Whirlpool YMED7000XW2 Guide d'installation

Marque: Whirlpool

Modèle: YMED7000XW2

Catégorie: Sèche-linge

Taper: Guide d'installation

GAS DRYER INSTALLATION INSTRUCTIONS

CANADIAN ELECTRIC DRYER INSTRUCTIONS

INSTRUCTIONS POUR L'INSTALLATION DE LA St_CHEUSE

GAZ (I_.-U. ET CANADA)

I_LECTRIQUE (CANADA UNIQUEMENT)

Table of Contents

DRYER SAFETY .......................................................................... 2

iNSTALLATiON REQUIREMENTS .............................................. 4

Tools and Parts ...................................................................... 4

LOCATION REQUIREMENTS ..................................................... 5

ELECTRIC DRYER POWER HOOKUP-CANADA ONLY ........... 6

GAS DRYER POWER HOOKUP ................................................. 7

iNSTALL LEVELING LEGS .......................................................... 9

MAKE GAS CONNECTION ......................................................... 9

VENTING .................................................................................... 10

Venting Requirements ......................................................... 10

Plan Vent System ................................................................. 11

Install Vent System .............................................................. 12

CONNECT iNLET HOSE ........................................................... 12

CONNECT VENT ....................................................................... 14

LEVEL DRYER ........................................................................... 14

COMPLETE iNSTALLATiON CHECKLIST ............................... 15

DOOR REVERSAL (OPTIONAL) ............................................... 15

Table des mati_res

SECURITE DE LA SECHEUSE..................................................19

EXIGENCES D'INSTALLATION ................................................. 21

Outillage et pi_ces ............................................................. 21

EXIGENCES D'EMPLACEMENT ............................................... 22

SLeCHEUSE leLECTRIQUE RACCORDEMENT A

UALIMENTATION leLECTRIQUE - CANADA SEULEMENT ..... 23

RACCORDEMENT D'UNE SLeCHEUSE A GAZ ........................ 24

iNSTALLATiON DES PIEDS DE NIVELLEMENT ...................... 26

iNSTRUCTiONS POUR LE RACCORDEMENT AU GAZ ......... 26

EVACUATION ............................................................................. 27

Exigences concemant I'_vacuation ................................. 27

Planification du syst_me d'_vacuation ............................ 28

Installation du syst_me d'_vacuation ............................... 30

RACCORDEMENT DES TUYAUX D'ALIMENTATION .............. 30

RACCORDEMENT DU CONDUIT DqeVACUATION ................. 32

R(--GLAGE DE L'APLOMB DE LA Si'-=CHEUSE.......................... 32

ACHEVER UINSTALLATION LISTE DE Vi_RIFICATION ........... 33

iNVERSiON DE LA PORTE (FACULTATIF) ................................ 33

Para una version de estas instrucciones en espa_ol, visite www.Whirlpool.com

iNSTALLATiON NOTES

Date of purchase:

Date of installation:

Installer:

Model number:

Serial number:

NOTES CONCERNANT L'INSTALLATION

Date d'achat:

Date d'installation:

Installateur:

Num_ro de module:

Num_ro de s_rie:

W10423115A

W10423116A =SP

DRYER S_ETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

WARNING - ...i.. ofFi,o..

- Clothes dryer installation must be performed by a qualified installer.

- install the clothes dryer according to the manufacturer's instructions and local codes,

= Do not install a clothes dryer with fle×ible plastic venting materials or flexible metal

(foil type) duct. if fle×ible metal duct is installed, it must be of a specific type identified

by the appliance manufacturer as suitable for use with clothes dryers. Fle×ible venting

materials are known to collapse, be easily crushed, and trap lint. These conditions will

obstruct clothes dryer airflow and increase the risk of fire.

= To reduce the risk of severe injury or death, follow all installation instructions.

= Save these instructions.

WARNING: For your safety, the information in this manual must be followed to minimize 1

the risk of fire or explosion, or to prevent property damage, personal injury, or death. 1

- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this

or any other appliance.

- WHAT TO DO iF YOU SMELL GAS:

o Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone in your building.

®Clear the room, building, or area of all occupants.

• Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's

instructions.

= if you cannot reach your gas supplier, call the fire department.

- Installation and service must be performed by a qualified installer, service agency, or

the gas supplier.

WARNING: Gas leaks cannot always be detected by smell.

Gas suppliers recommend that you use a gas detector approved by UL or CSA.

For more information, contact your gas supplier.

If a gas leak is detected, follow the "What to do if you smell gas" instructions.

iMPORTANT: The gas installation must conform with local codes, or in the absence of local codes, with the National Fuel Gas

Code, ANSi Z223.1/NFPA 54 or the Canadian Natural Gas and Propane Installation Code, CSA B149.1.

The dryer must be electrically grounded in accordance with local codes, or in the absence of local codes, with the National

Electrical Code, ANSI/NFPA 70 or Canadian Electrical Code, CSA C22.1.

in the State of Massachusetts, the following installation instructions apply:

[] Installations and repairs must be performed by a qualified or licensed contractor, plumber, or gasfitter qualified or licensed by

the State of Massachusetts.

[] if using a ball valve, it shall be a T-handle type.

[] A flexible gas connector, when used, must not exceed 3 feet.

IMPORTANT: When discarding or storing your old clothes dryer, remove the door.

INSTALLATION REQUIREMENW$

TOOLS AND PARTS

Gather the required tools and parts before starting installation.

Tools needed for all installations:

Tools needed for gas installations:

Flat-blade screwdriver

1/4" and 5/16" nut driver

recommended)

Tape measure

#2 Phillips screwdriver

Level

Pliers

8" or 10" pipe wrench 8" or 10" adjustable wrench

(for gas connections)

Pipe-joint compound

resistant to LP gas

Parts supplied:

Parts package is located in dryer drum. Check that all parts

are included.

NOTE: Do not use leveling legs supplied with dryer if installing

with a pedestal or a stack kit.

Leveling legs (4)

Utility knife

Caulking gun and compound

(new vent installations)

Tin snips (new vent

installations)

Adjustable wrench that

opens to 1" (25 mm) or

hex-head socket wrench

Min. 8" long Torx°* T25

screwdriver

(for door reversal only)

1 ® TORX is a registered trademark of Saturn Fasteners, Inc.

Short inlet hose

Rubber washers

Long inlet hose

"Y" connector

Parts needed: (Not supplied with dryer)

[] Vent clamps

[] Vent elbows and ductwork

Additional parts may be required, depending in your installation.

Check local codes. Check existing electrical supply and venting.

Read "Electrical Requirements" and "Venting Requirements"

before purchasing parts.

Optional Equipment: (Not supplied with dryer)

Refer to your "Use and Care Guide" for information about

accessories available for your dryer.

LOCATION REQUIREMENW$

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from dryer.

Place dryer at Jeast 18 inches (460 ram) above the floor

for a garage installation.

Failure to do so can result in death, explosion, or fire.

You will need:

[] A location allowing for proper exhaust installation.

See "Venting Requirements."

[] A separate 15 or 20 amp circuit for a gas dryer or 30 amp

circuit for an electric dryer.

[] If using power supply cord, a grounded electrical outlet

located within 2 ft. (610 mm) of either side of dryer.

See "Electrical Requirements".

[] Floor must support dryer weight of 200 Ibs. (90.7 kg).

Also consider weight of companion appliance.

[] Cold water faucets located within 4 ft. (1.2 m) of the water

fill valves, and water pressure of 20 - 120 psi (138 - 827 kPa).

You may use the water supply for your washer using the

"Y" connector and short hose (if needed) which are provided.

[] Level floor with maximum slope of 1" (25 mm) under entire

dryer. If slope is greater than 1" (25 mm), install Extended

Dryer Feet Kit, Part Number 279810. If not level, clothes

may not tumble properly and automatic sensor cycles may

not operate correctly.

[] For garage installation, place dryer at least 18" (460 mm)

above floor, if using a pedestal, you will need 18" (460 mm)

to bottom of dryer.

[] The dryer must not be installed or stored in an area where

it will be exposed to water and/or weather.

iMPORTANT: Do not operate, install, or store dryer where

it will be exposed to water, weather, or at temperatures below

40° F (4° C). Lower temperatures may cause dryer not to

shut off at end of automatic sensor cycles, resulting in longer

drying times.

DRYER DiMENSiONS

Front view:

381/8 H

(968 ram)

3/411 _

(18 ram)

(686 ram)

* Approx. measurement

Side view:

507/8"

(1292 turn)

311/8"

{790 rnrn)

3/4_I*

{18 ram}

53/4 ll*

(146 turn}

J 31/2,,

(257 ram)

* Approx. measurement

Back view:

53/4 mm_

(146 ram) Vent

3/411"#

(18 ram)

Water inlet

-V

, T.....

•,91--143/8"_

(365 ram)

253/4"-ii--_

(654 ram}

61/4"

(159 ram}

297/8"*

(759 ram}

.I1- 61/8,,. _

(156 ram)

Approx. measurement

NOTE: Most installations require a minimum of 5" (127 mm) clearance

behind dryer for exhaust vent with elbow. See "Venting Requirements".

Installation Clearances

For each arrangement, consider allowing more space for ease

of installation and servicing; spacing for companion appliances

and clearances for walls, doors, and floor moldings. Space

must be large enough to allow door to fully open. Add spacing

on all sides of dryer to reduce noise transfer. If a closet door

or Iouvered door is installed, top and bottom air openings

in door are required.

Check code requirements. Some codes limit, or do not permit,

installation of the dryer in garages, closets, mobile homes, or

sleeping quarters. Contact your local building inspector.

NOTE: No other fuel-burning appliance can be installed in the

same closet as a dryer.

installation spacing for recessed area

or closet installation

All dimensions show recommended and minimum spacing

allowed.

[] Additional spacing should be considered for ease of

installation and servicing.

[] Additional clearances might be required for wall, door, floor

moldings, dryer venting, and gas line.

[] Additional spacing should be considered on all sides

of the dryer to reduce noise transfer.

[] For closet installation, with a door, minimum ventilation

openings in the top and bottom of the door are required.

Louvered doors with equivalent ventilitation openings are

acceptable.

[] Companion appliance spacing should also be considered.

Recommended installation clearances {dryer only):

Mobile home installations require:

[] Metal exhaust system hardware, available for purchase from

your dealer. For further information, see "Assistance or

Service" section in your "Use and Care Guide".

[] Special provisions must be made in mobile homes to

introduce outside air into dryer. Openings (such as a nearby

window) should be at least twice as large as dryer exhaust

opening.

For mobile home installation of gas dryers:

[] Mobile Home Installation Hold-down Kit Part Number 346764

is available to order. For further information, see "Assistance

or Service" section in your "Use and Care Guide".

ELECTRIC DR R

FOWER HOOKUFo ONLY

ELECTRICAL REQUIREMENTS

Electrical Shock Hazard

Plug into a grounded 4 prong outlet,

Failure to do so can result in death or electrical shock.

', "':-=2

5 n * i i,

(127 rnrn} "

(76 ram)

* 0" (0 mm) spacing is allowed.

Mobile home =Additional installation requirements:

This dryer is suitable for mobile home installations. The

installation must conform to the Manufactured Home

Construction and Safety Standard, Title 24 CFR, Part 3280

(formerly the Federal Standard for Mobile home construction

and Safety, Title 24, HUD Part 280) or Standard CAN/CSA-Z240

MH.

It is your responsibility:

[] To contact a qualified electrical installer.

[] To be sure that the electrical connection is adequate and in

conformance with Canadian Electrical Code, C22.1-1atest

edition and all local codes. A copy of above codes standard

may be obtained from: Canadian Standards Association,

178 Rexdale Blvd., Toronto, ON M9W 1R3 CANADA.

[] To supply the required 4 wire, single phase, 120/240 volt,

60 Hz, AC only electrical supply on a separate 30-amp circuit,

fused on both sides of the line. A time-delay fuse or circuit

breaker is recommended. Connect to an individual branch

circuit.

[]

This dryer is equipped with a CSA

International Certified Power Cord

intended to be plugged into a standard

14-30R wall receptacle. The cord is 5 ft.

(1.52 m) long. Be sure wall receptacle is

within reach of dryer's final location.

4-wire receptacle

(14-30R)

If using a replacement power supply cord, it is recommended that

you use Power Supply Cord Replacement Part Number 8529008.

For further information, please reference service numbers located

in "Assistance or Service" section of your "Use and Care Guide".

GROUNDING INSTRUCTIONS

[] For a grounded, cord-connected dryer:

This dryer must be grounded. In the event of malfunction or

breakdown, grounding will reduce the risk of electric shock

by providing a path of least resistance for electric current.

This dryer is equipped with a cord having an equipment-

grounding conductor and a grounding plug. The plug must

be plugged into an appropriate outlet that is properly

installed and grounded in accordance with all local codes

and ordinances.

WARNING-" Improper connection of the equipment-

grounding conductor can result in a risk of electric shock.

Check with a qualified electrician or service representative

or personnel if you are in doubt as to whether the dryer is

properly grounded. Do not modify the plug provided with

the dryer: if it will not fit the outlet, have a proper outlet

installed by a qualified electrician.

SAVE THESE INSTRUCTIONS

GAS DR R FOWER HOOKUF

ELECTRICAL REQUIREMENTS

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

[] 120 Volt, 60 Hz, AC only, 15- or 20- amp fused electrical

supply is required. A time-delay fuse or circuit breaker is

recommended. It is also recommended that a separate circuit

serving only this dryer be provided.

GROUNDING INSTRUCTIONS

[] For a grounded, cord-connected dryer:

This dryer must be grounded. In the event of malfunction or

breakdown, grounding will reduce the risk of electric shock

by providing a path of least resistance for electric current.

This dryer is equipped with a cord having an equipment-

grounding conductor and a grounding plug. The plug must

be plugged into an appropriate outlet that is properly

installed and grounded in accordance with all local codes

and ordinances.

WARNinG-" improper connection of the equipment-

grounding conductor can result in a risk of electric shock.

Check with a qualified electrician or service representative

or personnel if you are in doubt as to whether the dryer is

properly grounded. Do not modify the plug provided with

the dryer: if it will not fit the outlet, have a proper outlet

installed by a qualified electrician.

SAVE THESE INSTRUCTIONS

GAS SUPPLY REQUIREMENTS

Explosion Hazard

Use a new CSA international approved gas supply line.

Install a shut=off valve.

Securely tighten all gas connections.

if connected to LP, have a qualified person make sure

gas pressure does not exceed 13" (330 ram)water

column.

Examples of a qualified person include:

licensed heating personnel,

authorized gas company personnel, and

authorized service personnel.

Failure to do so can result in death, explosion, or fire.

GAS TYPE

Natural Gas:

This dryer is equipped for use with Natural gas. It is design-

certified by CSA international for LP (propane or butane) gases

with appropriate conversion.

[] Your dryer must have the correct burner for the type of gas in

your home. Burner information is located on the rating plate in

the door well of your dryer. If this information does not agree

with the type of gas available, contact your dealer or call the

phone numbers referenced in the "Assistance or Service"

section of your "Use and Care Guide".

LP Gas Conversion:

iMPORTANT: Conversion must be made by a qualified

technician.

No attempt shall be made to convert the appliance from the gas

specified on the model/serial rating plate for use with a different

gas without consulting your gas company.

GASSUPPLYLiNE

Option 1 (Recommended Method)

Flexible stainless steel gas connector:

[] If local codes permit, use a new flexible stainless steel gas

connector (Design Certified by the American Gas Association

or CSA International) to connect your dryer to the rigid gas

supply line. Use an elbow and a 3/8" flare x 3/8" NPT adapter

fitting between the stainless steel gas connector and the dryer

gas pipe, as needed to prevent kinking.

Option 2 (Alternate Method)

Approved aluminum or copper tubing:

[] Must include 1/8" NPT minimum plugged tapping accessible

for test gauge connection, immediately upstream of the gas

connection to the dryer. See illustration.

[] 1/2" IPS pipe is recommended.

[] 3/8"approved aluminum or copper tubing is acceptable for

lengths under 20 ft. (6.1 m) if local codes and gas supplier

permit.

[] If you are using Natural gas, do not use copper tubing.

[] Lengths over 20 ft. (6.1 m) should use larger tubing and

a different size adapter fitting.

[] If your dryer has been converted to use LP gas, 3/8" LP

compatible copper tubing can be used. If the total length of the

supply line is more than 20 ft. (6.1 m), use larger pipe.

NOTE: Pipe-joint compounds that resist the action of LP gas

must be used. Do not use TEFLON_'*_ttape.

[] Must include shut-off valve

GAS SUPPLY CONNECTION REQUIREMENTS

[] Use an elbow and a 3/8" flare x 3/8" NPT adapter fitting

between the flexible gas connector and the dryer gas pipe,

as needed to avoid kinking.

[] Use only pipe-joint compound. Do not use TEFLON _t tape.

[] This dryer must be connected to the gas supply line with a

listed flexible gas connector that complies with the standard for

connectors for gas appliances, ANSi Z21.24 or CSA 6.10.

BURNER INPUT REQUIREMENTS

Elevations above 2,000 ft. (610 m):

[] When installed above 2,000 ft. (610 m) a 4% reduction of the

burner Btu rating shown on the model/serial number plate is

required for each 1,000 ft. (305 m) increase in elevation.

Gas supply pressure testing

[] The dryer must be disconnected from the gas supply piping

system during pressure testing at pressures greater than

1/2 psi.

DRYER GAS PiPE

[] The gas pipe that comes out through the rear of your dryer has

a 3/8" male pipe thread.

in the U.S.A.:

An individual manual shut-off valve must be installed within

six (6) ft. (1.8 m) of the dryer in accordance with the National

Fuel Gas Code, ANSi Z223.1. The location should be easy to

reach for opening and closing.

In Canada:

An individual manual shut-off valve must be installed in

accordance with the B149.1, Natural Gas and Propane

installation Code. It is recommended that an individual

manual shutoff valve be installed within six (6) ft. (1.8 m) of

the dryer. The location should be easy to reach for opening

and closing.

A !_

A. 3/8" flexible gas connector

B. 3/8" pipe to flare adapter fitting

C. 1/8" NPT minimum plugged tapping

D. 1/2" NPT gas supply line

E. Gas shutoff valve.

*5¾"

(146 ram}

1/2nn

(38 ram)

3/8" NPT dryer gas pipe

* NOTE: If the dryer is mounted on a pedestal, the gas

pipe height must be an additional 10" (254 mm) or

15.5" (394 mm) from the floor, depending on the pedestal

model. For a garage installation, the gas pipe height must

be an additional 18" (460 mm) from the floor.

1®TEFLON is a registered trademark of E.I. Dupont De Nemours and Company.

INSTALL LE¥_LING LEGS

Excessive Weight Hazard

Use two or more people to move and install dryer.

Failure to do so can result in back or other injury.

F1, Prepare dryer for leveling legs

m __ __

To avoid damaging floor, use a large flat piece of cardboard

from dryer carton; place under entire back edge of dryer.

Firmly grasp dryer body (not console panel) and gently lay

dryer down on cardboard.

_E GAS CONNECTION

(gas dryer models only)

"1, Connect gas supply to dryer

A. Flaredmale fitting

B. Non-flared malefitting

• • B

Remove red cap from gas pipe. Using a wrench to tighten,

connect gas supply to dryer. Use pipe-joint compound

on threads of all non-flared male fittings. Ifflexible metal

tubing is used, be sure there are no kinks.

NOTE: For LP gas connections, you must use pipe-joint

compound resistant to action of LP gas Do not use

TEFLON ®ttape.

It2, Plan pipe fitting connection (option i; "_

_ J

Examine leveling legs, find diamond marking. Screw legs into

leg holes by hand, use a wrench to finish turning legs until

diamond marking is no longer visible.

Place a carton corner post from dryer packaging under each

of the 2 dryer back corners. Stand the dryer up. Slide the

dryer on the corner posts until it is close to its final location.

Leave enough room to connect the exhaust vent.

A combination of pipe fittings must be used to connect dryer

to existing gas line. A recommended connection is shown.

Your connection may be different, according to supply line

type, size, and location.

3, Open shut=off valve

A. Closed valve

B.Open valve

Open shut-off valve in supply line; valve is open when handle

is parallel to gas pipe. Then, test all connections by brushing

on an approved noncorrosive leak-detection solution.

Bubbles will show a leak. Correct any leak found.

1®TEFLON is a registered trademark of E.I. Dupont De Nemours and Company.

Venting Requirements

Fire Hazard

Use a heavy metal vent.

Do not use a plastic vent.

Do not use a metal foil vent.

Failure to follow these instructions can result in death

or fire.

WARNING: To reduce the risk of fire, this dryer MUST BE

EXHAUSTED OUTDOORS.

IMPORTANT: Observe all governing codes and ordinances.

Dryer exhaust must not be connected into any gas vent,

chimney, wall, ceiling, attic, crawlspace, or a concealed space

of a building. Only rigid or flexible metal vent shall be used for

exhausting.

[]

(102 ram)

4" (102 ram) heavy metal exhaust vent

Only a 4" (102 mm) heavy metal exhaust vent and clamps

may be used.

Do not use plastic or metal foil vent.

Rigid metal vent:

[] Recommended for best drying performance and to avoid

crushing and kinking.

Flexible metal vent: (Acceptable only ifaccessible to clean)

[] Must be fully extended and supported in final dryer location.

[] Remove excess to avoid sagging and kinking that may result

in reduced airflow and poor performance.

[] Do not install in enclosed walls, ceilings, or floors.

[] The total length should not exceed 73/4ft. (2.4 m).

[] The length of flexible metal vent used must be included in

the overall vent system design as shown in the "Vent System

Chart".

NOTE: If using an existing vent system, clean lint from entire

length of the system and make sure exhaust hood is not

plugged with lint. Replace plastic or metal foil vents with rigid

metal or flexible metal vents. Review "Vent System Chart" and

if necessary, modify existing vent system to achieve best drying

performance.

Exhaust hoods:

[] An exhaust hood should cap the vent to keep rodents and

insects from entering the home.

[] Must be at least 12" (305 mm) from ground or any object

that may obstruct exhaust (such as flowers, rocks, bushes,

or snow).

[] Do not use an exhaust hood with a magnetic latch.

Recommended Styles:

Louvered Hood

Acceptable Style:

Angled Hood

Elbows:

Box Hood

[] 45° elbows provide better airflow than 90° elbows.

Clamps:

[] Use clamps to seal all joints.

[] Exhaust vent must not be connected or secured with screws

or other fastening devices that extend into interior of duct

and catch lint. Do not use duct ta }e.

improper venting can cause moisture and lint to collect

indoors, which may result in:

[] Moisture damage to woodwork, furniture, paint, wallpaper,

carpets, etc.

[] Housecleaning problems and health problems.

Plan Vent System

Choose your exhaust installation type

Recommended exhaust installation:

A. Dryer F. Rigid metal or

B Elbow flexible metal vent

C. Wall G. Vent length

D. Exhaust hood necessary to

E. Clamps connect elbows

H. Exhaust outlet

Fire Hazard

Cover unused exhaust holes with a manufacturer's

exhaust cover kit.

Contact your local dealer.

Failure to follow these instructions can result in death,

fire, electrical shock, or serious injury.

Optional exhaust installations:

This dryer can be converted to exhaust out the right side, left

side, or through the bottom. If you prefer, you may contact your

local dealer to have the dryer converted.

A B C

A. Standard rear offset exhaust installation

B. Left or right side exhaust installation

C. Bottom exhaust installation

Special provisions for mobile homes:

Exhaust vent must be securely fastened to a noncombustible

portion of mobile home and must not terminate beneath the

mobile home. Terminate exhaust vent outside.

Determine vent path:

[] Select route that will provide straightest and most direct

path outdoors.

[] Plan installation to use fewest number of elbows and turns.

[] When using elbows or making turns, allow as much room

as possible.

[] Bend vent gradually to avoid kinking.

[] Use as few 90° turns as possible.

Determine vent length and elbows needed for best

drying performance:

[] Use the following "Vent System Chart" to determine type

of vent material and hood combinations acceptable to use.

NOTE: Do not use vent runs longer than those specified

in "Vent System Chart".

Exhaust systems longer than those specified will:

[] Shorten life of dryer.

[] Reduce performance, resulting in longer drying times

and increased energy usage.

The "Vent System Chart" provides venting requirements

that will help achieve best drying performance.

Vent System Chart

Number of Type Box/Iouvered Angled

90° elbows of vent hoods hoods

Rigid metal 64 ft. (20 m) 58 ft. (17.7 m)

1 Rigid metal 54 ft. (16.5 m) 48 ft. (14.6 m)

1 J L

2 Rigidmetal 44 ft. (13.4m) 38 ft. (11.6m)

Rigid metal 35 ft. (10.7 m) 29 ft. (8.8 m)

Rigid metal 27 ft. (8.2 m) 21 ft. (6.4 m)

NOTE: Side and bottom exhaust installations have a 90° turn

inside the dryer. To determine maximum exhaust length, add

one 90° turn to the chart.

Install Vent System

. install exhaust hood

q 12" rnin.

"_--(305 mm)

Install exhaust hood and use caulking compound to seal

exterior wall opening around exhaust hood.

Connect vent to exhaust hood

iiii

iiiiiiiiiiiiiiiiiiiiiiiiii

!!!!!!!!!!!!!!!!!!!!!!!!!!

iiiiiiiiiiiiiiiiiiiiiiiiii

!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!

Vent must fit over the exhaust hood. Secure vent to exhaust

hood with 4" (102 mm) clamp. Run vent to dryer location using

straightest path possible. Avoid 90° turns. Use clamps to seal

all joints. Do not use duct tape, screws, or other fastening

devices that extend into interior of vent to secure vent,

because they can catch lint.

CONNECT INLET HOSE

The dryer must be connected to the cold water faucet using the

new inlet hoses. Do not use old hoses.

NOTE: Replace inlet hoses after 5 years of use to reduce the risk

of hose failure. Record hose installation or replacement dates on

the hoses for future reference.

Periodically inspect and replace hoses if bulges, kinks, cuts,

wear, or leaks are found.

1. Turn cold water off, remove hose,

and replace rubber washer

Turn cold water faucet off and remove washer inlet hose.

Check and see if rubber washer is in the "Y" connector.

Remove old rubber washer from inlet hose and replace with

new rubber washer provided.

If space permits, attach the female end of the "Y" connector

to the cold water faucet. See figure A.

If "Y" connector cannot be attached directly to the cold water

faucet, the short hose must be used. See figure B. Attach

short hose to cold water faucet. Screw on coupling by hand

until it is seated on faucet. Then attach "Y" connector to male

end of the short hose. Screw on coupling by hand until it is

seated on connector.

Using pliers, tighten the couplings with additional

two-thirds turn.

NOTE: Do not overtighten. Damage to the coupling

can result.

connector and tighten couplings

Remove protective cap from

water inlet valve. Attach other end

of long hose to fill valve at bottom of dryer

back panel. Screw on coupling by hand until it is seated on

fill valve connector. Using pliers, tighten the couplings an

additional two-thirds turn.

NOTE: Do not overtighten. Damage to the coupling

can result.

One end of the long hose has a wire mesh strainer inside the

coupling. Attach this end to the "Y" connector. Attach washer

cold inlet hose to other side of "Y" connector. Screw on

coupling by hand until it is seated on connector. Using pliers,

tighten the couplings an additional two-thirds turn.

NOTE: Do not overtighten. Damage to the coupling can result.

Check that the water faucets are turned on.

Check for leaks around "Y" connector, faucet, and hoses.

CONNECT _%NT

1, Connect vent to exhaust outlet

Using a 4" (102 mm) clamp, connect vent to exhaust outlet

in dryer. If connecting to existing vent, make sure vent is

clean. Dryer vent must fit over dryer exhaust outlet and inside

exhaust hood. Check that vent is secured to exhaust hood

with a 4" (102 mm) clamp.

2= Move dryer to final location

Move dryer to final location, taking care not to crush or

kink vent or flexible gas line.

After dryer is in place, remove corner posts and cardboard

from under dryer.

LE_L D R

1, Level dryer

Place

level here

Check levelness of dryer from

side to side. Repeat from front to back.

NOTE: The dryer must be level for the moisture sensing system

to operate correctly

Not Level LEVEL Not Level

2, Adjust leveling legs

If dryer is not level, prop up using a wood block, use wrench

to adjust legs up or down, and check again for levelness.

Once dryer is level, make sure all four legs are snug against

the floor and the dryer does not rock.

COMPLETE INSTALLATION

[_ Check that all parts are now installed. Ifthere is an extra

part, go back through steps to see what was skipped.

[_ Check that you have all of your tools.

[_ Dispose of/recycle all packaging materials.

[_ Be sure the water faucets are on.

[_ Check for leaks around "Y" connector, faucet, and hoses.

[_ Check dryer's final location. Be sure vent is not crushed

or kinked.

[_ Check that dryer is level. See "Level Dryer".

[_ Remove film on console and any tape remaining on dryer.

[_ Wipe dryer drum interior thoroughly with a damp cloth to

remove any dust.

[_ Read "Dryer Use" in your "Use and Care Guide".

[_ If you live in a hard water area, use of a water softener is

recommended to control the buildup of scale through the

water system in the dryer. Over time, the buildup of lime

scale may clog different parts of the water system, which will

reduce product performance. Excessive scale buildup may

lead to the need for certain part replacement or repair.

Electric Models

[_ Plug into a grounded outlet.

Gas Models

[_ Plug into a grounded outlet.

[_ Check that gas supply is on.

[_ Check for leaks.

[_ Check to be sure that the flexible gas line is not crushed

or kinked.

All Models:

[_ Select aTimed Dry heated cycle, and start dryer. Do not

select Air Only Temperature setting.

If dryer will not start, check the following:

• Start button has been pressed firmly.

• Dryer is plugged into an outlet and/or electrical supply is

connected.

• Household fuse is intact and tight, or circuit breaker has

not tripped.

• Dryer door is closed.

This dryer automatically runs an installation diagnostic routine

at the start of its first cycle.

NOTE: You may notice an odor when dryer is first heated. This

odor is common when heating element is first used. The odor will

go away.

DOOR RE %RS (OFTION )

The following instructions are for models with a round-shaped

door.

IMPORTANT: For models with a square shaped door, an

additional kit is needed. Please contact your retailer, or see the

"Assistance or Service" page in your "Use and Care Guide".

Tools needed:

Min. 8" long Torx®*T25

screwdriver

#2 Phillips screwdriver

iMPORTANT: If the protective film has not yet been

removed from the dryer, peel the film from the dryer

door before proceeding.

Using a Torx®*T25 screwdriver, remove the 4 screws securing

the door hinge to the dryer and lift up and out to remove the

door. Place the door on a soft towel or other non-scratch

surface. Reinstall the 4 screws in the holes.

1 ® TORX is a registered trademark of Saturn Fasteners, Inc.

2. Move the door strike

Using a Torx®t T25 screwdriver

remove the 2 screws securing

the door strike to the door frame of the dryer. Rotate the

strike 180 ° and attach to the opposite side of dryer door

frame, as shown.

_,!. Remove inner door from outer door

Position the door with the inside of the door facing up.

Using a Phillips screwdriver, remove the 10 screws securing

the inner door to the outer door. Lift off the inner door and

set aside.

Remove outer window assembly

from trim ring

Using a Phillips screwdriver, remove the 2 screws from the

outer window retainer and rotate the outer window assembly

clockwise until the square notches line up with the 4 tabs

on the trim ring indicated with arrows in the figure A above.

Then lift out the outer window and retainer up and off the trim

ring and set aside (B).

1 ® TORX is a registered trademark of Saturn Fasteners, Inc.

5, Reverse outer window assembly

Handle

Using a Phillips screwdriver, remove the 4 screws from the

outer window retainer and lift off the trim ring off the window

(A). Rotate trim ring 180° and secure with the 4 screws

removed earlier (B).

6, Rotate and reassemble outer window

assembly to trim ring

Bottom

' door

Notches

With the edge with 2 notches at the top, align the notches

on the outer window assembly with the tabs on the trim ring

and lower into place as shown in figure A. Rotate the outer

window assembly counterclockwise to lock tabs into place

(figure B). Using a Phillips screwdriver, secure with 2 screws

removed earlier.

IMPORTANT: Do not overtighten.

, Remove hinge and latch

1;' _' Latch

Hinge

Using a Torx®t T25 screwdriver, remove the 3 Torx screws

securing the latch plate and latch backing plate and the 5

screws holding the hinge assembly in place.

9. Reinstall inner door assembly

Bottom

of door

Position the door with the inside of the door facing up.

Reinstall the 10 screws securing the inner door to the

outer door.

Reinstall hinge and latch on

opposite sides

Using a Torx®t T25 screwdriver, reinstall the latch plate, latch

backing plate, and hinge assembly on the opposite sides from

which they were removed.

Using a Torx®1" T25 screwdriver, remove the 4 screws on the

dryer. Insert the tabs on the hinge into the mounting slot and

slide down to engage the top tab. Secure in place with

the 4 Torx®t T25 screws removed earlier.

1 ® TORX is a registered trademark of Saturn Fasteners, Inc.

SECURITE DE LA SECHEUSE

Votre sdcurit_ et celle des autres est trbs importante,

Nous donnons de nombreux messages de s_curit6 importants dans ce manuel et sur votre appareil m6nager. Assurez-vous de

toujours lire tousles messages de secufite et de vous y conformer.

Voici le symbole d'alerte de s_curit6.

Ce symbole d'alerte de s6curit6 vous signale les dangers potentiels de d6ces et de blessures graves &vous

et &d'autres.

Tous les messages de securit6 suivront le symbole d'alerte de securit6 et le mot "DANGER" ou

"AVERTISSEMENT". Ces roots signifient :

Risque possible de d_c_s ou de blessure grave si vous ne

suivez pas immddiatement les instructions.

Risque possible de d_ces ou de blessure grave si vous

ne suivez pas les instructions.

Tousles messages de s6curit6 vous diront quel est le danger potentiel et vous disent comment reduire le risque de blessure et

ce qui peut se produire en cas de non-respect des instructions.

T - "Risque d'incendie"

L'installation de la s_cheuse & linge doit _tre effectu_e par un installateur qualifi_,

Installer la s6cheuse conform_rnent aux instructions du fabricant et aux codes Iocaux,

Ne pas installer de s_cheuse & linge avec des mat_riaux d'_vacuation en plastique

souple ou un conduit m_tallique souple (de type papier d'aluminiurn), Si un conduit

rm_tallique souple est installS, celui-ci doit _tre d'un type sp_cifique identifi_ par le

fabricant de I'appareil et convenir & une utilisation avec les s_cheuses & linge. Les

rnat_riaux d'_vacuation souples sont connus pour s'affaisser, _tre facilement _cras_s

et bloquer la charpie, Ces situations obstrueront le d_bit d'air de la s_cheuse _ linge et

augrnenteront le risque d'incendie,

Pour r_duire le risque de blessure grave ou de d_c_s, suivre toutes

les instructions d'installation,

Conserver ces instructions.

AVERTISSEMENT : Pour votre securit6, les renseignements darts ce manuel doivent

_tre observes pour reduire au minimum les risques d'incendie ou d'e×plosion ou pour

eviter des dommages au produit, des blessures ou un deces.

- hie pas entreposer ou utiliser de I'essence ou d'autres vapeurs ou liquides

inflammables _ proximit_ de cet appareil ou de tout autre appareil _lectrom_nager.

QUE FAIRE DANS LE CAS D'UNE ODEUR DE GAZ :

= Ne pas tenter d'allumer un appareil.

o Ne pas toucher a un commutateur _lectrique; ne pas utiliser le t_lephone se trouvant

sur les lieux.

®I_vacuer tous les gens de la piece, de 1'6difice ou du quartier.

®Appeler immediatement le fournisseur de gaz d'un t_16phone voisin. Suivre ses

instructions.

= A defaut de joindre votre fournisseur de gaz, appeler les pompiers.

- L'installation et I'entretien doivent _tre effectu_s par un installateur qualifi_, une

agence de service ou le fournisseur de gaz.

AVERTISSEMENT : L'odorat ne permet pas toujours la detection d'une fuite de gaz.

Les distributeurs de gaz recommandent I'emploi d'un detecteur de gaz (homologation UL ou CSA).

Pour d'autre information, contacter le fournisseur de gaz local.

En cas de d6tection d'une fuite de gaz, ex6cuter les instructions "Que faire dans le cas d'une odeur de gaz".

IMPORTANT : L'installation du gaz doit se conformer aux codes Iocaux, ou en I'absence de codes Iocaux, au code canadien

d'installation B149.1 du gaz naturel ou du propane.

La s6cheuse doit _tre 61ectriquement reli6e & la terre conform6ment aux codes Iocaux, ou en I'absence de codes Iocaux, au Code

canadien de I'electricit6, CSA C22.1.

Dans I'Etat du Massachusetts, les instructionsd'installation suivantes sont applicables :

[] Les travaux d'installation et r6paration doivent 6tre ex6cut6s par un plombier ou tuyauteur qualifi6 ou licenci6, ou par le

personnel qualifie d'une entreprise licenci6e par I'E_tatdu Massachusetts.

[] Si une vanne 9,boisseau sph6rique est utilis6e, elle doit comporter une manette "T".

[] Si un conduit de raccordement flexible est utilis6, sa Iongueur ne doit pas d6passer 3 pi.

IMPORTANT : Pour mettre I'ancienne s6cheuse au rebut ou pour la remiser, enlever la porte.

La page est en cours de chargement...

Whirlpool YMED7000XW2 Guide d'installation

Marque: Whirlpool

Modèle: YMED7000XW2

Catégorie: Sèche-linge

Taper: Guide d'installation

Télécharger le PDF

rapport

dans d''autres langues

English: Whirlpool YMED7000XW2 Installation guide

Whirlpool YMED7000XW2 Guide d'installation

Whirlpool YMED7000XW2 Guide d'installation

dans d''autres langues

Documents connexes

Autres documents