Haier 50UG6550G Manuel utilisateur

Marque: Haier

Modèle: 50UG6550G

Catégorie: Téléviseurs LED

Taper: Manuel utilisateur

50UG6550G

English

Energy Star

This product qualiﬁes for ENERGY STAR in the factory default setting and this is the setting in which power savings

will be achieved. Changing the factory default picture setting or enabling other features will increase power

consumption that could exceed the limits necessary to qualify for ENERGY STAR rating.

Apparatus shall not be exposed to dripping or splashing and no objects ﬁlled with liquids, such as vases, shall be

placed on the apparatus.

Batteries installed warning

Caution - Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.

The batteries (battery pack or batteries installed) shall not be exposed to excessive heat such as sunshine, ﬁre or the

like.

FOR YOUR SAFETY

Before operating the TV, please read this manual thoroughly. This manual should be retained for future reference.

FCC Class B Radio Frequency Interference Statement

WARNING: (FOR FCC CERTIFIED MODELS)

SYMBOL SYMBOL DEFINITION

DANGEROUS VOLTAGE: The lightning ﬂash with arrowhead symbol, within an equilateral

triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage”

within the product’s enclosure that may be of suﬃcient magnitude to constitute a risk of

electrical shock to persons.

INSTRUCTIONS: The exclamation point within an equilateral triangle is intended to alert the

user to the presence of important operating and maintenance (servicing) instruction in the

literature accompanying the appliance.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant

to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy,

and if not installed and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception, which can be determined by turning

the equipment oﬀ and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

1. Reorient or relocate the receiving antenna.

2. Increase the separation between the equipment and receiver.

3. Connect the equipment into an outlet on a circuit diﬀerent from that to which the receiver is connected.

4. Consult the dealer or an experienced radio/TV technician for help.

NOTICE

1. The changes or modiﬁcations not expressly approved by the party responsible for compliance could void the

user's authority to operate the equipment.

2. Shielded interface cables and AC power cord, if any, must be used in order to comply with the emission limits.

3. The manufacturer is not responsible for any radio or TV interference caused by unauthorized modiﬁcation to

this equipment. It is the responsibilities of the user to correct such interference.

WARNING:

To prevent ﬁre or shock hazard, do not expose the TV to rain or moisture. Dangerously high voltages are present

inside the TV. Do not open the cabinet. Refer servicing to qualiﬁed personnel only.

SA 1965

SA 1966

PRECAUTIONS AND REMINDERS

Notice for Remote Control

Place unit on even surfaces. Unplug immediately if other

foreign materials are put inside TV

box or if the TV fell down.

Do not cover or block any vents

and openings. Inadequate

ventilation may shorten the life of

the display unit and cause

overheating.

Unplug immediately if

malfunction like no video/audio

occurs, or smoke and bad odor

come from TV.

Prohibit/Avoid opening TV

cabinet.

Avoid direct sunlight, dusty,

humid and smoky areas.

Don't throw any object inside the

TV box like metals or other

ﬂammable materials.

Remember to unplug the AC cord

from the AC outlet before

cleaning. Do not use liquid

cleaners or aerosol cleaners to

clean the display.

Call service personnel to clean the

internal part of the TV once a year.

Don't place the TV in conﬁned

spaces or in a box when using it.

Make sure to unplug the unit

when not in use for a long period

of time (days).

Do not place the display near

water, such as bathtub, washbasin,

kitchen sink, laundry tub,

swimming pool or in a damp

basement.

Avoid Dropping Avoid Liquids Avoid Aerosol Cleaners

6 in.

NOTE

English

IMPORTANT SAFETY INSTRUCTIONS

Read before operating equipment.

t To reduce the risk of electric shock or component damage, switch oﬀ the power before connecting other

components to your TV.

t Read these instructions.

t Keep these instructions.

t Heed all warnings.

t Follow all instructions.

t Do not use this apparatus near water.

t Clean only with a dry cloth.

t Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

t Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including

ampliﬁers) that produce heat.

t Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades and a

third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does

not ﬁt into your outlet, consult an electrician for replacement of the obsolete outlet.

t Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the

point where they exit from the apparatus.

t Only use attachments/accessories speciﬁed by the manufacturer.

t Use only with the cart, stand, tripod, bracket, or table speciﬁed by the manufacturer, or sold with the

apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid

injury from tip-over.

t Unplug this apparatus during lightning storms or when unused for long periods of time.

t Refer all servicing to qualiﬁed service personnel. Servicing is required when the apparatus has been

damaged in any way, such as when the power-supply cord or plug is damaged, liquid has been spilled or objects

have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally or

has been dropped.

t Unplug the power cord before cleaning your TV.

t When moving your TV from an area of low temperature to an area of high temperature, condensation may form

in the housing. Wait before turning on your TV to avoid causing ﬁre, electric shock, or component damage.

t A distance of at least three feet should be maintained between your TV and any heat source, such as a radiator,

heater, oven, ampliﬁer etc. Do not install your TV close to smoke. Operating your TV close to smoke or moisture

may cause ﬁre or electric shock.

t Slots and openings in the back and bottom of the cabinet are provided for ventilation. To ensure reliable

operation of your TV and to protect it from overheating, be sure these openings are not blocked or covered. Do

not place your TV in a bookcase or cabinet unless proper ventilation is provided.

t Never push any object into the slots and openings on your TV cabinet. Do not place any objects on the top of

your TV. Doing so could short circuit parts causing a ﬁre or electric shock. Never spill liquids on your TV.

t Your TV should be operated only from the type of power source indicated on the label. If you are not sure of the

type of power supplied to your home, consult your dealer or local power company.

t Do not apply pressure or throw objects at your TV. This may compromise the integrity of the display. The

manufacturer’s warranty does not cover user abuse or improper installations.

t The power cord must be

replaced when using diﬀerent voltage than the voltage speciﬁed. For more information,

contact your dealer.

t When connected to a power outlet, power is always ﬂowing into your TV. To totally disconnect power, unplug

the power cord.

t Do not overload power strips and extension cords. Overloading can result in ﬁre or electric shock.

t The wall socket should be installed near your TV and easily accessible.

t Only power of the marked voltage can be used for your TV. Any other voltage than the speciﬁed voltage may

cause ﬁre or electric shock.

t Do not touch the power cord during lightning. To avoid electric shock, avoid handling the power cord during

electrical storms.

t Unplug your TV during a lightning storm or when it will not be used for long period of time. This will protect your

TV from damage due to power surges.

t Do not attempt to repair or service your TV yourself. Opening or removing the back cover may expose you to

high voltages, electric shock, and other hazards. If repair is required, contact your dealer and refer all servicing to

qualiﬁed service personnel.

t WARNING: Keep your TV away from moisture. Do not expose your TV to rain or moisture. If water penetrates into

your TV, unplug the power cord and contact your dealer. Continuous use in this case may result in ﬁre or electric

shock.

t Do not use your TV if any abnormality occurs. If any smoke or odor becomes apparent, unplug the power cord

and contact your dealer immediately. Do not try to repair your TV yourself.

t Avoid using dropped or damaged appliances. If your TV is dropped and the housing is damaged, the internal

components may function abnormally. Unplug the power cord immediately and contact your dealer for repair.

Continued use of your TV may cause ﬁre or electric shock.

t Do not install your TV in an area with heavy dust or high humidity. Operating your TV in environments with

heavy dust or high humidity may cause ﬁre or electric shock.

t Follow instructions for moving your TV. Ensure that the power cord and any other cables are unplugged before

moving your TV.

t When unplugging your TV, hold the AC/DC power adapter, not the cord. Pulling on the power cord may damage

the wires inside the cord and cause ﬁre or electric shock. When your TV will not be used for an extended period

of time, unplug the power cord.

t To reduce risk of electric shock, do not touch the connector with wet hands.

t Insert batteries in accordance with instructions. Incorrect polarities may cause the batteries to leak which can

damage the remote control or injure the operator. Do not expose batteries to excessive heat such as sunshine,

ﬁre or the like.

t If any of the following occurs, contact the dealer:

- The power cord fails or frays.

- Liquid sprays or any object drops into your TV.

- Your TV is exposed to rain or other moisture.

- Your TV is dropped or damaged in any way.

- The performance of your TV changes substantially.

t This apparatus shall not be exposed to dripping or splashing and no objects ﬁlled with liquids, such as vases,

shall be placed on the apparatus.

t The mains plug or appliance coupler is used as the disconnect device, the disconnect device shall remain readily

operable.

t CAUTION - These servicing instructions are for use by qualiﬁed service personnel only. To reduce the risk of

electric shock, do not perform any servicing other than that contained in the operating instructions unless you

are qualiﬁed to do so.

t Outdoor Antenna Grounding – If an outside antenna is connected to the receiver, be sure the antenna system is

grounded so as to provide some protection against voltage surges and built up static charges. Section 810 of the

National Electric Code, ANSI/NFPA No. 70-1984, provides information with respect to proper grounding of the

mats and supporting structure grounding of the lead-in wire to an antenna discharge unit, size of grounding

connectors, location of antenna discharge unit, connection to grounding electrodes and requirements for the

grounding electrode. See Figure below.

EXAMPLE OF ANTENNA GROUNDING AS PER NATIONAL ELECTRICAL CODE

Note to the CATV system installer: This reminder is provided to call the CATV system installer’s attention to Article

820-40 of the NEC that provides guidelines for proper grounding and, in particular, speciﬁes that the cable

ground shall be connected to the 6 English grounding system of the building, as close to the point of cable entry

as practical. Please, make sure to connect the power plug to the wall outlet socket after connecting the TV to the

adapter!

ANTENNA

ANTENNA DISCHARGE UNIT

GROUNDING CONDUCTORS

POWER SERVICE GROUNDING ELECTRODE SYSTEM

GROUND CLAMPS

ELECTRIC SERVICE EQUIPMENT

GROUND CLAMP

English

SAVE THESE INSTRUCTIONS

Thank you for purchasing this Haier product. This easy-to-use manual will guide you in

getting the best use of your product. Remember to record the model and serial number.

They are on the label on back of the unit.

Staple your receipt to your manual. You will need it to obtain warranty service

Model number

Serial number

Date of purchase

FOR YOUR SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

PRECAUTIONS AND REMINDERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

PREPARATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

ATTACHING THE STAND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

PREPARING YOUR LCD TV FOR WALL MOUNTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

TURNING ON THE TV. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

PERIPHERAL CONNECTION AND CONTROLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

PERIPHERAL CONNECTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

BUTTON CONTROL

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . 8

MAKING CONNECTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

CONNECTING TO AN ANTENNA/CABLE WALL JACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

CONNECTING EXTERNAL AUDIO/VIDEO DEVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

CONNECTING HEADPHONES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

CONNECTING DIGITAL AUDIO DEVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

OPERATING INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

USING THE REMOTE CONTROL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

INITIAL SETUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

INPUT SOURCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

NAVIGATING THE ON-SCREEN MENU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

PICTURE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

SOUND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

SETTING

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . 13

CHANNEL

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . 13

TIME . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

LOCK

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . 14

Cast TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

TIPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

LEGAL NOTICES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

PRODUCT SPECIFICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

WARNING

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . 21

TABLE OF CONTENTS

English

PREPARATION

IMPORTANT: Do not apply pressure to the screen display

area which may compromise the integrity of the display.

The manufacturer’s warranty does not cover user abuse

or improper installations.

ATTACHING THE STAND

IMPORTANT: The stand of the TV must be assembled

prior to usage.

(blanket, foam, cloth, etc.) to prevent any damage to

the TV.

PREPARING YOUR LCD TV FOR WALL MOUNTING

We suggest that you keep your TV at least 2.36 inches

(60 mm) from the wall to prevent cable interference.

Before mounting your TV on the wall, you need to

remove the stand.

For your safety, please use only with a UL listed wall

mount bracket with minimum weight of the TV without

stand. (Please see page 18 for the weight of the TV.)

To attach a wall mount bracket to your TV:

1. Remove the screws holding your TV to the stand.

2. Remove the stand from your TV.

3. Secure the wall mount bracket to the back of your TV

using four screws (see page 18 for the size of the

screws). Follow the instructions of the user manual

that came with the wall mount bracket to install.

TURNING ON THE TV

1. Install the stand and place the TV on a solid surface.

Ensure that the TV is placed in a position to allow free

back cover.

To prevent any unsafe situations, no naked sources,

such as lighted candles, should be placed on or in the

vicinity.

Avoid heat, direct sunlight and exposure to rain or water.

The equipment shall not be exposed to dripping or

splashing.

2. Connect the antenna cable or cable TV cable to the

ANT IN aerial socket on the back of the TV set. See

"CONNECTING TO AN ANTENNA/CABLE WALL JACK"

on page 9.

3. Remote control:

Remove the cover of the battery compartment.

Insert the 2 supplied batteries (Type AAA 1.5V).

4. Power:

Plug the cord into a working power outlet.

5. Turn the TV on:

Press on the remote control or POWER button on

the side control panel of the TV.

NOTE

The wall mount bracket are not included.

Min

1 m

NOTE

M4x24 mm

(4pcs )

Fix the stand to the bottom of the TV with

the four M4 X 24 mm screws.

PERIPHERAL CONNECTION AND CONTROLS

LORTNOC

BUTTON

NOITCENNOCLAREHPIREP

# Item Description

Optical Out

RJ45

Connect a optical audio cable

Connect the interface of the

network card.

from a sound bar, stereo system,

receiver, etc.

Headphone

Connect headphones to this jack.

Connect the power adaptor .

When headphones are inserted,

the TV speakers will be muted.

Connect an antenna or cable TV

cable to this jack.

USB

Insert the USB storage device into

the USB port to upgrade the

system.

VIDEO

Connect the video cable for a

composite device.

Connect the audio cables for a

co mponent or composite device.

YPbPr

Connect the video cables for a

component device.

HDMI1

HDMI2

HDMI3

Connect HDMI devices to these

jacks. An HDMI cable carries both

video and sound. You do not need

to make an audio connection for

an HDMI device.

HDMI1 HDMI2

(ARC)

Y/VIDEO PbL PrR

OPTICAL OUTRJ45

HDMI3 RF HEADPHONE USB

BACK

On analog and digital TV, the channel

can be switched on and off.

In the absence of audio playback state,

press the volume up / down control.

Open the navigation menu

Navigation menu status

(If this model does not

have the corresponding

function, the icon is grey

and not optional)"

No dispaly in TV

TV Status Middle key Pull Up/Down Pull Left/Right

Navigation menu

Press to open the navigation menu,

press again to close the menu. If there is

no operation, the menu automatically

disappears after 5 seconds.

Press to enter the home page, standby,Press

the corresponding button, the corresponding

icon highlighted, to remind the user has been

operating successfully, and to achieve the

corresponding functions.

Press to enter the menu, input source,Press the

corresponding button, the corresponding icon

highlighted, to remind the user has been

operating successfully, and to achieve the

corresponding functions.

Menu, Home, or

Application status in TV

confirmation key on the remote control.

Short press for confirm,equal to the

return key on the remote control.

Long press to return, equal to the

to the Up/Down key on the remote control.

Achieve up and down buttons function,equal Achieve left and right buttons function,equal

to the Left/Right key on the remote control.

the standby state

Press to power on

Other states

key on the remote control. If the media video

player, can be played and suspended, and

pop-up setting menu.

Press to confirm,equal to the confirmation

to the Pull Up/Down key on the remote control.

Achieve up and down buttons function,equal

Achieve left and right buttons function,equal to the

Left/Right key on the remote control. If it is in the

case of the pop-up media video player setting menu,

achieve fast forward and fast rewind function.

MAKING CONNECTIONS

CONNECTING TO AN ANTENNA/CABLE WALL

JACK

Using component cables (better)

Using composite cable (good)

Cables are often color-coded to match color-coded jacks.

CONNECTING OPTICAL OUT

NOTE

making connections.

English

COMPONENT OUT

L R Y P

OPTICAL

OUT

COMPOSITE OUT

L R VIDEO

CONNECTING EXTERNAL AUDIO/VIDEO DEVICE

Using HDMI cable (best)

To play from the external device:

1. Turn on the TV and the connected device.

2. Press INPUT to open the input source list, then press

to highlight the input to which the device was

connected and press OK to switch.

Select TV to watch TV from the RF input.

Select HDMI1, HDMI2,HDMI3

to play

from a device connected to the HDMI1,

HDMI2,HDMI3

input.

Select Composite to play from the device

connected to the COMPOSITE input.

Select Component to play from the device

connected to the COMPONENT input.

OPERATING INSTRUCTIONS

USING THE REMOTE CONTROL

Item Descriptions

Power

Enter the selected option or perform the

selected operation.

0~9 /

number

Press to enter a TV channel number

(Press "

" to choose the sub-channel).

Chromecast

Press to switch to Chomecast input (Cast TV

mode)

INPUT Press to open the input source list.

Press to open or close the on-screen

Press to play or pause in chromecast mode .

enu.

CH+/CH -

Press CH+ or CH- to change TV channels.

VOL+/VOL-

Press VOL+ or VOL- to adjust volume level.

RECALL Press to switch to last viewed channel.

INFO

BACK Return to the previous menu.

disconnect power, unplug the power cord.

MUTE

PLAY/PAUSE

INITIAL SETUP

will guide you through setting up basic settings.

1. Press to turn on the TV. The setup wizard screen

opens. Press OK to start the wizard.

Press to select your tuner type, then press

to start channel scan.

Air – Set the signal type to antenna. When set to

Air, the TV can receive analog and digital (ATSC)

broadcasting signals.

Cable – Set the signal type to cable. When set to

Cable, the TV can receive analog and QAM

broadcasting signals.

6. The auto channel scan usually takes a few minutes

to complete but can take up to 20 minutes. You can

cancel the channel scan by pressing

EXIT.

During initial setup, press EXIT to exit the initial setup.

INPUT SOURCE

Press INPUT to open the input source list, then press

to highlight an input and press OK to

switch.

NAVIGATING THE ON-SCREEN MENU

1. Press MENU button to display the main menu.

2. Press button to select what you want set.

3. Press OK to enter setting.

Press MENU to return to the previous menu. If the main

menu is displayed, pressing MENU will close the on-

screen menu.

egaugnaLputeSlaitinI

Welcome

uteSlaitinI

Home mode

Store Mode

Welcome

uteSlaitinI

NOTE

2. Press to select Home Mode or Store Mode,

then press to continue.

PICTURE

English

Air

Cable

Auto Volume Level, then press button to choose

Picture Mode – Select the picture mode. You can select:

Standard – A standard picture. The contrast,

brightness, and sharpness are moderately increased.

Vivid – A bright and vivid picture. The contrast,

brightness, and sharpness are

increased.

Mild – A soft picture. The brightness, contrast and

sharpness level are lowered.

User – Customized picture. Picture settings such as

brightness, contrast, and color are manually

adjusted.

Manually adjusting picture settings will automatically

change the Picture Mode to User.

Brightness – Adjust the brightness of the dark areas of

the picture. Press to darken the picture. Press

to brighten the picture.

Contrast – Adjust the brightness of the light areas of

the picture. Press to decrease the contrast. Press

to increase the contrast.

Color – Adjust the color intensity of the picture.

Tint – Adjust the color balance of the picture. Press

to increase the red tones. Press

tones.

to increase

the green

Sharpness – Adjust the color details of picture. Press

to soften the picture. Press to sharpen the

picture.

Color

Aspect Ratio

Temperature

Adjust the overall color of the image.

Press to select Aspect Ratio, press to select.

(Optional:Auto, 16:9, 4:3, Zoom1, Zoom2 ).

Press to select Color Temperature , press to

select.(Optional: Cool, Normal, Warm).

Cool Produces a gentle blue-hued image.

Normal Produces a vivid image.

Warm Produces a red-hued image.

NOTE

SOUND

Sound Mode – Select the sound mode. You can select:

Standard – Balanced treble and bass. This setting is

good for watching standard TV broadcasts.

Music – Increase the treble and bass and preserve

the original sound. This setting is good for listening

to a musical program.

Movie – Moderately decrease and enhance treble

and bass for a rich sound experience.

User – Let you manually adjust sound settings.

Sports– Enhances vocals for sports.

Manually adjusting audio settings will automatically

change the Sound Mode to User.

Balance –

Adjust

Auto Volume Level – Press button to select

the

balance

between

the left and right

audio channels.

Bass – Adjust the low frequency sound. Press to

decrease bass. Press to increase the bass.

Treble

– Adjust the high frequency sound. Press to

decrease treble. Press to increase the treble.

NOTE

Digital Output

– Press button to select digital

Auto – Pass through the original digital audio sound.

PCM – Output audio in 2-channel stereo.

When “ON” is selected, the volume will attempt to stay

at a constant.

output, then press to select.(Options:PCM, Auto, Oﬀ)

ON/OFF.

Energy Saving – The backlight brightness is

decreased to save energy.

Noise Reduction

Setting the option to eliminate image noise intensity.

Press to select Noise Reduction, press to select.

(Optional:Oﬀ, Weak, Middle, Strong, Auto ).

120 Full Motion-Adjust the 120 Full Motion of picture.

You can select Oﬀ On.

, then press button to choose

Surround – Press button to select Surround

ON/OFF.

then press button to select.

(Optional:Default, 1.4, 2.0 )

Active Standby Mode Oﬀ, then press button to

choose

SETTINGS

When in shop mode, the following label will show up.

NOTE

English

CHANNEL

Air/Cable – Select the signal type.

Air – Set the signal type to antenna. When set to Air,

the TV can receive analog and digital (ATSC)

broadcasting signals.

Cable – Set the signal type to cable. When set to

Cable, the TV can receive analog and QAM

broadcasting signals.

Auto Scan – Press OK to start the auto channel scan.

ATV Manual Tuning – Press OK to start the ATV

Closed Caption – Adjust the closed captioning settings.

CC Mode – Select closed captioning mode. You can

select:

CC On – Turn on closed captioning.

CC on Mute – Turn on closed captioning when the

sound is muted.

OSD Language – Select on-screen display OSD

language. You can select English/Français/Español.

Audio Language – Select on-screen display Audio

HDMI EDID –

Press button to select HDMI EDID,

language. You can select English/Français/Español.

Reset TV

TTS

– Reset all settings to the factory defaults.

HDMI CEC

–Press OK button to enter CEC Control

Active Standby Mode – Press button to select

ON/OFF.

then press button to select.

(Optional:Home Mode, Shop Mode )

Usage Mode – Press button to select Usage Mode,

Please refer to the real TV speciﬁc picture

submenu.

Manual Tuning.

DTV Manual Tuning – Press

Programme Edit

– Press button to select

OK to start the DTV

Manual Tuning.

editing programs, press OK to enter the sub-menu.

Audio Only

audio.

TTS – Select On or Oﬀ.

Pitch – Select Mid/High/Low.

Volume – Select Mid/High/Low.

Rate Support – Select Mid/Fast/Slow.

– Press OK button to enter sub-menu

Over Scan – Extend part of the display past the visible

area of the screen. The resulting picture will “zoom in”

on the image center.

Auto Scan ATV Manual Tuning

DTV Manual Tuning

Favorite List -Add and skip channels in your

favorite channel list.

LOCK

1. Press OK to enter password.

2. Use the number buttons on the remote control to

enter your 4-digit password. The default password is

“0000”.

3. After the correct password is entered, the Lock sub-

menu screen opens.

Set Password – Press OK to set a new 4-digit password.

Enter Old Password – Enter your old 4-digit

password.

Enter New Password – Enter your new 4-digit

password.

Password – Enter your new 4-digit password

System Lock – Turn the US and Canada rating limits on

Input Block

US Rating – Set the U.S. rating limits.

TV – U.S. TV ratings. The TV ratings compose of two

aspects: age-based and content-based.

Time – Adjust the time settings.

Sleep Timer

then press button to select.

(Optional:oﬀ, 10min, 20min, 30min, 60min,

120min, 180min, 240min )

TIME

Programme Edit

– Press button to select

Sleep Timer ,

OSD Timer

then press button to select.

(Optional:oﬀ, 5s, 10s, 15s, 20s )

– Press button to select

OSD Timer ,

Signal Information

– Press button to select

editing programs, press OK to enter the sub-menu.

– Press button to select Input Block

, press OK to enter the sub-menu.

English

TV rating levels

MPAA

comes from MPAA rules.

MPAA rating levels

Canada Rating – Set the Canada rating limits.

Canada English – The ratings are for programs using

the English rating system.

Canada English rating levels

Canada French – The ratings are for programs using

the French rating system.

Canada French rating levels

When a rating is locked, that rating and all other higher

ratings are locked. When a rating is unlocked, that rating

and all lower ratings are unlocked.

RRT Setting – Adjust RRT settings.

Reset RRT – Reset RRT settings to the factory default.

U.S TV ratings (content-based)

ALL All ratings

FV Fantasy violence

V Violence

S Sexual situations

L Strong language

D Suggestive dialog

U.S TV ratings (age-based)

TV-Y All children.

TV-Y7 Suitable for children 7 and older.

TV-G General audiences.

TV-PG Parental guidance suggested.

TV-14

Parental guidance strongly

suggested.

TV-MA Mature audiences onl

TV-NONE ALL ages.

NR Not rated.

U.S movie (MPAA) ratings

G General audiences.

PG Parental guidance suggested.

PG-13 Suitable for children 13 and older.

Parental guidance suggested for

children under 17.

NC-17 Not suitable for children under 17.

X Adults only.

Canadian English ratings

C Suitable for all children.

C8+ Suitable for children 8 and older.

G General audiences.

PG Parental guidance suggested.

14+ Suitable for children 14 and older.

18+ Adults only.

Canadian French ratings

G General audiences.

8 ans+ Suitable for children 8 and older.

13 ans+ Suitable for children 13 and older.

16 ans+ Suitable for children 16 and older.

18 ans+ Adults only.

NOTE

1. Open GoogleHome on your mobile device and ﬁnd

the device .

The version of the Android device uses Android 5.1 or

above as much as possible. Ios device Make sure Bluetooth

is on before connecting to Cast.

The above shows the use of IOS phone for mobile devices,

Android device interface and operating procedures will be

slightly diﬀerent.

Mobile can not ﬁnd CAST TV in GoogleHome

Possible reasons are as follows:

1. If it is IOS phone, may be the phone Bluetooth is not

open, please open the phone Bluetooth, re-view the device

list.

2. TV board connected to the wired network, and wired

network with the mobile phone WIFI connected to the

network is not a network, so the phone can not ﬁnd this

TV device. Please unplug the cable network and restart the

TV device, so that the phone through the WIFI to TV

equipment.

3. TV Wiﬁ module is not working properly or antenna

signal is weak.

NOTE

Cast TV

TV sideMobile terminal

2. Select the device, follow the prompts to continue,

when the Mobile terminal and TV display as shown in the

state when the phone connected TV success. Please

conﬁrm the veriﬁcation code.There will be a process of

rotation waiting in the process, please be patient.

3. Choose a location for Chomecast bulit-in TV. This

will help you organize your devices.

4. Choose a Wi-Fi network to use to set up Chomecast

bulit-in TV.

TV sideMobile terminal TV sideMobile terminal

TV side

Mobile terminal

5. Chromecast buile-in TV is ready.

6. Open the App's Cast icon, and then select the Cast

TV, the connection is successful, click to play the video,

the TV will be able to load the normal playback.

TV sideMobile terminal

English

TIPS

Care of the screen

Do not rub or strike the screen with anything hard as

this may scratch, mar, or damage the screen

permanently.

Unplug the power cord before cleaning the screen. Dust

the TV by wiping the screen and the cabinet with a soft,

clean cloth. If the screen requires additional cleaning,

use a clean, damp cloth. Do not use liquid cleaners or

aerosol cleaners.

Mobile telephone warning

To avoid disturbances in picture and sound,

malfunctioning of your TV or even damage to the TV,

keep your mobile telephone away from the TV.

End of life directives

We are paying a lot of attention to produce

environmentally friendly products. Your new television

contains materials, which can be recycled and reused.

At the end of its life, specialized companies can

dismantle the discarded receiver to collect the

reusable materials and to minimize the amount of

materials to be disposed of.

Please ensure you dispose of your old receiver

according to local regulations. Haier is committed to

safely recycling electronic products and product

materials. Please check for a local recycling location in

the United States at: 1800RECYCLING.COM.

LEGAL NOTICES

Modications

The FCC requires the user to be notiﬁed that any

changes or modiﬁcations made to this device that are

not expressly approved by our company may void the

user’s authority to operate the equipment.

Cables

Connections to this device must be made with shielded

cables with metallic RF/EMI connector hoods to

maintain compliance with FCC Rules and Regulations.

Canada ICES-003 statement

This Class B digital apparatus complies with Canadian

ICES-003. Standard Television Receiving Apparatus —

Appareil de réception télévision ordinaire, Canada BETS-

7/NTMR-7.

Canadian notice

This Class B digital apparatus meets all requirements of

the Canadian Interference-Causing Equipment

Regulations.

Avis Canadian

Cat apparel numerous de la classed B respected toutes

les exigencies du règlement sur le materiel brouilleur du

Canada.

HDMI, the HDMI logo, and High-Deﬁnition Multimedia

Interface are trademarks or registered trademarks of

HDMI Licensing LCC in the United States and other

countries.

Never place a television set in an unstable location. A television set may fall, causing

serious

personal injury or death. Many injuries, particularly to children, can be avoided by taking

simple precautions such as:

a) --Using cabinets or stands recommended by the manufacturer of the television set.

b) – Only using furniture that can safely support the

television set.

c) – Ensuring the television set is not overhanging the edge of the suppprting

furniture.

d) – Not placing the television set on tall furn

iture (for example, cupboards or

bookcases) without anchoring both the furniture and the television set to a suitable

support.

e) – Not placing the television set on cloth or other materials

that may be located between the television set and supporting funiture.

f) – Educating children about the dangers of climbing on

funiture to reach the television set or its controls.

If your existing television set is being retained and relocated, the same considerations as

above should be applied.

WARNING

PRODUCT SPECIFICATION

NOTE

Model 50UG6550G

DISPLAY

50”(127cm)

elbaweiV

Television System NTSC, ATSC

Channel Coverage NTSC: CH2-CH69 (Antenna)/CH1-CH135 (Cable)

ATSC: CH2-CH69 (Antenna)/CH1-CH135 (Cable)

CONNECTIONS

srotcennoCraeR

VIDEO/Y

HDMI3

(3840*2160@60FPS)

HDMI1/2(3840*2160@60FPS)

Headphone

OPTICAL OUT

RJ45

srotcennoCediS

USB

44.15” x 27.71” x 9.6”

44.15” x 25.58” x 2.36”

WEIGHT & DIMENSION

Dimensions with Stand (W x H x D)

Dimensions without Stand (W x H x D)

Weight with Stand 26.24 lbs

Weight without Stand

25.79 lbs

WALL MOUNTING

Wall Mount Pattern (H x V) 200 x 200 mm

M8 x 8mm epytwercS

POWER

Power Consumption

140W

0.50W≤ybdnatS

120V~60HzrewoPsniaM

10W+10WrewoPoiduA

Ambient Temperature 41°F ~ 95°F

PACKAGE CONTENTS

Package Contents

TV unit x 1

TV stand x 2

Remote control x 1

Stand screws x 4

User manual x 1

Registration card x 1

Battery x 2

La page charge ...

Haier 50UG6550G Manuel utilisateur

Marque: Haier

Modèle: 50UG6550G

Catégorie: Téléviseurs LED

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Haier 50UG6550G User manual
español: Haier 50UG6550G Manual de usuario

Haier 50UG6550G Manuel utilisateur

Haier 50UG6550G Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents