RedMax Edger HE225F Manuel utilisateur

Catégorie
Coupe-herbe
Taper
Manuel utilisateur

Ce manuel convient également à

OWNER/OPERATOR MANUAL
STICK EDGERS
848-A41-93A1 (501)
HE225F
HEZ2500F
The engine exhaust from this product
contains chemicals known to the State
of California to cause cancer, birth
defects or other reproductive harm.
WARNING
Before using our product, please
read this manual carefully to
understand the proper use of your
unit.
WARNING
(HE225F) 50100000 and up
DRIVE UNIT 200001 and up ENGINE UNIT
(HEZ2500F) 50100000 and up
APPLICABLE SERIAL NUMBERS :
SAFETY FIRST
Instructions contained in warnings within this
manual marked with a symbol concern
critical points which must be taken into
consideration to prevent possible serious
bodily injury, and for this reason you are
requested to read all such instructions
carefully and follow them without fail.
WARNINGS IN THE MANUAL
This mark indicates instructions which must be
followed in order to prevent accidents which could
lead to serious bodily injury or death.
This mark indicates instructions which must be
followed, or it leads to mechanical failure,
breakdown, or damage.
This mark indicates hints or directions useful in the
use of the product.
NOTE
IMPORTANT
WARNING
CONTENTS
1. Parts location …………………………………4
2. Specifications …………………………………4
3. Warning labels on the machine ……………5
4. Symbols on the machine ……………………6
5. For safe operation ……………………………7
6. Set up …………………………………………13
7. Fuel……………………………………………14
8. Operation ……………………………………16
9. Maintenance …………………………………19
10. Storage ………………………………………23
11. Troubleshooting guide ………………………24
12. Parts list ………………………………………25
2. Specifications
HE225F/HEZ2500F
Overall size(LxWxH) ································ 68.1(1730)x12.3(313)x12.3(312) / 69.8(1773)x12.6(320)x12.3(312) in(mm)
Dry weight w/o acc. ········································································································· 13.1(5.94) / 14.1(6.39) lbs(kg)
Engine Type ····································································································· Air-cooled 2-stroke gasoline
Model ······························································································ Zenoah G24LS/Zenoah GZ25N
Displacement ········································································· 1.4cu-in (22.5cm
3
)/1.6cu-in (25.4cm
3
)
Max. output····························· 1.08Hp(0.8kW) at 8000min
-1
(rpm) / 1.2Hp(0.9kW)at 7500min
-1
(rpm)
Idle speed ······················································································ 2800min
-1
(rpm) / 3000min
-1
(rpm)
Fuel ······································································································ Mixture (Gasoline 50 : Oil 1)
Carburetor ··································································································· Walbro Diaphragm type
Spark plug······················································································ Champion RCJ6Y/NGK CMR7A
Fuel tank capacity····································································································· 20.3fl.oz (0.6 )/22.0fl.oz (0.65 )
Durability period·················································································································································· 300 hrs
Transmission········································································································ Centrifugal clutch, Flexible driveshaft
Reduction ratio························································································································································· 1.25
Cutting head rotating direction ······················································································· Clockwise(View against blade)
Blade length ········································································································································ 7.87(in)/200(mm)
Use for························································································································································ Lawn edging
Specifications are subject to change without notice.
1. Parts location
1. Loop handle
2. Ignition switch
3. Throttle cable
4. Throttle lever
5. Throttle set button
6. Blade guard
7. Blade
8. Wheel
9. Spark arrester
10. Starter knob
11. Fuel tank
12. Primer pump
13. Choke lever
14. Air cleaner cover
4
5
3. Warning labels on the machine
(1) Read owner's manual before operating this machine.
(2) Wear head, eye and ear protection.
(3) Warning/Attention
(4) Keep all children, bystanders and helpers 15 meters away from the machine.
If warning label peel off or become soiled and impossible to read, you should contact the dealer
from which you purchased the product to order new labels and affix them in the required
location(s).
Never modify your machine.
We won't warrant the machine, if you use the remodeled machine or you don't observe
the proper usage written in the manual.
WARNING
IMPORTANT
6
For safe operation and maintenance, symbols are
carved in relief on the machine. According to these
indications, please be careful not to take a mistake.
(a) The port to refuel the "MIX GASOLINE"
Position: FUEL TANK CAP
(b) The direction to close the choke
Position: AIR CLEANER COVER
(c) The direction to open the choke
Position: AIR CLEANER COVER
4. Symbols on the machine
IMPORTANT ENGINE INFORMATION
ENGINE FAMILY : 5KZXS.0254QR ; EM
ENGINE DISPLACEMENT : 25cc
REFER TO OWNER’S MANUAL FOR MAINTE-
NANCE SPECIFICATIONS AND ADJUSTMENTS.
MANUFACTURED :
THIS ENGINE CONFORMS TO
2005 U.S. EPA REGULATIONS
FOR SMALL NONROAD ENGINES.
COMPLIANCE PERIOD : CATEGORY A
CE MOTEUR EST CONFORME A LA
REGLEMENTATION U.S. EPA 2005 POUR
LES PETITS MOTEURS HORS-ROUTE.
DUREE DE CONFORMITE : CATEGORIE A
TYPE DE MOTEUR : 5KZXS.0254QR ; EM
CYLINDREE DU MOTEUR : 25 cc
SE REFERER AU MANUEL DE L’UTILISATEUR POUR LES
SPECIFICATIONS D’ENTRETIEN ET LES REGLAGES.
FABRIQUE PAR :
INFORMATION IMPORTANTE CONCERNANT LE MOTEUR
IMPORTANT ENGINE INFORMATION
ENGINE FAMILY : 5KZXS.0254CD ; EM
ENGINE DISPLACEMENT : 23cc
REFER TO OWNER’S MANUAL FOR MAINTE-
NANCE SPECIFICATIONS AND ADJUSTMENTS.
MANUFACTURED :
THIS ENGINE CONFORMS TO
2005 U.S. EPA REGULATIONS
FOR SMALL NONROAD ENGINES.
COMPLIANCE PERIOD : CATEGORY A
CE MOTEUR EST CONFORME A LA
REGLEMENTATION U.S. EPA 2005 POUR
LES PETITS MOTEURS HORS-ROUTE.
DUREE DE CONFORMITE : CATEGORIE A
TYPE DE MOTEUR : 5KZXS.0254CD ; EM
CYLINDREE DU MOTEUR : 23 cc
SE REFERER AU MANUEL DE L’UTILISATEUR POUR LES
SPECIFICATIONS D’ENTRETIEN ET LES REGLAGES.
FABRIQUE PAR :
INFORMATION IMPORTANTE CONCERNANT LE MOTEUR
[ HEZ2500F ]
[ HE225F ]
5. For safe operation
1. Read this manual carefully until you
completely understand and follow all safety
and operating instructions.
2. Keep this manual handy so that you may refer
to it later whenever any questions arise. Also
note, if you have any questions which cannot
be answered herein, contact the dealer from
whom you purchased the product.
3. Always be sure to include this manual when
selling, lending, or otherwise transferring the
ownership of this product.
4. Never allow children or anyone unable to fully
understand the directions given in the manual
to use the machine.
WORKING CONDITION
1. When using the product, you should wear proper
clothing and protective equipment.
(1) Helmet
(2) Ear protectors
(3) Protection goggles or face protector
(4) Thick work gloves
(5) Non-slip-sole work boots
2. And you should carry with you.
(1) Tools and files
(2) Properly reserved fuel
(3) Spare blade
(4) Things to notify your working area (rope,
warning signs)
(5) Whistle (for collaboration or emergency)
(6) Hatchet or saw (for removal of obstacles)
3. Do not wear loose clothing, jewelry, short
trousers, sandals, or go barefoot. Do not wear
anything which might be caught by a moving
part of the unit. Secure hair so it is above
shoulder length.
WORKING CIRCUMSTANCE
1. Never start the engine inside a closed room or
building. Exhaust gases contain dangerous
carbon monoxide.
2. Never use the product,
a. when the ground is slippery or when you can’t
maintain a steady posture.
7
8
b. At night, at times of heavy fog, or at any other
times when your field of vision might be
limited and it would be difficult to gain a clear
view of the working area.
c. During rain storms, during lightning storms, at
times of strong or gale-force winds, or at any
other times when weather conditions might
make it unsafe to use the product.
WORKING PLAN
1. You should never use the product when under
the influence of alcohol, when suffering from
exhaustion or lack of sleep, when suffering from
drowsiness as a result of having taken cold
medicine or at any other time when a possibility
exists that your judgment might be impaired or
that you might not be able to operate the product
properly and in a safe manner.
2. When planning your work schedule, allow plenty
of time to rest. Limit the amount of time over
which the product is to be used continuously to
somewhere around 30~40 minutes per session,
and take 10~20 minutes of rest between work
sessions. Also try to keep the total amount of
work performed in a single day under 2 hours or
less.
1. If you don’t observe the working time, or
working manner (See USING THE
PRODUCT), Repetitive Stress Injury(RSI)
could occur.
If you feel discomfort, redness and swelling
of your fingers or any other part of your
body, see a doctor before getting worse.
2. To avoid noise complaints, in general,
operate product between 8a.m. and 5p.m. on
weekdays and 9a.m. to 5p.m. weekends.
Check and follow the local regulations as to sound
level and hours of operations for the product.
NOTE
WARNING
5. For safe operation
BEFORE STARTING THE ENGINE
1. The area within a perimeter of 50 feet (15m) of
the person using the product should be
considered a hazardous area into which no one
should enter. If necessary yellow warning rope,
warning signs should be placed around the
perimeter of the area. When work is to be
performed simultaneously by two or more
persons, care should also be taken to constantly
look around or otherwise check for the presence
and locations of other people working so as to
maintain a distance between each person
sufficient to ensure safety.
2. Check the condition of working area to avoid any
accident by hitting hidden obstacles such as
stumps, stones, cans, or broken grass.
Remove any obstacle before beginning work.
3. Inspect the entire unit for loose fasteners and
fuel leakage. Make sure that the cutting
attachment is properly installed and securely
fastened.
STARTING THE ENGINE
1. Keep bystanders and animals at least 50feet
(15m) away from the operating point. If you are
approached, immediately stop the engine.
2. The product is equipped with a centrifugal clutch
mechanism, so the cutting attachment begins to
rotate as soon as the engine is started by putting
the throttle into the start position. When starting
the engine, place the product onto the ground in
a flat clear area and hold it firmly in place so as
to ensure that neither the cutting part nor the
throttle come into contact with any obstacle
when the engine starts.
Never place the throttle into the high speed
position when starting the engine.
3. After starting the engine, check to make sure
that the cutting attachment stops rotating when
WARNING
IMPORTANT
5. For safe operation
9
10
the throttle is moved fully back to its original
position. If it continues to rotate even after the
throttle has been moved fully back, turn off the
engine and take the unit to your authorized Red
Max servicing dealer for repair.
USING THE PRODUCT
Cut only materials recommended by the
manufacturer. And use only for tasks explained
in the manual.
1. Grip the handles firmly with both hands using
your whole hand. Place your feet slightly apart
(slightly further apart than the width of your
shoulders) so that your weight is distributed
evenly across both legs, and always be sure to
maintain a steady, even posture while working.
2. Keep cutting attachment below waist level.
3. Maintain the speed of the engine at the level
required to perform cutting work, and never raise
the speed of the engine above the level
necessary.
4. If the unit start to shake or vibrate, turn off the
engine and check the whole unit. Do not use it
until the trouble has been properly corrected.
5. Keep all parts of your body away from rotating
cutting attachment and hot surfaces.
6. Never touch the muffler, spark plug, or other
metallic parts of the engine while the engine is in
operation or immediately after shutting down the
engine. Doing so could result in serious burns or
electrical shock.
IF SOMEONE COMES
1. Guard against hazardous situations at all times.
Warn adults to keep pets and children away
from the area. Be careful if you are approached.
Injury may result from flying debris.
2. If someone calls out or otherwise interrupts you
while working, always be sure to turn off the
engine before turning around.
IMPORTANT
5. For safe operation
MAINTENANCE
1. In order to maintain your product in proper
working order, perform the maintenance and
checking operations described in the manual at
regular intervals.
2. Always be sure to turn off the engine before
performing any maintenance or checking
procedures.
The metallic parts reach high temperatures
immediately after stopping the engine.
3. When replacing any part, or when replacing the
oil or any lubricant, always be sure to use only
RedMax products or products which have
been certified by RedMax for use with the
RedMax product.
4. In the event that any part must be replaced or
any maintenance or repair work not described in
this manual must be performed, please contact a
representative from the store nearest RedMax
authorized servicing dealer for assistance.
5. Do not use any accessory or attachment other
than those bearing the RedMax mark and
recommended for the unit.
6. Under no circumstances should you ever take
apart the product or alter it in any way. Doing so
might result in the product becoming damaged
during operation or the product becoming unable
to operate properly.
WARNING
5. For safe operation
11
12
5. For safe operation
HANDLING FUEL
1. The engine of the RedMax product is designed
to run on a mixed fuel which contains highly
flammable gasoline. Never store cans of fuel or
refill the tank of the unit in any place where there
is a boiler, stove, wood fire, electrical sparks,
welding sparks, or any other source of heat or
fire which might ignite the fuel.
2. Never smoke while operating the unit or refilling
its fuel tank.
3. When refilling the tank, always turn off the
engine and allow it to cool down. Take a careful
look around to make sure that there are no
sparks or open flames anywhere nearby before
refueling.
4. Wipe spilled fuel completely using a dry rag if
any fuel spillage occurs during refueling.
5. After refueling, screw the fuel cap back tightly
onto the fuel tank and then carry the unit to a
spot 10 feet (3m) or more away from where it
was refueled before turning on the engine.
TRANSPORTATION
1. When hand-carrying the product, cover over the
cutting part, lift up the product and carry it paying
attention to the blade.
2. Never transport the product over rough roads
over long distances by vehicle without removing
all fuel from the fuel tank. If doing so, fuel might
leak from the tank during transport.
SE4
MOUNTING ENGINE (SE1)
1. Push the driveshaft housing toward the clutch
housing and rotate it by hand to check that the
driveshaft is engaged with the gears.
2. Insert the driveshaft housing into the clutch
housing until it bottoms, and align the positioning
holes on the clutch housing and the shaft tube
and install the screw. When difficult to engage,
twist the engine slightly.
3. Fasten the clamp securely with two screws.
Tighten the screws(1) gradually by turns.
Tightning Torque: 44~70in-lbs (5~8N.m.)
CONNECTING THROTTLE WIRE
1. Remove the air cleaner cover.
2. Connect the end of the throttle wire to the joint
on the top of the carburetor. (SE2)
CONNECTING SWITCH WIRES
Connect the switch wires between the engine
and the main unit. Pair the wires of the same
color.
MOUNTING OTHER PARTS
1. Insert the driveshaft into the clutch drum, then
attach the gearbox to the shaft tube as aligning
the positioning holes and fasten the screw(A).
Fasten the clamp bolt(B) firmly. (SE3)
(A)Screw
(B)Clamp bolt
(B) Tightning Torque: 52~69in-lbs(6~8N.m.)
2. Install the handle to the shaft tube and clamp at
a position best for your job. (SE4)
IMPORTANT
6. Set up
SE1
[HE225F]
[HEZ2500F]
SE2
(A)
(B)
SE3
13
14
7. Fuel
RECOMMENDED MIXING RATIO
GASOLINE 50:OIL 1
Exhaust emission are controlled by the
fundamental engine parameters and
components(eq., carburation, ignition
timing and port timing) without
addition of any major hardware or the
introduction of an inert material during
combustion.
These engines are certified to operate on
unleaded gasoline.
Make sure to use gasoline with a
minimum octane number of 89 RON
(USA/Canada: 87AL)
If you use a gasoline of a lower octane
value than prescribed, there is a danger
that the engine temperature may rise and
an engine problem such as piston seizing
may consequently occur.
Unleaded gasoline is recommended to
reduce the contamination of the air for the
sake of your health and the environment.
Poor quality gasolines or oils may damage
sealing rings, fuel lines or fuel tank of the
engine.
HOW TO MIX FUEL
Pay attention to agitation.
1. Measure out the quantities of gasoline
and oil to be mixed.
2. Put some of the gasoline into a clean,
approved fuel container.
3. Pour in all of the oil and agitate well.
4. Pour In the rest of gasoline and agitate
IMPORTANT
Gasoline is very flammable. Avoid
smoking or bringing any flame or
sparks near fuel. Make sure to stop the
engine and allow it cool before
refueling the unit. Select outdoor bare
ground for fueling and move at least
3m (10ft) away from the fueling point
before starting the engine.
The RedMax engines are lubricated by oil
specially formulated for air-cooled 2-cycle
gasoline engine use. If RedMax oil is not
available, use an anti-oxidant added
quality oil expressly labeled for air-cooled
2-cycle engine use. (JASO FC GRADE
OIL or ISO EGC GRADE)
Do not use BIA or TCW (2-stroke water-
cooling type) mixed oil.
WARNING
50:1 MIXING CHART
GASOLINE gal. 1 2345
2-CYCLE OIL fl.oz 2.6 5.2 7.8 10.4 13
GASOLINE liter 1 2345
2-CYCLE OIL ml 20 40 60 80 100
7. Fuel
15
again for at least one minute. As some
oils may be difficult to agitate depending
on oil ingredients, sufficient agitation is
necessary for the engine to last long. Be
careful that, if the agitation is insufficient,
there is an increased danger of early
piston seizing due to abnormally lean
mixture.
5. Put a clear indication on the outside of the
container to avoid mixing up with gasoline
or other containers.
6. Indicate the contents on outside of
container for easy identification.
FUELING THE UNIT
1. Untwist and remove the fuel cap. Rest the
cap on a dustless place.
2. Put fuel into the fuel tank to 80% of the full
capacity.
3. Fasten the fuel cap securely and wipe up
any fuel spillage around the unit.
1. Select bare ground for fueling.
2. Move at least 10feet (3meters) away
from the fueling point before starting
the engine.
3. Stop the engine before refueling the
unit. At that time, be sure to sufficiently
agitate the mixed gasoline in the
container.
FOR YOUR ENGINE LIFE, AVOID;
1. FUEL WITH NO OIL(RAW GASOLINE) –
It will cause severe damage to the internal
engine parts very quickly.
2. GASOHOL – It can cause deterioration of
rubber and/or plastic parts and disruption
of engine lubrication.
3. OIL FOR 4-CYCLE ENGINE USE – It can
cause spark plug fouling, exhaust port
blocking, or piston ring sticking.
4. Mixed fuels which have been left
unused for a period of one month or
more may clog the carburetor and result
in the engine failing to operate properly.
WARNING
5. In the case of storing the product for a
long period of time, clean the fuel tank
after rendering it empty. Next, activate the
engine and empty the carburetor of the
composite fuel.
6. In the case of scrapping the used mixed
oil container, scrap it only at an authorized
repository site.
As lot details of quality assurance, read the
description in the section Limited Warranty
carefully. Moreover, normal wear and
change in product with no functional
influence are not covered by the warranty.
Also, be careful that, if the usage in the
instruction manual is not observed as to the
mixed gasoline, etc. described therein, it
may not be covered by the warranty.
NOTE
16
8. Operation
OP2
(1)
(2)
(3)
OP1
(1)
(2)
(3)
OP3
(4)
(7)
(5)
(6)
OP4
The RedMax stick edgers are designed for edging
lawn in gardens, parks, roadsides and so on.
Before starting the engine, take the operating
position and adjust the handle position and the
wheel height as necessary.
ADJUSTING WHEEL HEIGHT
1. Loosen the wing nut and change the wheel
height to obtain desired cutting depth. (OP1)
(1) Deep cut
(2) Shallow cut
(3) Wing nut
2. After adjusting the height, tighten the wing nut
securely.
Tightening Torque: 51~68in-lbs (6~8N.m.)
Never adjust wheel height with the engine
running.
STARTING ENGINE
The cutting head will start rotating upon the
engine starts.
1. Rest the unit on a flat, firm place. Keep the
cutting head off the ground and clear of
surrounding objects as it will start rotating upon
starting of the engine.
2. Push the primer pump several times until
overflown fuel flows out in the clear tube. (OP2)
3. Move the choke lever to the closed position.
(OP3)
4. Set the ignition switch to the “start” position.
While pulling the throttle lever, push the set
button, and release the throttle, then the throttle
lever is in to the “start” position. (OP4)
5. While holding the unit firmly, pull out the starter
rope quickly until engine fires. (OP5)
(1) choke lever (2) close (3) open
(4) ignition switch (5) start (6) stop
(7) throttle set button
WARNING
WARNING
8. Operation
17
Avoid pulling the rope to its end or returning it by
releasing the knob. Such actions can cause
starter failures.
6. Move the choke lever downward to open the
choke. And restart engine. (OP3)
7. Allow the engine to warm up for a several
minutes before starting operation.
1. When restarting the engine immediately after
stopping it, leave the choke open.
2. Overchoking can make the engine hard to start
due to excess fuel. When the engine failed to
start after several attempts, open the choke and
repeat pulling the rope, or remove the spark plug
and dry it.
STOPPING ENGINE (OP4)
1. Release the throttle lever and run the engine for
a half minute.
2. Shift the ignition switch to the STOP position.
Except for an emergency, avoid stopping the
engine while pulling the throttle lever.
ADJUSTING THROTTLE CABLE
The normal play is 1 or 2mm when measured at
the carburetor side end. Readjust with the cable
adjuster as required. (OP6)
(1) cable adjuster
ADJUSTING IDLING SPEED (OP7)
1. When the engine tends stop frequently at idling
mode, turn the adjusting screw clockwise.
2. When the cutting head keeps rotating after
releasing the trigger, turn the adjusting screw
counter-clockwise.
(1) idle adjusting screw
Warm up the engine before adjusting the idling
speed.
NOTE
IMPORTANT
NOTE
IMPORTANT
OP5
.04 in
(1~2mm)
(1)
OP6
(1)
OP7
18
8. Operation
HOW TO USE
1 Always wear eye protection such as safety
goggles. Never lean over the rotating cutting
head. Rocks or other debris could be thrown
into eyes and face and cause serious
personal injury.
2 Keep the blade guard and the mad guard
attached in place at all times when the unit is
operated.
3 Before starting a job, check the area and
remove all obstacles and objects that could
be thrown by the blade.
4 Do not adjust the wheel height or try to
remove anything entangled to the blade with
the engine running.
1 Before starting the engine, adjust the wheel
height for desired cutting depth (See page 16).
2 Before starting a job, plan your direction of travel
so that you can always hold the edger on you
right side and can walk on a hard surface as
much as possible.
3When starting to edge, maintain the engine
speed at the level required to perform edging
work, and slowly have the blade cut into the
edge groove.
Before edging, make sure the area is soft
enough so the blade does not bog down.
Do not move the edger into the work so fast that
the engine or blade bogs down.
Do not operate using starting throttle lock. It may
cause unit uncontrolled, and clutch failure.
Use care indirecting discharge to avoid
bystanders, vehicles, glass, and the like.
When the blade guard is clogged or blade stuck,
stop the engine and clean it.
NOTE
WARNING
OP8
•Always be sure to stop the engine before inspecting the stick edger for problems or
performing maintenance.
Never alter the stick edger or take the engine apart.
•When replacing parts, always be sure to use only RedMax products or products which
have been certified by RedMax for use with the RedMax stick edger.
WARNING
9. Maintenance
19
BE SURE TO CHECK THE FOLLOWING BEFORE USING YOUR STICK EDGER
Item to be checked Response
1 Edging mechanism See if attachment is loose Tighten screws and bolts
Check if edges of blades are dull Sharpen or replace blades
2 Throttle Stiff and difficult to move Repair or replace
3 Throttle wire Too loose, too tight Adjust
Stiff and difficult to move Repair or replace
4 Engine attachment See if fittings are loose Tighten fittings
5 Fuel tank See if attachment is loose Tighten screws and bolts
See if fuel pipe is damaged Replace
See if cap packing is damaged Replace
6 Muffler See if attachment is loose Tighten screws and bolts
7 Cutting blade See if damaged or worn shorter Replace
than usable length
every every every
25 50 100
system/compornent procedure before hours hours hours note
use after after after
fuel leaks, fuel spillage wipe out
fuel tank, air filter, fuel filter inspect/clean ✔✔ replace, if necessary
see
ADJUSTING
replace carburetor
idle adjusting screw
IDLING SPEED (p.17)
if necessary
clean and readjust
GAP: .025in(0.6~0.7mm)
spark plug
plug gap replace, if necessary
cylinder fins, intake air cooling vent clean
muffler, spark arrester, cylinder exhaust port
clean
throttle lever, ignition switch check operation
replace if
cutting parts
something's wrong
gear case grease
screws/nuts/bolts tighten/replace ✔✔not adjusting screws
drive shaft grease
cutting blade inspect/replace replace, if necessary
ENGINE
SHAFT
MAINTENANCE CHART
Maintenance, replacement, or repair of the emission control device and systems may be
performed by any non-road engine repair establishment or individual.
20
•Make sure that the engine has stopped and is
cool before performing any service to the
machine. Contact with moving cutting head
or hot muffler may result in a personal injury.
AIR FILTER
The air filter, if clogged, will reduce the engine
performance. Check and clean the filter element
in warm, soapy water as required. Dry
completely before installing. If the element is
broken or shrunk, replace with a new one. (MA1)
(1) air filter
FUEL FILTER
When the engine runs short of fuel supply, check
the fuel cap and the fuel filter for blockage.
(MA2)
(1) fuel filter
SPARK PLUG
Starting failure and mis-firing are often caused
by a fouled spark plug. Clean the spark plug and
check that the plug gap is in the correct range.
For a replacement plug, use the correct type
specified by RedMax. (MA3)
REPLACEMENT PLUG:
HE225F: Champion RCJ6Y
HEZ2500F: NGK CMR7A
Note that using any spark plug other than those
designated may result in the engine failing to
operate properly or in the engine becoming
overheated and damaged.
To install the spark plug, first turn the plug until it
is finger tight, then tighten it a quarter turn more
with a socket wrench.
87~104 in-lbs
TIGHTENING TORQUE:
(9.8~11.8 N.m.)
IMPORTANT
WARNING
9. Maintenance
(1)
MA2
(1)
MA1
.025 in
0.655mm
MA3
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36

RedMax Edger HE225F Manuel utilisateur

Catégorie
Coupe-herbe
Taper
Manuel utilisateur
Ce manuel convient également à

dans d''autres langues