Homelite UT33650 Le manuel du propriétaire

Marque: Homelite

Modèle: UT33650

Catégorie: Coupe-herbe

Taper: Le manuel du propriétaire

Ce manuel convient également à

OPERATOR’S MANUAL

MANUEL D’UTILISATION

MANUAL DEL OPERADOR

26CC STRING TRIMMERS

TAILLE-BORDURES À LIGNE

26 CC

RECORTADORAS DE HILO

26 CC

ALL VERSIONS

TOUTES LES VERSIONS

TODAS LAS VERSIONES

26CS

UT33600

26SS

UT33650

Your string trimmer has been engineered and manufactured to Homelite’s high standard for dependability, ease of operation,

and operator safety. When properly cared for, it will give you years of rugged, trouble-free performance.

WARNING: To reduce the risk of injury, the user must read and understand the operator’s manual before

using this product.

Thank you for buying a Homelite product.

GUARDE ESTE MANUAL PARA

FUTURAS CONSULTAS

CONSERVER CE MANUEL POUR

FUTURE RÉFÉRENCE

To register your Homelite product, please visit:

http://register.homelite.com/

Pour enregistrer votre produit de Homelite, s’il vous

plaît la visite: http://register.homelite.com/

Para registrar su producto de Homelite, por favor visita:

http://register.homelite.com/

Cette taille-bordures à ligne a été conçue et fabriquée conformément

aux strictes normes de fiabilité, simplicité d’emploi et sécurité

d’utilisation de Homelite. Correctement entretenue, elle vous

donnera des années de fonctionnement robuste et sans problème.

AVERTISSEMENT : Pour réduire les risques de

blessures, l’utilisateur doit lire et veiller à bien comprendre le

manuel d’utilisation avant d’employer ce produit.

Merci d’avoir acheté un produit Homelite.

Su recortadora de hilo ha sido diseñada y fabricada de

conformidad con las estrictas normas de Homelite para brindar

fiabilidad, facilidad de uso y seguridad para el operador. Con el

debido cuidado, le brindará muchos años de sólido y eficiente

funcionamiento.

ADVERTENCIA: Para reducir el riesgo de lesiones,

el usuario debe leer y comprender el manual del operador antes

de usar este producto.

Le agradecemos la compra de un producto Homelite.

SAVE THIS MANUAL FOR FUTURE REFERENCE

NOTICE AVIS AVISO

Do not use E15 or E85 fuel (or fuel containing greater than 10% ethanol) in this product. It is a viola-

tion of federal law and will damage the unit and void your warranty.

Ne pas utiliser d’essence E15 ou E85 (ou un carburant contenant plus de 10 % d’éthanol) dans ce

produit. Une telle utilisation représente une violation de la loi fédérale et endommagera l’appareil et annulera la garantie.

No utilice combustibles E15 o E85 (ni combustibles que contengan más de 10 % de etanol) con este producto. Esto constituye

una violación a la ley federal, dañará la unidad y anulará la garantía.

See this fold-out section for all of the figures

referenced in the operator’s manual.

Consulter l’encart à volets afin d’examiner

toutes les figures mentionnées dans le manuel

d’utilisation.

Consulte esta sección desplegable para ver todas

las figuras a las que se hace referencia en el

manual del operador.

iii

A - Dual line string head (tête de cordon à ligne double, cabezal del hilo doble)

B - Trimmer shaft (arbre du taille-bordures, eje de la recortadora)

C - Front handle (poignée avant, mango delantero)

D - Power head shaft (arbre du bloc moteur, eje del cabezal motor)

E - Starter grip and rope (poignée du lanceur et corde, mango del arrancador y cuerda)

F - Muffler (silencieux, silenciador)

G - Stop switch (commutateur d’arrêt, interruptor del apagado)

H - Primer bulb (poire d’amorçage, bomba de cebado)

I - Fuel cap (bouchon de carburant, tapa del tanque)

J - Choke lever (levier de volet de départ, palanca de arranque)

K - Throttle trigger (gâchette d’accélérateur, gatillo del acelerador)

L - Curved shaft grass deflector (déflecteur d’herbe d’arbre courbe, deflector de pasto del eje curvo)

M- Straight shaft grass deflector (déflecteur d’herbe d’arbre droit, deflector de pasto para eje recto)

N - Hex key (not shown) (clé hexagonale [non illustré], llave hexagonal [no se muestra])

Fig. 1

26CS

Fig. 2

A - Front handle (poignée avant, mango delantero)

B - Washer (rondelle, arandela)

C - Wing nut (écrou à oreilles, tuerca de mariposa)

D - Bolt (boulon, perno)

A - Wing nut (écrou à oreilles, tuerca de

mariposa)

B - Washer (rondelle, arandela)

C - Bolt (boulon, perno)

D - Grass deflector (déflecteur d’herbe, deflector

de pasto)

E - Bracket (support, soporte)

Fig. 3

26SS

A - Gear head (carter d’engrenages, cabezal de

engranajes)

B - Slot (fente, ranura)

C - Square tab (languette carrée, orejeta

cuadrada)

D - Wing nut (écrou à oreilles, tuerca de

mariposa)

E - Mounting bracket (support de montage,

soporte de montaje)

F - Trimmer shaft (arbre du taille-bordures, eje

de la recortadora)

G - Screw (vis, tornillo)

H - Pin (axe, pasador)

I - Grass deflector (déflecteur d’herbe, deflector

de pasto)

Fig. 4

RUN

START

RUN

START

A - Throttle trigger (gâchette d’accélérateur,

gatillo del acelerador)

B - Starter grip and rope (poignée du lanceur et

corde, mango del arrancador y cuerda)

C - Stop switch (commutateur d’arrêt, interruptor

del apagado)

D - Primer bulb (poire d’amorçage, bomba de

cebado)

E - Choke lever (levier de volet de départ,

palanca de arranque)

Fig. 7

PROPER OPERATING

POSITION

BONNE POSITION

DE TRAVAIL

POSICIÓN

CORRECTA PARA

EL MANEJO DE LA

HERRAMIENTA

26CS

26SS

Fig. 8

Fig. 9

A - Curved shaft trimmer (taille-bordures à

arbre courbe, recortadora de eje curvo)

B - Dangerous cutting area (zone de coupe

dangereuse, área peligrosa de corte)

C - Best cutting area (zone d’efficacité

maximum, mejor área de corte)

D - Direction of rotation (sens de rotation,

sentido de rotación)

A - Trimmer shaft (arbre du taille-bordures,

eje de la recortadora)

B - Power head shaft (arbre du bloc moteur,

eje del cabezal motor)

C - Hex head screws (boulons à six pans,

tornillos de cabeza hexagonal)

D - Indentations (indentations, muescas)

E - Hex key (clé hexagonale, llave hexagonal)

F - Tighten (serrer, ajustar)

G - Loosen (desserrer, aflojar)

A - Start position (position de volet de départ

ouvert, posición de arranque)

B - Run position (position de marche, posición

de marcha)

C - Choke lever (levier de volet de départ,

palanca de arranque)

Fig. 5

Fig. 6

A - Straight shaft trimmer (taille-bordures à

arbre droit, recortadora de eje recto)

B - Dangerous cutting area (zone de coupe

dangereuse, área peligrosa de corte)

C - Best cutting area (zone d’efficacité

maximum, mejor área de corte)

D - Direction of rotation (sens de rotation,

sentido de rotación)

Fig. 13

A - Spool (bobine, carrete)

B - Eyelets (oeillets, ojillos)

Fig. 15

A - Idle speed screw (vis de ralenti, tornillo de

ajuste de la velocidad en vacío)

B - Air filter cover (couvercle du filtre à air, tapa

del filtro de aire)

A - Pull strings (tirer vers l’extérieur, tira del

hilo)

Fig. 14

Fig. 11

A - Spool retainer (retenue de bobine, retén del

carrete)

Fig. 12

A - Eyelet (œillet, ojillo)

B - Arrow on spool (flèche sur la bobine, flecha

en el carrete)

A - Straight shaft trimmer line cut-off blade

(lame de sectionnement de ligne du taille-

bordures à arbre droit, cuchilla de corte de

hilo de la recortadora de eje recto)

B - Curved shaft trimmer line cut-off blade

(lame de sectionnement de ligne du taille-

bordures à arbre courbe, cuchilla de corte

de hilo de la recortadora de eje recto)

Fig. 10

Fig. 17

A - Latch (loquet, pestillo)

B - Air filter cover (couvercle du filtre à air, tapa

del filtro de aire)

C - Slots (fentes, ranuras)

A - Latches (loquets, pestillos)

B - Air filter (filtre à air, filtro de aire)

C - Air filter cover (couvercle du filtre à air, tapa

del filtro de aire)

D - Slots (fentes, ranuras)

Fig. 16

Page / Página 2

 Introduction ......................................................................................................................................................................2

Introduction / Introducción

 General Safety Rules ........................................................................................................................................................ 3

Règles de sécurité générales / Reglas de seguridad generales ........................................................................................................ 3-4

Specific Safety Rules ........................................................................................................................................................ 4

Règles de sécurité particulières / Reglas de seguridad específicas

Symbols ............................................................................................................................................................................ 5

Symboles / Símbolos

 Features ............................................................................................................................................................................6

Caractéristiques / Características

 Assembly .......................................................................................................................................................................6-7

Assemblage / Armado

 Operation ..................................................................................................................................................................... 8-10

Utilisation / Funcionamiento

 Maintenance ..............................................................................................................................................................10-12

Entretien / Mantenimiento .................................................................................................................................................. 10-12 / 10-13

 Troubleshooting .............................................................................................................................................................. 13

Dépannage / Corrección de problema......................................................................................................................................... 13 / 14

 Warranty ......................................................................................................................................................................... 14

Garantie / Garantía ....................................................................................................................................................................... 14 / 15

 Parts Ordering and Service ...............................................................................................................................Back Page

Commande de pièces et réparation / Pedidos de piezas y servicio................................................. Page arrière / Pág. posterio

TABLE OF CONTENTS

TABLE DES MATIÈRES / ÍNDICE DE CONTENIDO

This product has many features for making its use more pleasant and enjoyable. Safety, performance, and dependability

have been given top priority in the design of this product making it easy to maintain and operate.

* * *

Ce produit offre de nombreuses fonctions destinées à rendre son utilisation plus plaisante et satisfaisante. Lors de la

conception de ce produit, l’accent a été mis sur la sécurité, les performances et la fiabilité, afin d’en faire un outil facile à

utiliser et à entretenir.

* * *

Este producto ofrece numerosas características para hacer más agradable y placentero su uso. En el diseño de este producto

se ha conferido prioridad a la seguridad, el desempeño y la fiabilidad, por lo cual se facilita su manejo y mantenimiento.

INTRODUCTION

INTRODUCTION / INTRODUCCIÓN

Page 3 — English

GENERAL SAFETY RULES

WARNING:

Read and understand all instructions. Failure to follow

all instructions listed below may result in electric shock,

fire and/or carbon monoxide poisoning which will cause

death or serious personal injury.

READ ALL INSTRUCTIONS

 For safe operation, read and understand all instructions

before using this product. Follow all safety instructions.

Failure to follow all safety instructions listed below, can

result in serious personal injury.

 Do not allow children or untrained individuals to use this

unit.

 Do not start or operate the engine in a confined space,

building, near open windows, or in other unventilated

space where dangerous carbon monoxide fumes can

collect. Carbon monoxide, a colorless, odorless, and

extremely dangerous gas, can cause unconsciousness

or death.

Clear the work area before each use. Remove all objects

such as rocks, broken glass, nails, wire, or string which

can be thrown or become entangled in the cutting line

or blade.

 Always wear eye protection with side shields marked to

comply with ANSI Z87.1, along with hearing protection.

Failure to do so could result in objects being thrown into

your eyes and other possible serious injuries.

Wear heavy, long pants, long sleeves, boots, and gloves.

Do not wear loose fitting clothing, short pants, sandals,

or go barefoot. Do not wear jewelry of any kind.

Product users on United States Forest Service land, and

in some states, must comply with fire prevention regula-

tions. This product is equipped with a spark arrestor;

however, other user requirements may apply. Check with

your federal, state, or local authorities.

Never operate this unit on the operator’s left side.

Secure long hair above shoulder level to prevent entangle-

ment in moving parts.

Keep all bystanders, children, and pets at least 50 ft. away.

Bystanders should be encouraged to wear eye protection.

Do not operate this unit when you are tired, ill, upset, or

under the influence of alcohol, drugs, or medication.

Do not operate in poor lighting.

Keep firm footing and balance. Do not overreach. Over-

reaching can result in loss of balance or exposure to hot

surfaces. Keep cutting attachment below waist.

 To avoid hot surfaces, never operate the unit with the

bottom of the engine above waist level.

Keep all parts of your body away from any moving part.

Do not touch area around the muffler or cylinder of the

unit; these parts get hot from operation.

 Always stop the engine and remove the spark plug wire

before making any adjustments or repairs except for

carburetor adjustments.

 Inspect the unit before each use for loose fasteners, fuel

leaks, etc. Replace any damaged parts before use.

 The string head will rotate during carburetor adjustments.

It has been reported that vibrations from hand-held tools

may contribute to a condition called Raynaud’s Syndrome

in certain individuals. Symptoms may include tingling,

numbness, and blanching of the fingers, usually apparent

upon exposure to cold. Hereditary factors, exposure to

cold and dampness, diet, smoking, and work practices

are all thought to contribute to the development of these

symptoms. It is presently unknown what, if any, vibrations

or extent of exposure may contribute to the condition.

There are measures that can be taken by the operator to

possibly reduce the effects of vibration:

a) Keep your body warm in cold weather. When operating

the unit wear gloves to keep your hands and wrists

warm. It is reported that cold weather is a major factor

contributing to Raynaud’s Syndrome.

b) After each period of operation, exercise to

increase blood circulation.

c) Take frequent work breaks. Limit the amount of

exposure per day.

d) Keep the product well maintained, fasteners

tightened and worn parts replaced.

If you experience any of the symptoms of this condition,

immediately discontinue use and see your physician about

these symptoms.

 Mix and store fuel in a container approved for gasoline.

Do not smoke while fueling or mixing fuel.

 Mix fuel outdoors where there are no sparks or flames.

Wipe up any fuel spillage. Move 30 ft. away from refueling

site before starting engine.

 Stop the engine and allow to cool before refueling or

storing the unit.

 Allow the engine to cool; empty the fuel tank into a con-

tainer approved for gasoline and secure the unit from

moving before transporting in a vehicle.

 Wear your protective equipment and observe all safety

instructions. Be sure the cutting attachment stops turning

when the engine idles. When the unit is turned off make

sure the cutting attachment has stopped before the unit

is set down.

Page 4 — English

 Inspect before use. Replace damaged parts. Make sure

fasteners are in place and secure. Check for fuel leaks.

 Replace string head if cracked, chipped, or damaged

in any way. Be sure the string head is properly installed

and securely fastened. Failure to do so can cause serious

injury.

 Make sure all guards, straps, deflectors, and handles are

properly and securely attached.

 Never use blades, flailing devices, wire, or rope. Use only

the manufacturer’s replacement line in the cutting head.

Do not use any other cutting attachment. To install any

other brand of cutting head to this string trimmer can

result in serious personal injury.

Never operate unit without the grass deflector in place

and in good condition.

 Maintain a firm grip on both handles while trimming. Keep

string head below waist level. Never cut with the string

head located over 30 in. or more above the ground.

 This product is intended for infrequent use by homeown-

ers and other occasional users for such general applica-

tions as trimming light and heavy vegetation, etc. It is not

intended for prolonged use. Prolonged periods of opera-

tion can cause circulatory problems in the user’s hands

due to vibration. For such use, it may be appropriate to

use a product having an anti-vibration feature.

SPECIFIC SAFETY RULES

Page 5 — English

SYMBOLS

The following signal words and meanings are intended to explain the levels of risk associated with this product.

SYMBOL SIGNAL MEANING

DANGER:

Indicates an imminently hazardous situation, which, if not avoided, will result

in death or serious injury.

WARNING:

Indicates a potentially hazardous situation, which, if not avoided, could result

in death or serious injury.

CAUTION:

Indicates a potentially hazardous situation, which, if not avoided, may result in

minor or moderate injury.

NOTICE:

(Without Safety Alert Symbol) Indicates important information not related to an

injury hazard, such as a situation that may result in property damage.

Some of the following symbols may be used on this product. Please study them and learn their meaning for safe

operation of this product.

SYMBOL NAME EXPLANATION

Safety Alert Indicates a potential personal injury hazard.

Read Operator’s Manual

To reduce the risk of injury, user must read and under-

stand operator’s manual before using this product.

Eye and Hearing Protection

Always wear eye protection with side shields marked to

comply with ANSI Z87.1 along with hearing protection

when operating this equipment.

Keep Bystanders Away Keep all bystanders at least 50 ft. away.

Ricochet

Thrown objects can ricochet and result in personal injury

or property damage.

No Blade

Do not install or use any type of blade on a product dis-

playing this symbol.

Hot Surface

To reduce the risk of injury or damage, avoid contact

with any hot surface.

Gasoline and Lubricant

Use unleaded gasoline intended for motor vehicle use

with an octane rating of 87 [(R + M) / 2] or higher. This

product is powered by a 2-cycle engine and requires

pre-mixing gasoline and 2-cycle lubricant.

Page 6 — English

FEATURES

PRODUCT SPECIFICATIONS

Weight (dry)

26CS .....................................................................................................................................................................9.5 lbs.

26SS ...................................................................................................................................................................10.5 lbs.

Cutting width ..................................................................................................................................................................17 in.

Engine displacement .......................................................................................................................................................26cc

Line diameter .............................................................................................................................................................. .080 in.

KNOW YOUR STRING TRIMMER

See Figure 1.

The safe use of this product requires an understanding of

the information on the tool and in this operator’s manual as

well as a knowledge of the project you are attempting. Before

use of this product, familiarize yourself with all operating

features and safety rules.

GRASS DEFLECTOR

The trimmer includes a grass deflector that helps protect

you from flying debris.

REEL-EASY™ TAP ADVANCE SYSTEM

The Reel-Easy™ Tap Advance System allows easy line

advance during trimmer operation.

TOP-MOUNTED MOTOR

The top-mounted motor improves balance and is located

away from the dust and debris of the cutting area.

ASSEMBLY

UNPACKING

This product requires assembly.

 Carefully remove the product and any accessories from

the box. Make sure that all items listed in the packing list

are included.

WARNING:

Do not use this product if any parts on the Packing List

are already assembled to your product when you unpack

it. Parts on this list are not assembled to the product by

the manufacturer and require customer installation. Use

of a product that may have been improperly assembled

could result in serious personal injury.

 Inspect the product carefully to make sure no breakage

or damage occurred during shipping.

 Do not discard the packing material until you have care-

fully inspected and satisfactorily operated the product.

 If any parts are damaged or missing, please call

1-800-242-4672 for assistance.

PACKING LIST

Power Head Shaft

Trimmer Shaft

Front Handle

Hex Key

Curved Shaft Grass Deflector – 26CS

PACKING LIST (continued)

Straight Shaft Grass Deflector – 26SS

Bottle of 2-Cycle Lubricant

Operator’s Manual

WARNING:

If any parts are damaged or missing, do not operate this

product until the parts are replaced. Use of this product

with damaged or missing parts could result in serious

personal injury.

WARNING:

Do not attempt to modify this product or create acces-

sories not recommended for use with this product. Any

such alteration or modification is misuse and could result

in a hazardous condition leading to possible serious

personal injury.

WARNING:

Operation of this equipment could create sparks that

can start fires around dry vegetation. A spark arrestor

may be required. The operator should contact local fire

agencies for laws or regulations relating to fire prevention

requirements.

Page 7 — English

ASSEMBLY

WARNING:

To prevent accidental starting that could cause serious

personal injury, always disconnect the engine spark plug

wire from the spark plug when assembling parts.

FRONT HANDLE

See Figure 2.

 Loosen and remove the wing nut, washer, and bolt from

the handle.

Install the handle on the power head shaft at the location

indicated by the label on the shaft.

Adjust handle up or down, if necessary, to desired operat-

ing position.

Reinstall the bolt, washer, and wing nut. Tighten wing nut

to secure.

 Slightly loosen the wing nut on the handle.

 Rotate the handle on the drive shaft housing at the loca-

tion indicated by the label on the shaft.

 Retighten the wing nut to secure the handle in place.

ATTACHING THE GRASS DEFLECTOR

WARNING:

The line cutting blade on the grass deflector is sharp.

Avoid contact with the blade. Failure to avoid contact

can result in serious personal injury.

TO ATTACH THE CURVED SHAFT GRASS

DEFLECTOR – 26CS

See Figure 3.

 Remove the bolt, washer, and wing nut from grass

deflector.

 Press the grass deflector onto the bottom of the curved

shaft as shown.

 Insert the bolt through the grass deflector and the bracket

on the curved shaft.

 Place the washer on the bolt.

 Place the wing nut on the bolt and tighten securely.

TO ATTACH THE STRAIGHT SHAFT GRASS

DEFLECTOR – 26SS

See Figure 4.

 Remove the wing nut and mounting bracket from the grass

deflector.

 Assemble straight shaft grass deflector to drive shaft so

that the pin in the grass deflector fits in the locator hole

in the lower side of the drive shaft near the gear head.

 Place the mounting bracket over the drive shaft so the

square tab on the mounting bracket fits into the slot in

the straight shaft grass deflector.

 Rotate the mounting bracket so the screw on the grass

deflector goes into the slot on the mounting bracket.

 Reinstall the wing nut and tighten securely.

CONNECTING THE POWER HEAD SHAFT AND

TRIMMER SHAFT

See Figure 5.

 Align the two indentations in the trimmer shaft with the

screws in the power head shaft. Insert the trimmer shaft

into the power head shaft.

 Push the two sections together until the trimmer shaft

stops.

 Using a hex key, turn each of the two screws until securely

tightened.

WARNING:

Be certain the shafts are locked into place before oper-

ating string trimmer; check it periodically for tightness

during use to avoid possible disconnection of shafts,

which could result in serious personal injury.

CAUTION:

Be careful when sliding the two shafts together to avoid

pinching your hands or fingers.

WARNING:

This string trimmer is designed to use only the provided

trimmer shaft and string head. It is not capable of using

other attachments or cutting heads. Attempting to use

other attachments or cutting heads could result in seri-

ous personal injury.

Page 8 — English

WARNING:

Do not allow familiarity with this product to make you

careless. Remember that a careless fraction of a second is

sufficient to inflict serious injury.

WARNING:

Always wear eye protection with side shields marked to

comply with ANSI Z87.1, along with hearing protection.

Failure to do so could result in objects being thrown into

your eyes and other possible serious injuries.

WARNING:

Never use blades, flailing devices, wire, or rope on this prod-

uct. Do not use any attachments or accessories not rec-

ommended by the manufacturer of this product. The use of

attachments or accessories not recommended can result

in serious personal injury.

WARNING:

Operation of this equipment can create sparks that can

start fires around dry vegetation. A spark arrestor may

be required. The operator should contact local fire agen-

cies for laws or regulations relating to fire prevention

requirements.

OXYGENATED FUELS

NOTICE:

Do not use E15 or E85 fuel (or fuel containing greater

than 10% ethanol) in this product. It is a violation of

federal law and will damage the unit and void your

warranty.

Fuel system damage or performance problems resulting

from the use of an oxygenated fuel containing more than

the percentage of oxygenates stated below are not covered

under warranty.

Ethanol. Gasoline containing up to 10% ethanol by volume

(commonly referred to as E10) is acceptable. E15 and E85

are not.

FUELING AND REFUELING THE TRIMMER

WARNING:

Gasoline and its vapors are highly flammable and ex-

plosive. To prevent serious personal injury and property

damage, handle it with care. Keep away from ignition

sources and open flames, handle outdoors only, do not

smoke and wipe up spills immediately.

FUEL MIXTURE

This product is powered by a 2-cycle engine and requires

pre-mixing gasoline and 2-cycle lubricant. Pre-mix unleaded

gasoline and 2-cycle engine lubricant in a clean container

approved for gasoline. DO NOT mix quantities larger than

usable in a 30-day period.

Recommended fuel: This engine is certified to operate on

unleaded gasoline intended for automotive use.

NOTE: We recommend you use Homelite premium 2-cycle

lubricant or an equivalent high-quality synthetic 2-cycle

lubricant in this product. Mix at 2.6 oz. per gallon (US).

Do not use automotive lubricant or 2-cycle outboard

lubricant.

HIGH QUALITY 2-CYCLE ENGINE LUBRICANT

GASOLINE LUBRICANT

1.0 gal. (US) (3.8 liter) 2.6 oz. (76 ml)

FILLING TANK

 Clean surface around fuel cap to prevent contamination.

 Loosen fuel cap slowly. Rest the cap on a clean surface.

 Carefully pour fuel into the tank. Avoid spillage.

 Prior to replacing the fuel cap, clean and inspect the

gasket.

 Immediately replace fuel cap and hand tighten. Wipe up

any fuel spillage.

NOTE: It is normal for smoke to be emitted from a new

engine after first use.

WARNING:

Always shut off engine before fueling. Never add fuel to a

machine with a running or hot engine. Move at least 30 ft.

from refueling site before starting engine. Do not smoke

and stay away from open flames and sparks. Failure to

safely handle fuel could result in serious personal injury.

STARTING AND STOPPING

See Figures 6 - 7.

Trimmer should be on a flat, bare surface for starting.

To start a cold engine:

 Slowly press the primer bulb 10 times.

 Set the choke lever to the START (A) position.

 Squeeze the throttle trigger fully and pull the starter handle

until the engine runs. Do not pull the starter grip more

than six (6) times.

NOTE: Keep throttle trigger squeezed fully through re-

maining steps. If the engine does not start, start over at

the first step with pressing the primer bulb.

OPERATION

Page 9 — English

OPERATION

overheating. If grass becomes wrapped around the string

head, STOP THE ENGINE, disconnect the spark plug wire,

and remove the grass. Prolonged cutting at partial throttle

will result in lubricant dripping from the muffler.

WARNING:

Always hold the string trimmer away from the body keep-

ing clearance between the body and the product. Any

contact with the housing or string trimmer cutting head

can result in burns and/or other serious personal injury.

CUTTING TIPS

See Figures 8 - 9.

 Avoid hot surfaces by always keeping the tool away from

your body. (Proper operating position shown in figure 8.)

Keep the trimmer tilted toward the area being cut; this is

the best cutting area.

The curved shaft trimmer cuts when passing the unit from

right to left. The straight shaft trimmer cuts when passing

the unit from left to right. This will avoid throwing debris at

the operator. Avoid cutting in the dangerous area shown

in figure 9.

 Use the tip of line to do the cutting; do not force string

head into uncut grass.

 Wire and picket fences cause extra line wear, even break-

age. Stone and brick walls, curbs, and wood may wear

line rapidly.

 Avoid trees and shrubs. Tree bark, wood moldings, siding,

and fence posts can easily be damaged by the line.

ADVANCING LINE USING THE REEL-EASY

™

TAP ADVANCE SYSTEM

Line advance is controlled by tapping string head on grass

while running engine at full throttle.

 Run engine at full throttle.

 Tap string head on ground to advance line. Line advances

each time the head is tapped.

 Several taps may be required until line strikes the cut off

blade.

 Resume trimming.

NOTE: If the line is worn too short you may not be able to

advance the line by tapping it on the ground. If so, STOP

THE ENGINE, disconnect the spark plug wire, and manually

advance the line.

 Allow the engine to run for 10 seconds, then set the choke

lever to the RUN (B) position.

To restart a warm engine:

 Slowly press the primer bulb 10 times.

 Set the choke lever to the RUN (B) position.

 Squeeze the throttle trigger fully and pull the starter handle

until the engine runs.

To stop the engine:

 To stop the engine, depress the STOP switch to the stop

position “ ”.

IF ASSISTANCE IS REQUIRED FOR THIS PRODUCT:

Do not return this product to the retail store where it was

purchased. Please call our Customer Service Department

for any issues you may have.

For Help Call: 1-800-242-4672

OPERATING THE TRIMMER

See Figure 8.

WARNING:

Engine housing can become hot during trimmer opera-

tion. Do not rest or place your arm, hand, or any body

part against the engine housing during trimmer operation.

Only hold the trimmer as shown in Figure 8 with all body

parts clear of engine housing. Extended contact with

the engine housing can result in burns or other injuries.

WARNING:

Always position the unit on the operator’s right side. The

use of the unit on the operator’s left side will expose the

operator to hot surfaces and can result in possible burn

injury.

WARNING:

To avoid burns from hot surfaces, never operate unit with

the bottom of the engine above waist level.

Hold the trimmer with your right hand on the rear handle

and your left hand on the front handle. Keep a firm grip with

both hands while in operation. Trimmer should be held at a

comfortable position with the rear handle about hip height.

Always operate trimmer at full throttle. Cut tall grass from the

top down. This will prevent grass from wrapping around the

shaft housing and string head which may cause damage from

Page 10 — English

OPERATION

ADVANCING THE LINE MANUALLY

With the engine off and the spark plug wire disconnected,

push the spool retainer down while pulling on line(s) to manu-

ally advance the line.

GRASS DEFLECTOR LINE TRIMMING CUT-OFF

BLADE

See Figure 10.

The trimmer is equipped with a line trimming cut-off blade on

the grass deflector. For best cutting, advance line until it is

trimmed to length by the cut-off blade. Advance the line when-

ever you hear the engine running faster than normal, or when

trimming efficiency diminishes. This will maintain best perfor-

mance and keep the line long enough to advance properly.

WARNING:

When servicing, use only identical replacement parts.

Use of any other parts could create a hazard or cause

product damage.

WARNING:

Always wear eye protection with side shields marked to

comply with ANSI Z87.1, along with hearing protection.

Failure to do so could result in objects being thrown into

your eyes and other possible serious injuries.

WARNING:

Before inspecting, cleaning, or servicing the machine,

shut off engine, wait for all moving parts to stop, and

disconnect spark plug wire and move it away from spark

plug. Failure to follow these instructions can result in

serious personal injury or property damage.

GENERAL MAINTENANCE

Avoid using solvents when cleaning plastic parts. Most

plastics are susceptible to damage from various types of

commercial solvents and may be damaged by their use.

Use clean cloths to remove dirt, dust, lubricant, grease, etc.

WARNING:

Do not at any time let brake fluids, gasoline, petroleum-

based products, penetrating lubricants, etc., come in con-

tact with plastic parts. Chemicals can damage, weaken or

destroy plastic which could result in serious personal

injury.

You can often make adjustments and repairs described here.

For other repairs, have the trimmer serviced by an authorized

service dealer.

MAINTENANCE

SPOOL REPLACEMENT

REEL-EASY™ TAP ADVANCE SYSTEM

See Figure 11 - 12.

If replacing line only, refer to Line Replacement later in this

manual.

Use only .080 in. diameter trimmer line.

 Stop the engine and disconnect the spark plug wire. Hold

the string head and unscrew the spool retainer.

To remove the spool retainer:

Turn the spool retainer counterclockwise for 26CS.

Turn the spool retainer clockwise for 26SS.

 Remove the empty spool from the string head.

NOTE: It is not necessary to remove the string head

housing from the drive shaft.

 Insert the new spool into the string head.

NOTE: Make sure the arrows on the spool are aligned

with the eyelets in the string head housing. Push down

and hold the spool and housing together while complet-

ing the installation.

 Reinstall the spool retainer to secure.

To install the spool retainer:

Turn the spool retainer clockwise for 26CS.

Turn the spool retainer counterclockwise for 26SS.

 Install line as described in Line Replacement.

LINE REPLACEMENT

See Figures 13 - 14.

 Stop the engine and disconnect the spark plug wire.

 Rotate the spool clockwise as necessary to align the

arrows on the spool with the eyelets in the string head

housing.

 Cut one piece of trimmer line 10 ft. long. Insert the line

into the eyelet on the string trimmer housing. Push until

the end of the line comes out the other side of the string

head. Pull the line from the other side until equal amounts

of line appear on both sides of the spool.

Page 11 — English

 Rotate the spool clockwise to wind the line on the spool

until approximately 6 in. of line is showing on each side.

 Push the spool retainer down while pulling on line(s) to

manually advance the line and to check for proper as-

sembly of the string head.

CLEANING THE EXHAUST PORT, MUFFLER,

AND SPARK ARRESTOR

NOTE: Depending on the type of fuel used, the type and

amount of lubricant used, and/or your operating conditions, the

exhaust port, muffler, and/or spark arrestor screen may be-

come blocked with carbon deposits. If you notice a power

loss with your gas powered tool, you may need to remove

these deposits to restore performance. We highly recom-

mend that only qualified service technicians perform this

service.

The spark arrestor must be cleaned or replaced every 50

hours or yearly to ensure proper performance of your prod-

uct. Spark arrestors may be in different locations depending

on the model purchased. Please contact your nearest service

dealer for the location of the spark arrestor for your model.

IDLE SPEED ADJUSTMENT

See Figure 15.

WARNING:

The cutting head will move when adjusting the idle speed.

Wear all protective clothing and keep all bystanders,

children, and pets at least 50 ft. away. Make adjustments

with the unit supported by hand so that the cutting head

does not contact the ground or any object. Keep all parts

of your body away from the cutting head and muffler.

Failure to follow these instructions could result in serious

personal injury.

If the cutting attachment turns at idle, the idle speed screw

needs adjusting on the engine. Turn the idle speed screw

counterclockwise to reduce the idle RPM and stop the cut-

ting attachment movement. If the cutting attachment still

moves at idle speed, contact a service dealer for adjustment

and discontinue use until the repair is made.

WARNING:

The cutting attachment should never turn at idle. Turn

the idle speed screw counterclockwise to reduce the

idle RPM and stop the cutting attachment, or contact a

service dealer for adjustment and discontinue use until

the repair is made. Serious personal injury could result

from the cutting attachment turning at idle.

CLEANING THE AIR FILTER

See Figures 16 - 17.

For proper performance and long life, keep air filter clean.

 Remove the air filter cover by pushing down on the latches

while gently pulling off the cover.

 Remove the air filter.

 Clean the foam filter element with warm soapy water.

Rinse and let dry.

NOTE: If the foam filter element is damaged, it should be

replaced.

 Apply a light coat of engine oil to the foam filter element,

then squeeze it out.

 Reinstall the air filter.

NOTE: Make sure the filter is seated properly inside the

cover. Installing the filter incorrectly will allow dirt to enter

the engine, causing rapid engine wear.

 Replace the air filter cover by placing the slots on the air

filter cover over the latches on the housing, then push

the cover down until it snaps securely in place.

FUEL CAP, TANK, AND LINES

WARNING:

Check for fuel leaks. A leaking fuel cap, tank, or lines

are a fire hazard and must be replaced immediately. If

you find any leaks, correct the problem before using the

product. Failure to do so could result in a fire that could

cause serious personal injury.

The fuel cap contains a non-serviceable filter and a check

valve. A clogged fuel filter will cause poor engine perfor-

mance. If performance improves when the fuel cap is loos-

ened, check valve may be faulty or filter clogged. Replace

fuel cap if required.

SPARK PLUG REPLACEMENT

This engine uses a Champion RCJ-6Y or Torch L7RTC spark

plug with .025 in. electrode gap. Use an exact replacement

and replace annually.

NOTICE:

Be careful not to cross-thread the spark plug. Cross-

threading will seriously damage the product.

MAINTENANCE

Page 12 — English

MAINTENANCE

STORING THE PRODUCT

 Clean all foreign material from the product. Store idle unit

indoors in a dry, well-ventilated area that is inaccessible

to children. Keep away from corrosive agents such as

garden chemicals and de-icing salts.

 Abide by all ISO and local regulations for the safe storage

and handling of gasoline.

When storing 1 month or longer:

 Drain all fuel from tank into a container approved for

gasoline. Run engine until it stops.

HIGH ALTITUDE ENGINE OPERATION

Please have an authorized service center adjust this engine

if it is to be run above 2000 feet. Failure to do so may result

in poor engine performance and increased emissions. An

engine adjusted for high altitudes can not be run at 2000

feet or lower. In doing so, the engine will overheat and cause

serious engine damage. Please have an authorized service

center restore high altitude modified engines to the original

factory specification before operating below 2000 feet.

THIS PRODUCT WAS MANUFACTURED WITH A CATALYST MUFFLER

Congratulations! You have made an investment toward protecting the environment. In order to maintain this product’s

original emission level, please refer to the maintenance section below.

MAINTENANCE SCHEDULE

Inspect For Clean Replace Replace

Maintenance Damage Before Every Every 25 Hours Every

Part Each Use 5 Hours or Yearly 50 Hours

* CATALYTIC MUFFLER ASSEMBLY..................................................................................................................X

SPARK SCREEN ...............................................................................................................................................X

* AIR FILTER ASSY

includes:

Filter Screen ........................................................................ X

* CARBURETOR ASSY

includes:

Gaskets ........................................ X

* FUEL TANK ASSY

includes:

Fuel Lines ..................................... X

Fuel Cap ....................................... X

Fuel Filter................................................................................................................... X

* IGNITION ASSY

includes:

Spark Plug ................................................................................................................. X

* NOTICE: THE USE OF EMISSION CONTROL COMPONENTS OTHER THAN THOSE DESIGNED FOR THIS UNIT

IS A VIOLATION OF FEDERAL LAW.

Page 13 — English

TROUBLESHOOTING

Problem Possible Cause Solution

1. Clean or replace spark plug. Reset spark plug

gap. Refer to Spark Plug Replacement earlier

in this manual.

2. Push primer bulb until bulb is full of fuel. If bulb

does not fill, primary fuel delivery system is

blocked. Contact an authorized service dealer. If

primer bulb fills, engine may be flooded, proceed

to next item.

3. Set the CHOKE lever to the START position.

Squeeze the trigger and pull the rope repeatedly

until the engine starts and runs.

NOTE: Depending on the severity of the flooding,

this may require numerous pulls of the rope.

1. Use fresh fuel and the correct 2-cycle lubricant

mix. (50:1).

2. Clean air filter screen. Refer to Cleaning Air

Filter earlier in this manual.

3. Contact an authorized servicing dealer.

4. Clean or replace spark plug. Reset spark plug

gap. Refer to Spark Plug Replacement earlier

in this manual.

1. Turn idle speed screw clockwise to increase idle

speed. See Figure 15.

1. Lubricate line with silicone spray.

2. Install more line. Refer to the applicable line

replacement section in this manual.

3. Pull lines while alternately pressing down on and

releasing spool retainer.

4. Remove line from spool and rewind. Refer to

the applicable line replacement section in this

manual.

5. Advance line at full throttle.

Engine will not start

Engine does not reach full

speed and emits excessive

smoke

Engine starts, runs, and

accelerates but will not idle

Line will not advance

1. No spark.

2. No fuel.

3. Engine is flooded.

1. Incorrect lubricant/fuel mixture.

2. Air filter is dirty.

3. Spark arrestor screen is dirty.

4. Spark plug fouled.

1. Idle speed screw on carburetor

needs adjustment.

1. Line is welded to itself.

2. Not enough line on spool.

3. Line is worn too short.

4. Line is tangled on spool.

5. Engine speed is too slow.

1. Clean threads and lubricate with grease - if no

improvement, replace the spool retainer.

1. Cut tall grass from the top down to prevent

wrapping.

2. Operate trimmer at full throttle.

1. Reassemble shafts. Refer to Connecting the

Power Head Shaft and Trimmer Shaft in the

Assembly section of this manual.

Spool retainer hard to turn

Grass wraps around drive

shaft housing and string

head

Engine starts and runs but

string head does not turn

1. Screw threads are dirty or

damaged.

1. Cutting tall grass at ground level.

2. Operating trimmer at part throttle.

1. Shafts are incorrectly assembled.

Page 14 — English

WARRANTY

LIMITED WARRANTY STATEMENT

Homelite Consumer Products, Inc., (“Homelite”) warrants

to the original retail purchaser that this HOMELITE brand

outdoor product is free from defect in material and

workmanship and agrees to repair or replace, at Homelite’s

discretion, any defective product free of charge within these

time periods from the date of purchase.

 Two years for all models if used for personal, family, or

household use;

 90 days for any unit used for other purposes, such as

rental or commercial.

This warranty extends to the original retail purchaser

only and commences on the date of the original retail

purchase.

Any part of the this product manufactured or supplied

by Homelite and found in the reasonable judgment of

Homelite to be defective in material or workmanship will

be repaired or replaced without charge for parts and labor

by a Homelite authorized service center.

The product, including any defective part, must be returned

to an authorized service dealer within the warranty period.

The expense of delivering the product to the dealer for

warranty work and the expense of returning it back to the

owner after repair or replacement will be paid by the owner.

Homelite’s responsibility in respect to claims is limited to

making the required repairs or replacements and no claim

of breach of warranty shall be cause for cancellation or

rescission of the contract of sale of any HOMELITE brand

product. Proof of purchase will be required by the dealer

to substantiate any warranty claim. All warranty work must

be performed by a Homelite authorized service center.

This warranty is limited to ninety (90) days from the date of

original retail purchase for any HOMELITE brand product

that is used for rental or commercial purposes, or any other

income-producing purpose.

This warranty does not cover any HOMELITE brand product

that has been subject to misuse, neglect, negligence, or

accident, or that has been operated in any way contrary

to the operating instructions as specified in this operator’s

manual. This warranty does not apply to any damage to

the product that is the result of improper maintenance or

to any product that has been altered or modified. The

warranty does not extend to repairs made necessary

by normal wear or by the use of parts or accessories

which are either incompatible with the HOMELITE

brand product or adversely affect its operation,

performance, or durability. In addition, this warranty does

not cover:

A. Tune-ups – Spark Plugs, Carburetor, Carburetor

Adjustments, Ignition, Filters

B. Wear items – Bump Knobs, Outer Spools, Cutting

Lines, Inner Reels, Starter Pulleys, Starter Ropes, Drive

Belts, Tines, Felt Washers, Hitch Pins, Mulching Blades,

Blower Fans, Blower and Vacuum Tubes, Vacuum Bags

and Straps, Guide Bars, Saw Chains

Homelite reserves the right to change or improve

the design of any HOMELITE brand product without

assuming any obligation to modify any product previously

manufactured.

ALL IMPLIED WARRANTIES ARE LIMITED IN DURATION

TO THE STATED WARRANTY PERIOD. ACCORDINGLY,

ANY SUCH IMPLIED WARRANTIES INCLUDING

MERCHANTABILITY, FITNESS FOR A PARTICULAR

PURPOSE, OR OTHERWISE, ARE DISCLAIMED IN

THEIR ENTIRETY AFTER THE EXPIRATION OF THE

APPROPRIATE TWO-YEAR OR NINETY-DAY WARRANTY

PERIOD. HOMELITE’S OBLIGATION UNDER THIS

WARRANTY IS STRICTLY AND EXCLUSIVELY LIMITED

TO THE REPAIR OR REPLACEMENT OF DEFECTIVE

PARTS AND HOMELITE DOES NOT ASSUME OR

AUTHORIZE ANYONE TO ASSUME FOR THEM ANY

OTHER OBLIGATION. SOME STATES DO NOT ALLOW

LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY

LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY

TO YOU. HOMELITE ASSUMES NO RESPONSIBILITY

FOR INCIDENTAL, CONSEQUENTIAL, OR OTHER

DAMAGES INCLUDING, BUT NOT LIMITED TO, EXPENSE

OF RETURNING THE PRODUCT TO AN AUTHORIZED

HOMELITE SERVICE CENTER AND EXPENSE OF

DELIVERING IT BACK TO THE OWNER, MECHANIC’S

TRAVEL TIME, TELEPHONE OR TELEGRAM CHARGES,

RENTAL OF A LIKE PRODUCT DURING THE TIME

WARRANTY SERVICE IS BEING PERFORMED, TRAVEL,

LOSS OR DAMAGE TO PERSONAL PROPERTY, LOSS

OF REVENUE, LOSS OF USE OF THE PRODUCT, LOSS

OF TIME, OR INCONVENIENCE. SOME STATES DO NOT

ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL

OR CONSEQUENTIAL DAMAGES, SO THE ABOVE

LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.

This warranty gives you specific legal rights, and you may

also have other rights which vary from state to state.

This warranty applies to all HOMELITE brand products

manufactured by or for Homelite and sold in the United

States and Canada.

To locate your nearest Homelite authorized service

center, dial 1-800-242-4672 or log on to our website at

www.homelite.com.

Page 3 — Français

RÈGLES DE SÉCURITÉ GÉNÉRALES

AVERTISSEMENT :

Lire et veiller à bien comprendre toutes les

instructions. Le non-respect de toutes les instructions

ci-dessous peut entraîner un choc électrique, un

incendie et/ou intoxication au monoxyde de carbone qui

causant des blessures graves ou mortelles.

LIRE TOUTES LES INSTRUCTIONS

 Pour travailler en toute sécurité, lire et veiller à bien

comprendre toutes les instructions avant d’utiliser ce

produit. Respecter toutes les instructions de sécurité.

Le non respect des instructions de sécurité ci-dessous

peut entraîner des blessures graves.

 Ne pas laisser des enfants ou personnes n’ayant pas reçu

une formation adéquate utiliser cet outil.

 Ne pas démarrer ou faire tourner le moteur dans un

espace confine, de bâtiment, à proximité des fenêtres

ouverts, autre ou des zones sans ventilation où des

vapeurs toxiques de monoxyde de carbone peuvent

s’accumuler. Le monoxyde de carbone, un gaz incolore,

inodore et extrêmement toxique peut causer une perte

de conscience et être mortel.

 Déblayer la zone de travail avant chaque utilisation. La

débarrasser de tous les objets tels que cailloux, verre

brisé, clous, fils métalliques, cordes, etc. risquant d’être

projetés ou de se prendre dans la ligne de coupe ou la

lame.

 Toujours porter une protection oculaire avec écrans

latéraux certifiée conforme à la norme ANSI Z87.1 ainsi

qu’un protection auditive lors de l’utilisation de ce produit.

 Porter des pantalons longs, manches longues, des

chaussures de travail et des gants épais. Ne pas porter

de vêtements amples, bijoux, shorts, sandales et ne pas

travailler pieds nus. Ne porter aucun bijou.

 Les produits utilisés sur les territoires des services

forestiers des États-Unis et de certains états doivent être

conformes aux réglementations de lutte contre l’incendie.

Cet outil est doté d’un pare-étincelles, toutefois, d’autres

dispositifs peuvent être requis. Consulter les autorités

locales et gouvernementales.

 Ne jamais utiliser cet outil en le tenant du côté gauche.

 Attacher les cheveux longs pour les maintenir au-dessus

des épaules, afin qu’ils ne se prennent pas dans les

pièces en mouvement.

 Garder les badauds, enfants et animaux à une distance

de 15 m (50 pi) minimum. Recommander aux personnes

présente de porter une protection oculaire.

 Ne pas utiliser ce taille-bordures en état de fatigue, si l’on

est souffrant ou sous l’influence de l’alcool, de drogues

ou de médicaments.

 Ne pas travailler sous un éclairage insuffisant.

 Se tenir bien campé et en équilibre. Ne pas travailler

hors de portée. Le travail hors de portée risque de faire

perdre l’équilibre ou de causer un contact avec les pièces

brûlantes. Gardez le dispositif de coupe sous la taille.

 Garder toutes les parties du corps à l’écart des pièces

en mouvement.

 Pour éviter le contact avec les parties brûlantes, ne jamais

travailler avec le bas du moteur au-dessus du niveau de

la taille.

Ne pas utiliser cet outil en état de fatigue, si l’on est

souffrant ou contrarié ou sous l’influence de l’alcool, de

drogues ou de médicaments.

 Toujours arrêter le moteur et débrancher le fil de la bougie

avant d’effectuer tout entretien ou réglage, à l’exception

des réglages du carburateur.

 Inspecter l’outil avant chaque utilisation pour s’assurer

qu’il n’y a pas de pièces desserrées, de fuites ce

carburant, etc. Remplacer les pièces endommagées

avant utilisation.

 La tête de coupe tourne pendant le réglage du carburateur.

 Il a été rapporté que, chez certaines personnes, les

vibrations produites par les outils à main motorisés peuvent

contribuer au développement d’une affection appelée

syndrome de Raynaud. Les symptômes peuvent inclure

des picotements, l’insensibilisation et le blanchissement

des doigts et sont habituellement provoqués par

l’exposition au froid. L’hérédité, l’exposition au froid et à

l’humidité, le régime alimentaire, la fumée et les habitudes

de travail sont tous des facteurs considérés comme

contribuant au développement de ces symptômes. Il

n’existe actuellement aucune preuve qu’un certain type

de vibration ou le degré d’exposition contribue réellement

au développement de cette affectation. Certaines

mesures, susceptibles de réduire les effets des vibrations,

peuvent être prises par l’opérateur :

a) Garder le corps au chaud par temps froid. Pendant

l’utilisation, porter des gants afin de tenir les

mains et les poignets au chaud. Il a été établi

que le froid est l’une des principales causes du

symptôme de Raynaud.

b) Après chaque période d’utilisation, faire des

exercices pour accroître la circulation.

c) Faire des pauses fréquentes. Limiter la durée

d’exposition quotidienne.

d) Garder le produit bien entretenu, toutes les pièces

de boulonnerie serrées et remplacer les pièces

usées.

En cas d’apparition de l’un ou plusieurs des symptômes

décrits ci-dessus, cesser d’utiliser l’outil et consulter un

médecin.

Page 4 — Français

 Inspecter l’outil avant chaque utilisation. Remplacer les

pièces endommagées. S’assurer que toutes les pièces

de boulonnerie sont en place et bien serrées. S’assurer

de l’absence de fuites de carburant.

 Si la tête de coupe est fendue, brisée ou endommagée

de quelque façon que ce soit, la remplacer. S’assurer que

la tête de coupe est correctement installée et solidement

assujettie. S’il ne le sont pas, l’opérateur court des risques

de blessures graves.

 S’assurer que tous les dispositifs de protection,

déflecteurs et poignées sont correctement installés et

solidement assujettis.

 Ne jamais utiliser de lames ou de dispositifs à fléau, fil

et cordes. Utiliser exclusivement des lignes de coupe

d’origine. Ne pas utiliser d’autres accessoires de coupe.

L’utilisation d’une tête de coupe d’autre marque sur ce

taille-bordures peut entraîner des blessures graves.

 Ne jamais utiliser l’outil si le déflecteur d’herbe n’est pas

en place et en bon état.

 Tenir fermement les deux poignées pendant le travail.

Tenir la tête de coupe au-dessous du niveau de la taille.

Ne jamais tailler avec la tête de coupe à plus de 762 mm

(30 po) du sol.

 Ce produit est conçu pour les personnes qui prévoient

l’utiliser de manière peu fréquente pour des applications

générales par exemple, tailler la végétation faible et dense

etc.; l’outil peut également convenir à d’autres utilisateurs

occasionnels. Elle n’est pas conçue pour un usage

prolongé. Les périodes d’utilisation prolongée peuvent

entraîner des problèmes circulatoires dans les mains

de l’opérateur, causés par les vibrations. Pour ce type

d’application, il peut être bon d’utiliser une scie équipée

d’un dispositif anti-vibrations.

RÈGLES DE SÉCURITÉ PARTICULIÈRES

RÈGLES DE SÉCURITÉ GÉNÉRALES

 Mélanger et conserver le carburant dans un bidon ou

jerrycan approuvé pour l’essence. Ne pas fumer pendant

le ravitaillement en carburant ou de mélange de carburant.

 Mélanger le carburant à l’extérieur, loin de toute flamme

ou source d’étincelles. Essuyer tout carburant répandu.

S’éloigner de 9 m (30 pi) du point d’approvisionnement

avant de lancer le moteur.

 Arrêter le moteur et le laisser refroidir avant de faire le

plein ou de le remiser.

 Pour le transport dans un véhicule, le réservoir doit être

vidé dans un bidon ou jerrycan approuvé pour l’essence

et l’outil bien arrimé.

 Porter un équipement de protection et respecter toutes

les instructions de sécurité. S’assurer que l’accessoire de

coupe s’immobilise lorsque le moteur tourne au ralenti.

Lorsque le moteur est arrêté, s’assurer que l’accessoire

de coupe est immobilisé avant de poser l’outil.

La page est en cours de chargement...

Homelite UT33650 Le manuel du propriétaire

Marque: Homelite

Modèle: UT33650

Catégorie: Coupe-herbe

Taper: Le manuel du propriétaire

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Homelite UT33650 Owner's manual
español: Homelite UT33650 El manual del propietario

Homelite UT33650 Le manuel du propriétaire

Ce manuel convient également à

Homelite UT33650 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents