Rockford Fosgate RAV DVD2 Mode d'emploi

Installation &

Operation

Installation et fonctionnement

Instalación y funcionamiento

RAV Series

DVD Source Unit

RAV DVD2

INTRODUCTION

2

Dear Customer,

Congratulations on your purchase of the world’s finest brand of car audio source units.At Rockford Fosgate we are

fanatics about musical reproduction at its best,and we are pleased you chose our product.Through years of engi-

neering expertise,hand craftsmanship and critical testing procedures, we have created a wide range of products

that reproduce music with all the clarity and richness you deserve.

For maximum performance we recommend you have your new Rockford Fosgate product installed by an

Authorized Rockford Fosgate Dealer, as we provide specialized training through Rockford Technical Training Institute

(RTTI).Please read your warranty and retain your receipt and original carton for possible future use.

Great product and competent installations are only a piece of the puzzle when it comes to your system.Make sure

that your installer is using 100% authentic installation accessories from Connecting Punch in your installation.

Connecting Punch has everything from RCA cables and speaker wire to power line and battery connectors.Insist on

it! After all, your new system deserves nothing but the best.

To add the finishing touch to your new Rockford Fosgate image order your Rockford accessories,which include

everything from T-shirts and jackets to hats and sunglasses.

To get a free brochure on Rockford Fosgate products and Rockford accessories,

visit our web site at: www.rockfordfosgate.com

or,in the U.S. call 1-800-669-9899 or FAX 1-800-398-3985.

For all other countries,call +001-480-967-3565 or FAX +001-480-967-8132.

PRACTICE SAFE SOUND™

Continuous exposure to sound pressure levels over 100dB may cause permanent

hearing loss.High powered auto sound systems may produce sound pressure levels well

over 130dB.Use common sense and practice safe sound.

GETTING STARTED

Welcome to Rockford Fosgate! This manual is designed to provide information for the owner,

salesperson and installer.For those of you who want quick information on how to install this product,

please turn to the Installation Section of this manual.Other information can be located by using the

Table of Contents.We,at Rockford Fosgate,have worked very hard to make sure all the information in

this manual is current. But, as we are constantly finding new ways to improve our product, this

information is subject to change without notice.

NOTE: This manual uses abbreviations for the following terms:

TUNER = AM/FM Radio Tuner

CDP = In-Dash CD Player

DVD = Digital Video Disc Player

AUX = External Auxiliary Input

MP3 = Computer Generated Audio File Format

If,after reading your manual,you still have questions regarding this product,we recommend that you see

your Rockford Fosgate dealer.If you need further assistance, you can call us direct at 1-800-669-9899.Be

sure to have your serial number,model number and date of purchase available when you call.

The serial number can be found on the outside of the box.Please record it in the space provided below as

your permanent record.This will serve as verification of your factory warranty and may become useful in

recovering your source unit if it is ever stolen.

Serial Number: ______________________________________

Model Number: _____________________________________

TABLE OF CONTENTS

SAFETY INSTRUCTIONS

3

Introduction. . . . . . . . . . . . . . . . . . . . . . . . . 3

Safety Instructions . . . . . . . . . . . . . . . . . . . 3

Precaution . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Contents of Carton. . . . . . . . . . . . . . . . . . . 5

Installation . . . . . . . . . . . . . . . . . . . . . . . 5-11

Installation Considerations . . . . . . . . . . . . . . 5

Mounting Locations. . . . . . . . . . . . . . . . . . . . 6

Remote . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Standard Mount. . . . . . . . . . . . . . . . . . . . . . . 7

ISO-DIN Mount. . . . . . . . . . . . . . . . . . . . . . . 7

Wiring the System. . . . . . . . . . . . . . . . . . . . . 8

Wiring Diagram. . . . . . . . . . . . . . . . . . . . . . 10

Setting Speaker Connection . . . . . . . . . . . . 11

Source Unit Features. . . . . . . . . . . . . . 12-13

Operation-Basic . . . . . . . . . . . . . . . . . . 14-18

Initial Set-Up . . . . . . . . . . . . . . . . . . . . . . . . 14

Reset Button . . . . . . . . . . . . . . . . . . . . . . . . 14

Visit our web site for the latest information on all Rockford products.

www.rockfordfosgate.com

NOTE:Review each section for more detailed information.

Power ON/OFF. . . . . . . . . . . . . . . . . . . . . . 14

Video Screen. . . . . . . . . . . . . . . . . . . . . . . . 14

Volume. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Mode Selection . . . . . . . . . . . . . . . . . . . . . . 16

Set-Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Operation-Radio Tuner . . . . . . . . . . . . 18-19

Operation-TV Tuner . . . . . . . . . . . . . . . . . 19

Operation-CD Player. . . . . . . . . . . . . . 20-21

Operation-MP3. . . . . . . . . . . . . . . . . . . 22-23

Operation-DVD . . . . . . . . . . . . . . . . . . 24-27

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Basic Operation. . . . . . . . . . . . . . . . . . . . . . 26

Advance Operation. . . . . . . . . . . . . . . . . . . 26

Setup Menu . . . . . . . . . . . . . . . . . . . . . . . . . 27

Troubleshooting . . . . . . . . . . . . . . . . . . 28-29

Specifications. . . . . . . . . . . . . . . . . . . . . . . 30

Warranty Information . . . . . . . . . . . . . . . 31

This symbol with "WARNING" is intended to alert the user to the

presence of important instructions.Failure to heed the instructions

will result in severe injury or death.

This symbol with "

CAUTION" is intended to alert the user to the

presence of important instructions.Failure to heed the instructions

can result in injury or unit damage.

CAUTION:To prevent injury and damage to the unit, please read and follow the

instructions in this manual.We want you to enjoy this system, not get a

headache.

CAUTION If you feel unsure about installing this system yourself,have it installed by a

qualified Rockford Fosgate technician.

CAUTION Before installation,disconnect the battery negative (-) terminal to prevent

damage to the unit,fire and/or possible injury.

CAUTION:To prevent accidents, never use the video screen to view DVDs or make

menu selections while driving the vehicle.

4

PRECAUTIONS

SOURCE UNIT

Operating Temperature

Be sure the temperature inside the vehicle is between –10° C and +65° C (+14°F and +149°F).

DO NOT play a disc if the temperature is higher or lower than the operating range.

Moisture Condensation

The CD or DVD playback may waver due to condensation.If this occurs, remove the disc from

the source unit and wait approximately an hour for the moisture to evaporate.

Environment Exposure

DO NOT expose the Source Unit to any of the following:direct sun and heat,high humidity,

excessive dust,excessive vibration and rain or water.

Handling the Detachable Faceplate

DO NOT drop or cause shock to the faceplate as serious damage may occur. Protect the

faceplate by storing it in the supplied carrying case.

Avoid Mechanical Malfunction

DO NOT grab a disc while it is being automatically loaded into the source unit. Doing this may

cause serious damage to the playback mechanism and/or damage to the disc.

IR REMOTE CONTROLLER

Environment Exposure

DO NOT expose the IR Remote to any of the following:direct sun and heat,high humidity and

rain or water.

Handling the IR Remote

DO NOT drop or cause shock to the IR Remote as serious damage may occur.

COMPACT DISCS–CDs and DVDs

Disc Handling and Care

DO NOT touch the playing side (opposite of label side) of the disc.When handling the disc,only

the outer edges or center hole of the disc should be touched.DO NOT affix any sticker or label

to the disc. DO NOT apply vinyl record spray,anti-static agent, acetone,or any other volatile

chemicals to the disc.

Damaged Disc

DO NOT play a cracked,warped,or damaged disc.Doing this may cause serious damage to the

playback mechanism.

New Discs

The CD/DVD player will eject discs that have either been inserted incorrectly or have irregular

surfaces.If a new disc is ejected after loading,feel around the outer edge of the disc and its center

hole.Any small burrs or irregularities could inhibit proper loading of the disc.To remove the burrs,

rub the inside edge of the hole and outside edge of the disc with an object such as a ball point

pen.

5

INSTALLATION

INSTALLATION CONSIDERATIONS

The following is a list of tools needed for installation:

Volt/Ohm Meter

Wire strippers

Wire crimpers

Wire cutters

#2 Phillips screwdriver

Battery post wrench

Hand held drill w/assorted bits

1/8" diameter heatshrink tubing

Assorted connectors

Soldering iron

Solder

Heat gun

This section focuses on some of the vehicle considerations for installing your new Source Unit. Pre-

planning your system layout and best wiring routes will save installation time.When deciding on the layout

of your new system,be sure that each component will be easily accessible for making adjustments.

CAUTION:If you feel unsure about installing this system yourself,have it installed by a

qualified technician.

CAUTION:Before installation,disconnect the battery negative (-) terminal to prevent

damage to the unit,fire and/or possible injury.

Before beginning any installation,follow these simple rules:

1. Be sure to carefully read and understand the instructions before attempting to install the Unit.

2. For safety, disconnect the negative lead from the battery prior to beginning the installation.

3. For easier assembly, we suggest you run all wires prior to mounting your Source Unit in place.

4. Route all of the RCA cables close together and away from any high current wires.

5. Use high quality connectors for a reliable installation and to minimize signal or power loss.

6. Think before you drill! Be careful not to cut or drill into gas tanks,fuel lines, brake or hydraulic lines,

vacuum lines or electrical wiring when working on any vehicle.

7. Never run wires underneath the vehicle. Running the wires inside the vehicle provides the best

protection.

8. Avoid running wires over or through sharp edges.Use rubber or plastic grommets to protect any

wires routed through metal,especially the firewall.

9. ALWAYS protect the battery and electrical system from damage with proper fusing.Install the

appropriate fuse holder and fuse on the +12V power wire within 18” (45.7 cm) of the battery

terminal.

10. When grounding to the chassis of the vehicle, scrape all paint from the metal to ensure a good,clean

ground connection. Grounding connections should be as short as possible and always be connected to

metal that is welded to the main body,or chassis, of the vehicle.

CONTENTS OF CARTON

A model RAV DVD2 Source unit

Installation & Operation Manual

Standard Mounting Sleeve

Back strap (taped to box insert)

Chassis Release Keys (2)

Hardware Package

8-pin Power Harness (Source Unit)

16-pin Power Harness (Tuner Unit)

13-pin DIN Communication Cable

Optical Cable

TV Antenna Assembly (2)

Faceplate Cases (1 Soft and 1 Hard)

IR Remote Control

6

INSTALLATION

MOUNTING LOCATIONS

Engine Compartment

Never mount the source or tuner unit in the engine compartment.Mounting the source or tuner unit in

the engine compartment will void your warranty.

SOURCE UNIT

The mounting position of your source unit will have a great effect on the performance of your in-dash

CD/DVD Player.The source unit can be installed in a wide range of operating locations.However, care

should be taken to ensure optimum performance.

NOTE:Make sure there is adequate room for the motorized screen to move into a viewing position.

Instrument Panel

Mounting the source unit in the instrument panel provides optimum access.The source unit should be

securely mounted using the “Standard Mount” or “ISO-DIN Mount” method to ensure optimum CD/DVD

Player performance.

Center Console

Mounting the source unit in the center console provides optimum access.Be sure the installation does not

interfere with the operation of the gear shift or parking brake.

Glove Box

Mounting the source unit in the glove box is adequate, but does not provide easy access. Glove box

mounting should only be done if “Instrument Panel” or ”Center Console,” mounting is not acceptable (i.e.,

maintaining integrity of older vehicles with metal dashboards.)

Under Dash

Mounting the source unit under the dash is adequate,but does not provide easy access.Under dash

mounting should only be done if “Instrument Panel,” ”Center Console” or ”Glove Box” mounting is not

acceptable. Mount the source unit off to the side of the driver's area to reduce interference with the

parking brake,gear shift, or operating pedals.

NOTE:The source unit should have a mounting angle within ±20° from horizontal.

TUNER UNIT

Mount the tuner unit in a location that will allow easy access for the various connections.Unusually under

a seat,behind the console or in a console cavity.Allow for adequate ventilation around the tuner unit.

Never mount the tuner unit in a location where it may impair the controls of the vehicle such as the

brake,clutch, parking brake, shift lever, etc.

REMOTE

Install the clip mount for the remote using two (2) screws or double-sided tape in a location that allows

easy access.

CAUTION:To prevent accidents, never place the remote where it will impair the safe

operation of a vehicle.

Battery Installation

1. Remove the battery cover on the back of the remote.

2 Install two (2) AAA batteries with the polarities correct as shown by the diagram inside the battery

compartment of the remote.

7

INSTALLATION

STANDARD MOUNT

Installing;

• Mount the Locks for the Installation

Sleeve onto the source unit (use

supplied screws).

• Mount the Installation Sleeve into a

secure instrument panel.

NOTE:Make sure to mount the Source

Unit as close to horizontal as

possible for optimum CD/DVD

Player performance. Mounting

Angles of up to ±20˚ from

horizontal can be

accommodated.

NOTE:Make sure there is adequate

room for the motorized screen

to move into a viewing position.

• Bend Appropriate Tabs on all sides of

the installation sleeve.

• Install Source Unit by sliding unit into

installation sleeve until it clicks into

place.

• Mount Back Strap securely behind the

instrument panel to prevent source unit

vibration.

• Back strap Screw should be 6mm max (use

supplied screw).

Removal;

• Disconnect Back Strap from rear of radio (if

used).

• Remove Trim Piece from front of radio.

• Insert Release Keys into left and right sides of source unit to

disengage locks.

• Remove Source Unit from installation sleeve with release

keys.

ISO-DIN MOUNT

Installing;

• Remove Trim Piece and Installation Sleeve from source unit.

• Factory Bracket should align with two mounting holes on each side of source unit.

• ISO Screws should be 6mm max (use supplied screws).

• Install Source Unit into instrument panel.

Dash

Trim

Sleeve

Back Strap

Dash

Release Key

Factory Bracket

Screw

Trim

Dash

8

WIRING THE SYSTEM

NOTE:See diagram on page 10 to help you connect your system.

CAUTION:If you do not feel comfortable with wiring your new source unit,please see

your local Authorized Rockford Fosgate Dealer for installation.

CAUTION:Before installation,disconnect the battery negative (-) terminal to prevent

damage to the unit,fire and/or possible injury.

1. Install the 8-Pin and 16-Pin Power Harness by connecting the corresponding wires to the

electrical and audio system.Solder and heat shrink all connections for a reliable installation.For each

connection,cut a 1" piece of heat shrink tubing and slide over one of the wires.Strip each wire 3/8"

then twist together and solder.Slide the tubing over the connection and shrink the tubing with a hot

air gun until no bare wire is exposed.

SOURCE UNIT

8-Pin Power Harness

2. Connect the BLACK (Ground) wire to chassis ground.Prepare the chassis ground by scraping any

paint from the metal surface and thoroughly clean the area of all dirt and grease. Strip the end of the

wire and attach a ring connector. Fasten the wire to the chassis using a non-anodized screw and star

washer.

3. Connect the YELLOW (Back Up) wire to a source of constant +12V (for retaining memory on

user-programmed functions).The source should always have +12V,even when the ignition is off and

the car is not running.

4. Connect the RED (ACC +B) wire (Ignition) to a source of switched +12V (is on only when ignition

key is in “accessory” or “run” position).The switched signal is usually taken from the ACC (accessory)

position of the ignition.If the vehicle does not have an ACC position,connect the wire to the

switched ON position of the ignition.

5. Connect the GREEN/RED (Brake) wire to a switch that provides ground when the vehicle is in

park (automatic transmission) or the parking brake is on (manual or automatic transmission).This is

required for the video screen to be viewed.

6. Connect the PINK (Telephone Mute) wire for cell phone mute to the wire on the cell phone

harness that provides ground when the phone rings.

Optical Cable

7. Connect one end of the supplied optical cable into the SPDIF OUT port on the back of the source

unit.Required for DVD audio.

13-Pin DIN Communication Cable

8. Connect one end of the 13-pin DIN communication cable into the TUNER port on the back of the

source unit.

TUNER UNIT

16-PIN POWER HARNESS

9. Connect the BLACK (Ground) wire to chassis ground.Prepare the chassis ground by scraping any

paint from the metal surface and thoroughly clean the area of all dirt and grease. Strip the end of the

wire and attach a ring connector. Fasten the wire to the chassis using a non-anodized screw and star

washer.

INSTALLATION

9

10. Connect the YELLOW (Back Up) wire to a source of constant +12V (for retaining memory on

user-programmed functions).The source should always have +12V,even when the ignition is off and

the car is not running.

11. Connect the RED (ACC +B) wire (Ignition) to a source of switched +12V (is on only when ignition

key is in “accessory” or “run” position).The switched signal is usually taken from the ACC (accessory)

position of the ignition.If the vehicle does not have an ACC position,connect the wire to the

switched ON position of the ignition.

12. Connect the BLUE (Remote B+) wire to the “Remote Turn-On” leads of the amplifier(s).This will

turn-on the external amplifiers when the source unit is powered on.

13. Connect the BLUE/RED (Auto Ant) wire to the “Power Antenna” lead.This will raise a fully

automatic antenna when the source unit is powered on and the unit is in Tuner Mode.

14. Connect the ORANGE/BLACK (Rear Camera) wire to a switch that provides +12V when the

vehicle is in placed in reverse.This will switch the source unit to AUX IN V1 video input for when a

rear camera is connected.

15a.Connecting Speakers (Not using RCA connection)

Connect the speaker wires to the corresponding speaker leads by soldering and heat shrinking all

connections for a reliable installation.DO NOT chassis ground any speaker leads as damage to the system

may result.

RCA Connections

15b.Connecting Speakers (Using RCA connection)

Connect RCA cables from the tuner unit into the corresponding inputs of the amplifier(s).Be sure to

route the signal cables away from any high current wires to prevent coupling noise from radiated

electrical fields into the audio signal.The AUX OUT FL white and FR red RCAs connect to the

Front speaker's amplifier.The AUX OUT RL white and RR red RCAs connect to the Rear

speaker's amplifier.The SUB WOOFER RCA connects to the Subwoofer amplifier.The CENTER

RCA connects to the Center speaker's amplifier

16. Connect the AUX IN L1,R1, L2 and R2 to the external audio source(this inserts the audio before

the volume control on the source unit).The input voltage this circuit can accept is 1–3V RMS.

17. Connect the AUX IN V1 to a external rear camera if the wire in step 14 is being connected for that

use.The AUX IN V1 and V2 can be connected to an external video source.The source unit can switch

between DVD viewing and the external video connections.

18. The AUX OUT V1 and V2 RCAs can be connected to additional video screens.

Optical Cable

19. Connect one end of the supplied optical cable into the SPDIF IN port on the tuner unit. Required for

DVD audio.

13-Pin DIN Communication Cable

20. Connect one end of the 13-pin DIN communication cable into the HEAD port on the tuner unit.

Antenna Connections

21. Connect the TV Antennas by plugging the antenna cables into the TV ANT connectors.Be sure the

antennas are securely grounded to the vehicle for proper reception.

22. Connect the Radio Antenna by plugging the antenna cable into the RADIO ANT connector. Be sure

the antenna is securely grounded to the vehicle for proper radio reception.

INSTALLATION

10

INSTALLATION

11

INSTALLATION

SETTING SPEAKER CONNECTION

NOTE:Speaker options must be setup when the unit is first installed for the speaker output to function

properly.

NOTE:For accessing certain features or making various menu selections,the IR Remote must be used.

CAUTION:To prevent accidents, never use the video screen to view DVDs or make

menu selections while driving the vehicle.

1. Turn the unit on and allow the screen to come up into the viewing position.

2. Press and hold the S (Set-Up) on the remote until the menu setup screen appears.

3. Use the joystick on the remote to move the highlight across the menu selections,MODE,

GRAPHIC EQ,AUDIO and SPK EQ.

4. Move the highlight to select SPK EQ,press the ENTER button (ENT on joystick) to enter into the

speaker menu.

At this time we are only interested in setting which size and if the speaker is available.Adjustments

can be made later for personal preference.

5. Move the highlight to until the speaker size under FRONT is selected.

6. Select the speaker size for FRONT by pressing.ENTER.Select LARGE if speakers are designed to

operate "full range".Select SMALL for speakers intended to operate 100Hz and above.

7. Use the joystick to select the other speakers in turn to set them.

8. Select the speaker size for CENTER by pressing.ENTER. Select LARGE if speakers are designed to

operate "full range".Select SMALL for speakers intended to operate 100Hz and above.Select NONE

if no speaker is being used.

9. Select the speaker size for REAR by pressing.ENTER. Select LARGE if speakers are designed to

operate "full range".Select SMALL for speakers intended to operate 100Hz and above.

NOTE:Speaker size selection only effects output frequencies when using a Dolby Digital or DTS encoded

disc.

10. Select S.W.(Sub Woofer) On or Off by pressing.ENTER. Select On if Subwoofer is connected. Select

Off if it is not available.

Speakers are now configured for the system installed.

12

SOURCE UNIT FEATURES

12 3

4

5 6 7 8 9 10 11 12 13 14 15 16

Features for DVD mode are shown in the Operation-DVD section of this manual

NOTE:Some functions only operate in conjunction with the video screen and may only be accessible by

using the IR Remote.

1. OPEN (Video Screen)– Opens and closes the video screen.Press and hold to lay the video screen

flat down without fully retracting.

2. I/O (In/Out - Video Screen)– While the screen is in the full open position, use to slide the screen

slightly inward or outward.Once set, the unit will remember the position whenever the screen is

opened.

3. TILT – Up or DOWN (Video Screen)– Use to tilt the screen in 5° increments either UP (back)

or DOWN (forward). Once set,the unit will remember the position whenever the screen is opened.

4. VOLUME (PUSH PWR OFF / ENTER) – Used to control volume level.Push and hold to turn

the unit off.Press to select item in set-up mode.

5. Down – Press to seek to previous station (Radio or TV) or press and hold to manually move

down the frequencies in TUNER (Radio or TV) mode.Selects the previous track in CD mode.Press

and hold for Fast Reverse in CD mode.

6. Up – Press to seek to next station (Radio or TV) or press and hold to manually move up the

frequencies in TUNER (Radio or TV) mode. Selects the next track in CD mode. Press and hold for

Fast Forward in CD mode.

7. MODE – Selects between DISC/RADIO TUNER/TV TUNER/AUX 1/AUX 2 modes.

8. (Back) – Selects down through the presets in TUNER (Radio or TV) mode.

See MP3 or DVD Operation.

9. (Forward) – Selects up through the presets in TUNER (Radio or TV) mode.

See MP3 or DVD Operation.

10. SETUP – When pressed,enters into the GRAPHIC EQ adjust ment screen.Press and hold to enter

set-up menu;MODE (Mode selection and preferences) GRAPHIC EQ,AUDIO (fine tuning speaker

adjustments) and SPK EQ (Speaker EQ for setting basic EQ styles,Classic,Jazz, Pop,Rock,and Vocal, as

well as setting speaker size and availability).The video screen must be in the viewing position to use

these menus.

11. PUNCH – Enables both bass and treble responses to be boosted and selects the boost level.

12. DISP – Press to show the TV Tuner presets when in TV Turner mode. Press and hold to enter in to a

screen adjustment menu for BRIGHT,DIMMER,TINT and COLOR.The video screen must be in the

viewing position and a disc inserted to use this menu.

13. BSM (Best Station Memory) – In Tuner (Radio or TV) mode, press and hold to auto store the

strongest stations in each tuner bank, FM1,FM2,AM and TV Tuner presets.

14. P/SCAN (Preset Scan) – Press to scan through the presets in a tuner bank (Radio or TV). Each

preset station will stay on for 15 seconds before going to the next.Press and hold to change the

screen size shown on the display, Full, Fit or Standard.

15.

MUTE – Mutes audio in all modes.

16.

(Eject) – Press to eject disc.

IR Remote Special Features

NOTE:For accessing certain features or making various menu selections,

the IR Remote must be used.

17. PWR – Turns the source unit on and off.

18 Joystick Control (ENT) – Move highlight in menu selections.Press to

enter selection,also to enter into folders and select tracks in MP3

mode.

19 Joystick Control (Return - Toggle Left) – Use to exit or move back

through menus in set-up mode.

20. (Stop) – Stop disc play in CD Mode.

21. (Play) – Plays the disc in CD mode.Press to pause in CD mode.

22. VOL (Volume) – Used to control volume level."-" decreases the

volume level and "+" increases the volume level.

23 (Fast Forward) – Press to seek to next station or press and

hold to manually move up the frequencies in Tuner (Radio or TV)

mode. Selects the next track in CD mode. Press and hold for Fast

Forward in CD mode.

24 (Fast Reverse) – Press to seek to previous station or press and

hold to manually move down the frequencies in Tuner (Radio or TV)

mode. Selects the previous track in CD mode.Press and hold for Fast

Reverse in CD mode.

25. OPEN/EJ – Opens and closes the video screen.Press and hold to

eject disc in CD mode.

26. NUMERIC BUTTONS – In TV Tuner mode press to select a station

channel (02-69).In Radio Tuner mode press to select preset, or press

and hold to save the set radio station in preset selected,1- 6, for the

tuner bank currently in (FM1,FM2 or AM). In CD mode, press to select

track number.

27. 2/RPT – Selects radio preset #2 in Radio Tuner mode and repeats the

current track in CD mode.

28. 3/RDM – Selects radio preset #3 in Radio Tuner mode and selects

tracks at random in CD mode.

29 6/A-B RPT – Selects radio preset #6 in Radio Tuner mode,or A-B

repeat select in CD Mode.During disc play press once for beginning of

repeat duration,press again for the end of repeat duration,the track will

repeat for the selected duration.

30. SEARCH / AS – In Tuner (Radio or TV) mode, press and hold to auto

store the strongest stations in each tuner bank,FM1,FM2,AM and TV

Tuner presets. In CD mode, press and hold to enter into Time Search

mode.

For button descriptions while viewing a DVD, see

Operation-DVD

IMPORTANT: The 8-Pin communication BUS on the tuner unit is used ONLY for

the optional CD changers,RFX8810 or RFX8620M,and is not

backwards compatible with older RFX models.Rockford Fosgate

recommends connecting only the appropriate models together.

Rockford Fosgate does not assume responsibility when using other

manufacturers’ source units with Rockford Fosgate CD changers (or

vice versa).

13

SOURCE UNIT FEATURES

15

10

19

20

21

22

24

18

17

23

25

7

27

28

30

29

26

IR Remote

14

OPERATION – BASIC

INITIAL SETUP

NOTE:Items shown in () refer to remote control functions.

RESET BUTTON

CAUTION

: Do not press the Reset Button too hard

or you may cause damage that may void

your warranty. If you need assistance,

please consult an Authorized Rockford

Fosgate Dealer.

1. Insert a paper clip or other slender object into the Reset

Button hole in the lower right corner of the unit and gently

press it in until the button clicks.

POWER ON/OFF

1.Press the VOLUME (PWR) button to turn the unit on.

2.Press and hold the VOLUME button again to turn the unit off.

Just pressing the PWR button on the remote will turn the unit

off.

Any Button Wake-Up

Press any button on the unit,except the (eject) button to “wake-up”

the radio from sleep mode.Only pressing the PWR button or ENT

(joystick) on the remote will "wake up" the unit.

VIDEO SCREEN

CAUTION

:To prevent accidents,never use the video

screen to view DVDs or make menu

selections while driving the vehicle.

When the unit is first turned on,the video screen will activate and move into a viewing position.Once the

screen position has been set,other than angle, the screen will always open to that position.

NOTE:If the screen has been angled for viewing, always ensure the screen is repositioned straight to the

unit before attempting to close the screen,to turn off the unit or to turn off the vehicle.

Open

Pressing the open button will turn on the unit and position the

screen to the set viewing position.Pressing the Open button while

the screen is open will close the screen completely and the LCD

display will show the current mode information.If the screen was

closed when the unit or vehicle was turned off,the screen will

remain closed when the unit is turned back on,unless the Open

button is pressed.

While in the open position,press and hold the Open button to lay

the video screen flat down without fully retracting.This is useful

when you need to access heater controls and such that the screen

may block when open.Press the Open button to reopen the screen.

NOTE:This function only works on the Source Unit.

I/O (In / Out)

While the screen is in the open position,press the I/O button to

slide the screen slightly inward or outward. Once set,the unit will

remember the position whenever the screen is opened.

Reset

Remote

15

OPERATION – BASIC

TILT (UP / DOWN)

Pressing the UP or DOWN buttons will tilt the screen in 5°

increments either UP (back) or DOWN (forward).Once set,the

unit will remember the position whenever the screen is opened.

Angle Adjustment

NOTE:If the screen has been angled for viewing,always ensure the screen is repositioned

straight to the unit before attempting to close the screen,to turn off the unit or to

turn off the vehicle.

While the screen is in the open position,the screen can be manually angled to allow better viewing.Grasp

and pull either the lower left or right side of the screen to angle it.The screen must be repositioned

straight before you close the screen,turn off the unit or turn off the vehicle.

12°

Angled Left Straight

Pull lower corner

to angle screen

Angled Right

Screen Auto or Manual Mode

To prevent the screen from automatcally closing when the unit or

vehicle is turned off,the screen can be set to manual mode.

Press and hold both the I/O (In/Out) button on the video screen and

the {UP} button on the faceplate until "MANUAL" appears on the

LCD Display.The video screen is now set to manual mode.To reset to

automatic, press and hold the buttons again until "AUTO" appears on

the LCD Display.

VOLUME

The Volume knob on the Source Unit is a multifunction controller

and handles the Volume,power on/off and used to enter selected

menu items while in set-up screens.

To Control Volume

1. Turn the VOLUME knob clockwise, or press the "+" button on

the remote,to raise volume.

2. Turn the VOLUME knob counter-clockwise, or press the "-"

button on the remote to lower volume.

The display will shown the volume level when is is changed.The unit

will remember the set volume level.

MUTE

1. Press the MUTE button to dampen the volume.

2. Press the MUTE button a second time to revert the audio to

the previous level.

NOTE:The panel will display MUTE until the function is canceled.

Remote

16

OPERATION – BASIC

MODE SELECTION

Press the MODE button repeatedly to cycle through the following

modes:

• DISC PLAY — Only available if a disc is in the unit. Enables

CD/DVD/MP3 play if a disc is inserted.

• RADIO TUNER — Enables the Tuner,FM1/FM2/AM.

• TV TUNER — Enables the TV Tuner,68 available channels

(02 to 69).

• CDC PLAY — Only available if a CD Changer is connected.

• AUX 1 and AUX 2 — Allows for an external audio and video

source to attach to the system.

PUNCH

NOTE:There is no control on the remote to adjust the Punch level.

The Punch button enables the bass and treble response of the audio

output to be boosted for all listening levels.

1. Press the PUNCH button to enable the Punch feature and select

through four (4) levels of increased boost response.

2. Press the PUNCH button a fifth time to disable.

NOTE:The LCD display will show "Punch" and the level

when the Punch feature is being adjusted.The

video screen will have an area displaying

"PUNCH" and the current level in CD, MP3,

CDC and Radio Tuner modes.

SET-UP

Pressing the SET-UP (S) button will enter into the Graphic Equalize,

pressing and holding the SET-UP (S) button will enter into a set-up

menu that allows adjustments of various features.

NOTE:For accessing certain features or making various menu

selections,the video screen must be in the viewing position

and the IR Remote must be used.

CAUTION:To prevent accidents, never use the video

screen to view DVDs or make menu

selections while driving the vehicle.

GRAPHIC EQ

1. Press the SET-UP (S) button to enter into the Graphic EQ

feature.

2. Use the joystick on the remote to make adjustments.

3. After completing the adjustments,

use the joystick to select band and

the number of the band you want

to save your settings to (1-6),press

the joystick to save (ENT).

NOTE:If no selection is made for 15

seconds,or the Set-Up (S)

button has been pressed before

saving,the unit will revert to the

last mode you were in and no

adjustments will be saved.

Punch Level 45Hz 10-20kHz

Level 1 3dB Ø

Level 2 6dB 3dB

Level 3 9dB 6dB

Level 4 12dB 9dB

Remote

17

OPERATION – BASIC

AUDIO

This screen handles the controls for Fader and Balance,and access to the tone controls for Treble, Mid,

Bass,High-Pass and Low-Pass Filters.

1. Press and hold the SET-UP (S) button to enter into the menu screen.

2. Use the joystick on the remote to select AUDIO and press the joystick (ENT) to enter into the

Audio Adjustment screen.

3. Use the joystick to move around the selections in the Audio Adjustment screen. Press the joystick

(ENT) to enter into specific selection or to change a setting.

Speaker Lever

4. Pressing the joystick (ENT) when

Speaker Level is highlighted will allow

adjustments to speaker pairs,Front,

Rear,Left. or Right.Use the joystick

to make adjustments.Pressing up will

adjust the fronts, down-rear and so

on.Once the adjustments have been

made, press the joystick (ENT) to

return to the menu selections.

Adjustments made here will not

affect the center or woofer settings.

Front L, Front R,Rear L, Rear R, Center and Woofer

5. Pressing the joystick (ENT) when one of the Speaker Settings is highlighted will allow adjustments to

that speaker. Press up or down on the joystick to make adjustments from -9 to +9,default is 0.Once

the adjustments have been made,press the joystick (ENT) to return to the menu selections.

Infrasonic

6. Pressing the joystick (ENT) when Infrasonic is highlighted will turn the infrasonic filter either On or

Off.On turns on a high pass filter that removes inaudible low frequency information that can be

damaging to some speakers

DR Comp (Dynamic Range Compression)

7. Pressing the joystick (ENT) when DR Comp is highlighted will turn the selection either On or Off.

This feature is only usable on Dolby Digital encoded discs.

Beep

8. Pressing the joystick (ENT) when Beep is highlighted will turn the Beep indicator either On or Off.

When On,an audible "BEEP" will be heard whenever a button selection is made.

Tone

This screen is used for High-Pass frequency adjustments to the Front,Center and Rear channels and Low-

Pass frequency adjustment to the Woofer. It is also used to adjust the Treble, Mid and Bass settings

9. Press up or down on the joystick to move through the

selection.Press left or right on the joystick to change

the settings.

10. Press the joystick (ENT) when adjustments are

completed to return to the previous screen.

The default is Off or 0 on these settings.Front and Rear are

Off,80Hz, 100Hz and 150Hz.Center is Off, 80Hz,100Hz,

150Hz,200Hz and 250Hz.Woofer is Off,60Hz, 70Hz,80Hz

and 90Hz.The Treble,Mid and Bass can be adjusted from -10

to +10.

18

SPK-EQ (Speaker-EQ)

This screen handles the controls for a basic equalizer (Classic,Jazz,

Rock,Pop and Vocal), setting speaker size, connection,a sound control

for P/L audio (ProLogic) and a delay adjustment for the Center and

Surround.

NOTE:For setting speaker size and connection, see Setting Speaker

Connection on page 11.

1. Press and hold the SET-UP (S) button to enter into the menu

screen.

2. Use the joystick on the remote to select SPK-EQ and press the

joystick (ENT) to enter into the Audio Adjustment screen.

3. Use the joystick to move around the selections in the Speaker

Adjustment screen.Press the joystick (ENT) to enter into specific

selection or to change a setting.

EQ

Use this EQ to set up a basic equalizer for

the system.If the Graphic EQ has bet set

and saved,this EQ will be -overridden.

Sound

This screen is used for setting the P/L

(ProLogic) default (P/L Auto,P/L All and

P/L 2) and for setting the Center and

Surround sound delays.

1. Press up or down on the joystick to

move through the selection.Press

left or right on the joystick to

change the settings.

2. Press the joystick (ENT) when adjustments are

completed to return to the previous screen.

The default is P/L Auto for the sound and 0 for the delays.

Center can be adjusted from 0 to a 5mS (millisecond) delay.

Surround can be adjusted from 0 to a 30mS (millisecond)

delay.

Remote

OPERATION – BASIC

SELECTING A BAND

Press the MODE button repeatedly to cycle through FM1,FM2, and AM.The

act of selecting the band automatically enables that band.

OPERATION – RADIO TUNER

Remote

19

OPERATION – RADIO TUNER

OPERATION – TV TUNER

SELECTING A STATION

Press the {UP} or {Down} buttons ( or ) once

and the Tuner will seek for the next (

/

) or pervious

(

/

) station.

If you press and hold either the {UP} or {Down} button

( or ) for 1 second will put you into the Manually Tune

mode.You can now manually tune up or down at a rate of one

digit per click (pressing and holding the UP or DN {Down}

button ( or ) will allow rapid searching).

PRESET BUTTONS

Each Tuner mode—FM1,FM2, and AM—has 6 presets for a total of 18 presets.

To Set a Preset Button

1. Tune the Tuner to the station you wish to program.

2. Press and hold any preset button (1 to 0) on the remote for five seconds and it will save the station

selected in that preset number.

BSM (Best Station Memory)

If you want the Tuner to select the 6 most powerful stations in order

of their signal strength and assign them to Preset buttons 1 to 6,you

can use BSM (Best Station Memory).

1. Press and the BSM button,or press and hold the +10 (Search/AS)

button on the remote,and the Tuner will scan the entire dial.

2. BSM will store radio stations independently in the selected tuner

bank (FM1/FM2/AM).

Remote

Cover Open

SELECTING A STATION

Press the {UP} or {Down} buttons ( or ) once

and the Tuner will seek for the next (

/

) or pervious

(

/

) station.

If you press and hold either the {UP} or {Down} button

( or ) for 1 second will put you into the Manually Tune

mode.You can now manually tune up or down at a rate of one

digit per click (pressing and holding the {UP} or {Down}

button ( or ) will allow rapid searching).

Use the numeric buttons on the remote to select a station directly (02 to 69).

BSM (Best Station Memory)

To have the TV Tuner select the 12 most powerful stations in order

of their signal strength and assign them to presets,you can use BSM

(Best Station Memory).

1. Press and the BSM button,or press and hold the +10 (Search/AS)

button on the remote,and the TV Tuner will scan the entire dial.

2. BSM will store radio stations independently in the TV tuner bank.

3. Press DISP to view the presets and use or

(DISC/PRESETS) or up or down on remote joystick to move

through the presets.

Remote

Cover Open

20

OPERATION – CD PLAYER

Basic Operation

NOTE:This system will play CD-R and CD-RW discs.

SEE OPERATION – MP3 WHEN PLAYING AN MP3 DISC

To Play a CD

1. Insert a CD into the slot on the Front Panel,the disc will be

pulled into the unit and DISC LOADING will be displayed.

2. DISC PLAY will auto-select and the CD will begin playing

track 1 after loading.

3. Use {UP} or {Down} buttons ( or ) to

change tracks.

To Eject a Disc

1. Press the (Eject) or press and hold the OPEN(Eject) button

on the remote for 1 second,"EJECT" appears on the display and

the disc will eject.

Panel Display

While playing a disc the panel will display the track number and the time

played.

Advanced Operation

NOTE:Items shown in () refer to remote control functions.

Track Selection

1. Press the {UP} button ( ) to select the next track on

the disc.

2. Press the {Down} button ( ) to select the previous

track.

Considerations

CDDA MODE:The disc will start over at track 1 again after the

last track plays.

Forward/Reverse

Press the {Down} button ( ) and the player will take you to the start of the

same track as long as that track is more than fifteen (15) seconds in.If the track is less

than fifteen (15) seconds in,pressing the {Down} button ( ) will take the player to the beginning of

the previous track.Pressing {UP}

button ( ) takes you to the next track.

Fast Forward/Reverse

1. Press and hold the {UP} button ( ) to fast forward the track.

2. Press and hold the {Down} button ( ) to fast rewind the track.

NOTE:The panel will display the elapsed time as long as the {UP} or {Down} buttons

( or ) are pressed.

Remote

La page charge ...

Rockford Fosgate RAV DVD2 Mode d'emploi

Rockford Fosgate RAV DVD2 Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents