Eazyzap FD496-A Manuel utilisateur

Catégorie
Tueurs d'insectes
Taper
Manuel utilisateur
Model:
FD496-A / FD497-A / FD498-A
Insect Killer
Instruction manual
2
EN Telephone Helpline: 1300225960
Safety Instructions
• A service agent/qualified technician should carry out
installation and any repairs if required. Do not remove any
components on this product.
• Consult Local and National Standards to comply with the
following:
- Health and Safety at Work Legislation
- Fire Precautions
- Wiring Regulations
- Building Regulations
• Always switch off and disconnect the power supply to the
appliance before cleaning.
• Install the appliance out of the reach of children.
• Never insert hands or other objects into the appliance while it
is connected to the power supply.
• Install the Insect killer at least 1 metre away from food
preparation areas.
• Never use near flammable objects.
• For INDOOR use only.
• Keep all packaging away from children.
• If the power cord is damaged, it must be replaced by an
EAZYZAP agent or a recommended qualified technician in
order to avoid a hazard.
EAZYZAP recommend that this appliance should be periodically
tested (at least annually) by a Competent Person. Testing
should include, but not be limited to: Visual Inspection,
Polarity Test, Earth Continuity, Insulation Continuity and
Functional Testing.
Danger - High voltage!
• The appliance emits UV radiation. Do not stare at the light.
3
EN
Telephone Helpline: 1300225960
The appliance is not to be
used in locations where
flammable vapour or explosive
dust is likely to exist.
• Do not use in barns, stables
and similar locations.
Product Description
FD496-A - LED Insect Killer - Small
FD497-A - LED Insect Killer - Medium
FD498-A - LED Insect Killer - Large
Introduction
Please take a few moments to carefully read
through this manual. Correct maintenance and
operation of this machine will provide the best
possible performance from your EAZYZAP product.
Pack Contents
The following is included:
Insect Killer
Instruction manual
Hanging chain
EAZYZAP prides itself on quality and service,
ensuring that at the time of packaging the contents
are supplied fully functional and free of damage.
Should you find any damage as a result of transit,
please contact your EAZYZAP dealer immediately.
Installation
Note: Ensure the mounting substrate and
the fixings used can support the weight of
the appliance. If in doubt seek professional
advice or assistance.
1. Remove all packaging and protective film from
the Insect killer.
2. For best results, locate the Insect killer in the
darkest part of the room, but at least 1 metre
away from food preparation areas.
Note: Close proximity to other light sources
such as sky lights and windows will reduce
the effectiveness of the Insect killer.
3. Connect the appliance to mains power.
Operation
WARNING: Under no
circumstances should hands be
placed anywhere near the high
voltage grid when the appliance
is operational.
The insect killer works by luring insects on to an
electrified metal grid using ultra-violet light. It
uses no chemicals and is pollution free. To use the
Insect killer:
1. Press the switch to the ON (I) position. Ensure
it is set to OFF (O) before plugging into mains.
2. The light will come on and the grid will become
electrically charged.
Cleaning, Care &
Maintenance
Always switch off the power
and disconnect the appliance
from the power supply before
cleaning.
Clean the collection tray regularly with warm
soapy water.
DO NOT immerse the appliance in water. Wipe
the safety guard and external casing with a
damp cloth.
Change the bulbs every 12 months.
4
EN Telephone Helpline: 1300225960
Changing the Bulb
WARNING: Always turn Off the appliance and disconnect from the power supply before
changing the bulb.
1. Remove the collection tray.
2. Lay the appliance face down.
3. Unscrew the two screws
holding the safety guard at
the rear of the Insect killer
[Fig. 1].
1
4. Lift up the guard rail [Fig. 2]. 2
5. Holding the ends of the bulb,
twist it ‘forwards’ in its socket
until it clicks [Fig. 3].
3
6. Slide the bulb up out of its
sockets [Fig. 4].
7. Replace with a new bulb.
8. Twist the new bulb
‘backwards’ to lock it back in
place.
9. Replace the guard rail and the
two screws.
4
Troubleshooting
A qualified technician must carry out repairs if required.
Fault Probable Cause Solution
The
appliance is
not working
The unit is not switched on Check the unit is plugged in correctly and
switched on
Plug or lead is damaged Replace plug or lead
Power supply Check power supply
Tube has expired Refer to the ‘Changing the Bulb’ section
Tube is faulty or has not been fitted correctly
5
EN
Telephone Helpline: 1300225960
Technical Specifications
Model Voltage Power Dimensions
h x w x d (mm) Weight
FD496-A 220-240V~ 50-60Hz 15W 272 x 350 x 86 2.05kg
FD497-A 220-240V~ 50-60Hz 19W 320 x 500 x 86 2.7kg
FD498-A 220-240V~ 50-60Hz 24W 320 x 650 x 86 3.4kg
Electrical Wiring
The plug is to be connected to a suitable mains socket.
This appliance is wired as follows:
Live wire (coloured brown) to terminal marked L
Neutral wire (coloured blue) to terminal marked N
Earth wire (coloured green/yellow) to terminal marked E
This appliance must be earthed.
If in doubt consult a qualified electrician.
Electrical isolation points must be kept clear of any obstructions. In the event of any emergency
disconnection being required they must be readily accessible.
Compliance
The product must not be disposed of as household waste. To help prevent possible harm to human
health and/or the environment, the product must be disposed of in an approved and environmentally safe
recycling process. For further information on how to dispose of this product correctly, contact the product
supplier, or the local authority responsible for waste disposal in your area.
EAZYZAP parts have undergone strict product testing in order to comply with
regulatory standards and specifications set by international, independent, and
federal authorities.
EAZYZAP products have been approved to carry the following symbol:
All rights reserved. No part of these instructions may be produced or transmitted in any form or by any means, electronic,
mechanical, photocopying, recording or otherwise, without the prior written permission of EAZYZAP.
Every effort is made to ensure all details are correct at the time of going to press, however, EAZYZAP reserve the right to
change specifications without notice.
DECLARATION OF CONFORMITY
Conformiteitsverklaring Déclaration de conformiKonformitätserklärung Dichiarazione di conformità
Declaración de conformidad Declaração de conformidade
Equipment Type Uitrustingstype • Type d'équipement Gerätetyp
Tipo di apparecchiatura Tipo de equipo Tipo de equipamento
Model Modèle Modell Modello
Modelo Malli
LED Insect Killer 15W
LED Insect Killer 19W
LED Insect Killer 24W
FD496 (-E & -A)
FD497 (-E & -A)
FD498 (-E & -A)
Application of Territory Legislation &
Council Directives(s)
Toepassing van Europese Richtlijn(en) •
Application de la/des directive(s) du
Conseil Anwendbare EU-Richtlinie(n)
Applicazione delle Direttive
• Aplicación de la(s) directiva(s) del
consejo Aplicação de directiva(s) do
Conselho
Low Voltage Directive (LVD) - 2014/35/EU
Electrical Equipment (Safety) Regulations 2016
EN 60335-1:2012 +A11:2014 +A13:2017
EN 60335-2-59:2003 +A1:2006 +A2:2009
+A11:2018
EN 62233:2008
Electro-Magnetic Compatibility (EMC) Directive
2014/30/EU - recast of 2004/108/EC
Electromagnetic Compatibility Regulations 2016
(S.I. 2016/1091)
EN55014-1:2017
EN55014-2:2015
EN 61000-3-2: 2014
EN 61000-3-3: 2013
Restriction of Hazardous Substances Directive
(RoHS) 2015/863 amending Annex II to Directive
2011/65/EU
Restriction of the Use of Certain Hazardous
Substances in Electrical and Electronic
Equipment Regulations 2012 (S.I. 2012/3032)
Electrical Safety
IEC 60335-1:2010 +A1:2013 +A2:2016
IEC 60335-2-59:2002 +A1:2006 +A2:2009
Electromagnetic Compatibility
EN55014-1:2017
EN55014-2:2015
EN 61000-3-2: 2014
EN 61000-3-3: 2013
Producer Name Naam fabrikant Nom du producteur Name des Herstellers
Nome del produttore Nombre del fabricante Nome do fabricante
Eazyzap
I, the undersigned, hereby declare that the equipment specified above conforms to the above Territory Legislation, Directive(s) and
Standard(s).
Ik, de ondergetekende, verklaar hierbij dat de hierboven gespecificeerde uitrusting goedgekeurd is volgens de bovenstaande Richtlijn(en) en
Standaard(en).
Je soussigné, confirme la conformité de l'équipement cité dans la présente à la / aux Directive(s) et Norme(s) ci-dessus
Ich, der/die Unterzeichnende, erkläre hiermit, dass das oben angegebene Gerät der/den oben angeführten Richtlinie(n) und Norm(en) entspricht.
Il sottoscritto dichiara che l'apparecchiatura di sopra specificata è conforme alle Direttive e agli Standard sopra riportati.
El abajo firmante declara por la presente que el equipo arriba especificado está en conformidad con la(s) directiva(s) y estándar(es) arriba
mencionadas.
Eu, o abaixo-assinado, declaro que o equipamento anteriormente especificado está em conformidade com a(s) anterior(es) Directiva(s) e
Norma(s)
Date • Data • Date • Datum • Data •
Fecha • Data
28th April 2021
Signature Handtekening
Signature • Unterschrift Firma •
Firma • Assinatura
Full Name Volledige naam • Nom
et prénom Vollständiger Name •
Nome completo Nombre completo
Nome por extenso
Josie Holt
Position Functie Fonction
Position • Qualifica Posición
Função
Manager
Manager/ Importer
Commercial Manager/ Responsible
Supplier
Producer Address Adres fabrikant
Adresse du producteur Anschrift
des Herstellers Indirizzo del
produttore Dirección del fabricante
• Morada do fabricante
Avonmouth,
Bristol,
BS11 8TB
Blarney Business Park
Blarney
Co. Cork, Ireland
15 Bagdally Road,
Campbelltown
NSW 2560
DocuSign Envelope ID: 82CF60EC-07ED-4BB9-9B0D-D025707A0398
FD496-A-FD497-A-FD498-A_A5_v2_2022/07/05
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Eazyzap FD496-A Manuel utilisateur

Catégorie
Tueurs d'insectes
Taper
Manuel utilisateur

dans d''autres langues