GE 3800 Manuel utilisateur

TINSEA471JBRZ 49-7548 05-06 JR

Air Conditioners

Safety Instructions . . . . . . . . . . .2

Operating Instructions

Air Direction . . . . . . . . . . . . . . . .4

Auxiliary Controls . . . . . . . . . .5–9

Controls . . . . . . . . . . . . . . . . . . . .3

To Remove the Room Cabinet . .4

Vent Control . . . . . . . . . . . . . . . .4

Care and Cleaning

Air Filters . . . . . . . . . . . . . . . . . .11

Base Pan . . . . . . . . . . . . . . . . . .10

Outdoor Coils . . . . . . . . . . . . . .10

Room Cabinet and Case . . . . . .10

Vent Filter . . . . . . . . . . . . . . . . .10

Installation Instructions

Electrical Supply . . . . . . . . .14–17

Installing the Zoneline . . . .18, 19

Optional Drain Kit . . . . . . . . . .20

Preparation . . . . . . . . . . . . . . . .12

Replacing an Existing Unit? . . .13

Troubleshooting Tips . . . .21, 22

Normal Operating Sounds . . . .23

Consumer Support

Consumer Support . . .Back Cover

Product Registration . . . . . .25, 26

Warranty . . . . . . . . . . . . . . . . . .27

Heat/Cool Model 2800

Heat Pump Model 3800

Owner’s Manual and

Installation Instructions

ge.com

Write the model and serial

numbers here:

Model # ____________________

Serial # ____________________

Find these numbers on a label

behind the room cabinet on the

base pan.

Zoneline

®

Español

For a Spanish version of this

manual, visit our Website at

ge.com.

Para consultar una version en

español de este manual de

instrucciones, visite nuestro

sitio de internet ge.com.

Française

For a French version of this

manual, visit our Website at

www.electromenagersge.ca.

Pour une version française de

ce manuel d'utilisation, veuillez

visiter notre site web à l’adresse

www.electromenagersge.ca.

Consumer Support Troubleshooting Tips Care and Cleaning Operating Instructions Safety Instructions

IMPORTANT SAFETY INFORMATION.

READ ALL INSTRUCTIONS BEFORE USING.

WARNING!

For your safety, the information in this manual must be followed to minimize the risk of fire or

explosion, electric shock, or to prevent property damage, personal injury, or loss of life.

■ This Zoneline must be properly

installed in accordance with the

Installation Instructions before it is

used. See the Installation Instructions

in the back of this manual.

■ Replace immediately all electric service

cords that have become frayed or

otherwise damaged. A damaged power

supply cord must be replaced with a

new power supply cord obtained from

the manufacturer and not repaired.

Do not use a cord that shows cracks

or abrasion damage along its length

or at either the plug or connector end.

■ Unplug or disconnect the Zoneline at

the fuse box or circuit breaker before

making any repairs.

NOTE: We strongly recommend that any

servicing be performed by a qualified

individual.

Replacing an existing unit?

For details, see the Installation

Instructions in this manual.

SAFETY PRECAUTIONS

READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.

SAVE THESE INSTRUCTIONS

2

Quick Heat Recovery

Activates each time the thermostat is

switched from STOP or a COOL mode to a HEAT

mode. Electric heaters are energized until the

thermostat set point is reached. On heat pump

models, the heat pump operation will resume

at the next call for heat.

Safety Instructions Operating Instructions Care and Cleaning Troubleshooting Tips Consumer Support

3

Controls

Temp Control

The temp control is used to maintain the

room temperature. The compressor will

cycle on and off to keep the room at the

same comfort level. When you turn the

knob to COOLER (blue), the indoor air

will become cooler. Turn the knob to

WARMER (red) and the indoor air will

become warmer.

3800 Series only

When the outdoor temperature is lower

than 20°F, heat is provided by the electric

heater in the air conditioner instead of by

the heat pump.

Mode Control

HIGH COOL and LOW COOL provide cooling

with different fan speeds.

HIGH HEAT and LOW HEAT provide heating

with different fan speeds.

LOW FAN or HIGH FAN provides air

circulation and filtering without cooling

or heating.

NOTE: If you move the switch from a cool or heat

setting to STOP or to a fan setting, the unit has an

automatic 3-minute delay before allowing the

compressor to restart in the cool or heat mode.

TEMP CONTROL MODE CONTROL

About the controls on your Zoneline. ge.com

About Your Heat Pump (3800 Series only)

Heat pumps can save money by removing heat

from the outside air—even when the outside

temperature is below freezing—and releasing

that heat indoors.

To get the best performance from your heat

pump, don’t change the room thermostat very

often. Raising the heat setting 2–3 degrees will

cause the Zoneline to use its electric heating

elements in order to reach the new temperature

setting quickly.

There is a three minute minimum compressor

run time at any setting to prevent short cycling.

The indoor fan motor starts before the

compressor and stops after the compressor

cycles off.

The electric heating elements use much

more electricity than heat pumps and cost

more to operate.

Consumer Support Troubleshooting Tips Care and Cleaning Operating Instructions Safety Instructions

Ventilation Control

The ventilation control lever is located at the

upper left side of the Zoneline unit, behind

the room cabinet.

When set at the closed position, only the air

inside the room is circulated and filtered.

When set at the open position, some outdoor

air will be drawn into the room. This will

reduce the heating or cooling efficiency.

Energy Tip: Keep the vent control at the closed

position. The room air will be filtered and

circulated.

NOTE: Two shipping screws must be removed from the

vent door before use. See the Installation Instructions

in the back of this manual.

Air Direction

To adjust the air direction, remove the room

cabinet. Remove the 7 louver screws that hold

the louver insert in place. Flip the louver insert

180°, replace the screws and the room cabinet.

Remove the room cabinet and flip the louver

insert to change the air direction.

4

Other features of your Zoneline.

To Remove the Room Cabinet

Additional controls are located behind the

room cabinet.

To remove: Pull out at the bottom to release it

from the tabs (1). Then lift up (2).

To replace: Place the tabs over the top rail (1).

Push inward at the bottom until it snaps into

place (2).

Vent

control

(shown in

middle

position)

Open

position

Closed

position

Louver screws

5

Auxiliary Controls on your Zoneline. ge.com

Auxiliary Controls—Dip Switches

The auxiliary dip switch controls are located

behind the room cabinet, through an opening

in the control panel.

Remove the room cabinet. See the To Remove the

Room Cabinet section.

The owner is responsible for checking switches

and ensuring they are in the desired position.

HIGH

COOL

1 2 3 4 5 6 1 2 3 4 5 67 8

UP

DOWN

UP

DOWN

ALLI

2

R (All Electric Heat)

(3800 Series models only)

C: FAN CN (Cooling–Smart Fan)

H: FAN CY (Heating–Smart Fan)

CLASS 2 (Remote Thermostat)

LOAD SHEDDING (CDC)

FREEZ Sen (Freeze Sentinel)

CONST FAN (Constant ON Fan)

No Function (Reserved for future use)

TL1 (H) (Temp. Limit 1–Heat)

TL2 (H) (Temp. Limit 2–Heat)

TL3 (H) (Temp. Limit 3–Heat)

TL1 (C) (Temp. Limit 1–Cool)

TL2 (C) (Temp. Limit 2–Cool)

TL3 (C) (Temp. Limit 3–Cool)

7 8

Heat Sentinel

HEAT BOOST

(3800 Series models only)

Safety Instructions Operating Instructions Care and Cleaning Troubleshooting Tips Consumer Support

All Electric Heat

This electric heat option functions only on the

3800 Series models. When this switch is enabled

(UP), heat pump operation is locked out, causing

the unit to provide only electric resistance heat.

Cooling—Smart Fan

When this switch is enabled (UP), it allows the

indoor fan to cycle on/off with the compressor.

When this switch is disabled (DOWN), it allows

the indoor fan to run continuously.

Heating—Smart Fan

When this switch is enabled (UP), it allows the

indoor fan to run continuously. When this

switch is disabled (DOWN), it allows the indoor

fan to cycle on/off with the heat pump or

heater operation.

ALLI

2

R (All Electric Heat)

C: FAN CN (Cooling–Smart Fan)

H: FAN CY (Heating–Smart Fan)

Dip Switches

Access Cover

6

Auxiliary controls on your Zoneline.

Remote Thermostat—Class 2

When this switch is enabled (UP), it allows the

unit to operate with a Class 2 Remote Control

Wall Thermostat. The unit controls are disabled.

Load Shedding (Central Desk Control)

This feature is active only if the unit is in

CDC mode. When this switch is enabled (UP),

the indoor fan can be turned ON or OFF with

the unit controls.

Freeze Sentinel

When this switch is enabled (UP), it turns OFF

the freeze sentinel protection feature. With the

switch disabled (DOWN), the freeze sentinel is

activated, which automatically provides heat

without user interface. This helps to prevent

plumbing damage by turning the heater and

indoor fan ON at 41°F and OFF at 46°F.

Constant ON Fan

When this switch is enabled (UP), it allows the

indoor fan to run continuously, at high speed,

even if the unit is in the STOP position.

Consumer Support Troubleshooting Tips Care and Cleaning Operating Instructions Safety Instructions

CLASS 2 (Remote Thermostat)

LOAD SHEDDING (CDC)

FREEZE Sen (Freeze Sentinel)

CONST FAN (Constant

ON Fan)

7

ge.com

Temperature Limiting

Temperature limiting can reduce energy costs

by limiting the lowest temperature that can be

set for cooling and the highest temperature that

can be set for heating. Temperature limiting is

controlled by the second six auxiliary switches.

The first three switches are used to select the

cooling limits, and the remaining three switches

are used to control the heating limits. This

feature is not available with the Remote

Thermostat—Class 2.

HIGH

COOL

1 2 3 4 5 6 1 2 3 4 5 67 8

UP

DOWN

UP

DOWN

TL1 (C) (Temp. Limit 1–Cool)

TL2 (C) (Temp. Limit 2–Cool)

TL3 (C) (Temp. Limit 3–Cool)

7 8

HIGH

COOL

1 2 3 4 5 6 1 2 3 4 5 67 8

UP

DOWN

UP

DOWN

TL1 (H) (Temp. Limit 1–Heat)

TL2 (H) (Temp. Limit 2–Heat)

TL3 (H) (Temp. Limit 3–Heat)

7 8

Temperature limiting during COOL mode

(all temperatures shown in °F)

UP DOWN Minimum Maximum

NONE 1, 2, 3 60° 85°

1 2, 3 64° 85°

1, 2 3 66° 85°

2 1, 3 68° 85°

2, 3 1 70° 85°

1, 2, 3 NONE 72° 85°

1, 3 2 74° 85°

3 1, 2 76° 85°

Temperature limiting during HEAT mode

(all temperatures shown in °F)

UP DOWN Minimum Maximum

NONE 4, 5, 6 60° 85°

4 5, 6 60° 80°

4, 5 6 60° 78°

5 4, 6 60° 76°

5, 6 4 60° 74°

4, 5, 6 NONE 60° 72°

4, 6 5 60° 70°

6 4, 5 60° 65°

Safety Instructions Operating Instructions Care and Cleaning Troubleshooting Tips Consumer Support

Heat Sentinel

When this switch is enabled (UP), it turns ON

the heat sentinel protection feature. With the

switch disabled (DOWN), the heat sentinel is

de-activated. This feature automatically provides

cooling without user interface. This helps to

prevent an excessively hot room by turning the

air conditioner ON at 85°F and OFF at 80°F.

Heat Sentinel

Heat Boost (AZ3800 only)

When this switch is enabled (UP) and outdoor

temperatures are between 20°F and 46°F, heat

pump only operation is locked out. This setting is

used to provide supplementary heat to the heat

pump operation in conditions where the heat

pump only operation is not sufficient to maintain

a consistent, comfortable room temperature.

NOTE: This is an auxiliary switch for AZ2800 models and

must remain in the (DOWN) position.

BOOST (Heat Boost Operation)

8

Consumer Support Troubleshooting Tips Care and Cleaning Operating Instructions Safety Instructions

Auxiliary controls on your Zoneline.

Auxiliary Controls—Terminal Connections

The auxiliary controls are located behind the

room cabinet beneath the access cover.

Remove the room cabinet. See the

To Remove the Room Cabinet section.

Remove the screw from the access cover.

To make wiring connections, insert the wires

into the bottom of the terminals and tighten

screws securely.

After all desired connections have been

made, replace the access cover and room

cabinet.

The owner is responsible for making all

connections and setting the appropriate

dip switches.

CAUTION:

Improper wiring may damage the Zoneline

electronics. No common busing is permitted.

Damage or erratic operation may result.

A separate wire pair must be run from each

separate controlling switch to each individual

Zoneline.

4

3

2

1

External Fan

Central Desk Control

Common - Ground

White - Heater

Yellow - Compressor

Black - Solenoid

Green - High Speed Fan

Green - Low Speed Fan

Red - 24 V AC only

9

Safety Instructions Operating Instructions Care and Cleaning Troubleshooting Tips Consumer Support

ge.com

External Fan (Obtained locally)

When connected, an auxiliary or external fan

can be controlled with the indoor fan motor

on the Zoneline. Connections provide 24 V AC

to energize a remote relay, turning on the

external fan.

External Fan

Central Desk Control

When connected, the unit can be turned ON

or OFF with a switch located at the Central

Control Panel. A separate wire pair must be

run from each separate controlling switch to

each individual Zoneline.

Central Desk Control

Remote Thermostat

When connected, the unit will be controlled

by a remote thermostat.

NOTE: The number 4 dip switch must be in the

enabled (UP) position to activate the remote

thermostat. (See the installation instructions

supplied with the remote thermostat).

IMPORTANT:

The Zoneline thermostat connections

provide 24 V AC only.

If using a digital/electronic wall thermostat,

you must set it to the 24 V AC setting.

See the Installation Instructions for the

wall thermostat.

CAUTION:

Damage to a wall thermostat or to the

Zoneline electronics can result from improper

connections. Special care must be used in

connecting the wires. No line voltage

connections should be made to any circuit.

Isolate all wires in building from line voltage.

Common - Ground

White - Heater

Yellow - Compressor

Black - Solenoid

Green - High Speed Fan

Green - Low Speed Fan

Red - 24 V AC only

Consumer Support Troubleshooting Tips Care and Cleaning Operating Instructions Safety Instructions

10

Care and cleaning.

Base Pan

In some installations, dirt or other debris may be

blown into the unit from the outside and settle in

the base pan (the bottom of the unit).

In some areas of the United States, a “gel-like” or

“slime-like” substance may be seen in the base pan.

Check it periodically and clean, if necessary.

Ventilation Filter

If the vent door is open, clean the vent filter twice a year

or as required.

Turn the Zoneline off before cleaning.

To remove the vent filter:

■ Remove the room cabinet. See the To Remove

the Room Cabinet section.

■ Remove the four screws securing the unit

flanges to the case.

■ Slide the unit from the wall case.

■ Grasp the vent filter tab and pull the filter out

by sliding it to the right.

To clean the vent filter:

■ Run water through the filter from the

back side.

■ Dry thoroughly before replacing.

Outdoor Coils

The coils on the outdoor side of the Zoneline

should be checked regularly. If they are clogged

with dirt or soot, they may be professionally

steam cleaned, a service available through your

GE service outlet. You will need to remove the

unit to inspect the coils because the dirt

buildup occurs on the inside.

Clean the outside coils regularly.

Room Cabinet and Case

Turn the Zoneline off and disconnect the

power supply.

To clean, use water and a mild detergent.

Do not use bleach or abrasives. Some commercial

cleaners may damage the plastic parts.

Coils

Grille

Safety Instructions Operating Instructions Care and Cleaning Troubleshooting Tips Consumer Support

11

To maintain optimum performance, clean the filters at least every 30 days.

Air Filters

Turn the Zoneline off before cleaning.

The most important thing you can do to

maintain the Zoneline is to clean the filter

at least every 30 days. Clogged filters reduce

cooling, heating and air flow.

Keeping these filters clean will:

■ Decrease cost of operation.

■ Save energy.

■ Prevent clogged heat exchanger coils.

■ Reduce the risk of premature component

failure.

To clean the air filters:

■ Vacuum off the heavy soil.

■ Run water through the filters from the

back side.

■ Dry thoroughly before replacing.

NOTE: The air filters are interchangeable

and will fit in either the right or left side.

To remove the air filters:

To replace the air filters:

CAUTION: Do not operate the

Zoneline without the filters in place. If a filter

becomes torn or damaged, it should be replaced

immediately.

Operating without the filters in place or with

damaged filters will allow dirt and dust to reach

the indoor coil and reduce the cooling, heating,

airflow and efficiency of the unit.

Replacement filters are available from your

salesperson, GE dealer, GE Service and Parts

Center or authorized Customer Care

®

servicers.

Dirty filter—Needs cleaning Clogged filter—Greatly

reduces cooling, heating

and airflow.

FRONT

Pull up

Push down

2 Air filters

ge.com

BEFORE YOU BEGIN

Installation Zoneline Air

Instructions Conditioners

Read these instructions completely and carefully.

•

IMPORTANT – Save these

instructions for local inspector’s use.

•

IMPORTANT – Observe all

governing codes and ordinances.

• Note to Installer – Be sure to leave these

instructions with the owner.

•

Note to Owner – Keep these instructions for

future reference.

• Proper installation is the responsibility of the

installer.

• Product failure due to improper installation is not

covered under the Warranty.

Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: ge.com

IMPORTANT ELECTRICAL

SAFETY—READ CAREFULLY

CAUTION:

• Follow the National Electrical Code (NEC) or local

codes and ordinances.

• For personal safety, this Zoneline must be properly

grounded.

• Protective devices (fuses or circuit breakers)

acceptable for Zoneline installations are specified

on the nameplate of each unit.

• Do not use an extension cord with this unit.

• Aluminum building wiring may present special

problems—consult a qualified electrician.

• When the unit is in the OFF position, there is

still voltage to the electrical controls.

• Disconnect the power to the unit before

servicing by:

1 Removing the power cord (if it has one) from

the wall receptacle.

OR

2 Removing the branch circuit fuses or turning

the circuit breakers off at the panel.

Phillips screwdriver

TOOLS YOU WILL NEED

12

ZONELINE COMPONENTS

Exterior grille/louver**

** Shipped with the Zoneline unit

** Check the “Essential Elements” list on the unit

Wall case**

Zoneline unit

Room cabinet*

Power supply kit**

13

Installation Instructions

Use the correct wall case

This unit is designed to be installed in a GE plastic or

insulated metal wall case. This minimizes condensation

from forming on the room side of the case.

If the current wall case is not insulated, you can reduce

the possibility of condensation forming by installing

insulation kit RAK901L, available where you purchased

the unit.

NOTE: There are several extra holes in the unit side

flanges for installation in wall cases other than GE.

To avoid damaging the flange insulation, the installer

should use an awl or other sharp tool to puncture the

insulation in the appropriate holes before installing

the attachment screws.

Use the correct outdoor grille

You should use the outdoor grilles shown on the

“Essential Elements” label on the top of the unit.

• If an existing grille is not replaced, capacity and

efficiency will be reduced and the unit may fail to

operate properly or fail prematurely. A deflector kit,

RAK40, may be used with grilles that were not

designed for your new GE Zonelines. The RAK40

contains air deflectors and gaskets that mount to the

unit to direct the hot exhaust air away from the air

intake to allow the unit to function properly. The

grille must have a 65% minimum free area.

• Any vertical deflectors in the existing rear grille should

be removed to decrease condenser air recirculation

that can cause the unit to “short-cycle” and lead

to premature component failure.

Use the correct power cord

Local codes may require the use of arc fault or

leakage current detection devices on 230/208 volt

installations.

Check the “Essential

Elements” label for

important information.

Replacing a ducted unit

New ducted installation:

If this unit is to be installed in a new ducted application

using a duct adapter kit, the kit must be installed before

the unit is placed in the wall case. The installation

instructions are packed with the kit.

Existing ducted installation:

Replacement of an existing ducted unit may require

different components. Request this information from

your sales representative.

• Replacing 230/208 volt units:

See page 14.

• Replacing 265 volt units:

See pages 15 and 16.

Mounting

plate

Duct

Case

REPLACING AN EXISTING UNIT?

Installation Instructions

HOW TO CONNECT

IF USING AN ELECTRICAL

SUBBASE

1 Remove the room cabinet.

2 Connect to electrical power.

3 See the special instructions below for applicable

supply voltages.

4 Reinstall the room cabinet.

Tandem

15 Amp.

230/208 volt receptacle configuration.

Perpendicular

20 Amp.

Large Tandem

30 Amp.

Order Kit RAK4002A for 230/208 volt direct

connection.

Power cords may include an arc fault interruption or

a leakage current detection interruption device. A

test and reset button is provided on the plug case or

the inline case. The device should be tested on a

periodic basis by first pressing the TEST button and

then the RESET button. If the TEST button does

not trip or if the RESET button will not stay engaged,

discontinue use of the Zoneline and contact a

qualified service technician.

230/208 volt models may be installed using one of

the following electrical subbases:

*Not approved for use on 7000 BTU models.

Electrical subbases provide an enclosure for direct

connection or enclosed receptacles. The subbase kit

includes the power cord.

The instructions provided with the selected subbase kit

must be carefully followed. It is the responsibility of the

installer to ensure the connection of components is

done in accordance with these instructions and all

electrical codes.

Branch Circuit and Proper GE

Unit Amperage Rating Subbase Kit

15 RAK204D15P

20 RAK204D20P

30 RAK204D30P*

A power supply kit must be used to supply power to the

Zoneline unit. The appropriate kit is determined by the

voltage, the means of electrical connection and the

amperage of the branch circuit.

Connections of 208 or 230 volt circuits may be with a

power supply kit or a junction box kit.

All wiring, including installation of the receptacle,

must be in accordance with the NEC and local codes,

ordinances and regulations. Local codes may require

the use of an arc fault or leakage current detection

device on the power cord. Be sure to select the

correct cord for your installation.

Power supply kit

Branch Circuit and Proper GE Power Cord

Unit Amperage Rating with LCDI Device

15 RAK3153

20 RAK3203

30 RAK3303*

14

230/208 VOLT ELECTRICAL SUPPLY

*Not approved for use on 7000 BTU models.

REMOVE JUNCTION BOX

1 Remove the junction box cover by removing the

front two screws.

2 Remove the junction box by removing the top and

bottom rear screws. Note how the tabs on the lower

left side of the junction box serve to hold the side in

place. This will help when the box is being reinstalled.

1

Unit connector

Junction

box cover

Junction

box

15

Installation Instructions

265 VOLT ELECTRICAL SUPPLY

WARNING:

Connection of this 265 V AC product to a branch circuit

MUST be done by direct connection in accordance with

the National Electrical Code. Plugging this unit into a

building mounted exposed receptacle is not permitted

by code.

These models must be installed using the appropriate

GE power supply kit for the branch circuit amperage

and the electrical resistance heater wattage desired.

Use the POWER CONNECTION CHART on page 17

to determine the correct kit required. One of the

following installation methods (A or B) must be used.

CUT AND STRIP THE CORDSET

1 Remove the cordset from the power supply kit.

Measure 6″ down the cord from where it emerges

from the back of the nylon plastic connector

and cut the cord through at this point.

2 Carefully remove 3″ of the cordset insulation

so as to expose the three insulated wires.

3 Strip 3/4″ of the insulation away at the end

of each of the three wires (L1, Neutral and

Ground). Plug the connector fully into place

in the unit mating connector. Be sure the

locking tabs at the sides are engaged.

2

3/4″

3″

Connector

6″

NOTE: Order Kit RAK4002CW to enable a quick

disconnect inside the junction box.

A. FOR SUBBASE INSTALLATION

Electrical subbase kits are available to provide a flexible

enclosure for direct connection.

The instructions provided with the selected subbase kit must

be carefully followed. It is the responsibility of the installer

to ensure the connection of components is done in

accordance with these instructions and all electrical codes.

Branch Circuit and Proper GE Power

Unit Amperage Rating Subbase Kit Supply Kit

15 RAK204E15 RAK5172

20 RAK204E20 RAK5202

30 RAK204E30 RAK5302

B. FOR DIRECT CONNECT

INSTALLATION

If an electrical subbase is not used, direct connection to

branch circuit wiring inside the provided junction box must

be done in accordance with the following steps.

HOW TO CONNECT

1 Remove the room cabinet.

2 Connect to electrical power.

3 See the special instructions below for applicable

supply voltages.

4 Reinstall the room cabinet.

Installation Instructions

16

265 VOLT ELECTRICAL SUPPLY

REINSTALL JUNCTION BOX

• Reinstall the junction box by engaging the left tabs

on the lower right face of the unit, aligning the

screw holes at the top and bottom and driving the

two screws until secure. Be sure that all wire leads

are inside the box and not pinched between the box

and the unit. The green insulated ground wire from

the unit MUST be connected to the branch circuit

ground wire.

Make all wire connections by using appropriate

UL-listed electrical connectors and techniques

(black to black, white to white and green to green).

4

REINSTALL JUNCTION

BOX COVER

1 Carefully tuck all wires and connections back inside

the junction box. Be sure there are no loose

connections or stray uninsulated wires exposed.

2 Place the junction box cover in place. Replace the

two screws removed earlier and tighten securely.

3 Discard the unused portion of the plug and

the cordset.

5

ATTACH CONDUIT

1 Use the round knockout at the bottom of the

junction box to attach conduit coming from the

branch circuit. Remove the knockout, attach the

conduit and bring wires into the junction box.

Leave 6″ of wire free at the end of the conduit

to allow connections to be made.

2 If a fuse and fuseholder are to be used, the

knockout at the top of the box is for mounting

a Buss Fuseholder. Be sure the fuse and fuseholder

are of the same rating as the branch circuit.

Leadwires at the fuse can be either soldered in

place or attached using UL-listed 1/4″ female

(receptacle) crimp connectors.

3

Conduit

230/208 Volt

Power Supply Kits

with Leakage

Current Detection Wall Plug Heater Wattage

Device Configuration Circuit Protective Device @ 230/208 Volts

RAK3153* Tandem 15 Amp Time Delay Fuse or Breaker 2.55/2.09 KW

RAK3203* Perpendicular 20 Amp Time Delay Fuse or Breaker 3.45/2.82 KW

RAK3303* Large Tandem 30 Amp Time Delay Fuse or Breaker 5.00/4.10 KW

265 Volt

Power Wall Plug Heater Wattage

Supply Kits Configuration Circuit Protective Device @ 265 Volts

RAK5172* Does Not Apply 15 Amp Time Delay Fuse or Breaker 2.55 KW

RAK5202* Does Not Apply 20 Amp Time Delay Fuse or Breaker 3.45 KW

RAK5302* Does Not Apply 30 Amp Time Delay Fuse or Breaker 5.0 KW

*Not approved for use on 7000 BTU models.

Installation Instructions

17

POWER CONNECTION CHART

Installation Instructions

18

INSTALL THE WALL CASE AND

EXTERIOR GRILLE

The RAB71 series or RAB77 wall case must be

properly installed per instructions packed with

the case.

• Remove the corrugated stiffener and the outdoor

protective panel. Use the slit in the outdoor panel

as a handhold and push out.

• Install the exterior grille from the room side

following instructions packed with the grille.

Insulated Wall Case

This unit is designed to be installed in a GE plastic

or an insulated steel wall case. This minimizes

condensation from forming on the room side of

the case.

The RAB71 series wall cases are insulated. Insulation

kit RAK901L is available for use with RAB77 or

existing uninsulated wall cases when needed.

NOTE: For installation with a subbase or duct adapter,

see the instructions packed with those kits.

1

Stiffener

Protective

panel

Slit

PREPARE THE UNIT

• Carefully remove shipping tape and foam shipping

blocks from the room cabinet, compressor and

vent door. There may be multiple blocks and pieces

of shipping tape that need to be removed.

• Remove the room cabinet by pulling it out at the

bottom to release it (1), then lift it up to clear the

rail along the unit top (2).

• If vent door is to be operational, remove shipping

screws from the front side of the vent door, if present.

2

Shipping tape

(Locations may vary)

Remove two

shipping screws

INSTALLING THE ZONELINE

INSTALL THE UNIT INTO THE

WALL CASE

Slide the unit into the wall case and secure with four

screws through the unit flange holes.

3

REPLACE THE ROOM CABINET

Reinstall the room cabinet by hooking the top over

the rail along the unit top (1), then pushing it in at

the bottom (2).

4

Installation Instructions

19

NOTE: There are several extra holes in the unit side

flanges for installation in wall cases other than GE.

To avoid damaging the flange insulation, the installer

should use an awl or other sharp tool to puncture the

insulation in the appropriate holes before installing

the attachment screws.

Installation Instructions

20

OPTIONAL—DRAIN KIT INSTALLATION

Dry Air 25 Series models are designed to improve dehumidification by 25%. Since more moisture will be removed from

the air, there is a greater possibility that water will drip from the wall case than with a standard unit. To prevent this water

from dripping onto external building walls, we recommend the use of RAD10 Drain Kit.

External Drain

See the Installation Instructions

in the RAD10 kit.

Internal Drain

See the Installation Instructions

in the RAD10 kit.

Type “A” screw for metal case or

Type “B” screw for molded case

Square drain holes

Neoprene sponge gasket

Steel mounting plate

1/2″ O.D. drain tube

Neoprene sponge gasket

Steel mounting plate

Type “A” screw for metal case or

Type “B” screw for molded case

Alternate:

6″ long, 1/2″ O.D. straight

copper tube

La page charge ...

GE 3800 Manuel utilisateur

Ce manuel convient également à

GE 3800 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents