Hotpoint HQ9I MO1L UK Mode d'emploi

In or

der to receive a more complete assistance, please

register your product on www.hotpoint.eu.

W11456755A

810F950001492

2

REFRIGERATOR USER INSTRUCTIONS ........................................... 3

INSTRUCTIONS D’UTILISATION DU RÉFRIGÉRA

TEUR

.............. 43

..............

Français

English

3

FRENCH DOOR BOTTOM MOUNT REFRIGERA

TOR

USE AND CARE GUIDE

T

able of Contents

REFRIGERA

TOR SAFETY

.............................................................. 4

Pr

oper Disposal of Your Old Refrigerator

........................................8

P

ARTS AND FEATURES

................................................................9

WHA

T’S NEW BEHIND THE DOORS?

........................................10

INST

ALLATION INSTRUCTIONS .................................................11

Getting Started

...............................................................................11

W

ater Filter Installation

..................................................................11

Unpack the Refrigerator

................................................................11

Location Requir

ements

..................................................................12

Electrical Requir

ements

.................................................................12

Remove and Replace Refrigerator Doors

.....................................14

Remove and Replace Fr

eezer/Flexi Freeze Door

..........................16

Refrigerator Levelling

.....................................................................17

W

ater Supply Requirements

..........................................................17

Connect the W

ater Supply

.............................................................17

FIL

TERS AND ACCESSORIES

...................................................19

W

ater Filtration System

..................................................................19

Accessories

....................................................................................20

Assistance or Service

....................................................................20

USING THE CONTROLS

..............................................................21

Lighting the Refrigerator

................................................................23

REFRIGERA

TOR CONNECTIVITY FEATURES

.........................23

CONNECTIVITY SETUP

...............................................................24

Automatic Set-Up Instructions

—Wi-Fi Pr

otected Setup (WPS)

.....................................................24

W

ater and Ice Dispensers

..............................................................25

REFRIGERA

TOR USE

..................................................................27

Opening and Closing Doors

..........................................................27

Ice Maker and Storage Bin

...........................................................28

SHEL

VES, BINS, AND DRAWERS

...............................................29

Fr

eezer Storage Compartments

....................................................30

Cleaning

.........................................................................................31

Lights

..............................................................................................31

Holiday and Moving Car

e

..............................................................31

TROUBLESHOOTING - CONNECTED MODELS

......................33

TROUBLESHOOTING

..................................................................35

PERFORMANCE DA

TA SHEET

...................................................41

4

REFRIGERATOR SAFETY

You can be killed or seriously injured if you don't immediately

You

can be killed or seriously injured if you don't

follow

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”

These words mean:

follow instructions.

instructions.

DANGER

WARNING

5

SAFETY INSTRUCTIONS

IMPORTANT TO BE READ AND OBSERVED

Before using the appliance, read these safety

instructions. Keep them nearby for future

reference. These instructions and the appliance

itself provide important safety warnings, to be

observed at all times. The manufacturer declines

any liability for failure to observe these safety

instructions, for inappropriate use of the appliance

or incorrect setting of controls.

Very young children (0-3 years) should be kept

away from the appliance. Young children (3-8

years) should be kept away from the appliance

unless continuously supervised. Children from 8

years old and above and persons with reduced

physical, sensory or mental capabilities or lack of

experience and knowledge can use this appliance

only if they are supervised or have been given

instructions on safe use and understand the

hazards involved. Children must not play with the

appliance. Cleaning and user maintenance must

not be carried out by children without supervision

.

Children aged from 3 to 8 years are allowed to load

and unload refrigerating appliances.

PERMITTED USE

CAUTION: The appliance is not intended to

be operated by means of an external switching

device, such as a timer, or separate remote

controlled system.

This appliance is intended to be used in

household and similar applications such as: sta

kitchen areas in shops, oces and other working

environments; farm houses; by clients in hotels,

motels, bed & breakfast and other residential

environments.

This appliance is not for professional use. Do

not use the appliance outdoors.

The bulb used inside the appliance is specically

designed for domestic appliances and is not

suitable for general room lighting within the

home (EC Regulation 244/2009).

The appliance is designed for operation in

places where the ambient temperature comes

within the following ranges, according to the

climatic class given on the rating plate. The

appliance may not work properly if it is left for a

long time at a temperature outside the specied

range.

Climatic Class Amb. T. (°C)

SN: From 10 to 32 °C; N: From 16 to 32 °C

ST: From 16 to 38 °C; T: From 16 to 43 °C

This appliance does not contain CFCs. The

refrigerant circuit contains R600a (HC). Appliances

with Isobutane (R600a): isobutane is a natural gas

without environmental impact, but is ammable.

Therefore, make sure the refrigerant circuit pipes

are not damaged, especially when emptying the

refrigerant circuit.

WARNING: Do not damage the appliance

refrigerant circuit pipes.

WARNING: Keep ventilation openings, in the

appliance enclosure or in the built-in structure,

clear of obstruction

.

WARNING: Do not use mechanical, electric or

chemical means other than those recommended

by the Manufacturer to speed up the defrost

process.

WARNING: Do not use or place electrical

devices inside the appliance compartments if

they are not of the type expressly authorised by

the Manufacturer.

WARNING: Ice makers and/or water dispensers

not directly connected to the water supply must

be lled with potable water only.

WARNING: Automatic ice-makers and/or water

dispensers must be connected to a water supply

that delivers potable water only, with mains water

pressure between 20 psi and 145psi (1.4 bar and

10bar).

Do not store explosive substances such as

aerosol cans with a ammable propellant in this

appliance.

Do not swallow the contents (non-toxic) of

the ice packs (provided with some models). Do

not eat ice cubes or ice lollies immediately after

taking them out of the freezer since they may

cause cold burns.

For products designed to use an air lter inside

an accessible fan cover, the lter must always be

in position when the refrigerator is in function.

Do not store glass containers with liquids in

the freezer compartment since they may break.

Do not obstruct the fan (if included) with food

items. After placing the food check that the door

of the compartments closes properly, especially

the freezer door.

Damaged gaskets must be replaced as soon as

possible.

Use the refrigerator compartment only for

storing fresh food and the freezer compartment

only for storing frozen food, freezing fresh food

and making ice cubes.

Avoid storing unwrapped food in

direct contact with internal surfaces of

the fresh food or freezer compartments.

Appliances could have special compartments

(Fresh Food Compartment, Zero Degree Box, etc.).

Unless specied in the specic booklet of product,

they can be removed, maintaining equivalent

performances.

Warning: Risk of re/ammable materials

The most appropriate compartments of the

appliance where specic types of food are to be

stored, taking into account dierent temperature

distribution in dierent compartments in the

appliance, are as follows:

- Refrigerator compartment: Store tropical fruit,

6

cans

, drinks, eggs, sauces, pickles, butter, jam,

cheese, milk, dairy food, yoghurt. You may also

store cold cuts, desserts, meat and sh,

cheesecake, fresh pasta, sour cream, pudding and

cream cheese.

Fruit & vegetable drawer at the bottom of the

refrigerator compartment: Store vegetables and

fruits (excluding tropical fruits).

Chiller compartment: Only store meat and sh in

the coldest drawer

- Freezer compartment:

is suitable for freezing foodstus from ambient

temperature and for storing frozen food as the

temperature is evenly distributed throughout

the entire compartment. Purchased frozen food

has the storage expiration date stated on the

packaging. This date takes into account the type of

food being stored and therefore this date should

be respected. Fresh food should be stored for the

following time periods: 1-3 months for cheese,

shellsh, ice cream, ham/sausage, milk, fresh

liquids; 4 months for steak or chops (beef, lamb,

pork); 6 months for butter or margarine, poultry

(chicken, turkey); 8-12 months for fruits (except

citrus), roast meat (beef, pork, lamb), vegetables.

Expiration dates on the packaging of foods must

be respected. To avoid food contamination, please

observe the following:

– Opening the door for long periods can cause

a signicant increase of the temperature in the

compartments of the appliance.

– Regularly clean surfaces that may come into

contact with food and accessible drainage

systems.

– Clean water tanks if they have not been used for

48 h; ush the water system connected to a water

supply if water has not been drawn for 5 days.

– Store raw meat and sh in suitable containers

in the refrigerator, so that it does not come into

contact with or drip onto other food.

In the Convertible Zone

storage should be as followed:

+10°C : store white wine

+4°C: store vegetables and fruits (excluding

tropical fruits)

0°C: only store meat and sh

All set points below zero: store frozen foodstu as

for freezer cavity

– Two-star frozen food compartments are suitable

for storing pre-frozen food, storing or making ice

cream and ice cubes.

– Do not freeze fresh food in one, two or three-

star compartments.

– If the refrigerating appliance is left empty for

long periods, switch o, defrost, clean, dry, and

leave the door open to prevent mould developing

inside the appliance.

INSTALLATION

The appliance must be handled and installed by

two or more persons- risk of injury. Use protective

gloves to unpack and install- risk of cuts.

I

nstallation, including water supply (if any)

and electrical connections, and repairs must

be carried out by a qualied technician. Do not

repair or replace any part of the appliance unless

specically stated in the user manual. Keep

children away from the installation site.

After unpacking the appliance, make sure that

it has not been damaged during transport. In

the event of problems, contact the dealer or

your nearest After-sales Service. Once installed,

packaging waste (plastic, styrofoam parts etc.)

must be stored out of reach of children - risk of

suocation. The appliance must be disconnected

from the power supply before any installation

operation - risk of electric shock. During

installation, make sure the appliance does not

damage the power cable - risk of re or electric

shock. Only activate the appliance when the

installation has been completed.

Be careful not to damage the oors (e.g.

parquet) when moving the appliance. Install the

appliance on a oor or support strong enough

to take its weight and in a place suitable for its

size and use. Make sure the appliance is not near

a heat source and that the four feet are stable and

resting on the oor, adjusting them as required,

and check that the appliance is perfectly level

using a spirit level. Wait at least two hours before

switching the appliance on, to ensure that the

refrigerant circuit is fully ecient.

WARNING: When positioning the appliance,

ensure the supply cord is not trapped or damaged.

WARNING: To avoid a hazard due to instability,

positioning or xing of the appliance must be done

in accordance with the manufacturer instructions.

It is forbidden to place the refrigerator in such

way that the metal hose of gas stove, metal gas or

water pipes, or electrical wires are in contact with

the refrigerator back wall (condenser coil).

To guarantee adequate ventilation, leave a

space on both sides and above the appliance. The

distance between the rear of the appliance and

the wall behind the appliance should be 50mm,

to avoid access to hot surfaces. A reduction of this

space will increase the Energy consumption of

product.

I

f it is necessary to replace the doors, please

contact the Technical Assistance Center.

A

n 'Approved' single check valve or some other

no less eective backow prevention device

providing backow prevention protection to at

least uid category two shall be tted at the point

of connection(s) between the water supply and

the fitting or appliance.

7

ELECTRICAL WARNINGS

I

t must be possible to disconnect the appliance

from the power supply by unplugging it if plug

is accessible, or by a multi-pole switch installed

upstream of the socket in accordance with the

wiring rules and the appliance must be earthed

in conformity with national electrical safety

standards.

D

o not use extension leads, multiple sockets

or adapters. The electrical components must not

be accessible to the user after installation. Do not

use the appliance when you are wet or barefoot.

Do not operate this appliance if it has a damaged

power cable or plug, if it is not working properly,

or if it has been damaged or dropped.

I

f the supply cord is damaged, it must be replaced

with an identical one by the manufacturer, its

service agent or similarly qualied persons in

order to avoid a hazard- risk of electric shock.

WARNING: Do not locate multiple portable

socket-outlets or portable power supplies at the

rear of the appliance

.

CLEANING AND M

AINTENANCE

WARNING: Ensure that the appliance is

switched o and disconnected from the power

supply before performing any maintenance

operation; never use steam cleaning equipment-

risk of electric shock.

D

o not use abrasive or harsh cleaners such as

window sprays, scouring cleansers, ammable

uids, cleaning waxes, concentrated detergents,

bleaches or cleansers containing petroleum

products on plastic parts, interior and door liners

or gaskets. Do not use paper towels, scouring

pads, or other harsh cleaning tools.

DISPOSAL OF P

ACKAGING MATERIALS

T

he pack

aging material is 100% recyclable and is marked with the

recycle symbol

.

T

he various parts of the packaging must therefore be disposed of

responsibly and in full compliance with local authority regulations

governing waste disposal.

DISPOSAL OF HOUSEHOLD APPLIANCES

T

his appliance is manufactured with recyclable or reusable materials.

Dispose of it in accordance with local waste disposal regulations.

For further information on the treatment, recovery and recycling of

household electrical appliances, contact your local authority, the

collection service for household waste or the store where you purchased

the appliance. This appliance is marked in compliance with European

Directive 2012/19/EU, Waste Electrical and Electronic Equipment

(WEEE). By ensuring this product is disposed of correctly, you will help

prevent negative consequences for the environment and human health.

The symbol

on the pr

oduct or on the accompanying documentation

indicates that it should not be treated as domestic waste but must be

taken to an appropriate collection center for the recycling of electrical

and electronic equipment.

ENER

GY SAVING TIPS

I

nstall the appliance in a dry, well ventilated room far away from any

heat source (eg. radiator, cooker, etc.) and in a place not exposed directly

to the sun. If required, use an insulating plate.

To guarantee adequate ventilation follow installation instructions.

Insucient ventilation at the back of the product increases energy

consumption and decreases cooling eciency.

Frequent door opening might cause an increase in Energy Consumption.

The internal temperature of the appliance and the Energy Consumption

may be aected also by the ambient temperature, as well as location

of the appliance. Temperature setting should take into consideration

these factors.

Reduce door opening to a minimum.

When thawing frozen food, place in the refrigerator. The low temperature

of the frozen products cools the food in the refrigerator. Allow warm

food and drinks to cool down before placing in the appliance.

Positioning of the shelves in the refrigerator has no impact on the

ecient usage of energy. Food should be placed on the shelves in such

way to ensure proper air circulation (food should not touch each other

and distanc

e between food and rear wall should be kept).

You can increase storage capacity of frozen food by removing baskets

and

, if present, Stop Frost shelf.

Do not worry about noises coming from the compressor which are

described as normal noises in this product's Quick Guide.

in accordance to AS/NZS 3500.1.2 and complying

with AS/NZS 2845.1.

FOR AUSTRAL IA ONL Y: A backflow device Water-

Mark approved (not included, responsibility of the

plumbing) is required to be installed upstream in

accordance with the WaterMark cer tification and

8

Proper Disposal of Your Old

Refrigerator

DANGER : Risk of child entrapment. Before you throw away

your old refrigerator or freezer:

■ Take off the doors.

■ Leave the shelves in place so that children cannot easily climb

inside.

IMPORTANT: Child entrapment and suffocation are not problems

of the past. Scrapped or abandoned refrigerators are still

dangerous—even if they will sit for “just a few days.” If you are

getting rid of your old refrigerator, please follow these instructions

to help avoid accidents.

WARNING

Suffocation Hazard

Remove doors from your old refrigerator.

Failure to do so can result in death or

brain damage.

Important information to know about disposal of

refrigerants:

Dispose of refrigerator in accordance with Federal and Local

regulations. Refrigerants must be evacuated by a licensed,

EPA certified refrigerant technician in accordance with

established procedures.

9

PARTS AND FEATURES

Storage Capacity:

Please check the rating label in the back of the product.

In-door Ice Maker

and Ice Bucket

Activ e Oxygen

Pull Out Platter

Fresh Box

Water Filter Delicates Pantry Drawer

Adjustable Shelf

Fr

esh Box

Adjustable Shelf

2 top Light Strips

2 side Light Strips

Easy Access T

ray

Fast Freeze Drawers

A. Refrigerator

B. Fr

eezer

C. Flexi Freeze

A

B C

User Interface

Ice and W

ater

Dispense Paddles

Pull out

Dripping T

ray

10

WHA

T’S NEW BEHIND THE DOORS?

In-Door

-Ice

®

Storage Bin

The ice maker and ice storage bin ar

e located in the door for easy

access to ltered ice while freeing up valuable shelf space inside

and adding additional door bins for more usable space.

Freeze Shield

This feature minimizes moisture migration in the frozen food and

reduces the freezer burn occurrence.

Pull out Platter

This full-width side-out shelf tucked between the crispers and the

lowest shelf is perfect for leftover family-sized casserole dishes,

pizza boxes, and large party platters.

Delicates Pantry Drawers

To store things like meat, deli items, and drinks to keep in their

ideal cooling environment.

Water Dispenser with Measured Fill

The Measured Fill feature allows you to dispense a desired

amount of ltered water in handy increments like 0.2 liter, 0.5 liter

and 1.0 liter.

Panoramic LED lighting

Multiple strips of LED lights inside the refrigerator compartment,

freezer compartment, and interior drawers minimize shadows and

evenly distribute light throughout the refrigerator.

Convertible Zone

Switch from freezer to fridge in one touch by selecting among the

6+ preset temperatures and create the space you want according

to your evolving needs.

Active Oxygen

Hygiene, with innovative device releasing ozone to reduce odours

and prevent the proliferation of bacteria inside the cabinet,

improving the air quality for a better environment.

11

INSTALLATION INSTRUCTIONS

Getting Started

INST

ALLATION CHECKLIST

Electrical Power

■ Plug refrigerator into a earthed socket.

Doors

■

If doors need to be r

emoved during installation, see the

“Remove and Replace Refrigerator Doors” and “Remove and

Replace Freezer Door Fronts” sections.

■

Doors seal completely

.

■

Refrigerator is level. Adjust leveling feet so they ar

e snug

against the oor.

■

Doors ar

e even across the top. (Use door alignment feature if

necessary).

Final Checks

■

Remove all shipping material.

■

Set temperatur

e controls to the recommended setting.

■

Save instructions and other literatur

e.

■

In or

der to receive a more complete assistance, please

register your product on www.hotpoint.eu.

W

ater Filter Installation

n

Locate the water lter compartment in the lower left-hand side

of the r

efrigerator compartment. Push on the right side of the

lter door to open.

n Align the arr

ow on the water lter cap with the cutout notch in

the lter housing and insert lter.

n

Once the lter is inserted, tur

n the lter clockwise 90° (1/4

turn) until it locks into the housing.

n

Push water lter door closed to latch.

n

Flush 3 gallons (11.4 L) of water thr

ough the water system to

clear air from the water line and to keep the dispenser from

dripping and/or avoiding decreased dispenser ow.

n

Reset the lter counter via user interface. See the pr

ocedure

to reset the lter in the User Controls section.

NOTE: If the lter is not installed corr

ectly, water may dispense at

a lower ow rate and there will be slower ice production. Improper

lter installation may also cause the water lter housing to leak.

Unpack the Refrigerator

Refrigerator Delivery

A minimum door opening of 838 mm (33") is r

equired. If door

opening is 914 mm (36") or less, then removal of doors, drawer

and hinges is required.

Cart the refrigerator from the side for all door openings.

Remove the Packaging

■

Remove tape and glue r

esidues from surfaces before

turning on the refrigerator. Rub a small amount of liquid dish

detergent over the adhesive with your ngers. Wipe with warm

water and dry.

■

Do not use sharp instruments, rubbing alcohol, ammable

uids, or abrasive cleaners to r

emove tape or glue. These

products can damage the surface of your refrigerator.

■

Dispose of/r

ecycle all packaging materials.

Clean Before Using

After you remove all of the packaging materials, clean inside of

your refrigerator before using it. See cleaning instructions in the

“Refrigerator Care” section.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

WARNING

Excessive Weight Hazard

Use two or more people to move and install

refrigerator.

Failure to do so can result in back or other injury.

When Moving Your Refrigerator:

Your refrigerator is heavy. When moving the refrigerator for

cleaning or service, be sure to cover the oor with

cardboard or hardboard to avoid oor damage. Always pull

the refrigerator straight out when moving it. Do not wiggle or

“walk” the refrigerator when trying to move it, as oor

damage could occur.

Important information to know about glass shelves

and covers:

Do not clean glass shelves or covers with warm water when

they are cold. Shelves and covers may break if exposed to

sudden temperature changes or impact, such as bumping.

Tempered glass is designed to shatter into many small,

pebble-size pieces. This is normal. Glass shelves and covers

are heavy. Use both hands when removing them to avoid

dropping.

12

Location Requir

ements

T

o ensure proper ventilation for your refrigerator, allow for a

1.25 cm space on each side and at the top. Allow for a 5 cm

space behind the refrigerator. If your refrigerator has an ice maker,

allow extra space at the back for the water line connections.

When installing your refrigerator next to a xed wall, leave a 9.5

cm minimum space between the refrigerator and wall to allow the

door to swing open.

NOTE: This refrigerator is intended for use in a location where

the temperature ranges from a minimum of 10°C to a maximum

of 43°C. The preferred room temperature range for optimum

performance, which reduces electricity usage and provides

superior cooling, is between 15°C and 32°C. It is recommended

that you do not install the refrigerator near a heat source, such as

an oven or radiator.

Electrical Requir

ements

IMPOR

TANT: Installation and electrical connection must

be carried out by a qualied technician according to the

manufacturer’s instructions and in compliance with the local

safety regulations.

■

The r

efrigerator is designed to operate on a separate

220-240 V, 10 A, 50-60 Hz circuit.

■

Make sur

e the voltage specied on the rating plate

corresponds to that of your home.

■

It must be possible to disconnect the appliance fr

om the

power supply by unplugging it or by means of a main two pole

switch installed upstream of the socket.

■

If the supply cor

d is damaged, it must be replaced by the

manufacturer, its service agent or similarly qualied persons in

order to avoid a hazard.

Before you move your refrigerator into its nal location, it is

important to make sure you have the proper electrical connection:

Recommended Earthing Method

220-240 V 50 Hz, 220 V 60 Hz, or 230/240 V 50 Hz AC only 10 A

fused and earthed electrical supply is required.

For Australia and New Zealand:

Your new appliance has been especially manufactured to meet all

Australian Standards and Conditions.

Some notations in the installation instructions may refer to

electrical requirements in other countries, so we draw your

particular attention to these specic notes.

Your appliance needs to be plugged into a 230/240 V 50 Hz AC

only 10 A earthed socket.

WARNING

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from refrigerator.

Failure to do so can result in death, explosion, or fire.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

WARNING

Type B

Type E and F

Type I

Type M

Type G

T

ype N

1.25 cm

9.5 cm

13

Electrical Requirements (Great Britain and Ireland only)

IMPORTANT: This refrigerator must be earthed.

Fuse Replacement

If the main lead of this refrigerator is tted with a BS1363A,

13 A fused plug, to replace a fuse in this type plug use an A.S.T.A.

approved fuse to BS 1362 type and proceed as follows:

1. Remove the fuse cover (A) and fuse (B).

2. Fit replacement 13 A fuse into the fuse cover.

3. Reinsert both the fuse and its cover into the plug.

IMPORTANT: The fuse cover must be retted when changing a

fuse. If fuse cover is lost, the plug must not be used until a correct

replacement cover is tted. A correct replacement is identied by

the colour insert or colour “word” embossed on the base of the

plug. Replacement fuse covers are available at your local

electrical shop.

For the Republic of Ireland (only):

The information given in respect of Great Britain will frequently

apply, but a third type of plug and socket is also used, the 2-pin,

side earth type.

Socket/Plug (valid for both countries):

If the tted plug is not suitable for your socket, please contact

After-sales Service for further instruction. Please do not

attempt to change the plug yourself. This procedure needs

to be carried out by a qualied technician in compliance with

the manufacturer’s instructions and current standard safety

regulations.

Temperature

This refrigerator is designed for operation in places where the

temperature comes within the following ranges, according to

climatic class shown on the rating plate. The refrigerator may not

work properly if it is left for a long time at a temperature outside

the specied range.

NOTE: It is recommended that you do not install the refrigerator

near a heat source, such as an oven or radiator.

Climatic Class Amb. T. (°C) Amb. T. (°F)

SN From 10 to 32 From 50 to 90

N From 16 to 32 From 61 to 90

ST From 16 to 38 From 61 to 100

T From 16 to 43 From 61 to 110

A

A. Fuse cover

B. Fuse

B

14

Remove and Replace Refrigerator Doors

NOTE: Measur

e the width of your door opening to see whether or not you need to remove refrigerator doors to move refrigerator into

your home. If door removal is necessary, see the following instructions.

IMPORTANT: If refrigerator was previously installed and you are moving it out of the home, turn refrigerator control off before you begin

removing the doors. Unplug refrigerator or disconnect power. Remove food and adjustable door or utility bins from doors.

Gather required tools and read all instructions before removing doors.

TOOLS NEEDED: 6 mm socket wrench, 5 mm socket wrench and #2 Phillips screwdriver.

WARNING

Electrical Shock Hazard

Disconnect power before removing doors.

Failure to do so can result in death or electrical shock.

T

op Right Hinge Cover

A. T

op Hinge Cover screws

B. Top Hinge Cover

A

B

T

op Right Hinge

A. 5 mm socket scr

ews

A

A. Hinge

Middle Right Hinge

A

T

op Left Hinge Cover

A. T

op Hinge Cover screws

B. Top Hinge Cover

A

B

A

T

op Left Hinge

A. 5 mm socket scr

ews

Middle Left Hinge

A. Hinge

A

W

ater Dispenser

Tubing Connection

A. Outer ring

A

Wiring Plug

15

Remove Refrigerator Doors

Remove Right-Hand Door

1. Unplug refrigerator or disconnect power.

2. Keep refrigerator doors closed until you are ready to lift them

free from the cabinet.

NOTE: Provide additional support for refrigerator door while the

hinges are being removed. Do not depend on the door gasket

magnets to hold the door in place while you are working.

3. Using a Phillips screwdriver, remove cover from top hinge.

4. Using 5 mm socket wrench, remove four screws from top

hinge and set aside.

5. Lift refrigerator door from the middle hinge pin. The top hinge

will come away with the door.

Remove Left-Hand Door

IMPORTANT: The wiring for UI run through left-hand door hinge,

so they must be disconnected before removing the door.

1. Using a Phillips screwdriver, remove cover from top hinge.

2. Disconnect two wiring plugs located on top of the door hinge.

■ Grasp each side of wiring plugs. With your left thumb,

press down to release the catch and pull the sections of

the plugs apart.

3. Disconnect the water dispenser tubing located on top of the

door hinge. Firmly pull up on the clasp. Then, pull the tubing

out of the fitting.

NOTE: The water dispenser tubing remains attached to the

left-hand refrigerator door.

WARNING

Excessive Weight Hazard

Use two or more people to lift the refrigerator door.

Failure to do so can result in back or other injury.

WARNING

Electrical Shock Hazard

Disconnect power before removing doors.

Failure to do so can result in death or electrical shock.

A. Top hinge cover screw

B. Top hinge cover

C. 5 mm socket screws

D. Top hinge

A

B

D

A. Top hinge cover screw

B. Top hinge cover

A

B

A. Wiring Plug

B. Ground (earth) connector

A

B

C

16

4. Using 5 mm socket wrench, remove four internal screws from

top hinge and set aside.

NOTE: Provide additional support for refrigerator door while

hinges are being removed. Do not depend on the door gasket

magnets to hold the door in place while you are working.

5. Lift refrigerator door from bottom hinge pin. The top hinge will

come away with door.

NOTE: It may not be necessary to remove bottom hinges and

brake feet assemblies to move the refrigerator through a doorway.

■ Only if necessary, use 6 mm socket wrench and #2 Phillips

screwdriver to remove middle hinge.

Replace Right-Hand Refrigerator Door

1. Set right-hand door onto middle hinge pin.

2. Insert top hinge pin into open hole in top of refrigerator door.

3. Using four 5 mm socket screws, fasten hinge to cabinet. Do

not tighten screws completely.

Replace Left-Hand Refrigerator Door

1. Set left-hand door onto middle hinge pin.

2. Using four 5 mm socket screws, fasten hinge to cabinet. Do

not tighten screws completely.

3. Reconnect electrical wiring.

■ Push together two sections of wiring plug.

■ Reconnect earth wire to hinge screw.

Final Steps

1. Completely tighten eight 5 mm socket screws.

2. Replace top hinge covers.

Remove and Replace Freezer/Flexi

Freeze Door

1. Keep freezer doors closed until you are ready to lift them free

from cabinet.

NOTE: Provide additional support for freezer door while hinges

are being removed. Do not depend on door gasket magnets to

hold door in place while you are working.

■ Using a #2 Phillips screwdriver and 6 mm socket wrench to

remove middle hinge from cabinet.

■ Lift freezer door from the bottom hinge pin.

A. 5 mm socket screws

B. Top Hinge

A

B

A. Middle hinge

A

A. Bottom hinge

A

17

Final Steps

1. Plug into an grounded (earthed) socket.

2. Return all removable parts and food to the drawers.

Refrigerator Levelling

1. Move refrigerator to its nal location.

2. Using hand, rotate the brake feet. Turn them counterclockwise

until the rollers are off the oor and both brake feet are snug

against the oor. This keeps refrigerator from rolling forward

when opening the doors.

IMPORTANT: If you need to make further adjustments

involving brake feet, you must turn both brake feet same

amount to keep the refrigerator level.

3. Use a level to make sure refrigerator is level from side to side

and front to back.

Water Supply Requirements

A cold water supply with water pressure between 20 psi and

145 psi (138 kPa and 1000 kPa) is required to operate the water

dispenser and ice maker. If you have questions about your water

pressure, call a licensed, qualied plumber.

NOTE: If the water pressure is less than what is required, the ow

of water from the water dispenser could decrease or ice cubes

could be hollow or irregular shaped.

Reverse Osmosis Water Supply

IMPORTANT: The pressure of the water supply coming out

of a reverse osmosis system and supplying the water inlet valve

of the refrigerator needs to be between 20 psi and 145 psi

(138 kPa and 1000 kPa).

If a reverse osmosis water ltration system is connected to

your home cold water supply, the water pressure to the reverse

osmosis system needs to be a minimum of 40 to 60 psi (276 to

414 kPa).

■ Check to see whether the sediment lter in the reverse

osmosis system is blocked. Replace the lter if necessary.

■ Allow the storage tank on the reverse osmosis system to rell

after heavy use. The tank capacity could be too small to keep

up with the requirements of the refrigerator.

NOTE: Faucet-mounted reverse osmosis systems are not

recommended.

■ If your refrigerator has a water lter, it may further reduce

the water pressure when used in conjunction with a reverse

osmosis system. Remove the water lter. See the “Water

Filtration System” section.

If you have questions about your water pressure, call a licensed,

qualied plumber.

Connect the Water Supply

Read all directions before you begin.

IMPORTANT:

■ Connect to potable water supply only.

■ Plumbing must be installed in accordance with the

International Plumbing Code and any local codes and

ordinances.

■ Copper and PEX tubing connections from the household

water line to the refrigerator are acceptable and will help

avoid off-taste or odor in your ice or water. Check for leaks.

If PEX tubing is used instead of copper, we recommend the

following: 7 ft (2.14 m) jacketed PEX, 5 ft (1.52 m) PEX, or

25 ft (7.62 m) PEX.

■ Install tubing only in areas where temperatures will remain

above freezing.

Tools Needed:

Gather the required tools and parts before starting installation.

■ Flat-blade screwdriver

■ 7/16" and 1/2" open-end wrenches or 2 adjustable wrenches

■ 1/4" nut driver

NOTE: Do not use a piercing-type or 3/16" (4.76 mm) saddle

valve, which reduces water ow and clogs easier.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

WARNING

A

A. Brake feet

Do not use with water that is microbiologically unsafe or

of unknown quality without adequate disinfection before

or after the system. Systems certified for cyst reduction

may be used on disinfected waters that may contain

filterable cysts.

18

Connect to Water Line

IMPORTANT: If you have turned the refrigerator on before the

water was connected, turn off the ice maker.

1. Unplug refrigerator or disconnect power.

2. Turn off main water supply. Turn on nearest faucet long

enough to reduce water pressure in the water line.

3. Use a 3/4-14" shut-off valve or equivalent. The refrigerator is

provided with a household supply line with the installation kit

that connects to the shut-off valve and to the refrigerator.

NOTE: Appliance is equipped with a water installation kit. To

assure proper connection to your water supply, use proper sealing

material in the connection. Check if connection is sealed properly

after some hours of operation.

4. Now you are ready to connect the copper tubing to the

shut-off valve. Use 1/4" (6.35 mm) O.D. (outside diameter)

soft copper tubing to connect the shut-off valve and the

refrigerator.

■ Ensure that you have the proper length needed for the job.

Be sure both ends of the copper tubing are cut square.

■ Slip compression sleeve and compression nut onto copper

tubing as shown. Insert end of tubing into outlet end squarely

as far as it will go. Screw compression nut onto outlet end

with adjustable wrench. Do not overtighten.

A. Compression sleeve

B. Compression nut

C. Copper tubing

A

C

B

5. Place the free end of the tubing into a container or sink and

turn on main water supply to ush out tubing until water is

clear. Turn off shut-off valve on the water pipe.

NOTE: Always drain the water line before making the nal

connection to the inlet of the water valve to avoid possible

water valve malfunction.

6. Bend the copper tubing to meet the water line inlet, located

on the back of the refrigerator cabinet as shown. Leave a coil

of copper tubing to allow the refrigerator to be pulled out of

the cabinet or away from the wall for service.

Connect to Refrigerator

Follow the connection instructions specic to your model.

1. Remove plastic cap from water valve inlet port. Attach the

copper tubing to the valve inlet using a compression nut

and sleeve as shown. Tighten the compression nut. Do not

overtighten. Conrm copper tubing is secure by pulling on

copper tubing.

2. Create a service loop with the copper tubing. Avoid kinks

when coiling the copper tubing. Secure copper tubing to

refrigerator cabinet with a “P” clamp.

A. Copper tubing

B. “P” clamp

C. Compression nut

D. Compression sleeve

A

B

C

D

3. Turn on water supply to refrigerator and check for leaks.

Correct any leaks.

4. If ice is desired, turn on the ice maker.

Note: Allow 24 hours to produce the rst batch of ice. Discard

the rst three batches of ice produced. Allow three days to

completely ll the ice storage bin.

A. Sleeve

B. Nut

A

B

C

D

C. Copper tubing (to refrigerator)

D. Household supply line

19

FILTERS AND ACCESSORIES

Water Filtration System

Replace and Install the Water Filter

The water lter should be replaced every 6 months based on

a ow rate of 0.50 gpm-0.60 gpm (1.89 lpm-2.27 lpm) that lters

200 gallons (757 L) of water.

To order a replacement lter, contact us. See the “Accessories”

section in the Use and Care Guide for information on ordering.

1. Push the water lter door to open, located bottom left of

refrigerator compartment.

2. Twist the water lter and turn 90° counterclockwise to unlock.

3. Pull the lter out of the housing.

Remove the water lter cap from the water lter being replaced.

4. Install the water lter cap onto the new lter. Be sure to align

the arrows so the groves in lter align with ribs in lter cap.

5. Insert the lter into the housing.

6. Twist the water lter and turn 90° clockwise until it locks into

place and the arrows are aligned.

7. Push the water lter door closed.

8. Reset the lter counter via user interface. See the procedure

to reset the lter in the User Control section.

Do not use with water that is microbiologically unsafe or

of unknown quality without adequate disinfection before

or after the system. Systems certified for cyst reduction

may be used on disinfected waters that may contain

filterable cysts.

20

The W

ater Filter Status Lights

The Water Filter status lights will help you know when to change

your water lter.

n

ORDER FIL

TER (yellow) - It is almost time to change the

water lter. “Order Filter” display is ON all of the time but

OFF in Showroom mode.

n REPLACE FIL

TER (red) - Replace the water lter. While you

are dispensing water, “Replace Filter” will blink 7 times and

an alert tone will sound 3 times.

NOTE: “REPLACE FILTER” will remain illuminated if the lter

is not reset on the user interface (UI).

n

RESET FIL

TER - Touch "Filter Reset" button for 3 seconds to

reset water lter. The display will do a 3-second countdown,

then ash the icon and play a tone.

Replace and Install the Active Oxygen

It is recommended to replace the Active Oxygen every 3 years as

the ozone generate degrades over time, reducing its impact on

food preservation. At the beginning of life, it generates an average

of 0.06 ppm.

To order and replace the Active Oxygen, please contact us. See the

“Accessories” section for information on ordering.

Accessories

T

o order accessories, contact the dealer from whom you

purchased your refrigerator.

Assistance or Service

Befor

e calling for assistance or service, please check the

"Troubleshooting" section. It may save you the cost of a service

call. If you still need help, follow the instructions below.

If you need replacement parts

To locate factory-specied replacement parts in your area,

contact the dealer from whom you purchased your refrigerator.

Warranty

Contact the dealer from whom you purchased refrigerator for

warranty information.

Keep this book and your sales slip together for future

reference. You must provide proof of purchase or installation

date for in-warranty service.

Write down the following information about your appliance to help

you obtain assistance or service if you ever need it. You will need

to know your complete model number and serial number. You

can nd this information on the model and serial number label,

located on the inside wall of the fresh food compartment.

Dealer name

Serial number

Address

Phone number

Model number

Purchase date

Refer to www.hotpoint.eu to contact.

La page charge ...

Hotpoint HQ9I MO1L UK Mode d'emploi

Hotpoint HQ9I MO1L UK Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents