Master TB118A Le manuel du propriétaire

IMPORTANT: Read and understand this manual before

assembling, starting or servicing heater. Improper use

of heater can cause serious injury. Keep this manual for

future reference.

GENERAL HAZARD WARNING:

Failure to comply with the precautions and instructions

provided with this heater, can result in death, serious

bodily injury and property loss or damage from hazards



poisoning and/or electrical shock.

Only persons who can understand and follow the instruc-

tions should use or service this heater.

If you need assistance or heater information such as an in-

structions manual, labels, etc. contact the manufacturer.

Save this manual for future reference.

For more information, visit www.desatech.com

PROPANE TENT EVENT

FORCED AIR HEATER

OWNER’S MANUAL

MODELS TB116A, TB117A AND TB118A

125,000 BTU/HR

125

TENT

Event

by

www.desatech.com

120942-01E2

WARNING: If the information in this manual is not



property damage, personal injury or loss of life.

 -

pors and liquids in the vicinity of this or any other

appliance.

— WHAT TO DO IF YOU SMELL GAS

 

 

phone in your building.

 



 

department.

— Installation and service must be performed by a quali-



If you smell gas, turn off gas supply at tank.

-

gen) from the tent in which it is installed. Provisions for

adequate combustion and ventilation air must be pro-

vided. Provide at least 42 square inches of opening.

State of Massachusetts: The installation must be made



of Massachusetts.

TABLE OF CONTENTS

Safety .................................................................. 3

Ventilation ............................................................ 5

Product Identication ........................................... 6

Propane Supply ................................................... 6

Electrical Supply .................................................. 7

Unpacking............................................................ 7

Theory of Operation............................................. 8

Assembly ............................................................. 9

Installation ..........................................................11

Operation ........................................................... 12

Storage .............................................................. 13

Maintenance ...................................................... 13

Service............................................................... 13

Specications .................................................... 17

Troubleshooting ................................................. 18

Technical Service............................................... 19

Wiring Diagram .................................................. 20

Parts .................................................................. 22

Replacement Parts ............................................ 26

Accessory .......................................................... 26

Warranty ............................................................ 28

www.desatech.com

120942-01E 3

SAFETY

General

ANSI/NFPA 102

Standard for Grandstands, Folding and

telescopic Seating, Tents and Mem-

brane Structures

ANSI/NFPA 58

Standard for Storage and Handling of

Liquieed Petroleum Gas Latest Edition

ANSI Z223.1/NFPA 54

National Fuel Gas Code Latest Edition

ANSI/NFPA 70

National Electric Code Latest Edition

CSA C22.1 Canadian Electrical Code

Part 1

The primary purpose of construction heaters

is to provide temporary heating of buildings

under construction, alteration or repair.

Properly used, the heater provides safe eco-

nomical heating. Products of combustion are

vented into the area being heated.

We cannot foresee every use which may be

made of our heaters. 



about heater use.

Other standards govern the use of fuel gases

and heat producing products for specific

uses. Your local authorities can advise you

about these.

WARNING: When used with-

out adequate combustion and

ventilation air, heater may give



an odorless, poisonous gas.

Do not install heater until all necessary provi-

sions are made for combustion and ventilation

air. Consult the written instructions provided with

the heater for information concerning combus-

tion and ventilation air. In the absence of instruc-

tions, refer to the national fuel gas code, ANS

Z223.1, Section 5.3 or applicable local codes.

This heater is equipped with a an Oxygen

Depletion Sensing (ODS) safety shutoff

system designed to turn off the heater if not

enough fresh air is available.



depletion safety system!

If heater shuts off, do not relight until you

provide fresh air. If heater keeps shutting off,

have it serviced. Keep burner and control

compartment clean.

WARNING: This product

contains and/or generates

chemicals known to the State



birth defects or other reproduc-

tive harm.

WARNING: Fire, burn, inhala-



solid combustibles, such as

tables, chairs, building materi-

als, paper or cardboard, a safe

distance away from the heater

as recommended by the instruc-

tions. Never use the heater in

spaces which do or may contain

volatile or airborne combustibles

or products such as gasoline,

solvents, paint thinner, dust par-

ticles or unknown chemicals.

WARNING: Not for home or

recreational vehicle use.

The heater is designed and approved for use

as a tent heater in accordance with these

instructions. CHECK WITH YOUR LOCAL

FIRE SAFETY AUTHORITY IF YOU HAVE

QUESTIONS ABOUT APPLICATIONS.

The heater is designed for use as a construc-

tion heater and as a vent-free tent heater. The

heater is designed for use in the space being

heated. The heater uses the air from within

the space being heated for combustion and

ventilation.

Applicable Standards:

For USA applications

ANSI Z83.7 - 2000

Gas Fired Construction Heaters

CGA 2.14 - 2000

Gas Fired Construction Heaters

CSA 3.06 - 2006

Portable Gas Fired Unvented Tent Heaters

For Canadian applications

ANSI Z83.7 - 2000

Gas Fired Construction Heaters

CGA 2.14 - 2000

Gas Fired Construction Heaters

www.desatech.com

120942-01E4

SAFETY

Continued

Note: Fan will continue running if fuel supply

is exhausted or thermal switch opens.



poisoning may lead to death!

   Early signs

of carbon monoxide poisoning resemble the

u, with headaches, dizziness, and/or nausea.

If you have these signs, the heater may not

be working properly. Get fresh air at once!

Check for proper ventilation and have heater

serviced. Some people are more affected by

carbon monoxide than others. These include

pregnant women, people with heart or lung

disease or anemia, those under the inuence

of alcohol, and those at high altitudes.

Propane/LP Gas: Propane/LP gas is odorless.

An odor-making agent is added to propane/LP

gas. The odor helps you detect a propane/LP

gas leak. However, the odor added to propane/

LP gas can fade. Propane gas may be present

even though no odor exists.

Make certain you read and understand all

warnings. Keep this manual for reference. It

is your guide to safe and proper operation of

this heater.

WARNING: Do not place

-

terial on or near the appliance.

WARNING: Due to high tem-

peratures, the appliance should



from furniture.

WARNING: Young children

should be carefully supervised

when they are in the same room

with the appliance.

   

adults should be alerted to the

hazard of high surface tempera-

ture and should stay away to avoid

burns or clothing ignition.



or guard removed for servicing

an appliance must be replaced

prior to operating the heater.

1. Install and use heater with care. Follow all

local ordinances and codes. In the absence

of local ordinances and codes, refer to

the Standard for Storage and Handling of

Liqueed Petroleum Gas, ANSI/NFPA 58,

the Natural Gas and Propane Installation

Code, CSA B149.1, and ANSI/NFPA 102

Standard for Grandstands, Folding and

telescopic Seating, Tents and Membrane

Structures. This instructs on the safe stor-

age and handling of propane/LP gases.

2. Use only the electrical voltage and fre-

quency specied on model plate. The

electrical connections and grounding of

the heater shall follow the National Electric

Code, ANSI/NFPA 70 or the Canadian

Electrical Code, Part 1, CSA C22.1.

3. Electrical Grounding Instructions - This

appliance is equipped with a three-prong

(grounding) plug for your protection against

shock hazard and should be plugged di-

rectly into a properly grounded three-prong

GFI receptacle or extension cord.

4. Use only the hose and factory preset

regulator provided with the heater.

5. Use only propane/LP gas set up for vapor

withdrawal.

6.

This is an unvented gas-red tent heater.

It uses air (oxygen) from the tent in which

it is installed. Provide adequate ventilation.

Before using heater, provide at least a 42 in

2

(271 cm

2

) opening of fresh, outside air.

7. For indoor and outdoor use.

8. Do not use heater in occupied dwellings

or in living or sleeping quarters.

9. Do not use heater in basement or below

ground level. Propane/LP gas is heavier

than air. If a leak occurs, propane/LP gas

will sink to the lowest possible level.

10. Keep appliance area clear and free from

combustible materials, gasoline, paint

thinner, and other ammable vapors and

liquids. Dust is combustible. Do not use

heater in areas with high dust content.

www.desatech.com

120942-01E 5

29. The heater must be installed so that the

location of the heater does not obstruct or

interfere with normal or emergency exits

and doors or walkways in the structure.

30. Only use lifting handles to pick up appli-

ance (see Figure 1, page 6). Do not use

plastic top hand holds for lifting.

VENTILATION

WARNING: Follow the mini-

mum fresh, outside air ventila-

tion requirements. If proper

fresh, outside air ventilation is



poisoning can occur. Provide

proper fresh, outside air ventila-

tion before running heater.

Provide a fresh air opening of at least 42 in

2

(271 cm

2

) opening of fresh, outside air.

Example: 3" high x 14" long = 42 in

2

. Provide

extra fresh air if more heaters are being used.



1. Determine volume of space to heat:

Length x Width x Height

50 feet x 30 feet x 15 feet = 22,500 ft

3

2. Determine desired temperature rise:

Desired temperature 65° - 25° outside

temperature = 40° rise

3.

Multiply volume x rise: 22,500 x 40 = 900,000

4.

To determine how many BTU’s are needed

multiply by 0.133

900,000 x 0.133 = 119,000 Btu

The heater thermostat will cycle on and off to

maintain the desired room temperature more

often if the BTU/hr is oversized for the space

being heated. The air inltration and leakage

of heated air through cracks, passageway

openings, etc., will adjust the required BTU’s

needed for the desired temperature.

