Cub Cadet 25B55SD710 Manuel utilisateur

Marque: Cub Cadet

Modèle: 25B55SD710

Catégorie: Tondeuses à gazon

Taper: Manuel utilisateur

MTD LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019

Safe Operation Practices • Set-Up • Operation • Maintenance • Troubleshooting • Warranty

WARNING

READ AND FOLLOW ALL SAFETY RULES AND INSTRUCTIONS IN THIS MANUAL

BEFORE ATTEMPTING TO OPERATE THIS MACHINE.

FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY.

OperatOr’s Manual

140 cc OHV Vertical Shaft Engine

Form No. 769-18090

(September 24, 2018)

* Model 1T65 Shown

This Operator’s Manual is an important part of your new engine. It will help you prepare and maintain the engine for the best

performance. Please read and understand the contents before operating the engine.

Thank You

Model NuMber

Serial NuMber

Customer Support

Please do NOT return the machine to the retailer or dealer without first contacting the Customer Support Department.

If you have difficulty assembling this product, have questions regarding the controls, operation, or maintenance of this machine, want

to order replacement parts/attachments/accessories, or want to view an online How-To video; you can seek help from the experts. Have

your full model number and serial number ready. Choose from the options below:

◊ Visit us on the web: www.mtdproducts.com

◊ Call a Customer Support Representative at: (800) 800-7310 or (330) 220-4683

◊ Write to: MTD LLC • P.O. Box 361131 • Cleveland, OH • 44136-0019

To The Owner

Table of Contents

Safe Operation Practices ........................................ 3

Safety Symbols ........................................................ 5

Set-Up ....................................................................... 6

Controls & Features ................................................. 8

Operation ................................................................. 9

Maintenance & Adjustments .................................10

Troubleshooting .....................................................14

Replacement Parts .................................................15

EZ Start Promise† ...................................................16

Spanish .................................................................... 17

French ..................................................................... 34

Record Product Information

Before operating your new engine, please locate the model plate on the engine (shaded area in Figure below) and record the

information in the provided area below. This information will be necessary, should you seek technical support via our web site or with

your local dealer.

† Applicable to MTD Brand Auto-Choke Engines Only

Important Safe Operation Practices

WARNING! This symbol points out important safety instructions which, if not followed,

could endanger the personal safety and/or property of yourself and others. Read and follow

all instructions in this manual before attempting to operate the equipment. Failure to

comply with these instructions may result in personal injury. When you see this symbol.

HEED ITS WARNING!

DANGER! This engine was built to be operated according to the safe operation practices in

this manual. As with any type of power equipment, carelessness or error on the part of the

operator can result in serious injury. Failure to observe the following safety instructions

could result in serious injury or death.

CALIFORNIA PROPOSITION 65

WARNING! Engine Exhaust, some of its constituents, and certain vehicle components

contain or emit chemicals known to State of California to cause cancer and birth defects

or other reproductive harm.

Training

1. Read, understand and follow all instructions on the engine

and in the manual(s) before attempting to assemble and

operate. Keep this manual in a safe place for future and

regular reference and for ordering replacement parts.

2. Be familiar with all controls and their proper operation.

Know how to stop the engine and disengage them quickly.

3. Never allow children under 14 years of age to operate the

engine. Children 14 and over should read and understand

the instructions and safe operation practices in this manual

and be trained and supervised by an adult.

4. Never allow adults to operate the machine without proper

instruction.

5. Keep the area of operation clear of all persons, particularly

small children and pets. Stop machine if anyone enters the

area.

Preparation

1. Wear sturdy, rough-soled work shoes and close fitting

slacks and shirts. Loose fitting clothes or jewelry can be

caught in the moving parts. Never operate the machine in

bare feet or sandals.

2. Disengage clutch levers and shift (if equipped) into neutral

(“N”) before starting the engine.

3. Never leave the engine running while unattended.

4. Never attempt to make any adjustments while the engine

is running, except where specifically recommended in the

operator’s manual.

Safe Handling of Gasoline:

To avoid personal injury or property damage, use extreme care

in handling gasoline. Gasoline is extremely flammable and the

vapors are explosive. Serious personal injury can occur when

gasoline is spilled on yourself and/or your clothes which can

ignite. Wash your skin and change clothes immediately.

1. When adding fuel, turn engine OFF and let engine cool at

least 2 minutes before removing the gas cap.

2. Fill fuel tank outdoors or in well ventilated area.

3. Use only an approved gasoline container.

4. Never fill containers inside a vehicle or on a truck or trailer

bed with a plastic liner. Always place containers on the

ground away from your vehicle before filling.

5. If possible, remove gas-powered equipment from the truck

or trailer and refuel it on the ground. If this is not possible,

then refuel such equipment on a trailer with a portable

container, rather than from a gasoline dispenser nozzle.

6. Keep the nozzle in contact with the rim of the fuel tank or

container opening at all times until fueling is complete. Do

not use a nozzle lock-open device.

4 Section 2 — important Safe operation practiceS

7. Do not overfill fuel tank. Fill tank to full as indicated by

the fuel level indicator installed inside of the fuel tank or

marked on the tank. Do not over-fill to allow space for fuel

expansion. On some models, a fuel level indicator may NOT

be present, in this instance, fill the tank no more than 1/2

inch below the bottom of the filler neck to allow space for

fuel expansion.

8. Replace fuel cap and tighten until the cap ratchets.

9. If gasoline is spilled, wipe it off the engine and the

equipment. Move the machine to another area. Wait five

minutes before starting the engine.

10. To reduce fire hazards, keep the machine free of grass ,

leaves or other debris build up. Clean up oil or fuel spillage

and remove any fuel-soaked debris.

11. Keep gasoline away from sparks, open flames, pilot lights,

heat, and other ignition sources.

12. Never fuel equipment indoors because flammable vapors

will accumulate in the area.

13. Extinguish all cigarettes, cigars, pipes, and other sources of

ignition.

14. Check fuel line, tank, cap, and fittings frequently for cracks

or leaks. Replace if necessary.

Operation

1. When starting the engine, make sure spark plug, muffler,

and fuel cap are in place.

2. Do not crank engine with spark plug removed.

3. If fuel spills, wait until it evaporates before starting engine.

4. Allow muffler, engine cylinder, and fins to cool before

touching.

5. Keep children away from hot or running engines. They can

suffer burns from a hot muffler.

6. Remove accumulated combustibles from muffler and

cylinder area.

7. Operate equipment with all guards in place.

8. Keep hands and feet away from rotating parts.

9. Tie up long hair and remove jewelry.

10. Do not wear loose-fitting clothing, dangling drawstrings or

items that could become caught.

11. When starting the engine, pull cord slowly until resistance

is felt, then pull rapidly (if not electric start).

12. Remove all external equipment/engine loads before

starting engine.

13. Direct coupled equipment components such as, but not

limited to blades, impellers, pulleys, sprockets, etc., must

be securely attached.

Maintenance & Storage

1. Keep the engine in safe working order

2. Allow the engine to cool at least five minutes before

storing. Never tamper with safety devices. Check their

proper operation regularly.

3. Check bolts and screws for proper tightness at frequent

intervals to keep the engine in safe working condition.

Visually inspect the engine for any damage.

4. Before cleaning, repairing or inspecting; stop the

engine and make certain all moving parts have stopped.

Disconnect the spark plug wire and ground it against the

engine to prevent unintended starting.

5. Do not change the engine governor settings or over-speed

the engine. The governor controls the maximum safe

operating speed of the engine.

6. Maintain and replace safety and instruction labels as

necessary.

7. Always refer to the operator’s manual for important details

if the machine is to be stored for an extended period of

time.

8. If the fuel tank has to be drained, do this outdoors.

9. Observe proper disposal laws and regulations for gas, oil,

etc. to protect the environment.

Do not modify engine

To avoid serious injury or death, do not modify engine in any

way. Tampering with the governor setting can lead to a runaway

engine and cause it to operate at unsafe speeds. Never tamper

with factory setting of engine governor.

Notice Regarding Emissions

Engines which are certified to comply with California and federal

EPA emission regulations for SORE (Small Off Road Equipment)

are certified to operate on regular unleaded gasoline, and

may include the following emission control systems: Engine

Modification (EM), Oxidizing Catalyst (OC), Secondary Air

Injection (SAI) and Three Way Catalyst (TWC) if so equipped.

Spark Arrestor

WARNING! This machine is equipped with an

internal combustion engine and should not be used

on or near any unimproved forest-covered, brush

covered or grass-covered land unless the engine’s

exhaust system is equipped with a spark arrestor

meeting applicable local or state laws (if any).

If a spark arrestor is used, it should be maintained in effective

working order by the operator. In the State of California the

above is required by law (Section 4442 of the California Public

Resources Code). Other states may have similar laws. Federal laws

apply on federal lands.

A spark arrestor for the muffler is available through your

nearest engine authorized service dealer or contact the service

department, P.O. Box 361131 Cleveland, Ohio 44136-0019.

5Section 2 — important Safe operation practiceS

WARNING! Your Responsibility — Restrict the use of this power machine to persons who read, understand and

follow the warnings and instructions in this manual and on the machine.

SAVE THESE INSTRUCTIONS!

Safety Symbols

This page depicts and describes safety symbols that may appear on this product. Read, understand, and follow all instructions on the

machine before attempting to assemble and operate.

Symbol Description

READ THE OPERATOR’S MANUAL(S)

Read, understand, and follow all instructions in the manual(s) before attempting to

assemble and operate.

WARNING—GASOLINE IS FLAMMABLE

Allow the engine to cool at least two minutes before refueling.

WARNING— CARBON MONOXIDE

Never run an engine indoors or in a poorly ventilated area. Engine exhaust contains carbon

monoxide, an odorless and deadly gas.

WARNING— ELECTRICAL SHOCK

Do not use the engine’s electric starter in the rain.

WARNING— HOT SURFACE

Engine parts, especially the muffler, become extremely hot during operation. Allow engine

and muffler to cool before touching.

Set-Up

Gas & Oil

NOTE: The engine is shipped without gasoline or oil in the

engine. Running the engine with insufficient oil can cause

serious engine damage and void the engine warranty.

WARNING! Always keep hands and feet clear of

equipment moving parts. Do not use a pressurized

starting fluid. Vapors are flammable.

Oil Recommendations

Before starting engine, fill with motor oil, capacity is 600 ml/20

oz. Refer to viscosity chart in Figure 3-1 for oil recommendations.

Do not over-fill. Use a 4-stroke, or an equivalent high detergent,

premium quality motor oil certified to meet or exceed

U.S. automobile manufacturer’s requirements for service

classification of a minimum level SJ (higher letter ratings are

acceptable such as SL and SM grades). Motor oil will display this

designation on the container.

SAE 10W-30 is recommended for general, all temperature use. If

single viscosity oil is used, select the appropriate viscosity for the

average temperature in your area from the chart below.

-30º -20º

10w

20w

20w40, 20w50

15w40, 15w50

10w40

10w30

-10º 0º

0º 20º 40º 60º 80º 100º

10º 20º 30º 40º

-20º

(ºC)

(ºF)

Figure 3-1

1. Single Viscosity

2. Multi Viscosity

CAUTION: Do not use non-detergent oil or 2-stroke engine oil. It

could shorten the engine’s service life.

NOTE: A 5w30 synthetic oil may be used to improve start ability

for cold weather (temperatures below 40 F).

Checking Oil Level

IMPORTANT: Be sure to check the oil while on a level surface with

the engine stopped.

NOTE: Your engine may be equipped with either a short or

extended oil dipstick. Follow the appropriate instructions below

for the engine on your unit.

Short Dipstick

1. Remove the oil filler cap/dipstick and wipe the dipstick

clean. See Figure 3-2.

Figure 3-2

2. Insert the cap/dipstick into the oil filler neck, but do not

screw it in.

3. Remove the oil filler cap/dipstick. If the level is low, slowly

add oil to the upper limit on the dipstick. See Figure 3-2.

4. Replace and tighten cap/dipstick firmly before starting

engine.

NOTE: Do not overfill. Overfilling with oil may cause

smoking, hard starting, spark plug fouling, or oil saturation

of air cleaner.

7Section 3 — Set-Up

Extended Dipstick

1. Remove the oil filler cap and wipe the dipstick clean. See

Figure 3-3.

Figure 3-3

2. Insert the dipstick into the oil filler neck. Turn the dipstick a

1/4 turn into the locked position to fully seat.

3. Remove dipstick. If the level is low, slowly add oil until oil

level registers between high (H) and low (L). See Figure 3-3

inset.

4. Reinsert the dipstick into the locked position before

starting the engine.

NOTE: Do not overfill. Overfilling with oil may cause

smoking, hard starting, spark plug fouling, or oil saturation

of air cleaner.

Fuel Requirements

CAUTION: Operating the engine with E15 or E85

fuel, an oil/gasoline mixture, dirty gasoline, or

gasoline over 30 days old without fuel stabilizing

additive may result in damage to your engine’s

carburetor. Subsequent damage would not be

covered under the manufacturer’s warranty.

Use automotive gasoline (unleaded or low leaded to minimize

combustion chamber deposits) with a minimum of 87 octane.

Gasoline with up to 10% ethanol (E10) or 15% MTBE (Methyl

Tertiary Butyl Ether) can be used. Never use an oil/gasoline

mixture or dirty gasoline. Avoid getting dirt, dust, or water in the

fuel tank. DO NOT use E15 or E85 gasoline.

WARNING! Gasoline is extremely flammable and is

explosive under certain conditions.

• Refuel in a well-ventilated area with the engine stopped.

Do not smoke or allow flames or sparks in the area where

the engine is refueled or where gasoline is stored.

• Do not overfill the fuel tank. After refueling, make sure the

tank cap is closed properly and securely.

• Be careful not to spill fuel when refueling. Spilled fuel or

fuel vapor may ignite. If any fuel is spilled, make sure the

area is dry before starting the engine.

• Avoid repeated or prolonged contact with skin or

breathing of vapor.

Adding Fuel

WARNING! An adult should fuel this engine.

NEVER allow children to refuel the engine. Gasoline

(fuel) vapors are highly flammable and can explode.

Fuel vapors can spread and be ignited by a spark or

flame many feet away from engine. To prevent injury

or death from fuel fires, follow these instructions:

NOTE: Some engines may not have the fuel cap installed for

shipping purposes. To install, remove and discard the fuel tank

dust cap labeled “Discard”. Remove the bubble wrap packaging

from around the fuel cap and tighten securely.

• DO NOT use leaded fuel.

• Fuel must be fresh and clean. NEVER use fuel left over

from last season or stored for long periods.

• NEVER mix oil with fuel.

• DO NOT use fuel containing Methanol (Wood

Alcohol)

NOTE: Before refueling, allow engine to cool two minutes.

1. Clean around fuel fill before removing cap to fuel.

2. Fill tank until fuel reaches ⁄ inch below the bottom of the

filler neck to allow space for fuel expansion. Be careful not

to overfill.

3. Replace the gasoline cap and tighten securely. Wipe up

spilled fuel before starting engine. If fuel is spilled DO NOT

start engine. Move machine away from area of spillage.

Avoid creating any source of ignition until fuel vapors are

gone.

Controls and Features

Primer (If Equipped)

The primer is located on the left side of the

engine, next to the air cleaner. Pressing the

primer forces fuel directly into the engine’s

carburetor to aid in starting the engine.

Oil Drain

Removing the oil drain plug will drain the oil from the engine.

The engine is equipped with a side drain, and on select units, you

may also access a bottom drain.

Oil Fill Cap

Remove the oil fill cap to check the oil level and add oil.

Fuel Cap

Remove the fuel cap to add fuel.

NOTE: Some engines may not have the fuel cap installed for

shipping purposes. To install, remove and discard the fuel tank

dust cap labeled “Discard”. Remove the bubble wrap packaging

from around the fuel cap and tighten securely.

Starter Handle

Pull the starter handle to start the engine.

† If Equipped

Oil Drain

Air Cleaner

Oil Fill Cap

Muffler

Spark Plug

Starter Handle

Fuel Cap

Primer†

Figure 4-1

Operation

Pre-Operation Check

The engine is shipped without gasoline or oil in the engine. See

the Set-Up Section of this manual for instructions on adding oil

and gasoline.

Determine The Starting System

Before starting the engine, you must determine the type of

starting system that is on your engine. Your engine will have one

of the following types:

• Auto-Choke System: This features an automatic choke

that does not have a manual choke or primer.

• Primer System: This features a primer on the engine.

To start your engine, follow the instructions for your type of

starting system.

Note: Equipment may have remote controls. See the equipment

manual for location and operation of remote controls.

Starting the Engine

WARNING: Always keep hands and feet clear of

equipment moving parts. Do not use a pressurized

starting fluid. Vapors are flammable.

Auto-Choke System

1. Standing behind the mower, depress the blade control

handle and hold it against the upper handle. See Figure 5-1.

2. Pull the starter grip lightly until resistance is felt, then pull

rapidly to overcome compression, prevent kickback and

start engine. Repeat if necessary.

IMPORTANT: Do not allow the starter grip to snap back

against the engine. Return it gently to prevent damage to

the starter.

Primer System

1. Push primer 3 times. Wait about two seconds between

each push. See Figure 5-2. In temperature below 50°F,

prime 5 times. After the engine is warmed up, one prime

may be needed for all temperatures.

2. Standing behind the mower, squeeze and hold the blade

control against upper handle.

3. Pull the recoil starter lightly until resistance is felt, then pull

rapidly to overcome compression, prevent kickback, and

start the engine. Repeat if necessary. See Figure 5-2.

IMPORTANT: Do not allow the recoil starter to snap back

against the rope guide.

If engine does not start, it may be necessary to re-prime

the engine.

Figure 5-1

Figure 5-2

Stopping Engine

1. Release blade control or turn off the engine switch (if

equipped).

Engine Maintenance

WARNING: Shut off the engine before performing

any maintenance. To prevent accidental start-up,

disconnect the spark plug boot.

IMPORTANT: If engine must be tipped to transport equipment

or to inspect or remove grass, keep spark plug side of engine

up. Transporting or tipping engine spark plug down may cause

smoking, hard starting, spark plug fouling, or oil saturation of air

cleaner.

Periodic inspection and adjustment of the engine is essential if

high level performance is to be maintained. Regular maintenance

will also ensure a long service life. The required service intervals

and the kind of maintenance to be performed are described

in the table below. Follow the hourly or calendar intervals,

whichever occur first. More frequent service is required when

operating in adverse conditions.

WARNING: If the engine has been running, the

muffler will be very hot. Be careful not to touch the

muffler.

† Service more frequently when used in dusty areas.

†† Every season or 25 hours if operating under heavy load or high ambient temperature.

Maintenance Schedule

First 5 Hours

Each Use or

Every 5 Hrs.

Every Season

or 25 Hours

Ever y Seas on

or 50 Hours

Every Season

or 100 Hours

Service

Dates

Check Engine Oil Level

Change Engine Oil ††

P P

Check Air Cleaner

Service Air Cleaner †

Check Spark Plug

Replace Spark Plug

Clean Engine Shroud

Clean around muﬄer

Replace Fuel Filter

11Section 6 — Maintenance

Oil Service

• Check oil level regularly.

• Be sure correct oil level is maintained. Check every five

hours or daily before starting engine. See oil checking

procedure in the Operation section.

Oil Change

IMPORTANT: Be sure to check engine on a level surface with the

engine stopped. Drain the oil while the engine is still warm to

assure rapid and complete draining.

1. Remove all fuel from tank by running engine until it stops

from lack of fuel.

2. Remove drain plug and allow oil to drain into a suitable

container. See Figure 6-1.

Oil Fill Cap

Drain

Plug

* Short Dipstick

Shown

Figure 6-1

WARNING: Before tipping engine or equipment to

drain oil, drain fuel from tank by running engine

until fuel tank is empty.

3. Reinstall the drain plug and tighten it securely.

4. Refill with the recommended oil and check the oil level.

Refer to the Set-Up Section and follow the appropriate

instructions for a short or extended dipstick.

5. Reinstall the oil fill cap securely.

IMPORTANT: Used motor oil may cause skin cancer if repeatedly

left in contact with the skin for prolonged periods. Although this

is unlikely unless you handle used oil on a daily basis, it is still

advisable to thoroughly wash your hands with soap and water as

soon as possible after handling used oil.

NOTE: Please dispose of used motor oil in a manner that is

compatible with the environment. We suggest you take it in a

sealed container to your local service station for reclamation. Do

not throw it in the trash or pour it on the ground.

Air Filter Service

WARNING: Never use gasoline or low flash point

solvents for cleaning the air filter element. A fire or

explosion could result.

IMPORTANT: Never run the engine without the air filter. Rapid

engine wear will result.

NOTE: Engines with the primer starting system are equipped

with a foam air filter element. Those with the auto-choke system

have a paper element. Follow the applicable service instructions

below.

Foam Filter

1. Remove the air filter cover by turning counter-clockwise

then pulling it towards you. See Figure 6-2. Clean foam

element or replace when damaged.

Figure 6-2

2. To clean foam element, remove it from the air filter base

and wash in mild liquid detergent and water. Squeeze or

press the foam element to rinse out dirt and water. Do not

twist, this could damage or tear the foam element. Allow to

dry thoroughly before using. OIL the foam element with a

light engine oil.

12 Section 6 — Maintenance

WARNING: If the engine has been running, the

muffler will be very hot. Be careful not to touch the

muffler.

2. Visually inspect the spark plug. Discard the spark plug

if there is apparent wear, or if the insulator is cracked or

chipped. Clean the spark plug with a wire brush if it is to be

reused.

3. Measure the plug gap with a feeler gauge. Correct as

necessary by bending side electrode. See Figure 6-5. The

gap should be set to 0.030 in.

Electrode

0.030 in.

Figure 6-5

4. Check that the spark plug washer is in good condition

and thread the spark plug in by hand to prevent cross-

threading.

5. After the spark plug is seated, tighten with a spark plug

wrench to compress the washer.

NOTE: When installing a new spark plug, tighten 1/2 turn

after the spark plug seats to compress the washer. When

reinstalling a used spark plug, tighten 1/8-1/4 turn after the

spark plug seats to compress the washer.

IMPORTANT: The spark plug must be securely tightened.

An improperly tightened spark plug can become very hot

and may damage the engine.

Paper Filter

1. Remove the air filter cover by turning counter-clockwise

then pulling it towards you. See Figure 6-3.

NOTE: Paper filters cannot be cleaned and must be

replaced once a year or every 100 operating hours; more

often if used in extremely dusty conditions.

Figure 6-3

Spark Plug Service

WARNING: DO NOT check for spark with spark

plug removed. DO NOT crank engine with spark

plug removed.

To ensure proper engine operation, the spark plug must be

properly gapped and free of deposits.

1. Remove the spark plug boot and use a spark plug wrench

to remove the plug. See Figure 6-4.

Spark Plug

Spark Plug Boot

Figure 6-4

13Section 6 — Maintenance

Fuel Filter Service

The fuel filter cannot be cleaned and must be replaced once a

year or every 100 operating hours; more often if run with old

gasoline.

1. Remove all fuel from tank by running engine until it stops

from lack of fuel.

2. Remove hose clamp from fuel line and remove fuel line

from tank outlet. See Figure 6-6.

Fuel Filter

Figure 6-6

3. Pull out old fuel filter from tank outlet. Replace when dirty

or damaged.

4. Grasp new fuel filter from shouldered end and insert it

completely to the shoulder into the tank outlet. See Figure

6-6 inset.

5. Replace fuel line and hose clamp.

Clean Engine

If the engine has been running, allow it to cool for at least half

an hour before cleaning. Periodically remove dirt build-up from

engine. Clean finger guard and around muffler. Clean with a

brush or compressed air.

IMPORTANT: Do not spray engine with water to clean because

water could contaminate fuel. Using a garden hose or pressure

washing equipment can also force water into the air cleaner or

muffler opening. Water in the air cleaner will soak the paper

element, and water that passes through the element or muffler

can enter the cylinder, causing damage.

WARNING: Accumulation of debris around muffler

could cause a fire. Inspect and clean before every

use.

Storage

CAUTION: Failure to use a fuel stabilizing additive

or completely run the engine until it’s out of fuel

before off-season storage may result in damage to

your engine’s carburetor. Subsequent damage

would not be covered under the manufacturer’s

warranty.

Gasoline that will be stored longer than 30 days needs to be

pre-treated upon purchase with fuel stabilizer to prevent

gum and varnish from forming in the engines fuel and intake

system. Improper fuel storage can result in hard starting, no

starting, stalling and poor performance. If the gasoline in your

engine deteriorates during storage, you may need to have the

carburetor, and other fuel system components, serviced or

replaced.

1. Remove all fuel from tank by running engine until it stops

from lack of fuel.

WARNING: Never leave engine unattended while

running.

2. Change oil. See Oil Change section.

3. Remove spark plug and pour about 1/2 an ounce of engine

oil into cylinder. Replace spark plug and crank slowly to

distribute oil.

4. Clean debris from around engine, under finger guard, and

under, around and behind muffler. Touch up any damaged

paint, and coat other areas that may rust with a light film

of oil.

5. Store in a clean, dry and well ventilated area away from any

appliance that operates with a flame or pilot light, such

as a furnace, water heater, or clothes dryer. Also avoid any

area with a spark producing electric motor, or where power

tools are operated.

6. If possible, also avoid storage areas with high humidity,

because that promotes rust and corrosion.

7. Keep the engine level in storage. Tilting can cause fuel or

oil leakage.

Removing From Storage

1. Check your engine as described in the Pre-Operation Check

section of this manual.

2. If the fuel was drained during storage preparation, fill the

tank with fresh gasoline. If you keep a container of gasoline

for refueling, make certain it contains only fresh fuel.

Gasoline oxidizes and deteriorates over time, causing hard

starting.

3. If the cylinder was coated with oil during storage

preparation, the engine will smoke briefly at startup. This

is normal.

Troubleshooting

Problem Cause Remedy

Engine Fails to start 1. Blade control disengaged (lawn mower only).

2. Spark plug boot disconnected.

3. Fuel tank empty or stale fuel.

4. Fuel shut-off valve closed (if equipped).

5. Engine not primed (if equipped with primer).

6. Faulty spark plug.

7. Reduced fuel flow/Blocked fuel filter.

8. Engine flooded.

9. Engine not choked (if equipped with choke).

1. Engage blade control.

2. Connect wire to spark boot.

3. Fill tank with clean, fresh gasoline.

4. Turn on fuel shut-off valve.

5. Prime engine as instructed in the Operation

section.

6. Clean, adjust gap, or replace.

7. Replace fuel filter as instructed in the

Maintenance section.

8. Wait a few minutes to restart, but do not

prime.

9. Choke engine. See engine manual.

Engine runs erratic 1. Spark plug boot loose.

2. Reduced fuel flow/Blocked fuel filter.

3. Vent in gas cap plugged (if equipped).

4. Water or dirt in fuel system.

5. Dirty air cleaner.

6. Unit running with CHOKE (if equipped)

applied.

1. Connect and tighten spark plug boot.

2. Replace fuel filter as instructed in the

Maintenance section.

3. Clear vent.

4. Drain fuel tank. Refill with fresh fuel.

5. Refer to Maintenance section.

6. Push CHOKE knob in.

Engine overheats 1. Engine oil level low.

2. Air flow restricted.

1. Fill crankcase with proper oil.

2. Clean area around and on top of engine.

Occasional skips

(hesitates) at

high speed

1. Spark plug gap too close. 1. Adjust gap to .030”.

Idles poorly 1. Spark plug fouled, faulty, or gap too wide.

2. Dirty air cleaner.

1. Reset gap to .030” or replace spark plug.

2. Refer to Maintenance section.

Replacement Parts

Phone (800) 800-7310 or (330) 220-4683 to order replacement parts or a complete Parts Manual (have your full model number and

serial number ready). Parts Manual downloads are also available free of charge at www.mtdproducts.com.

Component Part Number and Description

951-14437 Spark Plug

951-14627 Air Cleaner (Foam)

951-14628 Air Cleaner (Paper)

751-15255 Fuel Cap Assembly

951-12296 Fuel Filter

GDOC-100163 Rev. B

The EZ Start Promise

Provisions of Your Limited Warranty

In addition to the other terms and conditions of the Limited

Warranty applicable to your new mower, MTD LLC (“MTD”) hereby

warrants that your mower’s engine will start on the first or second

attempt by an able-bodied adult (subject to the limitations

described below) for the duration of the manufacturer’s limited

warranty applicable to your product. If the engine on your mower

fails to conform to this limited warranty, MTD will cover the cost

of parts and labor associated with any adjustments and/or repairs

necessary to return your engine to its warranted condition. In

order to make a claim under these provisions of your warranty, you

must bring the product and proof of purchase to an authorized

MTD service provider. In many cases, the retailer who sold you

your mower is not equipped to provide warranty service, so please

locate the authorized service dealer nearest you by either calling

the phone number provided in your Operators Manual or looking

up an authorized service dealer on-line at www.mtdproducts.com.

Items and Conditions Not Covered

The EZ Start Promise does not cover and/or apply to the following:

• Cost of regular maintenance service or parts, such as filters,

fuel, lubricants, oil changes, spark plugs, air filter, blade

sharpening, worn blades, cable/linkage adjustments, or brake

and clutch adjustments

• Transportation costs to and from an authorized MTD service

provider

• Any engine used for commercial, rental, institutional,

governmental, or non-residential applications

• Any product or part that has been altered or misused or

required replacement or repair due to misuse, accidents, or

lack of proper maintenance

• Repairs necessary due to improper battery care, electrical

supply irregularities, or failure to properly prepare the mower

prior to any period of non-use over three months

• Pickup and/or delivery charges

• Operational misuse, neglect, accidents, unauthorized repairs

or attempted repairs of the engine or its components by

anyone other than an authorized MTD service provider.

• Repairs or adjustments to correct starting difficulties due to

any of the following: failure to follow proper maintenance

procedures — rotary mower blade striking an object —

contaminants in the fuel system — improper fuel or fuel/oil

mixture (consult your Operator’s Manual if in doubt) — failure

to drain the fuel system prior to any period of non-use over

three months.

• Any starting problem which results from the use of

inappropriate fuels, lubricants, or additives.

• Special conditions or circumstances that normally require

more than two pulls to start, specifically: 1) First start-up

following your initial purchase, 2) first time starts after

extended period(s) of non-use over one month or seasonal

storage, 3) cool temperature starts such as those found in

early spring and late autumn, and 4) difficult starting that

results from the operator’s failure to follow the proper

starting procedures identified in the Operator’s Manual. If

you are having difficulty starting your unit, please check the

Operator’s Manual to ensure that you are using the correct

starting procedures. This can save an unnecessary visit to a

Service Dealer.

Owner Responsibilities

You must maintain your mower (including its engine) by following

the maintenance procedures and starting instructions described

in the Operator’s Manual. Such routine maintenance, whether

performed by a dealer or by you, is at your expense. In addition,

please retain your proof of purchase and service receipts as these

may be required to validate a claim.

General Conditions

An authorized MTD service provider using approved replacement

parts must perform all repairs covered by the EZ Start Promise.

Repair by an MTD authorized service dealer is your sole remedy

under this warranty. MTD is not liable for indirect, incidental, or

consequential damages in connection with the use of the products

covered by these warranties, including any cost or expense of

providing substitute equipment or service during reasonable

periods of malfunction or non-use pending completion of repairs

under this warranty.

Some states do not allow exclusions of incidental or consequential

damages, or limitations on how long an implied warranty lasts, so

certain exclusions and limitations may not apply to you.

MTD LLC. APARTADO POSTAL 361131 CLEVELAND, OHIO 44136-0019

Medidas importantes de seguridad • Conﬁguración • Funcionamiento • Mantenimiento

• Solución de problemas • Garantía

ADVERTENCIA

LEA Y RESPETE TODAS LAS NORMAS DE SEGURIDAD E INSTRUCCIONES INCLUIDAS EN ESTE

MANUAL ANTES DE PONER EN FUNCIONAMIENTO ESTA MÁQUINA.

SI NO RESPETA ESTAS INSTRUCCIONES PUEDE PROVOCAR LESIONES PERSONALES.

Manual del OperadOr

Motor de 140 cc con eje vertical y válvulas en cabeza

* 1T65 Modelo que ﬁgura

Este Manual del Operador es una parte importante de su nuevo motor. Le ayudará a preparar y mantener la unidad para obtener los

mejores resultados. Antes de operar el motor lea cuidadosamente y comprenda todo el manual.

Gracias

NúMero de Modelo

NúMero de Serie

Asistencia al Cliente

Por favor, NO devuelva la unidad al minorista o distribuidor sin ponerse en contacto primero con el Departamento de

Asistencia al Cliente.

En caso de tener problemas para montar este producto o de tener dudas con respecto a los controles, funcionamiento o

mantenimiento del mismo, puede solicitar la ayuda de expertos. Elija entre las opciones que se presentan a continuación:

◊ Visite nuestro sitio web en www.mtdproducts.com

◊ Llame a un representante de Asistencia al Cliente al (800) 800-7310 ó (330) 220-4683

◊ Escríbanos a MTD LLC • P.O. Box 361131 • Cleveland, OH • 44136-0019

Al propietario

Índice

Medidas importantes de seguridad ...................... 3

Conﬁguración .......................................................... 6

Controles y Características ..................................... 8

Funcionamiento ...................................................... 9

Mantenimiento y Ajustes .......................................10

Solución de problemas ..........................................14

Piezas de Reemplazo .................15 (Manual inglés)

EZ Start Promise† ...................................................15

Registro de información de producto

Antes de operar su motor nuevo, por favor localice su placa de modelo en el motor (Área sombreada en la figura a continuación) y

registre la información en el área situada a continuación. Si tiene que solicitar soporte técnico a través de nuestro sitio web o de un

distribuidor de servicio local, necesitará esta información.

† Aplicable a las MTD Marca Auto-Choke Sólo Motores

Medidas importantes de seguridad

¡ADVERTENCIA! La presencia de este símbolo indica que se trata de instrucciones de

seguridad importantes que debe respetar para evitar poner en riesgo su seguridad personal

y/o material y la de los demás. Lea y siga todas las instrucciones de este manual antes de

poner en funcionamiento este equipo. Si no respeta estas instrucciones puede provocar

lesiones personales. Cuando vea este símbolo. TENGA EN CUENTA LA ADVERTENCIA.

¡PELIGRO! Esta motor está diseñada para ser utilizada respetando las normas de seguridad

contenidas en este manual. Al igual que con cualquier tipo de equipo motorizado, un descuido o

error por parte del operador puede producir lesiones graves. De no respetar las instrucciones de

seguridad siguientes se pueden producir lesiones graves o la muerte.

PROPOSICIÓN 65 DE CALIFORNIA

¡ADVERTENCIA! El escape del motor de este producto, algunos de sus componentes y

algunos componentes del vehículo contienen o liberan sustancias químicas que el estado

de California considera que pueden producir cáncer, defectos de nacimiento u otros

problemas reproductivos.

Capacitación

1. Lea, entienda y cumpla todas las instrucciones incluidas en

el motor y en los manuales antes de montarlo y utilizarlo.

Guarde este manual en un lugar seguro para consultas

futuras y periódicas, así como para solicitar repuestos.

2. Familiarícese con todos los controles y con el uso adecuado

de los mismos. Sepa cómo detener el motor y desactivar

los controles rápidamente.

3. No permita nunca que los niños menores de 14 años

utilicen este motor. Los niños de 14 años en adelante deben

leer y entender las instrucciones de operación y normas

de seguridad contenidas en este manual y en el motor y

deben ser entrenados y supervisados por un adulto.

4. Nunca permita que los adultos operen la máquina sin

recibir antes la instrucción apropiada.

5. Mantenga el área de operación despejada de personas,

particularmente de niños pequeños y mascotas. Detenga la

máquina si alguien se acerca.

Preparativos

1. Utilice zapatos de trabajo resistentes, de suela fuerte, así

como pantalones y camisas ajustados. Las prendas sueltas

y las alhajas se pueden enganchar en las piezas móviles.

Nunca opere la máquina descalzo o con sandalias.

2. Antes de arrancar el motor, desenganche las palancas del

embrague y desplácelas (en caso de haber) a la posición

neutral (“N”).

3. Nunca deje el motor en marcha sin vigilancia.

4. Nunca intente realizar ajustes mientras el motor está

en marcha, excepto en los casos específicamente

recomendados en el manual del operador.

Manejo seguro de la gasolina:

Para evitar lesiones personales o daños materiales sea

sumamente cuidadoso al manipular la gasolina. La gasolina es

sumamente inflamable y sus vapores pueden causar explosiones.

Si se derrama gasolina encima o sobre la ropa se puede lesionar

gravemente ya que se puede incendiar. Lávese la piel y cámbiese

de ropa de inmediato.

1. Cuando agregue combustible, APAGUE el motor y déjelo

enfriar por lo menos 2 minutos antes de sacar la tapa del

combustible.

2. Llene el tanque de combustible al aire libre o en un área

bien ventilada.

3. Utilice sólo los recipientes para gasolina autorizados.

4. Nunca llene los recipientes en el interior de un vehículo

o camión o caja de remolque con recubrimiento plástico.

Coloque siempre los recipientes en el piso y lejos del

vehículo antes de llenarlos.

5. Si es posible, retire el equipo a gasolina del camión o

remolque y llénelo en el suelo. Si esto no es posible, llene el

equipo en un remolque con un contenedor portátil, en vez

de con una boquilla dispensadora de gasolina.

6. Mantenga la boquilla de llenado en contacto con el

borde del depósito de combustible o con la abertura del

recipiente en todo momento, hasta terminar la carga. No

utilice un dispositivo para abrir/cerrar la boquilla.

4 Sección 2 — MedidaS iMportanteS de Seguridad

7. No llene demasiado el tanque de combustible. Llene

el tanque completo indicado por el indicador de nivel

de combustible instalado en el interior del depósito de

combustible o marcado en el depósito. No más de relleno

para dejar espacio para la expansión del combustible. En

algunos modelos, un indicador de nivel de combustible

no puede estar presente, en este caso, llenar el tanque sin

pulgada más de 1 / 2 por debajo de la parte inferior de la

boca de llenado para dejar espacio para la expansión del

combustible.

8. Reemplace la tapa de combustible y apriete hasta que la

tapa de trinquetes.

9. Limpie el combustible que se haya derramado sobre el

motor y el equipo. Traslade la máquina a otra zona. Espere

cinco minutos antes de encender el motor.

10. Para reducir el riesgo de incendio mantenga la máquina

limpia de pasto, hojas y de la acumulación de otros

desechos. Limpie los derrames de aceite o combustible y

saque todos los residuos embebidos de combustible.

11. Mantenga la gasolina alejada de chispas, llamas expuestas,

llamas piloto, calor, y otras fuentes de ignición.

12. Nunca cargue combustible en el equipo en interiores

porque se acumulan vapores inflamables en el área.

13. Apague todos los cigarrillos, cigarros, pipas y otras fuentes

de ignición.

14. Verifique frecuentemente la línea de combustible, el

depósito, el tapón, y los accesorios buscando rajaduras o

pérdidas. Reemplácelos de ser necesario.

Funcionamiento

1. Al arrancar el motor, asegúrese de que la bujía, el silenciador

y la tapa del combustible están en su lugar.

2. No dé arranque al motor si no está la bujía de encendido.

3. Si se derrama combustible, espere hasta que se evapore

antes de encender el motor.

4. Permita que el silenciador, el cilindro del motor, y las aletas

se enfríen antes de tocarlos.

5. Mantenga a los niños alejados de los motores en marcha o

calientes. Pueden sufrir quemaduras por el contacto con un

silenciador caliente.

6. Extraiga el combustible acumulado en el silenciador y el

cilindro.

7. Haga funcionar el equipo con todos los protectores

colocados.

8. Mantenga las manos y los pies alejados de las piezas

giratorias.

9. Átese el cabello si lo lleva largo y no use alhajas.

10. No use ropa demasiado holgada, con cordones colgantes o

partes que se puedan enganchar.

11. Para encender el motor, jale de la cuerda lentamente hasta

que sienta resistencia, luego jale rápidamente (Si no es de

arranque eléctrico).

12. Antes de arrancar el motor, retire todos los equipos

externos/cargas del motor.

13. Los componentes del equipo acoplados directamente,

tales como por ejemplo, cuchillas, rotores, poleas, ruedas

dentadas, etc, deben estar firmemente conectados.

Mantenimiento y Almacenamiento

1. Mantenga el motor en condiciones seguras de

funcionamiento.

2. Deje que motor se enfríe por lo menos cinco minutos antes

de guardarla. Nunca altere los dispositivos de seguridad.

Controle periódicamente que funcionen correctamente.

3. Controle frecuentemente que todos los pernos y

tornillos estén bien ajustados para mantener el motor

en condiciones seguras de funcionamiento. Inspeccione

visualmente el motor para determinar si está dañado.

4. Antes de limpiar, reparar o revisar el motor, deténgalo y

asegúrese que todas las partes móviles se hayan detenido.

Desconecte el cable de la bujía y póngalo haciendo

masa contra el motor para evitar que se encienda

accidentalmente.

5. No cambie la configuración del regulador del motor ni lo

opere a sobrevelocidad. El regulador del motor controla la

velocidad máxima segura de funcionamiento del motor.

6. Mantenga y reemplace las etiquetas de seguridad e

instrucciones según sea necesario.

7. Consulte siempre el manual del operador para conocer la

información importante relativa al almacenamiento de la

máquina durante un plazo prolongado.

8. Si debe vaciar el tanque de combustible, hágalo al aire libre.

9. Respete las normas referentes a la disposición correcta y las

reglamentaciones sobre gasolina, aceite, etc. para proteger

el medio ambiente.

Aviso referido a emisiones

Los motores que están certificados y cumplen con las regulaciones

de emisiones federales EPA y de California para SORE (Equipos

pequeños todo terreno) están certificados para operar con

gasolina común sin plomo y pueden incluir los siguientes sistemas

de control de emisiones: Modificación de motor (EM) y catalizador

de tres vías (TWC) si están equipados de esa manera.

Amortiguador de chispas

¡ADVERTENCIA! Esta máquina está equipada con

un motor de combustión interna y no debe ser

utilizada en un terreno agreste cubierto por bosque,

malezas o hierba ni en las proximidades del mismo,

excepto si el sistema de escape del motor está

equipado con un amortiguador de chispas que

cumpla con las leyes locales o estatales

correspondientes, en caso de haberlas.

Si se utiliza un amortiguador de chispas el operador lo debe

mantener en condiciones de uso adecuadas. En el Estado de

California las medidas anteriormente mencionadas son exigidas

por ley (Artículo 4442 del Código de Recursos Públicos de

California). Es posible que existan leyes similares en otros estados.

Las leyes federales se aplican en territorios federales.

Puede conseguir el amortiguador de chispas para el silenciador a

través de su distribuidor de mantenimiento de motores autorizado

más cercano o poniéndose en contacto con el departamento de

servicios, Apartado Postal 361131 Cleveland, Ohio 44136-0019.

La page charge ...

Cub Cadet 25B55SD710 Manuel utilisateur

Marque: Cub Cadet

Modèle: 25B55SD710

Catégorie: Tondeuses à gazon

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Cub Cadet 25B55SD710 User manual
español: Cub Cadet 25B55SD710 Manual de usuario

Documents connexes

Cub Cadet 31PS2S5C710 Manuel utilisateur

Cub Cadet 25B55SD710 Manuel utilisateur

Cub Cadet 25B55SD710 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents