Maytag BRAVOS MTW6600TQ0 Manuel utilisateur

Marque: Maytag

Modèle: BRAVOS MTW6600TQ0

Catégorie: Machines à laver

Taper: Manuel utilisateur

Ce manuel convient également à

BRAVOS MTW6600TB0

BRAVOS TMAUTOMATIC WASHER

USE & CARE GUIDE

LAVADORA AUTOMATICA BRAVOS TM

MANUAL DE USO Y CUIDADO

LAVEUSE AUTOMATIQUE BRAVOS TM

GUIDE D'UTILISATION ET D'ENTRETIEN

FOR QUESTIONS ABOUT FEATURES, OPERATION/PERFORMANCE,

PARTS, ACCESSORIES OR SERVICE CALL: 1.800.688.9900

IN CANADA, CALL: 1.800.807.6777

VISIT OUR WEBSITE AT WWW.MAYTAG.COM

IN CANADA, WWW.MAYTAG.CA

W10092685A

SI TIENE PREGUNTAS RESPECTO A LAS CARACTERiSTICA8,

FUNCIONAMIENTO, RENDIMIENTO, PARTES, ACCESORIOS O

SERVICIO TECNICO, LLAME AL: 1.800.688.9900

EN CANADa,, LLAME AL: 1.800.807.6777

VISITE NUESTR(-) SITIO WEB EN

WWW.MAYTAG.C(-)M

EN CANADA, WWW.MAYTAG.CA

AU CANADA, POUR ASSISTANCE, INSTALLATION OU SERVICE,

COMPOSER LE : 1.800.807.6777

OU VISITEZ NOTRE SITE INTERNET _,

WWW.MAYTAG.CA

_I_1_i!!i_i_:_iiiiiii_ii_¢:_:_!!_!:',iiiiiiiiiiiiii,'_t_:i!:_:_i!:!iii!!i_iiii_!_i_i_!!!!!!!!!!i_:iiiiiiiiiiiiiiiiiiiiiiiiii_¸¸¸¸¸¸¸¸¸¸¸

TABLE OF CONTENTS

WASHER SAFETY .................................................................. 3

INSTALLATION REQUIREMENTS ......................................... 4

Tools and Parts ................................................................... 4

location Requirements ....................................................... 5

Drain System ...................................................................... 6

Electrical Requirements ...................................................... 6

INSTALLATION INSTRUCTIONS ......................................... 7

Before You Start ................................................................. 7

Remove Shipping Base and Packing Ring .......................... 8

Connect [_brain Hose .......................................................... 8

Connect the Inlet Hoses ..................................................... 9

Secure the Drain Hose ..................................................... 10

level the Washer .............................................................. 11

Complete Installation ....................................................... 12

BENEFITS AND FEATURES .................................................. 12

Benefits ............................................................................ 12

Features ............................................................................ 13

WASHER USE ...................................................................... 14

Starting Your Washer ....................................................... 14

Using the Proper Detergent .............................................. 14

Pausing or Restarting the Washer ..................................... 15

Stopping the Washer ........................................................ 16

Changing Cycles, Modifiers and Options ......................... 16

Status Lights ...................................................................... 16

Cycles .............................................................................. 16

Modifiers .......................................................................... 18

Options ............................................................................ 19

Operating Controls ........................................................... 19

Normal Sounds ................................................................ 20

LAUNDRY TIPS ................................................................... 20

WASHER CARE .................................................................... 21

Cleaning Your Washer ..................................................... 21

Water Inlet Hoses ............................................................. 21

Vacation, Storage and Moving Care ................................. 21

TROUBLESHOOTING ......................................................... 22

Washer and Components ................................................. 22

Washer Operation ............................................................ 24

Clothing Care ................................................................... 25

ASSISTANCE OR SERVICE ................................................... 27

WARRANTY ..................................................................... 28

?i;_i_!!_iiiiiiiiiiiiiiiiiii_!!!ii!_!iii!!i!!!!!iiii!!_i!ii!i_!i:_i_iiiiii!i!ii!!_!!_iiiiiiiiii__ii!i_i!ii_!!!!!!_!_i_i!_!!iiiiiii_!!iiiiiiiiiiiiiiiiiiiiiii_;iii:ii!!i!i¸¸¸

INDICE

SEGURIDAD DE LA LAVADORA ....................................... 29

REQUISITOS DE INSTALACION ........................................ 30

Piezas y herrarnientas ...................................................... 30

Requisitos de ubicaci6n ................................................... 31

Sistema de desagOe ......................................................... 32

Requisitos el6ctricos ........................................................ 33

INSTRUCCIONES DE INSTALAClON ................................ 34

Antes de comenzar .......................................................... 34

Quite la base y el anillo de embalaje .............................. 34

Conecte la manguera de desagL_e .................................... 34

Conexi6n de las mangueras de entrada ........................... 35

Fijaci6n de la manguera de desagOe ................................ 36

Nivelaci6n de la lavadora ................................................ 37

Complete la instalaci6n ................................................... 38

BENEFIClOS Y CAI_CTERiSTICAS .................................... 38

Beneficios ........................................................................ _¢8

Caracter[sticas ................................................................. 39

USO DE LA LAVADORA .................................................... 40

Puesta en marcha de la lavadora ..................................... 40

Uso del detergente adecuado .......................................... 40

Pausa o reanudaci6n de la marcha de la lavadora .......... 41

C6mo detener la lavadora ............................................... 42

Cambio de ciclos, modificadores y opciones .................. 42

I.uces de estado ............................................................... 42

Ciclos .............................................................................. 42

Modificadores .................................................................. 44

Opciones ......................................................................... 45

Controles de funcionamiento .......................................... 46

Sonidos normales ............................................................ 46

CONSEJOS DE LAVANDERiA ............................................ 47

CUIDADO DE LA LAVADORA .......................................... 47

C6mo limpiar su lavadora ............................................... 47

Mangueras de entrada de agua ........................................ 48

Cuidado durante las vacaciones, el almacenamiento

y las mudanzas ................................................................ 48

SOLUCION DE PROBLEMAS ............................................. 49

Lavadora y componentes ................................................. 49

Funcionamiento de la lavadora ....................................... 51

Cuidado de la ropa .......................................................... 52

AYUDA O SERVICIO Ti_CNICO ......................................... 54

GARANTIA ....................................................................... 55

_:!_i!i!_iii!ii_!!!!!!!!!!!!!!!!ii_i_ii::iiiiiiiiiiiiii_!i_iiiii_i_!!!iiiiiiii_!!!!!!!i_iiiiiiiiii_i_i_i;_:_:_iii:!;_i_¸:¸¸¸:

TABLE DES MATIERES

S[_CURIT[_ DE LA LAVEUSE ................................................. 56

EXIGENCES D'INSTALLATION ........................................... 57

Outillage et pi_ces ........................................................... 57

Exigences d'emplacement ................................................ 58

Syst6me de vidange ......................................................... 59

Sp6cifications _lectriques ................................................. 59

INSTRUCTIONS D'INSTALLATION ................................... 60

Avant de commencer ....................................................... 60

Retrait de la base d'exp6dition et de I'anneau

d'emballage ..................................................................... 61

Raccordement du tuyau de vidange ................................. 61

Raccordement des tuyaux d'alimentation ........................ 62

Immobilisation du tuyau de vidange ................................ 63

R6glage de I'aplomb de la laveuse ................................... 64

Achever I'installation ....................................................... 65

AVANTAGES ET CARACTI_RISTIQUES ............................... 65

Avantages ........................................................................ 65

Caract6ristiques ................................................................ 66

UTILISATION DE LA LAVEUSE ........................................... 67

Mise en marche de la laveuse .......................................... 67

Utilisation du d(!tergent appropri(! ................................... 67

Pause ou remise en marche de la laveuse ........................ 69

Arr_t de la laveuse ........................................................... 69

Changement des programmes, modificateurs

et options ......................................................................... 69

T(!moins lumineux ........................................................... 69

Programmes ..................................................................... 70

Modificateurs ................................................................... 72

Options ............................................................................ 7_¢

Fonctionnement des commandes .................................... 74

Sons normaux .................................................................. 74

CONSEILS DE LESSIVAGE ................................................... 74

ENTRETIEN DE LA LAVEUSE .............................................. 75

Nettoyage de la laveuse ................................................... 75

Tuyaux d'arriv6e d'eau .................................................... 75

Pr(!cautions _ prendre avant les vacances, un

entreposage ou un d(!m_nagement .................................. 75

DEPANNAGE ...................................................................... 77

I.a laveuse et ses composants ........................................... 77

Fonctionnement de la laveuse ......................................... 79

Soin des v&tements .......................................................... 80

ASSISTANCE OU SERVICE .................................................. 82

GARANTIE .......................................................................... 83

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

7<7,1

!711111111711!iT!_7!iii!iii!iiiiiiiiiiiiiiiiiiiiiiiiii!!;_%Tili _i_ii_ill¸¸ 3

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury to persons when using the washer follow basic precautions,

including the following:

• Read all instructions before using the washer.

• Do not wash articles that have been previously cleaned

in, washed in, soaked in, or spotted with gasoline,

dry-cleaning solvents, other flammable, or explosive

substances as they give off vapors that could ignite or

explode.

• Do not add gasoline, dry-cleaning solvents, or other

flammable, or explosive substances to the wash water.

These substances give off vapors that could ignite or

explode.

• Under certain conditions, hydrogen gas may be

produced in a hot water system that has not been used

for 2 weeks or more. HYDROGEN GAS IS

EXPLOSIVE. If the hot water system has not been

used for such a period, before using the washing

machine, turn on all hot water faucets and let the water

flow from each for several minutes. This will release

any accumulated hydrogen gas. As the gas is

flammable, do not smoke or use an open flame during

• Do not allow children to play on or in the washer. Close

supervision of children is necessary when the washer is used

near children.

• Before the washer is removed from service or discarded,

remove the door or lid.

• Do not reach into the washer if the drum, tub or agitator is

moving.

• Do not install or store the washer where it will be exposed to

the weather.

• Do not tamper with controls.

• Do not repair or replace any part of the washer or attempt any

servicing unless specifically recommended in this manual or in

published user-repair instructions that you understand and

have the skills to carry out.

• See "Electrical Requirements" for grounding instructions.

this time.

SAVE THESE INSTRUCTIONS

INSTALLATION REQUIREMENTS

Cather the required tools and parts before starting installation. The parts supplied are in the

washer basket.

Tools needed for connecting the drain hose and water inlet hoses:

• Pliers that open to 1%0" (3.95 crn) • Flashlight (optional)

NOTE: Replace inlet hoses after 5 years of use to reduce the risk of hose failure. Record hose

installation or replacement dates for future reference.

Parts supplied:

B C

A. Drain hose form

B. Water inlet hoses (2)

C. flat water inlet hose washers (4)

D. Beaded tie strap

Tools needed for securing the drain hose and leveling the washer:

• Adjustable or open end • Wood block

wrench %6" (14 ram)

• Ruler or measuring tape

• level

Alternate Parts

Your installation may require additional parts. If you are interested in purchasing one of the

items listed here, call the toll-free number on the cover or in the "Assistance or Service"

section.

If You Have: You Will Need to Buy:

Laundry tub or standpipe taller Sump pump system (if not already available)

than 96" (2.4 m)

I" (2.5 cm) diameter standpipe 2" (5 cm) diameter to 1" (2.5 cm) diameter standpipe

adapter, Part Number 336%920 and connector kit Part

Number 2858%5

Overhead sewer Standard 20 gal. (76 I) 39' (99 cm) tall drain tub or

utility sink, sump pump and connectors (available from

local plumbing suppliers)

Floor drain Siphon break, Part Number 285834; additional drain

hose, Part Number 8318155 and connector kit,

Part Number 2858%5

Selecting the proper location for your washer improves performance and minimizes noise and

possible washer "walk."

Your washer can be installed in a basement laundry room, closet, or recessed area. See

"Drain System."

IMPORTANT: Do not install or store the washer where it will be exposed to the weather.

Proper installation is your responsibility.

You will need:

• A water heater set to deliver 120°F (49°C) water to the washer.

• A grounded electrical outlet located within 4 ft (1.2 m) of where the power cord is

attached to the back of the washer. See "Electrical Requirements."

• Hot and cold water faucets located within 3 ft (90 cm) of the hot and cold water fill

valves, and water pressure of 20-100 psi (138-690 kPa) for best performance.

H F-

• A level floor with a maximum slope of 1 /2.a cm) under entire washer. Installing the

washer on carpeting is not recommended.

• A sturdy floor to support the washer weight (washer, water and load) of 315 Ibs (143 kgs).

Do not store or operate your washer in temperatures at or below 32°F (0°C). Some water can

remain in the washer and can cause damage in low temperatures. See "Washer Care" for

winterizing information.

Installation spacing for recessed area and closet installations

The following spacing dimensions are recommended for this washer. This washer has been

tested for installation with spacing of 0" (0 cm) clearance on the sides. Recommended

spacing should be considered for the following reasons:

• Additional spacing should be considered for ease of installation and servicing.

• Additional spacing should be considered on all sides of the washer to reduce noise

transfer.

Water faucets beyond reach of 2 longer water fill hoses:

fill hoses 6 fl (I .8 m) Part Number 76314,

I0 ft (3.0 m) Part Number 350008

lint clogged drain Drain protector, Part Number 367031

• For closet installation with a door, minimum ventilation openings in the top and bottom of

the door are required. ] ouvered doors with equivalent ventilation openings are

acceptable.

• Companion appliance spacing should also be considered.

17,,,_-

(43.2c__

olo

(3100m't-

.2,

24in.2 _ .__

._ (155cm)

1'_,,_ <--27/2'_ _1" -_ 1'1,-27" --_ 5"*1_-

(2.5 cm) (69.9 cm) 2.5 cm (2.5 crn) (68.6 cm) (12.7 crn)

A B C

3"*

q7.6cm)

__ 3"*

(7.6cm)

A. Front view

B. Side view

C. Closet door with vents

* Required spacing

The washer can be installed using the standpipe drain system (floor or wall), the laundry tub

drain system, or the floor drain system. Select the drain hose installation method you need.

See "Fools and Parts."

Standpipe drain system--wall or floor (views A & B)

The standpipe drain requires a minimum diameter standpipe of 2" (5 cm). The minimum

carry-away capacity can be no less than 17 gal. (G4 1.) per minute. A 2" (5 cm) diameter to

1" (2.5 cm) diameter standpipe adapter kit is available. See "]ools and Parts."

The top of the standpipe must be at least 39" (99 cm) high and no higher than 96" (244 cm/

from the bottom of the washer.

39"

(99 cm)

Laundry tub drain system (view C)

The laundry tub needs a minimum 20 gah (76 I.) capacity. The top of the laundry tub must be

at least _¢9" (99 cm) above the floor and no higher than 96" (244 cm) from the bottom of the

washer.

Floor drain system (view D)

[he floor drain system requires a siphon break that may be purchased separately. See "[bols

and Parts."

[he siphon break must be a minimum of 28" (71 cm) from the bottom of the washer.

Additional hoses might be needed.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

A 120 volt, 60 Hz., AC only, 15- or 20-amp, fused electrical supply is required. A time-

delay fuse or circuit breaker is recommended. It is recommended that a separate circuit

serving only this appliance be provided.

• This washer is equipped with a power supply cord having a 3 prong grounding plug.

• [b minimize possible shock hazard, the cord must be plugged into a mating, 3 prong,

grounding-type outlet, grounded in accordance with local codes and ordinances. [f a

mating outlet is not available, it is the personal responsibility and obligation of the

customer to have the properly grounded outlet installed by a qualified electrician.

• If codes permit and a separate ground wire is used, it is recommended that a qualified

electrician determine that the ground path is adequate.

• Do not ground to a gas pipe.

• Check with a qualified electrician if you are not sure the washer is properly grounded.

• Do not have a fuse in the neutral or ground circuit.

GROUNDING INSTRUCTIONS

For a grounded, cord=connected washer:

This washer must be grounded. In the event of a malfunction

or breakdown, grounding will reduce the risk of electrical

shock by providing a path of least resistance for electric

current. This washer is equipped with a cord having an

equipment-grounding conductor and a grounding plug. The

plug must be plugged into an appropriate outlet that is

properly installed and grounded in accordance with all local

codes and ordinances.

WARNING: Improper connection of the equipment-

grounding conductor can result in a risk of electric shock.

Check with a qualified electrician or serviceman if you are in

doubt as to whether the appliance is properly grounded.

Do not modify the plug provided with the appliance - if it will

not fit the outlet, have a proper outlet installed by a qualified

electrician.

For a permanently connected washer:

This washer must be connected to a grounded metal,

permanent wiring system, or an equipment grounding

conductor must be run with the circuit conductors and

connected to the equipment-grounding terminal or lead on

the appliance.

Excessive Weight Hazard

Use two or more people to move and install washer.

Failure to do so can result in back or other injury.

NOTE: lo avoid floor damage during installation, set the washer onto cardboard before

moving across floor.

IMPORTANT:

• Be sure the foam shipping base has been removed from the bottom of the washer as

directed in the Unpacking Instructions.

• If foam shipping base has not been removed, be sure lid is secured with tape before laying

washer on its back.

• Removing the foam shipping base is necessary for proper operation.

!_iiiilZ:i!iiii_:!!ii!iii!iii!iiiiiiiiiiiiiiiiiiiiiiiiii!!:_%iiiiiiii i_i!iiiiiiiiiill¸¸ 7

1. Place cardboard supports from shipping carton on floor behind washer for support.

2. Secure the lid with tape.

3. Using 2 or more people, tip the washer onto its back and place on cardboard supports,

4. Remove foam shipping base.

5. Set washer upright.

6. Remove tape from lid. Open lid and remove foam packing ring from washer tub. Keep

foam packing ring ill case you need to move the washer in the future.

Proper connection of the drain hose protects your floors from damage due to water leakage,

Read and follow these instructions.

[he drain hose is connected to your washer and is stored inside the washer cabinet,

Remove drain bose from washer cabinet

Pull the corrugated drain hose out of the washer by first grabbing the pull tie. Continue to pull

the hose until the end emerges. Do not force excess drain hose back into the rear of the

washer.

Laundry tub drain or standpipe drain

Connecting the drain hose form to the corrugated drain hose

4.5"

(11.4 cm)

A. Drain hose mlMf_

1.F_'edend o[ drain hose into one end of form. Place end of drain hose

form into the drain hose relief.

2. Bend the hose over the top of the form and fe'ed into the other end of

the form. Attach the other end of the form into the other drain hose

relief. The hose must extend 4_//" ( 11.4 crn) beyond the form.

To keep drain water from going back into the washer:

• Do not force excess drain hose into standpipe. Hose should be secure but loose enough

to provide a gap for air.

• Do not lay excess hose on the bottom of the laundry tub.

Floor drain

Do not install the drain hose form on to the corrugated drain hose. You may need additional

parts. See Floor drain under "Fools and Parts."

ll e "

Insert new flat washers (supplied) into each end of the inlet hoses. Firmly seat the washers

in the couplings.

A B

A. Coupling

B. Washer

Connect the inlet hoses to the water faucets

Make sure the washer basket is empty.

2. Attach the hose labeled hot to the hot water faucet. Screw on coupling by hand until it is

seated on the washer.

3. Attach the hose labeled cold to the cold water faucet. Screw on coupling by hand until it

is seated on the washer.

4. Using pliers, tighten the couplings with an additional two-thirds turn.

light_ul the couplings with an additional two-thirds turll.

NOTE: Do not overtighten or use tape or sealants on the valve. [Damage to the valves can

result.

Clear the water lines

• Run water through both faucets and inlet hoses, into a laundry tub, drainpipe or bucket,

to get rid of particles in the water lines that might clog the inlet valve screens.

• Check the temperature of the water to make sure that the hot water hose is connected to

the hot water faucet and that the cold water hose is connected to the cold water faucet.

Connect the inlet hoses to the washer

COLD

A. Hot water inlet valve

B. Cbld water inlet valve

1. Attach the hot water hose to the inlet valve labeled hot.

2. Attaching one hose coupling first makes it easier to tighten the connection with pliers.

3. Screw on coupling by hand until it is seated on the washer.

4. Using pliers, tighten the coupling with an additional two-thirds turn.

NOTE: Do not overtighten or use tape or sealants on the valve. Damage to the valves can

result.

Check for leaks

• Turn on the water faucets and check for leaks. A small amount of water might enter the

washer. You will drain this in a later step.

NOTE: Replace inlet hoses after 5 years of use to reduce the risk of hose failure. Record

hose installation or replacement dates for future reference.

• If you connect only one water hose, you must cap off the remaining water inlet port.

• Periodically inspect and replace hoses if bulges, kinks, cuts, wear, or leaks are found.

1. Drape the power cord over the console.

2. Remove any cardboard used to move washer.

Zg>

Beaded de strap

3. Fasten the drain hose to the laundry tub leg or drain standpipe with the beaded tie strap.

See view A or B.

If the washer faucets and the drain standpipe are recessed, put the formed end of the drain

hose into the standpipe. Tightly wrap the tie strap around the water inlet hoses and the

drain hose. See view C.

5. Attach the cold water hose to the inlet valve labeled cold.

6. Screw on coupling by hand until it is seated on the washer.

7. Using pliers, tighten the coupling with an additional two-thirds turn.

NOTE: Do not overtighten or use tape or sealants on the valve. Damage to the valves can

result.

Excessive Weight Hazard

Use two or more people to move and install washer.

Failure to do so can result in back or other injury.

One washer foot has been installed at a different height on your new washer. The other three

feet were preset at the factory. Properly leveling your washer will minimize noise and

vibration.

1. Slide the washer to its final location.

2. Push on upper front panel to be sure the washer is on its rear feet.

4. Check the levelness of the washer by first placing a level oil the lid near the console.

Next, place the level on the side of the washer in the crease between the top of the

washer and the cabinet.

Level the front.

lower right front foot until it contacts tile floor. By hand, firmly rotate foot as much as an

additional 1V2 turns. The other three feet have been preset at the factory.

[ew_l the side.

5. If the washer is not level, move the washer out slightly, tip back, prop up the front of the

washer on a wood block. Adjust the feet up or down as necessary by twisting the feet.

Repeat steps 1 through 4 until washer is level.

6. Use a 9/16"or 14 mm open-end wrench to turn the Iocknut counterclockwise on the foot

tightly against the washer cabinet.

IMPORTANT." if the Iocknut is not tight against the washer cabinet, the washer may

vibrate.

1. Check the electrical requirements, Be sure that you have the correct electrical supply and

the recommended grounding method. See "Electrical Requirements."

2. Check that all parts are now installed. If there is an extra part, go back through the steps to

see which step was skipped.

3. Check that you have all of your tools.

4. Keep the foam packing ring from the washer tub for future relocation of the washer.

Dispose of/recycle all packaging materials.

5. Check that the water faucets are on.

6. Check for leaks around faucets and inlet hoses.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord,

Failure to follow these instructions can result in death_

fire_ or electrical shock.

7, Plug into a grounded 3 prong outlet.

8, Remove any protective film or tape remaining on the washer.

9, Read "Washer Use."

10. [.o test and to clean your washer, measure//2 of the detergent manufacturer's

recommended amount of High Efficiency (HE) powdered or liquid detergent for a

medium-size load and pour it into the detergent dispenser. Close the lid. Press POWER.

Select a normal cycle and press Start. Allow it to complete one whole cycle.

;i_!;_!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!;[ii_!_!iiii_!iiii_!iiii_!iiii_!!_!_!_!I_!_!_!_!!i!i!_iii_!_i_!_!_!_!_!_¸ 4_ _g_@_;_s_g_(_(_}_}_U_;_;;; _¸¸

BENEFITS AND FEATURES

Your washer has several benefits and features which are summarized here. Some items may

not apply to your model.

High-Efficiency Wash System

Your new top loading, high-efficiency washer saves you time by allowing you to do fewer,

larger loads. [t also conserves resources and also lowers your water and energy bills by using

the following innovations.

IntelliFill _mWater Level Control

This washer senses the load size and composition through a series of fills and wash motion. It

then adjusts the water level for the best cleaning and rinsing performance. It eliminates the

guesswork. ]he water level is just right for every wash load size.

NOTE: You may notice during a cycle that the wash load is not completely submerged in

water. [-his is normal for your washer.

Auto Temp Control

The Auto Temp Control system on this washer electronically senses and maintains a uniform

water temperature by regulating incoming water temperatures. Using Auto Temp Control will

hel I) dissolve detergent.

Washer Impeller System

Your new washer works differently than most washers that you are accustomed to. The most

striking difference is that the washer has a washer impeller system. [t uses this new innovative

washer impeller at the bottom of the wash basket to move your load through a mixture of

water and detergent. The load is moved from the outside toward the middle with items

coming up in the center and down on the outside edges.

Dispensers

The dispensers make your washer truly automatic. It is unnecessary for you to return to the

washer during the cycle to add detergent, bleach, or fabric softener.

laundry products are added to the load at the proper time in the wash cycle.

Spin Speeds

This washer is [)reset to automatically select the spin speed based on the cycle selected.

Depending on your wash load, you can change the preset speeds. ]he spin speed on this

washer is nearly twice as fast as that of a conventional washer. You may notice different

sounds during a spin cycle because of this higher speed.

Stain Cycle

The Stain Cycle option uses E)irect Inject Cleaning Action to help ensure better soil and stain

removal. Stain Cycle reduces the need for pretreatment and is safe for all washable fabrics.

Water flushes through the dispenser to dissolve the detergent. [he detergent mixture is then

sprayed onto the load while the washer spins at low speed. This cleaning action will last up to

5 minutes depending on the cycle selected.

The washer then stops spinning, fills with water to the appropriate level and continues

washing with the selected cycle.

High Efficiency (HE) Detergent

This washer is designed for High Efficiency (HE) detergent use only. HE detergents are made to

produce the right amount of suds and give the best performance in low water wash systems.

Innovative Features

Your new washer includes these features that help to reduce noise, increase the ease of use

and improve wash performance.

Electronic Controls

Electronic controls with preset cycles are easy to use whether you are a beginner or an

"expert."

Quiet Operation

This washer is insulated with sound-dampening materials to reduce washer operation sounds

and noises. On some models, an additional tub wrap is added for extra dampening of

vibration and sound. The washer has an additional bottom sound pad that is included

separately for installation by the customer.

Suspension System

[b reduce washer "walk" and "out of balance" conditions, your new washer combines:

• 4 Spring damper struts to isolate vibration

• Balance ring at the top and bottom of the wash basket to minimize vibration

• Operating software designed to sense and correct off-balance loads

Clean Washer Cycle

This washer features an easy-to-use Clean Washer cycle that thoroughly cleans tile inside of

your washing machine using higher water volumes in combination with liquid chlorine

bleach.

Stainless Steel Basket

The stainless steel basket is corrosion resistant and enables higher spin speeds for more water

extraction, reducing drying time.

Self-clean Wash and Rinse Filter System

This washer filters 100% of the wash and rinse water. The water is filtered then recirculated.

[he force filter traps sand and dirt, flushing them down the drain, so they are not redeposited

onto the clean clothes.

Delay Wash

Delay Wash allows you to load your washer and pause tile start of tile cycle for up to

10 hours.

Endof Cycle Signal

The End of Cycle Signal produces an audible sound when the wash cycle is finished. This

signal is helpful when you are removing items from the washer as soon as it stops.

WASHER USE

POWER

WHITESJ

WASH CYCLES

NOTE: Your washer model may vary from the model shown.

_!,lilIl=llI]l! !f_t _"" ' " "=......

Fire Hazard

Never place items in the washer that are dampened

with gasoline or other flammable fluids.

No washer can completely remove oil.

Do not dry anything that has ever had any type of oil on

it (including cooking oils).

Doing so can result in death, explosion, or fire.

WARNING: [b reduce the risk of fire, electric shock, or injury to persons, read the

IMPORTANT SAFETY INSTRUCTIONS before operating this appliance.

The following is a guide to starting your washer. Periodic references to other sections of this

manual provide more detailed information.

Use only High Efficiency detergents. ]he package for this type of detergent will be marked

"HE" or "High Efficiency." [his wash system, along with less water, will create too much

sudsing with a regular non-HE detergent. Using regular detergent will likely result in washer

errors, longer cycle times and reduced rinsing performance. [t may also result in component

failures and noticeable mold or mildew. HE detergents are made to produce the right amount

of suds for the best performance. Follow the manufacturer's instructions to determine the

amount of detergent to use.

Place a load of sorted clothes into the washer. See "Laundry Tips."

• load evenly to maintain washer balance. Mix large and small items. Items should

move easily through the wash water.

• load only to the top of the basket as shown. Overloading can cause poor cleaning.

Items need to move easily through the wash water.

Pour measured powdered or liquid High Efficiency detergent into the detergent dispenser.

Always use the detergent dispenser, and do not put detergent directly onto clothes in the

washer.

_ 10.

11.

12.

3. Add color-safe bleach (powdered or liquid) to this dispenser, if needed. Be sure to match

powdered color-safe bleach with powdered detergent or match liquid color-safe bleach

with liquid detergent.

4. Pour measured liquid chlorine bleach into the liquid chlorine bleach dispenser, if needed.

Bleach is diluted and automatically dispensed at the proper time during the wash cycle.

Do not overfill. Do not dilute. Do not use more than 1 cup (250 mL) for a full load.

Use less with a smaller load size.

Follow the garment and the chlorine bleach manufacturer's directions for proper use,

lo avoid spilling, use a cup with a pouring spout. Do not let bleach splash, drip, or run

down into the washer basket.

• At the end of the cycle, a small amount of water may be left in the dispenser. This is

normal.

NOTE: Use only liquid chlorine bleach in this dispenser.

Pour measured liquid fabric softener into the fabric softener dispenser, if desired.

• Do not overfill. The dispenser holds 3 oz (94 m[), or a capful of fabric softener.

• The fabric softener is dispensed in the final rinse. [f Extra Rinse is selected, the fabric

softener will be dispensed during the Extra Rinse.

• Do not spill or drip any fabric softener onto the clothes.

• At the end of the cycle, a small amount of water may be left in the dispenser. This is

normal.

NOTE: Use only liquid fabric softener in this dispenser.

Close the washer lid.

Press POWER. This turns on the washer display.

Select a Wash Cycle. See "Cycles."

Select the desired Modifiers. See "Modifiers."

Select an Option, if desired. See "Options."

Select [Delay Wash, if desired. See "Delay Wash" in the "Modifiers" section.

Press STARE The wash cycle begins, and the display shows the estimated remaining time.

[he lid will lock.

NOTE: If you do not press Start within 5 minutes of pressing Power, the washer

automatically shuts off.

Add a Garment

You can place additional clothing in the wash when the "Add a Garment" status light is

glowing without sacrificing wash performance.

To add a garment or pause the washer at any time

I. Press PAUSE/CANCEl. once.

2. Wait until the lid lock light turns off, then open the lid.

3. Add items.

To restart the washer

1. Close the lid and press START.

2. lb unlock the lid after the Add a Garment period, press PAUSE/CANCEl once. Pressing

PAUSE/CANCEL twice will cancel the wash cycle.

!_i)iilZii!iiii_:!!ii!iii)ii)iiiiiiiiiiiiiiiiiiiiiiiiil)!:_%iii))ili i_i!iiiiiiiiiill¸¸ 15

You can stop the wash cycle and drain the tub by pressing the Pause/Cancel button twice or

the Power button once.

_9 ............

You can change Cycles, Modifiers and Options anytime before Start is pressed. Not all

Modifiers and Options are available for all cycles.

• A short tone sounds when a change is selected.

• Three short tones sound if an unavailable combination is selected. [he last selection will

not be accepted.

Changing Cycles after pressing Start

1. Press PAUSE/CANCEl twice to cancel the cycle. [-he washer will drain.

2. Press POWER.

3. Select the desired wash cycle.

4. Select the desired Modifiers and Options.

5. Press START.

The washer restarts at the beginning of the new cycle.

NOTE: if you do not press Start within 5 minutes of pausing the washer, the washer

automatically shuts off.

Changing Modifiers and Options after pressing Start

You can change a Modifier or Option anytime before the selected Modifier or Option begins

by choosing the desired Modifiers and/or Options.

NOTE: An error tone will sound if your selection is unavailable.

To manually drain the washer and spin the load

1. Press PAUSE/CANCEl twice to cancel the wash cycle and drain the washer.

2. Press POWER.

3. [urn knob to select DRAIN & SPIN.

4. Press STAR[%

When the spin is complete, the lid unlocks. Items can be removed from the washer.

These lights show which portion of the cycle the washer is operating. They also indicate when

you can add other garments to the wash load.

DELAY SOAK WASH RINSE SPIN CLEAN

_o • • • • oj

ADD A GARMENT

Indicator lights

An indicator light shows which Cycle, Modifiers and Options you have selected.

Estimated Time Remaining

When a wash cycle is started, the estimated time remaining for the cycle, including fills and

drains, will be displayed. The time will count down to the end of the cycle.

ESTIMATEDTIME

REMAINING

Turn the knob to choose the right wash cycle for the type of fabrics you are washing. When

the knob points to a cycle, the indicator light for the cycle will glow and the indicator light for

Start will blink. If the default settings for the Modifiers and Options are acceptable, you may

press Start to begin the wash cycle.

NORMAL WRINKLE

SHEETS CONTROL

COLORS/

JEANS

SUPER RAPID

WASH"

:ATE

HAND

WASH

SPIN LEAN

ONLY WASHER

WITH BLEACH

RINSI ONLY

& SPIN SOAK

Preset Cycle Settings

For ease of use, [)reset cycle settings provide the recommended fabric care settings for each

cycle.

To use the preset cycle settings:

1. Press POWER.

2. Select the cycle you want by turning the knob. The preset cycle settings will be displayed

(see following chart).

NOTE: The preset times may vary slightly depending on your model.

3. Press START. The wash cycle will begin.

Preset Cycle Settings

Cycle Preset Minutes* Soil Level** Wash/Rinse Temp

Whites 79 Heavy Hot/Cold

Super Wash 66 Heavy Hot/Cold

Bulky 46 Normal Warm/Cold

Sheets 46 Normal Warm/Cold

Normal 43 Normal Warm/Cold

Wrinkle Control 44 Medium Warm/Cold

Colors/Jeans 42 Normal Cold/Cold

Quick Wash 34 Light Warm/Warm

Delicate 36 Light Cold/Cold

Handwash 35 light Cold/Cold

Clean Washer 41 Medium Warm/Cold

with bleach only

Soak

Rinse & Spin

Spin Only

20 Not applicable Cold/Cold

10 Not applicable Not applicable

60 Not applicable Not applicable

*These times are for reference only and may not match your model exactly.

**Cycle time in minutes will appear in the display while you are making selections. The total

cycle time will appear, including an estimated time for drain and fill times, once Start is

pressed.

NOTE: I.oad only to the top of the basket. Overloading can cause poor cleaning. See "Starting

Your Washer."

Whites

This cycle introduces liquid chlorine bleach to the load at the proper time for improved

whitening of your heavily soiled white fabrics. Cycle combines high-speed wash action and

high-speed spin speed. For maximum soil and stain removal, liquid chlorine bleach must be

used.

Super Wash

Use this cycle for heavily soiled or sturdy items. Cycle combines high-speed wash action and

high-speed spin. Stain Cycle is the default option for this cycle, but it can be turned off. See

"Changing Cycles, Modifiers and Options."

Bulky

Use this cycle to wash large items such as comforters, sleeping bags and blankets. This cycle

starts with a soak to thoroughly saturate your large load. This is followed by medium wash

action and medium spin speeds to maintain load balance.

Sheets

Use this cycle for sheets, pillowcases and towels. The wash action of this cycle is designed to

keep large items from tangling and bailing up.

IMPORTANT: For best performance, drop items in loose heaps evenly around the basket wall.

Do not load items directly on the impeller for this cycle.

Normal

Use this cycle for normally soiled cottons and mixed fabric loads. Cycle combines high-speed

wash action and high-speed spin.

Wrinkle Control

Use this cycle to wash loads of no-iron fabrics such as sport shirts, blouses, casual business

clothes, permanent press and blends. This cycle uses medium-speed wash action, a low-

speed spin and a cool down process to help reduce wrinkling.

Colors/Jeans

Use this cycle for lightly soiled, dark or highly dyed natural fabrics such as cotton that may be

susceptible to dye loss. Cycle uses low to medium-speed wash action and high-speed spin.

For best results use cold or warm water.

Quick Wash

Use this cycle to wash small, lightly soiled loads that are needed in a hurry. ]his short cycle

combines high-speed wash action and high-speed spin for the best cleaning and shortened

dry times.

Delicate

Use this cycle to wash lightly soiled garments indicating "Machine Washable Silks" or

"Gentle" cycle on the care label. This cycle uses intermittent low speed wash action and low-

speed spin for optimal fabric care.

When washing waterproof items, such as plastic-lined mattress pads, shower curtains,

tarpaulins (tarps) or waterproof or water-resistant sleeping bags, use the Delicate or

Handwash cycle with the lowest spin speed setting available for the washer model that you

have.

Garments are labeled "Hand Wash" because:

• [he fiber construction may be sensitive to wash action.

• [he fabric contains sensitive dyes that may bleed.

Handwash

This cycle combines low-speed wash and low-speed spin action to clean items labeled as

"Machine Washable Wool" on the garment care label. Pre Soak and Deep Clean options are

not available in this cycle.

When washing waterproof items, such as plastic-lined mattress pads, shower curtains,

tarpaulins (tarps) or waterproof or water-resistant sleeping bags, use the Delicate or

Handwash cycle with the lowest spin speed setting available for the washer model that you

have.

Soak

This cycle is preset for a 41 -minute cycle and soak time can be adjusted according to your

needs by selecting Soil I.eveh After the selected soak period has ended, the washer will drain

but does not spin the load.

NOTE: Automatic bleach dispensing is not part of the soak cycle.

!_iiiiiZii!ili{_:!!ii!i{iii!iiiiiiiiiiiiiiiiiiiiiiii{{!!:_%ii{{ili {!iiiiiiiiiill¸ 17

Rinse & Spin

Use this option to get a deep rinse followed by a high-speed spin. The time display will

include an estimate of how long it will take to fill and drain the washer.

When to use Rinse & Spin:

• For loads that need rinsing only.

• For completing a cycle after the power has been off.

To use or change Rinse & Spin setting:

1. Turn knob to RINSE & SPIN until the Rinse & Spin indicator light glows.

2. Press STARTI

Spin Only

Spin (billy may help shorten drying times for some heavy fabrics or special-rare items. Spin

Only may also be used for draining the washer after canceling a cycle or completing a cycle

after a power failure.

To use or change Spin Only setting:

1. [urn knob to SPIN ONlY until the Spin Only indicator light glows.

2. Press START.

Clean Washer

Use the Clean Washer cycle once a month to keep the inside of your washer fresh and clean.

This cycle uses a higher water level in combination with liquid chlorine bleach to thoroughly

clean the inside of your washing machine. See "Cleaning Your Washer."

IMPORTANT: Do not add detergent to this cleaning cycle. Use only liquid chlorine bleach.

Do not place garments or other items in the washer during the Clean Washer cycle. Use this

cycle with an empty wash tub.

Modifiers allow you to further customize your cycles and save energy.

AUTO TEMP

CONTROL

(

SOIL

LEVEL

it EXTRA

HEAVY

• HEAVY

• MEDIUM

• LIGHT

SPIN

SPEED

HIGH O WARM/WARM

• MEDIUM Q WARM/COLD

• LOW • COOL!COLD

• NO SPIN • COLD/COLD

)

WASH/RINSE

TEMP

Soil Level

Soil level (wash time) is preset for each wash cycle. See "Preset Cycle Settings" in "Cycles." As

you press the Soil level pad, the cycle time (minutes) will increase or decrease in the

Estimated Time Remaining display and a different wash time will appear. 1o get the minimum

wash time, press the pad until the indicator light next to light illuminates. This is the shortest

wash time available for that cycle.

• For most loads, use the time recommended in the preset cycle settings.

• For heavy soil and sturdy fabrics, press Soil [.evel to select more wash time, if needed.

• For light soil and delicate fabrics, press Soil I.evel to select less wash time, if needed.

Spin Speed

[his washer automatically selects the spin speed based on the cycle selected. The preset

speeds can be changed. Spin speeds may vary by cycle.

Wash/Rinse Temp

Select a water temperature based on the type of load you are washing. Use the warmest wash

water safe for fabrics. Follow garment label instructions.

Warm rinses leave the loads drier and more comfortable to handle than cold rinses. However,

warm rinses also increase wrinkling. Cold rinses may help with wrinkling and save energy.

Temperature Guide

Wash WaterTemperature Suggested Fabrics

Hot Whites and pastels

Warm Bright colors

Cold Colors that bleed or fade

NOTE: In wash water temperatures colder than 60°F (15.6°C), detergents do not dissolve welL

Soils may be difficult to remove.

Auto Temp Control

Auto ]emp Control (ATC) electronically senses and maintains a uniform wash and rinse water

temperature. ATC regulates incoming hot and cold water. The ATC is automatically turned On

when a cycle is selected. (See "Preset Cycle Settings" in "Cycles.")

ATC is available with Warm/Warm, Warm/Cold and Cool/Cold settings. The water

temperature in the Hot/Cold and Cold/Cold settings depend on the water temperature at the

water inlet faucets.

• ATC ensures consistent cleaning.

• Heated water consumes the largest amount of energy that a washer uses.

• lbday's detergents work well at temperatures above 60°F (15.6°C).

Delay Wash

You can use the Delay Wash feature to delay the start of a wash cycle for up to 10 hours

(depending on your model).

load the washer and fill the dispensers.

Close the washer lid.

Press POWER.

Select the desired Cycle, Modifiers and Options.

Press DEI.AY WASH. 1H (one hour) will be displayed in the time display window. The

indicator light for Delay Wash will glow.

6. For a longer delay time, press DELAY WASH. The Start time will increase by 1-hour steps.

Press START. [he countdown in hours to the wash cycle will show in the time display

window and the indicator light will begin to flash.

NOTE: [he Start indicator light will not flash when [Delay Wash is chosen. You must press

Start to initiate a countdown for the cycle to begin.

To change the Delay Wash time:

• Press PAUSE/CANCEl.

• Press DELAY WASH to select the desired delay time.

• Press START to begin the countdown.

To cancel Delay Wash:

Press START again to begin the cycle right away or press PAUSE/CANCEl twice.

Use these pads to select the desired options for your wash cycle.

STAIN

CYCLE

Low

PRE- ENDOF

SOAK CYCLE

SIGNAL

Stain Cycle

This option provides enhanced cleaning action for tough stains. The Super Wash cycle

automatically includes Stain Cycle. Choosing Stain Cycle will add approximately 5 minutes

to a cycle. Stain Cycle should be started on a dry load only and cannot be selected after the

tub has started filling with water.

Stain Cycle may be selected as an option with other cycles. See table for details.

Cycle Stain Cycle

(Adds time to the wash cycle)

Whites Option

Super Wash Default

Bulky Not available

Sheets Not available

Cycle Stain Cycle

(Adds time to the wash cycle)

Delicate Option

Handwash Option

Clean Washer with bleach only Not available

Soak Not available

Rinse & Spin Not available

Spin Only Not available

Extra Rinse

An extra rinse can be used to aid in the removal of detergent or bleach residue from garments.

[his option provides an additional rinse with the same water temperature as the first rinse.

[his is the default rinse setting for the Whites cycle.

Pre Soak

Use this option for set-in stains and soil that need extra time for removal. Soaking ill this

washer is different than in a conventional washer. ]he washer sprays the load with water and :::ii

detergent at extra-low spin speed followed by a brief period of wash action at the speed of the

selected cycle. This action is repeated. Pre Soak cycles through a series of sprays and wash

actions followed by a pause to allow the detergent to work on the soils. ]he Pre Soak feature

is followed by the selected cycle. Using Pre Soak will extend your wash cycle.

End of Cycle Signal Volume

[he End of Cycle Signal produces an audible sound when the wash cycle is finished. This

signal is helpful when you are removing items from the washer as soon as it stops. Select

High, I.ow or Off.

POWER

START

PAUSE/

CANCEL

LID L_CK

Normal Option

Wrinkle Control Option

Colors/Jeans Option

Quick Wash Option

Powe r

PressPOWER to turn tile washer on or off.

Start

Press START to start your washer after a cycle has been selected. Be sure all desired Modifiers

and Options have been selected. The lid must be closed for the washer to start.

Pause/Cancel

Press PAUSE/CANCEl. once to pause or stop the washer at any time. Press PAUSE/CANCEL

once to unlock the lid and add a garment. Press START to complete the cycle from where it

was stopped. Press PAUSE/CANCEl twice to stop the wash cycle, The washer will then drain

and turn off.

Lid Lock

When the I.id [.ock status light glows, the washer lid is locked.

NOTE: You must wait until the I.id I.ock I.ight turns off before the lid can be opened.

Your new washer may make sounds your old one didn't. Because the sounds might be

unfamiliar, you may be concerned about them. These sounds are normal.

During washing

If you select the Stain Cycle option, you will hear a spin/spray noise at the start of the cycle.

During drain

If water is drained quickly from your washer (depending on your installation you may hear

air being pulled through the pump during the end of draining.

During wash and spin

[his washer does not have a transmission. ]he motor provides direct drive for agitation and

spin. You will hear sounds that are different from those of a conventional washer.

Preparing clothes for washing

Follow these recommendations to help you prolong the life of your garments.

• Use only High Efficiency detergents. [he package for this type of detergent will be marked

"HE" or "High Efficiency." This wash system, along with less water, will create too much

sudsing with a regular non-HE detergent. Using regular detergent will likely result in washer

errors, longer cycle times, and reduced rinsing performance. [t may also result in component

failures and noticeable mold or mildew. HE detergents are made to produce the right

amount of suds for the best performance. Follow the manufacturer's instructions to

determine the amount of detergent to use.

Use only "HE" High Efficiency detergent.

• Close zippers, snaps, and hooks to avoid snagging other items. Remove pins, buckles, and

other hard objects to avoid scratching the washer interior. Remove non-washable trim and

ornaments.

• Empty pockets and turn them inside-out.

• Turn down cuffs; brush away lint and dirt.

• Turn synthetic knits inside-out to avoid pilling.

• Tie strings and sashes so they will not tangle.

• Mend tears, loose hems, and seams.

• Treat spots and stains.

• Stained or wet garments should be washed promptly for best results.

• Turn wool knits inside-out before washing.

Sorting

• Separate heavily soiled items from lightly soiled ones, even if they would normally be

washed together. Separate lint-givers (towels, chenille) from lint-takers (corduroy,

synthetics, permanent press). When possible, turn lint-givers inside-out.

• Separate dark colors from light colors, colorfast items from noncolorfast items.

• Sort by fabric and construction (sturdy cottons, knits, delicate items).

• Separate bulky, nonabsorbent items such as comforters, pillows and poly-filled jackets.

Use the Bulky cycle for these items.

• Separate sheets, pillowcases and towels and use the Sheets cycle for these items. For best

performance, drop items in loose heaps evenly around the basket wall and do not load

items directly on the impeller for this cycle.

• When washing waterproof items, such as plastic-lined mattress pads, shower curtains,

tarpaulin (tarps) or waterproof or water-resistant sleeping bags, use the Delicate or

Handwash cycle with the lowest spin speed setting available for the washer model that

you have.

Unloading

• Remove clothes from washer after the cycle is completed. Metal objects such as zippers,

snaps, and buckles may rust if left in the washer basket for a long time.

La page charge ...

Maytag BRAVOS MTW6600TQ0 Manuel utilisateur

Marque: Maytag

Modèle: BRAVOS MTW6600TQ0

Catégorie: Machines à laver

Taper: Manuel utilisateur

Ce manuel convient également à

BRAVOS MTW6600TB0

Télécharger le PDF

rapport

dans d''autres langues

English: Maytag BRAVOS MTW6600TQ0 User manual
español: Maytag BRAVOS MTW6600TQ0 Manual de usuario

Maytag BRAVOS MTW6600TQ0 Manuel utilisateur

Ce manuel convient également à

Maytag BRAVOS MTW6600TQ0 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents