Edwards Signaling 1509 Series Guide d'installation

Marque: Edwards Signaling

Modèle: 1509 Series

Taper: Guide d'installation

Ce manuel convient également à

1509

Installation Instructions for Flush Wall Mount Electromagnetic Door

Holders Catalog Series 1509

501-152800-0-01

Description

The 1509 Series are flush mount door holders for use with single

doors. The units are UL and cUL Listed and FM approved

Installation

Install and wire in accordance with applicable codes, standards,

such as NFPA publications 70 (National Electrical Code), 72 (Na-

tional Fire Alarm Code), and 80 (Standard for Fire Doors and Fire

Windows), and/or other regulations applicable to the country

and locality of installation and in accordance with authorities

having jurisdiction.

1. Using Figure 1 and Table 2, locate the intersection of

Dimension X and Dimension Y. Dimension Z is shown at the

intersection in the gray area.

NOTE: If dimension X or Y is not shown on the chart,

extrapolate Dimension Z. (i.e., if X=7, and Y=28,

Z = (27-5/8 - ((27-5/8 - 27-1/4)/2) => Z = 27-9/16"

2. Install a single gang outlet box (not supplied) on the

horizontal center line and 5" from the top of the door.

NOTE: The outlet box must be able to withstand a maximum

holding force of 50 pounds.

If X and Y intersect in the blank area in Table 2, DO NOT

install the outlet box. The contact plate and electromagnet

cannot be aligned with these dimensions.

Door

Door jamb

Wall line

Outlet box

center

line

Figure 1. Locating the Door Holder

Table 2. Dimension chart (in inches)

Table 1. Specifications

Cat. No. Volts Amps

1509-E1 12V DC 0.170

1509-E5 12V AC 60 Hz 0.150

1509-AQN5 24V AC 60 Hz 0.015

24V DC 0.015

120V AC 60 Hz 0.015

Electromagnet Assembly and Cover Mounting

WARNING

To prevent electrical shock, ensure power is discon-

nected.

1. Refer to Figure 2. Pull field wiring through conduit into the

single gang outlet box.

2. Establish earth-ground continuity in accordance with

applicable codes, standards and authorities having

jurisdiction. A green insulated lead wire is provided on -

AQN5 models for this purpose.

3 For -E1 and -E5 models, connect the field power wiring to the

electromagnet assembly wiring leads.

For -AQN5 models, refer to Figure 3 and connect as

instructed below:

a. 120V AC operation. Connect power field wiring to

terminals marked "120V AC" and "COM."

b. 24V AC/DC operation. Connect power field wiring to

terminals marked "24V AC/DC" and "COM."

4. Secure the electromagnet bracket assembly to the outlet box

using two #6-32 x 1/2" screws provided (Figure 2).

5. Mount the cover to the electromagnetic bracket assembly

and secure with the two #6-32 x 3/8" screws provided

(Figure 2).

NOTE: The combined projection of the electromagnet

assembly and armature assembly is 1 27/32".

Armature Assembly Mounting

NOTE: Armature assembly must be mounted vertically

(Figure 4) to obtain correct alignment with the

electromagnet.

CHESHIRE, CT 203-699-3300 CUST. SERV. FAX 203-699-3365 TECH SERV. FAX 203-699-3078

28 30 32 34 36 38 40 42 44 46 48

26 (660) 28 (711) 29 7/8 (759) 32 (813) 34 (864) 36 (914) 38 (965) 40 (1016) 42 (1067) 43 7/8 (1114) 45 5/8 (1159)

25 5/8 (651) 27 5/8 (702) 29 5/8 (752) 31 3/4 (806) 33 3/4 (857) 35 3/4 (908) 37 3/4 (959) 39 3/4 (1010) 41 3/4 (1060) 43 5/8 (1108) 45 3/8 (1153)

25 1/4 (641) 27 1/4 (692) 29 1/4 (743) 31 3/8 (797) 33 1/2 (851) 35 1/2 (902) 37 3/8 (949) 39 1/2 (1003) 41 1/2 (1054) 43 3/8 (1102) 45 1/4 (1149)

24 5/8 (625) 26 3/4 (679) 28 3/4 (730) 30 7/8 (784) 33 (838) 35 (889) 37 (940) 39 1/8 (994) 41 1/8 (1045) 43 (1092) 44 7/8 (1140)

23 3/4 (603) 25 7/8 (657) 28 (711) 30 1/8 (765) 32 1/4 (819) 34 3/8 (873) 36 3/8 (924) 38 1/2 (978) 40 5/8 (1032) 42 1/2 (1080) 44 3/8 (1127)

23 3/4 (603) 25 (635) 27 1/4 (692) 29 3/8 (746) 31 1/2 (800) 33 3/4 (857) 35 7/8 (911) 38 (965) 40 (1016) 42 (1067) 43 7/8 (1114)

21 3/4 (552) 24 (610) 26 1/4 (667) 28 1/2 (724) 30 3/4 (781) 33 (838) 35 1/8 (892) 37 1/4 (946) 39 3/8 (1000) 41 3/8 (1051) 43 3/8 (1102)

20 (508) 22 1/2 (572) 25 (635) 27 3/8 (695) 29 3/4 (756) 32 (813) 34 1/4 (870) 36 1/2 (927) 38 5/8 (981) 40 5/8 (1032) 42 1/2 (1080)

18 1/4 (463) 21 (533) 23 1/2 (597) 26 (660) 28 1/2 (724) 30 7/8 (784) 33 1/8 (841) 35 3/8 (899) 37 5/8 (956) 39 5/8 (1006) 41 5/8 (1057)

18 3/4 (476) 21 5/8 (549) 24 3/8 (619) 27 (686) 29 3/8 (746) 31 3/4 (806) 34 1/8 (867) 36 1/2 (927) 38 5/8 (981) 40 3/4 (1035)

22 1/2 (572) 25 1/2 (648) 28 1/8 (714) 30 5/8 (778) 33 1/8 (841) 35 5/8 (905) 37 7/8 (962) 40 (1016)

Do not install outlet box if

26 1/4 (667) 29 (737) 31 5/8 (803) 34 1/4 (870) 36 1/2 (927) 38 5/8 (981)

Dimensions X and Y intersect in this blank area.

29 3/4 (756) 32 1/2 (826) 34 7/8 (886) 37 1/8 (943)

The armature and electromagnet cannot be aligned.

27 3/4 (705) 30 5/8 (778) 33 (838) 35 3/8 (899)

31 3/8 (797) 33 7/8 (860)

X = Dimension of door jamb to wall

Y = Dimension of door width

1. Using a 5/32" Allen wrench, turn the contact plate adjusting

screw (Figures 5 and 6) counterclockwise to loosen the

contact plate.

2. Place the transfer marking points in the armature mounting

holes (Figure 4).

120V AC 24V AC/

COM

FRONT

VIEW

TOP

VIEW

Figure 3. Terminal Block

b. Surface concealed mounting (Figure 6). Measure two

points for 1/8" holes drilled 1/2" on center equidistant

from each marked point. Center punch the holes and

drill 1/8" diameter x 1 1/4" deep. Install the concealed

mounting plate using the two #10 x 1 1/2" screws

provided.

NOTE: Surface concealed mounting is not recommended for

hollow metal, hollow core, or composite type wood

doors.

Align the holes for the concealed mounting plate in the

armature base with the pins on the concealed mounting

plate. Secure the armature assembly, with the contact

plate adjust screw facing down, to the door by tightening

the set screw as shown in Figure 6.

5. Align the contact plate against the electromagnet. The

contact plate must be centered and lie flat against the magnet

to ensure sufficient holding force. Tighten the contact plate

adjusting screw until the plate is firm but not set. Do not

overtighten the contact plate.

6. Recheck alignment and adjust if necessary.

7. Adjust the door closer to exert 3 pounds of force when the

door is open and armature and magnet are in contact.

8. Energize the electromagnet and open the door(s). If the

door shuts, check that power is turned on to the unit and

that the magnet is energized and check the alignment of the

contact plate and electromagnet.

Figure 2. Mounting

Figure 4. Mounting the Armature Assembly

Mounting holes

Armature

(base view)

2 Transfer points

3. To locate the two mounting holes in the door, hold the contact

plate centered against the magnet, open the door and press

against the transfer marking points on the armature base.

Release the door and remove the transfer marking points.

4. Mount the armature assembly using one of the following

methods:

a. Thru-bolt mounting (Figure 5). Center punch the two

holes (at the points marked in step 3) and drill 5/16"

diameter through the door. Distance between the center

points should equal 1 3/4".

NOTE: Thru-bolt mounting is recommended for standard

1 3/4" hollow metal, hollow core or composite type

wood doors.

Secure the armature assembly, with the contact plate

adjust screw facing down, to the door as shown in Figure

5 using (2) #1/4-20 x 2" screws (supplied).

NOTE: For 2" doors, use (2) 1/4-20 x 2-1/4" bolts.

P/N 3100539 ISSUE 1

501-152800-0-01

PAGE 2

Top of

door

Lock edge

of door

2 3/8"

(60 mm)

2 5/8" (67 mm)

approx.

5" (127 mm)

approx.

1 11/16"

(43 mm)

Mounting holes

rmature

(base view)

1 3/4"

Door Plate

1 5/8"

DOOR

(2) #1/4-20 x 2"

screws provided

for a standard

1 3/4"

door

2" from floor to center

Contact plate

adjusting screw

Holes for

concealed

mounting

plate

rmature

(base view)

Figure 5. Thru-Bolt Mounting

Figure 6. Surface Concealed Mounting

Single gang

outlet box

(by others)

Electromagnet

bracket

assembly

(side view)

Cover

(side view)

Cover

(front view)

2 3/4 po

(70 mm)

4 5/8 po

(117 mm)

(2) 6-32 x

1/2 po (13 mm)

screws (supplied)

(2) 6-32 x

3/8 po (9.5 mm)

screws (supplied)

Concealed

mounting

plate

1/2"

Two #10 x 1 1/2"

screws (supplied)

Set screw.

Tighten with 6/32" Allen wrench

to secure armature onto

mounting plate.

Door

Contact plate

adjusting scre

1/2"

Instructions pour l’installation des dispositifs électromagnétiques de

retenue de porte à montage mural encastré, séries 1509

501-152800-0-01

Description

Les appareils de la série 1509 sont des dispositifs à montage

mural encastrés, conçus pour retenir une seule porte. Tous les

modèles sont homologués UL et cUL et approuvés FM.

Installation

Posez et raccordez le câblage conformément à tous les codes et

normes applicables, p. ex. publications NFPA 70 (National Elec-

trical Code), 72 (National Fire Alarm Code) et 80 (Standard for Fire

Doors and Fire Windows) et/ou tout autre règlement applicable

dans le pays et la localité où a lieu l’installation, ainsi qu’aux

exigences des autorités compétentes.

1. À partir le la Figure 1, repérez l’intersection des dimensions

X et Y dans le tableau 2. La dimension Z correspond à la

valeur indiquée à cette intersection dans la partie grisée.

Remarque : Si la dimension X ou Y ne figure pas dans le

tableau, déterminez la dimension Z par

extrapolation (p. ex., si X = 7 et Y = 30, Z =

(27-5/8 – ((27-5/8 – 27-1/4)/2)) =>

Z = 27-9/16 po)

2. Fixez une boîte de sortie de format simple (non fournie)

verticalement sur l’axe central horizontal et à 5 po (127 mm)

du haut de la porte.

Remarque : la boîte de sortie doit pouvoir résister à une force

maximale de retenue de 50 livres.

Si l’intersection de X et Y est dans la partie blanche du tableau 2,

N’installez PAS la boîte de sortie. Il est impossible d’aligner la

plaque de contact et l’électroaimant avec ces dimensions.

Tableau 1. Caractéristiques électriques

de cat. Volts Ampères

1509-E1 12V c.c. 0,170

1509-E5 12V c.a. 60 Hz 0,150

1509-AQN5 24V c.a. 60 Hz 0,015

24V c.c. 0,015

120V c.a. 60 Hz 0,015

Montage de l’électroaimant et du couvercle

MISE EN GARDE

Pour éviter les chocs électriques, vérifiez que

l’électricité est coupée.

1. Tirez les fils du circuit dans le conduit et faites-les entrer

dans la boîte de sortie (Fig. 2).

2. Établissez la continuité des masses (terre) conformément aux

codes, normes et exigences pertinentes de l’autorité

compétente. Un conducteur vert isolé est fourni à cet effet

sur les modèles –AQN5.

3. Pour les modèles -E1 et -E5, raccordez le câblage externe aux

conducteurs du dispositif électromagnétique.

Pour le modèle -AQN5, effectuez les raccordements comme

suit en vous référant à la figure 3 :

a. Modèles 120 V c.a. Branchez les fils du circuit externe

aux bornes marquées «120V AC» et «COM».

b. Modèles 24 V c.a./c.c. Branchez les fils du circuit externe

aux bornes marquées «24V AC/DC» et «COM».

4. Fixez le support de l’électroaimant à la boîte de sortie au

moyen des 2 vis n

6-32 x 1/2 po fournies (voir Fig. 2).

5. Fixez le couvercle au support de l’électroaimant au moyen

des 2 vis n

6-32 x 3/8 po fournies (voir Fig. 2).

Remarque : Une fois installé, le dispositif de retenue de porte

dépasse de la surface du mur de 1-27/32 po.

Montage de l’armature

Remarque : L’armature doit être montée verticalement (Fig.

4) pour être bien alignée avec l’électroaimant.

Porte

Montant de porte

Surface

du mur

Boîte de sortie

Axe

central