in compound cutting (bevel angle 45

degrees and miter angle right 45 degrees).

A) When you obtain correct size on the left side of

workpiece

• Shift the laser line to the left of the blade.

B) When you obtain correct size on the right side of

workpiece

• Shift the laser line to the right of the blade.

Align the cutting line on your workpiece with the laser line.

ASSEMBLY

WARNING:

•

Always be sure that the tool is switched off and

unplugged before carrying out any work on the tool.

Hex wrench storage

12

012596

The hex wrench is stored as shown in the figure. When

using the hex wrench, pull it out of the wrench holder. After

using the hex wrench, return it to the wrench holder.

1. Wrench holder

2. Hex wrench

1. Adjusting screw

1. Switch for laser

10

Installing or removing saw blade

1

003923

WARNING:

• Always be sure that the tool is switched off and

unplugged before installing or removing the blade.

CAUTION:

• Use only the Makita hex wrench provided to install

or remove the blade. Failure to do so may result in

overtightening or insufficient tightening of the hex

socket bolt. This could cause an injury.

Lock the handle in the raised position by pushing in the

stopper pin.

To remove the blade, use the hex wrench to loosen the

hex socket bolt holding the center cover by turning it

counterclockwise. Raise the blade guard and center

cover.

1

2

3

4

012586

Press the shaft lock to lock the spindle and use the hex

wrench to loosen the hex socket bolt clockwise. Then

remove the hex socket bolt, outer flange and blade.

1

2

3

4

5

012587

To install the blade, mount it carefully onto the spindle,

making sure that the direction of the arrow on the surface

of the blade matches the direction of the arrow on the

blade case. Install the outer flange and hex socket bolt,

and then use the hex wrench to tighten the hex socket

bolt (left-handed) securely counterclockwise while

pressing the shaft lock.

123

45

012717

21 34

002254

Return the blade guard and center cover to its original

position. Then tighten the hex socket bolt clockwise to

secure the center cover. Release the handle from the

raised position by pulling the stopper pin. Lower the

handle to make sure that the blade guard moves properly.

Make sure shaft lock has released spindle before making

cut.

Dust bag (optional accessory)

12

3

003937

The use of the dust bag makes cutting operations clean

and dust collection easy. To attach the dust bag, fit it onto

the dust nozzle.

When the dust bag is about half full, remove the dust bag

from the tool and pull the fastener out. Empty the dust

bag of its contents, tapping it lightly so as to remove

particles adhering to the insides which might hamper

further collection.

NOTE:

If you connect a Makita vacuum cleaner to your saw,

more efficient and cleaner operations can be performed.

1. Dust bag

2. Dust nozzle

3. Fastener

1. Blade case

2. Arrow

3. Saw blade

4. Arrow

1. Outer flange

2. Saw blade

3. Inner flange

4. Hex socket bolt

(left-handed)

5. Spindle

1. Shaft lock

2. Arrow

3. Blade case

4. Hex wrench

5. Hex socket bolt

1. Center cover

2. Hex socket bolt

3. Hex wrench

4. Safety cover

1. Stopper pin

11

Dust box (Optional accessory)

1

2

3

006793

Insert the dust box into the dust nozzle.

Empty the dust box at the earliest possible.

To empty the dust box, open the cover by pushing the

button and throw away sawdust. Return the cover to the

original position and it locks. Dust box can easily be

removed by pulling out while turning it near the dust

nozzle on the tool.

NOTE:

• If you connect a Makita vacuum cleaner to this tool,

more efficient and cleaner operations can be

performed.

CAUTION:

• Empty the dust box before collected sawdust level

reaches the cylinder part.

1

23

006792

1

2

006794

Securing workpiece

WARNING:

• It is extremely important to always secure the

workpiece properly and tightly with the vise. Failure

to do so can cause the tool to be damaged and/or

the workpiece to be destroyed. PERSONAL

INJURY MAY ALSO RESULT. Also, after a cutting

operation, DO NOT raise the blade until the blade

has come to a complete stop.

CAUTION:

• When cutting long workpieces, use supports that

are as high as the top surface level of the turn base.

Do not rely solely on the vertical vise and/or

horizontal vise to secure the workpiece.

Thin material tends to sag. Support workpiece over

its entire length to avoid blade pinch and possible

KICKBACK.

12

001549

Vertical vise

2

7

4

5

3

1

6

002255

The vertical vise can be installed in two positions on

either the left or right side of the guide fence or the holder

assembly (optional accessory). Insert the vise rod into

the hole in the guide fence or the holder assembly and

tighten the screw to secure the vise rod.

Position the vise arm according to the thickness and

shape of the workpiece and secure the vise arm by

tightening the screw. If the screw to secure the vise arm

contacts the guide fence, install the screw on the

opposite side of vise arm. Make sure that no part of the

tool contacts the vise when lowering the handle fully and

pulling or pushing the carriage all the way. If some part

contacts the vise, re-position the vise.

Press the workpiece flat against the guide fence and the

turn base. Position the workpiece at the desired cutting

position and secure it firmly by tightening the vise knob.

CAUTION:

• The workpiece must be secured firmly against the

turn base and guide fence with the vise during all

operations.

1. Vise arm

2. Vise rod

3. Guide fence

4. Holder

5. Holder

assembly

6. Vise knob

7. Screw

1. Support

2. Turn base

1. Cylinder part

2. Dust box

1. Cylinder part

2. Dust box

3. Sawdust

1. Dust box

2. Cover

3. Button

12

Horizontal vise (optional accessory)

12

3

4

001807

The horizontal vise can be installed on the left side of the

base. By turning the vise knob counterclockwise, the

screw is released and the vise shaft can be moved

rapidly in and out. By turning the vise knob clockwise, the

screw remains secured. To grip the workpiece, turn the

vise knob gently clockwise until the projection reaches its

topmost position, then fasten securely. If the vise knob is

forced in or pulled out while being turned clockwise, the

projection may stop at an angle. In this case, turn the vise

knob back counterclockwise until the screw is released,

before turning again gently clockwise.

The maximum width of the workpiece which can be

secured by the horizontal vise is 120 mm (4-3/4").

CAUTION:

• Grip the workpiece only when the projection is at

the topmost position. Failure to do so may result in

insufficient securing of the workpiece. This could

cause the workpiece to be thrown, cause damage

to the blade or cause the loss of control, which can

result in PERSONAL INJURY.

Holders and holder assembly

(optional accessories)

12

002247

The holders and the holder assembly can be installed on

either side as a convenient means of supporting

workpieces horizontally. Install them as shown in the

figure. Then tighten the screws firmly to secure the

holders and the holder assembly.

When cutting long workpieces, use the holder-rod

assembly (optional accessory). It consists of two holder

assemblies and two rods 12.

2

1

002246

CAUTION:

• Always support long workpieces level with the top

surface of the turn base for accurate cuts and to

prevent dangerous loss of control of the tool.

OPERATION

CAUTION:

• Before use, be sure to release the handle from the

lowered position by pulling the stopper pin.

• Make sure the blade is not contacting the

workpiece, etc. before the switch is turned on.

• Do not apply excessive pressure on the handle

when cutting. Too much force may result in

overload of the motor and/or decreased cutting

efficiency. Push down handle with only as much

force as is necessary for smooth cutting and

without significant decrease in blade speed.

• Gently press down the handle to perform the cut. If

the handle is pressed down with force or if lateral

force is applied, the blade will vibrate and leave a

mark (saw mark) in the workpiece and the precision

of the cut will be impaired.

• During a slide cut, gently push the carriage toward

the guide fence without stopping. If the carriage

movement is stopped during the cut, a mark will be

left in the workpiece and the precision of the cut will

be impaired.

1. Press cutting (cutting small workpieces)

1

002202

Workpieces up to 50 mm (2") high and 97 mm

(3-13/16") wide can be cut in the following way.

Push the carriage toward the guide fence fully and

tighten two clamp screws which secure the slide

poles clockwise to secure the carriage. Secure the

1. Clamp screw

1. Holder

assembly

2. Rod 12

1. Holder

2. Holder

assembly

1. Vise knob

2. Projection

3. Vise shaft

4. Base

13

workpiece with the vise. Switch on the tool without

the blade making any contact and wait until the

blade attains full speed before lowering. Then

gently lower the handle to the fully lowered position

to cut the workpiece. When the cut is completed,

switch off the tool and WAIT UNTIL THE BLADE

HAS COME TO A COMPLETE STOP before

returning the blade to its fully elevated position.

CAUTION:

• Firmly tighten two clamping screws which secure

the slide poles clockwise so that the carriage will

not move during operation. Insufficient tightening

may cause unexpected kickback of the blade.

Possible serious PERSONAL INJURY may result.

2. Slide (push) cutting (cutting wide workpieces)

002203

Loosen two clamp screws which secure the slide

poles counterclockwise so that the carriage can

slide freely. Secure the workpiece with the vise. Pull

the carriage toward you fully. Switch on the tool

without the blade making any contact and wait until

the blade attains full speed. Press down the handle

and PUSH THE CARRIAGE TOWARD THE

GUIDE FENCE AND THROUGH THE

WORKPIECE. When the cut is completed, switch

off the tool and WAIT UNTIL THE BLADE HAS

COME TO A COMPLETE STOP before returning

the blade to its fully elevated position.

CAUTION:

• Whenever performing the slide cut, FIRST PULL

THE CARRIAGE TOWARD YOU FULLY and press

down the handle to the fully lowered position, then

PUSH THE CARRIAGE TOWARD THE GUIDE

FENCE. NEVER START THE CUT WITH THE

CARRIAGE NOT FULLY PULLED TOWARD YOU.

If you perform the slide cut without pulling the

carriage fully or if you perform the slide cut toward

your direction, the blade may kickback

unexpectedly with the potential to cause serious

PERSONAL INJURY.

• Never perform the slide cut with the handle locked

in the lowered position by pressing the stopper pin.

• Never loosen the clamp screw which secures the

carriage while the blade is rotating. This may cause

serious injury.

3. Miter cutting

Refer to the previously covered "Adjusting the miter

angle".

4. Bevel cut

002204

Loosen the lever and tilt the saw blade to set the

bevel angle (Refer to the previously covered

"Adjusting the bevel angle"). Be sure to retighten

the lever firmly to secure the selected bevel angle

safely. Secure the workpiece with a vise. Make sure

the carriage is pulled all the way back toward the

operator. Switch on the tool without the blade

making any contact and wait until the blade attains

full speed. Then gently lower the handle to the fully

lowered position while applying pressure in parallel

with the blade and PUSH THE CARRIAGE

TOWARD THE GUIDE FENCE TO CUT THE

WORKPIECE. When the cut is completed, switch

off the tool and WAIT UNTIL THE BLADE HAS

COME TO A COMPLETE STOP before returning

the blade to its fully elevated position.

CAUTION:

• Always be sure that the blade will move down to

bevel direction during a bevel cut. Keep hands out

of path of saw blade.

• During a bevel cut, it may create a condition

whereby the piece cut off will come to rest against

the side of the blade. If the blade is raised while the

blade is still rotating, this piece may be caught by

the blade, causing fragments to be scattered which

is dangerous. The blade should be raised ONLY

after the blade has come to a complete stop.

• When pressing the handle down, apply pressure

parallel to the blade. If the pressure is not parallel to

the blade during a cut, the angle of the blade might

be shifted and the precision of the cut will be

impaired.

5. Compound cutting

Compound cutting is the process in which a bevel

angle is made at the same time in which a miter

14

angle is being cut on a workpiece. Compound

cutting can be performed at angle shown in the

table.

Miter angle

Left and Right 45

Right 50

Right 55

Right 57

Bevel angle

Left 0 - 45

Left 0 - 40

Left 0 - 30

Left 0 - 25

006393

When performing compound cutting, refer to "Press

cutting", "Slide cutting", "Miter cutting" and "Bevel

cut" explanations.

6. Cutting crown and cove moldings

Crown and cove moldings can be cut on a

compound miter saw with the moldings laid flat on

the turn base.

There are two common types of crown moldings

and one type of cove moldings; 52/38° wall angle

crown molding, 45° wall angle crown molding and

45° wall angle cove molding. See illustrations.

123

001555

There are crown and cove molding joints which are

made to fit "Inside" 90° corners ((1) and (2) in Fig.

A) and "Outside" 90° corners ((3) and (4) in Fig. A).

(1) (2) (3)(4)

1 2

Fig.A

001556

2

(1)

(2)

(1)

(2) (2)

(1)

(2)

(1)

(2)

(3)(4)

1

001557

Measuring

Measure the wall length and adjust workpiece on

table to cut wall contact edge to desired length.

Always make sure that cut workpiece length

at the

back of the workpiece

is the same as wall length.

Adjust cut length for angle of cut. Always use several

pieces for test cuts to check the saw angles.

When cutting crown and cove moldings, set the

bevel angle and miter angle as indicated in the table

(A) and position the moldings on the top surface of

the saw base as indicated in the table (B).

In the case of left bevel cut

Molding

position in

Fig. A

Bevel angleMiter angle

For outside

corner

For inside

corner

52/38° type45° type

Right 31.6°

45° type

Left 33.9° Left 30°

52/38° type

Left 31.6° Left 35.3°

Right 35.3°

Right 35.3°Right 31.6°

(1)

(2)

(3)

(4)

Table (A)

006361

Molding

position in

Fig. A

Molding edge against

guide fence

(1) Ceiling contact edge should

be against guide fence.

Ceiling contact edge should

be against guide fence.

For

outside

corner

Finished piece

will be on the

Left side of

blade.

Finished piece

will be on the

Right side of

blade.

For inside

corner

Wall contact edge should be

against guide fence.

Finished piece

(2)

(3)

(4)

Table (B)

006362

Example:

In the case of cutting 52/38° type crown

molding for position (1) in Fig. A:

• Tilt and secure bevel angle setting to

33.9° LEFT.

• Adjust and secure miter angle setting to

31.6° RIGHT.

• Lay crown molding with its broad back

(hidden) surface down on the turn base

with its CEILING CONTACT EDGE

against the guide fence on the saw.

• The finished piece to be used will

always be on the LEFT side of the blade

after the cut has been made.

1. Inside corner

2. Outside corner

1. Inside corner

2. Outside corner

1. 52/38 ﾟ type

crown molding

2. 45 ﾟ type crown

molding

3. 45 ﾟ type cove

molding

15

In the case of right bevel cut

Molding

position in

Fig. A

Bevel angleMiter angle

For outside

corner

For inside

corner

52/38° type45° type

Right 31.6°

45° type

Right 33.9° Right 30°

52/38° type

Left 31.6° Left 35.3°

Right 35.3°

Right 35.3°Right 31.6°

(1)

(2)

(3)

(4)

Table (A)

006363

Molding

position in

Fig. A

Molding edge against

guide fence

(1)

For

outside

corner

For inside

corner

Finished piece

(2)

(3)

(4)

Table (B)

Finished piece

will be on the

Left side of

blade.

Finished piece

will be on the

Right side of

blade.

Wall contact edge should be

against guide fence.

Wall contact edge should be

against guide fence.

Ceiling contact edge should

be against guide fence.

006364

Example:

In the case of cutting 52/38° type crown

molding for position (1) in Fig. A:

• Tilt and secure bevel angle setting to

33.9° RIGHT.

• Adjust and secure miter angle setting to

31.6° RIGHT.

• Lay crown molding with its broad back

(hidden) surface down on the turn base

with its WALL CONTACT EDGE against

the guide fence on the saw.

• The finished piece to be used will

always be on the RIGHT side of the

blade after the cut has been made.

16

52°

38°

Ceiling

Wall

30.1

29.7

29.4

29.0

28.7

28.3

28.0

27.6

27.2

26.9

26.5

26.1

25.8

25.4

25.0

24.7

24.3

23.9

23.6

23.2

22.8

22.5

22.1

21.7

21.3

21.0

20.6

20.2

19.8

19.5

19.1

18.7

18.3

17.9

17.6

17.2

16.8

16.4

16.0

15.6

26.9

26.5

26.1

25.7

25.3

24.9

24.5

24.1

23.7

23.3

22.9

22.6

22.2

21.8

21.4

21.0

20.7

20.3

19.9

19.6

19.2

18.8

18.5

18.1

17.8

17.4

17.1

16.7

16.4

16.0

15.7

15.3

15.0

14.6

14.3

14.0

13.6

13.3

13.0

12.8

101

102

103

104

105

106

107

108

109

110

111

112

113

114

115

116

117

118

119

120

121

122

123

124

125

126

127

128

129

130

131

132

133

134

135

136

137

138

139

140

15.3

14.9

14.5

14.1

13.7

13.3

12.9

12.5

12.2

11.8

11.4

11.0

10.8

10.2

9.8

9.4

9.0

8.6

8.3

7.9

7.5

7.1

6.7

6.3

5.9

5.5

5.1

4.7

4.3

3.9

3.5

3.2

2.8

2.4

2.0

1.6

1.2

0.8

0.4

0.0

12.3

12.0

11.6

11.3

11.0

10.7

10.3

10.0

9.7

9.4

9.0

8.7

8.4

8.1

7.8

7.5

7.1

6.8

6.5

6.2

5.9

5.6

5.3

4.9

4.6

4.3

4.0

3.7

3.4

3.1

2.8

2.5

2.2

1.8

1.5

1.2

0.9

0.6

0.3

0.0

141

142

143

144

145

146

147

148

149

150

151

152

153

154

155

156

157

158

159

160

161

162

163

164

165

166

167

168

169

170

171

172

173

174

175

176

177

178

179

180

Wall to Crown Molding Angle: 52/38 degrees

Compound Miter Saw

Miter and Bevel Angle Settings

000031

Wall Angle

(deg.)

Bevel Angle

(deg.)

Miter Angle

(deg.)

Wall Angle

(deg.)

Bevel Angle

(deg.)

Miter Angle

(deg.)

43.0

42.8

42.5

42.2

41.9

41.7

41.4

41.1

40.8

40.5

40.2

39.9

39.6

39.3

39.0

38.7

38.4

38.1

37.8

37.4

37.1

36.8

36.5

36.2

35.8

35.5

35.2

34.9

34.5

34.2

33.9

33.5

33.2

32.8

32.5

32.2

31.8

31.5

31.1

30.8

30.4

46.8

46.3

45.7

45.1

44.6

44.0

43.5

42.9

42.4

41.9

41.3

40.8

40.3

39.8

39.2

38.7

38.2

37.7

37.2

36.8

36.3

35.8

35.3

34.8

34.4

33.9

33.4

33.0

32.5

32.1

31.6

31.2

30.7

30.3

29.9

29.4

29.0

28.6

28.2

27.7

27.3

60

61

62

63

64

65

66

67

68

69

70

71

72

73

74

75

76

77

78

79

80

81

82

83

84

85

86

87

88

89

90

91

92

93

94

95

96

97

98

99

100

Wall Angle

(deg.)

Bevel Angle

(deg.)

Miter Angle

(deg.)

EN0002-1

17

26.7

26.4

26.1

25.8

25.5

25.2

24.9

24.6

24.2

23.9

23.6

23.3

23.0

22.7

22.3

22.0

21.7

21.4

21.0

20.7

20.4

20.0

19.7

19.4

19.1

18.7

18.4

18.1

17.7

17.4

17.1

16.7

16.4

16.0

15.7

15.4

15.0

14.7

14.3

14.0

30.2

29.8

29.4

28.9

28.5

28.1

27.6

27.2

26.8

26.3

25.9

25.5

25.1

24.7

24.3

23.8

23.4

23.0

22.6

22.2

21.8

21.4

21.0

20.6

20.2

19.8

19.4

19.0

18.6

18.2

17.9

17.5

17.1

16.7

16.3

15.9

15.6

15.2

14.8

14.4

101

102

103

104

105

106

107

108

109

110

111

112

113

114

115

116

117

118

119

120

121

122

123

124

125

126

127

128

129

130

131

132

133

134

135

136

137

138

139

140

13.7

13.3

13.0

12.6

12.3

11.9

11.6

11.2

10.9

10.5

10.2

9.8

9.5

9.2

8.8

8.5

8.1

7.8

7.4

7.1

6.7

6.4

6.0

5.6

5.3

4.9

4.6

4.2

3.9

3.5

3.2

2.8

2.5

2.1

1.8

1.4

1.1

0.7

0.4

0.0

14.1

13.7

13.3

12.9

12.6

12.2

11.8

11.5

11.1

10.7

10.4

10.0

9.6

9.3

8.9

8.5

8.2

7.8

7.5

7.1

6.7

6.4

6.0

5.7

5.3

5.0

4.6

4.3

3.9

3.5

3.2

2.8

2.5

2.1

1.8

1.4

1.1

0.7

0.4

0.0

141

142

143

144

145

146

147

148

149

150

151

152

153

154

155

156

157

158

159

160

161

162

163

164

165

166

167

168

169

170

171

172

173

174

175

176

177

178

179

180

Wall to Crown Molding Angle: 45 degrees

Compound Miter Saw

Miter and Bevel Angle Settings

000032

Wall Angle

(deg.)

Bevel Angle

(deg.)

Miter Angle

(deg.)

Wall Angle

(deg.)

Bevel Angle

(deg.)

Miter Angle

(deg.)

37.8

37.5

37.3

37.1

36.8

36.6

36.4

36.1

35.9

35.6

35.4

35.1

34.9

34.6

34.4

34.1

33.9

33.6

33.3

33.1

32.8

32.5

32.3

32.0

31.7

31.4

31.1

30.9

30.6

30.3

30.0

29.7

29.4

29.1

28.8

28.5

28.2

27.9

27.6

27.3

27.0

50.8

50.2

49.6

49.1

48.5

48.0

47.4

46.9

46.4

45.8

45.3

44.8

44.2

43.7

43.2

42.7

42.1

41.6

41.1

40.6

40.1

39.6

39.1

38.6

38.1

37.7

37.2

36.7

36.2

35.7

35.3

34.8

34.3

33.9

33.4

32.9

32.5

32.0

31.6

31.1

30.7

60

61

62

63

64

65

66

67

68

69

70

71

72

73

74

75

76

77

78

79

80

81

82

83

84

85

86

87

88

89

90

91

92

93

94

95

96

97

98

99

100

Wall Angle

(deg.)

Bevel Angle

(deg.)

Miter Angle

(deg.)

45°

Ceiling

Wall

EN0003-1

18

7. Cutting aluminum extrusion

1

2

3

4

5

001844

When securing aluminum extrusions, use spacer

blocks or pieces of scrap as shown in the figure to

prevent deformation of the aluminum. Use a cutting

lubricant when cutting the aluminum extrusion to

prevent build-up of the aluminum material on the

blade.

CAUTION:

• Never attempt to cut thick or round aluminum

extrusions. Thick aluminum extrusions may come

loose during operation and round aluminum

extrusions cannot be secured firmly with this tool.

8. Wood facing

Use of wood facing helps to assure splinter-free

cuts in workpieces. Attach a wood facing to the

guide fence using the holes in the guide fence.

See the figure concerning the dimensions for a

suggested wood facing.

Over 15mm (5/8")Over 420mm (16-1/2")

11

50mm-60mm

(2"-2-3/8")

27mm (1-1/16")

85mm

(3-3/8")

70mm

(2-3/4")

85mm

(3-3/8")

70mm

(2-3/4")

002206

CAUTION:

• Use straight wood of even thickness as the wood

facing.

• Use screws to attach the wood facing to the guide

fence. The screws should be installed so that the

screw heads are below the surface of the wood

facing.

• When the wood facing is attached, do not turn the

turn base with the handle lowered. The blade

and/or the wood facing will be damaged.

9. Cutting repetitive lengths

1

2

3

001846

When cutting several pieces of stock to the same

length, ranging from 220 mm (8-5/8") to 385 mm

(15-1/8"), use of the set plate (optional accessory)

will facilitate more efficient operation. Install the set

plate on the holder (optional accessory) as shown

in the figure.

Align the cutting line on your workpiece with either

the left or right side of the groove in the kerf board,

and while holding the workpiece from moving,

move the set plate flush against the end of the

workpiece. Then secure the set plate with the screw.

When the set plate is not used, loosen the screw

and turn the set plate out of the way.

NOTE:

• Use of the holder-rod assembly (optional

accessory) allows cutting repetitive lengths up to

2,200 mm (7.2ft) approximately.

10. Groove cutting

1

001563

A dado type cut can be made by proceeding as

follows:

Adjust the lower limit position of the blade using the

adjusting screw and the stopper arm to limit the

cutting depth of the blade. Refer to "Stopper arm"

section described on previously.

After adjusting the lower limit position of the blade,

cut parallel grooves across the width of the

workpiece using a slide (push) cut as shown in the

figure. Then remove the workpiece material

between the grooves with a chisel. Do not attempt

to perform this type of cut using wide (thick) blades

or with a dado blade. Possible loss of control and

injury may result.

1. Cut grooves with

blade

1. Set plate

2. Holder

3. Screw

1. Vise

2. Spacer block

3. Guide fence

4. Aluminum

extrusion

5. Spacer block

1. Holes

19

CAUTION:

•

Be sure to return the stopper arm to the original

position when performing other than groove cutting.

Carrying tool

1

003923

012607

Make sure that the tool is unplugged. Secure the blade at

0° bevel angle and the turn base at the full right miter

angle position. Secure the slide poles so that the lower

slide pole is locked in the position of the carriage fully

pulled to operator and the upper poles are locked in the

position of the carriage fully pushed forward to the guide

fence. Lower the handle fully and lock it in the lowered

position by pushing in the stopper pin.

Carry the tool by holding both sides of the tool base as

shown in the figure. If you remove the holders, dust bag,

etc., you can carry the tool more easily.

CAUTION:

• Always secure all moving portions before carrying

the tool.

• Stopper pin is for carrying and storage purposes

only and not for any cutting operations.

MAINTENANCE

CAUTION:

• Always be sure that the tool is switched off and

unplugged before attempting to perform inspection

or maintenance.

• Never use gasoline, benzine, thinner, alcohol or the

like. Discoloration, deformation or cracks may

result.

WARNING:

• Always be sure that the blade is sharp and clean for

the best and safest performance.

Adjusting the cutting angle

This tool is carefully adjusted and aligned at the factory,

but rough handling may have affected the alignment. If

your tool is not aligned properly, perform the following:

1. Miter angle

12

012585

Push the carriage toward the guide fence and

tighten two clamp screws to secure the carriage.

Loosen the grip which secures the turn base. Turn

the turn base so that the pointer points to 0° on the

miter scale. Then turn the turn base slightly

clockwise and counterclockwise to seat the turn

base in the 0° miter notch. (Leave as it is if the

pointer does not point to 0°.) Loosen the hex socket

bolt securing the guide fence using the hex wrench.

Lower the handle fully and lock it in the lowered

position by pushing in the stopper pin. Square the

side of the blade with the face of the guide fence

using a triangular rule, try-square, etc. Then

securely tighten the hex socket bolt on the guide

fence in the order from the right side.

1

002209

Make sure that the pointer points to 0° on the miter

scale. If the pointer does not point to 0°, loosen the

screw which secures the pointer and adjust the

pointer so that it will point to 0°.

1. Triangular rule

1. Guide fence

2. Hex socket bolt

1. Stopper pin

20

1

23

003942

2. Bevel angle

(1) 0° bevel angle

Push the carriage toward the guide fence and

tighten two clamp screws to secure the

carriage. Lower the handle fully and lock it in

the lowered position by pushing in the stopper

pin. Loosen the lever at the rear of the tool.

Turn the 0° bevel angle adjusting bolt (lower

bolt) on the right side of the arm two or three

revolutions counterclockwise to tilt the blade

to the right.

2

1

5

4

3

012589

Carefully square the side of the blade with the

top surface of the turn base using the

triangular rule, try-square, etc. by turning the

0° bevel angle adjusting bolt clockwise. Then

tighten the lever securely.

1

2

3

001819

Make sure that the pointer on the arm point to

0° on the bevel scale on the arm holder. If it

does not point to 0°, loosen the screw which

secures the pointer and adjust the pointer so

that it will point to 0°.

123

003944

(2) 45° bevel angle

1

012590

Adjust the 45° bevel angle only after

performing 0° bevel angle adjustment. To

adjust left 45° bevel angle, loosen the lever

and tilt the blade to the left fully. Make sure that

the pointer on the arm points to 45° on the

bevel scale on the arm holder. If the pointer

does not point to 45°, turn the 45° bevel angle

adjusting bolt (upper bolt) on the right side of

the arm until the pointer points to 45°.

Adjusting the position of laser line

For model LS0714FL only

1

2

3

005701

1

2

005702

WARNING:

• As the tool is plugged when adjusting the position

of laser line, take a full caution especially at switch

1. Vertical vise

2. Holder

assembly

(optional

accessory)

1. Workpiece

2. Cutting line

3. Holder

assembly

(optional

accessory)

1. Left 45 ﾟ bevel

angle adjusting

bolt

1. Bevel scale

2. Pointer

3. Screw

1. Triangular rule

2. Saw blade

3. Top surface of

turn table

1. Lever

2. Arm holder

3. 0 ﾟ degree

bevel angle

adjusting bolt

4. Arm

5. Release button

1. Screw

2. Miter scale

3. Pointer

La page charge ...

Makita LS0714FL Manuel utilisateur

Makita LS0714FL Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents