Chief CMA362 Guide d'installation
- Catégorie
- Accessoires pour écran plat
- Taper
- Guide d'installation
INSTALLATION INSTRUCTIONS
C-Clamp Adapter
CMA362
CMA362 Installation Instructions
2
DISCLAIMER
Milestone AV Technologies, and its affiliated corporations and
subsidiaries (collectively, "Milestone"), intend to make this
manual accurate and complete. However, Milestone makes no
claim that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Milestone
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Milestone assumes
no responsibility for accuracy, completeness or sufficiency of
the information contained in this document.
Chief® is a registered trademark of Milestone AV Technologies.
All rights reserved.
IMPORTANT SAFETY INSTRUCTIONS!
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all components are
properly assembled and installed using the instructions
provided.
WARNING: Failure to provide adequate structural strength
for this component can result in serious personal injury or
damage to equipment! It is the installer’s responsibility to
make sure the structure to which this component is attached
can support five times the combined weight of all equipment.
Reinforce the structure as required before installing the
component.
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components attached to the CMA362 does not exceed
250 lbs (113.3 kg).
•The weight capacity of the CMA362 may be LIMITED
to the lowest weight capacity of any other component
or accessory used within the mounting system.
WARNING: Use this mounting system only for its intended
use as described in these instructions. Do not use
attachments not recommended by the manufacturer.
WARNING: Never operate this mounting system if it is
damaged. Return the mounting system to a service center for
examination and repair.
WARNING: Do not use this product outdoors.
IMPORTANT ! :
The CMA362 is designed to be mounted:
• to a 1" steel pipe;
• to a 1-5/8” wide Unistrut ceiling channel,
spanning a maximum of 4 feet. The total
combined weight of all components CANNOT
exceed the allowable load of the channel! (Refer
to Unistrut instructions for further details.)
• to a 2"x4" wood joist;
--SAVE THESE INSTRUCTIONS--
Installation Instructions CMA362
3
DIMENSIONS
DIMENSIONS: [MILLIMETERS]
INCHES
CMA362 Installation Instructions
4
LEGEND
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Measure
Medir
Messen
Medir
Misurare
Meten
Mesurer
Phillips Screwdriver
Destornillador Phillips
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
By Hand
A mano
Von Hand
Com a mão
A mano
Met de hand
À la main
Target of Projector
Punto de enfoque del proyector
Ziel des Projektors
Mira do projector
Punto di proiezione
Doel van de projector
Cible du projecteur
Hammer
Martillo
Hammer
Martelo
Martello
Hamer
Marteau
Pencil Mark
Marcar con lápiz
Stiftmarkierung
Marcar com lápis
Segno a matita
Potloodmerkteken
Marquage au crayon
Drill Hole
Perforar
Bohrloch
Fazer furo
Praticare un foro
Gat boren
Percez un trou
Adjust
Ajustar
Einstellen
Ajustar
Regolare
Afstellen
Ajuster
Optional
Opcional
Optional
Opcional
Opzionale
Optie
En option
Security Wrench
Llave de seguridad
Sicherheitsschlüssel
Chave de segurança
Chiave di sicurezza
Veiligheidssleutel
Clé de sécurité
Open-Ended Wrench
Llave de boca
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Clé à fourche
Installation Instructions CMA362
5
TOOLS REQUIRED FOR INSTALLATION
PARTS
#2
3/32"
(included)
9/16"
9/16"
(3/8")
F (2)
C (1)
G (1)
(3/8"-16 x 4-1/2")
B (1)
(10-24 x 1/4")
(3/32")
A (1)
[CMA362 assembly]
D (2) E (1)
(3/8"-16 x 5") (3/8")
CMA362 Installation Instructions
6
INSTALLATION
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components attached to the CMA362 does not exceed
250 lbs (113.3 kg).
The CMA362 is designed to fit a 1" steel pipe, a 1-5/8” wide
Unistrut ceiling channel spanning a maximum of 4 feet, or a
2"x4" wood joist.
The CMA362 includes an opening for a 1-1/2" NPT or NPSM
following ANSI/ASME B1.20.1 (Schedule 40, 0.154" minimum
thickness steel or aluminum - ASTM B221) threaded extension
column (not included) which must be installed into the CMA362
with a minimum of four threads engaged.
IMPORTANT ! : These installation instructions assume
that a 1" steel pipe, a 1-5/8” wide Unistrut ceiling channel
spanning a maximum of 4 feet, or 2"x4" wood joist has
been properly installed and is in place.
Assembly and Installation
1. Place CMA362 assembly (A) on desired mounting
structure. (See Figure 1)
Figure 1
2. Install and tighten two 3/8-16 x 5" hex head cap screws (D)
and two 3/8" Nylock nuts (F) to fasten CMA362 to mounting
structure. (See Figure 1)
3. Install 3/8" hex nut (E) to 3/8-16 x 4-1/2" hex head tap bolt
(C). (See Figure 2)
Figure 2
4. Insert 3/8-16 x 4-1/2" hex head tap bolt (C) through hole on
the CMA362 (A). (See Figure 3)
Figure 3
(D) x 2
(A)
2
Mounting
structure
(F)
(F) x 2
(C) x 1
(E) x 1
3
(C) x 1
(E) x 1
4
(A)
NOTE:
shown for clarity.
Mounting structure not
Installation Instructions CMA362
7
NOTE: The 3/8-16 hex nut (E) remains outside hole. (See
Figure 4)
Figure 4
5. Tighten 3/8"-16 x 4-1/2" hex head tap bolt (C) against
mounting structure, using the 3/8-16 hex nut (E) as a jam
nut to secure the bolt in place. (See Figure 5)
Figure 5
6. Install 1-1/2" extension column (not included) with a
minimum of four threads engaged.
7. Secure extension column using 10-24 x 1/4" set screw (B).
(See Figure 6)
Figure 6
(C) x 1
(E) x 1
NOTE:
not shown for clarity.
Mounting structure
(E)
5
Mounting
(A)
(C)
structure
(B) x 1
(A)
7
Mounting structure
Extension column
(not included)
CMA362 Installation Instructions
Chief Manufacturing, a products division
of Milestone AV Technologies
8800-002488 Rev00
2013 Milestone AV Technologies, a
Duchossois Group Company
www.chiefmfg.com
10/13
USA/International A 6436 City West Parkway, Eden Prairie, MN 55344
P800.582.6480 / 952.225.6000
F877.894.6918 / 952.894.6918
Europe A Franklinstraat 14, 6003 DK Weert, Netherlands
P+31 (0) 495 580 852
F+31 (0) 495 580 845
Asia Pacific A Office No. 1 on 12/F, Shatin Galleria
18-24 Shan Mei Street
Fotan, Shatin, Hong Kong
P852 2145 4099
F852 2145 4477
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
Chief CMA362 Guide d'installation
- Catégorie
- Accessoires pour écran plat
- Taper
- Guide d'installation
dans d''autres langues
- English: Chief CMA362 Installation guide