PAX M8 Guide d'installation

Catégorie
Les smartphones
Taper
Guide d'installation
M8 PayTablet
PAX TECHNOLOGY LIMITED
Installation Manual
1. Contents Checklist
Please check the components after unpacking. If any are missing, please contact the
dealer.
Name
Qty.
M8 PayTablet
1
AC Power Adapter
1
USB Cable
1
Mobile phone Card Pick-up Needle
1
Product Manual
1
2. Product Description
Rear-Camera
Flash Light
Macro Camera
NFC Reading area
Touch Keypad
Bottom View
3. Installation
TYPE_C port: Connect USB device or PC.
6pin_Pogopin port: Connect deviceMSR/Barcode etc.
SIM card (optional):
1Take the Card Pick-up Needle out of the box;
TYPE-C
Speaker
Main-MIC
Volume +
Volume -
Power Button
SIM/microSD
Card-Slot
IC Card-Slot
Proximity Sensor
Front Camera
TOP View
Type-C
Sub-MIC
Audio Jack
6pin Pogo Pin
8 inch LCD
Touch Screen
Pogo Pin
2Insert the Card Pick-up Needle into the SIM card slot;
3Insert SIM card into the pop-up card-slot.
microSD card:
1Take the Card Pick-up Needle out of the box;
2Insert the Card Pick-up Needle into the microSD card slot;
3Insert microSD card into the pop-up card-slot.
4. Instructions
1 Power ON/OFF
Power on: press and hold the Power button for five seconds until the LCD besides, and
then the terminal is being turned on.
Power off: press and hold the Power button for three seconds until the shutdown menu
appears, tap Shutdown > Click Shutdown, and then “Shutting…” appears, the
terminal is being turned off.
2IC card
Place the chip face up, insert the IC card into the IC card slot, and push it to the end.
microSD
Nano SIM
Nano SIM
3Swiping contactless card
Place a contactless card close to the sensor area of swiping which is at the back of the
terminal.
5. Installation and Usage Tips
1Avoid putting the terminal in direct sunlight, high temperature, moist, or dusty
environment.
2Forbid non-professional to repair the terminal.
3Before insert the card, please check internal and around of IC card slot. When you
found some suspicious objects, must report to related administrator.
Working Environment Temperature: -10~45(14~113)
R.H.:5%~96% (non-condense)
Storage Environment Temperature: -20~70(-4~158)
R.H.:5%~96% (non-condense)
6. Important Safety Warning
1) Do not place the terminal/battery under direct sunlight, high temperature, smoke,
dust, and damp environment.
2) Not allowed to place battery in fire, disassemble, drop, squeeze, or modify battery to
avoid having foreign object insert and penetrate the battery, to avoid merge the battery
into the liquid. External shock and pressure may cause battery liquid leak, overheat fire
or explosion. Please keep battery away from children and animals to avoid injury or
explosion.
3) Must stop using the battery immediately and replace with a new one if the battery
expanded, bent, damaged, or overheated.
4) Recommend using the equipped power adaptor or use a3rd. party power adaptor that
its specifications match the device equipped power adaptor and meets the country/local
region regulations and international and regional safety standards. Non-compatible
power supply, charger or battery may cause fire, explosion and other dangerous.
5) Battery charging time can not be more than 24 hours. Please charge the battery when
the battery level is too low. If the battery is not being used for a long time to avoid
battery over charge and discharge damage, please charge the battery once every six
months.
6) Recommend replacing the battery after two-years continuous use.
7) Please dispose the device, battery, and its accessories according to the local
regulations. They can not be disposed as household waste. Improper dispose the battery
may cause battery explosion.
7. Icons
Do not throw away, need professional recycling.
Class II Equipment
For indoor use only
Energy Efficiency Marking
AC voltage
DC voltage
Trademark notice:
microSD logo is a trademark of SD-3C LLC.
For this device, the highest reported SAR value for usage near the body is 1.34 W/kg.
The full text of the EU declaration of conformity is available at the following internet address:
https://www.pax.com.cn/ProductCE/index.aspx
E-Label
This device has E-Lable, Steps to access the e-label is SettingAbout phone---Regulatory labels.
1Click--Setting 2Click--About phone
3Click--Regulatory labels 4Content
FCC compliance statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
changes or modifications not expressly approved by the party responsible for compliance could void the users
authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
FCC SAR statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End user
must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be
co-located or operating in conjunction with any other antenna or transmitter.
The portable device is designed to meet the requirements for exposure to radio waves established by the Federal
Communications Commission (USA). These requirements set a SAR limit of 1.6 W/kg averaged over one gram of
tissue. The highest SAR value reported under this standard during product certification for use when properly
worn on the body
ISED compliance statement
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and
Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired operation of the
device.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation,
Sciences et Développement économique Canada applicables aux appareils radio exempts de licence.
L’exploitation est autorisée aux deux conditions suivantes :
(1) L’appareil ne doit pas produire de brouillage;
(2) Lappareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible den
compromettre le fonctionnement.
The user manual for LE-LAN devices shall contain instructions related to the restrictions mentioned in the above
sections, namely that:
i. the device for operation in the band 51505250 MHz is only for indoor use to reduce the potential for
harmful interference to co-channel mobile satellite systems;
ii. where applicable, antenna type(s), antenna models(s), and worst-case tilt angle(s) necessary to remain
compliant with the e.i.r.p. elevation mask requirement set forth in section 6.2.2.3 shall be clearly
indicated.
i. le dispositif utilisé dans la bande 5150-5250 MHz est réservé à une utilisation en intérieur afin de
duire le risque de brouillage préjudiciable aux systèmes mobiles par satellite dans le même canal;
ii. èle (s) d'antenne et l'angle (s) d'inclinaison le plus défavorable nécessaire (s) pour rester conforme (e)
au p.e. L'exigence relative au masque d'élévation énoncée à la section 6.2.2.3 doit être clairement
indiquée.
IC SAR statement
This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. End user
must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not
be co-located or operating in conjunction with any other antenna or transmitter.
The portable device is designed to meet the requirements for exposure to radio waves established by the ISED.
These requirements set a SAR limit of 1.6 W/kg averaged over one gram of tissue. The highest SAR value reported
under this standard during product certification for use when properly worn on the body.
Cet équipement est conforme aux limites dexposition aux rayonnements ISED établies pour un environnement
non contrôlé. L’utilisateur final doit suivre les instructions spécifiques pour satisfaire les normes. Cet émetteur ne
doit pas être co-implanté ou fonctionner en conjonction avec toute autre antenne ou transmetteur.
Le dispositif portatif est conçu pour répondre aux exigences d’exposition aux ondes radio établie par le
développement énergétique DURABLE. Ces exigences un SAR limite de 1,6 W/kg en moyenne pour un gramme de
tissu. La valeur SAR la plus élevée signalée en vertu de cette norme lors de la certification de produit à utiliser
lorsqu’il est correctement porté sur le corps.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9

PAX M8 Guide d'installation

Catégorie
Les smartphones
Taper
Guide d'installation

dans d''autres langues