US Stove Company US1269E Le manuel du propriétaire

Marque: US Stove Company

Modèle: US1269E

Catégorie: Poêle à bois

Taper: Le manuel du propriétaire

853614---3505i

U.S. Environmental Protection Agency

Certied to comply with 2020 particulate

emission standards for single burn rate

heaters. This single burn rate wood heater is

not approved for use with a ue damper.

United States Stove Company

227 Industrial Park Road

South Pittsburg, TN 37380

MODEL: US1269E Log Wood

CALIFORNIA PROPOSITION 65 WARNING:

This product can expose you to chemicals including carbon monoxide, which

is known to the State of California to cause cancer, birth defects and/or other

reproductive harm. For more information, go to www.P65warnings.ca.gov

Ce produit peut vous exposer à des agents chimiques, y compris au monoxyde de

carbone, lesquels sont reconnus dans l’État de la Californie comme causant le cancer et

des malformations congénitales ou autres dommages au fœtus. Pour obtenir plus de

renseignements, veuillez consulter le site www.P65warnings.ca.gov

SAFETY NOTICE:

If this heater is not properly installed, a house

re may result. For your safety, follow the

installation instructions. Never use make-shift

compromises during the installation of this

heater. Contact local building or re ofcials

about permits, restrictions and installation

requirements in your area.

CAUTION!

Please read this entire manual before you

install or use your new room heater. Failure

to follow instructions may result in property

damage, bodily injury, or even death.

Improper Installation Could Void Your

Warranty!

DO NOT USE THIS HEATER IN A MOBILE HOME.

SAVE THESE INSTRUCTIONS THIS MANUAL WILL

HELP YOU TO OBTAIN EFFICIENT, DEPENDABLE

SERVICE FROM THE HEATER, AND ENABLE YOU

TO ORDER REPAIR PARTS CORRECTLY. KEEP IN A

SAFE PLACE FOR FUTURE REFERENCE.

Certied to UL 1482-2011 (R2015)

and ULC-S627-00 (R2016)

Report Number: F19-526

-2-

Combustible: Wood

Colors: Flat Black

Flue Pipe Diameter: 6” (15.3 cm)

Flue Pipe Type: (Standard Single Wall): Black or Blued Steel 2100°F (650°C)

Minimum Chimney Height: 12’ (3.7 m)

Maximum Log Length: 19” (483 mm)

Electrical: None

Dimensions

Overall ( Depth x Width x Height ): 33” x 18.5” x 23” (838 mm X 470 mm X 854 mm)

Combustion Chamber: Width x Depth: 9” x 19” (229 mm X 482 mm)

Volume: Cubic Feet: 1.2 cubic feet

Door Opening: 7.5" x 10.2" (191 mm X 259 mm)

Weight (lbs): 140 lbs

The instructions pertaining to the installation of your wood stove comply with UL & ULC standards.

This manual describes the installation and operation of the United States Stove Company Model US1269E

woodheater. This heater meets the 2020 U.S. Environmental Protection Agency's crib wood emission limits for

woodheaters sold after May 15, 2020. Under specic EPA test conditions burning Douglas Fir dimensional lumber

this heater has been shown to deliver heat at a rate of 29,234 to 26,300 Btu/hr. This heater achieved a particulate

emissions rate of 1.8 g/hr when tested to method ASTM E2780-10 single Burn Rate Appendix (*and an efciency

of 67%.)

Note: Register your product on line at www.usstove.com. Save your receipt with your records for any claims.

NOTICE: This wood heater needs periodic inspection and repair for proper operation. It is against federal

regulations to operate this wood heater in a manner inconsistent with operating instructions in this manual. The

operation of this wood heater in a manner inconsistent with the owner’s manual will void you warranty.

-3-

READ THESE RULES AND THE INSTRUCTIONS CAREFULLY

1. Check with local codes. The installation must

comply with their rulings. Observe closely the

clearances to combustibles.

2. Do not install this heater in a mobile home or trailer.

3. Always connect this heater to a chimney and

vent to the outside. Never vent to another room or

inside a building. DO NOT CONNECT THIS UNIT TO A

CHIMNEY FLUE SERVING ANOTHER APPLIANCE.

4. Do not connect a wood burning heater to a Type

B gas vent. This is not safe and is prohibited by

the National Fire Protection Association Code.

This heater requires approved masonry or UL,

ULC Listed Residential Type and Building Heating

Appliance Chimney. Use a 6" diameter chimney,

or larger, that is high enough to give a good draft.

5. Be sure that your chimney is safely constructed and

in good repair. Have the chimney inspected by

the Fire Department or a qualied inspector. Your

insurance company may be able to recommend

a qualied inspector.

6. Inspect chimney connector and chimney twice

monthly during the heating season for any deposit

of creosote or soot which must be removed (see

the "Woodstove Utilization" section of this manual).

7. Provide air for combustion from outside the house

into the room where the heater is located. If the

intake is not in the same room, air must have free

access into the room.

8. To prevent injury, do not allow anyone to use this

heater who is unfamiliar with the correct operation

of the heater.

9. For further information on using your heater safely,

obtain a copy of the National Fire Protection

Association (NFPA) publication "Using Coal and

Wood Stoves Safely" NFPA No. HS-10-1978. The

address of the NFPA is Batterymarch Park, MA

02269.

• For more information on a Canadian Installation,

obtain a copy of CAN/CSA - B365 - M91 Installation

Code for Solid-Fuel-Burning Appliances and

Equipment.

10. CAUTION - The special paints used on your heater

may give off some smoke while they are curing

during the rst few res. Build small res at rst.

Children and people/animals with lung problems

should take caution during the curing process.

11. CARING FOR PAINTED PARTS - This heater has

a painted jacket which is durable but it will not

stand rough handling or abuse. When installing

your heater, use care in handling. Clean with soap

and warm water when heater is not hot. DO NOT

use any acids or scouring soap, as these wear and

dull the nish. PAINT DISCOLORATION WILL OCCUR

IF THE HEATER IS OVERFIRED. FOLLOW OPERATING

INSTRUCTIONS CAREFULLY.

12. All persons, especially children, should be alerted

to hazards from high surface temperatures and

kept away while in operation. Small children

should not be left unsupervised when in the room

with the heater.

13. Keep the area adjacent to the heater free from

all combustible materials, gasoline, and other

ammable vapors.

14. This heater should not be used as a primary source

of heat.

15. CAUTION DO NOT CONNECT TO OR USE IN

CONJUNCTION WITH ANY AIR DISTRIBUTION

DUCTWORK

Safety Rules

SAFETY NOTICE: If this heater is not properly installed, a house re may result. For your safety, follow the installation

directions. Contact local building or re ofcials about restrictions and installation inspection requirements in

your area.

CAUTION! Do not touch the heater until it has cooled.

NOTE: FOR YOUR SAFETY, WE RECOMMEND INSTALLING SMOKE DETECTORS IN YOUR HOME IF NOT ALREADY

INSTALLED.

-4-

Assembly Instructions

NOTICE: United States Stove Company grants no

warranty, stated or implied, for the installation or

maintenance of your wood stove and assumes no

responsibility of any incidental or consequential

damages.

REQUIRED TOOLS AND MATERIALS

Note: the following items are not included with your stove

• Safety Glasses

• Hearth Gloves

• Pencil

• 6' Folding Ruler

or Tape Measure

• Tin Snips

• Drill

• 1/8" dia. Drill Bit

• Adjustable

Wrench

• #2 philips screw

driver

• Chimney

Connector

• 1/2" Sheet Metal

Screws

• Chimney

• Furnace Cement

• Flooring

protector as

specied

CAUTION: Stove is heavy. Make sure you have

adequate help and use proper lifting techniques

whenever moving stove.

Description Qty

Hearth 1

Bottom Channel 1

Flue Collar 1

Legs 4

Handle Assembly 1

Door Assembly 1

Remove the following items located inside the rebox of this stove:

-5-

1. Uncrate the stove and remove packing materials

and protective poly bag (save cardboard box

for further assembly).

2. Remove parts from inside of the stove.

3. Place attened carton on the oor and carefully

turn stove over onto carton.

4. Attach the bottom air channel with four (4) 1/4-

20 X 3/8" screw, and four (4) washers.

5. Attach the hearth to the bottom of stove using

two (2) 1/4-20 x 1-3/16 screws, two (2) washers,

and two (2) 1/4-20 jam nuts.

6. Attach the front legs to the hearth with two

(2) 1/4-20 x 1-3/4 screws, two (2) washers, and

two (2) 1/4-20 jam nuts. NOTE: Only one leg is

equipped with a handle bracket. This bracketed

leg is designed to be installed at the front right

side of the unit.

7. Attach the rear legs to the base of the stove with

two (2) 1/4-20 x 1-3/4 screws, two (2) washers,

and two (2) 1/4-20 jam nuts.

8. Carefully lift the stove upright and place in the

desired location. Align the holes on the ue

collar to the holes on the stove and attach using

(2) two 1/4-20 X 1-3/4 screws.

9. Lower the feed door into position while aligning

hinge pins.

X 4

X 2

X 4

X 2

-6-

Installation

14”

356 mm

18”

458 mm

18”

458 mm

84” min.

2134 mm

CEILING

FLOOR PROTECTOR

BACK WALL

23”

585 mm

25-1/2”

648 mm

CEILING

FLOOR

PROTECTOR

SIDE WALL

16”

407 mm

16”

407 mm

FLOOR

PROTECTOR

MINIMUM CLEARANCE TO COMBUSTIBLE WALLS US, CANADA

Take into account the chimney’s location to insure it is not too close

to neighbors or in a valley which may cause unhealthy or nuisance

conditions. Heater/Floor Protector Location (Dimensions are required

for non-protected surfaces, see the chart for dimensions for protected

surfaces). Place the heater on solid masonry or solid concrete. When

the heater is used on a combustible oor, use an Underwriters Listed oor

protector. The oor protector must comply with UL Standards (USA) and

CAN/ULC (Canada) and have an R-value of 2.06. The oor protector

needs to extend at least 16" (Canada requires 18") beyond the door side

of the heater and 8" to each side. It should also extend 8" beyond the rear

for Canada. The oor protector needs to extend 2" beyond each side of

the ue pipe if it is elbowed towards a wall as well as 2" on each side of the

ue for horizontal runs.

1. After consulting the installation instructions for minimum clearances

to combustibles, locate the oor protector accordingly and carefully

place the stove in the selected location. Install stovepipe, elbows,

and thimble as necessary, utilizing either a recently cleaned and

inspected masonry chimney (properly lined) or a UL, ULC Listed

chimney. Ensure that the xed ue bafe that is provided is installed

in the ue collar. This bafe is intended to be in a xed location for

optimal combustion. Do not remove or alter the location of this bafe.

It is against federal regulations and will void the warranty.

2. Again, check the following illustrations and be sure to have the

clearances shown from the heater and the connector pipe to

combustible surfaces. If there is a solid brick or stone wall behind the

heater, please consult the local building code for specic regulations

that may apply in the area. However, if the wall is only faced with brick

or stone, consider it a combustible wall. To reduce ue clearances

from combustible materials, contact the local safety department.

3. If the chimney drafts excessively, purchase and use a Barometric

Draft Regulator (DR6 available from factory).

4. The chimney connection should be as short as possible, and the

heater must have its own ue. DO NOT CONNECT THIS UNIT TO A

CHIMNEY FLUE SERVING OTHER APPLIANCES.

5. Use three sheet metal screws in each stove pipe and or elbow joint to

rmly hold the pipe together. Seal around the screws

6. Do not install this heater in a mobile home or trailer.

7. Check local building and insurance codes. The installation must

comply with their rulings.

CAUTION! Keep furnishings and

other combustible materials

away from the heater.

8”

(204 mm)

8”

(204 mm)

US 16” (407 mm)

CAN 18” (458 mm)

(204 mm)

FLOOR

PROTECTOR

Non-combustible construction in accordance

with NFPA 211 (USA) or CAN/CSA B365-M91

(CANADA)

2”

(51 mm)

2”

(51 mm)

-7-

WRONG

RIGHT

FIG. 7

WRONG

FIG. 5

ELBOW

COLLAR

THIMBLE

FLOOR PROTECTOR

FLUE CONNECTION-NON-COMBUSTIBLE WALL

PIPE

NONCOMBUSTIBLE WALL

PIPE

BAROMETRIC

DRAFT REGULATOR

FIG. 6

PIPE REDUCER

FLOOR PROTECTOR

3 FT. MIN.

2 FT. MIN

10 FT.

CHIMNEY CAP MANDATORY

11 FT. MINIMUM

BAROMETRIC

DRAFT REGULATOR

PIPE

NONCOMBUSTIBLE

CONSTRUCTION IN

ACCORDANCE WITH

NFPA 211

Chimney Connection

MASONRY CHIMNEY

The masonry chimney must be code approved and have a ue liner.

The masonry chimney must comply with UL, ULC codes. Before using an

existing masonry chimney, clean the chimney and inspect the ue liner

to be sure it is safe to use. Make repairs before attaching the heater. The

connector pipe and ttings you will need to connect directly to a masonry

chimney are shown. If the connector pipe must go through a combustible

wall before entering the masonry chimney, consult a qualied mason or

chimney dealer. The installation must conform to local re codes, and

NFPA 211(USA) or CAN/CSA-B365-M91 (Canada). Do not connect this

heater into the same chimney ue as the replace or ue from another

heater. The chimney used for a heater must not be used to ventilate

the cellar or basement. If there is a cleanout opening at the base of the

chimney, close it tightly.

UL/ULC LISTED CHIMNEY

Carefully follow the chimney manufacturer's instructions. Use only listed

type HT per UL 103, ULC, 6-in diameter black or blued chimney connector,

minimum 24 gauge steel. If your chimney starts at the ceiling, you will need

enough 6" pipe to reach the ceiling. The top of the chimney must be at

least 3 feet above the roof and be at least 2 feet higher than any point of

the roof within 10 feet. Use double or triple wall pipe for the exterior portion

of the chimney.

RULES FOR CONNECTOR PIPE INSTALLATION

1. The crimped end of the pipe must be installed toward the heater.

The pipe should slide into the ue collar. The pipe should be rmly

attached to the ue collar with 3 screws and sealed with furnace

cement.

2. Slope any horizontal pipe upward toward the chimney at least 1/4" for

each foot of horizontal run. The horizontal section must be a minimum

of 24" from the stove.

3. You must have at least 18" inches clearance between any horizontal

piping and the ceiling.

4. The pipe cannot extend into the chimney ue.

5. Seal each connector pipe joint with furnace cement. Also, seal the

pipe at the chimney. Seal the inside with high-temperature silicone

and the outside with high-temperature tape.

6. Use 3 sheet metal screws at each joint to make the piping rigid.

7. It is recommended that no more than two (2) 90-degree bends be

used in the stove pipe installation as more than two (2) may decrease

the amount of draw and possibly cause smoke spillage.

NOTE: The chimney connector shall not pass through an attic, roof space,

oor, ceiling, or similar concealed space. Where passage through a wall

or partition of combustible construction is desired, the installation must

conform with CAN/CSA - B365.

IMPORTANCE OF PROPER DRAFT

Draft is the force which moves air from the appliance up through the

chimney. The amount of draft in your chimney depends on the length of

the chimney, local geography, nearby obstructions and other factors. Too

much draft may cause excessive temperatures in the appliance and may

damage the catalytic combustor (if equipped). Inadequate draft may

cause backpufng into the room and ‘plugging’ of the chimney or the

catalyst (if equipped). Inadequate draft will cause the appliance to leak

smoke into the room through appliance and chimney connector joints. An

uncontrollable burn or excessive temperature indicates excessive draft.

-8-

CONNECTION OF CHIMNEY CONNECTOR TO A MASONRY

CHIMNEY THROUGH A COMBUSTIBLE WALL

Figure 8 shows how to connect the chimney connector of a heater

to a masonry chimney through a combustible wall. There are ve

allowable ways that a chimney connector can be connected to

a masonry chimney by passing through a combustible wall. NFPA

Standard 211 allows the following wall pass-through systems.

1. Use a minimum 3-1/2" thick brick masonry wall framed into the

combustible wall. A reclay liner (ASTM C315 or equivalent)

having a 5/8" minimum wall thickness must be used and it

must be at least 12" away from any material that could catch

re. The inside diameter of the reclay liner shall be sized for

the proper snug t of a 6" diameter chimney connector pipe.

The reclay liner shall run from the outer surface of the brick

wall to, but not beyond, the inner surface of the chimney ue

and shall be rmly cemented in place (see Part A).

2. Use a solid insulated listed factory-built chimney length having

an inside diameter of 6" and 1" or more of solid insulation.

There must be at least a 9" air space between the outer wall

of the chimney length and any combustible materials. The

inner end of the chimney length shall be ush with the inside

of the masonry chimney, the ue shall be sealed to the ue

and to the brick masonry penetration with non-water-soluble

refractory cement. Sheet steel supports which are at least 24

gauge(0.024") in thickness shall be securely fastened to wall

surfaces on all sides. Fasteners between supports and the

chimney length shall not penetrate the chimney liner (see

Part B).

3. Use a 10" diameter ventilated thimble made of at least 24

gauge(0.024") steel having two 1" air channels. The ventilated

thimble must be separated from combustible materials

by a minimum of 6" glass ber insulation. The opening in

the combustible wall shall be covered and the thimble

supported with sheet steel supports which are at least 24

gauge (0.024") in thickness. The sheet steel supports shall be

securely fastened to wall surfaces on all sides and shall be

sized to t and hold the chimney section. Fasteners used to

secure chimney sections shall not penetrate chimney ue

liner (see Part C).

4. Use an 8" inside diameter solid insulated listed factory-built

chimney length which has 1" or more of solid insulation. The

minimum length of this chimney section shall be 12" and

will serve as a pass-through for the 6" diameter chimney

connector. There must be at least a 12" air space between

the outer wall of the chimney section and any combustible

materials. The chimney section shall be concentric with and

spaced 1" away from the chimney connector by means

of sheet steel support plates on both ends of the chimney

section. The opening in the combustible wall shall be covered

and the chimney section supported on both sides with sheet

steel supports which are at least 24 gauge (0.024") in thickness.

The sheet steel supports shall be securely fastened to wall

surfaces on all sides and shall be sized to t and hold the

chimney section. Fasteners used to secure chimney sections

shall not penetrate chimney ue liner (see Part C).

5. A listed factory-built wall pass-through system may be

purchased and installed according to the instructions pack

aged with it to provide a safe method of passing the chimney

connector through a combustible wall for connection to a

masonry chimney.

CONNECTION OF CHIMNEY CONNECTOR TO A MASONRY CHIMNEY THROUGH A COMBUSTIBLE WALL

Figure 8 shows how to connect the chimney connector of a heater to a masonry chimney through a combustible wall.

There are five allowable ways that a chimney connector can be connected to a masonry chimney by passing through

a combustible wall. NFPA Standard 211 allows the following wall pass-through systems.

MASONRY CHIMNEY

CONSTRUCTED TO

NFPA 211

AIRTIGHT

CLEANOUT

DOOR

FLOOR

PROTECTOR

COMBUSTIBLE WALL

HEATER

CHIMNEY CONNECTOR

CEILING

SEE PARTS A, B,

C, D, AND E OF

THIS FIGURE FOR

OPTIONS.

CHIMNEY FLUE

FIGURE 8 -

CONNECTION OF CHIMNEY CONNECTOR TO A

MASONRY CHIMNEY THROUGH A COMBUSTIBLE

WALL

(FIGURE 8 CONTINUED ON NEXT PAGE)

-9-

ADDITIONAL REQUIREMENTS PERTAINING TO FIGURE 8 AND THE ABOVE WALL PASS-THROUGH SYSTEMS

1. Insulation material used as part of wall pass-through system shall be of noncombustible material and shall

have a thermal conductivity of 1.0 Btu • in./ft.² • °F (4.88 kg • cal/hr • m² • °C) or less

2. All clearances and thicknesses are minimums: larger clearances and thickness are acceptable.

3. A chimney thimble, as shown for 3" and 4" above (Parts C and D respectively of Figure 8) shall be for types "3"

and 4" connections to facilitate removal of the chimney connector for cleaning. The chimney thimble shall

be of ASTM C315 reclay with 5/8" minimum wall thickness, or material of equivalent durability. The inside

diameter of the thimble shall be sized for the proper snug t of a 6" diameter chimney connector pipe. The

thimble shall be installed without damage to the chimney ue. The thimble shall extend through the chimney

wall to, but not beyond, the inner surface of the chimney ue and shall be permanently cemented in place

with high temperature cement.

4. A chimney connector to a masonry chimney, except for 2" above (Part B of Figure 8), shall extend through

the wall pass-through system to the inner face of the chimney ue, but not beyond. It does not have to be

fastened in place so long as it cannot accidently be pulled out of the chimney or shoved into the chimney

ue. If fasteners are used to secure the chimney connector to a masonry chimney, the fasteners shall not

penetrate the chimney ue liner.

5. Any material used to close up any opening for the connector shall be noncombustible.

PART E

In addition to the methods shown by A, B, C, and D of Figure 8, a listed factory-built wall pass-through system may

be purchased and installed according to the instructions packaged with it to provide a safe method of passing

chimney connector through a combustible wall for a connection to a masonry chimney.

CONNECTION OF CHIMNEY CONNECTOR TO A MASONRY CHIMNEY WHEN CHIMNEY CONNECTOR DOES NOT

PASS THROUGH A COMBUSTIBLE WALL

If the chimney connector does not have to pass through a combustible wall to get to a masonry chimney, simply

connect the chimney connector directly to the masonry chimney's chimney thimble as described and shown by

parts C and D. Remember, the chimney connector should extend into the chimney thimble to the inner face of

the chimney ue but not beyond; if the chimney connector is extended through the chimney thimble into the

chimney ue, resistance to the ow of smoke and gases up the chimney will occur; that ow resistance will have

an adverse affect on the operation and performance of the heater and venting system.

CAUTION! NEVER USE GASOLINE, GASOLINE-TYPE LANTERN FUEL, KEROSENE, CHARCOAL LIGHTER FLUID, OR

SIMILAR LIQUIDS TO START OR "FRESHEN UP" A FIRE IN THE HEATER. KEEP ALL SUCH LIQUIDS WELL AWAY FROM THE

HEATER WHILE IT IS IN USE.

WARNING! NEVER STORE FLAMMABLE LIQUIDS, ESPECIALLY GASOLINE. IN THE VICINITY OF THE HEATER.

CAUTION! OVERFIRING THE APPLIANCE MAY CAUSE A HOUSE FIRE. IF A UNIT OR CHIMNEY CONNECTOR GLOWS,

YOU ARE OVERFIRING.

WARNING! NEVER OPERATE THIS HEATER WITH THE FUEL DOOR OPEN.

WARNING! USE ONLY THE LEGS PROVIDED WITH THIS HEATER. REFER TO THE "INSTALLATION" SECTION OF THIS

MANUAL.

CAUTION HOT WHILE IN OPERATION. KEEP CHILDREN, CLOTHING AND FURNITURE AWAY. CONTACT MAY CAUSE

SKIN BURNS

CAUTION DO NOT BURN GARBAGE OR FLAMMABLE FLUIDS SUCH AS GASOLINE, NAPHTHA OR ENGINE OIL

CAUTION! USE WOOD OR WOOD-LIKE MATERIALS ONLY. DO NOT USE COAL OR CHARCOAL. COAL OR

CHARCOAL WILL DESTROY THE FIREBOX. DO NOT USE DRIED LUMBER OR TREATED WOOD.

NOTE: DO NOT ELEVATE FIRE OR USE WITH A GRATE, BUILD FIRE DIRECTLY ON THE HEARTH.

WARNING! DO NOT OBSTRUCT THE SPACE BENEATH THE HEATER

-10-

CAUTION: A chimney re may cause ignition of wall studs or rafters which you thought were a safe distance from

the chimney. If you have a chimney re, have your chimney inspected by a qualied person before using again.

SERVICE HINTS

Do not expect a heater to draw. It is the chimney that creates the draft. Smoke spillage into the house or excessive

buildup of water or creosote in the chimney are warnings that the chimney is not functioning properly. Correct

problem before using heater. Possible causes are:

1. The connector pipe may push into the chimney too far, stopping the draft.

2. Do not connect two heaters into the same chimney ue.

3. The chimney used for a heater must not be used to ventilate the cellar or basement. If there is a cleanout

opening at the base of the chimney, it must be closed tightly.

4. If the chimney is operating too cool, water will condense in the chimney and run back into the stove.

Creosote formation will be rapid and may block the chimney. Operate the heater at a high enough re to

keep the chimney warm preventing this condensation.

5. If the re burns well but sometimes smokes or burns slowly, it may be caused by the chimney top being lower

than another part of the house or a nearby tree. The wind blowing over a house or tree, falls on top of the

chimney like water over a dam, beating down the smoke. The top of the chimney should be at least 3 feet

above the roof and be at least to 2 feet higher than any point of the roof within 10 feet.

Woodstove Utilization

Your heating unit was designed to burn wood only; no other materials should be burned. Waste and other

ammable materials should not be burned in your stove. Higher efciencies and lower emissions generally result

when burning air dried seasoned hardwoods, as compared to softwoods or to green or freshly cut hardwoods.

Burning the following materials may result in release of toxic fumes or render the heater ineffective and cause

smoke.

DO NOT BURN:

1. Residential or commercial garbage;

2. Lawn clippings or yard waste;

3. Materials containing rubber, including tires;

4. Materials containing plastic;

5. Waste petroleum products, paints or paint thinners,

or asphalt products;

6. Materials containing asbestos;

7. Construction or demolition debris;

8. Paper products, cardboard, plywood, or

particleboard. The prohibition against burning

these materials does not prohibit the use of re

starters made from paper, cardboard, sawdust,

wax, and similar substances for the purpose of

starting a re in the unaffected wood heater.

9. Railroad ties or pressure-treated wood;

10. Manure or animal remains;

11. Saltwater driftwood or other previously salt water-

saturated materials;

12. Unseasoned wood;

13. Any materials that are not included in the warranty

and owner’s manual for the subject wood heater; or

14. Any materials that were not included in the

certication tests for the subject wood heater.

Do not burn manufactured logs made of wax impregnated sawdust or logs with any

chemical additives. Manufactured logs made of 100% compressed sawdust can be

burned, but be careful burning too much of these logs at the same time. Start with

one manufactured log and see how the stove reacts. You can increase the number

of logs burned at a time making sure the temperature never rises higher than 475 °F

(246 °C) on a magnetic thermometer for installation on single wall stove pipes or 900

°F (482 °C). The thermometer should be placed about 18” (457 mm) above the stove.

Higher temperatures can lead to overheat and damage your stove. Dead wood lying

on the forest oor should be considered wet and requires full seasoning time. Standing

deadwood can usually be considered to be about 2/3 seasoned. Splitting and stacking

wood before it is stored accelerates the drying time. Storing wood on an elevated surface from the ground and

under a cover or covered area from rain or snow also accelerates drying time. A good indicator if the wood is

ready to burn is to check the piece ends. If cracks are radiating in all directions from the center then the wood

should be dry enough to burn. If your wood sizzles in the re, even though the surface is dry, it may not be fully

cured and should be seasoned longer.

-11-

It is EXTREMELY IMPORTANT that you use DRY WOOD only in your wood stove. The wood should have dried for 9

to 15 months, such that the humidity content (in weight) is reduced below 20% of the weight of the log. It is very

important to keep in mind that even if the wood has been cut for one, two or even more years, it is not necessarily

dry if it has been stored in poor conditions. Under extreme conditions, it may rot, instead of drying. This point

cannot be overstressed; the vast majority of the problems related to the operation of a wood stove is caused by

the fact that the wood used was too damp or has dried in poor conditions. These problems can be:

– ignition problems

– creosote build-up causing chimney res

– low energy yield

– blackened windows

– incomplete log combustion

Smaller pieces of wood will dry faster. All logs exceeding 6” in diameter should be split. The wood should not be

stored directly on the ground. Air should circulate through the cord. A 24” to 48” air space should be left between

each row of logs, which should be placed in the sunniest location possible. The upper layer of wood should be

protected from the elements but not the sides.

TESTING THE WOOD

• When the stove is thoroughly warmed, place one piece of split wood (about ve inches in diameter) parallel

to the door on the bed of red embers.

• Keep the air control fully open by pulling on it and close the door. If the ignition of the piece is accomplished

within 90 seconds from the time it was placed inside the stove, the wood is correctly dried. If ignition takes

longer, the wood is damp.

• If the wood hisses and water or vapor escapes at the ends of the piece, the wood is soaked or freshly cut.

Do not use this wood in the stove. Large amounts of creosote could be deposited in the chimney, creating

potential conditions for a chimney re.

TAMPER WARNING

This wood heater has a manufacturer-set minimum low burn rate that must not be altered. It is against federal

regulations to alter this setting or otherwise operate this wood heater in a manner inconsistent with operating

instructions in this manual.

THE FIRST FIRES

The fresh paint on this stove needs to be cured to preserve its quality. Once the fuel charge is properly ignited,

only burn small res in the stove for the rst four hours of operation. Make sure that there’s enough air circulation

while curing the stove. The odors could be smelled during the 3 or 4 rst res. Never start your stove outside. A

person will not be able to see if the unit is overheating.

CAUTION: Never alter the damper slide or the adjustment range to increase ring for any reason. Doing so

could result in heater damage and will void your warranty.

TYPE

WEIGHT

(LBS. CU. FT., DRY)

PER CORD

EFFICIENCY

RANKING

SPLITS

M I L L I O N S

BTU’s/CORD

Hickory 63 4500 1.0 Well 31.5

White Oak 48 4100 .9 Fair 28.6

Red Oak 46 3900 .8 Fair 27.4

Beech 45 3800 .7 Hard 26.8

Sugar Maple 44 3700 .6 Fair 26.2

Black Oak 43 3700 .6 Fair 25.6

Ash 42 3600 .5 Well 25.0

Yellow Birch 40 3400 .4 Hard 23.8

Red Maple 38 3200 .3 Fair 22.6

Paper Birch 37 3100 .3 Easy 22.1

Elm/Sycamore 34 2900 .2 Very Difcult 20.1

Red Spruce 29 1800 .1 Easy 16.1

Any type of wood may be used in your stove, but specic varieties have better energy yields than others. Please

consult the following table in order to make the best possible choice.

-12-

VISIBLE SMOKE

Visible smoke is basically unburned fuel and moisture leaving your stove. The amount of visible smoke being

produced can be an effective method of determining how efciently the combustion process is taking place at

the given settings. Learn to adjust the air settings of your specic unit to produce the smallest amount of visible

smoke. Remember that wood that has not been seasoned properly and has a high wood moisture content will

produce excess visible smoke and burn poorly.

OPERATION OF THE HEATER

1. Burn wood or wood products only. The wood should be well seasons prior to use for maximum efciency.

2. Provide air into the room for combustion.

3. Do Not touch the heater after ring until it has cooled.

Do Not use a grate or elevate re, build re directly on the hearth. The fuel feed door must remain closed during

operation.

EFFICIENCY

Efciencies can be based on either the lower heating value (LHV) or the higher heating value (HHV) of the fuel.

The lower heating value is when water leaves the combustion process as a vapor, in the case of woodstoves the

moisture in the wood being burned leaves the stove as a vapor. The higher heating value is when water leaves

the combustion process completely condensed. In the case of woodstoves this would assume the exhaust gases

are room temperature when leaving the system, and therefore calculations using this heating value consider

the heat going up the chimney as lost energy. Therefore, efciency calculated using the lower heating value of

wood will be higher than efciency calculated using the higher heating value. In the United States all woodstove

efciencies should be calculated using the higher heating value.

As an operator of a wood heater the best way to achieve optimum efciencies is to learn the burn characteristic

of the appliance and burn well-seasoned wood. A good rule of thumb is that if the heater is not producing, or

producing very little visible smoke it is burning efciently. Also remember that higher burn rates are not always

the best heating burn rates; after a good re is established a lower burn rate may be a better option for efcient

heating. A lower burn rate slows the ow of usable heat out of the home through the chimney, and it also

consumes less wood.

BUILDING A FIRE

The top down method of re building is recommended for this appliance. Place the largest pieces of wood on

the bottom, laid in parallel and close together. Smaller pieces are placed in a second layer, crossways to the

rst. A third layer of still smaller pieces is laid crossways to the second, this time with some spaces between. Then

a fourth layer of loose, small kindling and twisted newspaper sheets tops off the pile.

OPERATIONAL TIPS FOR GOOD, EFFICIENT, AND CLEAN COMBUSTION

• Use smaller pieces of wood during start-up and a high burn rate to increase the stove temperature

• Be considerate of the environment and only burn dry wood

• Burn small, intense res instead of large, slow burning res when possible

• Learn your appliance's operating characteristics to obtain optimum performance

• Burning unseasoned wet wood only hurts your stoves efciency and leads to accelerated creosote buildup in

your chimney

RELOADING

Once a good bed of embers has been obtained, the unit should be reloaded. Open the door very slowly; open

it one or two inches for 5 to 10 seconds, before opening it completely to increase the draft and thus eliminate the

smoke which is stagnant in a state of slow combustion in the stove. Then bring the red embers to the front of the

stove and reload the unit. It is important to note that wood combustion consumes ambient oxygen in the room. In

the case of negative pressure, it is a good idea to allow fresh air in the room, either by opening a window slightly

or by installing a fresh air intake system on an outside wall.

WARNINGS:

• NEVER OVERFIRE YOUR STOVE. IF ANY PART OF THE STOVE STARTS TO GLOW RED, OVER FIRING IS HAPPENING.

• THE INSTALLATION OF A LOG CRADLE OR GRATES IS NOT RECOMMENDED IN YOUR WOOD STOVE BUILD FIRE

DIRECTLY ON HEARTH.

• ATTEMPTS TO ACHIEVE HEAT OUTPUT RATES THAT EXCEED HEATER DESIGN SPECIFICATIONS CAN RESULT IN

PERMANENT DAMAGE TO THE HEATER AND TO THE CATALYTIC COMBUSTOR IF SO EQUIPPED.

-13-

CREOSOTE - FORMATION AND NEED FOR REMOVAL

When wood is burned slowly, it produces tar and other organic vapors, which combine with expelled moisture

to form creosote. The creosote vapors condense in the relatively cool chimney ue of a slow-burning re. As a

result, creosote residue accumulates on the ue lining. When ignited, this creosote makes an extremely hot re.

The chimney connector and chimney should be inspected at least once every two months during the heating

season to determine if a creosote build-up has occurred. If creosote has accumulated (3mm or more), it should be

removed to reduce the risk of a chimney re. We strongly recommend that a magnetic thermometer be installed

on the smoke exhaust pipe, approximately 18” above the stove. This thermometer will indicate the temperature

of the gas exhaust fumes within the smoke exhaust system. The ideal temperature for these gases is somewhere

between 275°F and 500°F. Below these temperatures, the build-up of creosote is promoted. Above 500°, heat is

wasted since a too large quantity is lost into the atmosphere. Failure to remove creosote may cause a house re.

Creosote may be removed by using a chimney brush or other commonly available materials. Chimney res burn

very hot. If the chimney connector should glow red, immediately call the re department, then reduce the re by

blocking/closing the inlet air. Since this is a single burn rate heater a non- combustible material should be used

to block inlet air openings. If the re is burning vigorously, spray a multipurpose dry chemical extinguisher onto

the re in the stove if it can be done safely. Avoid introducing water into the chimney if possible as water could

damage the heated ue liner.

ASH REMOVAL AND DISPOSAL

Whenever ashes get 3 to 4 inches deep in the rebox or ash pan, and when the re has burned down and cooled,

remove excess ashes. Leave an ash bed approximately 1 inch deep on the rebox bottom to help maintain a hot

charcoal bed. Ashes should be placed in a metal container with a tight-tting lid. The closed container of ashes

should be placed on a noncombustible oor or on the ground, away from all combustible materials, pending

nal disposal. The ashes should be retained in the closed container until all cinders have thoroughly cooled.

SMOKE AND CO MONITORS

Burning wood naturally produces smoke and carbon monoxide(CO) emissions. CO is a poisonous gas when

exposed to elevated concentrations for extended periods of time. While the modern combustion systems in

heaters drastically reduce the amount of CO emitted out the chimney, exposure to the gases in closed or

conned areas can be dangerous. Also make sure you stove gaskets and chimney joints are in good working

order and sealing properly to ensure unintended exposure. It is recommended that you use both smoke and CO

monitors in areas expected to or having the potential to generate CO.

TO PREVENT CREOSOTE BUILD UP

• Always burn dry wood. This allows clean burns and higher chimney temperatures, therefore, less creosote

deposit.

• The secondary combustion can only take place if the rebox is hot enough.

• Always check for creosote deposit once every two months and have your chimney cleaned at least once a

year.

If a chimney or creosote re occurs, close all dampers (if applicable) immediately. Wait for the re to go out and

the heater to cool, then inspect the chimney for damage. If no damage results, perform a chimney cleaning to

ensure there is no more creosote deposits remaining in the chimney.

CAUTIONS: ASHES COULD CONTAIN HOT EMBERS EVEN AFTER TWO DAYS WITHOUT OPERATING THE STOVE.

-14-

Maintenance

Your wood stove is a high efciency stove and, therefore requires little maintenance. It is important to perform

a visual inspection of the stove every time it is emptied, in order to ensure that no parts have been damaged,

in which case repairs must be performed immediately. Inspect and clean the chimney and connector pipe

periodically for creosote buildup or obstructions.

GASKETING

This door uses a 3/8" rope gasket. It is recommended that you change the door gasket (which makes your stove

door air tight) once a year, in order to ensure good control over the combustion, maximum efciency, and

security. To change the door gasket, simply remove the damaged one. Carefully clean the available gasket

groove, apply a high temperature silicone sold for this purpose and install the new gasket. You may light up your

stove again approximately 24 hours after having completed this operation.

AIR TUBES

The air tubes assembled in this unit are designed to provide an accurate mix of secondary air to ensure the

highest efciency. Any damage or deterioration of these tubes may reduce the efciency of combustion. The

air tubes are held in position by either screws or snap pins. Locate these to either side of the tube and remove to

allow the tube to be removed and replaced.

SECONDARY AIR TUBES

The secondary air tubes must be cleaned with a wire brush. If debris remains in holes lightly tap with a wooden

stick to remove.

PAINT

Only clean your stove with a dry soft cloth that will not harm the paint nish. If the paint becomes scratched or

damaged, it is possible to give your wood stove a brand new look, by repainting it with a 1200° F heat resistant

paint. For this purpose, simply scrub the surface to be repainted with ne sand paper, clean it properly, and apply

thin coats (2) of paint successively.

WARNING:

NEVER OPERATE THE STOVE WITHOUT A GASKET OR WITH A BROKEN ONE. DAMAGE TO THE STOVE OR EVEN

HOUSE FIRE MAY RESULT.

-15-

Parts List

In order to maintain warranty, components must be replaced using original manufacturers parts purchased through your

dealer or directly from the appliance manufacturer. Use of third party components will void the warranty.

Key Part # Description Qty

1 40809 Flue Collar 1

2 40774 Main Top 1

3 88033 3/8" Rope Joint Top 1

4 88329 Bafe Board 1

5 893217 Tube Weldment 1

6 86961 1 Side Secondary Tube 1

7 86962 2 Side Secondary Tube 1

8 40299 Main Back 1

9 40892 Firebox Side 2

10 40897 Main Bottom 1

11 40817 Leg 4

12 89975 Handle Bracket 1

13 892722 Handle Assembly 1

14 892508 Bottom Channel 1

15 40771 Hearth 1

16 40896 Front 1

17 89971 Handle 1

18 40891 Cowl 1

19 40870 Feed Door 1

20 88033 3/8" Rope Gasket 1

21 88174 1/8 X 1 Window Gasket 1

22 892511 Door Panel Front 1

23 892843 Door Pin 2

-16-

Notes

It is recommended that your heating system is serviced regularly and that the appropriate Service Interval

Record is completed.

SERVICE PROVIDER

Before completing the appropriate Service Record below, please ensure you have carried out the service

as described in the manufacturer’s instructions. Always use the manufacturer's specied spare part when

replacement is necessary.

Service Record

Service 01 Date: _____________________

Engineer Name: ________________________________

License No.: ____________________________________

Company: _____________________________________

Telephone No.: _________________________________

Stove Inspected: Chimney Swept:

Items Replaced: ________________________________

Service 03 Date: _____________________

Engineer Name: ________________________________

License No.: ____________________________________

Company: _____________________________________

Telephone No.: _________________________________

Stove Inspected: Chimney Swept:

Items Replaced: ________________________________

Service 05 Date: _____________________

Engineer Name: ________________________________

License No.: ____________________________________

Company: _____________________________________

Telephone No.: _________________________________

Stove Inspected: Chimney Swept:

Items Replaced: ________________________________

Service 07 Date: _____________________

Engineer Name: ________________________________

License No.: ____________________________________

Company: _____________________________________

Telephone No.: _________________________________

Stove Inspected: Chimney Swept:

Items Replaced: ________________________________

Service 02 Date: _____________________

Engineer Name: ________________________________

License No.: ____________________________________

Company: _____________________________________

Telephone No.: _________________________________

Stove Inspected: Chimney Swept:

Items Replaced: ________________________________

Service 04 Date: _____________________

Engineer Name: ________________________________

License No.: ____________________________________

Company: _____________________________________

Telephone No.: _________________________________

Stove Inspected: Chimney Swept:

Items Replaced: ________________________________

Service 06 Date: _____________________

Engineer Name: ________________________________

License No.: ____________________________________

Company: _____________________________________

Telephone No.: _________________________________

Stove Inspected: Chimney Swept:

Items Replaced: ________________________________

Service 08 Date: _____________________

Engineer Name: ________________________________

License No.: ____________________________________

Company: _____________________________________

Telephone No.: _________________________________

Stove Inspected: Chimney Swept:

Items Replaced: ________________________________

UNITED STATES STOVE COMPANY

227 Industrial Park Road

P.O. Box 151

South Pittsburg, TN 37380

(423) 837-2100

www.USSTOVE.com

HOW TO ORDER REPAIR PARTS

THIS MANUAL WILL HELP TO OBTAIN EFFICIENT, DEPENDABLE SERVICE FROM THE HEATER, AND

WILL ENABLE THE CORRECT REPAIR PARTS TO BE ORDERED.

KEEP IN A SAFE PLACE FOR FUTURE REFERENCE.

WHEN WRITING, ALWAYS GIVE THE FULL MODEL NUMBER WHICH IS ON THE NAMEPLATE AT-

TACHED TO THE BACK OF THE HEATER.

WHEN ORDERING REPAIR PARTS, ALWAYS GIVE THE

FOLLOWING INFORMATION AS SHOWN IN THIS LIST /

CE GUIDE VOUS AIDERA À OBTENIR UN SERVICE EFFICACE ET FIABLE DE L’APPAREIL

DE CHAUFFAGE ET VOUS PERMETTRA DE COMMANDER CORRECTEMENT

DES PIÈCES DE RECHANGE.

VEUILLEZ CONSERVER CE GUIDE DANS UN ENDROIT SÛR À DES FINS DE RÉFÉRENCE.

LORSQUE VOUS NOUS ÉCRIVEZ, VEUILLEZ INDIQUER LE NUMÉRO COMPLET DU MODÈLE

QUI FIGURE SUR LA PLAQUE SIGNALÉTIQUE DE L’APPAREIL DE CHAUFFAGE.

LORSQUE VOUS COMMANDEZ DES PIÈCES DE RECHANGE, VEUILLEZ TOUJOURS FOURNIR LES

RENSEIGNEMENTS SUIVANTS, TELS QUE MONTRÉS DANS CETTE NOMENCLATURE:

1. The PART NUMBER / LE NUMÉRO DE PIÈCE _____________________________________

2. The PART DESCRIPTION / UNE DESCRIPTION DE LA PIÈCE ________________________

3. The MODEL NUMBER / LE NUMÉRO DE MODÈLE ________________________________

4. The SERIAL NUMBER / LE NUMÉRO DE SÉRIE ____________________________________

-18-

Il est recommandé que votre système de chauffage est desservi régulièrement et que le Service Interval

enregistrement approprié est terminée.

FOURNISSEUR DE SERVICES

Avant de terminer l’enregistrement de service approprié ci-dessous, s’il vous plaît vous assurer que vous avez

effectué le service tel que décrit dans le les instructions du fabricant. Toujours utiliser pièce de rechange indiquée

par le fabricant lors de remplacement est nécessaire.

Enregistrement De Service

Service de 01 Date: _____________________

Nom de l’ingénieur: ____________________________

N° de licence.: _________________________________

Compagnie: ___________________________________

N° de téléphone: _______________________________

Poêle Inspecté: Cheminée balayée:

Articles Remplacé: _____________________________

Service de 03 Date: _____________________

Nom de l’ingénieur: ____________________________

N° de licence.: _________________________________

Compagnie: ___________________________________

N° de téléphone: _______________________________

Poêle Inspecté: Cheminée balayée:

Articles Remplacé: _____________________________

Service de 05 Date: _____________________

Nom de l’ingénieur: ____________________________

N° de licence.: _________________________________

Compagnie: ___________________________________

N° de téléphone: _______________________________

Poêle Inspecté: Cheminée balayée:

Articles Remplacé: _____________________________

Service de 07 Date: _____________________

Nom de l’ingénieur: ____________________________

N° de licence.: _________________________________

Compagnie: ___________________________________

N° de téléphone: _______________________________

Poêle Inspecté: Cheminée balayée:

Articles Remplacé: _____________________________

Service de 02 Date: _____________________

Nom de l’ingénieur: ____________________________

N° de licence.: _________________________________

Compagnie: ___________________________________

N° de téléphone: _______________________________

Poêle Inspecté: Cheminée balayée:

Articles Remplacé: _____________________________

Service de 04 Date: _____________________

Nom de l’ingénieur: ____________________________

N° de licence.: _________________________________

Compagnie: ___________________________________

N° de téléphone: _______________________________

Poêle Inspecté: Cheminée balayée:

Articles Remplacé: _____________________________

Service de 06 Date: _____________________

Nom de l’ingénieur: ____________________________

N° de licence.: _________________________________

Compagnie: ___________________________________

N° de téléphone: _______________________________

Poêle Inspecté: Cheminée balayée:

Articles Remplacé: _____________________________

Service de 08 Date: _____________________

Nom de l’ingénieur: ____________________________

N° de licence.: _________________________________

Compagnie: ___________________________________

N° de téléphone: _______________________________

Poêle Inspecté: Cheminée balayée:

Articles Remplacé: _____________________________

-17-

Schéma Des Pièces

An de maintenir la garantie, les composants doivent être remplacés à l'aide des pièces originales du fabricant achetées via

votre revendeur ou directement auprès du fabricant de l'appareil. L'utilisation de composants tiers annulera la garantie.

Clé Partie # Description Qté

40809

collier de cheminée

40774

haut principal

88033

Joint de corde 3/8 "

88329

déecteur

893217

tube soudé

86961

Tube secondaire 1 côté

86962

Tube secondaire 2 côtés

40299

dos principal

40892

côté boîte à feu

40897

fond principal

40817

jambe

89975

support de poignée

892722

assemblage de la poignée

892508

canal du bas

40771

foyer

40896

cadre de porte

89971

manipuler

40891

capot

40870

porte d'alimentation

88033

Joint de corde 3/8

88174

Joint de fenêtre 1 / 8x1

892511

panneau de porte

892843 Goupille de porte 2

-16-

Entretien

Votre poêle à bois est à haute efcacité et ne requiert donc que très peu d’entretien. Il est important de faire une

inspection visuelle du poêle, chaque fois qu’il est vidé, an d’assurer qu’aucune pièce n’a été endommagée,

ce qui nécessiterait une réparation immédiate. Inspectez et nettoyez périodiquement la cheminée et le

raccordement du tuyau pour y déceler l’accumulation de créosote ou des obstructions.

ÉTANCHÉISATION

Cette porte utilise un joint de corde de 3/8 po. Il est recommandé de changer le joint de la porte (assurant

l’étanchéité à votre porte) une fois par année, an de vous assurer un bon contrôle sur la combustion, une

efcacité maximale et la sécurité. Pour changer le joint de la porte, retirez simplement celui qui est endommagé.

Nettoyez ensuite avec soin la rainure du joint, appliquez un silicone à haute température vendu à cette n et

installez le nouveau joint. Vous pourrez allumer votre poêle à nouveau dans environ 24 heures après avoir terminé

cette opération.

CONDUITS D’AIR SECONDAIRES

Les conduits d’air secondaires doivent être nettoyés avec une brosse métallique. Si des débris demeurent dans

les trous, frappez légèrement avec un bâton de bois pour les déloger.

CONDUITS D’AIR

Les conduits d’air assemblés dans cette unité sont conçus pour offrir un mélange précis d’air secondaire et

assurer une plus grande efcacité. Tout dommage ou détérioration de ces conduits peuvent réduire l’efcacité

de la combustion. Les conduits d’air sont maintenus en position par des vis ou par des goupilles de blocage.

Localisez et enlevez-les des deux côtés du conduit pour le retirer et le remettre en place.

PEINTURE

Nettoyez uniquement votre poêle avec un chiffon doux qui n’endommagera pas le ni. Si la peinture devient

égratignée ou endommagée, il est possible de redonner une apparence neuve à votre poêle en le repeignant

avec une peinture résistant à une chaleur de 649 °C (1200 °F). À cette n, frottez la surface à être repeinte avec

un papier à poncer n, nettoyez et appliquez successivement 2 nes couches de peinture.

AVERTISSEMENT :

NE JAMAIS FAIRE FONCTIONNER LE POÊLE SANS UN JOINT D’ÉTANCHÉITÉ OU AVEC UN JOINT BRISÉ. CECI

POURRAIT CAUSER DES DOMMAGES AU POÊLE OU MÊME CAUSER UN INCENDIE.

La page charge ...

US Stove Company US1269E Le manuel du propriétaire

Marque: US Stove Company

Modèle: US1269E

Catégorie: Poêle à bois

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: US Stove Company US1269E Owner's manual

US Stove Company US1269E Le manuel du propriétaire

US Stove Company US1269E Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents