Sony CDX-GT44IP Le manuel du propriétaire

CDX-GT44IP

Operating Instructions

Bedienungsanleitung

Mode d’emploi

Istruzioni per l’uso

Gebruiksaanwijzing

3-217-561-22 (1)

GB

DE

FR

IT

NL

To cancel the demonstration (DEMO) display, see page 12.

Zum Deaktivieren der Demo-Anzeige (DEMO) schlagen Sie bitte auf Seite 13 nach.

Pour annuler la démonstration (DEMO), reportez-vous à la page 13.

Per annullare la dimostrazione (DEMO), vedere pagina 13.

Om de demonstratie (DEMO) te annuleren, zie pagina 13.

©

2007 Sony Corporation

FM

/

MW

/

LW

Compact Disc Player

2

iPod is a trademark of Apple Inc., registered in

the U.S. and other countries.

For installation and connections, see the

supplied installation/connections manual.

This label is located on the bottom of the

chassis.

The manufacturer of this product is Sony

Corporation, 1-7-1 Konan Minato-ku Tokyo,

108-0075 Japan.

The Authorized Representative for EMC and

product safety is Sony Deutschland GmbH,

Hedelfinger Strasse 61, 70327 Stuttgart,

Germany. For any service or guarantee matters

please refer to the addresses given in separate

service or guarantee documents.

Disposal of Old Electrical &

Electronic Equipment (Applicable in

the European Union and other

European countries with separate

collection systems)

This symbol on the product or on its

packaging indicates that this product shall not be treated

as household waste. Instead it shall be handed over to the

applicable collection point for the recycling of electrical

and electronic equipment. By ensuring this product is

disposed of correctly, you will help prevent potential

negative consequences for the environment and human

health, which could otherwise be caused by inappropriate

waste handling of this product. The recycling of materials

will help to conserve natural resources. For more detailed

information about recycling of this product, please contact

your local Civic Office, your household waste disposal

service or the shop where you purchased the product.

Applicable accessory: Remote commander

Warning if your car’s ignition has no

ACC position

Be sure to set the Auto Off function (page 12).

The unit will shut off completely and

automatically in the set time after the unit is

turned off, which prevents battery drain.

If you do not set the Auto Off function, press

and hold (OFF) until the display disappears

each time you turn the ignition off.

Disposal of waste batteries

(applicable in the European Union

and other European countries with

separate collection systems)

This symbol on the battery or on the packaging indicates

that the battery provided with this product shall not be

treated as household waste. By ensuring these batteries are

disposed of correctly, you will help prevent potentially

negative consequences for the environment and human

health which could otherwise be caused by inappropriate

waste handling of the battery. The recycling of the

materials will help to conserve natural resources.

In case of products that for safety, performance or data

integrity reasons require a permanent connection with an

incorporated battery, this battery should be replaced by

qualified service staff only. To ensure that the battery will

be treated properly, hand over the product at end-of-life to

the applicable collection point for the recycling of

electrical and electronic equipment.

For all other batteries, please view the section on how to

remove the battery from the product safely. Hand the

battery over to the applicable collection point for the

recycling of waste batteries.

For more detailed information about recycling of this

product or battery, please contact your local Civic Office,

your household waste disposal service or the shop where

you purchased the product.

Microsoft, Windows Media,

and the Windows logo are

trademarks or registered

trademarks of Microsoft

Corporation in the United States and/or other

countries.

3

Table of Contents

Welcome ! . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Getting Started

Resetting the unit. . . . . . . . . . . . . . . . . . . . . . . . 4

Preparing the card remote commander . . . . . . . 4

Setting the clock . . . . . . . . . . . . . . . . . . . . . . . . 4

Detaching the front panel . . . . . . . . . . . . . . . . . 5

Attaching the front panel . . . . . . . . . . . . . . . 5

Location of controls and basic

operations

Main unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Card remote commander RM-X151 . . . . . . 6

CD

Display items . . . . . . . . . . . . . . . . . . . . . . . . 8

Repeat and shuffle play. . . . . . . . . . . . . . . . . 8

Radio

Storing and receiving stations . . . . . . . . . . . . . . 8

Storing automatically — BTM . . . . . . . . . . . 8

Storing manually. . . . . . . . . . . . . . . . . . . . . . 8

Receiving the stored stations . . . . . . . . . . . . 8

Tuning automatically . . . . . . . . . . . . . . . . . . 8

RDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Setting AF and TA . . . . . . . . . . . . . . . . . . . . 9

Selecting PTY . . . . . . . . . . . . . . . . . . . . . . . 10

Setting CT. . . . . . . . . . . . . . . . . . . . . . . . . . 10

iPod

Playing back iPod . . . . . . . . . . . . . . . . . . . . . . 10

Playing tracks . . . . . . . . . . . . . . . . . . . . . . . 10

Display items . . . . . . . . . . . . . . . . . . . . . . . 11

Setting the play mode . . . . . . . . . . . . . . . . . . . 11

Selecting Album, Artist or Playlist. . . . . . . 11

Repeat and shuffle play. . . . . . . . . . . . . . . . 11

Scan. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Other functions

Changing the sound settings . . . . . . . . . . . . . . 12

Adjusting the sound characteristics

— BAL/FAD/SUB. . . . . . . . . . . . . . . . . . . 12

Customizing the equalizer curve

— EQ3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Adjusting setup items — SET . . . . . . . . . . . . 12

Using optional equipment. . . . . . . . . . . . . . . . 13

Auxiliary audio equipment. . . . . . . . . . . . . 13

Additional Information

Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Notes on discs . . . . . . . . . . . . . . . . . . . . . . 14

Playback order of MP3/WMA files . . . . . 15

About MP3 files . . . . . . . . . . . . . . . . . . . . . 15

About WMA files. . . . . . . . . . . . . . . . . . . . 15

About iPod . . . . . . . . . . . . . . . . . . . . . . . . . 15

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Removing the unit. . . . . . . . . . . . . . . . . . . . . . 16

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . 16

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . 17

Error displays/Messages. . . . . . . . . . . . . . . 18

4

Welcome !

Thank you for purchasing this Sony Compact

Disc Player. You can enjoy your drive with the

following functions.

• CD playback

You can play CD-DA (also containing CD

TEXT) and CD-R/CD-RW (MP3/WMA files

(

page 15)).

• Radio reception

– You can store up to 6 stations per band (FM1,

FM2, FM3, MW and LW).

– BTM (Best Tuning Memory): the unit selects

strong signal stations and stores them.

• RDS services

– You can use FM station with Radio Data

System (RDS).

• Sound adjustment

– EQ3 stage2: You can choose any one of 7

preset equalizer curves.

• iPod operation

iPod connection can be made by the dock

connector cable on the rear of the unit.

• Auxiliary equipment connection

An AUX input jack on the front of the unit

allows connection of a portable audio device.

Getting Started

Resetting the unit

Before operating the unit for the first time, or

after replacing the car battery or changing the

connections, you must reset the unit.

Detach the front panel and press the RESET

button with a pointed object, such as a ball-point

pen.

Note

Pressing the RESET button will erase the clock setting

and some stored contents.

Preparing the card remote

commander

Before using the card remote commander for the

first time, remove the insulation film.

Tip

For how to replace the battery, see “Replacing the

lithium battery of the card remote commander” on

page 15.

Setting the clock

The clock uses a 24-hour digital indication.

1 Press and hold the select button.

The setup display appears.

2 Press the select button repeatedly

until “CLOCK-ADJ” appears.

3 Press (SEEK) +.

The hour indication flashes.

4 Rotate the volume control dial to set

the hour and minute.

To move the digital indication, press (SEEK)

–/+.

5 Press the select button.

The setup is complete and the clock starts.

To display the clock, press (DSPL). Press

(DSPL) again to return to the previous display.

Type of discs Label on the disc

CD-DA

MP3

WMA

RESET

button

5

Tip

You can set the clock automatically with the RDS

feature (

page 10).

Detaching the front panel

You can detach the front panel of this unit to

prevent theft.

Caution alarm

If you turn the ignition switch to the OFF

position without detaching the front panel, the

caution alarm will sound for a few seconds.

The alarm will only sound if the built-in

amplifier is used.

1 Press (OFF).

The unit is turned off.

2 Press , then pull it off towards you.

Notes

• Do not drop or put excessive pressure on the front

panel and display window.

• Do not subject the front panel to heat/high

temperature or moisture. Avoid leaving it in a parked

car or on a dashboard/rear tray.

Attaching the front panel

Engage part A of the front panel with part B of

the unit, as illustrated, and push the left side into

position until it clicks.

Note

Do not put anything on the inner surface of the front

panel.

B

A

6

Location of controls and basic operations

Main unit

Card remote commander

RM-X151

This section contains instructions on the location

of controls and basic operations. For details, see

the respective pages.

For iPod operation, see “iPod” on page 10. The

corresponding buttons on the card remote

commander control the same functions as those

on the unit.

A OFF button

To power off; stop the source.

B EQ3 (equalizer) button page 12

To select an equalizer type (XPLOD,

VOCAL, EDGE, CRUISE, SPACE,

GRAVITY, CUSTOM or OFF).

C Volume control dial/select button

page 12

To adjust volume (rotate); select setup items

(press and rotate).

D SOURCE button

To power on; change the source (Radio/CD/

AUX/PD).

E Disc slot

Insert the disc (label side up), playback

starts.

F Display window

G AUX input jack page 13

To connect a portable audio device.

H Z (eject) button

To eject the disc.

I (front panel release) button page 5

SEEK

SCRL

SEEK

PAUSEALBUM REP SHUF

EQ3

DSPL

OFF

AF/TA

PTY

PUSH SELECT

1623 54

MODE

SOURCE

AUX

1

q

;

9

2

q

h

q

g

4 5 8673

qa qs qd

qf

OFF

DSPL

SCRL

SEL

SOURCE

MODE

132

465

ATT

VOL

+

–

+

–

4

wa

qs

1

wd

qj

qk

w;

ql

wf

ws

7

J DSPL (display)/SCRL (scroll) button

page 8, 9

To change display items (press); scroll the

display item (press and hold).

K SEEK –/+ buttons

CD/PD:

To skip tracks (press); skip tracks

continuously (press, then press again within

about 1 second and hold); reverse/fast-

forward a track (press and hold).

Radio:

To tune in stations automatically (press); find

a station manually (press and hold).

L MODE button page 8

To select the radio band (FM/MW/LW);

select the play mode of iPod.

M AF (Alternative Frequencies)/

TA

(Traffic Announcement)/

PTY

(Program Type) button page 9,

10

To set AF and TA (press); select PTY (press

and hold) in RDS.

N RESET button (located behind the front

panel)

page 4

O Number buttons

CD/PD:

(1)/(2): ALBUM –/+ (during MP3/WMA

playback)

To skip albums (press); skip albums

continuously (press and hold).

(3): REP page 8

(4): SHUF page 8

(6): PAUSE

To pause playback. To cancel, press

again.

Radio:

To receive stored stations (press); store

stations (press and hold).

P Receptor for the card remote

commander

The following buttons on the card remote

commander have also different buttons/functions

from the unit. Remove the insulation film before

use (

page 4).

qj < (.)/, (>) buttons

To control CD/radio/PD, the same as

(SEEK) –/+ on the unit.

Setup, sound setting, etc., can be operated by

< ,.

qk DSPL (display) button

To change display items.

ql VOL (volume) +/– button

To adjust volume.

w; ATT (attenuate) button

To attenuate the sound. To cancel, press

again.

wa SEL (select) button

The same as the select button on the unit.

ws M (+)/m (–) buttons

To control CD/PD, the same as (1)/(2)

(ALBUM –/+) on the unit.

Setup, sound setting, etc., can be operated by

M m.

wd SCRL (scroll) button

To scroll the display item.

wf Number buttons

To receive stored stations (press); store

stations (press and hold).

Note

If the unit is turned off and the display disappears, it

cannot be operated with the card remote commander

unless (SOURCE) on the unit is pressed, or a disc is

inserted to activate the unit first.

8

CD

Display items

A Source

B Track number/Elapsed playing time, Disc/

artist name, Album number*

1

, Album name,

Track name, Text information*

2

, Clock

*1 Album number is displayed only when the album is

changed.

*2 When playing an MP3, ID3 tag is displayed, and

when playing a WMA, WMA tag is displayed.

To change display items B, press (DSPL).

Tip

Displayed items may differ depending on disc type,

recording format and settings. For details on MP3/

WMA, see

page 15.

Repeat and shuffle play

1 During playback, press (3) (REP) or

(4) (SHUF) repeatedly until the

desired setting appears.

* When an MP3/WMA is played.

To return to normal play mode, select “ OFF”

or “SHUF OFF.”

Radio

Storing and receiving stations

Caution

When tuning in stations while driving, use Best

Tuning Memory (BTM) to prevent an accident.

Storing automatically — BTM

1 Press (SOURCE) repeatedly until

“TUNER” appears.

To change the band, press (MODE)

repeatedly. You can select from FM1, FM2,

FM3, MW or LW.

2 Press and hold the select button.

The setup display appears.

3 Press the select button repeatedly

until “BTM” appears.

4 Press (SEEK) +.

The unit stores stations in order of frequency

on the number buttons.

A beep sounds when the setting is stored.

Storing manually

1 While receiving the station that you

want to store, press and hold a

number button ((1) to (6)) until

“MEM” appears.

Note

If you try to store another station on the same number

button, the previously stored station will be replaced.

Tip

When an RDS station is stored, the AF/TA setting is

also stored (

page 9).

Receiving the stored stations

1 Select the band, then press a number

button ((1) to (6)).

Tuning automatically

1 Select the band, then press (SEEK) –/+

to search for the station.

Scanning stops when the unit receives a

station. Repeat this procedure until the

desired station is received.

Tip

If you know the frequency of the station you want to

listen to, press and hold (SEEK)

–/+ to locate the

approximate frequency, then press (SEEK)

–/+

repeatedly to fine adjust to the desired frequency

(manual tuning).

Select To play

TRACK track repeatedly.

ALBUM* album repeatedly.

SHUF ALBUM* album in random order.

SHUF DISC disc in random order.

9

RDS

Overview

FM stations with Radio Data System (RDS)

service send inaudible digital information along

with the regular radio program signal.

Display items

A TA/TP*

1

B Radio band, Function

C Frequency*

2

(Program service name), Preset

number, Clock, RDS data

*1 “TA” flashes during traffic information. “TP” lights

up while such a station is received.

*2 While receiving the RDS station, “ *” is displayed

on the left of the frequency indication.

To change display items C, press (DSPL).

RDS services

This unit automatically provides RDS services as

follows:

Notes

• Depending on the country/region, not all RDS

functions may be available.

• RDS will not work if the signal strength is too weak,

or if the station you are tuned to is not transmitting

RDS data.

Setting AF and TA

1 Press (AF/TA) repeatedly until the

desired setting appears.

Storing RDS stations with the AF and

TA setting

You can preset RDS stations along with the AF/

TA setting. If you use the BTM function, only

RDS stations are stored with the same AF/TA

setting.

If you preset manually, you can preset both RDS

and non-RDS stations with the AF/TA setting for

each.

1 Set AF/TA, then store the station with BTM or

manually.

Receiving emergency

announcements

With AF or TA on, the emergency

announcements will automatically interrupt the

currently selected source.

Tip

If you adjust the volume level during a traffic

announcement, that level will be stored into memory

for subsequent traffic announcements, independently

from the regular volume level.

Staying with one regional program

— REG

When the AF function is on: this unit’s factory

setting restricts reception to a specific region, so

you will not be switched to another regional

station with a stronger frequency.

If you leave this regional program’s reception

area, set “REG-OFF” in setup during FM

reception (

page 13).

Note

This function does not work in the UK and in some

other areas.

AF (Alternative Frequencies)

Selects and retunes the station with the

strongest signal in a network. By using this

function, you can continuously listen to the

same program during a long-distance drive

without having to retune the same station

manually.

TA (Traffic Announcement)/TP (Traffic

Program)

Provides current traffic information/programs.

Any information/program received, will

interrupt the currently selected source.

PTY (Program Types)

Displays the currently received program type.

Also searches your selected program type.

CT (Clock Time)

The CT data from the RDS transmission sets

the clock.

Select To

AF-ON activate AF and deactivate TA.

TA-ON activate TA and deactivate AF.

AF, TA-ON activate both AF and TA.

AF, TA-OFF deactivate both AF and TA.

continue to next page t

10

Local Link function (UK only)

This function enables you to select other local

stations in the area, even if they are not stored on

your number buttons.

1 During FM reception, press a number button

((1) to (6)) on which a local station is stored.

2 Within 5 seconds, press again a number button

of the local station.

Repeat this procedure until the local station is

received.

Selecting PTY

1 Press and hold (AF/TA) (PTY) during

FM reception.

The current program type name appears if the

station is transmitting PTY data.

2 Press (AF/TA) (PTY) repeatedly until

the desired program type appears.

3 Press (SEEK) –/+.

The unit starts to search for a station

broadcasting the selected program type.

Type of programs

Note

You cannot use this function in countries/regions

where no PTY data is available.

Setting CT

1 Set “CT-ON” in setup (page 12).

Notes

• The CT function may not work even though an RDS

station is being received.

• There might be a difference between the time set by

the CT function and the actual time.

iPod

Playing back iPod

By connecting an iPod to the dock connector at

the rear of the unit, you can listen on your car

speakers, while controlling the iPod from the

unit.

Notes

• When an iPod is connected to the dock connector,

operation from the iPod cannot be performed.

• Before connecting the iPod to the dock connector,

turn down the volume of the unit.

Playing tracks

1 Connect the iPod to the dock

connector.

The iPod will turn on automatically, and the

display will appear on the iPod screen as

below.

2 Press (SOURCE) repeatedly until “PD”

appears.

“PD 1 PORTABLE” appears, and the tracks

on the iPod start playing automatically from

the point last played.

3 Press (MODE) to select the play mode.

The mode changes as follows:

RESUMING t ALBUM t ARTIST t

PLAYLIST

4 Adjust the volume.

Press (OFF) to stop playback.

NEWS (News), AFFAIRS (Current Affairs),

INFO (Information), SPORT (Sports),

EDUCATE (Education), DRAMA (Drama),

CULTURE (Culture), SCIENCE (Science),

VARIED (Varied), POP

M (Popular Music),

ROCK

M (Rock Music), EASY M (Easy

Listening), LIGHT

M (Light Classical),

CLASSICS (Classical), OTHER

M (Other

Music Type), WEATHER (Weather),

FINANCE (Finance), CHILDREN (Children’s

Programs), SOCIAL

A (Social Affairs),

RELIGION (Religion), PHONE

IN (Phone In),

TRAVEL (Travel), LEISURE (Leisure), JAZZ

(Jazz Music), COUNTRY (Country Music),

NATION

M (National Music), OLDIES (Oldies

Music), FOLK

M (Folk Music), DOCUMENT

(Documentary)

>

.

M

E

N

U

11

Tips

• When the iPod is connected to the dock connector,

the mode changes to the Resuming mode. In

Resuming mode, pressing (3)

(Repeat),

(4)

(Shuffle) or (5) (Scan) does not function. If you

cancel Resuming mode by pressing (MODE) or (1)/

(2) (ALBUM –/+), (3)

(Repeat), (4) (Shuffle) or

(5)

(Scan) now function to change the play mode.

• When the ignition key is turned to the ACC position,

or the unit is on, the iPod will be recharged.

• If the iPod is disconnected during playback,

playback will pause.

Note

An another iPod cannot be connected using the XA-

110IP.

Display items

To change display items, press (DSPL).

Note

Some letters stored in iPod may not be displayed

correctly.

Setting the play mode

Selecting Album, Artist or Playlist

1 During playback, press (MODE).

The mode changes as follows:

ALBUM t ARTIST t PLAYLIST

Skipping albums, artists and

playlists

Repeat and shuffle play

1 During playback, press (3) (REP) or

(4) (SHUF) repeatedly until the

desired setting appears.

To return to normal play mode, select “REP

OFF” or “SHUF OFF.”

Note

(1)/(2) (ALBUM –/+) will not work during shuffle play.

Scan

You can quickly locate a specific point on the

iPod.

1 During playback, press (5) until

“SCAN ON” appears.

The first 10 seconds of each track will be

played.

To return to normal play mode, select “SCAN

OFF.”

Note

This function will not work during shuffle play.

To Press

Skip (1)/(2) (ALBUM –/+)

[press once for each]

Skip

continuously

(1)/(2) (ALBUM –/+)

[hold to desired point]

Track/album/artist name, Track number,

Elapsed playing time, Clock

Select To play

REP TRK track repeatedly.

REP ALB album repeatedly.

REP ART artist repeatedly.

REP PLY playlist repeatedly.

SHUF ALB album in random order.

SHUF ART artist in random order.

SHUF PLY playlist in random order.

SHUF ALL all tracks in random order.

12

Other functions

Changing the sound settings

Adjusting the sound

characteristics — BAL/FAD/SUB

You can adjust the balance, fader, and subwoofer

volume.

1 Press the select button repeatedly

until “BAL,” “FAD” or “SUB” appears.

The item changes as follows:

LOW*

1

t MID*

1

t HI*

1

t

BAL (left-right) t FAD (front-rear) t

SUB (subwoofer volume)*

2

t AUX*

3

*1 When EQ3 is activated (page 12).

*2 When the audio output is set to “SUB”

(page 12).

“ATT” is displayed at the lowest setting, and can

be adjusted up to 21 steps.

*3 When AUX source is activated (page 13).

2 Rotate the volume control dial to

adjust the selected item.

After 3 seconds, the setting is complete and

the display returns to normal play/reception

mode.

Customizing the equalizer curve

— EQ3

“CUSTOM” of EQ3 allows you to make your

own equalizer settings.

1 Select a source, then press (EQ3)

repeatedly to select “CUSTOM.”

2 Press the select button repeatedly

until “LOW,” “MID” or “HI” appears.

3 Rotate the volume control dial to

adjust the selected item.

The volume level is adjustable in 1 dB steps,

from –10 dB to +10 dB.

Repeat steps 2 and 3 to adjust the equalizer

curve.

To restore the factory-set equalizer curve,

press and hold the select button before the

setting is complete.

After 3 seconds, the setting is complete and

the display returns to normal play/reception

mode.

Tip

Other equalizer types are also adjustable.

Adjusting setup items — SET

1 Press and hold the select button.

The setup display appears.

2 Press the select button repeatedly

until the desired item appears.

3 Rotate the volume control dial to

select the setting (example “ON” or

“OFF”).

4 Press and hold the select button.

The setup is complete and the display returns

to normal play/reception mode.

Note

Displayed items will differ, depending on the source

and setting.

The following items can be set (follow the page

reference for details):

“z” indicates the default settings.

CLOCK-ADJ (Clock Adjust) (page 4)

CT (Clock Time)

To set “CT-ON” or “CT-OFF” (z) (page 9, 10).

BEEP

To set “BEEP-ON” (z) or “BEEP-OFF.”

AUX-A*

1

(AUX Audio)

To turn the AUX source display “AUX-A-ON”

(

z) or “AUX-A-OFF” (page 13).

A.OFF (Auto Off)

To shut off automatically after a desired time

when the unit is turned off,

– “A.OFF-NO” (

z), “A.OFF-30S (Seconds),”

“A.OFF-30M (Minutes)” or “A.OFF-60M

(Minutes).”

SUB/REAR*

1

To switch the audio output.

– “SUB-OUT” (

z): to output to a subwoofer.

– “REAR-OUT”: to output to a power amplifier.

DEMO

(Demonstration)

To set “DEMO-ON” (z) or “DEMO-OFF.”

DIM (Dimmer)

To change the brightness of the display.

– “DIM-ON”: to dim the display.

–“DIM-OFF” (

z): to deactivate the dimmer.

M.DSPL (Motion Display)

To select the Motion Display mode.

– “M.DSPL-SA” (

z): to show moving patterns

and spectrum analyzer.

– “M.DSPL-OFF”: to deactivate the Motion

Display.

A.SCRL (Auto Scroll)

To scroll long displayed item automatically

when the disc/album/track is changed.

– “A.SCRL-ON” (

z): to scroll.

– “A.SCRL-OFF”: to not scroll.

13

Using optional equipment

Auxiliary audio equipment

By connecting an optional portable audio device

to the AUX input jack (stereo mini jack) on the

unit and then simply selecting the source, you

can listen on your car speakers. The volume level

is adjustable for any difference between the unit

and the portable audio device. Follow the

procedure below:

Connecting the portable audio

device

1 Turn off the portable audio device.

2 Turn down the volume on the unit.

3 Connect to the unit.

* Be sure to use a straight type plug.

Adjust the volume level

Be sure to adjust the volume for each connected

audio device before playback.

1 Turn down the volume on the unit.

2 Press (SOURCE) repeatedly until “AUX”

appears.

“AUX FRONT IN” appears.

3 Start playback of the portable audio device at a

moderate volume.

4 Set your usual listening volume on the unit.

5 Press the select button repeatedly until “AUX”

appears, and rotate the volume control dial to

adjust the input level (–8 dB to +18 dB).

LOCAL (Local Seek Mode)

– “LOCAL-ON” : to only tune into stations with

stronger signals.

– “LOCAL-OFF” (

z): to tune normal reception.

MONO*

2

(Monaural Mode)

To improve poor FM reception, select monaural

reception mode.

– “MONO-ON” : to hear stereo broadcast in

monaural.

– “MONO-OFF” (

z): to hear stereo broadcast in

stereo.

REG*

2

(Regional)

To set “REG-ON” (

z) or “REG-OFF” (page 9).

LPF*

3

(Low Pass Filter)

To select the subwoofer cut-off frequency: “LPF

OFF” (

z), “LPF125Hz” or “LPF 78Hz.”

LOUD (Loudness)

To allow you to listen clearly at low volume

levels.

– “LOUD-ON” : to reinforce bass and treble.

– “LOUD-OFF” (

z): to not reinforce bass and

treble.

BTM (page 8)

*1 When the unit is turned off.

*2 When FM is received.

*3 When the audio output is set to “SUB.”

AUX

Connecting cord*

(not supplied)

14

Additional Information

Precautions

• If your car has been parked in direct sunlight,

allow the unit to cool off before operating it.

• Power antenna (aerial) will extend automatically

while the unit is operating.

Moisture condensation

On a rainy day or in a very damp area, moisture

condensation may occur inside the lenses and

display of the unit. Should this occur, the unit will

not operate properly. In such a case, remove the disc

and wait for about an hour until the moisture has

evaporated.

To maintain high sound quality

Be careful not to splash juice or other soft drinks

onto the unit or discs.

Notes on discs

• To keep a disc clean, do not touch its surface.

Handle the disc by its edge.

• Keep your discs in their cases or disc magazines

when not in use.

• Do not subject discs to heat/high temperature.

Avoid leaving them in a parked car or on a

dashboard/rear tray.

• Do not attach labels, or use discs with sticky ink/

residue. Such discs may stop spinning when used,

causing a malfunction, or may ruin the disc.

• Do not use any discs with labels or stickers

attached.

The following malfunctions may result from using

such discs:

– Inability to eject a disc (due to a label or sticker

peeling off and jamming the eject mechanism).

– Inability to read audio data correctly (e.g.,

playback skipping, or no playback) due to heat

shrinking of a sticker or label causing a disc to

warp.

• Discs with non-standard shapes (e.g., heart,

square, star) cannot be played on this unit.

Attempting to do so may damage the unit. Do not

use such discs.

• You cannot play 8 cm (3

1

/4 in) CDs.

• Before playing, clean the discs

with a commercially available

cleaning cloth. Wipe each disc

from the center out. Do not use

solvents such as benzine,

thinner, commercially available

cleaners, or antistatic spray

intended for analog discs.

Notes on CD-R/CD-RW discs

• Some CD-Rs/CD-RWs (depending on the

equipment used for its recording or the condition

of the disc) may not play on this unit.

• You cannot play a CD-R/a CD-RW that is not

finalized.

• The unit is compatible with the ISO 9660 level 1/

level 2 format, Joliet/Romeo in the expansion

format, and Multi Session.

• The maximum number of:

– folders (albums): 150 (including root and empty

folders).

– files (tracks) and folders contained in a disc: 300

(if a folder/file names contain many characters,

this number may become less than 300).

– displayable characters for a folder/file name is

32 (Joliet), or 64 (Romeo).

• When the disc is recorded in Multi Session, only

the first track of the first session format is

recognized and played (any other format is

skipped). The priority of the format is CD-DA and

MP3/WMA.

– When the first track is a CD-DA, only CD-DA of

the first session is played.

– When the first track is not a CD-DA, the MP3/

WMA session is played. If the disc has no data

in any of these formats, “NO MUSIC” is

displayed.

Music discs encoded with copyright

protection technologies

This product is designed to play back discs that

conform to the Compact Disc (CD) standard.

Recently, various music discs encoded with

copyright protection technologies are marketed by

some record companies. Please be aware that among

those discs, there are some that do not conform to

the CD standard and may not be playable by this

product.

Note on DualDiscs

A DualDisc is a two sided disc product which

mates DVD recorded material on one side with

digital audio material on the other side. However,

since the audio material side does not conform to

the Compact Disc (CD) standard, playback on this

product is not guaranteed.

15

Playback order of MP3/WMA files

About MP3 files

• MP3, which stands for MPEG-1 Audio Layer-3, is

a music file compression format standard. It

compresses audio CD data to approximately 1/10

of its original size.

• ID3 tag versions 1.0, 1.1, 2.2, 2.3 and 2.4 apply to

MP3 only. ID3 tag is 15/30 characters (1.0 and

1.1), or 63/126 characters (2.2, 2.3 and 2.4).

• When naming an MP3 file, be sure to add the file

extension “.mp3” to the file name.

• During playback or fast-forward/reverse of a VBR

(variable bit rate) MP3 file, elapsed playing time

may not display accurately.

Note

If you play a high-bit-rate MP3, such as 320 kbps,

sound may be intermittent.

About WMA files

• WMA, which stands for Windows Media Audio,

is a music file compression format standard. It

compresses audio CD data to approximately 1/22*

of its original size.

• WMA tag is 63 characters.

• When naming a WMA file, be sure to add the file

extension “.wma” to the file name.

• During playback or fast-forward/reverse of a VBR

(variable bit rate) WMA file, elapsed playing time

may not display accurately.

* only for 64 kbps

Note

Playback of the following WMA files is not supported.

– lossless compression

– copyright-protected

About iPod

This unit can be used with the dock connector type

iPod, iPod photo, iPod mini and iPod nano with the

following software versions. All other versions

earlier than listed are not guaranteed.

– Third-generation iPod: Ver.2.3.0

– Fourth-generation iPod: Ver.3.1.1

– Fifth-generation iPod: Ver.1.2

– iPod photo: Ver.1.2.1

– iPod mini: Ver.1.4.1

– First-generation iPod nano: Ver.1.3

– Second-generation iPod nano: Ver.1.1

(video function of fifth-generation iPod and

photo function of iPod photo are not supported).

If you have any questions or problems concerning

your unit that are not covered in this manual, consult

your nearest Sony dealer.

Maintenance

Replacing the lithium battery of the

card remote commander

Under normal conditions, the battery will last

approximately 1 year. (The service life may be

shorter, depending on the conditions of use.)

When the battery becomes weak, the range of the

card remote commander becomes shorter. Replace

the battery with a new CR2025 lithium battery. Use

of any other battery may present a risk of fire or

explosion.

Notes on the lithium battery

• Keep the lithium battery out of the reach of children.

Should the battery be swallowed, immediately

consult a doctor.

• Wipe the battery with a dry cloth to assure a good

contact.

• Be sure to observe the correct polarity when

installing the battery.

• Do not hold the battery with metallic tweezers,

otherwise a short-circuit may occur.

Folder

(album)

MP3/WMA file

(track)

MP3/WMA

continue to next page t

1

2

+ side up

c

WARNING

Battery may explode if mistreated.

Do not recharge, disassemble, or dispose of

in fire.

16

Fuse replacement

When replacing the fuse, be

sure to use one matching the

amperage rating stated on the

original fuse. If the fuse blows,

check the power connection and

replace the fuse. If the fuse

blows again after replacement,

there may be an internal

malfunction. In such a case,

consult your nearest Sony

dealer.

Cleaning the connectors

The unit may not function properly if the connectors

between the unit and the front panel are not clean. In

order to prevent this, detach the front panel (page 5)

and clean the connectors with a cotton swab. Do not

apply too much force. Otherwise, the connectors

may be damaged.

Notes

• For safety, turn off the ignition before cleaning the

connectors, and remove the key from the ignition

switch.

• Never touch the connectors directly with your fingers

or with any metal device.

Removing the unit

1 Remove the protection collar.

1 Detach the front panel (page 5).

2 Engage the release keys together with the

protection collar.

3Pull out the release keys to remove the

protection collar.

2 Remove the unit.

1Insert both release keys simultaneously

until they click.

2Pull the release keys to unseat the unit.

3Slide the unit out of the mounting.

Specifications

CD Player section

Signal-to-noise ratio: 120 dB

Frequency response: 10 – 20,000 Hz

Wow and flutter: Below measurable limit

Tuner section

FM

Tuning range: 87.5 – 108.0 MHz

Antenna (aerial) terminal:

External antenna (aerial) connector

Intermediate frequency: 10.7 MHz/450 kHz

Usable sensitivity: 9 dBf

Selectivity: 75 dB at 400 kHz

Signal-to-noise ratio: 67 dB (stereo), 69 dB (mono)

Harmonic distortion at 1 kHz: 0.5 % (stereo),

0.3 % (mono)

Separation: 35 dB at 1 kHz

Frequency response: 30 – 15,000 Hz

Fuse (10 A)

Main unit Back of the front

panel

Orient the release

keys as shown.

Hook facing

inwards.

17

MW/LW

Tuning range:

MW: 531 – 1,602 kHz

LW: 153 – 279 kHz

Antenna (aerial) terminal:

External antenna (aerial) connector

Intermediate frequency: 10.7 MHz/450 kHz

Sensitivity: MW: 30 µV, LW: 40 µV

Power amplifier section

Outputs: Speaker outputs (sure seal connectors)

Speaker impedance: 4 – 8 ohms

Maximum power output: 52 W × 4 (at 4 ohms)

General

Output:

Audio outputs terminal (sub/rear switchable)

Power antenna (aerial) relay control terminal

Power amplifier control terminal

Inputs:

Telephone ATT control terminal

Antenna (aerial) input terminal

AUX input jack (stereo mini jack)

iPod signal input terminal (dock connector)

Tone controls:

Low: ±10 dB at 60 Hz (XPLOD)

Mid: ±10 dB at 1 kHz (XPLOD)

High: ±10 dB at 10 kHz (XPLOD)

Loudness:

+4 dB at 100 Hz

+2 dB at 10 kHz

Power requirements: 12 V DC car battery

(negative ground (earth))

Dimensions: Approx. 178 × 50 × 179 mm

(7

1

/8 × 2 × 7

1

/8 in) (w/h/d)

Mounting dimensions: Approx. 182 × 53 × 162 mm

(7

1

/4 × 2

1

/8 × 6

1

/2 in) (w/h/d)

Mass: Approx. 1.3 kg (2 lb 14 oz)

Supplied accessories:

Card remote commander: RM-X151

Parts for installation and connections (1 set)

Design and specifications are subject to change

without notice.

Troubleshooting

The following checklist will help you remedy

problems you may encounter with your unit.

Before going through the checklist below, check the

connection and operating procedures.

MPEG Layer-3 audio coding technology and

patents licensed from Fraunhofer IIS and Thomson.

This product is protected by certain intellectual

property rights of Microsoft Corporation. Use or

distribution of such technology outside of this

product is prohibited without a license from

Microsoft or an authorized Microsoft subsidiary.

• Halogenated flame retardants are not used in the

certain printed wiring boards.

• Halogenated flame retardants are not used in

cabinets.

• Packaging cushions are made from paper.

General

No power is being supplied to the unit.

• Check the connection. If everything is in order, check

the fuse.

• If the unit is turned off and the display disappears, it

cannot be operated with the remote commander.

t Turn on the unit.

The power antenna (aerial) does not extend.

The power antenna (aerial) does not have a relay box.

No sound.

• The volume is too low.

• The ATT function is activated, or the Telephone ATT

function (when the interface cable of a car telephone

is connected to the ATT lead) is activated.

• The position of the fader control “FAD” is not set for

a 2-speaker system.

No beep sound.

• The beep sound is canceled (page 12).

• An optional power amplifier is connected and you are

not using the built-in amplifier.

The contents of the memory have been erased.

• The RESET button has been pressed.

t Store again into the memory.

• The power supply lead or battery has been

disconnected.

• The power supply lead is not connected properly.

Stored stations and correct time are erased.

The fuse has blown.

Makes noise when the position of the ignition

is switched.

The leads are not matched correctly with the car’s

accessory power connector.

During playback or reception, demonstration

mode starts.

If no operation is performed for 5 minutes with

“DEMO-ON” set, demonstration mode starts.

t Set “DEMO-OFF” (page 12).

The display disappears from/does not appear

in the display window.

• The dimmer is set “DIM-ON” (page 12).

• The display disappears if you press and hold (OFF).

t Press and hold (OFF) on the unit until the

display appears.

• The connectors are dirty (page 16).

The Auto Off function does not operate.

The unit is turned on. The Auto Off function activates

after turning off the unit.

t Turn off the unit.

continue to next page t

18

Error displays/Messages

Card remote commander operation is not

possible.

Make sure the insulation film has been removed

(page 4).

CD playback

The disc cannot be loaded.

• Another disc is already loaded.

• The disc has been forcibly inserted upside down or in

the wrong way.

The disc does not playback.

• Defective or dirty disc.

• The CD-Rs/CD-RWs are not for audio use (page 14).

MP3/WMA files cannot be played back.

The disc is incompatible with the MP3/WMA format

and version (page 15).

MP3/WMA files take longer to play back than

others.

The following discs take a longer time to start

playback.

– a disc recorded with a complicated tree structure.

– a disc recorded in Multi Session.

– a disc to which data can be added.

The display items do not scroll.

• For discs with very many characters, those may not

scroll.

• “A.SCRL” is set to “OFF”.

tSet “A.SCRL-ON” (page 12).

tPress and hold (DSPL) (SCRL).

The sound skips.

• Installation is not correct.

tInstall the unit at an angle of less than 45° in a

sturdy part of the car.

• Defective or dirty disc.

The operation buttons do not function.

The disc will not eject.

Press the RESET button (page 4).

Radio reception

The stations cannot be received.

The sound is hampered by noises.

• Connect a power antenna (aerial) control lead (blue)

or accessory power supply lead (red) to the power

supply lead of a car’s antenna (aerial) booster (only

when your car has built-in FM/MW/LW antenna

(aerial) in the rear/side glass).

• Check the connection of the car antenna (aerial).

• The auto antenna (aerial) will not go up.

tCheck the connection of the power antenna

(aerial) control lead.

• Check the frequency.

Preset tuning is not possible.

• Store the correct frequency in the memory.

• The broadcast signal is too weak.

Automatic tuning is not possible.

• Setting of the local seek mode is not correct.

t Tuning stops too frequently:

Set “LOCAL-ON” (page 13).

t Tuning does not stop at a station:

Set “MONO-ON” (page 13).

• The broadcast signal is too weak.

t Perform manual tuning.

During FM reception, the “ST” indication

flashes.

• Tune in the frequency accurately.

• The broadcast signal is too weak.

t Set “MONO-ON” (page 13).

An FM program broadcast in stereo is heard in

monaural.

The unit is in monaural reception mode.

t Set “MONO-OFF” (page 13).

RDS

The SEEK starts after a few seconds of

listening.

The station is non-TP or has weak signal.

t Deactivate TA (page 9).

No traffic announcements.

• Activate TA (page 9).

• The station does not broadcast any traffic

announcements despite being TP.

t Tune in another station.

PTY displays “- - - - - - - -.”

• The current station is not an RDS station.

• RDS data has not been received.

• The station does not specify the program type.

ERROR

• The disc is dirty or inserted upside down.

t Clean or insert the disc correctly.

• A blank disc has been inserted.

• The disc cannot play due to a problem.

t Insert another disc.

FAILURE

The connection of speakers/amplifiers is incorrect.

t See the installation/connections manual of this

model to check the connection.

L. SEEK +/–

The local seek mode is on during automatic tuning.

NO AF

There is no alternative frequency for the current

station.

t Press (SEEK) –/+ while the program service name

is flashing. The unit starts searching for another

frequency with the same PI (Program

Identification) data (“PI SEEK” appears).

NO INFO

Text information is not written in the MP3/WMA file.

19

If these solutions do not help improve the situation,

consult your nearest Sony dealer.

If you take the unit to be repaired because of CD

playback trouble, bring the disc that was used at the

time the problem began.

NO IPOD

No iPod connected.

tConnect iPod to dock connector.

If “NO IPOD” appears while connecting the iPod to

the dock connector, disconnect the iPod from the dock

connector, then reconnect.

NO MUSIC

The disc does not contain a music file.

tInsert a music CD in this unit.

NO NAME

A disc/track name is not written in the track.

NO TP

The unit will continue searching for available TP

stations.

OFFSET

There may be an internal malfunction.

tCheck the connection. If the error indication

remains on in the display, consult your nearest

Sony dealer.

READ

The unit is reading all track and album information on

the disc.

tWait until reading is complete and playback starts

automatically. Depending on the disc structure, it

may take more than a minute.

RESET

The CD unit cannot be operated due to a problem.

tPress the RESET button (page 4).

“ ” or “ ”

During reverse or fast-forward, you have reached the

beginning or the end of the disc and you cannot go any

further.

“ ”

The character cannot be displayed with the unit.

2

iPod ist ein in den USA und anderen Ländern

eingetragenes Markenzeichen der Apple Inc.

Wichtig!

Bitte nehmen Sie sich etwas Zeit, um

den Geräte-Pass vollständig

auszufüllen. Dieser befindet sich auf

der hinteren Umschlagseite dieser

Bedienungsanleitung.

Zur Installation und zum Anschluss siehe die

mitgelieferte Installations-/Anschlussanleitung.

Dieses Etikett befindet sich an der Unterseite

des Gehäuses.

Der Hersteller dieses Produkts ist Sony

Corporation, 1-7-1 Konan, Minato-ku, Tokio,

108-0075, Japan.

Autorisierter Vertreter für EMV und

Produktsicherheit ist die Sony Deutschland

GmbH, Hedelfinger Strasse 61, 70327 Stuttgart,

Deutschland. Für Fragen im Zusammenhang mit

Kundendienst oder Garantie wenden Sie sich

bitte an die in den separaten Kundendienst- oder

Garantieunterlagen genannten Adressen.

Entsorgung von gebrauchten

elektrischen und elektronischen

Geräten (anzuwenden in den

Ländern der Europäischen Union

und anderen europäischen Ländern

mit einem separaten Sammelsystem

für diese Geräte)

Das Symbol auf dem Produkt oder seiner Verpackung

weist darauf hin, dass dieses Produkt nicht als normaler

Haushaltsabfall zu behandeln ist, sondern an einer

Annahmestelle für das Recycling von elektrischen und

elektronischen Geräten abgegeben werden muss. Durch

Ihren Beitrag zum korrekten Entsorgen dieses Produkts

schützen Sie die Umwelt und die Gesundheit Ihrer

Mitmenschen. Umwelt und Gesundheit werden durch

falsches Entsorgen gefährdet. Materialrecycling hilft, den

Verbrauch von Rohstoffen zu verringern. Weitere

Informationen über das Recycling dieses Produkts

erhalten Sie von Ihrer Gemeinde, den kommunalen

Entsorgungsbetrieben oder dem Geschäft, in dem Sie das

Produkt gekauft haben.

Geeignetes Zubehör: Fernbedienung

Warnhinweis, wenn die Zündung Ihres

Fahrzeugs nicht über eine

Zubehörposition (ACC oder I) verfügt

Aktivieren Sie unbedingt die

Abschaltautomatik (Seite 13).

Nach dem Ausschalten wird das Gerät dann

nach der voreingestellten Zeit automatisch

vollständig abgeschaltet, so dass der

Autobatterie kein Strom mehr entzogen wird.

Wenn Sie die Abschaltautomatik nicht

aktivieren, müssen Sie jedes Mal, wenn Sie die

Zündung ausschalten, die Taste (OFF)

gedrückt halten, bis die Anzeige ausgeblendet

wird.

Entsorgung von gebrauchten

Batterien und Akkus (anzuwenden in

den Ländern der Europäischen

Union und anderen europäischen

Ländern mit einem separaten

Sammelsystem für diese Produkte)

Das Symbol auf der Batterie/dem Akku oder der

Verpackung weist darauf hin, dass diese nicht als normaler

Haushaltsabfall zu behandeln sind. Durch Ihren Beitrag

zum korrekten Entsorgen dieser Batterien/Akkus schützen

Sie die Umwelt und die Gesundheit Ihrer Mitmenschen.

Umwelt und Gesundheit werden durch falsches Entsorgen

gefährdet. Materialrecycling hilft, den Verbrauch von

Rohstoffen zu verringern.

Bei Produkten, die auf Grund ihrer Sicherheit, der

Funktionalität oder als Sicherung vor Datenverlust eine

ständige Verbindung zur eingebauten Batterie benötigen,

sollte die Batterie nur durch qualifiziertes Servicepersonal

ausgetauscht werden.

Um sicherzustellen, dass die Batterie korrekt entsorgt

wird, geben Sie das Produkt zwecks Entsorgung an einer

Annahmestelle für das Recycling von elektrischen und

elektronischen Geräten ab.

Für alle anderen Batterien entnehmen Sie die Batterie

bitte entsprechend dem Kapitel über die sichere

Entfernung der Batterie. Geben Sie die Batterie an einer

Annahmestelle für das Recycling von Batterien/Akkus ab.

Weitere Informationen über das Recycling dieses Produkts

oder der Batterie erhalten Sie von Ihrer Gemeinde, den

kommunalen Entsorgungsbetrieben oder dem Geschäft, in

dem Sie das Produkt gekauft haben.

Microsoft, Windows Media

und das Windows-Logo sind

Markenzeichen oder

eingetragene Markenzeichen

der Microsoft Corporation in den USA und/oder

anderen Ländern.

La page charge ...

Sony CDX-GT44IP Le manuel du propriétaire

Sony CDX-GT44IP Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents