Husqvarna 124L Manuel utilisateur

Marque: Husqvarna

Modèle: 124L

Catégorie: Coupe-herbe

Taper: Manuel utilisateur

Ce manuel convient également à

124C

English---2

115374427 Rev. 6 5/15/12

CONTENTS

Contents

CONTENTS

Contents 2........................

Note the following before starting 2....

KEY TO SYMBOLS

Symbols 3.........................

SAFETY INSTRUCTIONS

Personal protective equipment 4......

Machine’s safety equipment 4........

Cutting equipment 5.................

Checking, maintaining and servicing

the machine’s safety equipment 5.....

General safety precautions 7.........

Starting 8.........................

Fuel safety 8.......................

Transporting and storage 8...........

General working instructions 8........

Basic safety rules 8.................

Basic working techniques 9..........

KNOW YOUR TRIMMER

Know your trimmer 11................

ASSEMBLY

Fitting the loop handle 12.............

Fitting the trimmer guard and

trimmer head 12.....................

FUEL HANDLING

Fuel 13............................

Fueling 13..........................

STARTING AND STOPPING

Check before starting 14..............

Starting and stopping 14..............

MAINTENANCE

Carburetor 15.......................

Muffler 16..........................

Spark plug 16.......................

Air filter 17..........................

Maintenance schedule 17.............

Trimmer head line loading instructions 18..

TECHNICAL DATA

Technical data 19....................

EMISSION CONTROL

WARRANTY STATEMENT 20.........

Note the following before start-

ing:

Husqvarna AB has a policy of continuous

product development and therefore reserves

the right to modify the design and appearance

of products without prior notice. Long--term

exposure to noise can result in permanent

hearing impairment. Always use approved

hearing protection. Maintenance, replacement,

or repair of the emission control devices and

system may be performed by any nonroad

engine repair establishment or individual.

The Emissions Compliance Period re

erred

to on the Emissions Compliance label indicates

the number of operating hours for which the

engine has been shown to meet Federal emis-

si ons requirements . Category C = 50 hours,

B= 125 hours, and A = 300 hours.

For reference, please fill out the following

information that will be needed for future

servicing of your trimmer:

Model Number:

Serial Number:

Purchase Date:

Purchased From:

WARNING: A clearing saw,

brushcutter or trimmer can be

dangerous if used incorrectly or

carelessly , and can cause serious

or fatal injury to the operator or

others. It is extremely important

that you read and understand the

contents of this operator’s manual.

WARNING: Under no circum-

stances may the design of the

machine be modified without the

permission of the manufacturer.

Always use genuine accessories.

Non--authorized modifications

and/or accessories can result

in serious personal injury or the

death of the operator or others.

Your warranty may not cover

damage or liability caused by the

use of non--authorized accesso-

ries or replacement parts.

For customer assistance, call:

1-800-487-5951

www.husqvarna.com

WARNING

The engine exhaust from this product contains

chemicals known to the State of California to c ause

cancer, b irth defects or oth er reproductive h arm.

English---3

115374427 Rev. 6 5/15/12

KEY TO SYMBOLS

Only intended for trimmer heads.

Use unleaded or quality leaded

gasoline and two--stroke oil

mixed at a ratio of 2% (1:50).

Other symbols/decals on the machine

refer to special certification requirements

for certain markets.

Stop the engine by pushing

and holding the stop switch

in the STOP position until the

engine stops before carrying

out any checks or maintenance.

Regular cleaning is required.

Visual check.

Approved eye protection must

always be used.

Symbols

WARNING: Clearing saws, brush-

cutters and trimmers can be dan-

gerous! Careless or incorrect use

can result in serious or fatal

injury to the operator or others.

WARNING: Read the operator’ s

manual before use. Failure to follow

instructions could result in serious

injury to the operator and/or

bystanders. Save operator’s manual.

Always wear:

S Hearing protection

S Approved eye protection

Watch out for thrown objects and

ricochets.

The operator of the machine

must ensure, while working,

that no persons or animals

come closer than 50 feet

(15 meters).

Arrows which show limits for

handle positioning.

Always wear approved protective

gloves.

Wear sturdy, non--slip boots.

Only use non--metallic, flexible

cutting attachments, i.e. trimmer

heads with trimmer line.

English---4

115374427 Rev. 6 5/15/12

SAFETY INSTRUCTIONS

GLOVES

Gloves should be worn when necessary,

e.g., when fitting cutting attachments.

HEARING PROTECTION

Wear hearing protection that provides

adequate noise reduction.

EYE PROTECTION

Always wear approved eye protection. If

you use a visor then you must also wear

approved protective goggles. Approved

protective goggles must comply with

standard ANSI Z87.1.

BOOTS

Wear sturdy, non--slip boots.

CLOTHING

Wear clothes made of a strong fabric and

avoid loose clothing that can catch on

twigs and branches. Always wear heavy ,

long pants. Do not wear jewelry, shorts

sandals or go barefoot. Secure hair so it is

above shoulder level.

Personal protective equipment

FIRST AID KIT

Always have a first aid kit nearby.

Machine’ s safety equipment

This section describes the machine’ s safe-

ty equipment, its purpose, and how checks

and maintenance should be carried out to

ensure that it operates correctly. See the

“Know your trimmer ” section to locate

where this equipment is positioned on your

machine.

