RedMax HE225F Manuel utilisateur

Marque: RedMax

Modèle: HE225F

Catégorie: Coupe-herbe

Taper: Manuel utilisateur

Ce manuel convient également à

OWNER/OPERATOR MANUAL

STICK EDGERS

848-A41-93A1 (501)

HE225F

HEZ2500F

The engine exhaust from this product

contains chemicals known to the State

of California to cause cancer, birth

defects or other reproductive harm.

WARNING

Before using our product, please

read this manual carefully to

understand the proper use of your

unit.

WARNING

(HE225F) 50100000 and up

DRIVE UNIT 200001 and up ENGINE UNIT

(HEZ2500F) 50100000 and up

APPLICABLE SERIAL NUMBERS :

SAFETY FIRST

Instructions contained in warnings within this

manual marked with a symbol concern

critical points which must be taken into

consideration to prevent possible serious

bodily injury, and for this reason you are

requested to read all such instructions

carefully and follow them without fail.

■ WARNINGS IN THE MANUAL

This mark indicates instructions which must be

followed in order to prevent accidents which could

lead to serious bodily injury or death.

This mark indicates instructions which must be

followed, or it leads to mechanical failure,

breakdown, or damage.

This mark indicates hints or directions useful in the

use of the product.

NOTE

IMPORTANT

WARNING

CONTENTS

1. Parts location …………………………………4

2. Specifications …………………………………4

3. Warning labels on the machine ……………5

4. Symbols on the machine ……………………6

5. For safe operation ……………………………7

6. Set up …………………………………………13

7. Fuel……………………………………………14

8. Operation ……………………………………16

9. Maintenance …………………………………19

10. Storage ………………………………………23

11. Troubleshooting guide ………………………24

12. Parts list ………………………………………25

2. Specifications

■ HE225F/HEZ2500F

Overall size(LxWxH) ································ 68.1(1730)x12.3(313)x12.3(312) / 69.8(1773)x12.6(320)x12.3(312) in(mm)

Dry weight w/o acc. ········································································································· 13.1(5.94) / 14.1(6.39) lbs(kg)

Engine Type ····································································································· Air-cooled 2-stroke gasoline

Model ······························································································ Zenoah G24LS/Zenoah GZ25N

Displacement ········································································· 1.4cu-in (22.5cm

)/1.6cu-in (25.4cm

)

Max. output····························· 1.08Hp(0.8kW) at 8000min

-1

(rpm) / 1.2Hp(0.9kW)at 7500min

-1

(rpm)

Idle speed ······················································································ 2800min

-1

(rpm) / 3000min

-1

(rpm)

Fuel ······································································································ Mixture (Gasoline 50 : Oil 1)

Carburetor ··································································································· Walbro Diaphragm type

Spark plug······················································································ Champion RCJ6Y/NGK CMR7A

Fuel tank capacity····································································································· 20.3fl.oz (0.6 )/22.0fl.oz (0.65 )

Durability period·················································································································································· 300 hrs

Transmission········································································································ Centrifugal clutch, Flexible driveshaft

Reduction ratio························································································································································· 1.25

Cutting head rotating direction ······················································································· Clockwise(View against blade)

Blade length ········································································································································ 7.87(in)/200(mm)

Use for························································································································································ Lawn edging

Specifications are subject to change without notice.

1. Parts location

1. Loop handle

2. Ignition switch

3. Throttle cable

4. Throttle lever

5. Throttle set button

6. Blade guard

7. Blade

8. Wheel

9. Spark arrester

10. Starter knob

11. Fuel tank

12. Primer pump

13. Choke lever

14. Air cleaner cover

 4 

 5 

3. Warning labels on the machine

(1) Read owner's manual before operating this machine.

(2) Wear head, eye and ear protection.

(3) Warning/Attention

(4) Keep all children, bystanders and helpers 15 meters away from the machine.

If warning label peel off or become soiled and impossible to read, you should contact the dealer

from which you purchased the product to order new labels and affix them in the required

location(s).

Never modify your machine.

We won't warrant the machine, if you use the remodeled machine or you don't observe

the proper usage written in the manual.

WARNING

IMPORTANT

 6 

For safe operation and maintenance, symbols are

carved in relief on the machine. According to these

indications, please be careful not to take a mistake.

(a) The port to refuel the "MIX GASOLINE"

Position: FUEL TANK CAP

(b) The direction to close the choke

Position: AIR CLEANER COVER

4. Symbols on the machine

IMPORTANT ENGINE INFORMATION

ENGINE FAMILY : 5KZXS.0254QR ; EM

ENGINE DISPLACEMENT : 25cc

REFER TO OWNER’S MANUAL FOR MAINTE-

NANCE SPECIFICATIONS AND ADJUSTMENTS.

MANUFACTURED :

THIS ENGINE CONFORMS TO

2005 U.S. EPA REGULATIONS

FOR SMALL NONROAD ENGINES.

COMPLIANCE PERIOD : CATEGORY A

CE MOTEUR EST CONFORME A LA

REGLEMENTATION U.S. EPA 2005 POUR

LES PETITS MOTEURS HORS-ROUTE.

DUREE DE CONFORMITE : CATEGORIE A

TYPE DE MOTEUR : 5KZXS.0254QR ; EM

CYLINDREE DU MOTEUR : 25 cc

SE REFERER AU MANUEL DE L’UTILISATEUR POUR LES

SPECIFICATIONS D’ENTRETIEN ET LES REGLAGES.

FABRIQUE PAR :

INFORMATION IMPORTANTE CONCERNANT LE MOTEUR

IMPORTANT ENGINE INFORMATION

ENGINE FAMILY : 5KZXS.0254CD ; EM

ENGINE DISPLACEMENT : 23cc

REFER TO OWNER’S MANUAL FOR MAINTE-

NANCE SPECIFICATIONS AND ADJUSTMENTS.

MANUFACTURED :

THIS ENGINE CONFORMS TO

2005 U.S. EPA REGULATIONS

FOR SMALL NONROAD ENGINES.

COMPLIANCE PERIOD : CATEGORY A

CE MOTEUR EST CONFORME A LA

REGLEMENTATION U.S. EPA 2005 POUR

LES PETITS MOTEURS HORS-ROUTE.

DUREE DE CONFORMITE : CATEGORIE A

TYPE DE MOTEUR : 5KZXS.0254CD ; EM

CYLINDREE DU MOTEUR : 23 cc

SE REFERER AU MANUEL DE L’UTILISATEUR POUR LES

SPECIFICATIONS D’ENTRETIEN ET LES REGLAGES.

FABRIQUE PAR :

INFORMATION IMPORTANTE CONCERNANT LE MOTEUR

[ HEZ2500F ]

[ HE225F ]

5. For safe operation

1. Read this manual carefully until you

completely understand and follow all safety

and operating instructions.

2. Keep this manual handy so that you may refer

to it later whenever any questions arise. Also

note, if you have any questions which cannot

be answered herein, contact the dealer from

whom you purchased the product.

3. Always be sure to include this manual when

selling, lending, or otherwise transferring the

ownership of this product.

4. Never allow children or anyone unable to fully

understand the directions given in the manual

to use the machine.

■ WORKING CONDITION

1. When using the product, you should wear proper

clothing and protective equipment.

(1) Helmet

(2) Ear protectors

(3) Protection goggles or face protector

(4) Thick work gloves

(5) Non-slip-sole work boots

2. And you should carry with you.

(1) Tools and files

(2) Properly reserved fuel

(3) Spare blade

(4) Things to notify your working area (rope,

warning signs)

(5) Whistle (for collaboration or emergency)

(6) Hatchet or saw (for removal of obstacles)

3. Do not wear loose clothing, jewelry, short

trousers, sandals, or go barefoot. Do not wear

anything which might be caught by a moving

part of the unit. Secure hair so it is above

shoulder length.

■ WORKING CIRCUMSTANCE

1. Never start the engine inside a closed room or

building. Exhaust gases contain dangerous

carbon monoxide.

2. Never use the product,

a. when the ground is slippery or when you can’t

maintain a steady posture.

 7 

 8 

b. At night, at times of heavy fog, or at any other

times when your field of vision might be

limited and it would be difficult to gain a clear

view of the working area.

c. During rain storms, during lightning storms, at

times of strong or gale-force winds, or at any

other times when weather conditions might

make it unsafe to use the product.

■ WORKING PLAN

1. You should never use the product when under

the influence of alcohol, when suffering from

exhaustion or lack of sleep, when suffering from

drowsiness as a result of having taken cold

medicine or at any other time when a possibility

exists that your judgment might be impaired or

that you might not be able to operate the product

properly and in a safe manner.

2. When planning your work schedule, allow plenty

of time to rest. Limit the amount of time over

which the product is to be used continuously to

somewhere around 30~40 minutes per session,

and take 10~20 minutes of rest between work

sessions. Also try to keep the total amount of

work performed in a single day under 2 hours or

less.

1. If you don’t observe the working time, or

working manner (See ■ USING THE

PRODUCT), Repetitive Stress Injury(RSI)

could occur.

If you feel discomfort, redness and swelling

of your fingers or any other part of your

body, see a doctor before getting worse.

2. To avoid noise complaints, in general,

operate product between 8a.m. and 5p.m. on

weekdays and 9a.m. to 5p.m. weekends.

Check and follow the local regulations as to sound

level and hours of operations for the product.

NOTE

WARNING

5. For safe operation

■ BEFORE STARTING THE ENGINE

1. The area within a perimeter of 50 feet (15m) of

the person using the product should be

considered a hazardous area into which no one

should enter. If necessary yellow warning rope,

warning signs should be placed around the

perimeter of the area. When work is to be

performed simultaneously by two or more

persons, care should also be taken to constantly

look around or otherwise check for the presence

and locations of other people working so as to

maintain a distance between each person

sufficient to ensure safety.

2. Check the condition of working area to avoid any

accident by hitting hidden obstacles such as

stumps, stones, cans, or broken grass.

Remove any obstacle before beginning work.

3. Inspect the entire unit for loose fasteners and

fuel leakage. Make sure that the cutting

attachment is properly installed and securely

fastened.

■ STARTING THE ENGINE

1. Keep bystanders and animals at least 50feet

(15m) away from the operating point. If you are

approached, immediately stop the engine.

2. The product is equipped with a centrifugal clutch

mechanism, so the cutting attachment begins to

rotate as soon as the engine is started by putting

the throttle into the start position. When starting

the engine, place the product onto the ground in

a flat clear area and hold it firmly in place so as

to ensure that neither the cutting part nor the

throttle come into contact with any obstacle

when the engine starts.

Never place the throttle into the high speed

position when starting the engine.

3. After starting the engine, check to make sure

that the cutting attachment stops rotating when

WARNING

IMPORTANT

5. For safe operation

 9 

 10 

the throttle is moved fully back to its original

position. If it continues to rotate even after the

throttle has been moved fully back, turn off the

engine and take the unit to your authorized Red

Max servicing dealer for repair.

■ USING THE PRODUCT

Cut only materials recommended by the

manufacturer. And use only for tasks explained

in the manual.

1. Grip the handles firmly with both hands using

your whole hand. Place your feet slightly apart

(slightly further apart than the width of your

shoulders) so that your weight is distributed

evenly across both legs, and always be sure to

maintain a steady, even posture while working.

2. Keep cutting attachment below waist level.

3. Maintain the speed of the engine at the level

required to perform cutting work, and never raise

the speed of the engine above the level

necessary.

4. If the unit start to shake or vibrate, turn off the

engine and check the whole unit. Do not use it

until the trouble has been properly corrected.

5. Keep all parts of your body away from rotating

cutting attachment and hot surfaces.

6. Never touch the muffler, spark plug, or other

metallic parts of the engine while the engine is in

operation or immediately after shutting down the

engine. Doing so could result in serious burns or

electrical shock.

• IF SOMEONE COMES

1. Guard against hazardous situations at all times.

Warn adults to keep pets and children away

from the area. Be careful if you are approached.

Injury may result from flying debris.

2. If someone calls out or otherwise interrupts you

while working, always be sure to turn off the

engine before turning around.

IMPORTANT

5. For safe operation

■ MAINTENANCE

1. In order to maintain your product in proper

working order, perform the maintenance and

checking operations described in the manual at

regular intervals.

2. Always be sure to turn off the engine before

performing any maintenance or checking

procedures.

The metallic parts reach high temperatures

immediately after stopping the engine.

3. When replacing any part, or when replacing the

oil or any lubricant, always be sure to use only

RedMax products or products which have

been certified by RedMax for use with the

RedMax product.

4. In the event that any part must be replaced or

any maintenance or repair work not described in

this manual must be performed, please contact a

representative from the store nearest RedMax

authorized servicing dealer for assistance.

5. Do not use any accessory or attachment other

than those bearing the RedMax mark and

recommended for the unit.

6. Under no circumstances should you ever take

apart the product or alter it in any way. Doing so

might result in the product becoming damaged

during operation or the product becoming unable

to operate properly.

WARNING

5. For safe operation

 11 

 12 

5. For safe operation

■ HANDLING FUEL

1. The engine of the RedMax product is designed

to run on a mixed fuel which contains highly

flammable gasoline. Never store cans of fuel or

refill the tank of the unit in any place where there

is a boiler, stove, wood fire, electrical sparks,

welding sparks, or any other source of heat or

fire which might ignite the fuel.

2. Never smoke while operating the unit or refilling

its fuel tank.

3. When refilling the tank, always turn off the

engine and allow it to cool down. Take a careful

look around to make sure that there are no

sparks or open flames anywhere nearby before

refueling.

4. Wipe spilled fuel completely using a dry rag if

any fuel spillage occurs during refueling.

5. After refueling, screw the fuel cap back tightly

onto the fuel tank and then carry the unit to a

spot 10 feet (3m) or more away from where it

was refueled before turning on the engine.

■ TRANSPORTATION

1. When hand-carrying the product, cover over the

cutting part, lift up the product and carry it paying

attention to the blade.

2. Never transport the product over rough roads

over long distances by vehicle without removing

all fuel from the fuel tank. If doing so, fuel might

leak from the tank during transport.

SE4

■ MOUNTING ENGINE (SE1)

1. Push the driveshaft housing toward the clutch

housing and rotate it by hand to check that the

driveshaft is engaged with the gears.

2. Insert the driveshaft housing into the clutch

housing until it bottoms, and align the positioning

holes on the clutch housing and the shaft tube

and install the screw. When difficult to engage,

twist the engine slightly.

3. Fasten the clamp securely with two screws.

Tighten the screws(1) gradually by turns.

Tightning Torque: 44~70in-lbs (5~8N.m.)

■ CONNECTING THROTTLE WIRE

1. Remove the air cleaner cover.

2. Connect the end of the throttle wire to the joint

on the top of the carburetor. (SE2)

■ CONNECTING SWITCH WIRES

• Connect the switch wires between the engine

and the main unit. Pair the wires of the same

color.

■ MOUNTING OTHER PARTS

1. Insert the driveshaft into the clutch drum, then

attach the gearbox to the shaft tube as aligning

the positioning holes and fasten the screw(A).

Fasten the clamp bolt(B) firmly. (SE3)

(A)Screw

(B)Clamp bolt

(B) Tightning Torque: 52~69in-lbs(6~8N.m.)

2. Install the handle to the shaft tube and clamp at

a position best for your job. (SE4)

IMPORTANT

6. Set up

SE1

[HE225F]

[HEZ2500F]

SE2

(A)

(B)

SE3

 13 

 14 

7. Fuel

■ RECOMMENDED MIXING RATIO

GASOLINE 50:OIL 1

• Exhaust emission are controlled by the

fundamental engine parameters and

components(eq., carburation, ignition

timing and port timing) without

addition of any major hardware or the

introduction of an inert material during

combustion.

• These engines are certified to operate on

unleaded gasoline.

• Make sure to use gasoline with a

minimum octane number of 89 RON

(USA/Canada: 87AL)

• If you use a gasoline of a lower octane

value than prescribed, there is a danger

that the engine temperature may rise and

an engine problem such as piston seizing

may consequently occur.

• Unleaded gasoline is recommended to

reduce the contamination of the air for the

sake of your health and the environment.

• Poor quality gasolines or oils may damage

sealing rings, fuel lines or fuel tank of the

engine.

■ HOW TO MIX FUEL

Pay attention to agitation.

1. Measure out the quantities of gasoline

and oil to be mixed.

2. Put some of the gasoline into a clean,

approved fuel container.

3. Pour in all of the oil and agitate well.

4. Pour In the rest of gasoline and agitate

IMPORTANT

• Gasoline is very flammable. Avoid

smoking or bringing any flame or

sparks near fuel. Make sure to stop the

engine and allow it cool before

refueling the unit. Select outdoor bare

ground for fueling and move at least

3m (10ft) away from the fueling point

before starting the engine.

• The RedMax engines are lubricated by oil

specially formulated for air-cooled 2-cycle

gasoline engine use. If RedMax oil is not

available, use an anti-oxidant added

quality oil expressly labeled for air-cooled

2-cycle engine use. (JASO FC GRADE

OIL or ISO EGC GRADE)

• Do not use BIA or TCW (2-stroke water-

cooling type) mixed oil.

WARNING

50:1 MIXING CHART

GASOLINE gal. 1 2345

2-CYCLE OIL fl.oz 2.6 5.2 7.8 10.4 13

GASOLINE liter 1 2345

2-CYCLE OIL ml 20 40 60 80 100

7. Fuel

 15 

again for at least one minute. As some

oils may be difficult to agitate depending

on oil ingredients, sufficient agitation is

necessary for the engine to last long. Be

careful that, if the agitation is insufficient,

there is an increased danger of early

piston seizing due to abnormally lean

mixture.

5. Put a clear indication on the outside of the

container to avoid mixing up with gasoline

or other containers.

6. Indicate the contents on outside of

container for easy identification.

■ FUELING THE UNIT

1. Untwist and remove the fuel cap. Rest the

cap on a dustless place.

2. Put fuel into the fuel tank to 80% of the full

capacity.

3. Fasten the fuel cap securely and wipe up

any fuel spillage around the unit.

1. Select bare ground for fueling.

2. Move at least 10feet (3meters) away

from the fueling point before starting

the engine.

3. Stop the engine before refueling the

unit. At that time, be sure to sufficiently

agitate the mixed gasoline in the

container.

FOR YOUR ENGINE LIFE, AVOID;

1. FUEL WITH NO OIL(RAW GASOLINE) –

It will cause severe damage to the internal

engine parts very quickly.

2. GASOHOL – It can cause deterioration of

rubber and/or plastic parts and disruption

of engine lubrication.

3. OIL FOR 4-CYCLE ENGINE USE – It can

cause spark plug fouling, exhaust port

blocking, or piston ring sticking.

4. Mixed fuels which have been left

unused for a period of one month or

more may clog the carburetor and result

in the engine failing to operate properly.

WARNING

5. In the case of storing the product for a

long period of time, clean the fuel tank

after rendering it empty. Next, activate the

engine and empty the carburetor of the

composite fuel.

6. In the case of scrapping the used mixed

oil container, scrap it only at an authorized

repository site.

As lot details of quality assurance, read the

description in the section Limited Warranty

carefully. Moreover, normal wear and

change in product with no functional

influence are not covered by the warranty.

Also, be careful that, if the usage in the

instruction manual is not observed as to the

mixed gasoline, etc. described therein, it

may not be covered by the warranty.

NOTE

 16 

8. Operation

OP2

(1)

(2)

(3)

OP1

(1)

(2)

(3)

OP3

(4)

(7)

(5)

(6)

OP4

The RedMax stick edgers are designed for edging

lawn in gardens, parks, roadsides and so on.

Before starting the engine, take the operating

position and adjust the handle position and the

wheel height as necessary.

■ ADJUSTING WHEEL HEIGHT

1. Loosen the wing nut and change the wheel

height to obtain desired cutting depth. (OP1)

(1) Deep cut

(2) Shallow cut

(3) Wing nut

2. After adjusting the height, tighten the wing nut

securely.

Tightening Torque: 51~68in-lbs (6~8N.m.)

• Never adjust wheel height with the engine

running.

■ STARTING ENGINE

The cutting head will start rotating upon the

engine starts.

1. Rest the unit on a flat, firm place. Keep the

cutting head off the ground and clear of

surrounding objects as it will start rotating upon

starting of the engine.

2. Push the primer pump several times until

overflown fuel flows out in the clear tube. (OP2)

3. Move the choke lever to the closed position.

(OP3)

4. Set the ignition switch to the “start” position.

While pulling the throttle lever, push the set

button, and release the throttle, then the throttle

lever is in to the “start” position. (OP4)

5. While holding the unit firmly, pull out the starter

rope quickly until engine fires. (OP5)

(1) choke lever (2) close (3) open

(4) ignition switch (5) start (6) stop

(7) throttle set button

WARNING

8. Operation

 17 

• Avoid pulling the rope to its end or returning it by

releasing the knob. Such actions can cause

starter failures.

6. Move the choke lever downward to open the

choke. And restart engine. (OP3)

7. Allow the engine to warm up for a several

minutes before starting operation.

1. When restarting the engine immediately after

stopping it, leave the choke open.

2. Overchoking can make the engine hard to start

due to excess fuel. When the engine failed to

start after several attempts, open the choke and

repeat pulling the rope, or remove the spark plug

and dry it.

■ STOPPING ENGINE (OP4)

1. Release the throttle lever and run the engine for

a half minute.

2. Shift the ignition switch to the STOP position.

• Except for an emergency, avoid stopping the

engine while pulling the throttle lever.

■ ADJUSTING THROTTLE CABLE

• The normal play is 1 or 2mm when measured at

the carburetor side end. Readjust with the cable

adjuster as required. (OP6)

(1) cable adjuster

■ ADJUSTING IDLING SPEED (OP7)

1. When the engine tends stop frequently at idling

mode, turn the adjusting screw clockwise.

2. When the cutting head keeps rotating after

releasing the trigger, turn the adjusting screw

counter-clockwise.

(1) idle adjusting screw

• Warm up the engine before adjusting the idling

speed.

NOTE

IMPORTANT

NOTE

IMPORTANT

OP5

.04 in

(1~2mm)

(1)

OP6

(1)

OP7

 18 

8. Operation

■ HOW TO USE

1 Always wear eye protection such as safety

goggles. Never lean over the rotating cutting

head. Rocks or other debris could be thrown

into eyes and face and cause serious

personal injury.

2 Keep the blade guard and the mad guard

attached in place at all times when the unit is

operated.

3 Before starting a job, check the area and

remove all obstacles and objects that could

be thrown by the blade.

4 Do not adjust the wheel height or try to

remove anything entangled to the blade with

the engine running.

1 Before starting the engine, adjust the wheel

height for desired cutting depth (See page 16).

2 Before starting a job, plan your direction of travel

so that you can always hold the edger on you

right side and can walk on a hard surface as

much as possible.

3When starting to edge, maintain the engine

speed at the level required to perform edging

work, and slowly have the blade cut into the

edge groove.

• Before edging, make sure the area is soft

enough so the blade does not bog down.

• Do not move the edger into the work so fast that

the engine or blade bogs down.

• Do not operate using starting throttle lock. It may

cause unit uncontrolled, and clutch failure.

• Use care indirecting discharge to avoid

bystanders, vehicles, glass, and the like.

• When the blade guard is clogged or blade stuck,

stop the engine and clean it.

NOTE

WARNING

OP8

•Always be sure to stop the engine before inspecting the stick edger for problems or

performing maintenance.

• Never alter the stick edger or take the engine apart.

•When replacing parts, always be sure to use only RedMax products or products which

have been certified by RedMax for use with the RedMax stick edger.

WARNING

9. Maintenance

 19 

■ BE SURE TO CHECK THE FOLLOWING BEFORE USING YOUR STICK EDGER

Item to be checked Response

1 Edging mechanism • See if attachment is loose • Tighten screws and bolts

• Check if edges of blades are dull • Sharpen or replace blades

2 Throttle • Stiff and difficult to move • Repair or replace

3 Throttle wire • Too loose, too tight • Adjust

• Stiff and difficult to move • Repair or replace

4 Engine attachment • See if fittings are loose • Tighten fittings

5 Fuel tank • See if attachment is loose • Tighten screws and bolts

• See if fuel pipe is damaged • Replace

• See if cap packing is damaged • Replace

6 Muffler • See if attachment is loose • Tighten screws and bolts

7 Cutting blade • See if damaged or worn shorter • Replace

than usable length

every every every

25 50 100

system/compornent procedure before hours hours hours note

use after after after

fuel leaks, fuel spillage wipe out ✔

fuel tank, air filter, fuel filter inspect/clean ✔✔ replace, if necessary

see

■ADJUSTING

replace carburetor

idle adjusting screw ✔

IDLING SPEED (p.17)

if necessary

clean and readjust

GAP: .025in(0.6~0.7mm)

spark plug ✔

plug gap replace, if necessary

cylinder fins, intake air cooling vent clean ✔

muffler, spark arrester, cylinder exhaust port

clean ✔

throttle lever, ignition switch check operation ✔

replace if

cutting parts ✔

something's wrong

gear case grease ✔

screws/nuts/bolts tighten/replace ✔✔not adjusting screws

drive shaft grease ✔

cutting blade inspect/replace ✔ replace, if necessary

ENGINE

SHAFT

■ MAINTENANCE CHART

Maintenance, replacement, or repair of the emission control device and systems may be

performed by any non-road engine repair establishment or individual.

 20 

•Make sure that the engine has stopped and is

cool before performing any service to the

machine. Contact with moving cutting head

or hot muffler may result in a personal injury.

■ AIR FILTER

• The air filter, if clogged, will reduce the engine

performance. Check and clean the filter element

in warm, soapy water as required. Dry

completely before installing. If the element is

broken or shrunk, replace with a new one. (MA1)

(1) air filter

■ FUEL FILTER

• When the engine runs short of fuel supply, check

the fuel cap and the fuel filter for blockage.

(MA2)

(1) fuel filter

■ SPARK PLUG

• Starting failure and mis-firing are often caused

by a fouled spark plug. Clean the spark plug and

check that the plug gap is in the correct range.

For a replacement plug, use the correct type

specified by RedMax. (MA3)

• REPLACEMENT PLUG:

HE225F: Champion RCJ6Y

HEZ2500F: NGK CMR7A

• Note that using any spark plug other than those

designated may result in the engine failing to

operate properly or in the engine becoming

overheated and damaged.

• To install the spark plug, first turn the plug until it

is finger tight, then tighten it a quarter turn more

with a socket wrench.

87~104 in-lbs

TIGHTENING TORQUE:

(9.8~11.8 N.m.)

IMPORTANT

WARNING

9. Maintenance

(1)

MA2

(1)

MA1

.025 in

0.655mm

MA3

La page charge ...

RedMax HE225F Manuel utilisateur

Marque: RedMax

Modèle: HE225F

Catégorie: Coupe-herbe

Taper: Manuel utilisateur

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: RedMax HE225F User manual

RedMax HE225F Manuel utilisateur

Ce manuel convient également à

RedMax HE225F Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents