Leonard LVS1511 Manuel utilisateur
- Catégorie
- Lave-vaisselle
- Taper
- Manuel utilisateur
LVS1511
User Manual
Notice d'utilisation
Dishwasher
Lave-vaisselle
CONTENTS
Safety information 2
Safety instructions 3
Product description 5
Control panel 6
Programmes 7
Settings 8
Before first use 12
Daily use 13
Hints and tips 14
Care and cleaning 16
Troubleshooting 19
Technical information 23
Subject to change without notice.
VISIT OUR WEBSITE TO:
Get usage advice, brochures, trouble shooter, service and repair
information:
www.leonard-hausgeraete.de/support
SAFETY INFORMATION
Before the installation and use of the appliance, carefully
read the supplied instructions. The manufacturer is not
responsible for any injuries or damage that are the result of
incorrect installation or usage. Always keep the instructions
in a safe and accessible location for future reference.
Children and vulnerable people safety
• This appliance can be used by children aged from 8 years
and above and persons with reduced physical, sensory or
mental capabilities or lack of experience and knowledge if
they have been given supervision or instruction concerning
the use of the appliance in a safe way and understand the
hazards involved.
• Children between 3 and 8 years of age and persons with
very extensive and complex disabilities shall be kept away
from the appliance unless continuously supervised.
• Children of less than 3 years of age should be kept away
from the appliance unless continuously supervised.
• Do not let children play with the appliance.
• Keep detergents away from children.
• Keep children and pets away from the appliance when the
door is open.
2 Leonard
• Children shall not carry out cleaning and user maintenance
of the appliance without supervision.
General Safety
• This appliance is intended to be used in household and
similar applications such as:
– farm houses; staff kitchen areas in shops, offices and
other working environments;
– by clients in hotels, motels, bed & breakfast and other
residential type environments.
• Do not change the specification of this appliance.
• The operating water pressure (minimum and maximum)
must be between 0.5 (0.05) / 8 (0.8) bar (MPa)
• Follow the maximum number of 9 place settings.
• If the supply cord is damaged, it must be replaced by the
manufacturer, its Authorised Service Centre or similarly
qualified persons in order to avoid a hazard.
• Put the cutlery in the cutlery basket with the sharp ends
pointing down or put them in the cutlery drawer in a
horizontal position with the sharp edges down.
• Do not leave the appliance with the open door unattended
to avoid stepping accidentally onto it.
• Before any maintenance operation, deactivate the
appliance and disconnect the mains plug from the socket.
• Do not use high pressure water sprays and/or steam to
clean the appliance.
• If the appliance has ventilation openings in the base, they
must not be covered e.g. by a carpet.
• The appliance is to be connected to the water mains using
the new supplied hose-sets. Old hose sets must not be
reused.
SAFETY INSTRUCTIONS
Installation
WARNING! Only a qualified
person must install this
appliance.
• Remove all the packaging.
• Do not install or use a damaged
appliance.
Leonard 3
• Do not use the appliance before
installing it in the built-in structure due
to safety manner.
• Follow the installation instructions
supplied with the appliance.
• Always take care when moving the
appliance as it is heavy. Always use
safety gloves and enclosed footwear.
• Do not install or use the appliance
where the temperature is less than
0 °C.
• Install the appliance in a safe and
suitable place that meets installation
requirements.
Electrical connection
WARNING! Risk of fire and
electric shock.
• The appliance must be earthed.
• Make sure that the parameters on the
rating plate are compatible with the
electrical ratings of the mains power
supply.
• Always use a correctly installed
shockproof socket.
• Do not use multi-plug adapters and
extension cables.
• Make sure not to cause damage to the
mains plug and to the mains cable.
Should the mains cable need to be
replaced, this must be carried out by
our Authorised Service Centre.
• Connect the mains plug to the mains
socket only at the end of the
installation. Make sure that there is
access to the mains plug after the
installation.
• Do not pull the mains cable to
disconnect the appliance. Always pull
the mains plug.
• This appliance is fitted with a 13 A
mains plug. If it is necessary to change
the mains plug fuse, use only a 13 A
ASTA (BS 1362) fuse (UK and Ireland
only).
Water connection
• Do not cause damage to the water
hoses.
• Before connection to new pipes, pipes
not used for a long time, where repair
work has been carried out or new
devices fitted (water meters, etc.), let
the water flow until it is clean and clear.
• Ensure that there are no visible water
leaks during and after the first use of
the appliance.
• The water inlet hose has a safety valve
and a sheath with an inner mains
cable.
WARNING! Dangerous
voltage.
• If the water inlet hose is damaged,
immediately close the water tap and
disconnect the mains plug from the
mains socket. Contact the Authorised
Service Centre to replace the water
inlet hose.
Use
• Do not put flammable products or items
that are wet with flammable products
in, near or on the appliance.
• Dishwasher detergents are dangerous.
Follow the safety instructions on the
detergent packaging.
• Do not drink and play with the water in
the appliance.
• Do not remove the dishes from the
appliance until the programme is
complete. Some detergent may remain
on the dishes.
• Do not store items or apply pressure on
the open door of the appliance.
• The appliance can release hot steam if
you open the door while a programme
operates.
4 Leonard
Internal lighting
WARNING! Risk of injury.
• Concerning the lamp(s) inside this
product and spare part lamps sold
separately: These lamps are intended
to withstand extreme physical
conditions in household appliances,
such as temperature, vibration,
humidity, or are intended to signal
information about the operational status
of the appliance. They are not intended
to be used in other applications and are
not suitable for household room
illumination.
• To replace the internal lighting, contact
the Authorised Service Centre.
Service
• To repair the appliance contact the
Authorised Service Centre. Use original
spare parts only.
• Please note that self-repair or non-
professional repair can have safety
consequences and might void the
guarantee.
• The following spare parts will be
available for 7 years after the model
has been discontinued: motor,
circulation and drain pump, heaters and
heating elements, including heat
pumps, piping and related equipment
including hoses, valves, filters and
aquastops, structural and interior parts
related to door assemblies, printed
circuit boards, electronic displays,
pressure switches, thermostats and
sensors, software and firmware
including reset software. Please note
that some of these spare parts are only
available to professional repairers, and
that not all spare parts are relevant for
all models.
• The following spare parts will be
available for 10 years after the model
has been discontinued: door hinge and
seals, other seals, spray arms, drain
filters, interior racks and plastic
peripherals such as baskets and lids.
Disposal
WARNING! Risk of injury or
suffocation.
• Disconnect the appliance from the
mains supply.
• Cut off the mains cable and discard it.
• Remove the door catch to prevent
children and pets to get closed in the
appliance.
PRODUCT DESCRIPTION
The graphics below is just a
general product overview. For
more detailed information, refer
to other chapters and/or
documents provided with the
appliance.
Leonard 5
4
3
7
8
10 9
56
11
1
2
1
Upper spray arms
2
Lower spray arm
3
Filters
4
Rating plate
5
Salt container
6
Air vent
7
Rinse aid dispenser
8
Detergent dispenser
9
Cutlery basket
10
Lower basket
11
Upper basket
CONTROL PANEL
4
32
1
1
On/off button / Reset button
2
Programme indicators
3
Indicators
4
Programme button
6 Leonard
Indicators
Indicator Description
Drying phase indicator. It is on when you select a programme with the drying
phase. It flashes when the drying phase operates.
Salt indicator. It is on when the salt container needs refilling. It is always off
while the programme operates.
PROGRAMMES
The order of the programmes in the table
may not reflect their sequence on the
control panel.
Programme Type of load Degree of soil Programme phases
1)
• Crockery
• Cutlery
• Pots
• Pans
• Normal
• Lightly dried-on
• Prewash
• Wash 50 °C
• Intermediate rinse
• Final rinse 60 °C
• Drying
• AirDry
• Crockery
• Cutlery
• Pots
• Pans
• Normal to
heavy
• Dried-on
• Prewash
• Wash 60 °C
• Intermediate rinse
• Final rinse 60 °C
• Drying
• AirDry
• Crockery
• Cutlery
• Pots
• Pans
• Normal
• Lightly dried-on
• Wash 60 °C
• Intermediate rinse
• Final rinse 55 °C
• Drying
• AirDry
• Crockery
• Cutlery
• Fresh • Wash 50 °C
• Intermediate rinse
• Final rinse 50 °C
• AirDry
2)
• All types of
loads
• All degrees of
soil
• Prewash
1)
This is the longest programme offering the most efficient use of energy and water consumption for crockery
and cutlery with normal soil. This is the standard programme for test institutes. This programme is used to assess
compliance with the Ecodesign Comission Regulation (EU) 2019/2022.
2)
This is a programme for rinsing off food remains from the dishes. It prevents odours forming in the appliance.
Do not use detergent with this programme.
Leonard 7
Consumption values
Programme
1)
2)
Water
(l)
Energy
(kWh)
Duration
(min)
9.9
3)
/ 9.9
4)
0.778
3)
/ 0.779
4)
240
3)
/ 240
4)
10.5 - 12.8 0.888 - 1.086 160
9.5 - 11.7 0.713 - 0.871 90
8.7 -10.6 0.542 - 0.663 30
2.9 - 3.6 0.012 - 0.015 15
1)
The pressure and the temperature of the water, the variations of the mains supply, the options and the quantity
of dishes can change the values.
2)
The values for programmes other than ECO are indicative only.
3)
In accordance with the 1016/2010 regulation.
4)
In accordance with the 2019/2022 regulation.
Information for test institutes
To receive the necessary information for
conducting performance tests (e.g.
according to EN60436), send an email to:
In your request please include the product
number code (PNC) found on the rating
plate.
For any other questions regarding your
dishwasher please refer to the service
book provided with your appliance.
SETTINGS
Programme selection mode and
user mode
When the appliance is in programme
selection mode it is possible to set a
programme and to enter user mode.
Settings available in the user mode:
• The level of water softener according to
the water hardness.
• The level of rinse aid according to the
required dosage.
• Activation or deactivation of the
acoustic signal for the end of a
programme.
• Activation or deactivation of the AirDry.
As the appliance stores the saved
settings, there is no need to configure
it before every cycle.
How to set the programme
selection mode
The appliance is in programme selection
mode when the programme indicator
flashes.
After activation, the appliance is in
programme selection mode by default. If
not, set the programme selection mode
the following way:
Press and hold the on/off button until the
appliance is in programme selection
mode.
8 Leonard
How to enter user mode
Make sure the appliance is in programme
selection mode.
To enter the user mode, press and hold
the programme button until the indicator
flashes and the indicators ,
and are on.
The water softener
The water softener removes minerals from
the water supply, which would have a
negative effect on the washing results and
on the appliance.
The higher the content of these minerals,
the harder your water is. Water hardness
is measured in equivalent scales.
The water softener should be adjusted
according to the hardness of the water in
your area. Your local water authority can
advise you on the hardness of the water in
your area. It is important to set the right
level of the water softener to assure good
washing results.
Water hardness
German de‐
grees (°dH)
French de‐
grees (°fH)
mmol/l Clarke de‐
grees
Water softener
level
47 - 50 84 - 90 8.4 - 9.0 58 - 63 10
43 - 46 76 - 83 7.6 - 8.3 53 - 57 9
37 - 42 65 - 75 6.5 - 7.5 46 - 52 8
29 - 36 51 - 64 5.1 - 6.4 36 - 45 7
23 - 28 40 - 50 4.0 - 5.0 28 - 35 6
19 - 22 33 - 39 3.3 - 3.9 23 - 27
5
1)
15 - 18 26 - 32 2.6 - 3.2 18 - 22 4
11 - 14 19 - 25 1.9 - 2.5 13 - 17 3
4 - 10 7 - 18 0.7 - 1.8 5 - 12 2
<4 <7 <0.7 < 5
1
2)
1)
Factory setting.
2)
Do not use salt at this level.
Regardless of the type of detergent
used, set the proper water hardness
level to keep the salt refill indicator
active.
Multi-tabs containing salt are
not effective enough to soften
hard water.
Regeneration process
For the correct water softener operation,
the resin of the softener device needs to
be regenerated regularly. This process is
automatic and is the part of the normal
dishwasher operation.
When the prescribed quantity of water
(see values in the table) has been used
since the previous regeneration process, a
new regeneration process will be initiated
between the final rinse and the
programme end.
Leonard 9
Water softener
level
Amount of water
(l)
1 250
2 100
3 62
4 47
5 25
6 17
7 10
8 5
9 3
10 3
In case of the high water softener setting,
it may occur also in the middle of the
programme, before the rinse (twice during
a programme). Regeneration initiation has
no impact on the cycle duration, unless it
occurs in the middle of a programme or at
the end of a programme with a short
drying phase. In that cases, the
regeneration prolongs the total duration of
a programme by additional 5 minutes.
Subsequently, the rinsing of the water
softener that lasts 5 minutes may begin in
the same cycle or at the beginning of the
next programme. This activity increases
the total water consumption of a
programme by additional 4 litres and the
total energy consumption of a programme
by additional 2 Wh. The rinsing of the
softener ends with a complete drain.
Each performed softener rinse (possible
more than one in the same cycle) may
prolong the programme duration by
another 5 minutes when it occurs at any
point at the beginning or in the middle of a
programme.
All the consumption values
mentioned in this section are
determined in accordance with
the currently applicable
standard in laboratory
conditions with water hardness
2.5mmol/L according to the
2019/2022 regulation (water
softener: level 3).
The pressure and the
temperature of water as well as
the variations of the mains
supply can change the values.
How to set the water softener
level
Make sure the appliance is in user mode.
1. Wait until the indicator starts to
flash, the indicator continues to
flash and the remaining indicators are
off.
The intermittent flashing of the indicator
shows the current setting: e.g. 5
flashes + pause + 5 flashes = level 5.
2. Press the programme button
repeatedly to change the setting. Each
pressing of the programme button
increases the level number. After
reaching the level 10, the count starts
again from the level 1.
3. Press the on/off button to confirm the
setting.
The rinse aid level
The rinse aid helps to dry the dishes
without streaks and stains. It is
automatically released during the hot rinse
phase.
It is possible to set the released quantity
of rinse aid between level 1 (minimum
quantity) and level 8 (maximum quantity).
Factory setting: level 5.
When the rinse aid chamber is empty, the
rinse aid indicator is on, notifying to refill
rinse aid. If the drying results are
satisfactory while using multi-tablets only,
it is possible to deactivate the dispenser
10 Leonard
and the indicator. However, for the best
drying performance, always use rinse aid
and keep the rinse aid indicator active.
To deactivate the rinse aid dispenser and
indicator, set the level of rinse aid to 0.
How to set the rinse aid level
Make sure the appliance is in user mode.
1. Press the programme button
immediately.
The indicator
starts to flash.
2. Wait until the indicator continues to
flash and the remaining programme
indicators are off.
The intermittent flashing of the indicator
shows the current setting: e.g. 5
flashes + pause + 5 flashes = level 5.
3. Press the programme button
repeatedly to change the setting. Each
pressing of the programme button
increases the level number. After
reaching the level 8, the count starts
again from the level 0. The level 0
means that the rinse aid dispensing is
disabled.
4. Press the on/off button to confirm the
setting.
Acoustic signals
Acoustic signals sound when a
malfunction of the appliance occurs. It is
not possible to deactivate these acoustic
signals.
There is also an acoustic signal that
sounds when the programme is
completed. By default this acoustic signal
is deactivated but it is possible to activate
it.
How to activate the acoustic
signal for the end of the
programme
Make sure the appliance is in user mode.
1. Press the programme button twice.
The indicator starts to flash.
2. Wait until the indicator continues
to flash and the remaining programme
indicators are off.
The indicator shows the current
setting:
• is off = The acoustic signal is
off.
• is on = The acoustic signal is
on.
3. Press the programme button to
change the setting.
4. Press the on/off button to confirm the
setting.
AirDry
AirDry improves the drying results with
less energy consumption.
During the drying phase, the
door opens automatically and
remains ajar.
CAUTION! Do not try to close
the appliance door within 2
minutes after automatic
opening. This can cause
damage to the appliance.
AirDry is automatically activated with all
programmes excluding (if applicable).
CAUTION! If children have
access to the appliance, it is
advised to deactivate AirDry as
opening the door may pose a
danger.
Leonard 11
How to deactivate the AirDry
Make sure the appliance is in user mode.
1. Press the programme button three
times.
The indicator starts to flash.
2. Wait until the indicator
continues
to flash and the remaining programme
indicators are off.
The indicator shows the current
setting:
• is off = AirDry is off.
• is on = AirDry is on.
3. Press the programme button to
change the setting.
4. Press the on/off button to confirm the
setting.
BEFORE FIRST USE
1. Make sure that the current level of
the water softener agrees with the
hardness of the water supply. If not,
adjust the level of the water
softener.
2. Fill the salt container.
3. Fill the rinse aid dispenser.
4. Open the water tap.
5. Start a programme to remove any
processing residuals that can still be
inside the appliance. Do not use
detergent and do not put dishes in the
baskets.
After starting the programme, the
appliance recharges the resin in the water
softener for up to 5 minutes. The washing
phase starts only after this procedure is
complete. The procedure is repeated
periodically.
The salt container
CAUTION! Use rough salt
designed for dishwashers only.
Fine salt increases the risk of
corrosion.
The salt is used to recharge the resin in
the water softener and to assure good
washing results in daily use.
How to fill the salt container
1. Turn the cap of the salt container
counterclockwise and remove it.
2. Put 1 litre of water in the salt container
(only for the first time).
3. Fill the salt container with 1 kg of salt
(until it is full).
4. Carefully shake the funnel by its
handle to get the last granules inside.
5. Remove the salt around the opening of
the salt container.
6. Turn the cap of the salt container
clockwise to close the salt container.
CAUTION! Water and salt can
come out of the salt container
when you fill it. After you fill the
salt container, immediately
start a programme to prevent
corrosion.
12 Leonard
How to fill the rinse aid
dispenser
B
C
D
A
CAUTION! Only use rinse aid
designed specifically for
dishwashers.
1. Press the release element (A) to open
the lid (B).
2. Pour the rinse aid in the dispenser (C)
until the liquid reaches the marking
"FILL".
3. Remove the spilled rinse aid with an
absorbent cloth to prevent excessive
foam formation.
4. Close the lid. Make sure that the lid
locks into position.
Fill the rinse aid dispenser
when the indicator (D) is clear.
DAILY USE
1. Open the water tap.
2. Press the on/off button to activate the
appliance.
Make sure that the appliance is in
programme selection mode.
• If the salt indicator is on, fill the salt
container.
• Make sure that there is rinse aid in
the rinse aid dispenser.
3. Load the baskets.
4. Add the detergent.
5. Set and start the correct programme
for the type of load and the degree of
soil.
Using the detergent
B
C
A
CAUTION! Only use detergent
designed specifically for
dishwashers.
1. Press the release button (B) to open
the lid (C).
2. Put the detergent in the compartment
(A). You can use detergent in tablets,
powder or gel.
3. If the programme has a prewash
phase, put a small quantity of
detergent on the inner part of the
appliance door.
4. Close the lid. Make sure that the lid
locks into position.
Setting and starting a
programme
Starting a programme
1. Keep the appliance door ajar.
2. Press the on/off button to activate the
appliance. Make sure that the
appliance is in programme selection
mode.
3. Press the programme button
repeatedly until the indicator of the
Leonard 13
programme you want to select starts
flashing.
4. Close the appliance door to start the
programme.
Opening the door while the
appliance operates
Opening the door while a programme is
running stops the appliance. It may affect
the energy consumption and the
programme duration. After closing the
door, the appliance continues from the
point of interruption.
If the door is opened for more
than 30 seconds during the
drying phase, the running
programme ends. It does not
happen if the door is opened by
AirDry function.
Do not try to close the
appliance door within 2 minutes
after AirDry automatically
opens it as this may cause
damage to the appliance.
If, afterwards, the door is
closed for at least 3 minutes,
the running programme ends.
Cancelling the programme
Press the on/off button for 3 seconds until
the appliance is in programme selection
mode.
Make sure that there is detergent in the
detergent dispenser before you start a
new programme.
The Auto Off function
This function decreases energy
consumption by deactivating automatically
the appliance when it is not operating.
The function comes into operation:
• When the programme is complete.
• After 5 minutes if a programme was not
started.
End of the programme
When the programme is complete, the
Auto Off function switches the appliance
off.
Close the water tap.
HINTS AND TIPS
General
Follow the hints below to ensure optimal
cleaning and drying results in daily use
and to protect the environment.
• Washing dishes in the dishwasher as
instructed in the user manual usually
consumes less water and energy than
washing dishes by hand.
• Load the dishwasher to its full capacity
to save water and energy. For best
cleaning results, arrange items in the
baskets as instructed in the user
manual and do not overload the
baskets.
• Do not pre-rinse dishes by hand. It
increases the water and energy
consumption. When needed, select a
programme with a prewash phase.
• Remove larger residues of food from
the dishes and empty cups and glasses
before putting them inside the
appliance.
• Soak or slightly scour cookware with
firmly cooked-on or baked-on food
before washing it in the appliance.
• Make sure that items in the baskets do
not touch or cover each other. Only
then can the water completely reach
and wash the dishes.
• You can use dishwasher detergent,
rinse aid and salt separately or you can
use the multi-tablets (e.g. ''All in 1'').
Follow the instructions on the
packaging.
• Select a programme according to the
type of load and the degree of soil.
14 Leonard
offers the most efficient use of
water and energy consumption.
• To prevent limescale buildup inside the
appliance:
– Refill the salt container whenever
necessary.
– Use the recommended dosage of
the detergent and rinse aid.
– Make sure that the current level of
the water softener agrees with the
hardness of the water supply.
– Follow the instructions in the
chapter "Care and cleaning".
Using salt, rinse aid and
detergent
• Only use salt, rinse aid and detergent
designed for dishwasher. Other
products can cause damage to the
appliance.
• In areas with hard and very hard water,
we recommend to use basic
dishwasher detergent (powder, gel,
tablets containing no additional
agents), rinse aid and salt separately
for optimal cleaning and drying results.
• Detergent tablets do not fully dissolve
with short programmes. To prevent
detergent residues on the tableware,
we recommend that you use tablets
with long programmes.
• Always use the correct quantity of
detergent. Insufficient dosage of
detergent can result in poor cleaning
results and hard-water filming or
spotting on the items. Using too much
detergent with soft or softened water
results in detergent residues on the
dishes. Adjust the amount of detergent
based on the water hardness. Refer to
the instructions on the detergent
packaging.
• Always use the correct quantity of rinse
aid. Insufficient dosage of rinse aid
decreases the drying results. Using too
much rinse aid results in bluish layers
on the items.
• Make sure that the water softener level
is correct. If the level is too high, the
increased quantity of salt in the water
might result in rust on cutlery.
What to do if you want to stop
using multi-tablets
Before you start to use separately
detergent, salt and rinse aid, complete the
following steps:
1. Set the highest level of the water
softener.
2. Make sure that the salt and rinse aid
containers are full.
3. Start the shortest programme with a
rinsing phase. Do not add detergent
and do put dishes in the baskets.
4. When the programme is complete,
adjust the water softener according to
the water hardness in your area.
5. Adjust the released quantity of rinse
aid.
Loading the baskets
• Always use the whole space of the
baskets.
• Use the appliance to wash dishwasher-
safe items only.
• Do not wash in the appliance items
made of wood, horn, aluminium, pewter
and copper as they could crack, warp,
get discoloured or pitted.
• Do not wash in the appliance items that
can absorb water (sponges, household
cloths).
• Put hollow items (cups, glasses and
pans) with the opening facing
downwards.
• Make sure that glasses do not touch
each other.
• Put light items in the upper basket.
Make sure that the items do not move
freely.
• Put cutlery and small items in the
cutlery basket.
• Make sure that the spray arms can
move freely before you start a
programme.
Before starting a programme
Before you start the selected programme,
make sure that:
• The filters are clean and correctly
installed.
Leonard 15
• The cap of the salt container is tight.
• The spray arms are not clogged.
• There is enough salt and rinse aid
(unless you use multi-tablets).
• The arrangement of the items in the
baskets is correct.
• The programme is suitable to the type
of load and the degree of soil.
• The correct quantity of detergent is
used.
Unloading the baskets
1. Let the tableware cool down before
you remove it from the appliance. Hot
items can be easily damaged.
2. First remove items from the lower
basket, then from the upper basket.
After the programme is
completed, water can still
remain on the inside surfaces
of the appliance.
CARE AND CLEANING
WARNING! Before
maintenance, deactivate the
appliance and disconnect the
mains plug from the main
socket.
Dirty filters and clogged spray
arms decrease the washing
results. Make a check regularly
and, if necessary, clean them.
Cleaning the filters
The filter system is made of 3 parts.
C
B
A
1. Turn the filter (B) counterclockwise
and remove it.
2. Remove the filter (C) out of filter (B).
3. Remove the flat filter (A).
4. Wash the filters.
16 Leonard
5. Make sure that there are no residues
of food or soil in or around the edge of
the sump.
6. Put back in place the flat filter (A).
Make sure that it is correctly positioned
under the 2 guides.
7. Reassemble the filters (B) and (C).
8. Put back the filter (B) in the flat filter
(A). Turn it clockwise until it locks.
CAUTION! An incorrect
position of the filters can cause
bad washing results and
damage to the appliance.
Cleaning the lower spray arm
We recommend to clean the lower spray
arm regularly to prevent soil from clogging
the holes.
Clogged holes can cause unsatisfactory
washing results.
1. To remove the lower spray arm, pull it
upwards.
2. Wash the spray arm under running
water. Use a thin pointed tool, e.g. a
toothpick, to remove particles of soil
from the holes.
3. To install the spray arm back, press it
downwards.
Leonard 17
Cleaning the upper spray arms
We recommend to clean the upper spray
arms regularly to prevent soil from
clogging the holes. Clogged holes can
cause unsatisfactory washing results.
The upper spray arms are placed under
the upper basket. The spray arms (B) are
installed in the duct (A) with the mounting
elements (C).
A
B
C
1. Pull out the upper basket.
2. To detach the spray arm, turn the
mounting element clockwise.
3. Wash the spray arm under running
water. Use a thin pointed tool, e.g. a
toothpick, to remove particles of soil
from the holes.
4. To install the spray arm back, insert
the mounting element in the spray arm
and fix it in the duct by turning it
counterclockwise. Make sure that the
mounting element locks into place.
External cleaning
• Clean the appliance with a moist soft
cloth.
• Only use neutral detergents.
• Do not use abrasive products, abrasive
cleaning pads or solvents.
Internal cleaning
• Carefully clean the appliance, including
the rubber gasket of the door, with a
soft damp cloth.
• To maintain the performance of your
appliance, use a cleaning product
designed specifically for dishwashers at
least once a month. Carefully follow the
instructions on the packaging of the
product.
• Do not use abrasive products, abrasive
cleaning pads, sharp tools, strong
chemicals, scourer or solvents.
18 Leonard
• Using short-duration programmes
regularly can cause grease and
limescale buildup inside the appliance.
Run long-duration programmes at least
twice a month to prevent the buildup.
Removal of foreign objects
Check the filters and the sump after each
use of the dishwasher. Foreign objects
(e.g. pieces of glass, plastic, bones or
toothpicks, etc) decrease the cleaning
performance and can cause damage to
the drain pump.
1. Disassemble the filters system as
instructed in this chapter.
2. Remove any foreign objects by hand.
CAUTION! If unable to
remove the objects, contact
an Authorised Service
Centre.
3. Reassemble the filters as instructed in
this chapter.
TROUBLESHOOTING
WARNING! Improper repair of
the appliance may pose a
danger to the safety of the
user. Any repairs must be
performed by qualified
personnel.
The majority of problems that can
occur can be solved without the need
to contact an Authorised Service
Centre.
Refer to the below table for information on
possible problems.
With some problems, the dedicated
indicator flashes intermittently to indicate a
malfunction and the alarm code.
Problem and alarm code Possible cause and solution
You cannot activate the appliance. • Make sure that the mains plug is connected to
the mains socket.
• Make sure that there is no damaged fuse in the
fuse box.
The programme does not start. • Make sure that the appliance door is closed.
• The appliance recharges the resin inside the
water softener. The duration of the procedure is
approximately 5 minutes.
The appliance does not fill with water.
• The indicator flashes 1 time in‐
termittently.
• Acoustic signal sounds 1 time inter‐
mittently.
• Make sure that the water tap is open.
• Make sure that the pressure of the water supply
is not too low. For this information, contact your
local water authority.
• Make sure that the water tap is not clogged.
• Make sure that the filter in the inlet hose is not
clogged.
• Make sure that the inlet hose has no kinks or
bends.
Leonard 19
Problem and alarm code Possible cause and solution
The appliance does not drain the wa‐
ter.
• The indicator flashes 2 times in‐
termittently.
• Acoustic signal sounds 2 times in‐
termittently.
• Make sure that the sink spigot is not clogged.
• Make sure that the interior filter system is not
clogged.
• Make sure that the drain hose has no kinks or
bends.
The anti-flood device is on.
• The indicator flashes 3 times in‐
termittently.
• Acoustic signal sounds 3 times in‐
termittently.
• Close the water tap.
• Make sure that the appliance is correctly instal‐
led.
• Make sure the baskets are loaded as instructed
in the user manual.
Malfunction of the water level detection
sensor.
• The indicator flashes 4 times in‐
termittently.
• Acoustic signal sounds 4 times in‐
termittently.
• Make sure that the filters are clean.
• Switch the appliance off and on.
Malfunction of the wash pump or the
drain pump.
• The indicator flashes 5 times in‐
termittently.
• Acoustic signal sounds 5 times in‐
termittently.
• Switch the appliance off and on.
The temperature of the water inside
the appliance is too high or malfunction
of the temperature sensor occurred.
• The indicator flashes 6 times in‐
termittently.
• Acoustic signal sounds 6 times in‐
termittently.
• Make sure that the temperature of the inlet wa‐
ter does not exceed 60°C.
• Switch the appliance off and on.
Technical malfunction of the appliance.
• The indicator flashes 12 times
intermittently.
• Acoustic signal sounds 12 times in‐
termittently.
• Switch the appliance off and on.
The level of water inside the appliance
is too high.
• The indicator flashes 15 times
intermittently.
• Acoustic signal sounds 15 times in‐
termittently.
• Switch the appliance off and on.
• Make sure that the filters are clean.
• Make sure that the outlet hose is installed at the
right height above the floor. Refer to the installa‐
tion instructions.
20 Leonard
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
Leonard LVS1511 Manuel utilisateur
- Catégorie
- Lave-vaisselle
- Taper
- Manuel utilisateur
dans d''autres langues
- English: Leonard LVS1511 User manual
Documents connexes
-
Leonard LV1525 Manuel utilisateur
-
-
-
-
-
-
-
-