The life span of the machine can be reduced

and the risk of accidents can increase if

machine maintenance is not carried out

correctly and if service and/or repairs are not

carried out professionally. If you need further

information please contact your nearest ser-

vicing dealer .

Stop switch

Make sure the engine stops when you push

and hold the stop switch.

W ARNING: Never use a machine

that has faulty safety equipment!

Carry out the inspection, mainte-

nance and service routines listed in

this section.

Cutting a ttachment guard

This guard is intended to prevent loose ob-

jects from being thrown towards the opera-

tor. The guard also protects the operator

from accidental contact with the cutting at-

tachment.

W ARNING: Never use a cutting

attachmen t without an approved

guard. See the section on “T echnical

data”. If an incorrect or faulty guard

is fitted this can cause serious

personal injury .

WARNING: Whenever you use a

clearing saw, brushcutter or trimmer

you mus t wear personal protective

equipmen t that is approved by the

authorities. Personal protective

equipmen t does not eliminate the risk

of accidents, but it can reduce the ef-

fects of an injury in the event of an

accident. Ask your dealer for help

when choosi ng protective equipmen t.

IMPORTANT! Listen for warning signals

or shouts when you are wearing hearing

protection. Always remove your hearing

protection as soon as the engine stops.

English---5

115374427 Rev. 6 5/15/12

SAFETY INSTRUCTIONS

Use o

incorrectly wound trimmer line or an

incorrect cutting attachment increases the

level of vibration.

Muffler

The muffler is designed to reduce the noise

level and to direct the exhaust gases away

from the operator.

CAUTION! Muffler is fitted with a catalytic

converter designed to reduce exhaust gas

emissions.

For mufflers, it is very important that you fol-

low the instructions on checking, maintain-

ing, and servicing your machine.

See Checking, maintaining and servicing the

machine’s safety equipment section.

W ARNING: Overexposure to

vibration can lead to circulatory

damage or nerve damage in people

whohaveimpairedcirculation.

Contact your doctor if you experi-

ence symptoms of overexposure to

vibration. Such symptoms include

numbnes s, loss of feeling, tingling,

pricking, pain, loss of strength,

changes in skin color or condition.

These symptoms normally appear

in the fingers, hands or wrists. The

risk increases at low temperatures.

Cutting equipment

A trimm er head is intended for trimming

grass.

Checking, maintaining and

servicing the machine’s

safety equipment

IMPORTANT!

All servicing and repair work on the machine

requires special training. This is especially

true of the machine’s safety equipment. If

your machine fails any of the checks de-

scribed below you must contact your service

agent. When you buy any of our products we

guarantee the availability of professional re-

pairs and service. If the retailer who sells

your machine is not a servicing dealer, ask

him for the address of your nearest service

agent.

Stop switch

S Start the engine and make sure the engine

stops when you push and hold the stop

switch.

Cutting a ttachment guard

S Ensure that the guard is undamaged and

is not cracked.

S Replace the guard if it has been exposed

to impact or is cracked.

S Always use the recommended guard for

the cutting attachment you are using. See

section on “Technical data”.

W ARNING: The inside of the

muffler contain chemicals that may

be carcinogenic. Avoid contact

with these elements in the event of

a damaged muffler.

CAUTION: Mufflers fitted with cata-

lytic converters get very hot during use

and remain so for some time after stop-

ping. This also applie s at idle speed. Con-

tact can result in burns to the skin. Re-

membertheriskoffire!

W ARNING: Engine exhaust

fumes contain carbon monoxide,

which can cause carbon monoxide

poisoning. DO NOT

start or run the

machin e indoors, or anywhere that

is poorly ventilated. The exhaust

fumes from the engine are hot and

may contain sparks which can start

a fire. Never start the machine in-

doors or near combustible material!

English---6

115374427 Rev. 6 5/15/12

SAFETY INSTRUCTIONS

Muffler

S Never use a machine that has a faulty

muffler .

S Regularly check that the muffler is securely

attached to the machine.

S The muf fler on this unit is equipped with a

special spark arrestor mesh. The mesh

should be checked and, if necessary .

cleaned by a servicing dealer. A blocked

mesh will cause the machine to overheat,

which can lead to serious damage. Never

use a muffler with a defective spark arres-

tor mesh. See the Maintenance section.

Cutting equipment

This section describes how to choose and

mainta in your cutting equipm ent in order to:

S Obtain maximum cutting performance.

S Extend the life of cutting equipment.

General rules

1. Only use cutting attachm ents with the

guards we recommend! See the section

on “Technical Data”.

2. Check the cutting attachment for damage

or cracks. A damaged cutting attachment

should always be replaced.

IMPORT ANT!

This section describes how to choose and

mainta in your cutting equipm ent in order to:

Obtain maximum cutting performance.

Extend the life of cutting equipment.

Only use cutting attachments with the guards

we recommend! See the section on

“Technical data”.

Refer to the instructions for the cutting attach-

ment to check the correct way to load the

trimmer line and the correct line diameter .

Trimmer he a d

S Only use the recommended cutting at-

tachments. See the section on “Technical

data”.

S Smaller machines generally require small

trimmer heads and vice versa. This is be-

cause when clearing using trimmer line the

engine must throw out the trimmer line ra-

dially from the trimmer head and overcome

the resistance of the grass being cleared.

