Panasonic PVGS250 Mode d'emploi

Spanish Quick Use Guide is included.

Guía para rápida consulta en español está incluida.

LSQT0862 A

For USA assistance, please call: 1-800-211-PANA(7262) or, contact us via the web at: http://www.panasonic.com/contactinfo

For Canadian assistance, please call: 1-800-561-5505 or visit us at www.panasonic.ca

Digital Video Camcorder

Operating Instructions

Model No. PV-GS250

Mini

Before connecting, operating or adjusting this product,

please read the instructions completely.

LSQT0862ENG.book 1 ページ２００４年１２月２１日　火曜日　午後５時９分

2

LSQT0862

Things You Should Know

Thank you for choosing Panasonic!

You have purchased one of the most

sophisticated and reliable products on the

market today. Used properly, we’re sure it will

bring you and your family years of enjoyment.

Please take time to fill in the information on the

right.

The serial number is on the tag located on the

underside of your Camcorder. Be sure to retain

this manual as your convenient Camcorder

information source.

Safety Precautions

WARNING: TO PREVENT FIRE OR SHOCK HAZARD,

DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE.

Your

Camcorder is designed to record and play back in Standard Play (SP) mode and Long Play

(LP) mode

It is recommended that only cassette tapes that have been tested and inspected for use in Camcorder

with the

mark be used.

AC Adaptor

≥The rating plate is on the underside of the AC Adaptor.

Ò

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK)

NO USER-SERVICEABLE PARTS INSIDE

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL

This symbol warns the user

that uninsulated voltage within

the unit may have sufficient

magnitude to cause electric

shock.

Therefore, it is dangerous to

make any kind of contact with

any inside part of this unit.

This symbol alerts the user that

important literature concerning

the operation and maintenance

of this unit has been included.

Therefore, it should be read

carefully in order to avoid any

problems.

Date of Purchase

Dealer Purchased From

Dealer Address

Dealer Phone No.

Model No.

Serial No.

LSQT0862ENG.book 2 ページ２００４年１２月２１日　火曜日　午後５時９分

3

LSQT0862

FCC Note: This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates, uses,

and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no guarantee

that interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment off and

on, the user is encouraged to try to correct the interference by one or more of the following measures:

≥Reorient or relocate the receiving antenna.

≥Increase the separation between the equipment and receiver.

≥Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

≥Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: To assure continued compliance, follow the attached installation instructions and use

only shielded interface cables with ferrite core when connecting to computer or peripheral devices.

Any changes or modifications not expressly approved by the party responsible for compliance could

void the user’s authority to operate this equipment.

CAUTION: TO PREVENT FIRE OR SHOCK HAZARD AND ANNOYING INTERFERENCE, USE THE

RECOMMENDED ACCESSORIES ONLY.

CAUTION: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED. REPLACE

ONLY WITH THE SAME OR EQUIVALENT TYPE.

≥Since this product gets hot during use, operate it in a well ventilated place; do not install this

equipment in a confined space such as a bookcase or similar unit.

AS WITH ANY SMALL OBJECT, SD CARDS CAN BE SWALLOWED BY YOUNG CHILDREN. DO

NOT ALLOW CHILDREN TO HANDLE THE SD CARD.

Declaration of Conformity

Trade Name: Panasonic

Model No.: PV-GS250

Responsible party: Panasonic Corporation of North America

One Panasonic Way, Secaucus, NJ 07094

Support Contact: Panasonic Consumer Electronics Company

1-800-211-PANA (7262)

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1)This device may not cause harmful interference, and (2) this device must accept

any interference received, including interference that may cause undesired operation.

WARNING

LSQT0862ENG.book 3 ページ２００４年１２月２１日　火曜日　午後５時９分

4

LSQT0862

IMPORTANT SAFETY INSTRUCTIONS

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus

(including amplifiers) that produce heat.

9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two

blades with one wider than the other. A grounding type plug has two blades and a third grounding

prong. The wide blade or the third prong are provided for your safety. If the provided plug does not

fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10) Protect the power cord from being walked on or pinched particularly at plugs, convenience

receptacles, and the point where they exit from the apparatus.

11) Only use attachments/accessories specified by the manufacturer.

12) Use only with the cart, stand, tripod, bracket, or the table specified by the

manufacturer, or sold with the apparatus. When a cart is used, use caution

when moving the cart/apparatus combination to avoid injury from tip-over.

13) Unplug this apparatus during lightning storms or when it will be left unused for

long periods of time.

14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has

been damaged in any way, such as when the power-supply cord or plug is damaged, liquid has

been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or

moisture, does not operate normally, or has been dropped.

S3125A

LSQT0862ENG.book 4 ページ２００４年１２月２１日　火曜日　午後５時９分

5

LSQT0862

Precautions

USE & LOCATION

≥TO AVOID SHOCK HAZARD ... Your

Camcorder and power supply should not be

exposed to rain or moisture. Do not connect the

power supply or operate your Camcorder if it

gets wet. Your Camcorder has been designed

for outdoor use, however it is not designed to

sustain direct exposure to water, rain, sleet,

snow, sand, dust, or a direct splashing from a

pool or even a cup of coffee. This action could

permanently damage the internal parts of your

Camcorder. Do not attempt to disassemble this

unit. There are no user serviceable parts inside.

Unplug your Camcorder from the power supply

before cleaning.

≥DO NOT AIM YOUR CAMCORDER AT THE

SUN OR OTHER BRIGHT OBJECTS

≥DO NOT LEAVE THE CAMCORDER WITH

THE EVF AIMED DIRECTLY AT THE SUN AS

THIS MAY CAUSE DAMAGE TO THE

INTERNAL PARTS OF THE EVF

≥DO NOT EXPOSE YOUR CAMCORDER TO

EXTENDED HIGH TEMPERATURE ... Such as,

in direct sunlight, inside a closed car, next to a

heater, etc... This action could permanently

damage the internal parts of your Camcorder.

≥AVOID SUDDEN CHANGES IN

TEMPERATURE ... If the unit is suddenly

moved from a cold place to a warm place,

moisture may form on the tape and inside the

unit.

≥DO NOT LEAVE YOUR CAMCORDER OR

THE POWER SUPPLY TURNED ON WHEN

NOT IN USE.

≥STORAGE OF YOUR CAMCORDER ... Store

and handle your Camcorder in a manner that

will not subject it to unnecessary movement

(avoid shaking and striking). Your Camcorder

contains a sensitive pick-up device which could

be damaged by improper handling or storage.

CARE

≥TO CLEAN YOUR CAMCORDER ... Do not use

strong or abrasive detergents when cleaning

your Camcorder body.

≥TO PROTECT THE LENS ... Do not touch the

surface of the lens with your hand. Use a

commercial Camcorder lens solution and lens

paper when cleaning the lens. Improper

cleaning can scratch the lens coating.

≥TO PROTECT THE FINISH OF YOUR

CAMCORDER ... Before handling your

Camcorder, make sure your hands and face are

free from any chemical products, such as

suntan lotion, as it may damage the finish.

Apparatus Claims of U.S. Patent Nos. 4,631,603, 4,577,216, and 4,819,098, licensed for limited

viewing.

This product incorporates copyright protection technology that is protected by method claims of certain

U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights

owners. Use of this copyright protection technology must be authorized by Macrovision Corporation,

and is intended for home and other limited viewing uses only unless otherwise authorized by

Macrovision Corporation. Reverse engineering or disassembly is prohibited.

WARNING

CAUTION

This class B digital apparatus complies with CANADIAN ICES-003.

A lithium ion/polymer battery that is recyclable powers the product

you have purchased. Please call 1-800-8-BATTERY for information

on how to recycle this battery.

U.S.A./CANADA CONSUMERS: ATTENTION:

LSQT0862ENG.book 5 ページ２００４年１２月２１日　火曜日　午後５時９分

6

LSQT0862

Before opening the CD-ROM package, please read the following.

End User License Agreement (for USB Driver, Video Stream

Driver and MotionDV STUDIO)

You (“Licensee”) are granted a license for the Software defined in this End User Software Agreement

(“Agreement”) on condition that you agree to the terms and conditions of this Agreement. If Licensee

does not agree to the terms and conditions of this Agreement, promptly return the Software to

Matsushita Electric Industrial Co., Ltd. (“Matsushita”), its distributors or dealers from which you made

the purchase.

Article 1 License

Licensee is granted the right to use the software, including the information recorded or described on the

CD-ROM, instruction manuals, and any other media provided to Licensee (collectively “Software”), but

all applicable rights to patents, copyrights, trademarks and trade secrets in the Software are not

transferred to Licensee.

Article 2 Use by a Third Party

Licensee may not use, copy, modify, transfer or allow any third party, whether free of charge or not, to

use, copy or modify the Software, except as expressly provided for in this Agreement.

Article 3 Restrictions on Copying the Software

Licensee may make a single copy of the Software in whole or in part solely for back-up purpose.

Article 4 Computer

Licensee may only use the Software on a single computer at a single location.

LSQT0862ENG.book 6 ページ２００４年１２月２１日　火曜日　午後５時９分

7

LSQT0862

Article 5 Reverse Engineering, Decompiling or Disassembly

Licensee may not reverse engineer, decompile, or disassemble the Software, except to the extent

either of them is permitted under law or regulation of the country where Licensee resides. Matsushita,

or its distributors or dealers will not be responsible for any defects in the Software or damage to

Licensee caused by Licensee’s reverse engineering, decompiling, or disassembly of the Software.

Article 6 Limitation of Liability

The Software is provided “AS-IS” without warranty of any kind, either expressed or implied, including,

but not limited to, warranties of non-infringement, merchantability and/or fitness for a particular

purpose. Further, Matsushita does not warrant that the operation of the Software will be uninterrupted

or error free. Matsushita or any of its distributors or dealers will not be liable for any damage suffered by

Licensee arising from or in connection with Licensee’s use of the Software.

Article 7 Export Control

Licensee agrees not to export or re-export to any country the Software in any form without the

appropriate export licenses under regulations of the country where Licensee resides, if necessary.

Article 8 Termination of License

The right granted to Licensee hereunder will be automatically terminated if Licensee violates any of the

terms and conditions of this Agreement. Upon such automatic termination, Licensee must destroy the

Software and related documentation together with all the copies thereof at Licensee’s own expense.

LSQT0862ENG.book 7 ページ２００４年１２月２１日　火曜日　午後５時９分

8

LSQT0862

Contents

Before using

Quick Guide................................................... 10

Accessories ................................................... 12

Parts identification and handling.................... 12

Fitting the lens cap......................................... 14

The one-touch free-style grip belt .................. 15

Using the LCD monitor .................................. 15

Using the viewfinder ...................................... 16

Power supply ................................................. 16

Charging time and recordable time................ 17

Inserting/removing a cassette........................ 18

Inserting/removing a card .............................. 19

Turning the Camcorder on............................. 20

Selecting a mode ........................................... 20

How to use the joystick.................................. 20

Switching the language.................................. 21

Using the menu screen.................................. 22

Setting date and time..................................... 23

Adjusting LCD monitor/viewfinder.................. 23

Using the remote control................................ 24

Magic Wire Remote Control with Narration

Mic............................................................... 26

Record mode

Check before recording ................................. 27

Recording on a tape ...................................... 28

Recording still pictures on a card while

recording image onto a tape ....................... 29

Check the recording ...................................... 29

Blank search function .................................... 29

Recording still pictures onto a card

(Photoshot) ................................................. 30

Zoom in/out function...................................... 31

Recording yourself ........................................ 32

Quick start ..................................................... 32

Backlight compensation function................... 33

MagicPix functions ........................................ 33

Soft skin mode............................................... 33

Tele-macro function....................................... 34

Fade in/fade out function ............................... 34

Wind noise reduction function ....................... 34

Using the built-in flash ................................... 35

Self-timer recording ....................................... 36

Recording images for wide-screen TVs ........ 36

Optical image stabilizer function.................... 36

RapidFire Consecutive Photoshot ................. 37

Recording in various situations

(Scene mode) ............................................. 37

Recording in natural colors

(White balance)........................................... 38

Manual focus adjustment .............................. 39

Manual shutter speed/aperture

adjustment .................................................. 40

LSQT0862ENG.book 8 ページ２００４年１２月２１日　火曜日　午後５時９分

9

LSQT0862

Playback mode

Playing back tape .......................................... 41

Slow-motion playback/

frame-by-frame playback ............................ 42

Variable-speed search function ..................... 42

Playback on TV.............................................. 43

Playing back card .......................................... 43

Deleting files recorded on a card ................... 44

Formatting a card........................................... 45

Protecting files on a card ............................... 45

Writing the printing data on a card

(DPOF setting) ............................................ 45

Edit mode

Recording from a tape onto a card ................ 46

Copying onto a DVD recorder or a VCR

(Dubbing) .................................................... 46

Recording the contents of other

equipment ................................................... 47

Using the DV cable for Recording

(Digital Dubbing) ........................................ 48

Audio dubbing................................................ 49

Printing pictures by directly connecting to

the printer (PictBridge) ................................ 51

With a PC

Using the Camcorder with a PC .................... 52

Using USB Driver........................................... 52

Connecting Computer and Camcorder .......... 53

Using as a Web camera ................................ 53

Using MotionDV STUDIO .............................. 56

To disconnect USB cable safely .................... 59

If you no longer need software or driver

(Uninstall) .................................................... 60

Notes ............................................................. 60

Menu

Menu list ........................................................ 62

Menus related to taking pictures ................... 64

Menus related to playback ............................ 64

Other menus.................................................. 65

Others

Indications ..................................................... 66

Warning/alarm indications ............................. 67

Functions cannot be used simultaneously .... 69

Before requesting repair

(Problems and solutions) ............................ 70

Cautions for Use............................................ 73

Explanation of terms...................................... 77

Specifications ................................................ 79

Camcorder Accessory System ...................... 81

Camcorder Accessory Order Form

(For USA Customers) ................................. 82

Request for Service Notice (USA Only) ........ 83

Limited Warranty (For USA Customers)........ 84

Customer Services Directory......................... 85

Warranty (For Canadian Customers) ............ 86

Index.............................................................. 87

Spanish Quick Use Guide/

Guía española para el uso rápido............... 88

LSQT0862ENG.book 9 ページ２００４年１２月２１日　火曜日　午後５時９分

Before using

10

LSQT0862

Quick Guide

ª Charging the battery

1 Connect the AC main lead to the AC adaptor

and the AC main socket.

2 Put the battery on the battery mount by

aligning the mark, and then securely plug it

in.

ª

Fitting the battery

Push the battery against the battery holder and

slide it until it clicks.

ª

Inserting/removing a cassette

1

Slide the [OPEN/EJECT] lever and open the

cassette cover.

2 After the cassette holder is opened, insert/

remove the cassette.

3 Push the [PUSH] mark 1 in order to close

the cassette holder.

4 Only after the cassette holder is completely

housed, close the cassette cover.

ª

Inserting/removing a card

1 Open the LCD monitor and then open the

card slot cover.

2 Insert/remove the card into/from the card

slot.

≥When inserting a card, face the label side 1

towards you and push it straight in with one

stroke as far as it goes.

≥When removing the card, open the card slot

cover and press the center of the card and

then pull it straight out.

3 Securely close the card slot cover.

ª

How to turn on the power

1 While pressing the button 1, set the [OFF/

ON] switch to [ON].

OPEN/

EJECT

PUSH

1

LSQT0862ENG.book 10 ページ２００４年１２月２１日　火曜日　午後５時９分

Before using

11

LSQT0862

ª How to turn off the power

1 While pressing the button 1, set the [OFF/

ON] switch to [OFF].

ª

Recording on a tape

≥Set to Tape Recording Mode.

1 Press the recording start/stop button to

start recording.

2 Press the recording start/stop button again

to pause recording.

ª

Recording still pictures onto a card

(Photoshot)

≥Set to Card Recording Mode.

1 Press the [PHOTO SHOT] button

ª

Playing back tape

≥Set to Tape Playback Mode.

1 Operate with joystick.

1/;: Playback/Pause

6: Rewind/Review playback (Reverts to

playback with the 1/; icon.)

5: Fast forward/Cue playback (Reverts to

playback with the 1/; icon.)

∫:Stop

ª

Playing back card

≥Set to Picture Playback Mode.

1 Operate with joystick.

E: Plays back the previous picture.

D: Plays back the next picture.

1/∫: Slide show (Plays back the still pictures

on the card in order) start/stop

1

PCPC

;

PC

PHOTO

SHOT

PC

LSQT0862ENG.book 11 ページ２００４年１２月２１日　火曜日　午後５時９分

Before using

12

LSQT0862

Before using

Accessories

The following are the accessories supplied with

this product.

1) AC adaptor, DC cable, AC cable

-17-

2) Battery pack -16-

3) Remote control, button-type battery -24-

4) Magic wire remote control with narration

mic

-26-

5) Lens cap -14-

6) AV cable -46-

7) Shoulder strap -14-

8) USB cable and CD-ROM -51-

Parts identification and handling

ª Camcorder

(1) Built-in flash -35-

(2)

Recording lamp -64-

(3)

Microphone (built-in, stereo) -32-, -34-

(4)

Grip belt

(One-touch free style grip belt)

-15-

(5)

Lens (LEICA DICOMAR)

≥LEICA is a registered trademark of Leica

microsystems IR GmbH and DICOMAR is a

registered trademark of Leica Camera AG.

(6) White balance sensor -39-

(7)

Remote control sensor -25-

(8)

Lock button -15-

(9)

Lock cover -15-

(10)

Audio-video input/output terminal [AV]

-46-

≥Use the supplied AV cable or headphones

only, otherwise audio may not be played

back normally.

Headphone terminal [Ë]

(11) Terminal for Magic Wire Remote Control

with Narration Mic [REMOTE]

-26-

Microphone terminal [MIC]

≥A compatible plug-in powered microphone

can be used as an external microphone.

≥When the Camcorder is connected with AC

Adaptor, sometimes noise may be heard

depending on microphone type. In that

case, please switch to battery for power

supply and noise will stop.

(12) USB terminal [ ] -51-

(13)

Speaker -41-

CAUTION:

This unit will operate on 110/120/220/240 V

AC. An AC plug adaptor may be required for

voltages other than 120 V AC. Please

contact either a local or foreign electrical

parts distributor for assistance in selecting

an alternate AC plug. We recommend using

the accessory power plug adaptor

(VJSS0070) in an area which has special AC

outlets.

1)

2)

K2KC4CB00018

6)

7)

VFC3506-1A

CR2025

3)

VYF2992

5)

N2QCBD000030

4)

VFA0425B

8)

N2QAEC000012

K2CA2CA00025

K2GJ2DZ00017PV-DAC14D

CGA-DU12

(1)

(2)

(3)

(5)

(6)

(7)

(8)

(9)

(4)

AV / Ë

REMOTE/MIC

(10)

(11)

(12)

(13)

LSQT0862ENG.book 12 ページ２００４年１２月２１日　火曜日　午後５時９分

Before using

13

LSQT0862

(14) Viewfinder -16-, -77-

(15)

Battery holder

(16) Battery eject button [PUSH BATT] -17-

(17)

Power switch [OFF/ON] -20-

(18)

Power lamp -20-

(19)

Quick start recording button

[QUICK START]

-32-

Quick start recording lamp -32-

(20)

Menu button [MENU] -22-

(21)

Joystick -20-

(22)

Mode dial -20-

(23)

Recording start/stop button -28-

(24)

S-Video input/output terminal [S-VIDEO]

-43-

(25)

Focus ring -39-

(26)

LCD monitor -15-, -77-

(27) LCD monitor open release [OPEN] -15-

(28)

Reset button [RESET] -68-

(29)

Power LCD button [POWER LCD] -24-

Power LCD lamp -24-

(30)

Mode select switch [AUTO/MANUAL/

FOCUS]

-27-, -37-, -40-

(31)

Card access lamp -19-

(32)

DV terminal [DV] -48-

(33)

Card slot cover -19-

(34)

Card slot -19-

(35)

Cassette holder -18-

(36)

Cassette eject lever [OPEN/EJECT] -18-

(37)

Cassette cover -18-

(38)

Zoom lever [W/T] -31-

Volume lever [s /VOLr] -41-

(39)

Photoshot button [PHOTO SHOT] -29-

(40)

Smart accessory shoe

The stereo zoom microphone/VW-VMH3

(optional) or the video DC light/VW-LDH3

(optional) should be mounted here.

≥When using an accessory for the smart

accessory shoe, the power is supplied from this

product.

≥When mounting or removing the accessory,

extend the viewfinder (1).

Due to limitations in LCD production

technology, there may be some tiny bright or

dark spots on the viewfinder screen.

However, this is not a malfunction and does

not affect the recorded picture.

Due to limitations in LCD production

technology, there may be some tiny bright or

dark spots on the LCD monitor screen.

However, this is not a malfunction and does

not affect the recorded picture.

S-VIDEO

(14)

(15)

(16)

(17)

(18)

(19)

(20)

(21)

(22)

(23)

(24)

(25)

(26)

(27)

(28)

(29)

(30)

(31)

(32)

(33)

(34)

(35)

(36)

(37)

(38)

(39)

1

(40)

LSQT0862ENG.book 13 ページ２００４年１２月２１日　火曜日　午後５時９分

Before using

14

LSQT0862

(41) Tripod receptacle

This is a hole for attaching the Camcorder to

optional tripod. (Please carefully read the

operating instructions for how to attach the tripod

to the Camcorder.)

≥When the tripod is used, operate the Camcorder

from the Magic Wire Remote Control with

Narration Mic for convenience. (When not using

the remote control, attach the clip to the grip belt

for convenience. When you move with remote

control attached to a pocket, etc., take care to

avoid tipping over the tripod.)

≥You cannot open the card slot cover when the

tripod is used. Insert the card first and then

attach the tripod.

(42) Shoulder strap fixture

≥Put the strap through the fixture 1 and through

the stopper 2 so it will not come off. Extend

part 3 by at least 1 inch (2 cm).

≥Fit the other end of the belt similarly.

(43) Lens hood

In order to remove the lens hood, rotate it

counter-clockwise 1. In order to fit it, put into slot

2, and then rotate it clockwise.

Fitting the lens cap

Fit the lens cap to protect the surface of the lens.

1 Remove the grip belt. Run the end of the

lens cap cord through the hole in the grip

belt attachment and run the lens cap

through the lens cap cord.

≥The lens cap removed can be attached to the

lens cap fixture. (It cannot be hung if the grip

belt is used as a hand strap.)

≥To fit or remove the lens cap, hold both sides of

the lens cap with the tips of your finger and

thumb.

(41)

(42)

3

2

1

2

(43)

LSQT0862ENG.book 14 ページ２００４年１２月２１日　火曜日　午後５時９分

Before using

15

LSQT0862

The one-touch free-style grip belt

ª To use as a hand strap

If you use the grip belt as a hand strap, then you

can carry or handle this Camcorder more easily.

1 Open the lock cover 1 by pinching the

projections 2 on both sides. Press the lock

button 3 to remove the grip belt.

≥When removing the grip belt, tightly hold the

Camcorder with both hands.

≥After removing the grip belt, restore the lock

cover to the original position.

2 Adjust the belt length.

1 Flip the belt.

2 Slide 1 in the direction indicated by the arrow.

3 Fix the belt.

3 Put your hand through the strap.

≥Use the Magic Wire Remote Control with

Narration Mic for more convenience.

≥Hold the Camcorder without covering the

microphones or the sensors with your hands.

ª

To restore the strap to the grip belt

≥When returning the grip belt to the grip belt

attachment, press the lock cover 1 and check if

the grip belt is securely locked.

ª

To use as a grip belt

Adjust the belt length so it fits your hand.

1 Adjust the belt length and the pad position.

1 Flip the belt.

2 Adjust the length.

3 Fix the belt.

Using the LCD monitor

You can record the image while viewing it on the

LCD monitor.

1 Put a finger on the LCD monitor release and

pull the LCD monitor out in the direction of

the arrow.

≥The viewfinder is now deactivated.

≥It can open up to 90o.

2 Adjust the angle of the LCD monitor

according to your preference.

≥It can rotate up to 180o 1 towards the lens or

90o 2 towards the viewfinder.

≥The brightness and color level of the LCD

monitor can be adjusted from the menu.

≥If it is forcibly opened or rotated, the Camcorder

may be damaged or fail.

≥Check that the card slot cover is closed.

≥When the LCD monitor is rotated by 180o

towards the lens (when recording yourself), the

LCD monitor and the viewfinder will be

simultaneously activated.

2

1

3

1

3

2

1

3

2

2 90o1 180o

LSQT0862ENG.book 15 ページ２００４年１２月２１日　火曜日　午後５時９分

Before using

16

LSQT0862

Using the viewfinder

ª Extending the viewfinder

1 Pull out the viewfinder and extend it by

pulling the extension knob.

ª

Lifting up the viewfinder

1 Lift it up by pinching the viewfinder

extension knob.

ª

Adjusting the field of view

1 Adjust the focus by sliding the eyepiece

corrector knob.

≥You can adjust the brightness of the viewfinder

from the menu.

Power supply

ª Charging the battery

When this product is purchased, the battery is not

charged. Charge the battery before using this

product.

≥Battery charging time (

-17-)

≥We recommend using Panasonic batteries.

≥If you use other batteries, we cannot guarantee

the quality of this product.

≥If the DC input lead is connected to the AC

adaptor, then the battery will not charge.

Remove the DC input lead from the AC adaptor.

1 Connect the AC cable to the AC adaptor and

the AC jack.

2 Put the battery on the battery mount by

aligning the mark, and then securely plug it

in.

ª

Charging lamp

Lights up: Charging

Goes off: Charging completed

Flashing: The battery is over discharged

(discharged excessively). In a while,

the lamp will light up and normal

charging will start.

When the battery temperature is

excessively high or low, the [CHARGE]

lamp flashes and the charging time will

be longer than normal.

12:30:45PM

OCT 15 2005

12:30:45PM

OCT 15 2005

12:30:45PM

OCT 15 2005

12:30:45PM

OCT 15 2005

LSQT0862ENG.book 16 ページ２００４年１２月２１日　火曜日　午後５時９分

Before using

17

LSQT0862

ª Connecting to the AC outlet

1

Connect the AC cable to the AC adaptor and

the AC jack.

2 Connect the DC cable to the AC adaptor.

3 Connect the DC cable to this product.

≥Lift up the viewfinder beforehand.

≥The output plug of the AC cable is not

completely connected to the AC adaptor jack.

As shown in 1, there is a gap.

≥Do not use the power cord for other

equipment since the power cord is exclusively

designed for this Camcorder. Do not use the

power cord from other equipment for this

Camcorder.

ª

Fitting the battery

Push the battery against the battery holder and

slide it until it clicks.

ª

Removing the battery

While pushing the [PUSH BATT] button, slide the

battery (or the DC input lead) to remove it.

≥Hold the battery with your hand so it does not

fall.

Charging time and recordable time

The times shown in the table below show the

times at a temperature of 68oF (25oC) and a

humidity of 60%. This is just a guide. If the

temperature is higher or lower than the specified

value, the charging time will become longer.

A Charging time

B Maximum continuously recordable time

“1h. 10 min.” indicates 1 hour 10 minutes.

≥The battery CGA-DU12 is supplied.

≥The times shown in the table are rough

estimates. The times indicate the recordable

time when the viewfinder is used. The times in

parentheses indicate the recordable time when

the LCD monitor is used.

≥We recommend the Battery Pack CGA-DU12

and CGA-DU21 for long recording time (2 hour

or more for continuous recording, 1 hour or

more for intermittent recording).

≥The recordable time will become shorter in the

following cases:

≥When you use both the viewfinder and the

LCD monitor simultaneously while rotating

the LCD monitor frontward to record yourself,

0 Lux MagicPix function, etc.

≥When you use this Camcorder with the LCD

monitor lit up by pressing the [POWER LCD]

button.

≥When you use accessories fitted on the

Camcorder’s smart accessory shoe such as

the stereo zoom microphone and video DC

light, etc..

≥The batteries heat up after use or charging. The

Camcorder being used will also heat up. This is

normal.

≥Along with the reduction of the battery capacity,

the display will change: r # s #

t # u # v. If the battery

discharges, then u (v) will flash.

1

PUSH

BATT

Supplied

battery/

CGA-DU12

(7.2 V/

1150 mAh)

A 2 h. 25 min.

B 2 h. 5 min.

(1 h. 55 min.)

CGA-DU21

(7.2 V/

2040 mAh)

A 3 h. 55 min.

B 3 h. 30 min.

(3 h. 15 min.)

CGR-DU06

(7.2 V/

640 mAh)

A 1 h. 40 min.

B 1 h. 5 min.

(1 h.)

LSQT0862ENG.book 17 ページ２００４年１２月２１日　火曜日　午後５時９分

Before using

18

LSQT0862

Inserting/removing a cassette

1 Slide the [OPEN/EJECT] lever and open the

cassette cover.

≥When the cover is fully opened, the cassette

holder will come out.

2 After the cassette holder is opened, insert/

remove the cassette.

≥When inserting a cassette, orient it as shown

in the figure, and then securely insert it as far

as it goes.

≥When removing, pull it straight out.

3 Push the [PUSH] mark 1 in order to close

the cassette holder.

4 Only after the cassette holder is completely

housed, close the cassette cover.

≥After using, make sure to rewind the cassette

completely, remove it, and put it in a case. Store

the case in an upright position. (

-76-)

≥When condensation is formed on the lens or the

main unit of the Camcorder, even if no

condensation alarm is indicated, condensation

may have formed on the heads or the cassette

tape. Do not open the cassette cover. (

-73-)

ª

When the cassette holder does not

come out

≥Close the cassette cover completely, and then

open it again completely.

≥Check if the battery has run down.

ª

When the cassette holder cannot be

housed

≥Set the [OFF/ON] switch to [OFF], then to [ON]

again.

≥Check if the battery has run down.

ª

Inserting/removing the cassette

≥When the cassette holder is in motion, do not

touch anything except the [PUSH] mark.

≥When inserting a previously recorded cassette,

use the blank search function to find the position

where you want to continue recording. If you

overwrite-record on a previously recorded

cassette, be sure to find the position where you

want to continue recording.

≥Close the cassette cover tightly.

≥When closing the cassette cover, do not get

anything, such as a cable, caught in the cover.

ª

Accidental erasure prevention

If the accidental erasure prevention slider 1 of a

cassette is opened (slide in the direction of the

[SAVE] arrow), the cassette cannot be recorded.

When recording, close the accidental erasure

prevention slider of the cassette (slide in the

direction of the [REC] arrow).

OPEN/

EJECT

PUSH

1

R E C

SAVE

1

LSQT0862ENG.book 18 ページ２００４年１２月２１日　火曜日　午後５時９分

Before using

19

LSQT0862

Inserting/removing a card

Before inserting/removing a card, be sure to turn

the power [OFF].

≥If the card is inserted or removed with the power

turned on, this Camcorder may malfunction or

the data recorded on the card may be lost.

1 Open the LCD monitor and then open the

card slot cover.

2 Insert/remove the card into/from the card

slot.

≥When inserting a card, face the label side 1

towards you and push it straight in with one

stroke as far as it goes.

≥When removing the card, open the card slot

cover and press the center of the card and

then pull it straight out.

3 Securely close the card slot cover.

ª

Concerning the card

≥Do not touch the terminals on the back of the

card.

≥Do not format the card with another Camcorder

or any personal computer. This operation may

make the card unusable.

≥Electrical noise, static electricity, or failure of the

Camcorder or the card may damage or erase

the data stored on the card. We recommend

saving important data on a personal computer

by using a USB cable, PC card adaptor, or USB

reader/writer.

ª

Card access lamp

≥When the Camcorder accesses the card

(reading, recording, playback, erasing, etc.), the

access lamp lights up.

≥If the following operations are performed when

the access lamp is lit, then the card or the

recorded data may be damaged or the

Camcorder may malfunction.

≥Opening the card slot cover and inserting or

removing the card

≥Operating the [OFF/ON] switch or the mode

dial

ª

SD Memory Card

≥The memory capacity indicated on the SD

Memory Card label corresponds to the total

amount of capacity to protect and manage the

copyright and the capacity available as

conventional memory for a Camcorder,

personal computer or other equipment.

ª

Concerning the write protection

switch on the SD Memory Card

≥The SD Memory Card has a write protection

switch on it. If the switch is moved to [LOCK],

you cannot write to the card, erase the data on

it, or format it. If it is moved back, you can

perform those functions.

1

LSQT0862ENG.book 19 ページ２００４年１２月２１日　火曜日　午後５時９分

Before using

20

LSQT0862

Turning the Camcorder on

When the Camcorder is turned on with the lens

cap fitted, the automatic white balance

adjustment may not function properly. Please turn

the Camcorder on after removing the lens cap.

ª

How to turn on the power

1

While pressing the button 1, set the [OFF/

ON] switch to [ON].

≥The power lamp lights up.

ª

How to turn off the power

1 While pressing the button 1, set the [OFF/

ON] switch to [OFF].

≥The power lamp goes off.

Selecting a mode

Rotate the mode dial to select the desired mode.

1 Rotate the mode dial.

≥Set your desired mode to 1.

: Tape recording mode

Use this when you want to record the image on a

tape. (Also, you can simultaneously record still

pictures on a card while recording images on a

tape.)

: Tape playback mode

Use this to play back a tape.

: Card recording mode

Use this to record still pictures on a card.

: Picture playback mode

Use this to play back the still pictures recorded on

a card.

:PC mode

You can view or edit the images recorded on a

card on your personal computer.

How to use the joystick

ª Basic joystick operations

Operations on the menu screen and selection

of files to be played back on the multi-image

display

Move the joystick up, down, left, or right to select

an item or file, and then push in the center to set

it.

ª

Joystick and screen display

Push the center of the joystick, and icons will be

displayed on the screen. Each push switches the

display as follows depending on the mode.

(In the Tape playback mode or the Picture

playback mode, the icons will be automatically

displayed on the screen.)

1) Tape recording mode

([AUTO/MANUAL/FOCUS] switch is set to

[AUTO])

1

PC

1

Joystick

PC

1 Select by moving up.

2 Select by moving down.

3 Select by moving left.

4 Select by moving right.

5 Push the center to select the item.

3 Tele-macro

-34-

4 Soft skin mode -33-

2 Fade -34-

1 Backlight compensation -33-

3 MagicPix/0 Lux MagicPix -33-

4 Recording check -29-

1

3

2

4

5

Screen

display OFF

LSQT0862ENG.book 20 ページ２００４年１２月２１日　火曜日　午後５時９分

La page charge ...

Panasonic PVGS250 Mode d'emploi

Panasonic PVGS250 Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents