Danby DPA120B9IWDB-6 Le manuel du propriétaire

DANBY PRODUCTS LIMITED, ONTARIO, CANADA N1H 6Z9

DANBY PRODUCTS INC., FINDLAY, OHIO, USA 45840

OWNER’S MANUAL

MANUEL DU PROPRIÉTAIRE

MANUAL DEL PROPIETARIO

www.Danby.com

*

PORTABLE AIR CONDITIONER

Owner’s Manual.............................1 - 26

CLIMATISEUR PORTABLE

Manuel du propriétaire.................27 - 52

AIRE ACONDICIONADO PORTÁTIL

Manual del propietario.................53 - 78

MODEL • MODÈLE • MODELO

DPA100B9IWDB-6

DPA120B9IWDB-6

DPA120B9IBDB-6

2020.12.28

1

Welcome to the Danby family.

We are proud of our quality products and we believe in dependable service. We suggest

that you read this owner’s manual before plugging in your new appliance as it contains

important operation information, safety information, troubleshooting, and maintenance tips

to ensure the reliability and longevity of your appliance.

You are entitled to the warranty coverage as described in the owner’s manual provided with

your new appliance.

1. Please write down your appliance information below. You must keep the original proof

of purchase receipt to validate and receive warranty services.

2. Register your product online and receive a FREE 2 MONTH WARRANTY EXTENSION

after ﬁ lling out a product survey, at www.danby.com/support/product-registration/

Need Help?

1. Read your Owner’s Manual for installation help, troubleshooting, and maintenance

assistance.

2. Visit www.Danby.com to access self-service tools, FAQs and much more by searching

your model number in the search bar.

3. For the Quickest Customer Service, please ﬁ ll out the web form at www.danby.com/

support. Your submission will go directly to an expert on your particular appliance.

Our average response times are between 20 minutes and 2 hours, during EST business

hours.

4. Call 1-800-263-2629 - please note that during peak hours, hold times can exceed one

hour.

Model Number: ____________________________________________________

Serial Number: ____________________________________________________

Date of Purchase: __________________________________________________

Important Safety Information

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS!

CAUTION: RISK OF FIRE

Flammable refrigerant used. When maintaining

or disposing of the air conditioner, the refrigerant

must not be allowed to vent into the open air.

WARNING Shows that the appliance uses a ﬂ ammable refrigerant. If the

refrigerant leaks and is exposed to an external ignition source, there is

a risk of ﬁ re.

CAUTION Shows that the operation manual should be read carefully.

CAUTION Shows that service personnel should be handling this equipment with

reference to the installation manual.

CAUTION Shows that the information is available such as the operating manual

or the installation manual.

SAVE THESE INSTRUCTIONS!

Important Safety Information

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

SAFETY PRECAUTIONS

WARNING

• Installation must be performed according to the installation instructions. Improper installation can cause

water leakage, electrical shock or ﬁ re.

• Use only the included accessories and parts and speciﬁ ed tools for the installation. Using non-standard

parts can cause water leakage, electrical shock, ﬁ re and injury or property damage.

• Make sure that the outlet you are using is grounded and has the appropriate voltage. The power cord

is equipped with a three-prong grounding plug to protect against shock. Voltage information can be

found on the nameplate of the unit.

• You unit must be used in a properly grounded wall receptacle. if the wall receptacle you intend to use is

not adequately grounded or protected by a time delay fuse or circuit breaker (the fuse of circuit breaker

needed is determined by the maximum current of the unit. The maximum current is indicated on the

nameplate located on the unit), have a qualiﬁ ed electrician install the proper receptacle.

• Install the unit on a ﬂ at, sturdy surface. Failure to do so could result in damage or excessive noise and

vibration.

• The unit must be kept free from obstruction to ensure proper function and to mitigate safety hazards.

• Do not modify the length of the power cord or use an extension cord to power the unit.

• Do not share a single outlet with other electrical appliances. Improper power supply can cause ﬁ re or

electrical shock.

• Do not install you air conditioner in a wet room such as a bathroom or laundry room. Too much

exposure to water can cause electrical components to short circuit.

• Do not install the unit in a location that may be exposed to combustible fas as this could cause ﬁ re.

• The unit has wheels to facilitate moving. Make sure not to use the wheels on thick carpet or to roll over

objects as this could cause tipping.

• Do not operate a unit that been dropped or damaged.

• The appliance with the electric heater shall have at least 1 meter space from combustible materials.

• Do not touch the unit with wet or damp hands or when barefoot.

• If the air conditioner is knocked over during use, turn off the unit and unplug it from the main power

supply immediately. Visually inspect the unit to ensure there is no damage. If you suspect the unit has

been damaged contact a technician or customer service for assistance.

• In a thunderstorm, the power must be cut off to avoid damage to the machine due to lightning.

• You air conditioner should be used in such a way that it is protected from moisture. e.g. condensation,

splashed water, etc. Do not place or store you air conditioner where it can fall or be pulled into water

or any other liquid. Unplug immediately if this occurs.

• All wiring must be performed strictly in accordance with the wiring diagram location inside the unit.

• The units circuit board (PCB) is designed with a fuse to provide over current protection. The

speciﬁ cations of the fuse are printed on the circuit board.

• When the water drainage function is not in use keep the upper and lower drain plugs ﬁ rmly installed in

the unit. The drain plugs can be a choking hazard to children.

Important Safety Information

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS!

CAUTION

• This appliance is not intended for use by persons (including children) whose physical, sensory or

mental capabilities may be different or reduced, or who lack experience or knowledge, unless such

persons receive supervision or training to operate the appliance by a person responsible for their

safety. Children should be supervised to ensure that they do not play with the appliance. Children must

be supervised around the unit at all times.

• If the power supply cord is damaged it must be replaced by the manufacturer, its service agent or

similarly qualiﬁ ed persons in order to avoid a hazard.

• Prior to cleaning or other maintenance, the appliance must be disconnected from the power supply.

• Do not remove any ﬁ xed covers. Never use this appliance if it is not working properly or if it has been

dropped or damaged.

• Do not run cord under carpeting. Do not cover cord with throw rugs, runners or similar coverings. Do

not route cord under furniture or appliances. Arrange cords away from trafﬁ c and where it will not be

tripped over.

• Do not operate a unit with a damaged power cord, plug, power fuse or circuit breaker. Discard the unit

or return to an authorized service facility for examination and/or repair.

• To reduce the risk of ﬁ re or electric shock do not use this air conditioner with any solid-state speed

control device.

• The appliance shall be installed in accordance with national wiring regulations.

• Contact the authorized service technician for repair or maintenance of this unit.

• Contact the authorized service installer for installation of this unit.

• Do not cover or obstruct the inlet or outlet grilles.

• Do not use this product for functions other than those described in this instruction manual.

• Before cleaning turn off the power and unplug the unit.

• Disconnect the power if strange sounds, smells or smoke comes from it.

• Do not press the buttons on the control panel with anything other than your ﬁ ngers.

• Do not remove any ﬁ xed covers. Never use this appliance if it is not working properly or if it has been

dropped or damaged.

• Do not operate or stop the unit by inserting or pulling out the power cord plug.

• Do not use hazardous chemicals to clean or come into contact with the unit. Do not use the unit in the

presence of inﬂ ammable substances or vapour such as alcohol, insecticides, petrol, etc.

• Always transport your air conditioner in a vertical position and stand on a stable, level surface during

use.

• Always contact a qualiﬁ ed person to carry out repairs. If the damaged power supply cord must be

replaced with a new power supply cord obtained from the product manufacturer and not repaired.

• Hold the plug by the head of the power plug when removing it.

• Turn off the appliance when not in use.

Important Safety Information

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS!

Note about ﬂ uorinated gasses

• Fluorinated greenhouse gases are contained in hermetically sealed equipment. For speciﬁ c information

on the type, the amount and the C02 equivalent in tonnes of the ﬂ uorinated greenhouse gas on some

models. Please refer to the relevant label on the unit itself.

• Installation, service, maintenance and repair of this unit must be performed by a certiﬁ ed technician.

• Product installation and recycling must be performed by a certiﬁ ed technician.

WARNING for using R32 refrigerant

• Do not use means to accelerate the defrosting process or to clean other than those recommended by the

manufacturer.

• The appliance shall be stored in a room without continuously operating ignition sources for example,

open ﬂ ames, an operating gas appliance or an operating electric heater.

• Do not pierce or burn.

• Be aware that the refrigerants may not contain an odour.

• The appliance should be installed, operated and stored in a room with a ﬂ oor area according to the

amount of refrigerant to be charged. For speciﬁ c information on the type of gas and the amount,

please refer to the relevant label on the unit itself. When there are differences between the label and the

manual on the minimum room area description, the description on the label shall prevail.

• Compliance with national gas regulations shall be observed.

• Keep ventilation openings clear of obstruction.

• The appliance shall be stored so as to prevent mechanical damage from occurring.

• A warning that the appliance shall be stored in a well-ventilated area where the room size corresponds

to the room area as speciﬁ ed for operation.

• Any person involved with working on the refrigerant circuit should hold a current, valid certiﬁ cate from

an industry accredited assessment authority which authorizes their competence to handle refrigerants

safely in accordance with an industry recognized assessment speciﬁ cation.

• Servicing shall only be performed as recommended by the manufacturer. Maintenance and repair

requiring the assistance of other skilled personnel shall be carried out under the supervision of the

person competent in the use of ﬂ ammable refrigerants.

• Please follow the instruction carefully to handle, install, clear and service the air conditioner to

avoid any damage or hazard. Flammable refrigerant R32 is used within this air conditioner. When

maintaining or disposing of the air conditioner the refrigerant must be recovered properly and should

not be allowed to discharge to the air directly.

• No open ﬁ re or device like switch which may generate spark/arcing shall be around air conditioner to

avoid causing ignition of the ﬂ ammable refrigerant used.

• Please follow the instruction carefully to store or maintain the air conditioner to prevent mechanical

damage from occurring.

• Flammable refrigerant -R32 is used in air conditioner. Please follow the instruction carefully to avoid

any hazard. For speciﬁ c information on the type of gas and the amount, please to the relevant label on

the unit itself.

• The appliance shall be stored in a room without continuously operating open ﬂ ames (for example an

operating gas appliance) and ignition sources (for example an operating electric heater).

Important Safety Information

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS!

Transport of equipment containing ﬂ ammable refrigerants

See transport regulations.

Marking of equipment using signs

See local regulations.

Disposal of equipment using ﬂ ammable refrigerants

See national regulations.

Storage of equipment / appliances

The storage of equipment should be in accordance with the manufacturer’s instructions.

Storage of packed (unsold) equipment

Storage package protection should be constructed such that the mechanical damage to the equipment

inside the package will not cause a leak of the refrigerant charge. The maximum number of pieces of

equipment permitted to be stored together will be determined by local regulations.

Information on servicing

1. Checks to the area: Prior to beginning work on systems containing ﬂ ammable refrigerants, safety

checks are necessary to ensure that the risk of ignition is minimized. For repair to the refrigerating

system, the following precautions shall be complied with prior to conducting work on the system.

2. Work procedure: Work shall be undertaken under a controlled procedure so as to minimize the risk of

a ﬂ ammable gas or vapour being present while the work is being performed.

3. General work area: All maintenance staff and others working in the local area shall be instructed on

the nature of work being carried out. Work in conﬁ ned spaces shall be avoided. The area around the

work space shall be sectioned off. Ensure that the conditions within the work area have been made safe

by removing all ﬂ ammable material.

4. Checking for the presence of refrigerant: The area shall be checked with an appropriate refrigerant

detector prior to and during work to ensure the technician is aware of potentially ﬂ ammable

atmospheres. Ensure that the leak detection equipment being used is suitable for use with ﬂ ammable

refrigerants, i.e. non-sparking, adequately sealed and intrinsically safe.

5. Presence of ﬁ re extinguisher: If any hot work is to be conducted on the refrigeration equipment or

any associated parts, appropriate ﬁ re extinguishing equipment shall be available to hand. Have a dry

powder or C0

2

ﬁ re extinguisher adjacent to the work area.

SAVE THESE INSTRUCTIONS!

Important Safety Information

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

6. No ignition sources: No person carrying out work in relation to a refrigeration system which involves

exposing any pipe work that contains or has contained ﬂ ammable refrigerant shall use any sources

of ignition in such a manner that it may lead to risk of ﬁ re or explosion. All possible ignition sources

including cigarette smoking, should be kept sufﬁ ciently far away from the site of installation, repairing,

removing and disposal during which ﬂ ammable refrigerant can possibly be released to the surrounding

space. Prior to work taking place, the area around the equipment is to be surveyed to make sure there

are no ﬂ ammable hazards or ignition risks. No smoking signs shall be displayed.

7. Ventilated area: Ensure that the area is in the open or that it is adequately ventilated before breaking

into the system or conducting any hot work. A degree of ventilation shall continue during the period

that the work is carried out. The ventilation should safely disperse any released refrigerant and

preferable expel it externally into the atmosphere.

8. Checks to the refrigeration equipment: Where electrical components are being changed, they shall

be ﬁ t for the purpose and to the correct speciﬁ cation. At all times the manufacturer’s maintenance and

service guidelines shall be followed. If in doubt consult the manufacturer’s technical department for

assistance.

The following checks shall be applied to installations using ﬂ ammable refrigerants:

• The charge size is in accordance with the room size within which the refrigerant containing parts are

installed.

• The ventilation machinery and outlets are operating adequately and are not obstructed.

• If an indirect refrigerating circuit is being used, the secondary circuit shall be checked for the presence

of refrigerant.

• Marking to the equipment continues to be visible and legible. Markings and signs that become illegible

must be corrected.

• Refrigeration pipe or components are installed in a position where they are unlikely to be exposed

to any substance which may corrode refrigerant containing components, unless the components are

constructed of materials which are inherently resistant to being corroded or are suitable protected

against being corroded.

9. Checks to electrical devices: Repair and maintenance to electrical components shall include initial

safety checks and component inspection procedures. If a fault exists that could compromise safety, then

no electrical supply shall be connected to the circuit until it is satisfactorily dealt with. If the fault cannot

be corrected immediately but it is necessary to continue operation, an adequate temporary solution

shall be used. This shall be reported to the owner of the equipment so all parties are advised.

Initial safety checks shall include:

• That capacitors are discharged. This shall be done in a safe manner to avoid possibility of sparking.

• That no live electrical components and wiring are exposed while charging, recovering or purging the

system.

• That there is continuity of earth bonding.

SAVE THESE INSTRUCTIONS!

Important Safety Information

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

Repairs to sealed components

1. During repairs to sealed components, all electrical supplies shall be disconnected from the equipment

being worked upon prior to any removal of sealed covers, etc. If it is absolutely necessary to have an

electrical supply to equipment during servicing then a permanently operating form of leak detection

shall be located at the most critical point to warn of a potentially hazardous situation.

2. To ensure that by working on electrical components the casing is not altered in such a way that the level

of protection is affected, particular attention shall be paid to the following:

• Damage to cables, excessive number of connections, terminals not made to original speciﬁ cation,

damage to seals, incorrect ﬁ tting of glands, etc.

• Ensure the apparatus is mounted securely.

• Ensure that seals or sealing materials have not degraded such that they no longer serve the purpose of

preventing the ingress of ﬂ ammable atmospheres. Replacement parts shall be in accordance with the

manufacturer’s speciﬁ cations.

Note: The use of silicon sealant may inhibit the effectiveness of some types of leak detection equipment.

Intrinsically safe components do not have to be isolated prior to working on them.

Repair to intrinsically safe components

Do not apply any permanent inductive or capacitance loads to the circuit without ensuring that this

will not exceed the permissible voltage and current permitted for the equipment in use. Intrinsically

safe components are the only types that can be worked on while live in the presence of a ﬂ ammable

atmosphere. The test apparatus shall be at the correct rating. Replace components only with parts speciﬁ ed

by the manufacturer. Other parts may result in the ignition of refrigerant in the atmosphere from a leak.

Cabling

Check that cabling will not be subject to wear, corrosion, excessive pressure, vibration, sharp edges or any

other adverse environmental effects. The check shall also take into account the effects of aging or continual

vibration from sources such as compressors or fans.

Detection of ﬂ ammable refrigerants

Under no circumstances shall potential sources of ignition be used in the searching for or detection of

refrigerant leaks. A halide torch or any other detector using a naked ﬂ ame shall not be used.

SAVE THESE INSTRUCTIONS!

Important Safety Information

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

Leak detection methods

The following leak detection methods are deemed acceptable for systems containing ﬂ ammable

refrigerants:

• Electronic leak detectors shall be used to detect ﬂ ammable refrigerants but the sensitivity may not be

adequate or may need recalibration. Detection equipment shall be calibrated in a refrigerant-free area.

Ensure that the detector is not a potential source of ignition and is suitable for the refrigerant used.

• Leak detection equipment shall be set at a percentage of the LFL of the refrigerant and shall be

calibrated to the refrigerant employed and the appropriate percentage of gas (25% maximum) is

conﬁ rmed.

• Leak detection ﬂ uids are suitable for use with most refrigerants but the use of detergents containing

chlorine shall be avoided as the chlorine may react with the refrigerant and corrode the copper or

pipe-work.

• If a leak is suspected, all naked ﬂ ames shall be removed or extinguished.

• If a leakage of refrigerant is found which requires brazing, all of the refrigerant shall be recovered

from the system or isolated by means of shut off valves in a part of the system remote from the leak.

Oxygen free nitrogen (OFN) shall then be purged through the system both before and during the

brazing process.

Removal and evacuation

When breaking into the refrigerant circuit to make repairs or for any other purpose conventional

procedures shall be used. However, it is important that the best practice is followed since ﬂ ammability is a

consideration. The following procedures shall be adhered to:

• Remove refrigerant.

• Purge the circuit with inert gas.

• Evacuate.

• Purge again with inert gas.

• Open the circuit by cutting or brazing.

• The refrigerant charge shall be recovered into the correct recovery cylinders. The system shall be

ﬂ ushed with OFN to render the unit safe. This process may need to be repeated several times.

Compressed air or oxygen shall not be used for this task.

• Flushing shall be achieved by breaking the vacuum in the system with OFN and continuing to ﬁ ll until

the working pressure is achieved, then venting to atmosphere and ﬁ nally pulling down to a vacuum.

This process shall be repeated until no refrigerant is within the system. When the ﬁ nal OFN charge

is used, the system shall be vented down to atmospheric pressure to enable work to take place. This

operation is absolutely vital is brazing operations on the pipe-work are to take place.

• Ensure that the outlet for the vacuum pump is not close to any ignition sources and there is ventilation

available.

SAVE THESE INSTRUCTIONS!

Important Safety Information

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

Charging procedures

In addition to conventional charging procedures, the following requirements shall be followed:

• Ensure that contamination of different refrigerants does not occur when using charging equipment.

Hoses or lines shall be as short as possible to minimize the amount of refrigerant contained in them.

• Cylinders shall be kept upright.

• Ensure that the refrigeration system is earthed prior to charging the system with refrigerant.

• Label the system when charging is complete, if not already labeled.

• Extreme care shall be taken not to overﬁ ll the refrigeration system.

• Prior to recharging the system it shall be pressure tested with OFN. The system shall be leak tested on

completion of charging but prior to commissioning. A follow up leak test shall be carried out prior to

leaving the site.

Decommissioning

Before carrying out this procedure, it is essential that the technician is completely familiar with the

equipment in all its detail. It is recommended good practice that all refrigerants are recovered safely. Prior

to the task being carried out, an oil and refrigerant sample shall be taken in case analysis is required

prior to re-use of reclaimed refrigerant. It is essential that electrical power is available before the task is

commenced.

A. Become familiar with the equipment and its operation.

B. Isolate system electrically.

C. Before attempting the procedure ensure that:

• Mechanical handling equipment is available if required for handling refrigerant cylinders.

• All personal protective equipment is available and being used correctly.

• The recovery process is supervised at all times by a competent person.

• Recovery equipment and cylinders conform to the appropriate standards.

D. Pump down refrigerant system, if possible.

E. If a vacuum is not possible, make a manifold so that refrigerant can be removed from various parts of

the system.

F. Make sure that cylinder is situated on the scales before recovery takes place.

G. Start the recovery machine and operate in accordance with the manufacturer’s instructions.

H. Do not overﬁ ll cylinders. No more than 80% volume liquid charge.

I. Do not exceed the maximum working pressure of the cylinder, even temporarily.

J. When the cylinders have been ﬁ lled correctly and the process is completed, make sure that the cylinders

and the equipment are removed from the site promptly and all isolation valves on the equipment are

closed off.

K. Recovered refrigerant shall not be charged into another refrigeration system unless it has been cleaned

and checked.

SAVE THESE INSTRUCTIONS!

Important Safety Information

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

Labeling

Equipment shall be labeled stating that it has been decommissioned and emptied of refrigerant. The label

shall be dated and signed. Ensure that there are labels on the equipment stating the equipment contains

ﬂ ammable refrigerant.

Recovery

When removing refrigerant from a system, either for servicing or decommissioning, it is recommended

good practice that all refrigerants are removed safely.

When transferring refrigerant into cylinders, ensure that only appropriate refrigerant recovers cylinders are

employed. Ensure that the correct number of cylinders for holding the total system charge are available.

All cylinders to be used are designed for the recovered refrigerant and labeled for that refrigerant, i.e.

special cylinders for the recovery of refrigerant. Cylinders shall be complete with pressure relief valve and

associated shut-off valves in good working order. Empty recovery cylinders are evacuated and, if possible,

cooled before recovery occurs.

The recovery equipment shall be in good working order with a set of instructions concerning the equipment

that is at hand and shall be suitable for the recovery of ﬂ ammable refrigerants. In addition, a set of

calibrated weighing scales shall be available and in good working order. Hoses shall be complete with

leak-free disconnect couplings and in good condition. Before using the recovery machine, check that is it

in satisfactory working order, has been properly maintained and that any associated electrical components

are sealed to prevent ignition in the event of a refrigerant leak. Consult the manufacturer if in doubt.

The recovered refrigerant shall be returned to the refrigerant supplier in the correct recovery cylinder

and the relevant waste transfer note shall be arranged. Do not mix refrigerants in recovery units and

especially not in cylinders. If compressors or compressor oils are to be removed, ensure that they have

been evacuated to an acceptable level to make certain that ﬂ ammable refrigerant does not remain within

the lubricant. The evacuation process shall be carried out prior to returning the compressor to the suppliers.

Only electric heating to the compressor body shall be employed to accelerate this process. When oil is

drained form a system, it shall be carried out safely.

INSTALLATION INSTRUCTIONS

12

ACCESSORIES

1. Air outlet adapter

2. Exhaust adapter module A

3. Exhaust adapter module B

4. Exhaust adapter module C

5. Exhaust adapter screw

6. Window slider A

7. Window slider B

8. Window slider C

9. Window slider bolts (x4)

10. Foam seal A (adhesive) (x2)

11. Foam seal B (adhesive) (x2)

12. Foam seal C (non-adhesive) (x2)

13. Security bracket and 2 screws

14. Drain hose

15. Remote control and batteries

16. Power cord buckle

REQUIRED TOOLS

1. Medium sized Phillips screwdriver

2. Tape measure or ruler

3. Knife or scissors

4. Saw (in the event that the window sliders need to

be cut to size)

1

2

3

4

5

6

7

8

9

10

11

12

13

ON/OFF

TEM P

S

H

C

O

U

R

T

O

IM

N

ER

T

O

IM

F

E

F

R

MODE

FAN

SLEEP

SW IN G

LED

14

15

16

IMPORTANT WARNING

Do not leave this appliance unattended

in a space where people or animals who

cannot react to a malfunction are located. A

malfunction such as the exhaust hose becoming

dislocated, can cause extreme overheating or

death in an enclosed, unattended space.

INSTALLATION INSTRUCTIONS

13

WINDOW KIT ASSEMBLY

Step one: prepare the window sliders

1. Measure the window opening where the window

kit will be installed.

2. Assemble as many sliders as necessary to ﬁ t the

window. If the window opening is less than the

minimum length of a single slider, use the slider

that has the hole in it and cut it to the correct

length. Make sure not to cut the end that has the

hole as this is necessary to attach the exhaust

hose adapter.

3. Use the window slider bolts to secure the

window sliders at the correct length.

Step two: prepare the exhaust adapter (for

optional sliding window applications)

Assemble the exhaust adapter module for sliding

windows using the exhaust adapter screw as shown.

The window slider is eccentric so the exhaust

adapter must be installed away from the wall.

Bolt

Bolts

B

A

C

B

A

B

C

A

screw

EXHAUST HOSE

Pull out the hose

1. Rotate the exhaust hose gently backwards.

2. Pull out the exhaust hose.

14

INSTALLATION INSTRUCTIONS

INSTALLING THE WINDOW KIT

The instructions below can be used for a hung window application (shown on the left) or an optional

sliding window application (shown on the right).

1. Cut adhesive foam seals A and B to the correct lengths and attach them to the window frame as shown.

B

A

B

A

2. Insert the window slider kit into the window opening and close the window the secure it in place.

A

B

A

B

3. Cut the non-adhesive foam seal C to match the width or height of the window and insert it between the

panes of glass as shown to prevent outside air from entering the window.

C

15

INSTALLATION INSTRUCTIONS

4. If desired, install the security bracket with 2 screws as shown.

5. For a hung window, attach the air outlet adapter onto the exhaust hose and rotate it 90° to secure it in

place. For a sliding window, attach the exhaust adapter onto the exhaust hose.

12

6. For a hung window, attach the air outlet adapter onto the window slider kit. For a sliding window,

attach the exhaust adapter onto the window slider kit.

16

OPERATING INSTRUCTIONS

FEATURES

1. Control panel

2. Handle (both sides)

3. Casters

4. Upper air ﬁ lter

5. Upper air intake

6. Exhaust hose

7. Continuous drain

8. Power cord storage band

9. Bottom tray drain

1

2

3

4

5

6

7

8

9

LOCATION

Place the air conditioner on a smooth, level ﬂ oor

that is strong enough to support it and all included

accessories.

Make sure the appliance is level to minimize noise

and vibration.

The appliance must be installed near a grounded

receptacle and the overﬂ ow drain outlet on the rear

of the appliance must be accessible.

Do not cover air inlets or outlets or the remote

control receiver on the control panel.

The appliance requires 25 cm (10 inches) of space

from the nearest wall and the back for proper

operation. The louver blade should be 50 cm (20

inches) away from obstacles.

17

OPERATING INSTRUCTIONS

CONTROL PANEL

1. Swing and wireless connect button:

• Press to start the auto swing feature.

• Press and hold for three seconds to start using the wireless connect feature.

2. Timer button: Press to set the automatic timer. Light will indicate whether a timer is set.

3. Mode button: Press to select the desired mode. Light will indicate current mode.

4. Temperature control buttons:

• Press to modify the set temperature in 1° increments in a range of 16 - 30°C (60 - 86°F).

• Press to modify the timer setting in 0.5 hour increments up to 10 hours and then in 1 hour

increments up to 24 hours.

• Press and hold both temperature control buttons for three seconds to change the temperature

display from °C to °F.

5. LED display:

• Shows the set temperature in °C or °F.

• Shows the timer settings.

• Shows error codes.

• When on fan mode, shows the room temperature.

6. Fan button:

• Press to select fan speed. Light will indicate current speed.

• Press and hold for 3 seconds to turn the continuous fan on or off.

7. Sleep and ﬁ lter button:

• Press to start the sleep feature.

• The ﬁ lter light will illuminate after 250 hours of use as a reminder to clean the ﬁ lter; to reset the ﬁ lter

after cleaning, press and hold the sleep button for three seconds.

8. Power button: Press to turn the appliance on or off.

3sec

REMOTE CONTROL

1. Power button: Press to turn the appliance on or

off.

2. Mode button: Press to select the desired mode.

3. Fan button: Press to select fan speed.

4. Sleep button: Press to start the sleep feature.

5. Swing button: Press to start the auto swing

feature. When auto swing is activated, press

again to stop the louver at the desired angle.

6. Follow me button: Press to activate the follow me

feature.

7. LED button: Press to turn the LED display on or

off.

8. Timer off button: Press to set the automatic off

timer.

9. Timer on button: Press to set the automatic on

timer.

10. Shortcut button: Press to set and activate the

short cut function.

11. Temperature control buttons:

• Used to set the temperature.

• Press and hold both temperature control buttons

for 3 seconds to change the temperature display

from °C to °F.

12. LED display:

• Shows the set temperature in °C or °F or the

auto-timer settings.

• Shows whether the follow me function is active.

SHORTCUT FUNCTION

The shortcut function can be used to save a favourite

setting.

To set a favourite, set the appliance to the desired

temperature and fan speed. Press and hold the

shortcut button for 2 seconds. Press the shortcut

button at any point in future to return to the

favourite setting.

If no favourite is set, pressing the shortcut button will

cause the appliance to run in auto mode at 29°C

(79°F), with fan speed set to auto.

The shortcut function is only available on the remote

control.

OPERATING INSTRUCTIONS

18

TEMP

OPERATING INSTRUCTIONS

This equipment has been tested and found to

comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits

are designed to provide reasonable protection

against harmful interference in a residential

installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may

cause harmful interference to radio communications.

However, there is no guarantee that interference will

not occur in a particular installation.

If this equipment does cause harmful interference

to radio or television reception, which can be

determined by turning the equipment off and on, the

user is encouraged to try to correct the interference

by one or more of the following measures:

1. Reorient or relocate the receiving antenna

2. Increase the separation between the equipment

and receiver

3. Connect the equipment into an outlet on a

circuit different from that to which the receiver is

connected

4. Consult the dealer or an experienced radio/TV

technician for help

Changes or modiﬁ cations not approved by the

party responsible for FCC compliance could void

the user’s authority to operate the equipment. This

appliance complies with Part 15 of the FCC Rules.

Operation is subject to the following conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference

received, including interference that may cause

undesired operation.

This device complies with Canadian CAN ICES-3

(B) / NMB-3 (B)

REPLACING THE REMOTE BATTERIES

This air conditioner comes with two AAA batteries.

Place the batteries in the remote control before use.

1. Slide the back cover from the remote downward

to expose the battery compartment.

2. Insert the batteries, ensure to match the (+) and

(-) symbols on the ends of the batteries with the

symbols inside the battery compartment.

3. Slide the battery cover back into place.

Notes:

• The air conditioner will not respond if curtains,

doors or other materials block the signal from

the remote control to the unit.

• Prevent any liquid from contact with the remote

control. Do not expose the remote control to

direct sunlight or heat.

• If the infrared signal receiver on the indoor unit

is exposed to direct sunlight, the air conditioner

may not function properly. Use curtains to

prevent the sunlight from falling on the receiver.

• Do not mix old and new batteries or batteries of

different types.

• Do not leave the batteries in the remote control

if it is not going to be used for more than 2

months.

IMPORTANT

Do not dispose of batteries as unsorted municipal

waste. Refer to local laws for proper disposal of

batteries.

19

La page est en cours de chargement...

Danby DPA120B9IWDB-6 Le manuel du propriétaire

Ce manuel convient également à

Danby DPA120B9IWDB-6 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents