Danby DDR095BDPWDB Le manuel du propriétaire

Catégorie
Déshumidificateurs
Taper
Le manuel du propriétaire
DANBY PRODUCTS LIMITED, ONTARIO, CANADA N1H 6Z9
DANBY PRODUCTS INC., FINDLAY, OHIO, USA 45840
OWNER’S MANUAL
MANUEL DU PROPRIÉTAIRE
MANUAL DEL PROPIETARIO
DEHUMIDIFIER
Owner’s Manual...............................1 - 9
DÉSHUMIDIFICATEUR
Manuel du propriétaire.................10 - 18
DESHUMIDIFICADOR
Manual del propietario.................19 - 27
MODEL MODÈLE MODELO
DDR095BDPWDB
2018.01.24
Welcome
Welcome to the Danby family. We are proud of our quality products and we believe in
dependable service. We suggest that you read this owner’s manual before plugging in your new
appliance as it contains important operation information, safety information, troubleshooting and
maintenance tips to ensure the reliability and longevity of your appliance.
Visit www.Danby.com to access self service tools, FAQs and much more. For additional assistance
call 1-800-263-2629.
Note the information below; you will need this information to obtain service under warranty.
You must provide the original purchase receipt to validate your warranty and receive service.
Model Number: _________________________________________________
Serial Number: _________________________________________________
Date of Purchase: _______________________________________________
Need Help?
Before you call for service, here are a few things you can do to help us serve you better.
Read this owner’s manual:
It contains instructions to help you use and maintain your appliance properly.
If you receive a damaged appliance:
Immediately contact the retailer or builder that sold you the appliance.
Save time and money:
Check the troubleshooting section at the end of this manual before calling. This section
will help you solve common problems that may occur.
1-800-26- Danby
(1-800-263-2629)
1
SAFETY REQUIREMENTS
This appliance is not intended for use by persons
(including children) whose physical, sensory or
mental capabilities may be different or reduced,
or who lack experience or knowledge, unless such
persons receive supervision or training to operate
the appliance by a person responsible for their
safety.
Children should be supervised to ensure that they
do not play with the appliance.
To avoid risk of electric shock, do not operate this
dehumidifi er in an area that is likely to accumulate
standing water. If this condition develops, disconnect
the power supply before stepping into the water.
Do not store or use combustible materials such as
gasoline or other fl ammable vapors or liquids in the
vicinity of this or any other appliance.
Do not insert fi ngers or other objects into grills or
openings in the appliance.
Do not cover or block the intake and exhaust
openings.
Do not operate the appliance without the fi lter
installed.
Do not operate the appliance near heat sources.
This appliance is intended for indoor, residential
applications only. Do not use this dehumidifi er
outdoors. Do not use this dehumidifi er for
commercial or industrial applications.
GROUNDING INSTRUCTIONS
This appliance must be grounded. Grounding
reduces the risk of electrical shock by providing an
escape wire for the electrical current.
This appliance has a cord that has a grounding
wire with a 3-prong plug. The power cord must be
plugged into an outlet that is properly grounded.
If the outlet is a 2-prong wall outlet, it must be
replaced with a properly grounded 3-prong wall
outlet. The serial rating plate indicates the voltage
and frequency the appliance is designed for.
WARNING - Improper use of the grounding
plug can result in a risk of electric shock.
Consult a qualifi ed electrician or service agent
if the grounding instructions are not completely
understood, or if doubt exists as to whether the
appliance is properly grounded.
Do not connect the appliance to extension cords,
adapters or together with another appliance in the
same wall outlet.
Do not splice the power cord. Do not under any
circumstances cut or remove the third ground prong
from the power cord.
If the power supply cord is damaged, it must be
replaced by the manufacturer, its service agent or
similar qualifi ed person in order to avoid hazard.
Important Safety Information
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
2
SAVE THESE INSTRUCTIONS!
OPERATING INSTRUCTIONS
LOCATION
Place the dehumidifi er on a smooth, level fl oor
that is strong enough to support the appliance
with a full bucket of water.
To maintain ef ciency, operate the appliance
in an enclosed area. Keep nearby doors and
windows closed.
Maintain a minimum clearance of 20 cm (8
inches) on the sides and back of the appliance
and 40 cm (16 inches) on the top of the
appliance to allow for proper air circulation.
The recommended ambient operating
temperature is between 5°C (41°F) and 35°C
(95°F).
Do not force rollers to move over carpeting as
the appliance may tip over and spill water.
Any time the appliance is placed on its back or
side, it must be allowed to stand upright for 6
hours before plugging in to avoid damage to
internal components.
FEATURES
Front
1. Air Outlet
2. Control Panel
3. Handles (both sides)
4. Water Bucket
Back
1. Air Inlet
2. Continuous Drain Outlet
3. Power Cord Storage Band
4. Pump Drain Outlet
5. Power Cord
1
2
3
4
1
2
3
4
5
3
CONTROL PANEL
1. Continuous Mode Button and Indicator Light
Press this button to activate continuous mode.
This will run the dehumidifying function
continuously. The indicator light will turn on
when continuous mode is active.
2. Timer Button and Indicator Lights
Use this button to set the timer function.
3. Defrost Indicator Light
The defrost indicator light will illuminate
when frost has accumulated on the interior
of the appliance. This can indicate that
the ambient temperature is too cold. The
dehumidifying function will cease until the
frost has melted.
4. Full Bucket Indicator Light
The full bucket indicator light will illuminate
when the bucket is full of water. Empty the
bucket to resume regular functioning.
5. Display and Up and Down Arrows
The display will show the set humidity, the
ambient humidity or the timer function.
The up and down arrows can adjust the set
humidity or the timer setting.
The humidity can be set between 35-85% in
5% increments. For drier air, set the humidity
to a lower number. For damper air, set the
humidity to a higher number.
The ambient humidity display is accurate
within +/- 5%.
OPERATING INSTRUCTIONS
1
2 3 4
5
6
7 8 9
10
11
4
6. Power Button
Use this button to turn the appliance on or
off.
7. Pump Button and Indicator Light
Use this button to activate the drain pump.
The indicator light will illuminate when the
pump is active.
8. Smart Dehumidify Button and Indicator Light
Use this button to activate smart dehumidify
mode. Smart dehumidify will automatically
set the humidity and fan speed based on
the ambient temperature and humidity. The
indicator light will illuminate when comfort
mode is active.
9. Filter Button and Indicator Light
• The lter light will illuminate when the fi lter
needs to be cleaned. Press the fi lter button
once the fi lter has been cleaned to return to
regular functioning.
10. Fan Button and Indicator Light
Press this button to set the fan speed to low
or high. If the indicator light is off, the fan is
set to low speed. If the indicator light is on,
the fan is set to high speed.
11. Ionizer Mode Button and Indicator Light
Use this button to activate the ionizer
function. The indicator light will illuminate
when the ionizer is active.
OPERATING INSTRUCTIONS
5
TIMER FUNCTION
Auto On Function
1. Press the timer button until the auto on indicator
light illuminates.
2. Use the up and down arrows to select the
desired amount of time before the appliance
should turn on. The up and down arrows
will add or subtract 30 minutes of time up to
10 hours, then at 1 hour increments up to a
maximum of 24 hours.
3. The time selected will appear on the display
panel and will count down until the appliance
turns on.
Auto Off Function
1. Press the timer button until the auto off indicator
light illuminates.
2. Use the up and down arrows to select the
desired amount of time before the appliance
should turn on. The up and down arrows
will add or subtract 30 minutes of time up to
10 hours, then at 1 hour increments up to a
maximum of 24 hours.
3. The time selected will appear on the display
panel and will count down until the appliance
turns off.
Using Auto On and Auto Off Simultaneously
The auto on and auto off functions can be used at
the same time by fi rst setting one and then the other.
Both indicator lights will illuminate and the display
will count down to the appliance either turning off
or on, whichever function was set fi rst.
Note: The timer will not cycle the appliance on and
off indefi nitely. The auto on and auto off timers will
function one time and then the appliance will return
to regular functioning.
Turning the appliance off, pressing the default
button on the remote or unplugging the appliance
will clear all memory settings, including the timer.
IONIZER FUNCTION
The ionizer function is a form of air purifi cation that
negatively charges the air. Dust particles, pollen
and other particles in the air cannot pass through
the fi lter when they are negatively charged. This
ensures that the maximum amount of dust and dirt
are removed from the air. Additionally, the ionizer
function helps to remove unwanted odors from the
air.
WATER REMOVAL
There are three ways to remove collected water
from the appliance.
1. Water Bucket
The dehumidifi er will automatically collect
condensed water in the water bucket. When the
bucket is full, the compressor and fan will turn off
and the full bucket indicator light will turn on. The
display will show “P2”.
To empty the bucket, gently remove it from the
appliance by gripping both sides and pulling
outward. Be cautious when removing the bucket, it
will be full and can be heavy.
Do not place the water bucket directly on the fl oor.
The bottom of the bucket is uneven and it will fall
over and spill water.
Empty the bucket and replace it in the appliance.
The dehumidifi er will not function without the bucket
installed.
Note: When removing the bucket, the pump arm
for the drain pump may fall down. It must be gently
pushed upward back into the correct position before
replacing the bucket.
OPERATING INSTRUCTIONS
6
WATER REMOVAL
2. Continuous Drain
Water can be removed from the appliance using the
continuous drain and a standard garden hose (not
provided).
Before using any automatic drain functions,
check that all drain ports are clean and free of
debris. There is one drain port inside the bucket
compartment of the appliance, remove the bucket
to see it. There is one drain port on the back of the
appliance where the drain hose attaches. All drain
ports should be cleaned with a pipe cleaner prior to
use.
Note: Do not clean the drain ports with anything
more rigid than a pipe cleaner as this can damage
the appliance.
Note: If the drain ports are clogged or dirty it
can cause water to leak from the bottom of the
appliance.
Remove the cover from the continuous drain outlet
and attach the female threaded end of the garden
hose to the back of the appliance. Direct the other
end of the garden hose to a bucket or fl oor drain.
Ensure that the garden hose is not bent and goes
straight down from the back of the appliance. The
continuous drain is only activated by gravity so any
bends or upward motion in the hose will stop the
water from draining.
The garden hose should be cut so that it is no more
than 1.8 m (6 feet) long. If the drain hose is too
long water may not drain completely which can
lead to stagnant water and mildew build up inside
the hose.
WATER REMOVAL
3. Pump Drain
If the continuous drain is inconvenient, water can be
removed from the appliance using the pump drain.
When using the pump, the appliance will fi rst ll the
bucket with water and then the pump arm will pump
water from the bucket through the drain and out the
hose.
Remove the cover from the pump drain outlet and
attach the provided drain hose. Direct the other end
of the hose to a drain. Press the pump button to
activate the pump function. When the bucket is full,
the pump will begin to work.
Ensure that the drain hose is not bent, this can stop
the water from draining correctly and overwork the
pump.
Do not connect the provided hose together with
another hose. The maximum length of the pump
drain hose should be no more than 4.6 m (15 feet).
If the drain hose is too long water may not drain
completely which can lead to stagnant water and
mildew build up inside the hose.
When using the pump drain, the water bucket
should be emptied every few days to ensure that the
water in the bucket does not become stagnant or
grow mildew.
CARE & MAINTENANCE
AIR FILTER
The air fi lter should be cleaned approximately every
2 weeks. The air fi lter may require more frequent
cleaning if there is signifi cant dander or fur in the
air.
Approximately every two weeks, the fi lter indicator
light on the control panel will illuminate as a
reminder to clean the fi lter. Follow the steps below
to clean the fi lter and return the appliance to normal
functioning.
1. The air fi lter is located behind the rear intake
grill. To remove the air fi lter, grasp the fi lter tab
on the bottom of the grill and slide it downward.
2. Use a vacuum cleaner with a soft brush
attachment to remove any large debris or dust
build up from the air fi lter.
3. Wash the fi lter in lukewarm, soapy water, below
40°C (104°F), or use a neutral cleaning agent.
4. Rinse the fi lter with clean water and dry
thoroughly before reinstalling in the appliance.
5. Press the fi lter button on the control panel to
resume normal functioning.
Note: Do not operate the appliance without the air
lter installed.
ERROR CODES
If the display panel shows any of the below error
codes, unplug the appliance, let it stand for 5-10
minutes and then plug it back in. If the error
persists, call for service.
AS - Humidity sensor error
ES - Temperature sensor error
P2 - Full bucket
E3 - Sensor malfunction
Eb - Bucket removed or not in the correct position
EC - Cooling system error or sensor error
CLEANING
To avoid possible electric shock, ensure that the
appliance is unplugged before performing any
cleaning or maintenance.
The outside of the appliance can be wiped clean
with a soft cloth or with a lukewarm, damp cloth if
necessary.
Do not use gasoline, benzene, thinner or any
other chemicals to clean this appliance as these
substances can cause damage to the fi nish and
deformation of plastic parts.
Never pour water directly onto the appliance as this
will cause deterioration of electrical components
and wiring insulation.
Ensure that the drain ports on the interior of the
appliance and the drain ports on the back of the
appliance are free of dirt and calcium build up.
END OF SEASON CARE
Before removing the appliance from service for the
year, operate the appliance on high fan mode for
half a day to ensure that the inside of the appliance
is dry. This will help avoid the growth of mold or
mildew inside the appliance. Ensure the fi lter is
clean and dry. Store the appliance covered in a dry
location.
DISPOSAL
This appliance may not be treated as regular
household waste, it should be taken to the
appropriate waste collection point for recycling of
electrical components. Check for local regulatory
compliance regarding approved and safe disposal
of this appliance.
7
TROUBLESHOOTING
Danby Consumer Care: 1-800-263-2629
Hours of operation:
Monday to Thursday 8:30 am - 6:00 pm Eastern Standard Time
Friday 8:30 am - 4:00 pm Eastern Standard Time
Information in this manual is subject to change without notice.
PROBLEM POSSIBLE CAUSE
Appliance will not operate Plug is not fully inserted into the wall outlet
Blown fuse or circuit breaker
Ambient humidity is lower than the set humidity
Bucket is full or is not in the proper position
Insuffi cient dehumidifying • Air lter is dirty
Blocked air fl ow
Appliance size is too small for application
Ambient humidity is lower than the set humidity
Noise • Air lter is dirty
Bucket is not in proper position
Floor surface is not level
Odors Formation of mold or mildew on internal wet surfaces
Place an algaecide tablet in the water bucket
Water on fl oor Hose connection is loose
Drain cover has been removed
Frost build up When ambient temperature is below 5°C (41°F) frost may form
Switch the appliance to fan only mode until the frost melts
8
LIMITED IN-HOME APPLIANCE WARRANTY
This quality product is warranted to be free from manufacturer’s defects in material and workmanship, provided that the unit is used under the normal operating
conditions intended by the manufacturer.
This warranty is available only to the person to whom the unit was originally sold by Danby Products Limited (Canada) or Danby Products Inc. (U.S.A.) (hereafter
“Danby”) or by an authorized distributor of Danby, and is non-transferable.
TERMS OF WARRANTY
Plastic parts, are warranted for thirty (30) days only from purchase date, with no extensions provided.
First Year
During the rst twelve (12) months, any functional parts of this product found to be defective, will be repaired or replaced, at warrantor’s
option, at no charge to the ORIGINAL purchaser.
To obtain
Danby reserves the right to limit the boundaries of “In Home Service” to the proximity of an Authorized Service Depot. Any app liance
Service
requiring service outside the limited boundaries of “In Home Service” , it will be the consumer’s responsibility to transport the appliance (at
their own expense) to the original retailer (point of purchase) or a service depot for repair. See “Boundaries of In Home Serv ice” below.
Contact your dealer from whom your unit was purchased, or contact your nearest authorized Danby service depot, where service
must be performed by a qualied service technician.
If service is performed on the units by anyone other than an authorized service depot, or the unit is used for commercial appli cation, all
obligations of Danby under this warranty shall be void.
Boundaries of
If the appliance is installed in a location that is 100 kilometers (62 miles) or more from the nearest service center your unit must be
In Home Service
delivered to the nearest authorized Danby Service Depot, as service must only be performed by a technician qualied and certif ied for
warranty service by Danby. Transportation charges to and from the service location are not protected by this warranty and are t he
responsibility of the purchaser.
Nothing within this warranty shall imply that Danby will be responsible or liable for any spoilage or damage to food or other c ontents of this appliance, whether due
to any defect of the appliance, or its use, whether proper or improper.
EXCLUSIONS
Save as herein provided, Danby, there are no other warranties, conditions, representations or guarantees, express or implied, m ade or intended by Danby or its
authorized distributors and all other warranties, conditions, representations or guarantees, including any warranties, conditio ns, representations or guarantees
under any Sale of Goods Act or like legislation or statue is hereby expressly excluded. Save as herein provided, Danby shall no t be responsible for any damages
to persons or property, including the unit itself, howsoever caused or any consequential damages arising from the malfunction o f the unit and by the purchase of
the unit, the purchaser does hereby agree to indemnify and hold harmless Danby from any claim for damages to persons or propert y caused by the unit.
GENERAL PROVISIONS
No warranty or insurance herein contained or set out shall apply when damage or repair is caused by any of the following:
1) Power failure.
2) Damage in transit or when moving the appliance.
3) Improper power supply such as low voltage, defective house wiring or inadequate fuses.
4) Accident, alteration, abuse or misuse of the appliance such as inadequate air circulation in the room or abnormal operating con ditions
(extremely high or low room temperature).
5) Use for commercial or industrial purposes (ie. If the appliance is not installed in a domestic residence).
6) Fire, water damage, theft, war, riot, hostility, acts of God such as hurricanes, oods etc.
7) Service calls resulting in customer education.
8) Improper Installation (ie. Building-in of a free standing appliance or using an appliance outdoors that is not approved for out door application).
Proof of purchase date will be required for warranty claims; so, please retain bills of sale. In the event warranty service is required, present this document to our
AUTHORIZED SERVICE DEPOT.
Danby Products Limited
PO Box 1778, Guelph, Ontario, Canada N1H 6Z9
Telephone: (519) 837-0920 FAX: (519) 837-0449
Danby Products Inc.
PO Box 669, Findlay, Ohio, U.S.A. 45840
Telephone: (419) 425-8627 FAX: (419) 425-8629
04/09
1-800-263-2629
Warranty Service
In-home
Transportation charges to and from the service location are not protected by this warranty and are the responsibility of the purchaser.
During the first twenty four (24) months, any functional parts of this product found to be defective, will be repaired
or replaced, at warrantor’s option, at no charge to the original purchaser.
Contact the dealer where the unit was purchased, or contact the nearest authorized Danby service depot, where
service must be performed by a qualified service technician. If service is performed on the unit by anyone other
than an authorized service depot, all obligations of Danby under this warranty shall be void.
It is the responsibility of the purchaser to transport the appliance to the nearest authorized service depot.
First 24 months
To obtain service
LIMITED “CARRY IN” WARRANTY
This quality product is warranted to be free from manufacturer’s defects in material and workmanship, provided that the unit is used
under the normal operating conditions intended by the manufacturer.
This warranty is available only to the person to whom the unit was originally sold by Danby Products Limited (Canada) or Danby
Products Inc. (U.S.A.) (hereafter “Danby”) or by an authorized distributor of Danby, and is non-transferable.
TERMS OF WARRANTY
Plastic parts are warranted for thirty (30) days from the date of purchase, with no extensions provided.
Nothing within this warranty shall imply that Danby will be responsible or liable for any spoilage or damage to food or other
contents of this appliance, whether due to any defect of the appliance, or its use, whether proper or improper.
EXCLUSIONS
Save as herein provided, by Danby, there are no other warranties, conditions, representations or guarantees, express or implied, made
or intended by Danby or its authorized distributors and all other warranties, conditions, representations or guarantees, including any
warranties, conditions, representations or guarantees under any Sale of Goods Act or like legislation or statute is hereby expressly
excluded. Save as herein provided, Danby shall not be responsible for any damages to persons or property, including the unit itself,
howsoever caused or any consequential damages arising from the malfunction of the unit and by the purchase of the unit, the
purchaser does hereby agree to indemnify and hold harmless Danby from any claim for damages to persons or property caused by
the unit.
GENERAL PROVISIONS
No warranty or insurance herein contained or set out shall apply when damage or repair is caused by any of the following:
1) Power failure.
2) Damage in transit or when moving the appliance.
3) Improper power supply such as low voltage, defective house wiring or inadequate fuses.
4) Accident, alteration, abuse or misuse of the appliance such as inadequate air circulation in the room or abnormal operating
conditions (ie. extremely high or low room temperature).
5) Use for commercial or industrial purposes (ie. If the appliance is not installed in a domestic residence).
6) Fire, water damage, theft, war, riot, hostility, acts of God such as hurricanes, floods etc.
7) Service calls resulting in customer education.
8) Improper Installation (ie. Building-in of a free standing appliance or using an appliance outdoors that is not approved for outdoor
application, including but not limited to: garages, patios, porches or anywhere that is not properly insulated or climate controlled).
Proof of purchase date will be required for warranty claims; retain bills of sale. In the event that warranty service is required, present
the proof of purchase to our authorized service depot.
Warranty Service
Carry In
Danby Products Limited
PO Box 1778, Guelph, Ontario, Canada N1H 6Z9
Telephone: (519) 837-0920 FAX: (519) 837-0449
Danby Products Inc.
PO Box 669, Findlay, Ohio, U.S.A. 45840
Telephone: (419) 425-8627 FAX: (419) 425-8629
1-800-263-2629
04/17
10
Bienvenue
Bienvenue à la famille Danby. Nous sommes fi ers de la qualité de nos produits et nous croyons
en le service fi able. Nous vous suggérons de lire ce manual d’utilisation avant de brancher
votre nouvel appareil car il contient des informations inportantes sur l’utilisation, la sécurité, le
dépannage et la maintenance, afi n d’assurer la fi abilité et la longévité de votre appareil.
Visitez www.Danby.com pour accéder aux outils d’autoservice, aux FAQ et bien plus encore. Pour
obtenir de l’aide supplémentaire, composez 1-800-263-2629.
Notez les informations ci-dessous; Vous aurez besoin de cette information pour obtenir un
service sous garantie.
Vous devez fournir le reçu d’achat original pour valider votre garantie et recevoir le service.
Numéro de modèle: _____________________________________________
Numéro de serie: _______________________________________________
Date d’achat: __________________________________________________
Besoin d’assistance?
Avant d’appeler pour service, voici quelques choses que vous pouvez faire pour nous
aider à mieux vous servir.
Lire ce manuel du propriétaire:
Il contient des instructions pour vous aider à utiliser et à maintenir votre appareil
correctement.
Si vous recevez un appareil endommagé:
Contactez immédiatement le revendeur ou l’entrepreneur qui vous a vendu l’appareil.
Gagnez du temps et de l’argent:
Avant d’appeler pour service, consultez la section de dépannage à la fi n de ce manuel.
Cette section vous aidera à résoudre les problèmes courants pouvant survenir.
1-800-26- Danby
(1-800-263-2629)
EXIGENCES DE SÉCURITÉ
Cet appareil n’est pas destiné à être utilisé par
des personnes (y compris des enfants) dont les
capacités physiques, sensorielles ou mentales
peuvent être différentes ou réduites, ou qui n’ont
pas d’expérience ou de connaissances, à moins
que ces personnes ne soient surveillées ou formées
pour faire fonctionner l’appareil par une personne
responsable de leur sécurité.
Les enfants devraient être surveillés pour s’assurer
qu’ils ne jouent pas avec l’appareil.
Pour éviter tout risque de choc électrique, ne
pas utiliser ce déshumidifi cateur dans une zone
susceptible d’accumuler de l’eau stagnante. Si cette
condition se développe, débranchez l’alimentation
avant de pénétrer dans l’eau.
Ne pas stocker ou utiliser des matériaux
combustibles tels que de l’essence ou d’autres
vapeurs ou liquides infl ammables à proximité de ce
ou d’un autre appareil.
Ne pas insérer de doigts ou d’autres objets dans
des grilles ou des ouvertures dans l’appareil.
Ne pas couvrir ou bloquer les ouvertures
d’admission et d’échappement.
N’utilisez pas l’appareil sans le fi ltre installé.
N’utilisez pas l’appareil à proximité de sources de
chaleur.
Cet appareil est destiné uniquement à des
applications résidentielles et intérieures. N’utilisez
pas ce déshumidifi cateur à l’extérieur. N’utilisez
pas ce déshumidifi cateur pour des applications
commerciales ou industrielles.
INSTRUCTIONS DE MISE À LA TERRE
Cet appareil doit être mis à la terre. La mise à
la terre réduit le risque de choc électrique en
fournissant un câble d’échappement pour le courant
électrique.
Cet appareil possède un cordon doté d’un fi l de
mise à la terre avec une fi che à 3 broches. Le
cordon d’alimentation doit être branché sur une
prise correctement mise à la terre. Si la sortie
est une prise murale à 2 broches, elle doit être
remplacée par une prise murale à 3 broches
correctement mise à la terre. La plaque signalétique
en série indique la tension et la fréquence
auxquelles l’appareil est conçu.
AVERTISSEMENT - L’utilisation incorrecte de la
che de mise à la terre peut entraîner un risque
d’électrocution. Consultez un électricien qualifi é
ou un agent de service si les instructions de mise
à la terre ne sont pas complètement comprises, ou
s’il existe un doute quant à savoir si l’appareil est
correctement mis à la terre.
Ne branchez pas l’appareil à des rallonges, des
adaptateurs ou à un autre appareil dans la même
prise murale.
Ne pas épisser le cordon d’alimentation. Ne coupez
ou retirez en aucun cas la troisième broche du
cordon d’alimentation.
Si le cordon d’alimentation est endommagé, il
doit être remplacé par le fabricant, son agent de
maintenance ou une personne qualifi ée similaire
afi n d’éviter tout risque.
Informations importantes de sécurité
LIRE ET SUIVRE TOUTES LES INSTRUCTIONS DE SÉCURITÉ
11
GARDEZ CES INSTRUCTIONS!
INSTRUCTIONS D’UTILISATION
EMPLACEMENT
Placez le déshumidifi cateur sur un plancher
lisse et plat qui est assez solide pour supporter
l’appareil avec un seau complet d’eau.
Pour maintenir l’effi cacité, faites fonctionner
l’appareil dans une zone fermée. Gardez les
portes et les fenêtres fermées à proximité.
Maintenir un dégagement minimum de 20 cm
(8 pouces) sur les côtés et l’arrière de l’appareil
et 40 cm (16 pouces) sur le dessus de l’appareil
pour permettre une circulation d’air appropriée.
La température de fonctionnement ambiante
recommandée est comprise entre 5°C (41°F) et
35°C (95°F).
Ne pas forcer les rouleaux à se déplacer sur
les moquettes car l’appareil peut basculer et
renverser de l’eau.
Chaque fois que l’appareil est placé sur son dos
ou sur son côté, il doit pouvoir se tenir debout
pendant 6 heures avant de brancher pour éviter
d’endommager les composants internes.
CARACTÉRISTIQUES
Avant
1. Sortie d’air
2. Panneau de contrôle
3. Poignées (des deux côtés)
4. Seau d’eau
Arrière
1. Entrée d’air
2. Prise de vidange continue
3. Bande de stockage du cordon d’alimentation
4. Sortie de drain de pompe
5. Cordon d’alimentation
1
2
3
4
1
2
3
4
5
12
PANNEAU DE CONTRÔLE
1. Bouton de mode continu et voyant lumineux
Appuyez sur ce bouton pour activer le
mode continu. Cela entraînera en continu
la fonction de déshumidifi cation. Le voyant
s’allume lorsque le mode continu est activé.
2. Bouton de minuterie et voyants lumineux
Utilisez ce bouton pour régler la fonction de
minuterie.
3. Voyant lumineux de dégivrage
Le témoin de dégivrage s’allume lorsque
le givre s’est accumulé à l’intérieur de
l’appareil. Cela peut indiquer que la
température ambiante est trop froide. La
fonction de déshumidifi cation cessera
jusqu’à ce que le givre ait fondu.
4. Voyant lumineux de seau plein
Le voyant du seau complet s’allume lorsque
le seau est plein d’eau. Videz le seau pour
reprendre le fonctionnement régulier.
5. Écran d’affi chage et fl èches haut et bas
• L’affi chage indique l’humidité défi nie,
l’humidité ambiante ou la fonction de
minuterie.
Les fl èches haut et bas peuvent ajuster
l’humidité défi nie ou le réglage de la
minuterie.
L’humidité peut être réglée entre 35-85%
par incréments de 5%. Pour un air plus sec,
régler l’humidité à un nombre inférieur.
Pour l’air amortisseur, régler l’humidité à un
nombre plus élevé.
• L’affi chage de l’humidité ambiante est précis
entre +/- 5%.
INSTRUCTIONS D’UTILISATION
13
6. Bouton d’alimentation
Utilisez ce bouton pour allumer ou éteindre
l’appareil.
7. Bouton de pompe et voyant lumineux
Utilisez ce bouton pour activer la pompe
de vidange. Le témoin lumineux s’allume
lorsque la pompe est active.
8. Déshumidifi cation intelligente et voyant
lumineux
Utilisez ce bouton pour activer le mode
de déshumidifi cation intelligent. Le
mode de déshumidifi cation intelligent
défi nit automatiquement l’humidité et la
vitesse du ventilateur en fonction de la
température ambiante et de l’humidité.
Le témoin lumineux s’allume lorsque le
déshumidifi cation intelligent est activé.
9. Bouton de fi ltre et voyant lumineux
La lumière du fi ltre s’allume lorsque le fi ltre
doit être nettoyé. Appuyez sur le bouton de
ltre une fois que le fi ltre a été nettoyé pour
revenir au fonctionnement régulier.
10. Bouton de ventilateur et voyant lumineux
Appuyez sur cette touche pour régler la
vitesse du ventilateur à faible ou à haute. Si
le témoin lumineux est éteint, le ventilateur
est réglé à faible vitesse. Si le témoin
lumineux est allumé, le ventilateur est réglé
sur une vitesse élevée.
11. Bouton de mode Ioniseur et voyant lumineux
Utilisez ce bouton pour activer la fonction
ioniseur. Le voyant s’allume lorsque l’ioniseur
est actif.
1
2 3 4
5
6
7 8 9
10
11
INSTRUCTIONS D’UTILISATION
14
ELIMINATION D’EAU
Il existe trois façons d’éliminer l’eau collectée de
l’appareil.
1. Seau d’eau
Le déshumidifi cateur collectera automatiquement
l’eau condensée dans le seau d’eau. Lorsque le seau
est plein, le compresseur et le ventilateur s’éteignent
et le voyant du seau complet s’allume. L’écran
affi che “P2”.
Pour vider le seau, retirez-le doucement de
l’appareil en agrippant les deux côtés et en tirant
vers l’extérieur. Soyez prudent lors de l’enlèvement
du seau, il sera plein et peut être lourd.
Ne placez pas le seau à eau directement sur le sol.
Le fond du seau est inégal et il tombera et déversera
de l’eau.
Videz le seau et remettez-le dans l’appareil. Le
déshumidifi cateur ne fonctionnera pas sans le godet
installé.
Remarque: Lorsque vous retirez le seau, le bras de
pompe pour la pompe de vidange peut tomber. Il
doit être repoussé doucement vers le haut dans la
position correcte avant de remplacer le seau.
FONCTION DE MINUTERIE
Fonction d’activation automatique
1. Appuyez sur le bouton de la minuterie jusqu’à
ce que le voyant d’activation automatique
s’allume.
2. Utilisez les fl èches haut et bas pour sélectionner
la durée souhaitée avant que l’appareil ne
s’allume. Les fl èches haut et bas ajouteront ou
soustracteront 30 minutes de temps jusqu’à
10 heures, puis à des incréments de 1 heure
jusqu’à un maximum de 24 heures.
3. L’heure sélectionnée apparaîtra sur le panneau
d’affi chage et débutera jusqu’à ce que
l’appareil s’allume.
Fonction de désactivation automatique
1. Appuyez sur le bouton de la minuterie jusqu’à
ce que le témoin de désactivation automatique
s’allume.
2. Utilisez les fl èches haut et bas pour sélectionner
la durée souhaitée avant que l’appareil ne
s’allume. Les fl èches haut et bas ajouteront ou
soustracteront 30 minutes de temps jusqu’à
10 heures, puis à des incréments de 1 heure
jusqu’à un maximum de 24 heures.
3. L’heure sélectionnée apparaîtra sur le panneau
d’affi chage et débutera jusqu’à ce que
l’appareil s’éteigne.
Utilisation automatique activée et désactivée
simultanément
Les fonctions d’activation automatique et de
désactivation automatique peuvent être utilisées
simultanément en réglant d’abord l’une puis l’autre.
Les deux voyants lumineux s’allument et l’affi chage
décompte vers le bas pour que l’appareil soit éteint
ou allumé, quelle que soit la fonction réglée en
premier.
Remarque: La minuterie ne met pas l’appareil sous
tension et hors tension indéfi niment. Les minuteries
auto activées et désactivées fonctionneront une fois,
puis l’appareil revient à un fonctionnement régulier.
Si vous éteignez l’appareil, appuyez sur le bouton
par défaut de la télécommande ou débranchez
l’appareil pour effacer tous les paramètres de la
mémoire, y compris la minuterie.
FONCTION IONISEUR
La fonction ioniseur est une forme de purifi cation
de l’air qui charge négativement l’air. Les particules
de poussière, le pollen et d’autres particules dans
l’air ne peuvent pas traverser le fi ltre lorsqu’ils sont
chargés négativement. Cela garantit que la quantité
maximale de poussière et de saleté est éliminée de
l’air. En outre, la fonction ioniseur aide à éliminer
les odeurs indésirables de l’air.
INSTRUCTIONS D’UTILISATION
15
ELIMINATION D’EAU
2. Drain continu
L’eau peut être retirée de l’appareil à l’aide du
drain continu et d’un tuyau d’arrosage standard
(non fourni).
Avant d’utiliser des fonctions de vidange
automatique, vérifi ez que tous les orifi ces de
vidange sont propres et exempts de débris. Il y a un
orifi ce de vidange dans le compartiment à godets
de l’appareil, retirez le seau pour le voir. Il y a un
port de vidange à l’arrière de l’appareil où le tuyau
de vidange se fi xe. Tous les orifi ces de vidange
doivent être nettoyés avec un cure-pipe avant
utilisation.
Remarque: Ne nettoyez pas les orifi ces de vidange
avec un élément plus rigide qu’un nettoyeur
de canalisation car cela pourrait endommager
l’appareil.
Remarque: Si les orifi ces de vidange sont obstrués
ou sales, l’eau risque de fuir du bas de l’appareil.
Retirez le couvercle de la sortie de vidange
continue et fi xez l’extrémité fi letée femelle du tuyau
d’arrosage à l’arrière de l’appareil. Dirigez l’autre
extrémité du tuyau d’arrosage vers un seau ou un
drain de plancher.
Assurez-vous que le tuyau d’arrosage n’est pas plié
et descend droit de l’arrière de l’appareil. Le drain
continu n’est activé que par gravité, de sorte que les
virages ou le mouvement vers le haut dans le tuyau
empêchent l’évacuation de l’eau.
Le tuyau d’arrosage doit être coupé afi n qu’il
ne dépasse pas 1.8 m (6 pieds) de long. Si le
tuyau de vidange est trop long, l’eau peut ne pas
s’effondrer complètement, ce qui peut entraîner une
accumulation d’eau stagnante et de la moisissure
dans le tuyau.
ELIMINATION D’EAU
3. Vidange de pompe
Si le drain continu est gênant, l’eau peut être retirée
de l’appareil à l’aide du drain de la pompe.
Lors de l’utilisation de la pompe, l’appareil remplit
d’abord le seau avec de l’eau, puis le bras de
pompe pompe l’eau du seau dans le drain et le
tuyau.
Retirez le couvercle de la sortie de vidange de la
pompe et fi xez le tuyau de vidange fourni. Dirigez
l’autre extrémité du tuyau vers un drain. Appuyez
sur le bouton de la pompe pour activer la fonction
de la pompe. Lorsque le seau est plein, la pompe
commencera à fonctionner.
Assurez-vous que le tuyau de vidange n’est
pas plié, cela peut empêcher l’eau de s’écouler
correctement et de surcharger la pompe.
Ne raccordez pas le tuyau fourni avec un autre
tuyau. La longueur maximale du tuyau de vidange
de la pompe ne doit pas dépasser 4.6 m (15
pieds). Si le tuyau de vidange est trop long, l’eau
peut ne pas s’effondrer complètement, ce qui peut
entraîner une accumulation d’eau stagnante et de la
moisissure dans le tuyau.
Lorsque vous utilisez le drain de la pompe, le godet
d’eau doit être vidé tous les jours pour s’assurer
que l’eau dans le seau ne stagne pas ou que la
moisissure augmente.
SOINS ET MAINTENANCE
FILTRE À AIR
Le fi ltre à air doit être nettoyé environ toutes les 2
semaines. Le fi ltre à air peut nécessiter un nettoyage
plus fréquent si il y a un choc important ou de la
fourrure dans l’air.
Environ toutes les deux semaines, le voyant du fi ltre
sur le panneau de commande s’allume comme un
rappel pour nettoyer le fi ltre. Suivez les étapes ci-
dessous pour nettoyer le fi ltre et retournez l’appareil
au fonctionnement normal.
1. Le ltre à air est situé derrière la grille
d’admission arrière. Pour retirer le fi ltre à air,
saisissez la languette du fi ltre au bas de la grille
et faites-la glisser vers le bas.
2. Utilisez un aspirateur avec une brosse douce
pour enlever les grands débris ou la poussière
du fi ltre à air.
3. Lavez le fi ltre dans de l’eau tiède savonneuse,
inférieure à 40°C (104°F), ou utilisez un agent
de nettoyage neutre.
4. Rincez le fi ltre avec de l’eau propre et séchez
bien avant de le réinstaller dans l’appareil.
5. Appuyez sur le bouton de fi ltrage sur le
panneau de commande pour reprendre le
fonctionnement normal.
Remarque: Ne faites pas fonctionner l’appareil sans
le fi ltre à air installé.
CODES D’ERREUR
Si le panneau d’affi chage af che l’un des codes
d’erreur ci-dessous, débranchez l’appareil, laissez
reposer pendant 5 à 10 minutes, puis rallumez-le.
Si l’erreur persiste, appelez pour le service.
AS - Erreur du capteur d’humidité
ES - Erreur du capteur de température
P2 - Seau plein
E3 - Dysfonctionnement du capteur
Eb - Seau enlevé ou non dans la position correcte
EC - Erreur du système de refroidissement ou erreur
du capteur
NETTOYAGE
Pour éviter tout risque d’électrocution, assurez-vous
que l’appareil est débranché avant d’effectuer un
nettoyage ou une maintenance.
L’extérieur de l’appareil peut être nettoyé avec un
chiffon doux ou avec un chiffon tiède et humide si
nécessaire.
N’utilisez pas d’essence, de benzène, de diluant
ou d’autres produits chimiques pour nettoyer cet
appareil car ces substances peuvent endommager
l’enduit et la déformation des pièces en plastique.
Ne versez jamais d’eau directement sur l’appareil,
car cela entraînera une détérioration des
composants électriques et de l’isolation des câbles.
Assurez-vous que les orifi ces de vidange à
l’intérieur de l’appareil et les orifi ces de vidange
à l’arrière de l’appareil sont exempts de saleté et
d’accumulation de calcium.
SOINS POUR LA FIN DE SAISON
Avant de retirer l’appareil du service pour l’année,
faites fonctionner l’appareil sur le mode ventilateur
élevé pendant une demi-journée pour vous assurer
que l’intérieur de l’appareil est sec. Cela aidera
à éviter la croissance de la moisissure ou de la
moisissure à l’intérieur de l’appareil. Assurez-vous
que le fi ltre est propre et sec. Rangez l’appareil
dans un endroit sec.
ÉLIMINATION
Cet appareil ne doit pas être considéré comme un
ordures ménagères, mais il doit être pris au point
approprié de collecte des déchets pour le recyclage
des composants électriques. Vérifi ez la conformité
réglementaire locale concernant l’élimination
approuvée et sûre de cet appareil.
16
DÉPANNAGE
PROBLÈME CAUSE POSSIBLE
L’appareil ne fonctionnera pas • La che n’est pas complètement insérée dans la prise murale
Fusible souffl é ou disjoncteur
L’humidité ambiante est inférieure à l’humidité défi nie
Seau est plein ou pas dans la bonne position
Déshumidifi cation insuf sante • Le ltre à air est sale
Flux d’air bloqué
La taille de l’appareil est trop petite pour l’application
L’humidité ambiante est inférieure à l’humidité défi nie
Bruit • Le ltre à air est sale
Seau n’est pas en bonne position
La surface du plancher n’est pas de niveau
Odeurs Formation de moisissure sur des surfaces intérieures humides
Placer un comprimé d’algaïcide dans le seau à eau
L’eau sur le sol Le raccord du tuyau est desserré
Le couvercle de drainage a été retiré
Accumulation de givre Lorsque la température ambiante est inférieure à 5°C (41°F), la
gelée peut se former
Mettez l’appareil en mode ventilateur uniquement jusqu’à ce que
le givre fond
17
Danby soins du consommateur: 1-800-263-2629
Heures d’ouverture:
Lundi à Jeudi 8 h 30 à 18 h, heure normale de l’Est
Vendredi de 8 h 30 à 16 h, heure normale de l’Est
Les informations contenues dans ce manuel sont sujettes à modifi cation sans préavis.
LIMITED IN-HOME APPLIANCE WARRANTY
This quality product is warranted to be free from manufacturer’s defects in material and workmanship, provided that the unit is used under the normal operating
conditions intended by the manufacturer.
This warranty is available only to the person to whom the unit was originally sold by Danby Products Limited (Canada) or Danby Products Inc. (U.S.A.) (hereafter
“Danby”) or by an authorized distributor of Danby, and is non-transferable.
TERMS OF WARRANTY
Plastic parts, are warranted for thirty (30) days only from purchase date, with no extensions provided.
First Year
During the rst twelve (12) months, any functional parts of this product found to be defective, will be repaired or replaced, at warrantor’s
option, at no charge to the ORIGINAL purchaser.
To obtain
Danby reserves the right to limit the boundaries of “In Home Service” to the proximity of an Authorized Service Depot. Any app liance
Service
requiring service outside the limited boundaries of “In Home Service” , it will be the consumer’s responsibility to transport the appliance (at
their own expense) to the original retailer (point of purchase) or a service depot for repair. See “Boundaries of In Home Serv ice” below.
Contact your dealer from whom your unit was purchased, or contact your nearest authorized Danby service depot, where service
must be performed by a qualied service technician.
If service is performed on the units by anyone other than an authorized service depot, or the unit is used for commercial appli cation, all
obligations of Danby under this warranty shall be void.
Boundaries of
If the appliance is installed in a location that is 100 kilometers (62 miles) or more from the nearest service center your unit must be
In Home Service
delivered to the nearest authorized Danby Service Depot, as service must only be performed by a technician qualied and certif ied for
warranty service by Danby. Transportation charges to and from the service location are not protected by this warranty and are t he
responsibility of the purchaser.
Nothing within this warranty shall imply that Danby will be responsible or liable for any spoilage or damage to food or other c ontents of this appliance, whether due
to any defect of the appliance, or its use, whether proper or improper.
EXCLUSIONS
Save as herein provided, Danby, there are no other warranties, conditions, representations or guarantees, express or implied, m ade or intended by Danby or its
authorized distributors and all other warranties, conditions, representations or guarantees, including any warranties, conditio ns, representations or guarantees
under any Sale of Goods Act or like legislation or statue is hereby expressly excluded. Save as herein provided, Danby shall no t be responsible for any damages
to persons or property, including the unit itself, howsoever caused or any consequential damages arising from the malfunction o f the unit and by the purchase of
the unit, the purchaser does hereby agree to indemnify and hold harmless Danby from any claim for damages to persons or propert y caused by the unit.
GENERAL PROVISIONS
No warranty or insurance herein contained or set out shall apply when damage or repair is caused by any of the following:
1) Power failure.
2) Damage in transit or when moving the appliance.
3) Improper power supply such as low voltage, defective house wiring or inadequate fuses.
4) Accident, alteration, abuse or misuse of the appliance such as inadequate air circulation in the room or abnormal operating con ditions
(extremely high or low room temperature).
5) Use for commercial or industrial purposes (ie. If the appliance is not installed in a domestic residence).
6) Fire, water damage, theft, war, riot, hostility, acts of God such as hurricanes, oods etc.
7) Service calls resulting in customer education.
8) Improper Installation (ie. Building-in of a free standing appliance or using an appliance outdoors that is not approved for out door application).
Proof of purchase date will be required for warranty claims; so, please retain bills of sale. In the event warranty service is required, present this document to our
AUTHORIZED SERVICE DEPOT.
Danby Products Limited
PO Box 1778, Guelph, Ontario, Canada N1H 6Z9
Telephone: (519) 837-0920 FAX: (519) 837-0449
Danby Products Inc.
PO Box 669, Findlay, Ohio, U.S.A. 45840
Telephone: (419) 425-8627 FAX: (419) 425-8629
04/09
1-800-263-2629
Warranty Service
In-home
Les frais de transport entre votre domicile et le lieu de l'entretien ne sont pas couverts par la présente garantie et doivent être
acquittés par l'acheteur.
Pendant les premiers vingt quatre (24) mois, toutes les pièces fonctionnelles de ce produit qui s’avèrent
défectueuses seront réparées ou remplacées, selon le choix du garant, sans frais à l’acheteur initial.
Contactez le revendeur où l'appareil a été acheté ou contactez le dépôt de service Danby autorisé le plus
proche, où le service doit être effectué par un technicien de service qualifié. Si le service est effectué sur
l'appareil par une personne autre qu'un dépôt de service autorisé, toutes les obligations de Danby en vertu de
cette garantie seront annulées.
Il est de la responsabilité de l'acheteur de transporter l'appareil vers le dépôt de service agréé le plus proche.
Premiers 24 mois
Pour obtenir un
service
GARANTIE LIMITÉE “EN ATELIER”
Cet appareil de qualité est garanti exempt de tout vice de matière première et de fabrication, s’il est utilisé dans les conditions normales
recommandées par le fabricant.
Cette garantie n’est offerte qu’à l’acheteur initial de l’appareil vendu par Danby Products Limited (Canada) ou Danby Products Inc.
(E.- U.A.) (ci-après « Danby ») ou par l’un des ses distributeurs agréés et elle ne peut être transférée.
CONDITIONS
Les pièces en plastique sont garanties pendant trente (30) jours seulement à partir de la date de l’achat, sans aucune prolongation
prévue.
Aucune partie de la garantie ne prévoit implicitement que le fabricant sera tenu responsable des dommages subis par les aliments ou
d’autres types de contenu, qu’ils soient causés par la défectuosité de l’appareil ou par son usage adéquat ou inadéquat.
EXCLUSIONS
En vertu de la présente, il n’existe aucune autre garantie, condition ou représentation, qu’elle soit exprimée ou tacite, de façon
manifeste ou intentionnelle, par Danby ou ses distributeurs agréés. De même, sont exclues toutes les autres garanties, conditions ou
représentations, y compris les garanties, conditions ou représentations en vertu de toute loi régissant la vente de produits ou de toute
autre législation ou règlement semblables. En vertu de la présente, Danby ne peut être tenue responsable en cas de blessures
corporelles ou des dégâts matériels, y compris à l’appareil, quelle qu’en soit les causes. Danby ne peut pas être tenue responsable
des dommages indirects dus au fonctionnement défectueux de l’appareil. En achetant l’appareil, l’acheteur accepte de mettre à
couvert et de dégager Danby de toute responsabilité en cas de réclamation pour toute blessure corporelle ou tout dégât matériel
causé par cet appareil.
CONDITIONS GÉNÉRALES
La garantie ou assurance ci-dessus ne s’applique pas si les dégâts ou réparations sont dus aux cas suivants:
1) Panne de courant.
2) Dommage subis pendant le transport ou le déplacement de l’appareil.
3) Alimentation électrique incorrecte (tension faible, câblage défectueux, fusibles incorrects).
4) Accident, modification, emploi abusif ou incorrect de l’appareil tel qu'une circulation d'air inadéquate dans la pièce ou des
conditions de fonctionnement anormales (température extrêmement élevée ou basse).
5) Utilisation dans un but commercial ou industriel (à savoir, si l'appareil n'est pas installé dans un domicile résidentiel).
6) Incendie, dommages causés par l’eau, vol, guerre, émeute, hostilités, cas de force majeure (ouragan, inondation, etc.).
7) Visites d’un technicien pour expliquer le fonctionnement de l’appareil au propriétaire.
8) Installation inappropriée (par exemple, encastrement d'un appareil autoportant, ou utilisation extérieure d'un appareil non conçu à
cet effet, y compris, mais sans s'y limiter: les garages, les patios, les porches ou ailleurs qui ne sont pas correctement isolés ou
climatisés).
La preuve de la date d'achat sera requise pour les réclamations de garantie; Conserver les factures de vente. Dans le cas où un
service de garantie est requis, présentez la preuve d'achat à notre dépôt de service agréé.
Service sous garantie
En Atelier
Danby Products Limited
PO Box 1778, Guelph, Ontario, Canada N1H 6Z9
Téléphone : (519) 837-0920 Télécopieur: (519) 837-0449
Danby Products Inc.
PO Box 669, Findlay, Ohio, U.S.A. 45840
Téléphone: (419) 425-8627 Télécopieur: (419) 425-8629
1-800-263-2629
04/17
1-800-26- Danby
(1-800-263-2629)
Bienvenido
Bienvenido a la familia Danby. Estamos orgullosos de nuestros productos de calidad y creemos en
un servicio confi able. Sugerimos que lea este manual del propietario antes de conectar el nuevo
aparato ya que contiene información importante sobre la operación, información de seguridad,
solución de problemas y consejos de mantenimiento para garantizar la fi abilidad y longevidad de
su electrodoméstico.
Visite www.Danby.com para acceder a herramientas de autoservicio, preguntas frecuentes y
mucho más. Para asistencia adicional, llame al 1-800-263-2629.
Tenga en cuenta la información siguiente; Necesitará esta información para obtener un servicio
bajo garantía.
Debe proporcionar el recibo de compra original para validar su garantía y recibir servicio.
Número de modelo: _____________________________________________
Número de serie: _______________________________________________
Fecha de compra: _______________________________________________
Necesitas ayuda?
Antes de llamar al servicio, aquí hay algunas cosas que puede hacer para ayudarnos a
servirle mejor.
Lea este manual del propietario:
Contiene instrucciones para ayudarle a usar y mantener su aparato correctamente.
Si recibe un aparato dañado:
Inmediatamente póngase en contacto con el minorista o el constructor que le vendió el
aparato.
Ahorre tiempo y dinero:
Consulte la sección de solución de problemas al fi nal de este manual antes de llamar. Esta
sección le ayudará a resolver problemas comunes que pueden ocurrir.
19
1 / 1

Danby DDR095BDPWDB Le manuel du propriétaire

Catégorie
Déshumidificateurs
Taper
Le manuel du propriétaire