Simplicity ELECTRIC PRESSURE WASHER, BRIGGS & STRATTON POWERFLOW+ [email protected] MODEL 020602-00 Manuel utilisateur
- Catégorie
- Outils de jardin
- Taper
- Manuel utilisateur
Ce manuel convient également à
Not for
Reproduction
This pressure washer is rated in accordance to the Pressure Washer
Manufacturers Association (PWMA) standard PW101-2010 (Testing and
Rating Performance of Pressure Washers).
BRIGGS & STRATTON CORPORATION
MILWAUKEE, WISCONSIN, U.S.A.
Manual No. 80012465 Revision C
Electric Pressure Washer
OPERATOR’S MANUAL
POWERflow+ TECHNOLOGY™
Not for
Reproduction
2 BRIGGSandSTRATTON.COM
Thank you for purchasing this quality-built Briggs & Stratton® electric pressure washer. We are pleased that you’ve
placed your confidence in the Briggs & Stratton brand. When operated and maintained according to the instructions in this
manual, your Briggs & Stratton electric pressure washer will provide many years of dependable service.
This manual contains safety information to make you aware of the hazards and risks associated with electric pressure
washers and how to avoid them. Because Briggs & Stratton does not necessarily know all the applications this electric
pressure washer could be used for, it is important that you read and understand these instructions thoroughly before
attempting to start or operate this equipment. Save these original instructions for future reference.
This electric pressure washer requires final assembly before use. Refer to the Assembly section of this manual for
instructions on final assembly procedures. Follow the instructions completely.
Where to Find Us
You never have to look far to find Briggs & Stratton support and service for your electric pressure washer. Consult
your Yellow Pages. There are over 30,000 Briggs & Stratton authorized service dealers worldwide who provide quality
service. You can also contact Briggs & Stratton Customer Service by phone at (800) 743-4115, or on the Internet at
BRIGGSandSTRATTON.COM.
Electric Pressure Washer
Model Number _____________________________
Revision __________________________________
Serial Number ______________________________
Date Purchased ___________________________
Copyright © 2017. Briggs & Stratton Corporation
Milwaukee, WI, USA. All rights reserved.
Table of Contents
Operator Safety.............................. 3
Assembly................................... 6
Features and Controls ........................ 8
Operation................................... 9
Maintenance ...............................12
Storage ...................................13
Troubleshooting ............................14
Warranty ..................................15
Specifications ..............................16
Not for
Reproduction
3
Operator Safety
SAVE THESE INSTRUCTIONS
Equipment Description
Every effort has been made to ensure that the information
in this manual is accurate and current. However, we
reserve the right to change, alter, or otherwise improve the
product and this document at any time without prior notice.
This ISM device complies with Canadian ICES-001.
POWERflow+ Technology
POWERflow+ Technology is a deep cleaning pressure
washer with both high pressure to lift dirt AND high flow to
easily wash it away. In the high flow mode, POWERflow+
Technology enhances the cleaning experience by
providing extended reach, power soaping, and faster
rinsing capabilities.
The force behind POWERflow+ is in the pump with two
separate cleaning modes: high pressure and high flow.
The high-pressure mode delivers up to 1800 PSI (pounds
square inch) and is ideal for cleaning the toughest stains,
mildew and grime from decks, driveways and siding, while
the high-flow mode delivers up to 4 GPM (gallons per
minute) to power-rinse away dirt, soap and debris. The
high flow mode also makes it the best to use for washing
delicate surfaces such as patio furniture, vehicles, and
children’s outdoor play sets and toys.
Briggs & Stratton’s POWERflow+ Technology is a system
of components working in concert to deliver the high-flow
capability. Water is sent from the pump to the specially
designed 26 ft. hose and into the custom-engineered
POWERflow+ gun with soft grip handle. Water then flows
into the exclusive 7-in-1 nozzle that allows user to change
from High Pressure to High Flow, without changing nozzle
tips, and propels the stream up to 30 ft.
Ground Fault Circuit Interrupter Protection
This pressure washer is provided with a ground-fault
circuit-interrupter (GFCI) built into the plug of the power
supply cord. This device provides additional protection
from the risk of electric shock. Should replacement of
the plug or cord become necessary, use only identical
replacement parts that include GFCI protection.
Automatic Shut-Off
The electric pressure washer is equipped with a sensor
that will detect that water flow has stopped when releasing
or locking the spray gun trigger. The sensor will cause the
motor to shut off for as long as the spray gun trigger is
released or locked.
If motor continues to run when spray gun trigger is released
or locked, DO NOT USE THE MACHINE. Call the electric
pressure washer helpline at (800) 743-4115 for assistance.
NOTICE The electric pressure washer is equipped with a
main power ON/OFF switch. The switch should always be
moved to the OFF position (0) when the electric pressure
washer is not being used to prevent possible damage.
Motor Overload
The electric motor in this electric pressure washer is
equipped with an overload protection device (thermostat).
This device will automatically shut off the motor if the motor
overheats or draws excessive current.
If the overload protection device is tripped, disconnect the
power supply by turning the master ON/OFF switch to the
OFF (0) position. Let unit cool for 30 minutes. Then turn
the master ON/OFF switch to the ON (I) position to resume
operation.
Important Safety Information
Please read and understand this entire manual before
attempting to assemble, operate or service the product.
Follow the maintenance instructions specified in this
manual. If you have any questions regarding the product,
please call customer service at (800) 743-4115, 8 a.m. -
5 p.m., CST, Monday - Friday.
Safety Symbols and Meanings
The safety alert symbol indicates a potential personal
injury hazard. A signal word (DANGER, WARNING, or
CAUTION) is used with the alert symbol to designate a
degree or level of hazard seriousness. A safety symbol
may be used to represent the type of hazard. The signal
word NOTICE is used to address practices not related to
personal injury.
DANGER indicates a hazard which, if not avoided, will
result in death or serious injury.
WARNING indicates a hazard which, if not avoided,
could result in death or serious injury.
CAUTION indicates a hazard which, if not avoided,
could result in minor or moderate injury.
NOTICE address practices not related to personal injury.
WARNING Failure to read and follow the operator’s
manual and all operating instructions before
using could result in death or serious injury.
• Read this manual carefully and become familiar with
your electric pressure washer. Know its applications, its
limitations, and any hazards involved.
Chemical Burn
Electrical Shock
Slippery Surface Fall
Flying Objects
Read Manual
Projectile
Fluid Injection
Fire
Not for
Reproduction
4 BRIGGSandSTRATTON.COM
WARNING Use of electric pressure washer could
create puddles and slippery surfaces.
Risk of kickback. Spray gun could
kickback causing you to fall resulting in
death or serious injury.
• Operate the electric pressure washer from a
stable surface.
• Do not overreach or stand on unstable support. Keep
good footing and balance at all times.
• The cleaning area should have adequate slopes
and drainage to reduce the possibility of a fall due to
slippery surfaces.
• Be extremely careful if you must use the electric
pressure washer from a ladder, scaffolding, or any
other similar location.
• Firmly grasp spray gun with both hands when using
power spray modes to avoid injury when spray gun
kicks back.
WARNING The high pressure stream of water that
this equipment produces could cut through skin
and its underlying tissues, resulting in serious
injury and possible amputation.
Spray gun traps high water pressure, even when motor
is stopped and water is disconnected, which could result
in serious injury.
• NEVER aim spray gun at people, animals, or plants.
• ALWAYS point spray gun in safe direction, squeeze
spray gun trigger to release high pressure, every time
you turn off pressure washer.
WARNING Risk of eye or bodily injury. Spray could
splash back, propel objects or cause
internal harm resulting in serious injury.
• Always wear indirect vented (chemical splash) safety
goggles marked to comply with ANSI Z87.1 when using
or in vicinity of this equipment. NEVER substitute safety
glasses or dry-condition goggles for indirect vented
safety goggles.
• Know how to stop the pressure washer and bleed
pressure quickly. Be thoroughly familiar with the
controls.
• DO NOT allow CHILDREN to operate the electric
pressure washer.
• Keep operating area clear of all persons.
• Inspect high pressure hose before each use. NEVER
repair high pressure hose; replace it.
• DO NOT repair leaking connections with sealant of any
kind; replace o-rings and gaskets.
• Keep hose connected to electric pressure washer and
spray gun while system is pressurized.
• ALWAYS point spray gun in safe direction while system
is pressurized and squeeze spray gun trigger to release
high pressure, every time you turn off the pressure
washer.
• DO NOT aim spray gun at people or animals.
• DO NOT
drink from hose connected accessories.
• DO NOT secure spray gun in open position.
• DO NOT leave spray gun unattended while the electric
pressure washer is in ON (I) position.
• DO NOT use a spray gun which does not have a trigger
lock or trigger guard in place and in working order.
• Always be certain spray gun and accessories are
correctly attached.
• Stay alert – watch what you are doing.
• DO NOT operate the product when fatigued or under
the influence of alcohol or drugs.
• Close supervision is necessary when this product is
used near children.
WARNING Risk of electrocution. Contacting both
power conductors, at the same time could
cause electric shock or burn resulting in death
or serious injury.
• Inspect cord before each use, DO NOT use if cord is
damaged.
• The product is equipped with a ground fault circuit
interrupter (GFCI) built into the power cord plug. If
replacement of the plug or cord is required, use only
identical replacement parts.
• Keep all connections dry and off the ground.
• DO NOT touch plug with wet hands.
• DO NOT run cord through doorways, windows, holes in
ceilings, walls, or floors.
• DO NOT walk on cord.
• DO NOT drive over, drag or place objects over cord.
• DO NOT spray near power source.
WARNING Risk of electrocution. Use of an
extension cord could cause electric shock or
burn resulting in death or serious injury.
• DO NOT use an extension cord with this electric
pressure washer. Your home’s electrical circuit
receptacle or extension cord may not provide lifesaving
ground-fault circuit-interruption protection.
For Servicing of a Double-Insulated Appliance, See
Assembly Section.
Not for
Reproduction
5
WARNING Risk of fire. Spraying flammable liquids
could result in death or serious injury.
• DO NOT spray flammable liquids.
WARNING Risk of fire. Overheated cord could result
in death or serious injury.
• Uncoil cord completely prior to use.
• DO NOT cover cord with any material.
WARNING This product contains lead and lead
compounds, known to the State of California to cause
birth defects or other reproductive harm. Wash your
hands after handling this product.
NOTICE High pressure spray could damage fragile
items including glass.
• DO NOT point spray gun at glass when using 0° nozzle
setting.
• NEVER aim spray gun at plants.
NOTICE You must protect your unit from freezing
temperatures.
• Failure to do so will permanently damage your pump
and render your unit inoperable.
• Freeze damage is not covered under warranty.
NOTICE Improper treatment of electric pressure washer
could damage it and shorten its life.
• If you have questions about intended use, ask dealer or
contact authorized service center.
• DO NOT operate units with broken or missing parts, or
without protective housing or covers.
• DO NOT by-pass any safety device on the electric
pressure washer.
• DO NOT modify the electric pressure washer in any
way.
• DO NOT move the electric pressure washer by pulling
on hoses. Move unit using the transport handle
supplied.
• Use ONLY branded accessories intended for use with
this product.
WARNING Chemical Burn Hazard.
Chemicals could cause burns resulting
in death or serious injury.
• Always wear indirect vented (chemical splash) safety
goggles marked to comply with ANSI Z87.1 when using
chemicals.
• DO NOT substitute safety glasses or dry-condition
goggles for indirect vented safety goggles.
• DO NOT use caustic liquid with electric pressure
washer.
• Use ONLY pressure washer safe detergents/soaps.
Follow all manufacturers instructions.
Not for
Reproduction
6 BRIGGSandSTRATTON.COM
Assembly
Read entire operator’s manual before you
attempt to assemble or operate your new
electric pressure washer.
Your electric pressure washer requires some assembly
but is quickly ready for use. If you have any problems with
the assembly of your electric pressure washer, please call
the electric pressure washer helpline at (800) 743-4115. If
calling for assistance, please have the model, revision, and
serial number from the identification label available.
Tools Needed
• Philips screwdriver #2
Unpack Electric Pressure Washer
1. Remove everything from carton.
2. Ensure you have all included items prior to assembly.
Items Included in the Carton
• Main unit
• Handle with accessory tray
• Spray gun
• High pressure hose
• Nozzle extension
• 7-in-1 nozzle
• Handle support tubes (2)
• Parts bag (which includes the following):
• Red high pressure nozzle
• Water inlet coupling
• Screws (2)
• Handle bolts (2)
• Plastic knobs (2)
• O-ring kit
• Nozzle cleaning tool
• Operator’s manual
• Owner’s registration card
Check all contents. If any parts are missing or damaged, call
the electric pressure washer helpline at (800) 743-4115.
Become familiar with each component before assembling
the electric pressure washer. Identify contents with the
illustration shown in Features and Controls.
Prior to Operation
• Please fill out and send in the registration card.
• Read and perform the following instructions while
paying close attention to all warnings and notices.
NOTICE For best performance, connect ONLY to water
source capable of supplying greater than 5 GPM (18.9 l)
and
25-75 psi (1.72-5.17 bar)
at the electric pressure
washer end of garden hose. Inspect all equipment, hoses
and accessories thoroughly before each use, DO NOT
use if damaged.
• ONLY use branded accessories intended for use with this
product.
• For optimum performance, DO NOT use a garden hose
that exceeds 50 feet in length.
• Replace only with original equipment parts. To order, call
(800) 743-4115 or visit BRIGGSandSTRATTON.COM.
Attach Handle Support Tubes and Handle
1. Slide handle support tubes (A) into slots on back of
main unit. Align and attach handle support tubes with
a screw (B) on each side. Maintain alignment while
tightening with a #2 philips screwdriver.
2. Place handle (C) onto handle support tubes
connected to main unit. Make sure holes in handle
align with holes on handle support tubes.
3. Insert handle bolts (D) through holes from inside of
unit and attach a plastic knob (E) from outside of unit.
Tighten by hand.
Lubricate O-Rings
Lubrication of o-rings is extremely important for installation
and operation. The use of a lubricant (petroleum or
synthetic grease) during assembly helps seat o-rings
properly and provides an improved seal. It also helps
protect the o-ring from damage by abrasion, pinching or
cutting and extends the life of the o-ring.
NOTICE ALWAYS apply a small amount of lubricant on
o-rings prior to assembling the garden hose to the pump
(A), high pressure hose (B), nozzle extension (C) and
spray gun (D).
C
D
E
A
B
B
A
C
B
D
A
Not for
Reproduction
7
Lubricate all connections shown below, following these
instructions:
1. Inspect and clean connecting surfaces prior to
lubrication and assembly.
2. Use lubricants sparingly during assembly; a light film
is all that is required.
3. Use a small brush or cotton swab to apply grease
directly to o-rings where they are not accessible (QC
fitting, M22 fitting).
Connect Hoses and Water Supply
NOTICE Use ONLY cold water (less than 100°F).
1. Uncoil high pressure hose and attach black end of
hose to base of spray gun. Tighten by hand.
2. Attach blue end of high pressure hose to high
pressure outlet on pump. Tighten by hand.
3. Attach garden hose (50 ft. / 15.24 m maximum) to
water supply and run water through garden hose for
30 seconds to flush the hose of debris. Turn off water.
4. Confirm that water inlet screen (A) and black rubber
washer (B) is installed in water inlet coupling (C).
5. Attach water inlet coupling (C) to right side (viewing
from rear) of main unit as shown. Tighten by hand.
NOTICE DO NOT run pump without water supply
connected and turned on.
• Damage to equipment resulting from failure to follow
this instruction will void warranty.
6. Attach garden hose (D) to water inlet coupling (C).
Tighten by hand.
Connect Nozzle Extension and 7-in-1
Nozzle
1. Turn ON water, point gun in a safe direction, press
trigger lock button (D), then squeeze trigger to purge
pump system and spray gun of air and impurities.
2. Attach nozzle extension to spray gun. Tighten by
hand.
3. Pull back on collar of nozzle extension, insert 7-in-1
nozzle and release collar. Tug on 7-in-1 nozzle to
make sure it is securely in place. See How to Use
Nozzles.
Servicing Of A Double-Insulated
Appliance
In a double-insulated product, two systems of insulation
are provided instead of grounding. No grounding means
is provided on a double-insulated product, nor should a
means for grounding be added to the product. Servicing
a double-insulated product requires extreme care and
knowledge of the system, and should be done only by
qualified service personnel. Replacement parts for a
double-insulated product must be identical to the parts
they replace. A double-insulated product is marked
with the words “DOUBLE INSULATION” or “DOUBLE
INSULATED.”
The symbol means DOUBLE-INSULATED
APPLIANCE.
D
A
B
D
C
Not for
Reproduction
8 BRIGGSandSTRATTON.COM
Features and Controls
Read the Operator’s Manual and safety rules before operating your electric pressure washer.
Compare the illustrations with your electric pressure washer to familiarize yourself with the locations of various
controls and adjustments. Save this original manual for future reference.
A - Spray Gun — Controls the application of water onto
cleaning surface with trigger device. Includes trigger lock.
B - 7-in-1 Nozzle — Contains seven different spray
pattern nozzles for various applications.
C - Accessory Tray — Provides convenient storage for
standard and optional accessories.
D - Nozzle Extension with Quick Connect — Allows you
to switch between 7-in-1 nozzle and optional accessories.
E - Detergent Tank — Use to hold up to 40 fl. oz. (1.2 l) of
pressure washer safe detergent.
F - High Pressure Outlet — Connection for high pressure
hose.
G - Master ON/OFF Toggle Switch — Push top of switch
in to turn pressure washer ON (I). Push bottom of switch in
to turn pressure washer OFF (0).
H - Electric Cord with GFCI — The electric pressure
washer and operator is protected by a ground fault circuit
interrupter (GFCI).
J - Identification Label — Provides model and serial
number of pressure washer. Please have these readily
available if calling for assistance.
K - Water Supply Inlet — Connect to water supply using
a 50 ft. (15.24 m) maximum garden hose.
L - High Pressure Hose — Connect one end to high
pressure water outlet and the other end to spray gun.
M - Warning Label — Identifies hazards to be avoided
when using your pressure washer.
A
E
H
K
B
C
D
G
J
F
L
M
Not for
Reproduction
9
Operation
How to Start Your Electric Pressure
Washer
Follow the instructions below in the order presented. If
you have any problems operating your electric pressure
washer, please call the electric pressure washer helpline at
(800) 743-4115.
WARNING Risk of eye injury. Spray could splash
back or propel objects resulting in serious
injury. Always wear indirect vented (chemical
splash) safety goggles marked to comply with
ANSI Z87.1 when using or in vicinity of this equipment.
NEVER substitute safety glasses or dry-condition
goggles for indirect vented safety goggles.
1. Place the electric pressure washer near an outside water
source capable of supplying water at a flow rate greater
than 5 gallons per minute (18.9 l) and 25-75 psi (1.72-
5.17 bar) at the electric pressure washer end of garden
hose. DO NOT siphon supply water.
2. Connect garden hose to water inlet.
3. Check that high pressure hose is tightly connected
to spray gun and high pressure outlet. See Assembly
section.
NOTICE If hose connections start leaking during use,
shut down unit as described in steps 1-4 of How to Stop
Your Electric Pressure Washer. Remove hose completely
and reinstall hand tight. Failure to completely remove
hose could damage o-ring and cause hose connection to
continue leaking. If o-ring becomes damaged, replace with
provided o-rings. The blue o-ring goes to the blue end of
the high pressure hose and the black o-ring goes to the
black end of the high pressure hose.
NOTICE DO NOT run the pump without the water supply
connected and turned on.
• Damage to equipment resulting from failure to follow
this instruction will void warranty.
4. Turn ON water, point gun in a safe direction, press
trigger lock button and squeeze trigger to purge pump
system of air.
5. Install nozzle extension and 7-in-1 nozzle onto spray
gun. See Assembly section.
6. Press master ON/OFF switch (A) to OFF (0) position.
WARNING Risk of electrocution. Use of an
extension cord could cause electric shock or
burn resulting in death or serious injury.
• DO NOT use an extension cord with this electric
pressure washer. Your home’s electrical circuit
receptacle or extension cord may not provide lifesaving
ground-fault circuit-interruption protection.
7. Plug electrical power cord into a dedicated electrical
circuit rated for 120 Volts AC at 15 Amps that is
properly installed in accordance with all local codes and
ordinances. Circuit is not to supply any other electrical
needs. The indicator light on the GFCI should be ON.
NOTICE The indicator light must be ON for the electric
pressure washer to operate.
WARNING Risk of electrocution. Non-operating
ground fault circuit interrupter (GFCI) could
result in death or bodily injury. If indicator light
does not stay ON after test and reset, do not
use GFCI.
8. Press TEST button (B). The indicator light (C) should
be OFF.
9. Press RESET button (D). The indicator light (C)
should be ON.
NOTICE DO NOT use the electric pressure washer if
above test fails.
10. Press master ON/OFF switch to ON (I) position.
11. Point gun in a safe direction, press trigger lock button
and squeeze trigger.
The electric pressure washer motor will start and stop as
spray gun trigger is depressed and released.
The electric pressure washer is now ready for use.
Instructions for use of the supplied accessories are given
later in this section.
NOTICE DO NOT run pressure washer for more than 1
hour in a 2 hour period.
B
D
C
A
Not for
Reproduction
10 BRIGGSandSTRATTON.COM
How to Stop Your Electric Pressure
Washer
The electric pressure washer motor runs only when the
trigger is engaged. To stop the electric pressure washer
and turn off the motor:
1. Release spray gun trigger.
2. Press master ON/OFF switch to OFF (0) position.
NOTICE Releasing the trigger will shut off the motor but
does not shut off electrical power to the unit.
3. Turn off water supply.
4. ALWAYS point spray gun in a safe direction, press
trigger lock button and squeeze trigger to relieve built
up pressure in the unit.
WARNING The high pressure stream of water that
this equipment produces could cut through skin
and its underlying tissues, resulting in serious
injury and possible amputation.
Spray gun traps high water pressure, even when motor
is stopped and water is disconnected, which could result
in serious injury.
• Keep high pressure hose connected to pump and
spray gun while system is pressurized.
• ALWAYS point spray gun in safe direction, squeeze
spray gun trigger to release high pressure, every time
you turn off pressure washer.
5. Disconnect GFCI plug from outlet and coil power cord
on bottom hook of accessory tray.
6. Wrap high pressure hose and store on top hook of
accessory tray.
7. Store red high pressure nozzle on end of nozzle
extension. Store spray gun, nozzle extension and 7-in-
1 nozzle on the accessory tray.
How to Use Nozzles
7-in-1 Nozzle
The 7-in-1 nozzle allows you to switch between seven
different spray pattern nozzles. Release trigger on spray
gun to engage safety lock before changing spray patterns.
The spray patterns vary as shown below.
1. Select desired spray pattern:
• Select Maximum 0° nozzle setting for stubborn
or hard to reach surface such as second story
surfaces, paint removal, oil stains, rust removal or
other stubborn substances (tar, gum, grease, wax,
etc.).
• Select General 15° nozzle setting for tougher
cleaning tasks. Ideal for removing grease and dirt
from hard surfaces. Also capable of stripping paint
when held at a 45° angle.
• Select Gentle 40° nozzle setting for gentle cleaning
of cars/trucks, boats, RV’s, patio furniture, lawn
equipment, etc.
• Select Fan Spray nozzle setting for optimal high
flow rinsing away of light dirt and debris.
• Select Fan Spray with Soap nozzle setting for
delicate surface cleaning of cars, trucks, childrens
play equipment, patio furniture, etc.
• Select Extended Reach nozzle setting for quick
high flow clean up and long reach cleaning of
second story siding and windows.
• Select Extended Reach with Soap nozzle setting to
propell soap to second story siding and windows.
2. Turn dial until desired spray pattern lines up with
arrow on 7-in-1 nozzle.
Red High Pressure Nozzle
The red high pressure nozzle gives you the most cleaning
power by producing the highest pressure.
Usage Tips
• For most effective cleaning, keep nozzle from 8 to
24 inches away from cleaning surface.
• If you get nozzle too close, especially using a high
pressure spray pattern nozzle, you may damage
surface being cleaned.
• Do Not get closer than 6 inches (15 cm) when
cleaning tires.
0˚ 15˚40˚
Maximum General Gentle Fan Spray Fan Spray
with Soap
Extended Reach Extended Reach
with Soap
High Pressure Mode
High Flow Mode
Not for
Reproduction
11
Applying Detergent
WARNING Chemical Burn Hazard.
Chemicals could cause burns resulting
in death or serious injury.
• Always wear indirect vented (chemical splash) safety
goggles marked to comply with ANSI Z87.1 when using
chemicals.
• DO NOT substitute safety glasses or dry-condition
goggles for indirect vented safety goggles.
• DO NOT use caustic liquid with electric pressure washer.
• Use ONLY pressure washer safe detergents/soaps.
Follow all manufacturers instructions.
To apply detergent, follow these steps:
1. Review use of nozzles shown in How to Use Nozzles.
2. Prepare your detergent solution as required by job to
be performed.
3. Remove cap from detergent tank and fill with
detergent solution. Replace cap.
4. Make sure one of the soap spray pattern nozzles is
selected on 7-in-1 nozzle.
NOTICE Detergent cannot be applied with high pressure
nozzles (red, maximum, general, delicate, fan spray or
extended reach).
5. Make sure garden hose is connected to water inlet
and high pressure hose is connected to spray gun and
high pressure outlet. Turn on water.
6. Start the pressure washer as instructed in How to
Start Your Electric Pressure Washer.
7. Apply detergent to a dry surface, starting at lower
portion of area to be washed and work upward using
long, even, overlapping strokes.
NOTICE High water supply pressure may not allow
detergent to flow. See Troubleshooting.
8. Allow detergent to “soak in” for 3-5 minutes before
washing and rinsing. Reapply as needed to prevent
surface from drying. To prevent streaking, Do Not
allow detergent to dry on surface.
Electric Pressure Washer Rinsing
1. Select desired high pressure nozzle following
instructions How to Use Nozzles.
2. Keep spray gun a safe distance from area you plan to
spray.
WARNING Risk of kickback.
Spray gun could kickback causing you to fall
resulting in death or serious injury.
• Operate the electric pressure washer from a
stable surface.
• Be extremely careful if you must use the electric
pressure washer from a ladder, scaffolding, or any
other similar location.
• Firmly grasp spray gun with both hands when using
power spray modes to avoid injury when spray gun
kicks back.
3. Apply a high pressure spray to a small area and then
check surface for damage. If no damage is found, you
can assume it is okay to continue rinsing.
4. Start at top of area to be rinsed, working down with
same overlapping strokes as you used for cleaning.
Other Cleaning Tips
• NEVER leave the electric pressure washer unattended
while it is plugged into an electrical outlet and while
water is supplied to the equipment.
• If you have the nozzle too far away from the surface
being washed, the cleaning may not be as effective.
How to Store Accessories
The unit is equipped with an accessory tray with places
to store your high pressure hose, spray gun, nozzle
extension, 7-in-1 nozzle and power cord. The red high
pressure nozzle can be stored on end of nozzle extension.
Identify all accessories with the illustrations in Features and
Controls.
Not for
Reproduction
12 BRIGGSandSTRATTON.COM
Maintenance
General Recommendations
Regular maintenance will improve the performance and
extend the life of the electric pressure washer.
The electric pressure washer’s warranty does not cover
items that have been subjected to operator abuse or
negligence. To receive full value from the warranty, the
operator must maintain the electric pressure washer as
instructed in this manual, including proper storage.
NOTICE Should you have questions about replacing
components on your electric pressure washer, please call
(800) 743-4115 for assistance.
NOTICE Your electric pressure washer was designed
and intended to be used with POWERflow+ components
ONLY. Using components that are not designed for
POWERflow+ will cause your pressure washer to not
function optimally.
Before Each Use
1. Clean debris.
2. Check water inlet screen for debris or damage.
3. Check high pressure hose for leaks.
4. Check spray gun operation.
Electric Pressure Washer Maintenance
Clean Debris
Daily or before use, clean accumulated debris from electric
pressure washer. Inspect cooling air slots and openings on
the front, rear and bottom of the electric pressure washer.
These openings must be kept clean and unobstructed.
The electric pressure washer parts should be kept clean to
reduce the risk of overheating and ignition of accumulated
debris.
• Use a damp cloth to wipe exterior surfaces clean.
NOTICE Improper treatment of the electric pressure
washer can damage it and/or shorten its life.
• DO NOT insert any objects through cooling slots.
Check and Clean Water Inlet Screen
Examine the screen on the unit’s water inlet. Clean it if the
screen is clogged or replace it if screen is damaged.
Check High Pressure Hose
The high pressure hose can develop leaks from wear,
kinking, or abuse. Inspect the hose each time before
using it. Check for cuts, leaks, abrasions or bulging of
cover, damage or movement of couplings. If any of these
conditions exist, replace the hose immediately.
WARNING The high pressure stream of water that
this equipment produces could cut through skin
and its underlying tissues, resulting in serious
injury and possible amputation.
• NEVER repair high pressure hose. Replace it.
• Replacement hose rating MUST equal or exceed
maximum pressure rating of unit.
Check Spray Gun
Examine hose connection to spray gun and make sure
it is secure. Test trigger by pressing trigger lock button
and making sure trigger “springs back” into place when
you release it. You should not be able to press trigger
without pressing trigger lock button. Replace spray gun
immediately if it fails any of these tests.
Nozzle Maintenance
Excessive pump pressure can cause a pulsing sensation
felt while squeezing the spray gun trigger. The principal
cause of excessive pump pressure is a nozzle clogged or
restricted with foreign materials such as dirt, etc. A clogged
nozzle could lead to pump cycling ON/OFF or not turning
on even when there is some flow.
To correct the problem, immediately clean the nozzle by
following these instructions:
1. Press master ON/OFF switch to OFF (0) position.
Remove power cord plug from electrical outlet.
2. Disconnect water supply at the electric pressure
washer.
3. ALWAYS point spray gun in a safe direction, press
trigger lock button and squeeze spray gun trigger to
release retained high water pressure.
WARNING The high pressure stream of water that
this equipment produces could cut through skin
and its underlying tissues, resulting in serious
injury and possible amputation.
Spray gun traps high water pressure, even when motor
is stopped and water is disconnected, which could result
in serious injury.
• Keep high pressure hose connected to pump and
spray gun while system is pressurized.
• ALWAYS point spray gun in safe direction, squeeze
spray gun trigger to release high pressure, every time
you turn off pressure washer.
4. Remove 7-in-1 nozzle from end of nozzle extension.
5. Use provided nozzle cleaning tool or small paper clip
to free any foreign material clogging or restricting any
of the nozzles.
6. Using a garden hose, remove additional debris by
back flushing water through nozzle extension. Back
flush between 30 to 60 seconds.
Not for
Reproduction
13
7. Reinstall 7-in-1 nozzle into nozzle extension.
8. Reconnect nozzle extension to spray gun.
9. Make sure garden hose is connected to water inlet.
Check that high pressure hose is connected to spray
gun. Turn on water.
10. Plug power cord into electrical outlet and press master
ON/OFF switch to pressure washer ON (I) position.
11. Test the electric pressure washer by operating with
each nozzle setting.
Pump and Motor Maintenance
The electric pressure washer does not require any
maintenance to the pump or motor. Both assemblies are pre-
lubricated and sealed, requiring no additional lubrication ever.
After Each Use
Water should not remain in the unit for long periods of time.
Sediments or minerals can deposit on pump parts and “freeze”
pump action. Follow these procedures after every use:
1. To ensure detergent tank does not drain during
storage, run electric pressure washer with a soap
spray nozzle until tank is empty.
2. Add 0.5 liter of clean fresh water to detergent tank,
run electric pressure washer with a soap spray nozzle.
Flush for one or two minutes.
3. Press master ON/OFF switch to OFF (0) position.
Remove power cord plug from electrical outlet.
4. Turn off water supply. Point gun in a safe direction,
press trigger lock button and squeeze trigger to relieve
trapped pressure.
5. Disconnect garden hose from water inlet. Disconnect
high pressure hose from spray gun and high pressure
outlet.
6. Drain water from hose and spray gun, then use a cloth
or equivalent to wipe off all exterior surfaces.
7. Drain water from pump by tipping unit onto its right
side (water inlet facing down) for two minutes. Flip
unit over and let rest on high pressure outlet for an
additional two minutes.
8. Wrap high pressure hose and store on top hook of
accessory tray.
9. Coil and store power cord on bottom hook of
accessory tray. Store spray gun, nozzle extension and
7-in-1 nozzle on the accessory tray.
10. Store unit in a clean, dry area.
11. If storing for more than 30 days see Winter or Long
Term Storage.
Winter or Long Term Storage
Follow steps 1-10 in After Each Use.
NOTICE Water left in pump could freeze and permanently
damage pump. Freeze damage is not covered under
warranty.
Protecting the Pump
To protect the pump from damage caused by mineral
deposits or freezing, use PumpSaver, Model 6039, to treat
pump. This prevents freeze damage and lubricates plunger
and seals.
NOTICE PumpSaver is available as an optional
accessory. It is not included with the electric pressure
washer. Contact the nearest authorized service center to
purchase Pump Saver.
NOTICE You must protect your unit from freezing
temperatures.
• Failure to do so will permanently damage your pump
and render your unit inoperable.
• Freeze damage is not covered under warranty.
To use PumpSaver, make sure electric pressure washer
is turned off and inlet and outlet hoses are disconnected.
Read and follow all instructions and warnings given on the
PumpSaver container.
Final Storage Procedures
1. Wrap high pressure hose and store on top hook of
accessory tray.
2. Coil and store power cord on bottom hook of
accessory tray.
3. Store spray gun, nozzle extension and 7-in-1 nozzle
on the accessory tray.
4. Store unit in a clean, dry area that is protected from
freezing temperatures.
5. Cover unit with a suitable protective cover that does
not retain moisture.
Not for
Reproduction
14 BRIGGSandSTRATTON.COM
Troubleshooting
Problem Cause Correction
Pump has following problems:
failure to produce pressure,
erratic pressure, chattering,
loss of pressure, low water
volume.
1. Water inlet is blocked.
2. Inadequate water supply.
3. Garden hose is kinked or leaking.
4. Clogged water inlet screen.
5. Water supply is over 100°F
(38°C).
6. High pressure hose is blocked or
leaks.
7. Nozzle is obstructed.
8. Pump is faulty.
1. Clear inlet.
2. Provide adequate water flow.
3. Straighten garden hose or replace if
leaking.
4. Check and clean water inlet screen.
5. Provide cooler water supply.
6. Clear blocks in high pressure hose or
replace hose.
7. Clean spray tip.
8. Contact authorized service center.
Unit fails to start when spray
gun trigger is squeezed.
1. Water supply is not turned on.
2. Unit is not turned on.
3. Garden hose is too long.
4. Fuse blown or circuit breaker
tripped.
1. Turn on water supply.
2. Press master ON/OFF switch to ON (I)
position. Reset GFCI.
3. Use only 50 ft. (15.24 m) maximum
garden hose.
4. a.) Check fuse box for blown fuse and
replace as necessary or reset circuit
breaker. Do not use a fuse or circuit
breaker with a higher rating than that
specified for your particular branch
circuit.
b.) Disconnect other electrical
appliances and turn off lights in the
circuit or operate the pressure washer
on its own dedicated circuit.
c.) Run pressure washer in any
POWERflow+ High Flow Mode (
)
nozzle setting for 10 minutes. Motor
break in may be necessary.
Detergent fails to mix with
spray.
1. High pressure or high flow without
soap nozzle is selected.
2. Inlet water supply pressure too
high.
1. Select a high flow soap nozzle setting
(indicated with bubbles).
2. Slowly close water supply valve until
chemical just starts to draw (soap suds
will appear when chemical starts to
draw).
Hose connections leaking.
1. Garden hose loose to water inlet.
2. Loose high pressure hose
connections.
3. Damaged o-ring.
1. Hand tighten garden hose to water
inlet.
2. Remove hose completely and reinstall
hand tight.
3. Replace o-ring supplied with unit.
Not for
Reproduction
15
80011059_EN Rev -
BRIGGS & STRATTON PRODUCTS WARRANTY POLICY January 2014
LIMITED WARRANTY
Briggs & Stratton warrants that, during the warranty period specified below, it will repair or replace, free of charge, any part that is defective in material or workmanship
or both. Transportation charges on product submitted for repair or replacement under this warranty must be borne by purchaser. This warranty is effective for
and is subject to the time periods and conditions stated below. For warranty service, find the nearest Authorized Service Dealer in our dealer locator map at
BRIGGSandSTRATTON.COM The purchaser must contact the Authorized Service Dealer, and then make the product available to the Authorized Service Dealer for
inspection and testing.
There is no other express warranty. Implied warranties, including those of merchantability and fitness for a particular purpose, are limited to the
warranty period listed below, or to the extent permitted by law. Liability for incidental or consequential damages are excluded to the extent exclusion
is permitted by law. Some states or countries do not allow limitations on how long an implied warranty lasts, and some states or countries do not allow the exclusion
or limitation of incidental or consequential damages, so the above limitation and exclusion may not apply to you. This warranty gives you specific legal rights and you
may also have other rights which vary from state to state or country to country.**
WARRANTY PERIOD
** In Australia - Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major
failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be
of acceptable quality and the failure does not amount to a major failure. For warranty service, find the nearest Authorized Service Dealer in our dealer locator map at
BRIGGSandSTRATTON.COM, or by calling 1300 274 447, or by emailing or writing to [email protected], Briggs & Stratton Australia Pty Ltd, 1
Moorebank Avenue, NSW, Australia, 2170.
The warranty period begins on the date of purchase by the first retail or commercial consumer. “Consumer use” means personal residential household use by a retail
consumer. “Commercial use” means all other uses, including use for commercial, income producing or rental purposes. Once a product has experienced commercial
use, it shall thereafter be considered as a commercial use product for purposes of this warranty.
To ensure prompt and complete warranty coverage, register your product at the website shown above or at www.onlineproductregistration.com, or mail the complete
registration card (if provided), or call 1-800-743-4115 (in USA).
Save your proof of purchase receipt. If you do not provide proof of the initial purchase date at the time warranty service is requested, the manufacturing date of the
product will be used to determine the warranty period. Product registration is not required to obtain warranty service on Briggs & Stratton products.
ABOUT YOUR WARRANTY
Warranty service is available only through Briggs & Stratton Authorized Service Dealers. Most warranty repairs are handled routinely, but sometimes requests for
warranty service may not be appropriate. This warranty covers only defects in materials or workmanship. It does not cover damage caused by improper use or abuse,
improper maintenance or repair, normal wear and tear, or stale or unapproved fuel.
Improper Use and Abuse - The proper, intended use of this product is described in the Operator’s Manual. Using the product in a way not described in the Operator’s
Manual or using the product after it has been damaged will not be covered under this warranty. Warranty coverage will also not be provided if the serial number on the
product has been removed or the product has been altered or modified in any way, or if the product has evidence of abuse such as impact damage or water/chemical
corrosion damage.
Improper Maintenance or Repair - This product must be maintained according to the procedures and schedules provided in the Operator’s Manual, and serviced or
repaired using genuine Briggs & Stratton parts or equivalent. Damage caused by lack of maintenance or use of non-original parts is not covered by warranty.
Normal Wear and Tear - Like most mechanical devices, your unit is subject to wear even when properly maintained. This warranty does not cover repairs when normal
use has exhausted the life of a part or the equipment. Maintenance and wear items such as filters, belts, cutting blades, and brake pads (except engine brake pads) are
not covered by warranty due to wear characteristics alone, unless the cause is due to defects in material or workmanship.
Stale or Unapproved Fuel - In order to function correctly, this product requires fresh fuel that conforms to the criteria specified in the Operator’s Manual. Engine or
equipment damage caused by stale fuel or the use of unapproved fuels (such as E15 or E85 ethanol blends) is not covered by warranty.
Other Exclusions - This warranty excludes damage due to accident, abuse, modifications, alterations, improper servicing, freezing or chemical deterioration.
Attachments or accessories that were not originally packaged with the product are also excluded. There is no warranty coverage on equipment used for primary power in
place of utility power or on equipment used in life support applications. This warranty does not include used, reconditioned, second-hand, or demonstration equipment or
engines. This warranty also excludes failures due to acts of God and other force majeure events beyond the manufacturer’s control.
Consumer Use Commercial Use
12 months None
Not for
Reproduction
16 BRIGGSandSTRATTON.COM
Product Specifications
Max Outlet Pressure .............1800 PSI* @ 1.0 GPM
Max Flow Rate ...................4.0 GPM* @ 100 PSI
Detergent Mix ..................See MFR’s Instructions
Water Supply Temperature ... Not to exceed 100°F (38°C)
Motor ..........................Universal (brush) Type
Rated Voltage ...........................120 Volts AC
Current...................................13.0 Amps
Briggs & Stratton Corporation
P.O. Box 702
Milwaukee, Wisconsin, 53201-0702 U.S.A.
(800) 743-4115
Electric Pressure Washer
*
This pressure washer is rated in accordance to the Pressure Washer Manufacturers Association (PWMA) standard
PW101-2010 (Testing and Rating Performance of Pressure Washers).
Not for
Reproduction
Ce nettoyeur à haute pression est évalué conformément à la norme PW101-
2010 (essai et évaluation de la performance des nettoyeurs à haute pression)
de l'Association des fabricants de nettoyeurs à haute pression (PWMA)
BRIGGS & STRATTON CORPORATION
MILWAUKEE, WISCONSIN, ÉTATS-UNIS.
Nettoyeur à haute pression
électrique
MANUEL D'UTILISATION
POWERflow+ TECHNOLOGY™
Not for
Reproduction
2 BRIGGSandSTRATTON.COM
Merci d’avoir acheté ce nettoyeur à haute pression électrique de qualité Briggs & Stratton®. Nous sommes heureux que
vous fassiez confiance à la marque Briggs & Stratton. Si vous respectez les instructions d’utilisation et d’entretien de ce
manuel, vous serez en mesure de profiter de votre nettoyeur à haute pression électrique sans fil de Briggs & Stratton
durant de nombreuses années.
Ce manuel contient des renseignements sur la sécurité pour vous informer des dangers et des risques associés aux
nettoyeurs à haute pression électriques ainsi que de la façon de les éviter. Comme Briggs & Stratton ne connaît pas
nécessairement tous les contextes dans lesquels ce nettoyeur à haute pression électrique peut être utilisé, il est important
de lire et de bien comprendre ces instructions avant de tenter de démarrer ou d’utiliser cet équipement. Conservez ces
instructions d'origine pour vous y référer ultérieurement.
Ce nettoyeur à haute pression électrique exige un assemblage final avant utilisation. Consultez les directives sur
les procédures d’assemblage finales de la section Assemblage de ce manuel. Suivez la totalité des instructions.
Comment nous joindre
Vous n’aurez jamais à chercher bien loin pour trouver un centre de soutien et de service Briggs & Stratton pour votre
nettoyeur à haute pression électrique. Consultez les Pages Jaunes. Il y a plus de 30 000 concessionnaires agréés
Briggs & Stratton, partout dans le monde, qui fournissent des services de qualité. Vous pouvez aussi téléphoner au
Service à la clientèle de Briggs & Stratton au (800) 743-4115 ou communiquer avec ce service par Internet à l'adresse
BRIGGSandSTRATTON.COM.
Nettoyeur à haute pression électrique
Numéro de modèle __________________________
Révision __________________________________
Numéro de série ____________________________
Date d'achat ______________________________
Droit d'auteur © 2017. Briggs & Stratton Corporation
Milwaukee, WI, É.-U. Tous droits réservés.
Table des matières
Sécurité de l'utilisateur ........................ 3
Assemblage ................................ 6
Caractéristiques et commandes ................ 8
Utilisation................................... 9
Entretien ..................................12
Entreposage ...............................13
Dépannage ................................14
Garantie...................................15
Spécifications ..............................16
Not for
Reproduction
3
Sécurité de l’utilisateur
CONSERVEZ CES DIRECTIVES
Description de l’équipement
Nous nous sommes efforcés de nous assurer que les
informations contenues dans ce manuel soient exactes
et actualisées. Toutefois, nous nous réservons le droit de
changer, de modifier ou même d’améliorer le produit et ce
document à tout moment sans préavis de notre part.
Cet appareil ISM est conforme à la norme NMB-001 du
Canada.
POWERflow+ Technology
L’appareil avec POWERflow+ Technology est un nettoyeur
à haute pression ultra performant offrant à la fois la haute
pression pour soulever la saleté ET un débit élevé pour
l’éliminer facilement. En mode haut débit, le procédé
POWERflow+ Technology améliore l’opération de
nettoyage en offrant une portée étendue, un savonnage
puissant et un rinçage plus rapide.
La force du procédé POWERflow+ réside dans les deux
modes de nettoyage distincts de la pompe : haute pression
et haut débit. Le mode haute pression fournit jusqu’à 1800
PSI (livres par pouce carré) et convient parfaitement au
nettoyage des taches les plus tenaces, de la moisissure et
des salissures des terrasses en bois, des entrées de cour
et des revêtements, tandis que le mode débit élevé, en
fournissant jusqu’à 4 GPM (gallons par minute), permet le
rinçage en puissance des saletés, du savon et des débris.
Le mode haut débit est également idéal pour laver les
surfaces délicates telles que les meubles de terrasse, les
véhicules et les jeux de plein air et jouets pour enfants.
Le procédé POWERflow+ Technology de Briggs & Stratton
est un système de composants fonctionnant ensemble
pour offrir une capacité de haut débit. L’eau est acheminée
par la pompe dans le boyau spécialement conçu de
8 m (26 pi) puis vers le pistolet développé sur mesure
POWERflow+ muni d’une poignée à prise confortable. L’eau
s’écoule ensuite dans l’embout exclusif 7 en 1 qui permet
à l’utilisateur de passer de la haute pression au haut débit
sans changer d’embout et envoie le jet d’eau jusqu’à 30 pi.
Protection par un disjoncteur de fuite de terre
Le nettoyeur à haute pression électrique est pourvu d’un
disjoncteur de fuite de terre intégré à la fiche électrique du
cordon d’alimentation. Ce dispositif offre une protection
additionnelle contre les risques d’électrocution. Si un
remplacement de la fiche électrique ou du cordon est
requis, n’utilisez rien d’autre que des pièces de rechange
identiques, munies d’un disjoncteur de fuite de terre.
Arrêt automatique
Le nettoyeur à haute pression électrique est muni d’un
capteur qui détecte l’arrêt du jet d’eau lorsque la détente
du pistolet de pulvérisation est relâchée ou verrouillée. Le
capteur provoque l’arrêt du moteur du moment que la détente
du pistolet de pulvérisation est relâchée ou verrouillée.
Si le moteur continue de tourner lorsque la détente du
pistolet de pulvérisation est relâchée ou verrouillée,
N’UTILISEZ PAS LA MACHINE. Veuillez téléphoner au
service de dépannage du nettoyeur à haute pression
électrique au (800) 743-4115 pour obtenir de l’aide.
AVIS Le nettoyeur à haute pression électrique est pourvu
d’un interrupteur de mise en marche. Afin de prévenir
tout dommage, l’interrupteur devrait toujours être placé à
la positon OFF (0) lorsque le nettoyeur à haute pression
électrique n’est pas utilisé.
Surcharge du moteur
Le moteur électrique de ce nettoyeur à haute pression
électrique est muni d’un dispositif de protection
contre la surcharge (thermostat). Ce dispositif arrête
automatiquement le moteur si le moteur surchauffe ou
prélève une intensité de courant excessive.
Si le dispositif de protection contre la surcharge se
déclenche, débranchez l’alimentation en plaçant
l’interrupteur d’alimentation principal ON/OFF à la position
OFF (0). Laissez l’appareil refroidir durant 30 minutes.
Puis, placez l’interrupteur d’alimentation principal ON/OFF
à la position ON (I) pour reprendre l’opération.
Informations importantes de sécurité
Veuillez lire et vous assurer de comprendre le manuel
en entier avant de tenter d’assembler, d’utiliser ou de
faire l’entretien de l’appareil. Veuillez suivre les directives
indiquées dans ce manuel. Si vous avez des questions au
sujet de l’appareil, veuillez appeler le Service à la clientèle
au (800) 743-4115. Le service est disponible du lundi au
vendredi de 8h à 17h , heure normale du Centre.
Renseignements et symboles de sécurité
Le symbole d’alerte de sécurité indique un risque de
blessure corporelle possible. Un mot-indicateur (DANGER,
AVERTISSEMENT ou MISE EN GARDE) est utilisé avec
le symbole d’alerte pour indiquer le niveau ou la gravité
du danger. Un symbole de sécurité peut être utilisé pour
représenter le type de danger. Le mot signal REMARQUE
est utilisé pour traiter des pratiques sans rapport avec des
blessures corporelles.
DANGER indique un danger qui, si non évité, causera
la mort ou des blessures sérieuses.
AVERTISSEMENT indique un danger qui, si non évité,
pourrait causer la mort ou des blessures sérieuses.
MISE EN GARDE indique un danger qui, si non évité,
pourrait causer des blessures mineures ou modérées.
Le mot REMARQUE concerne des pratiques sans rapport
avec d’éventuelles blessures.
AVERTISSEMENT L'omission de lire et de se
conformer au manuel de l'utilisateur et à toutes
les directives d'utilisation avant d'utiliser le produit
peut entraîner la mort ou des blessures graves.
• Lisez ce manuel attentivement et prenez bonne
connaissance de votre nettoyeur à haute pression
électrique. Apprenez ses applications, ses limitations
ainsi que tous les risques impliqués.
Brûlure chimique
Choc électrique
Surface glissante Chute
Objets volants
Lire le manuel
Projectile
Injection de liquide
Incendie
Not for
Reproduction
4 BRIGGSandSTRATTON.COM
AVERTISSEMENT L'utilisation du nettoyeur à haute
pression électrique peut laisser des
flaques d'eau et rendre les surfaces
glissantes.
Risque d’effet de recul. Le pistolet de pulvérisation peut
créer un effet de recul susceptible de vous faire tomber
et d'entraîner des blessures graves ou la mort.
• Utilisez le nettoyeur à haute pression électrique à partir
d'une surface stable.
• Ne vous étirez pas et ne vous tenez pas debout sur un
support instable. Gardez les pieds solidement appuyés
et en équilibre en tout temps.
• La surface de nettoyage devrait comporter une pente et
un drain adéquats pour diminuer les risques de chute
provoquées par des surfaces glissantes.
• Soyez très prudent si vous devez utiliser le nettoyeur à haute
pression électrique lorsque vous êtes dans une échelle, un
échafaudage ou un autre emplacement similaire.
• Lorsque vous utilisez un jet à haute pression, saisissez
fermement le pistolet de pulvérisation avec les deux
mains afin d’éviter les risques de blessures entraînées
par les effets de recul.
AVERTISSEMENT Le jet d'eau sous haute pression
produit par cet appareil pourrait entamer la peau
et ses tissus sous-jacents, entraînant de graves
lésions et pouvant conduire à une amputation.
Le pistolet de pulvérisation emprisonne une pression
d'eau élevée, même lorsque le moteur est arrêté et que
l'arrivée d'eau est débranchée, ce qui peut entraîner des
blessures graves.
• NE dirigez JAMAIS le pistolet de pulvérisation en
direction des gens, des animaux ou des plantes.
• Dirigez TOUJOURS le pistolet de pulvérisation dans une
direction sécuritaire, serrez la gâchette du pistolet de
pulvérisation pour relâcher la haute pression à chaque
fois que vous arrêtez le nettoyeur à haute pression.
AVERTISSEMENT Risque de lésion oculaire ou
corporelle. Le jet peut rejaillir sur vous
ou propulser des objets ou causer
des blessures internes entraînant des
blessures graves.
• Portez toujours des lunettes de protection avec ventilation
indirecte (éclaboussures de produits chimiques) conformes
à la norme ANSI Z87.1 lorsque vous utilisez ou que
vous êtes à proximité de cet équipement. Ne remplacez
JAMAIS les lunettes de protection avec ventilation indirecte
par des lunettes de protection ordinaires.
• Apprenez à arrêter le nettoyeur à haute pression et à
libérer la pression rapidement. Maîtrisez les commandes.
• NE laissez PAS les ENFANTS utiliser le nettoyeur à
haute pression électrique.
• Assurez-vous qu’il n’y a pas d’autre personne présente
dans la zone de travail.
• Inspectez le boyau à haute pression avant chaque
utilisation. NE réparez JAMAIS le boyau à haute
pression; remplacez-le.
• NE réparez PAS les raccords non étanches à l’aide de
scellant; remplacez les joints toriques et joints d'étanchéité.
• Gardez toujours le boyau raccordé au nettoyeur à
haute pression électrique et au pistolet de pulvérisation
lorsque le système est sous pression.
• Chaque fois que vous éteignez le nettoyeur à haute
pression électrique, dirigez TOUJOURS le pistolet
vers un endroit sécuritaire lorsque le système est
sous pression et appuyez sur la détente du pistolet de
pulvérisation pour en libérer la haute pression.
• NE dirigez PAS le pistolet de pulvérisation vers des
personnes ou des animaux.
• NE buvez PAS à même les accessoires reliés au boyau.
• NE bloquez PAS le pistolet de pulvérisation dans la
position ouverte.
• NE laissez PAS le pistolet de pulvérisation sans
surveillance lorsque le nettoyeur à haute pression
électrique est en position de marche (I).
• N’utilisez PAS un pistolet de pulvérisation qui n’est pas
muni d’un verrou d’arme ou d’un pontet installé et en
ordre de marche.
• Assurez-vous toujours que le pistolet de pulvérisation et
que les accessoires sont bien fixés.
• Soyez vigilant, regardez toujours ce que vous faites.
• NE faites PAS fonctionner le produit lorsque vous êtes
fatigué ou sous l’influence de l’alcool ou de drogues.
• Une supervision étroite est requise lorsque ce produit
est utilisé près des enfants.
AVERTISSEMENT Risque d'électrocution.
Le contact avec les deux conducteurs
d'alimentation simultanément peut provoquer un
choc électrique entraînant des blessures graves
voire la mort.
• Inspectez le cordon avant chaque utilisation, N'utilisez
PAS le cordon s'il est endommagé.
• Ce produit est muni d'un disjoncteur de fuite de terre
intégré dans la fiche du cordon d'alimentation. Si le
remplacement de la fiche ou du cordon est nécessaire,
veuillez utiliser des pièces de rechange identiques.
• Gardez tous les branchements secs et hors du sol.
• NE touchez PAS la fiche avec les mains mouillées.
• N'acheminez PAS le cordon d'alimentation par les
portes, les fenêtres, les trous dans les plafonds, les
murs ou les planchers.
• NE marchez PAS sur le cordon d'alimentation.
• NE conduisez pas, ne placez pas et ne tirez pas des
objets sur le cordon d'alimentation.
• NE vaporisez PAS près d'une source d'alimentation.
AVERTISSEMENT Risque d'électrocution.
L'utilisation d'une rallonge peut causer un choc
électrique et des brûlures pouvant entraîner la
mort ou des blessures graves.
• N'utilisez PAS une rallonge avec ce nettoyeur à haute
pression électrique. Les prises du circuit électrique de
votre maison ou une rallonge peuvent ne pas fournir
une protection de survie de coupure de circuit contre
les défauts de terre.
Pour obtenir du service pour les appareils à isolation
double, consultez la section Assemblage.
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
Simplicity ELECTRIC PRESSURE WASHER, BRIGGS & STRATTON POWERFLOW+ [email protected] MODEL 020602-00 Manuel utilisateur
- Catégorie
- Outils de jardin
- Taper
- Manuel utilisateur
- Ce manuel convient également à
dans d''autres langues
Documents connexes
-
Simplicity 020580-00 Manuel utilisateur
-
-
Briggs & Stratton 020680-00 Le manuel du propriétaire
-
Briggs & Stratton 020358-0 Manuel utilisateur
-
-
-
-
-
-