S The length of the trimmer line is also im-

portant. A longer trimmer line requires

greater engine power than a shorter

trimmer line of the same diameter.

S Make sure that the cutter on the trimmer

guard is intact. This is used to cut the

trimmer line to the correct length.

S To increase the life of the trimmer line it

can be soaked in water for a couple of

days. This will make the line tougher so

that it lasts longer .

IMPORT ANT!

Always ensure the trimmer line is wound

tightly and evenly around the drum, other-

wise the machine will generate harmful

vibration.

W ARNING: Always stop the en-

gine before doing any work on the

cutting attachment. This continues

to rotate even after the throttle has

been released. Ensure that the

cutting attachment has stopped

completely and disconnect the

lead from the spark plug before

you start to w ork on it.

W ARNING: Never use a machine

with faulty safety equipm ent. The

machine’s safety equipment must be

checked and maintained as

described in this section. If your

machine fails any of these checks

contact your servicing dealer to get

it repaired. Use of a machine with

faulty safety equipm ent increa ses

the risk of serious personal injury to

the operator or others.

English---7

115374427 Rev. 6 5/15/12

SAFETY INSTRUCTIONS

Safety instructions regarding the

surroundings

S Never allow children to use the machine.

S Ensure no one comes closer than 50 feet

(15 meters) when working.

S Never allow anyone else to use the

machine without first ensuring that they

have understood the contents of the

operator’s manual.

Safety instru ctions before starting

work

S Inspect the working area. Remove any

objects such as stones, broken glass,

nails, steel wire, string, etc. that can be

thrown or can wrap around the cutting

head or shaft.

S Keep others at a safe distance. Children,

animals, onlookers and helpers should

stand outside of the safety zone of 50

feet (15 meters). Bystanders should be

encouraged to wear safety glasses. Stop

the machine immediately if anyone

should approach.

S Check the entire machine before starting

work. Replace damaged parts. Check for

fuel leakage and that all safety guards

and covers are complete and fastened

securely. Check all nuts and bolts.

S Check the cutting head

for cracks or any other

damage.

S Ensure the trimmer guard

is mounted and not

damaged.

Personal protection

S Always wear boots and

other equipment described

in the “Personal protective

equipment” section.

S Always wear working

clothes and heavy--duty

long pants.

S Never wear loose fitting

clothes or jewelry.

S Persons with long hair

should (for personal safety)

put their hair up.

General safety precautions

IMPORTANT!

S The machine is only designed for trimming

grass.

S The only accessories you can operate

with this engine unit are the cutting at-

tachments we recommend in the “Tech-

nical data” section.

S Never use wire, rope, string, etc.

S Never use the machine if you are tired, if

you have drunk alcohol, or if you are tak-

ing medication that could affect your vi-

sion, your judgment or your coordination.

S Never use the machine in extreme weath-

e r co ndi tio ns such as seve re co ld, very ho t

and/or humid climates.

S Never use a machine that has been modi-

fied in any way from its original specifica-

tion.

S Wear personal protective equipment. See

instructions in the “Personal protective

equipment” section.

S Never use a machine that is faulty . Carry

out the checks, maintenance and service

instructions described in this manual.

Some maintenance and service measures

must be carried out by trained and quali-

fied specialists. See instructions in the

“Maintenance” section.

S All covers and guards must be fitted before

starting. Make sure the spark plug cap and

lead are not damaged. Otherwise you

could get an electric shock.

S The machine operator must ensure that

no people or animals come closer than

50 feet (15 meters) while working.

S Stay clear of spinning line.

S Secure or remove loose clothing or cloth-

ing with loosely hanging ties, straps, tas-

sels, etc. They can be caught in moving

parts.

S Being fully covered also helps protect you

from debris and pieces of toxic plants

thrown by spinning line.

S Keep handles free of oil and fuel.

S Always keep the engine on the right hand

side of your body .

S Hold the unit firmly with both hands.

S Keep trimmer head below waist level and

away from all parts of your body. Do not

raise engine above your waist.

S Keep all parts of your body away from

muffler and spinning line. Keep engine be-

low waist level. A hot muffler can cause

serious burns.

S Keep firm footing and balance. Do not

overreach or use from unstable surfaces

such as ladders, trees, steep slopes, roof-

tops, etc.

S Use only in daylight or good artificial light.

S Use only for jobs explained in this manual.

WARNING: A faulty cutting at-

tachment may increase the risk of

accidents.

English---8

115374427 Rev. 6 5/15/12

SAFETY INSTRUCTIONS

S Check that the trimmer head and guard

are correctly secured.

S When adjusting the carburetor, make sure

the lower end is supported and that no one

is in the immediate vicinity.

S Make sure the cutting head does not rotate

when idling.

S Make sure the handle and safety features

are in order. Never use a machine that has

parts missing or has been changed in

relation to the specification.

S Only use the machine for the purpose for

which it was intended.

Starting

S Ensure that all of the engine covers and

housings are properly fitted before the unit

is started.

S Never start or attempt to run the unit with

the clutch, clutch drum, clutch cover, or

driveshaft removed.

S Never start the machine indoors. Exhaust

fumes can be dangerous if inhaled.

S Observe your surroundings and make sure

that there is no risk of people or animals

coming into contact with the cutting equip-

ment.

S See the “Starting and Stopping” section for

complete instructions.

Fuel safety

S Always use a fuel container with an anti--

spill valve.

S Never refuel the machine while the engine

is running.

S Always stop the engine and let it cool for a

few minutes before refueling.

S Make sure there is plenty of ventilation

when refueling or mixing fuel (gasoline and

2--stroke oil).

S Move the machine at least 10 feet (3 me-

ters) from the refueling point before start-

ing it.

S Never start the machine:

S If you have spilled fuel on it. Wipe off

the spillage and allow remaining fuel to

evaporate.

S If you have spilled fuel on yourself or

your clothes, change your clothes. Was

any part of your body that has come in

contact with fuel. Use soap and water.

WARNING: When the engine is

startedwiththechokeineitherthe

choke or start throttle positions the

cutting attachment will start to

rotate immediately.

Min. 10 ft.

(3 m)

S If the machine is leaking fuel. Check

regularly for leaks from the fuel cap

and fuel lines.

S Avoid all skin contact with fuel. Fuel is

a skin irritant and may even cause

skin changes.

Transporting and storage

S Store and transport the machine and fuel

so that there is no risk of any leakage or

fumes coming into contact with sparks or

naked flames, for example, from electri-

cal machinery , electric motors, electrical

relays/switches or boilers.

S When storing and transporting fuel al-

ways use approved containers intended

for this purpose.

S When storing the machine for long peri-

ods the fuel tank must be emptied. Con-

tact your local gas station to find out

where to dispose of excess fuel.

S Ensure the machine is cleaned and that

a complete service is carried out before

long--term storage.

General working instructions

IMPORTANT!

This section describes the basic safety pre-

cautions for working with trimmers. If you

encounter a situation where you are uncer-

tain how to proceed you should ask an ex-

pert. Contact your servicing dealer .

Avoid all usage which you consider to be

beyond your capability.

You must understand the dif ference between

forestry cle aring, grass cleari ng and grass

trimming before use.

Basic safety rules

1. Look around you:

S To ensure that people, animals or other

things cannot af fect your control of the

machine.

S To ensure that people, animals, etc.,

do not come into contact with the cut-

ting attachment or loose objects that

are thrown out by the cutting attach-

ment.

WARNING: T ake care when han-

dling fuel. Bear in mind the risk of

fire, explosion and inhaling fumes.

English---9

115374427 Rev. 6 5/15/12

SAFETY INSTRUCTIONS

3. M a ke sure yo u ca n mo ve and stan d safe ly.

Check the area around you for possible ob-

stacles (roots, rocks, branches, ditches, etc.)

in case you have to move suddenly. Take

great care when working on sloping ground.

4. Switch off the engine before moving to

another area.

5. Never put the machine down with the engine

running or while the cutting attachment is

rotating .

Basic working techniques

S Always slow the engine to idle speed after

each working operation. Long periods at

full throttle without any load on the engine

can lead to serious engine damage.

S It is recommended that the engine not

be operated for longer than 1 minute at

full throttle.

Grass tri mming using a trimmer head

Trimming

S Hold the trimmer head just above the

ground at an angle. It is the end of the trim-

mer line that does the work. Let the trim-

mer line work at its own pace. Never press

the trimmer line into the area to be cut.

S The trimmer line can easily remove grass

and weeds up against walls, fences, trees

and borders, however it can also damage

sensitive bark on trees and bushes, and

damage fence posts.

W ARNING: Sometime s branc hes

or grass get caught between the

guard and cutting attachment.

Always stop the engine before

cleaning.

S CAUTION! Do not use the machine

unless you are able to call for help in

the event of an accident.

2. Do not use the machine in bad weather ,

such as dense fog, heavy rain, strong

wind, intense cold, etc. W orking in bad

weather is tiring and often brings added

risks, such as icy ground, unpredictable

felling direction, etc.

S Reduce the risk o

damaging plants by

shortening the trimmer line to 4--4 1/2 inches

(10--12 cm) and reducing the engine speed.

S When tr imming you should use less than

full throttle so that the trimmer line lasts

longer and to reduce the wear on the

trimmer head.

Clearing

S The clearing technique removes all un-

wanted vegetation. Keep the trimmer

head just above the ground and tilt it. Let

the end of the trimmer line strike the

ground around trees, posts, statues and

the like. IMPORTANT! This technique

increases the wear on the trimmer line.

S The trimmer line wears quicker and must

be fed forward more often when working

against stones, brick, concrete, metal

fences, etc., than when coming into con-

tact with trees and wooden fences.

Cutting

S The trimmer is ideal for cutting grass that

is difficult to reach using a normal lawn

mower . Keep the trimmer line parallel to

the ground when cutting. Avoid pressing

the trimmer head against the ground as

this can ruin the lawn and damage the

tool.

S Do not allow the trimmer head to con--

stantly come into contact with the ground

during normal cutting. Constant contact

of this type can cause damage and wear

to the trimmer head.

English---10

115374427 Rev. 6 5/15/12

SAFETY INSTRUCTIONS

Sweeping

S The fan ef fect of the rotating line can be

used for quick and easy clearing up.

Hold the trimmer line parallel to and

above the area to be swept and move

the tool to and fro.

S When cutting and sweeping you should

use full throttle to obtain the best results.

WARNING: Watch out for

thrown objects. Always wear

approved eye protection. Never

lean over the cutting attachment

guard. Stones, rubbish, etc. can be

thrown up into the eyes causing

blindness or serious injury. Keep

unauthorised persons at a dis-

tance. Children, animals, onlookers

and helpers should be kept outside

the safety zone of 15 m. Stop the

machine immediately if anyone

approaches. Never swing the ma-

chine around without first checking

behind you to make sure no one is

within the safety zone.

WARNING: Sometimes

branches or grass get caught

between the guard and cutting

attachment or wrapped around the

shaft. Neither the operator of the

machine nor anyone else may at-

tempt to remove the cut material

while the engine is running or the

cutting equipment is rotating,

as this can result in serious injury.

Stop the engine and cutting equip-

ment before you remove material.

English---11

115374427 Rev. 6 5/15/12

KNOW YOUR TRIMMER

1. Trimmer head 8. Starter handle

2. Cutting attachment guard 9. Fuel tank

3. Shaft 10. Choke control

4. Loop handle 11. Air purge

5. Throttle control 12. Air filter cover

6. Stop switch 13. Handle adjustment

7. Cylinder cover 14. 2--stroke engine oil

15. Operator’s manual

What is what?

English---12

115374427 Rev. 6 5/15/12

ASSEMBLY

TE: Make sure unit is assembled cor-

rectly as shown in this manual.

Fittin g the loop handle

S Position the handle on the shaft. Note

that the handle must be mounted be-

tween the two arrows on the shaft.

S Fit the screw , securing plate and wing

nut as shown in the diagram.

S Tighten the wing nut.

Fitting the trimmer guard and

trimmer head

S Fit the correct trimmer guard (A) for use

with the trimmer head. Hook the trimmer

guard/combination guard onto the fitting on

the shaft and secure with the wing nut (B).

S Fit the dust cup (C) on the shaft. The nut

must be completely covered by the dust

cup.

S Hold the dust cup with a wrench to pre-

vent the shaft from rotating.

S Screw the trimmer head (D) onto the

shaft.

S To dismantle, follow the instructions in

the reverse order.

English---13

115374427 Rev. 6 5/15/12

FUEL HANDLING

Fuel mixture

CAUTION! The machine is equipped with

a two--stroke engine and must always be

run using a mixture of gasoline and two--

stroke engine oil. It is important to accu-

rately measure the amount of oil to be

mixed to ensure that the correct mixture is

obtained. When mixing small amounts of

fuel, even small inaccuracies can drastical-

ly affect the ratio of the mixture.

Gasoline

CAUTION! Always use high quality

unleaded gasoline.

S This engine is certified to operate on

unleaded gasoline.

S The lowest recommended octane rating

is 87. If you run the engine on lower oc-

tane rating than 87, “knocking” can oc-

cur. This leads to an increased engine

temperature, which can result in a seri-

ous engine breakdown.

S When working at continuous high revs a

higher octane rating is recommended.

Two -- stroke oil

S For great results and performance use

HUSQV ARNA two--stroke oil, which is

specially formulated for our two--stroke

engines. Mixture 1:50 (2%).

S To maximize the life of your trimmer, you

may choose to use a high quality syn-

thetic oil formulated for two--stroke

engines. Mixture 1:50 (2%).

S Never use two--stroke oil intended for

water--cooled outboard engines,

sometimes referred to as outboard oil.

S Never use oil intended for four--stroke

engines.

W ARNING: Fuel and fuel fumes

are highly flammable and can cause

serious injury when inhaled or al-

lowed to come in contact with the

skin. For this reason, observe cau-

tion when handling fuel and make

sure there is adequa te ve ntilation.

U.S. gallon U.S. fl. oz.

121/2

2 1/2 6 1/2

5127/8

Gasoline

Two -- stroke oil

2% (1:50)

S Always start by flling half the amount of the

gasoline to be used. Then add the entire

amount of oil. Mix (shake) the fuel mixture.

Add the remaining amount of gasoline.

S Mix (shake) the fuel mixture thoroughly

before filling the machine’ s fuel tank.

S Do not mix more than one month’s sup-

ply of fuel at a time.

S If the machine is not used for some time,

the fuel tank should be emptied and

cleaned.

W ARNING: The catalytic convert-

er muffler gets very hot during and

after use. This also applies during

idling.Beawareofthefirehazard,

especially when working near flam-

mable substances and/or vapors.

Fueling

WARNING: Taking the following

precautions, will lessen the risk of

fire:

Do not smoke or place hot objects

near fuel.

Always shut off the engine before

refueling.

Always stop the engine and let it

cool for a few minutes before re-

fueling.

When refueling, open the fuel cap

slowly so that any excess pressure

is released gently.

Tighten the fuel cap carefully after

refueling.

Always move the machine away

from the refueling area before

starting.

Min. 10 ft.

(3 m)

S Clean the area around the fuel cap.

Contamination in the tank can cause

operating problems.

S Ensure that the fuel is well mixed by shak-

ing the container before filling the tank.

Mixing

S Always mix the gasoline and oil in a

clean container intended for fuel.

English---14

115374427 Rev. 6 5/15/12

STARTING AND STOPPING

Check before starting

S Inspect the unit before each use. Re-

place damaged parts. Check for fuel

leaks. Make sure all fasteners are in

place and secure. Make sure the cutting

attachment is properly installed and se-

curely fastened. Use only flexible, non-

metallic line recommended by the

manufacturer. Never use, for example,

wire or wire rope, which can break off

and become a dangerous projectile.

S Check that the trimmer head and trimmer

guard are not damaged or cracked.

Replace the trimmer head or trimmer

guard if they have been exposed to

impact or are cracked.

S Never use the machine without a guard

nor with a defective guard.

Starting and stopping

W ARNING: The complete clutch,

clutch cover , and shaft must be

fitted before the machine is started,

otherwise parts could come loose

and cause personal injury .

Always move the machine away

from the refueling area before

starting. Place the machine on a

flat surface. Ensure the cutting at-

tachment cannot come into contact

with any object.

Make sure no unauthorized persons

are in the working area, otherwise

there is a risk of serious personal

injury . The safety distance is 50 feet

(15 meters).

Cold engine

Primer bulb: Press the primer bulb 10

times until fuel begins to fill the bulb. The

primer bulb need not be completely filled.

Choke: Move the blue engine choke lever

to the closed position.

Starting

Hold the body of the machine on the

ground using your left hand (CAUTION!

Not with your foot!).

Firmly grip the starter rope handle with

your right hand. DO NOT squeeze

throttle trigger. Slowly pull out the cord

until you feel some resistance (the starter

pawls grip); then quickly and powerfully

pull the cord.

Never wrap the starter cord around

your hand.

Repeat pulling the cord until the engine

attempts to start. Move the blue engine

choke lever to the ½ position. Pull starter

rope until engine runs. Move the blue en-

gine choke lever to the opened position.

NOTE: If engine dies, return blue engine

choke lever to the closed position and

repeat starting steps.

CAUTION! Do not pull the starter cord all

the way out and do not let go of the starter

handle when the cord is fully extended.

This can damage the machine.

English---15

115374427 Rev. 6 5/15/12

STARTING AND STOPPING

Warm engine

With a warm engine, move the blue engine

choke lever to the ½ position. Pull starter

rope until engine runs. Move the blue

engine choke lever to the opened position.

W ARNING: When the engine is

started with the choke in the closed

position the cutting attachment will

start to rotate immediately.

Stopping

Stop the engine by pushing and holding

the stop switch in the STOP position until

the engine stops.

MAINTENANCE

Carburetor

Your Husqvarna product has been designed

and manufactured to specifications that re-

duce harmful emissions. After the engine

has used 8--10 tanks of fuel, the engine will

be run--in. To ensure that it continues to run

at peak performance and to minimize harm-

ful exhaust emissions after the run--in peri-

od, ask your servicing dealer to adjust your

carburetor.

The owner is responsible for the per

or-

mance of all required maintenance as

defined in the operator’s manual.

W ARNING: The complete clutch,

clutch cover , and shaft must be

fitted before the machi ne is started,

otherwise parts could come loose

and cause personal injury .

Function

S The carburetor governs the engine’s

speed via the throttle control. Air and fuel

are mixed in the carburetor.

S The T--screw regulates the throttle setting

at idle speed. If the T--screw is turned

clockwise this gives a higher idle speed;

turning it counterclockwise gives a lower

idle speed.

Basic setting

S The basic carburetor settings are ad-

justed during testing at the factory. Fine

adjustment should be carried out by a

skilled technician.

CAUTION! If the cutting attachment rotates

when the engine is idling the idle adjustment

screw T should be turned counterclockwise

until the cutting attachment stops.

W ARNING: The cutting attach-

ment ma y be spinning during carbu-

retor adjustme nts. Wear your protec-

tive equipment and observe all safe-

ty instructions . Be sure the cutting

attachm ent stops turning when the

engine idles. When the unit is turned

off, make sure the cutting attach-

ments has stopped before the unit is

set down.

Rec. idle speed:

See “Technical data” section.

Recommended max. speed:

See “Technical data” section.

Fine adjustment of the idle speed--T

Adjust the idle speed using the idle adjust-

ment screw--T if it is necessary to readjust.

First, turn the idle adjustment screw--T

clockwise until the cutting attachment starts

to rotate. Then, turn the screw counterc-

lockwise until the cutting attachment stops.

The idle speed is correctly adjusted when

the engine will run smoothly in every posi-

tion. The idle speed should also be well

below the speed at which the cutting at-

tachment starts to rotate.

Idle Speed

Screw--T

WARNING: Improper mainte-

nance could result in serious engine

damage or in serious injury .

English---16

115374427 Rev. 6 5/15/12

MAINTENANCE

W ARNING: If the idle speed can-

not be adjusted so that the cutting

attachment stops, contact your ser-

vicing dealer . Do not use the ma-

chine until it has been correctly ad-

justed or repaired.

Unit/Maintenance Safety

Disconnect the spark plug before perform-

ing maintenance, except carburetor adjust-

ments.

Muffler

CAUTION! Muffler is fitted with a catalytic

converter designed to reduce exhaust gas

emissions.

The muffler is designed to reduce the noise

level and to direct the exhaust gases away

from the operator. The exhaust gases are

hot and can contain sparks, which may

cause fire if directed against dry and com-

bustible material.

Mufflers are equipped with a special spark

arrestor mesh. The mesh should be

checked and, if necessary. cleaned by a

servicing dealer. If the mesh is damaged,

it should be replaced. Ifthemeshisfre-

quently blocked, this can be a sign that the

performance of the catalytic converter is

impaired. Contact your servicing dealer to

inspect the muffler. A blocked mesh will

cause the machine to overheat and result

in damage to the cylinder and piston.

CAUTION! Never use a machine that has

a faulty or loose muffler. Ensure the muffler

bolts are tight.

Muffler bolts

Spark plug

The spark plug condition is influenced by:

S Incorrect carburetor adjustment.

S An incorrect fuel mixture (too much or in-

correct type of oil).

S A dirty air filter .

These factors cause deposits on the spark

plug electrodes, which may result in operat-

ing problems and starting difficulties.

If the machine is low on power, difficult to

start or runs poorly at idle speed: always

check the spark plug first before taking

any further action. If the spark plug is dirty,

clean it and check that the electrode gap is

0.024″ (0.6 mm). The spark plug should be

replaced after about a month in operation or

earlier if necessary.

CAUTION! Always use the recommended

spark plug type! Use of the wrong spark

plug can damage the piston/cylinder.

0.024″ (0.6 mm)

Spark arrestor mesh

W ARNING: The inside of the

muffler contain chemicals that may

be carcinogenic. Avoid contact

with these elements in the event of

a damaged muffler.

CAUTION: Mufflers fitted with cata-

lytic converters get very hot during use

and remain so for some time after stop-

ping. This also appli es at idle speed. Con-

tact can result in burns to the skin. Re-

member the risk of fire!

WARNING: Engine exhaust

fumes contain carbon monoxide,

which can cause carbon monoxide

poisoning. DO NOT

start or run the

machine indoors, or any where that

is poorly ventilated. The exhaus t

fumes from the engine are hot and

may contain sparks which can start

a fire. Never start the machine in-

doors or near combustible material!

English---17

115374427 Rev. 6 5/15/12

MAINTENANCE

Air filter

The air filter must be regularly cleaned to

remove dust and dirt in order to avoid:

S Carburetor malfunctions

S Starting problems

S Loss of engine power

S Unnecessary wear to engine parts

S Excessive fuel consumption

Clean the filter every 25 hours, or more

regularly if conditions are exceptionally

dusty.

Cleaning the air filter

Remove the air filter cover and take out the

filter. Wash it clean in warm, soapy water .

Rinse thoroughly. Ensure that the filter is dry

before refitting it.

An air filter that has been in use for a long

time cannot be cleaned completely. The

filter must therefore be replaced with a new

one at regular intervals. A damaged air

filter must always be replaced.

Maintenance schedule

Below you will find some general mainte-

nance instructions.

Daily maintenance

S Check throttle trigger and throttle trigger

lockout function.

S Check that the stop switch works

correctly.

S Check that there are no fuel leaks from

the engine, tank or fuel lines.

S Check that the cutter does not rotate

when the engine is idling.

S Clean the outside of the machine.

S Check that the harness is not damaged.

S Check that the blade guard is not dam-

aged or cracked.

S Replace the blade guard if it is exposed to

impact or is cracked.

S A non--balanced trimmer head induces

heavy vibrations that may damage the

machine.

S Check that nuts and screws are tight.

S Check that the trimmer head is tight.

Weekly maintenance

S Check the starter and starter cord.

S Clean the carburetor area.

S Clean the outside of the spark plug. Re-

move it and check the electrode gap. Ad-

just the gap to 0.024″ (0.6 mm), or

replace the spark plug. Use resistor spark

plug Champion RCJ--8Y or equivalent.

S Clean the cooling fins on the cylinder and

check that the air intake near the starter

is not blocked.

S Clean the air filter.

Monthly maintenance

S Clean the fuel tank.

S Clean the outside of the carburetor and

the space around it.

S Clean the fan and the area around it.

S Check fuel lines for cracks or other dam-

age. Change if necessary .

S Change the fuel filter in fuel tank.

S Check the clutch, clutch springs and the

clutch drum for wear. Replace if neces-

sary.

S Check electrical wires and connections.

S Replace the spark plug. Use resistor

spark plug Champion RCJ--8Y or equiva-

lent.

S Change the air filter.

English---18

115374427 Rev. 6 5/15/12

Trimmer Head Line Loading Instructions

English---19

115374427 Rev. 6 5/15/12

TECHNICAL DATA

Model 124C (3/8 RH arbor shaft thread)

Approved accessories Type Cutting attachment guard, part. no.

Trimmer head T25C 537 33 83--03

Technical data

124C

Engine

Cylinder volume, cu.in./cm

1.7/28

Cylinder bore, inch/mm 1.4/35

Stroke, inch/mm 1.130/28.7

Idle speed, rpm 2,800--3,200

Recommended max. speed, rpm 1 1 ,000

Speed of output shaft, rpm 8,000

Max. engine output, acc. to ISO 8893, hp/kW 1.1/0.8

Catalytic converter muffler Yes

Speed--regulated ignition system No

Ignition system

Manufacturer/type of ignition system Walbro/CD

Spark plug Champion RCJ--6Y

Electrode gap, inch/mm 0.024/0.6

Fuel and lubrication system

Manufacturer/type of carburetor Zama

Fuel tank capacity, US pint/liter 0.85/0.4

Weight

Weight without fuel, cutting attachment and guard, lbs/kg 10/4.4

Sound levels

(see note 1)

Equivalent sound pressure level at the user’s ear,

measured according to ANSI B175.3--1997, dB(A),

min/max: 94/97

Vibration levels

Vibration levels at handles, measured according to

ANSIB175.3--1997, m/s

At idle, left/right handles: 3/5

At max. speed, left/right handles: 9/8

NOTE! This spark ignition system complies with the Canadian standard ICES--002.

Note 1: Equivalent noise pressure level is calculated as the time--weighted energy total for

noise pressure levels under various working conditions with the following time distribution:

1/2 idle and 1/2 max. speed.

NOTE! Noise pressure at the user’s ear and vibration on the handles are measured with all

the machine’s approved cutting equipment fitted. The table indicates the highest and lowest

values.

English---20

115374427 Rev. 6 5/15/12

U.S. EPA / CALIFORNIA / ENVIRONMENT CANADA

EMISSION CONTROL WARRANTY STATEMENT

IMPORTANT: This product is compliant

with U.S. EPA Phase 3 regulations for

exhaust and evaporative emissions.

To ensure EP A Phase 3 compliance, we

recommend using only genuine HUSQV ARNA

b ra nd repla cement parts. Use of non-

compliant replacements parts is a

violation of federal law.

YOUR WARRANTY R IGHTS AND

OBLIGATIONS:

The U.S. Environmental Protection Agency,

Californi a Air Resources Board, Enviro nme nt

Canada and HUSQV ARNA are pleased to ex-

plain the emissions control system warranty on

your year 2012 and later small off--road engine.

In California, all small off--road engines must

be designed, built, and equipped to meet the

State’s stringent anti--smog standards.

HUSQVARNA must warrant the emission con-

trol system on your small off--road engine for

the periods of time listed below provided there

has been no abuse, neglect, or improper main-

tenance of your small off--road engine. Y our

emission control system includes parts such

as the carburetor , the ignition system and

the fuel tank. Where a warrantable condition

exists, HUSQV ARNA will repair your small

off--road engine at no cost to you. Expenses

covered under warranty include diagnosis,

parts and labor.

MANUFA CTURER’S WARRANTY

COVERAGE:

If any emissions related part on your engine

(as listed under Emissions Control Warran-

ty Parts List) is defective or a defect in the

materials or workmanship of the engine

causes the failure of such an emission re-

lated part, the part will be repaired or re-

placed by HUSQVARNA.

OWNER’S WARRANTY RESPONSI-

BILITIES:

As the small off--road engine owner, you are

responsible for the performance of the re-

quired maintenance listed in your operator’s

manual. HUSQVARNA recommends that

you retain all receipts covering maintenance

on your small off--road engine, but HUSQ-

VARNA cannot deny warranty solely for the

lack of receipts or for your failure to ensure

the performance of all scheduled mainte-

nance. As the small off--road engine owner ,

you should be aware that HUSQV ARNA

may deny you warranty coverage if your

small of f--road engine or a part of it has

failed due to abuse, neglect, improper main-

tenance, unapproved modifications, or the

use of parts not made or approved by the

original equipment manufacturer .

WARRANT Y C OMMEN CEMENT

DATE:

The warranty period begins on the date the

small off--road engine is purchased.

LENGTH OF C OVERAGE:

This warranty shall be for a period of two

years from the initial date of purchase, or

until the end of the product warranty (which-

ever is longer).

WHAT IS COVERED: REPAIR OR

REPLACEMENT OF PARTS.

Repair or replacement of any warranted

part will be performed at no charge to the

owner at an approved HUSQVARNA ser-

vicing center. If you have any questions re-

garding your warranty rights and responsi-

bilities, you should contact your nearest au-

thorized service center, call HUSQVARNA

at 1--800--487--5951, or visit

www.husqvarna.com

WARRANT Y PER IOD:

Any warranted part which is not scheduled

for replacement as required maintenance,

or which is scheduled only for regular in-

spection to the effect of “repair or replace

as necessary” shall be warranted for 2

years. Any warranted part which is sched-

uled for replacement as required mainte-

nance shall be warranted for the period of

time up to the first scheduled replacement

point for that part.

DIAGNOSIS:

The owner shall not be charged for diag-

nostic labor which leads to the determina-

tion that a warranted part is defective if the

diagnostic work is performed at an ap-

proved HUSQVARNA servicing center .

CONSEQUENTIAL DAMAGES:

HUSQVARNA may be liable for damages to

other engine components caused by the fail-

ure of a warranted part still under warranty .

WHAT IS NOT COVERED:

All failures caused by abuse, neglect, or

improper maintenance are not covered.

ou are responsible

or presenting your

small of f--road engine to a HUSQV ARNA

authorized repair center as soon as a prob-

lem exists. Warranty repairs should be com-

pleted in a reasonable amount of time, not to

exceed 30 days. If you have any questions

regarding your warranty rights and responsibi-

lities, you should contact your nearest autho-

rized servi ce cen t e r, call HUSQVARNA at

1--800--487--5951, or visit

www.husqvarna.com

La page charge ...

Husqvarna 124L Manuel utilisateur

Marque: Husqvarna

Modèle: 124L

Catégorie: Coupe-herbe

Taper: Manuel utilisateur

Ce manuel convient également à

124C

Télécharger le PDF

rapport

dans d''autres langues

English: Husqvarna 124L User manual
español: Husqvarna 124L Manual de usuario

Husqvarna 124L Manuel utilisateur

Ce manuel convient également à

Husqvarna 124L Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents