Marvel 4FWWL Mode d'emploi
- Catégorie
- Réfrigérateurs-congélateurs
- Taper
- Mode d'emploi
Refrigerator / Freezer
Réfrigérateur / Congélateurs
ML24RFP0**
ML24RFS0**
ML24RFP4**
ML24RFS3**
ML24RIP5**
ML24RIS4**
EN Installation, Operation and Maintenance Instructions
FR Instructions d’installation, d’utilisation et d’entretien
2
NOTE
!
CAUTION
Important Safety Instructions
Warnings and safety instructions appearing in this guide
are not meant to cover all possible conditions and situa-
tions that may occur. Common sense, caution, and care
must be exercised when installing, maintaining, or operat-
ing this appliance.
Recognize Safety Symbols,
Words, and Labels.
CAUTION-Hazards or unsafe practices which could re-
sult in personal injury or property / product damage.
NOTE-Important information to help assure a problem
free installation and operation.
CONTENTS
Contents:
Safety information ...............................................................2
Unpacking your appliance ..................................................3
Warranty registration .....................................................3
Installing your appliance ......................................................4
Cabinet clearances .........................................................4
Leveling the appliance ....................................................4
Electrical connection ......................................................5
Installing the water supply ...................................................6
Ice-maker operation .............................................................7
Product dimensions ...........................................................8
Starting your appliance ..................................................10
Using your Electronic control ............................................10
Sleep mode ...................................................................10
Turning your appliance "ON" or "OFF" ..........................11
Adjusting the temperature .............................................11
Temperature mode ........................................................11
Control lock ....................................................................11
Temperature sensor error codes ...................................12
Alarms ...........................................................................12
Door ajar ..................................................................12
Power failure .............................................................13
Temperature alarm ....................................................13
Vacation mode ..................................................................13
Overlay door panel installation ........................................14
Shelf removal ...................................................................19
Energy saving tips ............................................................19
Care and cleaning .............................................................20
Obtaining service .............................................................20
Troubleshooting refrigerator freezer and ice-maker ..........21
Troubleshooting ice-maker ..............................................22
Warranty ...........................................................................23
!
WARNING
WARNING - You can be killed or seriously injured
if you do not follow these instructions.
!
WARNING
State of California Proposition 65 Warning:
This product contains one or more chemicals known
to the State of California to cause cancer.
!
WARNING
State of California Proposition 65 Warning:
This product contains one or more chemicals known
to the State of California to cause birth defects or
other reproductive harm..
3
NOTE
!
CAUTION
XXXXXXXXXXXX
XXXXXXXXXXXX
!
WARNING
WARNING - Help Prevent Tragedies
the past. Junked or abandoned refrigerators are still
dangerous - even if they sit out for "just a few hours".
If you are getting rid of your old refrigerator, please
follow the instructions below to help prevent acci-
dents.
Before you throw away your old refrigerator or
freezer:
•
• Leave the shelves in place so children may not
easily climb inside.
!
WARNING
WARNING - Dispose of the plastic bags which can
MARVEL
!
WARNING
EXCESSIVE WEIGHT HAZARD
Use two or more people to move product.
Failure to do so can result in personal injury.
Remove Interior Packaging
Your appliance has been packed for shipment with all parts
that could be damaged by movement securely fastened.
Remove internal packing materials and any tape holding in-
ternal components in place. The owners manual is shipped
inside the product in a plastic bag along with the warranty
registration card, and other accessory items.
Important
Keep your carton and packaging until your appliance has
been thoroughly inspected and found to be in good condi-
tion. If there is damage, the packaging will be needed as
proof of damage in transit. Afterwards please dispose of all
items responsibly.
Note to Customer
This merchandise was carefully packed and thoroughly
inspected before leaving our plant. Responsibility for its
safe delivery was assumed by the retailer upon acceptance
of the shipment. Claims for loss or damage sustained in
transit must be made to the retailer.
DO NOT RETURN DAMAGED MERCHANDISE TO THE
MANUFACTURER - FILE THE CLAIM WITH THE
RETAILER.
If the appliance was shipped, handled, or stored in other
than an upright position for any period of time, allow the ap-
pliance to sit upright for a period of at least 24 hours before
plugging in. This will assure oil returns to the compressor.
Plugging the appliance in immediately may cause damage
to internal parts.
Warranty Registration
UNPACKING YOUR APPLIANCE
Online registra-
tion available at
www.marvelrefrig-
eration.com
It is important you send in your warranty registration card
immediately after taking delivery of your appliance or you
can register online at www.marvelrefrigeration.com.
The following information will
be required when registering
your appliance.
Service Number
Serial Number
Date of Purchase
Dealer’s name and address
The service number and serial number can be found on the
serial plate which is located inside the cabinet on the right
Figure 1
4
!
CAUTION
!
WARNING
INSTALLING YOUR APPLIANCE
Select Location
The proper location will ensure peak performance of your
appliance. We recommend a location where the unit will
be out of direct sunlight and away from heat sources. To
-
mended installation location temperature range is from 55
Cabinet Clearance
Ventilation is required from the bottom front of the appli-
ance. Keep this area open and clear of any obstructions.
Adjacent cabinets and counter top can be installed around
the appliance as long as the front grille remains unob-
structed. Overlay door models with articulated hinges are
intended for built-in applications only.
An optional stacking kit is required to stack products.
Failure to use a stacking kit could result in personal
injury. Contact your dealer or Marvel customer service
at 800-223-3900 to order.
Front Grille
Do not obstruct the front grille. The openings within the
-
energy usage and loss of cooling capacity. For this reason
it is important this area not be obstructed and the grille
openings kept clean. Marvel does not recommend the use
Leveling Legs
Adjustable legs at the front and rear corners of the appli-
-
all height of your Marvel appliance may be adjusted higher
To adjust the leveling legs, place the appliance on a solid
lean the appliance back to access the front leveling legs.
Raise or lower the legs to the required dimension by turning
the legs. Repeat this process for the rear by tilting the appli-
ance forward using caution. On a level surface check the
appliance for levelness and adjust accordingly.
The front grille screws may be loosened and the grille ad-
justed to the desired height. When adjustment is complete
Rear
Leveling
Legs
Figure 2
Front Leveling
Legs
Front Grille,
keep this area
open.
Model Door Style
Minimum
Height
Maximum
Height
ML24 S
33
3
4"
34
3
4"
ML24 P
34"
35"
Table A
5
NOTE
Figure 3
Figure 4
Do not remove
ground prong
INSTALLING YOUR APPLIANCE
Front grille
Front grille screw
Figure 5
Electrical Shock Hazard
• Do not use an extension cord with this appliance.
They can be hazardous and can degrade product
performance.
• This appliance should not, under any circumstanc-
es, be installed to an un-grounded electrical supply.
• Do not remove the grounding prong from the power
•
• Do not splash or spray water from a hose on the
appliance. Doing so may cause an electrical shock,
which may result in severe injury or death.
!
WARNING
Electrical Connection
A grounded 115 volt, 15 amp dedicated circuit is required.
This product is factory equipped with a power supply
cord that has a three-pronged, grounded plug. It must be
plugged into a mating grounding type receptacle in accor-
dance with the National Electrical Code and applicable lo-
not have a grounding type receptacle, it is the responsibility
and obligation of the customer to provide the proper power
supply. The third ground prong should not, under any cir-
cumstances, be cut or removed.
Figure 6
-
sance tripping which will cause the appliance to shut down.
GFCI’s are generally not used on circuits with power equip-
ment that must run unattended for long periods of time, un-
less required to meet local building codes and ordinances.
6
• -
tings.
• Reverse osmosis, softened water, and de-ionized water
quality of the ice.
Water
Supply
Line
Clamp and
Screw
Water valve
inlet
Figure 7
Back view of
ice machine
NOTE
NOTE
!
CAUTION
Water line from water valve
to ice-maker
INSTALLING THE WATER SUPPLY
MODEL ML24RI AND MODEL ML24RF WITH OPTIONAL ICE-MAKER KIT
Compression
Water
supply
line
Water supply
service loop
If you have model ML24RI you have a factory installed ice-
maker.
-
able for model ML24RF which includes all of the necessary
parts for installation. The kit can be obtained from Marvel
customer service by calling 800-223-3900.
Water valve
inlet
Water Supply
Observe and follow all local building codes when installing
this appliance.
Use
¹
" outside diameter copper tubing for your water sup-
ply which is available at any local hardware or plumbing
supply store. Bend the
¹
" copper tubing to suit your instal-
lation being sure not to kink the tubing. Purchase enough
copper tubing length and coil it behind the unit to form a
"service loop" which will allow the appliance to be pulled
out from the installation for servicing or cleaning. Connect
the copper tubing to the "top side" of a cold water pipe to
prevent the ice-maker from plugging with sediment.
ease servicing the appliance. NOTE: A SELF-PIERCING
TYPE VALVE IS NOT RECOMMENDED as they are prone
to clogging with sediment which will create pressure drop
reducing the water supply to the unit.
Connect the copper tubing water supply to the water valve
supply line to the back of the cabinet with the screw and
clamp provided in the corner of the back panel. (See Figure
Water pressure must be at a minimum of 20 psi for proper
operation and a maximum of 120 psi.
Make certain all water connections are watertight after in-
stallation. Form the tubing so that it will not vibrate against
the cabinet body or kink when your appliance is set in posi-
tion.
7
NOTE
Ice-maker operation
• The unit must be installed level for proper ice-maker
operation.
• -
• When the freezer section and ice-maker unit has suf-
automatically.
• When the ice bucket is full, the ice-maker will automati-
• You may manually stop the ice-maker by raising the
-
Arm down, ice-maker
will operate
Arm up, stops operation
Figure 8
When operation of the appliance is to be discontinued
for any length of time, the ice cube mold in the ice-maker
should be emptied by allowing the ice-maker to dispense
1.
2. Raise the ice-maker bail arm.
3. Empty the ice bucket.
4. Replace the ice bucket in the unit and lower the bail
arm.
Dispensing of the cubes should occur within 2 hours. After
the ice-cubes dispense - empty, clean, and replace the ice
cube bucket, and raise the bail arm.
ICE-MAKER OPERATION
!
CAUTION
The water supply to the ice-maker must be turned on prior
to turning the ice-maker on. Failure to do so will cause
rapid dry cycling of the ice-maker mold heater resulting in
temperature control issues in the freezer compartment.
-
ing the bucket, or ice may be dispensed onto the freezer
If the ice is not used regularly, it will clump together with
time. For best ice results, discard ice in the bin as required
and allow the ice-maker to make a new fresh batch of ice.
removing the bucket.
Long and short term storage of ice-maker:
8
"A"
"B"
"C"
"D"
"E"
PRODUCT DIMENSIONS
MODEL
ROUGH-IN OPENING DIMENSIONS CABINET DIMENSIONS
"A" "B" "C" "D" "E" "F" "G" "H" "J"
ML24R*S
24"
**34" to 35"
24"
23
7
8"
33
3
4" to 34
3
4"
23
23
32"
25
21
32"
46
13
32"
25
11
16"
ML24R*P
24"
**34
1
4" to 35
1
4"
* 24"
23
7
8"
34" to 35"
22
7
8"
-
46
1
2"
23
1
8"
DOOR STYLE
Figure 9
Figure 9a
Figure 10
If necessary to gain clearance inside the rough-in
opening a hole can be cut through the adjacent cabi-
net and the power cord routed through this hole to a
power outlet. Another way to increase the available
opening depth is to recess the power outlet into the
rear wall to gain the thickness of the power cord plug.
Not all recessed outlet boxes will work for this applica-
tion as they are too narrow, but a recessed outlet box
equivalent to Arlington #DVFR1W is recommended for
9
"F"
"D"
"E"
"H"
"J"
"G"
Water
inlet
Water
inlet
4
7
8"
1
1
4"
PRODUCT DIMENSIONS
MODEL
PRODUCT DATA
ELECTRICAL
REQUIREMENTS #
PRODUCT
WEIGHT
ML24R*S 115V/60Hz/15A
140 lbs
ML24R*P 115V/60Hz/15A
140 lbs
-
cent cabinetry doors, custom decorative panel thickness
cannot exceed
3
4
** Minimum rough-in opening required is to be larger than
the adjusted height of the cabinet.
# A grounded 15 amp dedicated circuit is required. Follow
all local building codes when installing electrical and appli-
ance.
Figure 11
21
1
2"
10
Power Failure
ALARM RESET
Compartment
select
REF
FRZ
The sleep mode can be disabled if you prefer to have the
display on continuously. Press and hold the "Lock" key-
pad until the display goes past "Loc" and reads "nSL". To
enable the sleep mode, repeat the instruction, again going
past "Loc" until the display reads "SLP".
sound, and the current storage compartment temperature
will be displayed.
Sleep mode:
If no keypads are pressed for 60 seconds, the display will
enter sleep mode to conserve power. The control panel will
go dark with the exception of the system status "OK" indi-
cator which will remain enabled. Alarm conditions will wake
To make the following changes to the control settings
(turning the appliance ON/OFF, adjusting the tempera-
ture, and activating vacation mode), the control must
be awake.
Starting your appliance:
Plug the appliance power cord into a 115 volt wall outlet.
Your appliance is shipped from the factory in the "On" posi-
tion and will begin start-up of cooling as soon as power is
wall outlet has power, and that the control is in the "On"
On initial power up, the control display will indicate a
"Power Failure" alarm. This is a normal condition as the ap-
pliance was powered-up at the factory for quality inspection
and then removed from power. A momentary press of the
STARTING YOUR APPLIANCE
Figure 12
Electronic control
Temp
Minus
keypad
Temp
Plus
keypad
On/O
keypad
Display Area
Lock
keypad
System Status
indicators
NOTE
Your product has an automatic defrost feature that utilizes
an electric heater element. Periodically during defrost you
may observe the following:
• Water dripping and running sounds as a result of the
frost melt.
• Sizzling and popping sounds from water dripping on
the heater element.
• A faint reddish glow in the freezer compartment from
the electric heater element.
These are all “normal” operating characteristics related to
refrigeration product incorporating automatic defrost. They
do not represent any product fault or safety issue.
Using your electronic control:
11
NOTE
warmer respectively. When you have reached your desired
or do nothing and the "Set" mode will time-out in 10-sec-
onds accepting the displayed temperature as the new
set-point.
The available set-point temperature range for your appli-
-
the refrigerator compartment. If you attempt to adjust the
temperature outside of these ranges you will receive an
Freezer
compartment
selected
Refrigerator
compartment
selected
REF
FRZ
REF
FRZ
Temperatures can be set for each individual compartment
select the compartment you want to set the temperature for.
will be illuminated for the respective display.
To change the set temperature for a particular compart-
ment, with the compartment enabled and out of sleep
mode, press the "-" or "+" keypads. "SET" will be indi-
cated on the user interface panel and the current set-point
the "-" or "+" keypads will adjust the temperature colder or
Adjusting the temperature:
When initially loading your product with warm contents, it
may take up to 48-hours for the storage compartment tem-
perature to stabilize.
When making temperature set-point changes, it may take
up to 24-hours for the stored contents to stabilize at your
new set-point temperature.
temperature:
• Changes to temperature setting.
• Room temperature changes.
• Temperature of stored contents.
- Loading warm contents.
- Cold content load will delay the change to a warmer
set-point temperature.
- Warm content load will delay the change to a colder
set-point temperature.
•
• Use of the storage compartment display lighting, (glass
• Installation of the appliance in direct sunlight or next to
a heat source.
Turning your appliance ON and OFF:
-
perature will be shown in the display area of the control.
keypad for 4-seconds. "OFF" will now be displayed on the
control.
keypad for 4-seconds.
USING YOUR ELECTRONIC CONTROL
Temperature mode:
The temperature mode is preset from the factory in Fahren-
while pressing the "+" keypad, then release the "-" keypad.
Repeat the procedure to change the temperature mode
Control lock:
The control panel can be locked to avoid unintentional
changes. To lock the control, press and hold the "Lock" key-
pad until the display reads "Loc" then immediately release
and then continuously illuminate. When the control panel is
locked, only the Lock keypad, System Status OK indicator
, and the Alarm indicator are active. To un-lock the control
panel, repeat this instruction until the display reads "nLc"
NOTE
control will have to be unlocked before using the key-
pad to reset an alarm condition. See page 11 (Control
12
Temperature Sensor Error Codes
Sensor Displayed Code Error Description Action to Take
Refrigerator
Temperature
Sensor
Failed temperature sensor in the
refrigerator compartment. Can lead to
unwanted storage temperatures and/or
spoiled perishable goods.
Call service to have the
temperature sensor replaced and
remove all perishable goods from com-
partment to prevent spoilage.
Freezer
Temperature
Sensor
Failed temperature sensor in the
freezer compartment. Can lead to
unwanted storage temperatures and/or
spoiled perishable goods.
Call service to have the
temperature sensor replaced and
remove all perishable goods from com-
partment to prevent spoilage.
Defrost Sensor
Failed defrost temperature sensor.
Causes unit to not defrost properly and
can create large frost build-up. Can lead
to water damage to the unit and sur-
Unplug the power cord
immediately and call service to have
the defrost sensor replaced.
Door Ajar
ALARM RESET
This alarm condition can be reset by closing the door
alarm will recur in 5-minutes if the alarm condition
persists.
USING YOUR ELECTRONIC CONTROL
Alarms:
The control will alert you to conditions that could adversely
• Door ajar - If the door is open, or not closed prop-
erly, for more than 5-minutes the System Status OK
and a tone will sound every 60 seconds. Additionally,
an "ALARM RESET" indicator will be displayed below
The temperature sensors are monitored continuously. Any
OPEN or SHORTED circuit condition will initiate an
ERROR CODE as listed below:
Temperature Sensor Error Codes
NOTE
The audible alarm can be muted, for each occurrence,
by pressing the lock keypad.
13
ALARM RESET
Power Failure
ALARM RESET
Temp
NOTE
Door Ajar
Temp
This alarm condition can be reset by momentarily pressing
that you check the condition of your stored contents, even
though the appliance is operating normally and the temper-
ature has recovered, as prolonged temperature excursions
could spoil perishables.
• Power failure - If power to the appliance is inter-
"ALARM RESET" indicator will be displayed below the
condition can be reset by momentarily pressing the
-
ed that you check the condition of any perishables,
even if the appliance is operating normally and the tem-
perature has recovered, as prolonged power outages
could result in excessive temperature excursions which
may spoil perishables.
• Temperature alarm - If the storage compart-
ment temperature deviates excessively from your
set-point temperature for an extended period of time,
will sound every 60 seconds. Additionally, an "ALARM
RESET" indicator will be displayed below the "ON/
OFF" keypad.
Multiple alarms are possible, i.e.- "Door Ajar" for a pro-
longed period may trigger a "Temp" alarm, in which case
both "Door Ajar" and "Temp" indicators will activate.
Vacation mode:
This operating mode can be used to save energy during
high cost energy periods, or when you won't be using your
appliance for an extended period of time by disabling the
lights, alarm tones, and keypad entry tones. Vacation mode
also serves as a Sabbath mode, disabling functions and
its controls in accordance with the weekly Sabbath and
religious holidays observed within the Orthodox Jewish
community. When used as Sabbath mode, you may open
or close the door at any time to access contents without
-
outs, solenoids, fans, valves, compressor, icons, tones, or
alarms.
When activated, the display, alarm indicators and tones,
keypad touch tones, interior lights, and all options are dis-
abled. All keypad functions are disabled, with the exception
-
mode. Storage compartment temperatures are monitored
and controlled at the settings prior to entering Vacation
mode.
To enter Vacation Mode (with the control out of sleep
"VAC" 3-times to acknowledge your request, then will
display "VAC" continuously until Vacation mode is exited.
A power outage will not exit Vacation mode, exiting can
only be accomplished manually. To exit Vacation mode and
keypad until the control displays the temperature.
USING YOUR ELECTRONIC CONTROL
NOTE
The audible alarm can be muted, for each occurrence, by
pressing the lock keypad.
NOTE
NOTE
After a high temperature alarm condition, check all perish-
ables to ensure they are safe for consumption.
The temperature alarm may occur as a result of high usage
or introduction of warm contents to the storage compart-
ment. If the temperature alarm continues to occur, your unit
may require service.
14
!
CAUTION
!
WARNING
!
WARNING
Use extreme caution with the articulated hinges. The
hinge is self closing and many pinch points exist prior
to built-in installation. Do not remove the cabinet "Z"
bracket from the top of the cabinet.
!
WARNING
The articulated hinges have many pinch points. Care-
fully close / collapse the hinges as soon as the door is
removed from the cabinet.
2 phillips head screws on the
top and bottom hinges
Figure 13a
Cabinet
"Z" Bracket
Figure 13
"P" clamp
and screw
Wire connector
see Figure 14
Figure 13b
Bottom of
door
OVERLAY DOOR PANEL INSTALLATION
If you purchased an overlay panel model, your unit is
equipped with articulated hinges to allow fully integrated
built-in installations. Custom panel thicknesses of
5
8" (15
3
4
It is important to use the factory provided grille that came
through the condenser. The use of a custom grille is not
recommended and will void the warranty.
Overlay panel models are designed for use with built-
in installations only. Use in freestanding installations
could result in personal injury.
Step 1: Removing the Door
With a phillips screwdriver remove the screw and "P" clamp
from the bottom of the door near the hinge. See Figure 13b.
Disconnect the door wire harness by pressing and holding
down the locking tab on the wire connector and pulling the
connector apart. See Figure 14.
Open the door and loosen the screws holding the hinges to
remove the screws but loosen them enough so the hinges
the side.
With a helper, and being careful not to scratch the cabinet
or the door, slide the door to the side about
1
2 inch and
remove the hinges and door from the unit.
15
!
CAUTION
Weight of overlay door panel must not exceed 15
pounds (6.8 kg).
Press and hold down this
tab on the wire connector
and pull the connector apart.
OVERLAY DOOR PANEL INSTALLATION
Step 2: Remove the door gasket
corner of the door remove the magnetic door gasket from
the interior side of the door, see Figure 15. Set the gasket
There are 10 holes in the gasket retainer extrusions, (3 on
each side and 2 at the top and bottom which are used to
fasten the panel to the front of the door. The screws are
provided in the literature pack.
Figure 14
Overlay panel to
be centered on
width of door.
Overlay panel
and side of
door.
Magnetic Gasket
remove starting at a
corner, grasp and pull
away from the door.
Holes in
gasket
retainer.
Figure 15a
Figure 15
Step 3: Cut and drill the overlay panel
Depending on your model cut the overlay door panel to the
dimensions shown in Figures 16 to 19.
16
!
CAUTION
Weight of overlay door panel must not
exceed 15 pounds (6.8 kg).
1
5
32"
1
5
32"
OVERLAY DOOR PANEL INSTALLATION
Clearance for
screw head,
4 places
Hinge side of door
Clearance
for hinge
at top and
bottom
Figure 18
Left Hand Hinged Door
24" (61 cm) wide appliance
Figure 19
Left Hand Hinged Door
24" (61 cm) wide appliance
Top of door
1
3
4"
1
4"
Deep
x
1
4
6 places
2"
3
11
16"
1
1
2"
typical
1
11
16"
30
11
32"
1
4
radius is
permissible
14"
1
3
16"
3
1
8"
Clearance
for hinge
at top and
bottom
Top of door
Clearance for
screw head,
4 places
Figure 16
Right Hand Hinged Door
24" (61 cm) wide appliance
Hinge side of door
23
3
4"
23
3
4"
Figure 17
Right Hand Hinged Door
24" (61 cm) wide appliance
3
1
8"
1
3
4"
2"
3
11
16"
1
4"
Deep
30
11
32"
x
1
4
4 places
1
1
2"
typical
1
11
16"
4
7
8"
4
7
8"
14"
1
3
16"
1
4
radius is
permissible
This side
facing interior
This side
facing interior
17
OVERLAY DOOR PANEL INSTALLATION
Material Type #10 Wood Screw
Hardwood
¹
Softwood
Table B
Figure 20
#10 x 1/2"
screw
Step 4: Assemble the panel to the door
The preferred method of attaching the panel to the door
is to clamp the panel to the door so it cannot move while
drilling the screw pilot holes. Use bar clamps or "C" clamps
with pads on the clamping surfaces that will not mar the
panel or the door. The custom overlay panel should be
of the door. See Figure 15a. Drill holes through the gasket
extrusion using the 10 holes as pilot holes. Use the drill
size from the chart in Table "B", being careful not to drill
through the front surface of the panel. If the overlay panel is
thinner than
5
8
obtained. Fasten the panel to the door with the 10 screws
the clamps and replace the gasket in the gasket extrusion
channels of the door. Some force may be required to seat
the gasket into the channels. Be sure the gasket corners
are seated properly.
Step 6: Secure the cabinet
Use the #8 x
3
4" black screws from the literature pack to
secure the counter top to the cabinet top through the holes
in the cabinet "Z" bracket.
Step 5: Install the door
Carefully open the top and bottom hinges on the door being
careful as there are many pinch points. Place the hinges
over the 4 screws in the cabinet, 2 at the top and 2 at the
bottom and slide the door into position. Tighten the 4 hinge
screws with a phillips screwdriver. (See Figures 13 and
bottom of the door with the screw and "P" clamp removed
Figure 21
Cabinet
"Z" bracket
#8 x
3
4" black
screws
18
SHELVING CONFIGURATIONS
Refrigerator / Freezer
24" (61 cm) wide see Figure 22:
Refrigerator:
see Figure 25
Freezer:
Refrigerator / Freezer
24" (61 cm) wide see Figure 24:
Refrigerator:
see Figure 25
Freezer:
Refrigerator / Ice-maker
24" (61 cm) wide see Figure 23:
Refrigerator:
Freezer:
Figure 22
Figure 25
Figure 26
Ice Bucket
RI model only
Figure 27
Freezer shelf
RF model only
Ice-maker
and bucket
Figure 23
Figure 24
Freezer
compartment
19
SHELVING CONFIGURATIONS AND ENERGY SAVING TIPS
To remove the crisper :
Pull out until it stops. Lift up on the front of the pan, and
remove it from the frame.
To Add or Remove a Shelf
Remove stored product from the shelf. Do not try to remove
a loaded shelf from the appliance. Grasp the shelf front with
both hands, rotate the front upward and lift out. (See Figure
insert the top hooks into the shelf support slots and drop
the shelf down so the hooks drop over the bottom of the
slots.
Make sure your cantilever shelf is secure on the shelf sup-
ports by pressing down on the shelf before loading.
!
CAUTION
Grasp the shelf
by the front with both
hands and rotate the front
of the shelf up, then lift the
shelf up and remove the
shelf from the shelf
ladders.
!
CAUTION
Never try to move a loaded shelf, remove everything from
the shelf before moving. Use both hands when moving the
shelf.
Figure 29
Figure 28
The following suggestions will minimize the
cost of operating your refrigeration appliance.
1. Do not install your appliance next to a hot appliance
heat sources.
2. Install product out of direct sunlight.
3. Ensure the front grille vents at front of appliance be-
neath door are not obstructed and kept clean to allow
ventilation for the refrigeration system to expel heat.
4. Plug your appliance into a dedicated power circuit. (Not
5. When initially loading your new product, or whenever
large quantities of warm contents are placed within
refrigerated storage compartment, minimize door
openings for the next 12 hours to allow contents to pull
down to compartment set temperature.
6. Maintaining a relatively full storage compartment will
require less appliance run time than an empty compart-
ment.
7. Ensure door closing is not obstructed by contents
stored in your appliance.
8. Allow hot items to reach room temperature before plac-
ing in product.
9. Minimize door openings and duration of door openings.
10. Use the warmest temperature control set temperature
that meets your personal preference and provides the
proper storage for your stored contents.
11. When on vacation or away from home for extended pe-
riods, set the appliance to warmest acceptable tem-
perature for the stored contents and raise the ice-maker
bail arm to stop ice production.
appliance requires the door to be open for an extended
period of time.
20
!
CAUTION
CARE AND CLEANING AND OBTAINING SERVICE
Front Grille
-
ings in front of the cabinet. At least once or twice a year,
brush or vacuum lint and dirt from the front grille area (see
SHOCK HAZARD: Disconnect electrical power from the
appliance before cleaning with soap and water.
Cabinet
The painted cabinet can be washed with either a mild soap
and water and thoroughly rinsed with clear water. NEVER
use abrasive scouring cleaners.
Interior
Wash interior compartment with mild soap and water. Do
NOT use an abrasive cleaner, solvent, polish cleaner or
undiluted detergent.
Care of Appliance
1. Avoid leaning on the door, you may bend the door
hinges or tip the appliance.
2. Exercise caution when sweeping, vacuuming or mop-
ping near the front of the appliance. Damage to the
grille can occur.
3. Periodically clean the interior of the appliance as
needed.
4. Periodically check and/or clean the front grille as
needed.
In the Event of a Power Failure
If a power failure occurs, try to correct it as soon as pos-
sible. Minimize the number of door openings while the
temperature.
Light assembly replacement
All models use LED lamps to illuminate the interior of the
appliance. This component is very reliable, but should one
of the LED.
If Service is Required:
•
please contact your dealer or call Marvel Customer
Service at 800.223.3900 for directions on how to obtain
warranty coverage in your area.
•
Marvel Customer Service can provide recommenda-
tions of service centers in your area. A listing of autho-
rized service centers is also available at www.marvelre-
frigeration.com under the service and support section.
• In all correspondence regarding service, be sure to
give the service number, serial number, and proof of
purchase.
• Try to have information or description of nature of the
problem, how long the appliance has been running, the
room temperature, and any additional information that
may be helpful in quickly solving the problem.
• Table "C" is provided for recording pertinent information
regarding your product for future reference.
For Your Records
Date of Purchase
Dealer’s name
Dealer’s Address
Dealer’s City
Dealer’s State
Dealer’s Zip Code
Appliance Serial Number
Appliance Service Number
Date Warranty Card Sent (Must
Table C
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
Marvel 4FWWL Mode d'emploi
- Catégorie
- Réfrigérateurs-congélateurs
- Taper
- Mode d'emploi
dans d''autres langues
- English: Marvel 4FWWL User guide
Documents connexes
-
Marvel MP24FAP4RP Mode d'emploi
-
-
-
-
-
Marvel MO24RFS2LS Manuel utilisateur
-
-
-
-