Hikoki DH1826DA Manuel utilisateur

Model

Modèle

Modelo DH 1826DA

Cordless Rotary Hammer

Marteau rotatif sans ﬁ l

Martillo perforador inalámbrico

SAFETY INSTRUCTIONS AND INSTRUCTION MANUAL

WARNING

IMPROPER OR UNSAFE use of this power tool can result in death or serious bodily injury!

This manual contains important information about product safety. Please read and

understand this manual BEFORE operating the power tool. Please keep this manual

available for other users and owners before they use the power tool. This manual should be

stored in safe place.

INSTRUCTIONS DE SECURITE ET MODE D’EMPLOI

AVERTISSEMENT

Une utilisation INCORRECTE OU DANGEREUSE de cet outil motorisé peut entraîner la

mort ou de sérieuses blessures corporelles !

Ce mode d’emploi contient d’importantes informations à propos de la sécurité de ce produit.

Prière de lire et de comprendre ce mode d’emploi AVANT d’utiliser l’outil motorisé. Garder ce

mode d’emploi à la disponibilité des autres utilisateurs et propriétaires avant qu’ils utilisent

l’outil motorisé. Ce mode d’emploi doit être conservé dans un endroit sûr.

INSTRUCCIONES DE SEGURIDAD Y MANUAL DE INSTRUCCIONES

ADVERTENCIA

¡La utilización INAPROPIADA O PELIGROSA de esta herramienta eléctrica puede resultar

en lesiones de gravedad o la muerte!

Este manual contiene información importante sobre la seguridad del producto. Lea y

comprenda este manual ANTES de utilizar la herramienta eléctrica. Guarde este manual

para que puedan leerlo otras personas antes de utilizar la herramienta eléctrica. Este

manual debe ser guardado en un lugar seguro.

Designed for operating in USA & Canada only.

When this product is used in areas other than the USA & Canada,

we cannot guarantee the product quality and performance.

2

English

IMPORTANT SAFETY INSTRUCTIONS

Read all of the safety precautions, warnings and operating instructions in the Instruction Manual before operating or

maintaining this power tool.

Most accidents that result from power tool operation and maintenance are caused by the failure to observe basic safety

rules or precautions. An accident can often be avoided by recognizing a potentially hazardous situation before it occurs,

and by observing appropriate safety procedures.

Basic safety precautions are outlined in the "SAFETY" section of this Instruction Manual and in the sections which

contain the operation and maintenance instructions.

Hazards that must be avoided to prevent bodily injury or machine damage are identiﬁ ed by WARNINGS on the power

tool and in this Instruction Manual.

NEVER use this power tool in a manner that has not been speciﬁ cally recommended by metabo HPT.

MEANINGS OF SIGNAL WORDS

WARNING indicates a potentially hazardous situations which, if ignored, could result in death or serious injury.

CAUTION indicates a potentially hazardous situations which, if not avoided, may result in minor or moderate injury, or

may cause machine damage.

NOTE emphasizes essential information.

SAFETY

GENERAL POWER TOOL SAFETY WARNINGS

WARNING

Read all safety warnings and all instructions.

Failure to follow the warnings and instructions may result in electric shock, ﬁ re and/or serious injury.

Save all warnings and instructions for future reference.

The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated

(cordless) power tool.

1) Work area safety

a) Keep work area clean and well lit.

Cluttered or dark areas invite accidents.

b) Do not operate power tools in explosive

atmospheres, such as in the presence of

ﬂ ammable liquids, gases or dust.

Power tools create sparks which may ignite the

dust or fumes.

c) Keep children and bystanders away while

operating a power tool.

Distractions can cause you to lose control.

2) Electrical safety

a) Power tool plugs must match the outlet.

Never modify the plug in any way.

Do not use any adapter plugs with earthed

(grounded) power tools.

Unmodiﬁ ed plugs and matching outlets will reduce

risk of electric shock.

b) Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and

refrigerators.

There is an increased risk of electric shock if your

body is earthed or grounded.

c) Do not expose power tools to rain or wet

conditions.

Water entering a power tool will increase the risk

of electric shock.

d) Do not abuse the cord. Never use the cord

for carrying, pulling or unplugging the power

tool.

Keep cord away from heat, oil, sharp edges or

moving parts.

Damaged or entangled cords increase the risk of

electric shock.

e) When operating a power tool outdoors, use

an extension cord suitable for outdoor use.

Use of a cord suitable for outdoor use reduces the

risk of electric shock.

f) If operating a power tool in a damp location

is unavoidable, use a residual current device

(RCD) protected supply.

Use of an RCD reduces the risk of electric shock.

3

English

3) Personal safety

a) Stay alert, watch what you are doing and use

common sense when operating a power tool.

Do not use a power tool while you are tired

or under the inﬂ uence of drugs, alcohol or

medication.

A moment of inattention while operating power

tools may result in serious personal injury.

b) Use personal protective equipment. Always

wear eye protection.

Protective equipment such as dust mask, non-skid

safety shoes, hard hat, or hearing protection used

for appropriate conditions will reduce personal

injuries.

c) Prevent unintentional starting. Ensure the

switch is in the oﬀ -position before connecting

to power source and/or battery pack, picking

up or carrying the tool.

Carrying power tools with your ﬁ nger on the switch

or energising power tools that have the switch on

invites accidents.

d) Remove any adjusting key or wrench before

turning the power tool on.

A wrench or a key left attached to a rotating part of

the power tool may result in personal injury.

e) Do not overreach. Keep proper footing and

balance at all times.

This enables better control of the power tool in

unexpected situations.

f) Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing and gloves

away from moving parts.

Loose clothes, jewellery or long hair can be caught

in moving parts.

g) If devices are provided for the connection

of dust extraction and collection facilities,

ensure these are connected and properly

used.

Use of dust collection can reduce dust-related

hazards.

4) Power tool use and care

a) Do not force the power tool. Use the correct

power tool for your application.

The correct power tool will do the job better and

safer at the rate for which it was designed.

b) Do not use the power tool if the switch does

not turn it on and oﬀ .

Any power tool that cannot be controlled with the

switch is dangerous and must be repaired.

c) Disconnect the plug from the power source

and/or the battery pack from the power tool

before making any adjustments, changing

accessories, or storing power tools.

Such preventive safety measures reduce the risk

of starting the power tool accidentally.

d) Store idle power tools out of the reach of

children and do not allow persons unfamiliar

with the power tool or these instructions to

operate the power tool.

Power tools are dangerous in the hands of

untrained users.

e) Maintain power tools. Check for misalignment

or binding of moving parts, breakage of parts

and any other condition that may aﬀ ect the

power tool’s operation.

If damaged, have the power tool repaired

before use.

Many accidents are caused by poorly maintained

power tools.

f) Keep cutting tools sharp and clean.

Properly maintained cutting tools with sharp

cutting edges are less likely to bind and are easier

to control.

g) Use the power tool, accessories and tool bits

etc. in accordance with these instructions,

taking into account the working conditions

and the work to be performed.

Use of the power tool for operations diﬀ erent

from those intended could result in a hazardous

situation.

5) Battery tool use and care

a) Recharge only with the charger speciﬁ ed by

the manufacturer.

A charger that is suitable for one type of battery

pack may create a risk of ﬁ re when used with

another battery pack.

b) Use power tools only with speciﬁ cally

designated battery packs.

Use of any other battery packs may create a risk of

injury and ﬁ re.

c) When battery pack is not in use, keep it away

from other metal objects like paper clips,

coins, keys, nails, screws, or other small

metal objects, that can make a connection

from one terminal to another.

Shorting the battery terminals together may cause

burns or a ﬁ re.

d) Under abusive conditions, liquid may be

ejected from the battery; avoid contact. If

contact accidentally occurs, ﬂ ush with water.

If liquid contacts eyes, additionally seek

medical help.

Liquid ejected from the battery may cause irritation

or burns.

6) Service

a) Have your power tool serviced by a

qualiﬁ ed repair person using only identical

replacement parts.

This will ensure that the safety of the power tool is

maintained.

4

English

– WARNING –

To reduce the risk of injury, user must read

instruction manual.

SPECIFIC SAFETY RULES AND SYMBOLS

1. Wear ear protectors.

Exposure to noise can cause hearing

loss.

2. Use auxiliary handle(s), if supplied with the tool.

Loss of control can cause personal injury.

3. Hold power tools by insulated gripping surfaces

when performing an operation where the cutting

accessory may contact hidden wiring.

Cutting accessory contacting a “live” wire may make

exposed metal parts of the power tool “live” and could

give the operator an electric shock.

4. NEVER touch the tool bit with bare hands after

operation.

5. NEVER wear gloves made from materials likely to roll

up such as cotton, wool, cloth or string, etc.

6. ALWAYS attach the side handle and securely grip the

Rotary Hammer.

7. Never touch moving parts.

NEVER place your hands, ﬁ ngers or other body parts

near the tool’s moving parts.

8. Never operate without all guards in place.

NEVER operate this tool without all guards or safety

features in place and in proper working order. If

maintenance or servicing requires the removal of a

guard or safety feature, be sure to replace the guard

or safety feature before resuming operation of the

tool.

9. Use right tool.

Don’t force small tool or attachment to do the job of a

heavy-duty tool.

Don’t use tool for purpose not intended —for

example— don’t use circular saw for cutting tree

limbs or logs.

10. Never use a power tool for applications other

than those speciﬁ ed.

NEVER use a power tool for applications other than

those speciﬁ ed in the Instruction Manual.

11. Handle tool correctly.

Operate the tool according to the instructions

provided herein. Do not drop or throw the tool.

NEVER allow the tool to be operated by children,

individuals unfamiliar with its operation or

unauthorized personnel.

12. Keep all screws, bolts and covers tightly in place.

Keep all screws, bolts, and plates tightly mounted.

Check their condition periodically.

13. Do not use power tools if the plastic housing or

handle is cracked.

Cracks in the tool’s housing or handle can lead to

electric shock. Such tools should not be used until

repaired.

14. Bits and accessories must be securely mounted

to the tool.

Prevent potential injuries to yourself or others. Bits

and accessories which have been mounted to the tool

should be secure and tight.

15. Keep motor air vent clean.

The tool’s motor air vent must be kept clean so that

air can freely ﬂ ow at all times. Check for dust build-up

frequently.

16. Because the cordless tool operates by battery power,

be aware of the fact that it can begin to operate at any

time.

17. NEVER use a tool which is defective or operating

abnormally.

If the tool appears to be operating unusually, making

strange noises, or otherwise appears defective, stop

using it immediately and arrange for repairs by a

metabo HPT authorized service center.

18. NEVER leave tool running unattended. Turn power

oﬀ .

Don’t leave tool until it comes to a complete stop.

19. Carefully handle power tools.

Should a power tool be dropped or struck against

hard materials inadvertently, it may be deformed,

cracked, or damaged.

20. Do not wipe plastic parts with solvent.

Solvents such as gasoline, thinner benzine, carbon

tetrachloride, and alcohol may damage and crack

plastic parts. Do not wipe them with such solvents.

Wipe plastic parts with a soft cloth lightly dampened

with soapy water and dry thoroughly.

21. ALWAYS wear eye protection that meets the

requirement of the latest revision of

ANSI Standard Z87.1.

22. Do not use the product if the tool or the battery

terminals (battery mount) are deformed.

Installing the battery could cause a short circuit that

could result in smoke emission or ignition.

23. Keep the tool’s terminals (battery mount) free of swarf

and dust.

○

Prior to use, make sure that swarf and dust have not

collected in the area of the terminals.

○

During use, try to avoid swarf or dust on the tool from

falling on the battery.

○

When suspending operation or after use, do not leave

the tool in an area where it may be exposed to falling

swarf or dust.

5

English

Doing so could cause a short circuit that could result

in smoke emission or ignition.

24. ALWAYS be careful with buried object such as an

underground wiring.

Touching live wiring or electric cable with this tool may

result in electric shock.

Conﬁ rm before use whether hidden objects are

present, such as electric cables within the wall, ﬂ oor

or ceiling.

25. Deﬁ nitions for symbols used on this tool

V .............volts

—

--- ........... direct current

no ...........no load speed

---/min .....revolutions per minute

IMPORTANT SAFETY INSTRUCTIONS

FOR BATTERY CHARGER

WARNING

Death or serious bodily injury could result from

improper or unsafe use of battery chargers.

To avoid these risks, follow these basic safety

instructions:

Table 1

RECOMMENDED MINIMUM AWG SIZE FOR

EXTENSION CORDS FOR BATTERY CHARGERS

AC Input Rating Amperes* AWG Size of Cord

Equal to or

greater than but less

than

Length of Cord, Feet (Meter)

25 (7.5) 50 (15) 100 (30) 150 (45)

0 2 18 18 18 16

2 3 18 18 16 14

3 4 18 18 16 14

READ ALL INSTRUCTIONS

1. This manual contains important safety and operating

instructions for battery charger Model UC18YSL3.

2. Before using battery charger, read all instructions

and cautionary markings on (1) battery charger, (2)

battery, and (3) product using battery.

3. To reduce risk of injury, charge metabo HPT

rechargeable battery type BSL36A18 and BSL18

series. Other type of batteries may burst causing

personal injury and damage.

4. Use of an attachment not recommended or sold by

the battery charger manufacturer may result in a risk

of ﬁ re, electric shock, or injury to persons.

5. To reduce risk of damage to electric plug and cord,

pull by plug when disconnecting battery charger.

6. Make sure cord is located so that it will not be stepped

on, tripped over, or otherwise subjected to damage or

stress.

7. An extension cord should not be used unless

absolutely necessary. Use of improper extension

cord could result in a risk of ﬁ re and electric shock.

If extension cord must be used make sure:

a. That blades of extension cord are the same

number, size, and shape as those of plug on

battery charger:

b. That extension cord is properly wired and in good

electrical condition; and

c. That wire size is large enough for AC ampere

rating of battery charger as speciﬁ ed in Table 1.

* If the input rating of a battery charger is given in watts

rather than in amperes, the corresponding ampere

rating is to be determined by dividing the wattage

rating by the voltage rating–for example:

1,250 watts = 10 amperes

125 volts

8. Do not operate battery charger with damaged cord or

plug-replace them immediately.

9. Do not operate battery charger if it has received a

sharp blow, been dropped, or otherwise damaged in

any way; take it to a qualiﬁ ed serviceman.

10. Do not disassemble battery charger; take it to a

qualiﬁ ed serviceman when service or repair is

required. Incorrect reassembly may result in a risk of

electric shock or ﬁ re.

11. To reduce risk of electric shock, unplug charger from

receptacle before attempting any maintenance or

cleaning. Removing the battery will not reduce this

risk.

6

English

IMPORTANT SAFETY INSTRUCTIONS

FOR USE OF THE BATTERY AND

BATTERY CHARGER

You must charge the battery before you can use the power

tool. Before using the model UC18YSL3 battery charger,

be sure to read all instructions and cautionary statements

on it, the battery and in this manual.

REMEMBER: USE ONLY metabo HPT BATTERY TYPE

BSL36A18. OTHER TYPES OF BATTERIES MAY BURST

AND CAUSE INJURY!

Follow these instructions to avoid the risk of injury:

WARNING

Improper use of the battery or battery charger

can lead to serious injury. To avoid these injuries:

1. NEVER disassemble the battery.

2. NEVER incinerate the battery, even if it is damaged or

is completely worn out. The battery can explode in a

ﬁ re.

3. NEVER short-circuit the battery.

4. NEVER insert any objects into the battery charger’s

air vents. Electric shock or damage to the battery

charger may result.

5. NEVER charge outdoors. Keep the battery away

from direct sunlight and use only where there is low

humidity and good ventilation.

6. NEVER charge when the temperature is below 14°F

(-10°C) or above 104°F (40°C).

7. NEVER connect two battery chargers together.

8. NEVER insert foreign objects into the hole for the

battery or the battery charger.

9. NEVER use a booster transformer when charging.

10. NEVER use DC power to charge.

11. NEVER store the battery or battery charger in places

where the temperature may reach or exceed 104°F

(40°C) such as inside metal box or car.

12. NEVER expose the battery or battery charger to rain

or wet conditions.

13. ALWAYS operate charger on standard household

electrical power (120 volts). Using the charger on any

other voltage may overheat and damage the charger.

14. ALWAYS wait at least 15 minutes between charges to

avoid overheating the charger.

15. ALWAYS disconnect the power cord from its

receptacle when the charger is not in use.

CAUTION ON LITHIUM-ION BATTERY

To extend the lifetime, the lithium-ion battery equips with

the protection function to stop the output.

In the cases of 1 to 3 described below, when using this

product, even if you are pulling the switch, the motor may

stop. This is not the trouble but the result of protection

function.

1. When the battery power remaining runs out, the motor

stops.

In such case, charge it up immediately.

2. If the tool is overloaded, the motor may stop. In this

case, release the switch of tool and eliminate causes

of overloading. After that, you can use it again.

3. If the battery is overheated under overload work, the

battery power may stop.

In this case, stop using the battery and let the battery

cool. After that, you can use it again.

Furthermore, please heed the following warning and

caution.

WARNING

In order to prevent any battery leakage, heat

generation, smoke emission, explosion and ignition

beforehand, please be sure to heed the following

precautions.

1. Make sure that swarf and dust do not collect on the

battery.

○

During work make sure that swarf and dust do not fall

on the battery.

○

Make sure that any swarf and dust falling on the power

tool during work do not collect on the battery.

○

Do not store an unused battery in a location exposed

to swarf and dust.

○

Before storing a battery, remove any swarf and dust

that may adhere to it and do not store it together with

metal parts (screws, nails, etc.).

2. Do not pierce battery with a sharp object such as a

nail, strike with a hammer, step on, throw or subject

the battery to severe physical shock.

3. Do not use an apparently damaged or deformed

battery.

4. Do not use the battery for a purpose other than those

speciﬁ ed.

5. If the battery charging fails to complete even when a

speciﬁ ed recharging time has elapsed, immediately

stop further recharging.

6. Do not put or subject the battery to high temperatures

or high pressure such as into a microwave oven,

dryer, or high pressure container.

7. Keep away from ﬁ re immediately when leakage or foul

odor are detected.

8. Do not use in a location where strong static electricity

generates.

7

English

9. If there is battery leakage, foul odor, heat generated,

discolored or deformed, or in any way appears

abnormal during use, recharging or storage,

immediately remove it from the equipment or battery

charger, and stop use.

10. Do not immerse the battery or allow any ﬂ uids to ﬂ ow

inside. Conductive liquid ingress, such as water, can

cause damage resulting in ﬁ re or explosion. Store your

battery in a cool, dry place, away from combustible

and ﬂ ammable items. Corrosive gas atmospheres

must be avoided.

CAUTION

1. If liquid leaking from the battery gets into your eyes,

do not rub your eyes and wash them well with fresh

clean water such as tap water and contact a doctor

immediately.

If left untreated, the liquid may cause eye-problems.

2. If liquid leaks onto your skin or clothes, wash well with

clean water such as tap water immediately.

There is a possibility that this can cause skin irritation.

3. If you ﬁ nd rust, foul odor, overheating, discolor,

deformation, and/or other irregularities when using

the battery for the ﬁ rst time, do not use and return it to

your supplier or vendor.

WARNING

If an electrically conductive foreign object enters the

terminals of the lithium ion battery, a short-circuit may

occur resulting in the risk of ﬁ re. Please observe the

following matters when storing the battery.

○

Do not place electrically conductive cuttings,

nails, steel wire, copper wire or other wire in the

storage case.

○

Either install the battery in the power tool or store

by securely pressing into the battery cover until

the ventilation holes are concealed to prevent

short-circuits (See Fig. 3).

REGARDING LITHIUM-ION BATTERY

TRANSPORTATION

When transporting a lithium-ion battery, please observe

the following precautions.

WARNING

Notify the transporting company that a package

contains a lithium-ion battery, inform the company

of its power output and follow the instructions of the

transportation company when arranging transport.

●

Lithium-ion batteries that exceed a power output

of 100 Wh are considered to be in the freight

classiﬁ cation of Dangerous Goods and will

require special application procedures.

●

For transportation abroad, you must comply with

international law and the rules and regulations of

the destination country.

●

If the BSL36B18 is installed in the power tool, the

power output will exceed 100 Wh and the unit will

be classiﬁ ed as Dangerous Goods for freight

classiﬁ cation.

Wh

Power Output

2 to 3 digit number

Fig. 1

SAVE THESE INSTRUCTIONS

AND

MAKE THEM AVAILABLE TO OTHER USERS

AND

OWNERS OF THIS TOOL!

8

English

FUNCTIONAL DESCRIPTION

NOTE

The information contained in this Instruction Manual is designed to assist you in the safe operation and maintenance

of the power tool.

NEVER operate, or attempt any maintenance on the tool unless you have ﬁ rst read and understood all safety

instructions contained in this manual.

Some illustrations in this Instruction Manual may show details or attachments that diﬀ er from those on your own

power tool.

NAME OF PARTS

1. Cordless Rotary Hammer (DH1826DA)

Grip

Change lever Pushing

button

Switch

trigger

Front cap

Drill bit

Side handle

LED Light Battery

Handle

Display

panel

Changeover

switch Auto stop

lamp

Display

lamp

Name plate

Motor

Gear cover

Depth gauge

Housing

Indicator lamp

Fig. 2

2. Battery (BSL36A18) 3. Battery Charger (UC18YSL3)

Latch

Ventilation holes

Terminals

Battery cover

Battery Body Guide rail

Nameplate

Charge

indicator lamp

Ventilation

holes

Cord

Fig. 3 Fig. 4

9

English

SPECIFICATIONS

1. Cordless Rotary Hammer

Model DH1826DA

Voltage 18 V

No- Load speed 0–950 /min

Full- Load impact rate 0–4,300 /min

Capacity Drilling

Concrete 1-1/32" (26 mm)

Steel 1/2" (13 mm)

Wood 1-1/16" (27 mm)

Type of motor Fan-cooled DC brushless motor

Battery* Type* Li-ion battery Model BSL36A18

Voltage DC 36 V / 18 V

Weight 8.4 lbs. (3.8 kg) (BSL36A18 attached)

* Existing batteries (BSL3660/3626/3620 and BSL14xx series, etc.) cannot be used with this tool.

2. Battery Charger

Model UC18YSL3

Input power source Single phase: AC 120 V 60 Hz

Charging time

(At a temperature of 68°F (20°C)) BSL36A18 : Approx. 32 min

Charging voltage DC 14.4 V–18 V

Charging current DC 8.0 A

Weight 1.3 lbs. (0.6 kg)

10

English

ASSEMBLY AND OPERATION

CHARGING METHOD

NOTE

Before plugging into the receptacle, make sure the

following points.

○

The power source voltage is stated on the

nameplate.

○

The cord is not damaged.

WARNING

Do not charge at voltage higher than indicated

on the nameplate.

If charged at voltage higher than indicated on

the nameplate, the charger will burn up.

1. Connect the charger’s power cord to a receptacle.

When the power cord is connected, the charge

indicator lamp will blink in red. (At 1-second intervals)

WARNING

Do not use the electrical cord

if damaged. Have it repaired

immediately.

2. Insert the battery to the battery charger.

Insert the battery into the battery charger as shown in

Fig. 7.

Battery

Charge

indicator lamp

Guide rail

Fig. 7

3. Charging

When inserting a battery in the charger, the charge

indicator lamp will blink in blue.

When the battery becomes fully recharged, the

charge indicator lamp will light up in green. (See

Table 2)

(1) Charge indicator lamp indication

The indications of the charge indicator lamp will be

as shown in Table 2, according to the condition of the

battery charger or the battery.

APPLICATIONS

Rotation and hammering function

○

Drilling anchor holes

○

Drilling holes in concrete

○

Drilling holes in tile

Rotation only function

○

Drilling in steel or wood (with optional accessories)

○

Tightening machine screws, wood screws

(with optional accessories)

Hammering only function

○

Light-duty chiselling of concrete, groove digging and

edging.

REMOVAL AND INSTALLATION METHOD

OF BATTERY

1. Battery removal

Hold the handle tightly and push the battery latch to

remove the battery (See Fig. 5).

CAUTION

Never short-circuit the battery.

2. Battery installation

Insert the battery while observing its polarities (see

Fig. 6).

Battery

Pull out

Push

Latch

Fig. 5

Insert

Fig. 6

11

English

Table 2

Indications of the charge indicator lamp

Charge

indicator

lamp

(RED /

BLUE /

GREEN /

PURPLE)

Before

charging Blinks

(RED)

Lights for 0.5 seconds. Does not light

for 0.5 seconds.

(oﬀ for 0.5 seconds) Plugged into power source

While

charging

Blinks

(BLUE)

Lights for 0.5 seconds. Does not light

for 1 second.

(oﬀ for 1 second) Battery capacity at less than

50%

Blinks

(BLUE)

Lights for 1 second. Does not light for

0.5 seconds.

(oﬀ for 0.5 seconds) Battery capacity at less than

80%

Lights

(BLUE) Lights continuously Battery capacity at more than

80%

Charging

complete Lights

(GREEN)

Lights continuously

(Continuous buzzer sound: about

6 seconds)

Overheat

standby Blinks

(RED)

Lights for 0.3 seconds. Does not light

for 0.3 seconds.

(oﬀ for 0.3 seconds)

Battery overheated. Unable

to charge. (Charging will

commence when battery cools)

Charging

impossible Flickers

(PURPLE)

Lights for 0.1 seconds. Does not light

for 0.1 seconds.

(oﬀ for 0.1 seconds)

(Intermittent buzzer sound: about

2 seconds)

Malfunction in the battery or the

charger

NOTE

The recharging time may vary according to the

ambient temperature.

4. Disconnect battery charger from the receptacle.

CAUTION

Do not pull the plug out of the receptacle by

pulling on the cord.

Make sure to grasp the plug when removing from

receptacle to avoid damaging cord.

5. Remove the battery from the battery charger.

Supporting the battery charger with hand, pull out the

battery from the battery charger.

NOTE

Be sure to pull out the battery from the battery charger

after use, and then keep it.

(2) Regarding the temperature of the rechargeable

battery.

The temperatures for rechargeable batteries are

as shown in the Table 3, and batteries that have

become hot should be cooled for a while before being

recharged.

Table 3

Rechargeable

batteries Temperatures at which the battery

can be recharged

BSL36A18 32°F–122°F

(0°C–50°C)

(3) Regarding recharging time (At 68°F (20°C))

Table 4 Charging time

Charger

Battery UC18YSL3

BSL36A18 Approx. 32 min

12

English

Regarding electric discharge in case of new

batteries, etc.

As the internal chemical substance of new batteries

and batteries that have not been used for an extended

period is not activated, the electric discharge might

be low when using them the ﬁ rst and second time.

This is a temporary phenomenon, and normal time

required for recharging will be restored by recharging

the batteries 2–3 times.

How to make the batteries perform longer

(1) Recharge the batteries before they become

completely exhausted.

When you feel that the power of the tool becomes

weaker, stop using the tool and recharge its battery.

If you continue to use the tool and exhaust the electric

current, the battery may be damaged and its life will

become shorter.

(2) Avoid recharging at high temperatures.

A rechargeable battery will be hot immediately after

use. If such a battery is recharged immediately after

use, its internal chemical substance will deteriorate,

and the battery life will be shortened. Leave the

battery and recharge it after it has cooled for a while.

CAUTION

●

When the battery charger has been continuosly

used, the battery charger will be heated, thus

constituting the cause of the failures. Once the

charging has been completed, give 15 minutes

rest until the next charging.

●

If the battery is charged while it is heated because

it has been left for a long time in a location

subject to direct sunlight or because the battery

has just been used, the charge indicator lamp of

UC18YSL3 charger lights for 0.3 seconds, does

not light for 0.3 seconds (oﬀ for 0.3 seconds). In

such a case, ﬁ rst let the battery cool, then start

charging.

●

When the charge indicator lamp ﬂ ickers (at

0.2–second intervals), check for and take out

any foreign objects in the charger’s battery

installation hole. If there are no foreign objects,

it is probable that the battery or charger is

malfunctioning. Take it to your authorized

Service Center.

HOW TO RECHARGE USB DEVICE

When an unexpected problem occurs, the data in a USB

device connected to this product may be corrupted or lost.

Always make sure to back up any data contained in the

USB device prior to use with this product.

Please be aware that our company accepts absolutely no

responsibility for any data stored in a USB device that is

corrupted or lost, nor for any damage that may occur to a

connected device.

WARNING

○

Prior to use, check the connecting USB cable for

any defect or damage.

Using a defective or damaged USB cable can

cause smoke emission or ignition.

○

When the product is not being used, cover the

USB port with the rubber cover.

Buildup of dust etc. in the USB port can cause

smoke emission or ignition.

NOTE

○

The time required for charging will be longer when

a USB device and battery are being simultaneously

charged.

○

There may be an occasional pause during USB

recharging.

○

When a USB device is not being charged, turn the

USB power switch OFF and remove the USB device

from the charger.

Failure to do so may not only reduce the battery life

of a USB device, but may also result in unexpected

accidents.

(1) Select a charging method

Depending on the charge method selected, either the

battery is inserted into the charger or the power cord

is plugged into an outlet.

○

Charging a USB device by battery (Fig. 8-a)

○

Charging a USB device from a electrical outlet

(Fig. 8-b)

○

Charging a USB device and battery from a

electrical outlet (Fig. 8-c)

abc

Fig. 8

13

English

(2) Turn the USB power switch ON (Fig. 9)

When you turn the USB power switch ON, the USB

power indicator lamp will light up.

USB power switch

USB power

indicator lamp

Rubber cover

USB port

USB cable

Fig. 9

(3) Connect the USB cable. (Fig. 9)

Pull back the rubber cover and ﬁ rmly plug in a

commercially available USB cable (appropriate to the

device being charged) into the USB port.

○

When the power cord is not plugged into an outlet and

the battery runs out of power, power output will stop

and the USB power indicator lamp will shut oﬀ .

○

When the USB power indicator lamp goes out, change

the battery or plug the power cord into an electrical

outlet.

(4) When charging is completed

○

The USB power indicator lamp will not go out when a

USB device has been completely charged.

To verify charge status, check the USB device.

○

Turn the USB power switch OFF and unplug the power

cord from the electrical outlet. (Fig. 9)

○

Remove the battery from the charger and place the

rubber cover over the USB port.

BEFORE USE

Check the work area to make sure that it is clear of debris

and clutter.

Clear the area of unnecessary personnel. Ensure that

lighting and ventilation is adequate.

PRIOR TO OPERATION

1. Conﬁ rming condition of the environment

Conﬁ rm that the work site is placed under appropriate

conditions conforming to prescribed precautions.

2. Attaching the side handle (Fig. 10)

(1) Turn the grip of the side handle to loosen it and push it

in until it comes in contact with the gear cover.

(2) Adjust the side handle to the angle that allows the

easiest use, then turn the side handle’s grip ﬁ rmly to

lock it place.

Loosen Tighten

Gear cover

Side handle

Fig. 10

3. Mounting the drill bit (Fig. 11, 12)

WARNING

To prevent accidents, make sure to turn the

switch oﬀ and disconnect the battery when the

drill bits and other various parts are installed or

removed.

NOTE

When using tools such as drill bits, etc., make sure to

use the genuine parts designated by our company.

(1) Clean, then smear the shank portion of the drill bit with

the grease or machine oil.

(2) Insert the drill bit in a twisting manner into the tool

holder until it latches itself. (Fig. 11)

The grip need not be adjusted during bit installation.

Drill bit Drill bit

Grease

Grip

Front cap

Fig. 11

(3) Check the latching by pulling on the drill bit.

14

English

(4) To remove the drill bit, fully pull the grip in the direction

of the arrow and pull out the drill bit. (Fig. 12)

Drill bit

Grip

Front cap

Fig. 12

4. Installation of dust cup or dust collector (B) (Optional

accessories) (Fig. 13, Fig. 14)

When using a rotary hammer for upward drilling

operations attach a dust cup or a dust collector (B)

to collect dust or particles for easy operation.

○

Installing the dust cup

Use the dust cup by attaching to the drill bit as shown

in Fig. 13.

When using a bit which has big diameter, enlarge the

center hole of the dust cup with this rotary hammer.

○

Installing dust collector (B)

When using dust collector (B), insert dust collector (B)

from the tip of the bit by aligning it to the groove on the

grip. (Fig. 14)

Dust cup

Fig. 13

Dust collector (B)

Fig. 14

CAUTION

●

The dust cup and dust collector (B) are for

exclusive use of concrete drilling work. Do not

use them for wood or metal drilling work.

●

Insert the dust collector (B) completely so that it

ﬁ ts tightly against the front cap.

●

If the rotary hammer is switched on while the

dust collector (B) is not in contact with a concrete

surface, the dust collector (B) may rotate together

with the drill bit, causing the dust collector (B) to

detach from the grip. Make sure to turn on the

switch after pressing dust cup on the concrete

surface. When using dust collector (B) attached

to a drill bit that has more than 7-15/32" (190 mm)

of overall length, dust collector (B) cannot touch

the concrete surface and will rotate. Therefore,

please use dust collector (B) by attaching to

drill bits which have 6-17/32" (166 mm), 6-19/64"

(160 mm), and 4-21/64" (110 mm) overall length.

●

Dump particles after every two or three holes

when drilling.

●

Please replace the drill bit after removing dust

cup, dust collector (B).

5. Selecting the driver bit

Screw heads or bits will be damaged unless a bit

appropriate for the screw diameter is employed to

drive in the screws.

6. Conﬁ rm the direction of bit rotation (Fig. 15)

The bit rotates clockwise (viewed from the rear side)

by pushing the R-side of the pushing button. (Fig. 15)

The L-side of the pushing button is pushed to turn the

bit counterclockwise.

Pushing button

Fig. 15

CAUTION

The pushing button cannot be switched while

the power tool is turning. To switch the pushing

button, stop the power tool, then set the pushing

button.

15

English

7. About remaining battery indicator

You can check the battery’s remaining capacity by

pressing the remaining battery indicator switch to light

the indicator lamp. (Fig. 16, Table 5)

The indicator will shut oﬀ approximately 3 seconds

after the remaining battery indicator switch is pressed.

It is best to use the remaining battery indicator as

a guide since there are slight diﬀ erences such as

ambient temperature and the condition of the battery.

Also, the remaining battery indicator may vary from

those equipped to a tool or charger.

Table 5

State of lamp Battery Remaining Power

Lights ;

The battery remaining power is

over 75%

Lights ;

The battery remaining power is

50%–75%.

Lights ;

The battery remaining power is

25%–50%.

Lights ;

The battery remaining power is

less than 25%

Blinks ;

The battery remaining power

is nearly empty. Recharge the

battery soonest possible

Blinks ;

Output suspended due to high

temperature. Remove the battery

from the tool and allow it to fully

cool down.

Blinks ;

Output suspended due to failure

or malfunction. The problem may

be the battery so please contact

your dealer.

As the remaining battery indicator shows somewhat

diﬀ erently depending on ambient temperature and

battery characteristics, read it as a reference.

Display panel

Remaining battery

indicator lamp Remaining battery

indicator switch

Fig. 16

NOTE

Do not give a strong shock to the display panel or

break it. It may lead to a trouble.

8. How to use the LED light

While the switch is pulled, the LED light will

automatically light up the tip portion of the tool.

(Fig. 17)

The LED light will automatically turn oﬀ 10 seconds

after the switch is released.

Switch trigger

LED light

Fig. 17

CAUTION

●

Do not expose directly your eye to the light by

looking into the light.

If your eye is continuously exposed to the light,

your eye will be hurt.

●

Wipe oﬀ any dirt or grime attached to the lens of

the LED light with a soft cloth, being careful not

to scratch the lens.

Scratches on the lens of the LED light can result

in decreased brightness.

16

English

9. Selecting the function mode

You can switch functions to the 3 modes of “hammering

only”, “rotation + hammering”, and “rotation only”

by turning the change lever while pressing the push

button. Set the mark position of the change lever to

that of the mode to be used.

CAUTION

●

Before operating the change lever, check and

make sure that the motor has stopped.

A failure can occur if it is operated while the

motor is running.

●

To operate the change lever, press the push

button, and release the lock of the change lever.

Also, check and make sure after operation

that the push button has returned and that the

change lever has been locked.

●

Switch the change lever without mistake.

If it is used at a position halfway, there is a fear

that the service life of the switching mechanism

may be shortened.

HOW TO USE

WARNING

To prevent accidents, make sure to turn the

switch oﬀ and disconnect the battery when the

drill bits and other various parts are installed

or removed. The power switch should also be

turned oﬀ during a work break and after work.

CAUTION

To extend the lifetime, the lithium-ion battery

equips with the protection function to stop the

output. Therefore, if the tool is overloaded, the

motor may stop. However, this is not the trouble

but the result of protection function. In this case,

release the switch of tool and eliminate the

causes of overloading.

1. Switch operation

○

When the switch trigger is depressed, the tool rotates.

When the switch trigger is released, the tool stops.

○

The rotational speed of the rotary hammer can be

controlled by varying the amount that the switch

trigger is pulled. Speed is low when the switch trigger

is pulled slightly and increases as the switch trigger is

pulled more.

○

When releasing the switch trigger, the brake will be

applied for immediate stopping.

2. Rotation + hammering

This rotary hammer can be set to rotation and

hammering mode by pressing the push button and

turning the change lever to the mark (Fig. 18).

Push button

Change lever

Fig. 18

(1) Mount the drill bit.

(2) Pull the trigger switch after applying the drill bit tip to

the drilling position (Fig. 19).

Fig. 19

(3) Pushing the rotary hammer forcibly is not necessary

at all. Pushing slightly so that drill dust comes out

gradually is suﬃ cient.

CAUTION

When the drill bit touches construction iron

bar, the bit will stop immediately and the rotary

hammer will react to revolve. Therefore please

grip the side handle and handle tightly as shown

in Fig. 19.

3. Rotation only

This rotary hammer can be set to rotation only mode

by pressing the push button and turning the change

lever to the mark (Fig. 20).

To drill wood or metal material using the drill chuck

and chuck adapter (optional accessories), proceed as

follows.

Installing drill chuck and chuck adapter. (Fig. 21)

Push button Change lever

Fig. 20

17

English

(1) Attach the drill chuck to the chuck adapter.

(2) The part of the SDS-plus shank is the same as the drill

bit. Therefore, refer to the item of “Mounting the drill

bit” for attaching it.

Front cap

Part of SDS-plus shank

Drill chuck Grip

Chuck adapter

Fig. 21

CAUTION

●

Do not apply excessive force during operation.

Doing so will not only damage the tip of the drill

bit, but also reduce the service life of the rotary

hammer.

●

Drill bits may snap oﬀ while withdrawing

the rotary hammer from the drilled hole. For

withdrawing, it is important to use a pushing

motion.

●

Do not attempt to drill anchor holes or holes in

concrete with the machine set in the rotation

only function.

●

Do not attempt to use the rotary hammer in

the rotation and striking function with the drill

chuck and chuck adapter attached. This would

seriously shorten the service life of every

component of the machine.

4. When driving machine screws (Fig. 22)

First, insert the bit into the socket in the end of chuck

adapter (D).

Next, mount chuck adapter (D) on the main unit using

procedures described in 3 (1), (2), (3), put the tip of the

bit in the slots in the head of the screw, grasp the main

unit and tighten the screw.

Bit

Socket

Chuck adapter(D)

Front cap

Grip

Fig. 22

CAUTION

●

Exercise care not to excessively prolong driving

time, otherwise, the screws may be damaged by

excessive force.

●

Apply the rotary hammer perpendicularly to the

screw head when driving the screw; otherwise,

the screw head or bit will be damaged, or driving

force will not be fully transferred to the screw.

●

Do not attempt to use the rotary hammer in the

rotation and striking function with the chuck

adapter and bit attached.

5. When driving wood screws (Fig. 22)

(1) Selecting a suitable driver bit

Employ plus-head screws, if possible, since the driver

bit easily slips oﬀ the heads of minus-head screws.

(2) Driving in wood screws.

○

Prior to driving in wood screws, make pilot holes

suitable for them in the wooden board.

Apply the bit to the screw head grooves and gently

drive the screws into the holes.

○

After rotating the rotary hammer at low speed for a

while until the wood screw is partly driven into the

wood, squeeze the trigger more strongly to obtain the

optimum driving force.

CAUTION

Exercise care in preparing a pilot hole suitable

for the wood screw taking the hardness of the

wood into consideration. Should the hole be

excessively small or shallow, requiring much

power to drive the screw into it, the thread of the

wood screw may sometimes be damaged.

6. Hammering only

This rotary hammer can be set to hammering only

mode by pressing the push button and turning the

change lever to the mark (Fig. 23).

Push button

Change lever

Fig. 23

(1) Mount the bull point or cold chisel.

(2) Press the push button and set the change lever to

middle of mark and mark (Fig. 24).

The rotation is released, turn the cold chisel and

adjust the cold chisel to desired position (Fig. 25).

18

English

Push button

Change lever

Fig. 24

Fig. 25

(3) Turn the change lever to mark (Fig. 23).

Then bull point or cold chisel is locked.

7. Using depth gauge (Fig. 26)

(1) Loosen the knob on the side handle, and insert the

depth gauge into the mounting hole on the side

handle.

(2) Adjust the depth gauge position according to the

depth of the hole and thighten the knob securely.

Depth gauge Mounting hole

Side handle

Depth of the

hole

Fig. 26

8. How to use the drill bit (taper shank) and the taper

shank adapter

(1) Mount the taper shank adapter to the rotary hammer

(Fig. 27).

(2) Mount the drill bit (taper shank) to the taper shank

adapter (Fig. 27).

(3) Turn the switch ON, and drill a hole in prescribed

depth.

(4) To remove the drill bit (taper shank), insert the cotter

into the slot of the taper shank adapter and strike the

head of the cotter with a hammer supporting on the

rests (Fig. 28).

Drill bit

Front cap Grip

Taper shank adapter

Fig. 27

Cotter

Rest

Taper shank adapter

Fig. 28

OPERATIONAL CAUTIONS

Resting the unit after continuous work

(1) The power tool is equipped with a temperature

protection circuit to protect the motor.

Continuous work may cause the temperature of the

unit to rise, activating the temperature protection

circuit and automatically stopping operation.

If this happens, allow the power tool to cool before

resuming use.

(2) After use for continuous works, rest the unit for

15 minutes or so when replacing the battery. The

temperature of the motor, switch, etc., will rise if

the work is started again immediately after battery

replacement, eventually resulting in burnout.

19

English

SELECT OPERATION MODE

Pressing the changeover switch allows the selection of

rotation speed and the auto stop function.

○

Rotation speed (Low mode/Normal mode) (Fig. 29)

Select either Low mode or Normal mode and operate

the tool in the selected speed.

Changeover switch Display lamp

Lighting status of display lamp

Number of rotations ( /min) 700 950

Number of impacts ( /min) 3,170 4,300

Fig. 29

○

Auto stop mode (on/oﬀ ) (Fig. 30)

This product is equipped with an auto stop function

to support continuous drilling work. The function

features a memory mode for storing the work time

for drilling from switch ON to switch OFF, and an auto

stop mode that automatically stops the motor from the

second drilling onward should the work exceed the

stored work time while the switch is ON.

AUTO STOP FUNCTION

In selection mode, pressing the button for longer than two

seconds will move to memory mode. (Fig. 30)

Changeover switch

Auto stop lamp: Blinks

Auto stop lamp: Lights

Fig. 30

(At the same time the auto stop lamp will blink.)

Conduct drilling when the auto stop lamp is ﬂ ashing. The

time between switching ON and switching OFF is stored

by the tool.

(At the same time, the auto stop lamp will light up.)

Conduct drilling when the auto stop lamp is ﬂ ashing.

Continuous drilling is possible as the memory storage time

will be recorded by the tool until the auto stop function’s

auto stop mode is cancelled.

The auto stop function is cancelled by pressing the

changeover switch once again for over two seconds.

(At the same time, the auto stop lamp will switch oﬀ .)

CAUTION

○

Switch ON the tool once you place the tip of the tool

on the work material.

○

The rotation speed and the level at which the switch is

pulled during drilling is not stored to memory.

○

Fully carry out drilling in one go during auto stop

mode.

○

The motor will stop even if you switch OFF within the

memory storage time.

○

When you switch OFF within the memory storage

time, the count will be reset. If you rework a task in

which a hole has been partially drilled, the memory

storage time will be fully recounted.

○

The auto stop function will remain active until

canceled.

20

English

REACTIVE FORCE CONTROL

This product is equipped with a Reactive Force Control

(RFC) feature that reduces jerking of the tool body.

If the tool bit is suddenly overburdened, any jerking of the

tool body is reduced by activation of the slip clutch or by

stopping of the motor by the sensor built into the tool body.

If the motor is stopped because of overburdening detection

by the controller, the RFC indicator lamp (display lamp) will

blink while the switch is pulled. In addition, the lamp will

continue blinking for approximately three seconds after

the switch is released. The motor will remain stopped

while the lamp is blinking. (Fig. 31)

Because the RFC feature may not activate or its

performance may be insuﬃ cient depending on the

working environment and conditions, be careful not to

suddenly overburden the tool bit while operating.

●

Possible causes of sudden overburdening

Tool bit biting into material

Impact against nails, metal or other hard objects

Tasks involving prying or any excess application of

pressure, etc.

Also, other causes include any combination of the

aforementioned.

●

When the reactive force control (RFC) is triggered

When the RFC is triggered and the motor stops, turn

oﬀ the tool’s switch and remove the cause of the

overburdening before continuing operation.

Fig. 31

ABOUT THE PROTECTION FUNCTION

This tool has a built-in protection circuit for preventing

damage to the unit in the event of an abnormality.

Depending on the following, the display lamp and the

indicator lamp will ﬂ ash, and the unit will cease to operate.

Verify the problem indicated by the ﬂ ashing and take the

necessary steps to correct the problem.

When pressing the changeover switch, do so when the

switch is not being pulled.

Changeover switch

Display lamp

Fig. 32

Table 6

Display

lamp

ﬂ ashing Cause Solution

Operation has

ceased because

the internal

temperature has

exceeded the

temperature limit.

(High temperature

protection function)

Allow the unit to cool

for 15 to 30 minutes.

When the

temperature goes

down and the display

lamp blinking stops,

pull the switch trigger

to recover operation.

Sudden

overburdening of

the tool bit has

activated the RFC,

stopping further

operation of the

tool.

RFC (See page 20

“REACTIVE

FORCE

CONTROL”)

Release the switch

trigger and leave it

until the display lamp

blinking stops. Pull

the switch trigger

again to recover

operation.

Before continuing

operation, remove

the cause of the

overburden.

NOTE

Despite taking steps to correct a problem, the display

lamp may continue to blink. Should this be the case,

the unit may require repair. If so, please contact the

outlet from which this product was purchased for

repairs.

La page charge ...

Hikoki DH1826DA Manuel utilisateur

Hikoki DH1826DA Manuel utilisateur

dans d''autres langues

Documents connexes