Ventilation Air Requirements - National



1 inch

2

of opening per 3,000 BTU with

outside air

1 inch

2

of opening per 1,000 BTU with non-

outside air

Determine fresh air needed

Input Max. divided by 3,000

125,000 BTU/hr ÷ 3,000 = 41.66

Provide 42 inch

2

of opening to fresh, outside air

3" high x 14" long - 42 inches

2

11. Minimum heater clearances from com-

bustible materials: Outlet: 8 ft. (2.40 m),

Sides: 1 ft. (30 cm), Top: 3 ft. (0.91 m),

Rear: 1 ft. (30 cm)

12. Keep heater at least 6 ft. (1.83 m) from

propane/LP tank(s). Do not point heater

at propane/LP tank(s) within 20 ft. (6 m).

In Canada keep heater at least 10 ft. (3 m)

from propane/LP tank(s).

13. Keep propane/LP tank(s) below 100° F

(38˚ C).

14. The minimum surrounding air temperature

rating for this heater is -20º F (-29º C).

15. Check heater for damage before each

use. Do not use a damaged heater.

16. Check hose before each use of heater.

If highly worn or cut, replace with hose

specied by manufacturer before using

heater.

17. Locate heater on stable and level surface

if heater is hot or operating.

18. Never block air inlet (rear) or air outlet

(front) of heater.

19. Keep heater away from strong drafts, wind,

water spray, rain, or dripping water.

20. Keep children and animals away from

heater.

21. Never move, handle, or service a hot

or operating heater. Severe burns may

result. You must wait 15 minutes after

turning heater off.

22. To prevent injury, wear gloves when han-

dling heater.

23. Never attach duct work to heater.

24. Space heaters used in the vicinity of tarpau-

lins, canvas or similar enclosure materials

shall be located a safe distance from such

materials. These enclosure materials shall

be of a re retardant nature. These enclo-

sure materials shall be securely fastened to

prevent them from igniting or from upsetting

the space heater due to wind action.

25. Do not alter heater. Keep heater in its

original state.

26. Do not use heater if altered.

27. Turn off propane/LP supply to heater and

unplug when not in use.

28. Use only original replacement parts. This

heater must use design-specic parts.

Do not substitute or use generic parts.

Improper replacement parts could cause

serious or fatal injuries.

SAFETY

Continued

www.desatech.com

120942-01E6

Figure 1 - Tent Heater

Top

Power Cord

Hose and

Regulator

Assembly

Gas Inlet

Lifting

Handle

Thermostat

Knob

ON/OFF

Switches

Receptacle

PROPANE SUPPLY

PRODUCT IDENTIFICATION

1. The amount of propane gas in tank(s)

2. The temperature of tank(s)

The following chart shows the number of

100 lb. (45 kg) tanks needed to run this

heater.

Smaller tanks can be used for limited run

times but it is recommended to use larger

tanks for optimum performance.

Average Temperature Number Of Tanks

  

Above 20° F (-6.7° C) 2

20° F (-6.7° C) to 0° F (-18° C) 3

Below 0° F (-18° C) Use larger tank

Less gas is vaporized at lower temperatures.

You may need two or more 100 lb. (45 kg)

tanks or one larger tank in colder weather.

Your local propane gas dealer will help you

select the proper supply system. The mini-

mum surrounding air temperature rating for

each heater is -20° F (-29° C).

Propane/LP gas and propane tank(s) are to

be furnished by the user.

Use this heater only with a propane vapor

withdrawal supply system. See Chapter 5

of the Standard for Storage and Handling

of Liqueed Petroleum Gas, ANSI/NFPA 58

and the Natural Gas and Propane Installation

Code CSA B149.1. Your local library or re

department will have this booklet.

Keep propane/LP tank(s) at least 5 ft away

from the side of the tent.

The propane/LP tank(s) shall be protected

from vehicles and secured in accordance

with the Standard for Grandstands, Folding

and Telescopic Seating, Tents and Membrane

Structures NFPA 102 and the Standard for

Storage and Handling of Liquieed Petroleum

Gases ANSI/NFPA 58.

The amount of propane gas ready for use

from propane tanks varies. Two factors decide

this amount:

Hand Holds

for Pushing

www.desatech.com

120942-01E 7

ELECTRICAL SUPPLY

This heater requires an electrical supply to

be furnished by the user. The electrical outlet

should have the following ratings:

120 volts (+/- 10%), 60 Hertz, 15 Amps

Ground Fault Interrupter (GFI)

The heater uses the ground circuit to prove the

ame by sending a low voltage (40 mV DC)

signal back to the DSI control. If the ground

supply is not correctly wired or is missing, the

heater will not work.



Extension cords used to connect the heater

must be 3 prong, grounded type of proper

gauge. Extension cord requirements are as

follows:

• Up to 100 feet (30 m), use 16 AWG rated

cord

• 101 to 200 feet (32 to 60 m), use 14 AWG

rated cord.

OPERATION WITH PORTABLE

GENERATOR

WARNING: Before operating

heater or any appliance from a

portable generator, verify that

generator has been properly con-

nected to earth ground. Improper

grounding or failure to ground

generator can result in electro-

cution if a ground fault occurs.



by generator manufacturer for

proper grounding procedures.

The operating voltage range of the heater is

108 to 132 Volts (120 Volts +/- 10%). Prior

to plugging heater into generator the output

voltage should be veried (if generator is

equipped with the automatic idle feature, the

output voltage should be measured with the

generator running at full speed). If the voltage

does not measure in this range the heater

should not be plugged into the generator.

UNPACKING

1. Remove all packing items applied to

heater for shipment. Keep plastic cover

caps (attached to inlet connector and

hose/regulator assembly) for storage.

2. Remove all items from carton.

3. Check all items for shipping damage. If

heater is damaged, promptly inform dealer

where you bought heater.

www.desatech.com

120942-01E8

Figure 2 - Cross Section Operational View

Clean

Heated

Air Out

(Front)

Combustion Chamber

Hose/Regulator

Assembly

Injector

Motor and

Blower

Assembly

Cool

Air In

(Back)

Power Cord

Fuel

DSI

Air for Fuel

System

Thermal Switch

Ignitor, Flame

Sensor and ODS

Burner

Air Pressure Switch

THEORY OF OPERATION

The Fuel System: The hose/regulator assembly attaches to the propane gas supply. The

propane gas moves through the automatic control valve and out the injector.

The Air System: The motor turns the fan. The fan pulls air into and around the combustion

chamber. This air is heated and provides a stream of clean, hot air.

The Ignition System: The direct spark ignitor (DSI) sends voltage to the spark ignitor. The

spark ignitor ignites the fuel and air mixture.

 There are 4 independent systems:

1. Flame Sensor: This system causes the heater to shut down if the ame goes out.

2. Thermal Switch: This system causes the heater to shut down if the heater gets too hot

(blocked openings).

3. Air Pressure Switch: The system will not allow the heater to start if there is not adequate

air ow.

4.  This system shuts down the heater if the oxygen level

drops below the specied level (18%).

ODS Operation: Burner porting "blows" out causing ame sensor to cool, shutting down heater.

www.desatech.com

120942-01E 9

ASSEMBLY

Figure 3 - Attaching Handles

Handle

Screw

Nut

Lock Washer

Figure 4 - Installing Casters

Nut

Flat Washer

Caster

ASSEMBLY ITEMS

Before assembling heater, make sure you have the items listed below.

• Phillips head screwdriver

• Wrench

• Hardware packet

Handles (2), 3/4" Screws (4), 1/4-20 Nuts (4), 1/4 Flat washers (4), 1/4 Lock washers (4)

Casters (2), 3/8" Nut (2), 3/8 Lock washers (2), 3/8 Flat Washers (4)

Wheels (2), Cotter Pins (2)

Brackets (4), 1/2" black screws (8), 3/8" screws (8)

Note: Place metal parts on packaging during assembly to protect from scratches.



1. Remove casters, 3/8 at washers, 3/8

lock washers and 3/8 nuts from hardware

packet.

2. You may wish to remove side panel from

heater to make installing casters easier.

If so, see Top and Side Panel Removal

on page 14. Figure 4 shows side panel

removed for clarity.

3. Use a spacer to prop end of heater up

so holes in base can be accessed (the 2

wheels stacked on top of each other will

accomplish this).

4. Place a at washer onto threaded stem of

caster. Insert caster stem through hole in

cabinet base as shown in Figure 4.

5. Attach each caster to base with a at

washer, a lock washer and a nut as shown

in Figure 4.

Side Handles

1. Remove handles, 3/4" screws, 1/4-20

nuts, 1/4 at washers and 1/4 lock wash-

ers from hardware packet.

2. Attach each handle to side panels with 2

screws, 2 nuts, 2 at washers and 2 lock

washers. Insert screw from outside of

heater and through handle. From inside

of heater, attach a at washer, then a lock

washer then a nut as shown in Figure 3.

Flat Washer

Lock Washer

www.desatech.com

120942-01E10

Bracket

Top

Bracket

Screws

Figure 6 - Attaching Top

ASSEMBLY

Continued

Figure 5 - Installing Axle and Wheels

Heater

Front

Axle

Wheel

Cotter Pin



1. Locate wheels, washers, cotter pins and

axle in hardware packet.

2. Carefully slide axle through heater body

as shown in Figure 5.

3. Slide one wheel and washer onto axle.

Insert cotter pin into end of axle. See

Figure 5.

4. Repeat steps 2 and 3 for second wheel,

washer and cotter pin on other side of

heater.

3. Turn top over and carefully place over

heater, positioning brackets through slots

in heater front and rear panels.

4.

Attach brackets to heater with 3/8" screws.

Bracket

Slots

Washer

Top

1. Remove 4 brackets, (8) 1/2" black screws

and (8) 3/8" screws from hardware

packet.

2. Lay top upside down on a clean surface.

Attach 4 brackets to top with 1/2" black

screws.

www.desatech.com

120942-01E 11

INSTALLATION

2. Connect fuel gas connector fitting on

hose/regulator assembly to propane

tank(s) (see Figure 7). Turn counterclock-

wise into threads on tank valve. Tighten

rmly using wrench.

IMPORTANT: Tighten regulator with vent

pointing down. Pointing vent down pro-

tects regulator from weather damage.

3. Connect hose to inlet connector (see

Figure 8). Tighten rmly using a wrench.

IMPORTANT: Extra hose or piping may be

used if needed. Install extra hose or piping

between hose/regulator assembly and

propane tank. You must use the regulator

supplied with heater.

4. Open propane supply valve on propane

tank(s) slowly.

Note: If not opened slowly, excess ow

check valve on propane tank will stop gas

ow. If this happens, close propane supply

valve and open again slowly.

5. Check all connections for leaks. Correct

all leaks.

Figure 7 - Regulator With Vent Pointing

Down

Hose

Regulator

Vent

(pointing

down)

Fuel Gas

Connector

Supply Valve

Propane

Tank

Figure 8 - Hose and Inlet Connector

Hose

Inlet

Connector

WARNING: Review and un-

derstand the warnings in the

Safety section, page 2. They are

needed to safely operate this

heater. Follow all local codes or

in the absence of local codes,

with the Standard for Grand-

stands, Folding and Telescopic

Seating, Tents and Membrane

Structures NFPA 102 and the

Standard for Storage and Han-

dling of Liquieed Petroleum

Gases ANSI/NFPA 58.

WARNING: Test all gas piping

and connections for leaks after

installation or servicing. Never



leak. Apply a noncorrosive leak

-

able at local plumbing supply

stores). Bubbles forming show a



1. Provide propane supply system (see

Propane Supply, page 6).

www.desatech.com

120942-01E12

OPERATION



1. Press Switch 1 to ON.

2. Press Switch 2 to ON.

3. Adjust thermostat knob to desired

comfort level.

Note: Fan will stay on when burner cycles off.

FAN ONLY WITH NO HEAT

1. Turn gas supply off.

2. Press Switch 1 to OFF.

3. Press Switch 2 to ON.

4. Adjust thermostat knob to Fan Only

position.

TO STOP HEATER

1. Tightly close propane/LP supply valve on

propane tank(s).

2. Wait a few seconds. Heater will burn gas

left in supply hose.

3. Press on/off switches to the OFF position.

4. Unplug heater.

TO RESTART HEATER

1. Press on/off switches to the OFF position.

2. Reconnect extension cord.

3. Turn on gas supply valve.

4. Follow To Start Heater instructions, col-

umn 1.

Thermostat

Fan Cycle

ON

OFF

Switch 1

Fan

Continuous

ON

THERMOSTAT

CYCLE

LOW

Fan Only

HIGH

OFF

Switch 2

8

1

2

3

4

5

6

7

Thermostat Knob

Figure 9 - Control Panel

WARNING: Review and un-

derstand the warnings in the

Safety section, page 2. They are

needed to safely operate this

heater. Follow all local codes

when using this heater.

TO START HEATER

1. Follow all installation, ventilation and

safety information.

2. Connect regulator/hose assembly to gas

supply.

3. Check for leaks using a noncorrosive leak

detection uid. Bubbles forming indicate a

gas leak. Correct all leaks before attempt-

ing to operate heater.

4. Locate heater on a stable and level sur-

face. Make sure strong drafts do not blow

into front or rear of heater.

5. Plug power cord of heater into a three

prong, grounded extension cord. Exten-

sion cord must be at least 6 feet (1.83 m)

long, CSA listed and of proper size.



Up to 100 ft. (30 m) long, use 16 AWG

rated cord.

101 to 200 ft. (31 to 60 m) long, use 14

AWG rated cord.

6. Plug extension cord into a 120v/60 hz,

three hole, grounded GFI outlet.

7. Open gas supply valve slowly.

Note: If heater burner does not ignite,

turn gas supply off and open slowly. The

hose/regulator assembly is equipped with

an excess ow safety valve. An audible

"click" is heard when opened too fast.

8. Choose desired function:

THERMOSTAT OPERATION WITH HEAT

1. Press Switch 1 to ON.

2. Press Switch 2 to OFF.

3. Adjust thermostat knob to desired

comfort level.

Note: Fan will cycle on and off with burner.

www.desatech.com

120942-01E 13

STORAGE

2. Place plastic cover caps over brass ttings

on inlet connector and hose/regulator as-

sembly.

3. Store in dry, clean, and safe place.

4. When taking heater out of storage, always

check inside of heater. Insects and small

animals may place foreign objects in

heater. Keep inside of heater free from

combustible and foreign objects.





1. Store propane tank(s) in safe manner. See

Chapter 5 of Standard for Storage and

Handling of Liqueed Petroleum Gases,

ANSI/NFPA 58 and the Natural Gas and

Propane Installation Code CSA B149.1.

Follow all local codes. Always store pro-

pane tanks outdoors.

MAINTENANCE

WARNINGS

 

is plugged in, connected to

propane supply, operating, or

hot. Severe burns and electri-

cal shock can occur.

     

from combustible materials,



vapors and liquids.

 -

bustion or ventilation air.

1. Keep heater clean. Clean heater annually

or as needed to remove dust and debris.

If heater is dirty or dusty, clean heater

with a damp cloth. Use household clean-

ers on difcult spots. Slight odor may be

present for a brief period following use of

household cleaners.

2. Inspect heater before each use. Check

connections for leaks. Apply a noncor-

rosive leak detection uid to connections.

Bubbles forming show a leak. Correct all

leaks at once.

3. Inspect hose/regulator assembly before

each use. If hose is highly worn or cut,

replace with one specied by manufac-

turer.

4. Have heater inspected yearly by a quali-

ed service agency.

5. Keep inside of heater free from combus-

tible and foreign objects. Remove motor

and other internal parts if needed to clean

inside of heater (see Service, below).

Burner

Check burner air inlet after every 300 hours

of operation to ensure burner air inlet is free

of dust or debris. Use compressed air (30 PSI

or less) to clean out burner air inlet.

SERVICE

WARNING: Never service

heater while it is plugged in,

connected to propane supply,

operating, or hot. Severe burns

and electrical shock can occur.

IMPORTANT: CHECK FOR GAS LEAKS. Test

all gas piping and connections for leaks after

installation or servicing. Never use an open

ame to check for a leak. Apply a noncorrosive

leak detection uid to all joints (available at lo-

cal plumbing supply stores). Bubbles forming

show a leak. Correct all leaks at once.

www.desatech.com

120942-01E14

SERVICE

Continued





1. Remove top and side panel (see Top and

Side Panel Removal, above).

2. Locate wiring diagram on inside of side

panel or go to page 20.

3. Check that all wiring terminals are se-

curely connected.

4. Check for gas leaks around ttings and

tubing of plumbing connections. See

page 11.

MOTOR AND BLOWER ASSEMBLY

1. Remove top and side panel (see Top and

Side Panel Removal, above).

2. Follow wires from blower/motor and dis-

connect from terminal blocks. Pull wires

out and coil excess to prevent damage to

insulation.

TOP AND SIDE PANEL REMOVAL

1. Remove 8 screws securing top brackets

to body panels. Remove top and set aside

(see Figure 10).

Brackets

Located

Underneath

Figure 10 - Removing Top and Side Panel

Side

Panel

Top

Bracket

Screws

Side Panel

Screw

2. Remove 2 screws securing side panel

at top edge. Remove 3 screws at lower

outside edge (see Figure 10). Push down

and lift out side panel.

3. Carefully remove 9 screws securing

blower mounting panel (see Figure 11,

page 15). Slide bafe top up and care-

fully lift entire assembly out of heater.

Assembly is heavy. Removal may require

assistance.

4. Remove 4 nuts securing blower/motor to

mounting panel.

5. Attach new blower/motor to mounting

panel and reinstall in reverse order. Insert

blower mounting panel under lip of bafe

top. Use care when removing or installing

blower to mounting panel to avoid dam-

age to wiring. Reattach wiring referring to

Wiring Diagram on page 20.

www.desatech.com

120942-01E 15

Figure 11 - Removing Blower/Motor Assembly

Terminal

Blocks

Blower/Motor

Blower

Mounting

Panel

Bafe Top

Figure 12 - Back Panel and Screen

Figure 13 - Removing Burner

Burner

Solenoid Valve

Back Panel

Screen

BURNER, IGNITOR AND GAS



WARNING: Make sure heater

is disconnected from propane and

electrical supply. Heater could

ignite causing severe burns.

Remove top and side panel (see Top and Side

Panel Removal, see page 14).

Replacing Burner

1. Remove all visible screws from lower sec-

tion of back panel and screen (see Figure

12). Pull back panel out to gain access to

screen. Push screen up and over ange,

then slide out.

2. Disconnect orange ignitor wire from ignit-

or. Ignitor is attached to back of burner.

3. Disconnect gas line at solenoid valve

and at orice using a 5/8" wrench. Avoid

bending and set aside.

4. Remove 3 screws securing burner to

partition (see Figure 13). Rotate burner

clockwise and pull out of chamber.

Note: There is a cutout on the partition

that allows the ignitor and bracket to slide

out as a complete assembly. Use caution

when removing or installing burner to avoid

damaging or dislocating ignitor electrode.

5. After all service is complete, reinstall

burner in reverse order. Support burner

SERVICE

Continued

while inserting burner locator pin into hole

in chamber end panel. Replace screen

and back panel.

www.desatech.com

120942-01E16

Replacing Ignitor

1. To loosen back panel and gain access

to ignitor, follow step 1 under Replacing

Burner, page 15. Due to lack of working

area, burner assembly may be removed

to gain access to ignitor electrode, see

Replacing Burner, page 15.

2. Remove ignitor bracket screw and lift

ignitor.

3. Attach new ignitor with ignitor mounting

screw removed in step 2.

4. Install new ignitor. Ignitor gap between

ignitor electrode and burner deck is

0.10"/0.12" (2.5/3.0 mm).

5. With gas supply shut off, test for spark.

Plug into extension cord and watch for

spark between ignitor electrode and

burner deck.

SERVICE

Continued

Ignitor Gap

Figure 14 - Ignitor Gap



1. Hold burner flange and rotate orifice

counterclockwise to remove.

2. Install new orice

IMPORTANT: CHECK FOR GAS LEAKS. Test

all gas piping and connections for leaks after

installation or servicing. Never use an open

ame to check for a leak. Apply a noncorrosive

leak detection uid to all joints (available at lo-

cal plumbing supply stores). Bubbles forming

show a leak. Correct all leaks at once.



1. Remove top and side panel (see Top

Panel Removal, page 14).

2. Disconnect orange ignitor wire.

3. Remove white wire connector.

4. Remove 2 screws and nuts securing DSI

control.

5. Install new DSI control. Reconnect wiring.



1. Remove top and side panel (see Top and

Side Panel Removal, page 14).

2. Disconnect 2 blue wires.

3. Remove gas line.

4. Remove 2 screws and nuts holding valve

to mounting plate.

5. Remove brass ttings from old gas valve.

If damaged replace with new fittings.

Install ttings into new gas valve. Use

pipe joint sealant that is resistant to liquid

petroleum (LP) gas. Tighten all ttings.

6. Install new gas valve using screws and

nuts from step 4.

7. Connect blue wires to new gas valve.

8. Reconnect gas line.

IMPORTANT: CHECK FOR GAS LEAKS. Test

all gas piping and connections for leaks after

installation or servicing. Never use an open

ame to check for a leak. Apply a noncorrosive

leak detection uid to all joints (available at lo-

cal plumbing supply stores). Bubbles forming

show a leak. Correct all leaks at once.



PRESSURE

1. Remove top and side panel (see Top

Panel Removal, page 14).

2. Locate pressure tap on solenoid valve and

remove (retain plug for later installation).

See Figure 15, page 17.

3. Install 1/8 NPT barb tting with sealant on

threads into solenoid valve.

4. Connect to manometer or pressure gauge

that measures in inches of water.

5. Connect hose and regulator to heater and

tank.

6. Plug in and turn on.

www.desatech.com

120942-01E 17

SPECIFICATIONS

• Output Rating - 125,000 Btu/Hr (131,882 kJ/Hr)

• Fuel Consumption - 1.4 Gal/Hr (5.2 Liters/Hr), 5.8 lb/Hr (2.6 kg/Hr)

• Propane Vapor Fuel Only

• Manifold Pressure - 10" (25.4 cm) WC

• Supply Pressure To Regulator: Minimum (for purposes of input adjustment) 10 psi (69 kPa),

Maximum - Tank Pressure

• Regulator Outlet Pressure - 11" wc

• Electric Input - 120 V/60 Hz

• Amperage - Start 7, Run 3.5

• Load - 10 amps on receptacle

• Hot Air Output (Approx) - 1000 CFM (28.3 m

3

/min)

• Motor - 1,100 RPM, 1/4 HP

• Ignition - Electronic Direct Spark Ignition (D.S.I.)

• Ignitor Gap - 0.10"/0.12" (2.5/3.0 mm)

Figure 15 - Tent Heater Parts

Solenoid

Valve

Receptacle

DSI

Terminal

Boards

Thermostat

Switches

Gas Line

Burner

Pressure

Switch

SERVICE

Continued

Vacuum

Pressure

Tap

Thermal

Limit Switch

Injector

www.desatech.com

120942-01E18

REMEDY

1. Check voltage to electrical

outlet. If voltage is good,

check heater power cord for

breaks

2. Adjust thermostat to higher

setting

3. Wait for ambient temperature

to decrease

4. Replace motor. See Motor and

Blower Assembly, page 14

5. Check wiring for loose con-

nections or damage

1. Check gas supply, connec-

tions and hoses

2. Repeat installation and op-

eration instructions. See

Installation, page 11 and

Operation, page 12

3.

A) Check ignitor wire. Tighten

or reattach loose ignitor wire.

B) Assure gap between ignitor

electrode and burner deck is

0.10"/0.12" (2.5/3.0 mm). Do

not bend electrode. Doing so

may cause it to break

C) Replace ignitor elec-

trode. See Replacing Ig-

nitor, page 16

D) Replace spark trans-

former. See Replacing DSI

Control, page 16

3. Clean tubing



1. No electrical power to heater

2. Thermostat set too low

3. Ambient temperature is too

high. Thermostat is satis-

ed

4. Defective motor

5. Loose wiring connections

1. No fuel ow

2. User did not follow installa-

tion or operation instructions

properly

3. No spark at ignitor. To test

for spark, follow step 5 under

Replacing Ignitor, page 16. If

you see spark at ignitor, have

heater serviced by qualied

service person. If no spark

seen:

A) Loose or disconnected

ignitor wire

B) Wrong spark gap

C) Bad ignitor electrode

D) Bad spark DSI

3. Air proving switch blocked

OBSERVED FAULT

Fan does not turn when

switch(s) 1 or 2 are pressed

to ON

Heater will not ignite

TROUBLESHOOTING

WARNING: Never service heater while it is plugged in, connected

to propane supply, operating, or hot. Severe burns and electrical

shock can occur.

www.desatech.com

120942-01E 19

WARNING: Use only in areas

free of high dust content.

TROUBLESHOOTING

Continued

REMEDY

1. A) Rell tank

B) Provide additional and/or

larger tanks. See Propane

Supply, page 6

2. This can happen when running

heater in temperatures above

85° F (29˚ C). Run heater in

cooler temperatures

3. Check heater inlet and outlet.

Remove any obstructions

4.

Replace motor and blower as-

sembly. See page 13

5. Clean heater. See Mainte-

nance, page 13

1. Check all connections for

leaks. Apply noncorrosive leak

detection uid to gas joints.

Bubbles forming show a leak

that must be corrected

2. To obtain correct mixture of

propane/LP gas and air, use

a larger cylinder size, i.e.

100 lb. See Propane Supply,

page 6

3. Use a larger supply cylinder

size, i.e. 100 lb.



1. Propane supply may be

inadequate

2. High surrounding air tem-

perature causing thermal

limit device to shut down

heater

3. Restricted air ow

4. Damaged fan

5. Excessive dust or debris in

surrounding area

1. Gas leak

2. Heater operating on a 20 lb.

propane/LP cylinder. Insuf-

cient propane/LP gas will be

supplied by a 20 lb. cylinder

resulting in odor

3. Propane/LP supply tank is

"freezing up". Evaporation

and consumption rate of

propane/LP from supply tank

is to great for the size of the

tank and air temperature

OBSERVED FAULT

Heater shuts down while

running

Heater producing odor

TECHNICAL SERVICE

You may have further questions about installa-

tion, operation, or troubleshooting. If so, con-

tact DESA Heating, LLC at 1-866-672-6040.

When calling please have your model and

serial numbers of your heater ready.

You can also visit DESA Heating, LLC’s web

site at www.desatech.com.

www.desatech.com

120942-01E20

WIRING DIAGRAM

Electrical Connection Diagram

Motor

Moteur

VAC

Switch

(4)

Thermostat

Te rmostato

Receptacle

(6)

Switch 1

Cycle

(1)

White

Blanco/Blanc

White

Blanco/Blanc

White

Blanco

Blanc

White

Blanco

Blanc

White/Blanco/Blanc

White

Blanco

Blanc

White/Blanco/Blanc

Solenoid Valve/

Válvula de solenoide/

Électrovanne

DSI

(encendedor

de chispa

directa)

AED

Black

Negro

Noir

Black

Negro

Noir

Black

Negro

Noir

Black

Negro

Noir

Black

Negro

Noir

Orange

Naranja

Black

Negro

Noir

Green

Verde

Vert

Green

Verde

Vert

Green

Verde

Vert

Green

Verde

Vert

Blue

Azul

Bleu

Blue/Azul/Bleu

Red/Rojo/Rouge

Red

Rojo

Rouge

Red

Rojo

Rouge

Terminal Block

(3)

Terminal Block

(3)

Switch 2

Continuous

(2)

(1) Interruptor 1 ciclo automático/

Interrupteur 1 en cycle

(2) Interruptor 2 continuo/

Interrupteur 2 en continu

(3) Bloque de terminales/Bornier

(4) Interruptor de VCA/

Interrupteur V c.a.

(5) Interruptor térmico/

Interrupteur thermique

(6) Enchufe/Prise

Power Cord/

Cable de alimentación/

Cordon électrique

Thermal Switch

(5)

Motor

Moteur

White

Blanco/Blanc

White/Blanco/Blanc

S1 = Switch 1

(1)

S2 = Switch 2

(2)

VAC = VAC Switch

(4)

T/S = Thermal Switch

(5)

T = Thermostat

Neutral

Neutro

Neutre

White

Blanco

Blanc

Black

Negro/Noir

Black

Negro/Noir

Black

Negro/Noir

Black

Negro

Noir

Black

Negro

Noir

Blue

Azul

Bleu

Blue/Azul/Bleu

T

L1

DSI

VAC

S2

Receptacle

(6)

S1

Solenoid

Valve

Ignitor

Encendedor

Allumeur

Orange

Naranja

T/S

L2

Red/Rojo

Rouge

Red

Rojo

Rouge

La page charge ...

Master TB118A Le manuel du propriétaire

Ce manuel convient également à

Master TB118A Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents