Husqvarna BMS 220 ADB Manuel utilisateur

Taper
Manuel utilisateur
BMS 220 ADB
EN Operator's manual 2-24
DE Bedienungsanweisung 25-48
FR Manuel d'utilisation 49-72
NL Gebruiksaanwijzing 73-96
Contents
Introduction..................................................................... 2
Safety..............................................................................4
Operation........................................................................ 8
Maintenance................................................................. 13
Troubleshooting............................................................ 18
Transportation, storage and disposal........................... 18
Technical data.............................................................. 20
Accessories.................................................................. 22
Declaration of Conformity............................................. 24
Introduction
Product description
The product is a ride-on floor scraper for surfaces of
different hardness.
Intended use
The product is used to remove surface materials with
different hardness from concrete floors, wood floors and
soft subfloors. Use the product to remove hardwood,
ceramics, linoleum, vinyl, carpet, adhesives and glue.
Do not use the product for other tasks.
The product is used in industrial operations by
professional operators.
21813 - 001 - 11.05.2022
Product overview BMS 220ADB
1
2
3
10
9
8
7
6
12
11
4
15
13
18
16
17
19
5
14
1. Blade holder
2. Tool holder
3. Electrical enclosure
4. Batteries
5. Type plate
6. Right movement control
7. Tool height handle
8. Emergency stop button
9. Battery status indicator/hour meter
10. ON/OFF key
11. Tool angle handle
12. Left movement control
13. Adjustable seat
14. Charge indicator hatch
15. Box with motor and hydraulic oil pumps
16. Connector for battery charger
17. Wheel scrapers
18. Hydraulic oil filter
19. Operator's manual
Symbols on the product
Warning: This product can be dangerous
and cause serious injury or death to the
1813 - 001 - 11.05.2022 3
operator or others. Be careful and use the
product correctly.
High voltage.
Keep all parts of your body away from hot
surfaces.
Lifting point.
Read the manual carefully and make
sure that you understand the instructions
before you use the product.
Use an approved respiratory protection.
Use approved hearing protection.
Use approved eye protection.
Use approved protective gloves.
Use approved protective boots
This product is in compliance with
applicable EU directives.
Note: Other symbols/decals on the product refer to
special certification requirements for some markets.
Type plate
13
11
10
12
21 3 4
6
5
8
9
7
1. Product number
2. Product weight
3. Rated power
4. Rated voltage
5. Enclosure
6. Rated current
7. Frequency
8. Maximum slope angle
9. Manufacturer
10. Scannable code
11. Production year
12. Model
13. Serial number
Product liability
As referred to in the product liability laws, we are not
liable for damages that our product causes if:
the product is incorrectly repaired.
the product is repaired with parts that are not
from the manufacturer or not approved by the
manufacturer.
the product has an accessory that is not from the
manufacturer or not approved by the manufacturer.
the product is not repaired at an approved service
center or by an approved authority.
Safety
Safety definitions
Warnings, cautions and notes are used to point out
specially important parts of the manual.
WARNING: Used if there is a risk of
injury or death for the operator or bystanders
if the instructions in the manual are not
obeyed.
41813 - 001 - 11.05.2022
CAUTION: Used if there is a risk of
damage to the product, other materials or
the adjacent area if the instructions in the
manual are not obeyed.
Note: Used to give more information that is necessary
in a given situation.
General safety instructions
WARNING: Read the warning
instructions that follow before you use the
product.
This product is a dangerous tool if you are not
careful or if you use the product incorrectly. This
product can cause serious injury or death to the
operator or others. Before you use the product,
you must read and understand the contents of this
operator’s manual.
Save all warnings and instructions.
Comply with all applicable laws and regulations.
The operator and the employer of the operator must
know and prevent the risks during operation of the
product.
Do not let a person operate the product unless they
read and understand the contents of the operator's
manual.
Do not operate the product unless you receive
training before use. Make sure that all operators
receive training.
Do not let a child operate the product.
Only let approved persons operate the product.
The operator is responsible for accidents that occur
to other persons or their property.
Do not use the product if you are tired, ill, or under
the influence of alcohol, drugs or medicine.
Always be careful and use your common sense.
Keep the product clean. Make sure that you can
clearly read signs and decals.
Do not use the product if it is defective.
Do not do modifications to this product.
Do not operate the product if it is possible that other
persons have done modifications to the product.
Safety instructions for operation
WARNING: Read the warning
instructions that follow before you use the
product.
Use personal protective equipment. Refer to
Personal protective equipment on page 6
.
Overexposure to vibration can cause circulatory
damage or nerve damage to persons with decreased
blood circulation. Get medical aid if you have
symptoms of overexposure to vibration. These
symptoms include numbness, loss of feeling,
tingling, pricking, pain, loss of strength, changes
in skin color or condition. These symptoms usually
show in the fingers, hands or wrists.
Do not operate the product without all protective
covers installed.
Make sure that you know how to stop the motor
quickly in an emergency.
Before you go away from the product, stop the motor
and disconnect the power cord. Make sure that there
is no risk of accidental start.
Make sure that clothing, long hair and jewelry do not
get caught in moving parts
Make sure that you are in a safe and stable position
during operation.
Only operate the product on horizontal surfaces.
Do not operate the product unless you can get aid if
an accident occurs
Always use approved accessories. Speak to your
Husqvarna dealer for more information.
If vibrations occur in the product or the noise level
from the product is unusually high, stop the product
immediately. Examine the product for damages.
Repair damages or let an approved service agent
do the repair.
Always use the seatbelt during operation.
Disconnect the battery charger before operation.
Vibration safety
WARNING: Read the warning
instructions that follow before you use the
product.
During operation of the product, vibrations go from
the product to the operator. Regular and frequent
operation of the product can cause or increase the
degree of injuries to the operator. Injuries can occur
in fingers, hands, wrists, arms, shoulders, and/or
nerves and blood supply or other body parts. The
injuries can be debilitating and/or permanent, and
can increase gradually during weeks, months or
years. Possible injuries include damage to the blood
circulation system, the nervous system, joints, and
other body structures.
Symptoms can occur during operation of the product
or at other times. If you have symptoms and
continue to operate the product, the symptoms can
increase or become permanent. If these or other
symptoms occur, get medical aid:
Numbness, loss of feeling, tingling, pricking,
pain, burning, throbbing, stiffness, clumsiness,
loss of strength, changes in skin color or
condition.
Symptoms can increase in cold temperatures. Use
warm clothing and keep your hands warm and dry
when you operate the product in cold environments.
1813 - 001 - 11.05.2022 5
Do maintenance on and operate the product as
given in the operator's manual, to keep a correct
vibration level.
The product has a vibration damping system that
decreases the vibrations from the handles to the
operator. Let the product do the work. Do not
push the product with force. Hold the product at
the handles lightly, but make sure that you control
the product and operate it safely. Do not push the
handles into the end stops more than necessary.
Keep your hands on the handle or handles only.
Keep all other body parts away from the product.
Stop the product immediately if strong vibrations
suddenly occurs. Do not continue the operation
before the cause of the increased vibrations is
removed.
Noise safety
WARNING: Read the warning
instructions that follow before you use the
product.
High noise levels and long-term exposure to noise
can cause noise-induced hearing loss.
To keep the noise level to a minimum, do
maintenance on and operate the product as given
in the operator's manual.
Use approved hearing protection while you operate
the product.
Listen for warning signals and voices when you use
hearing protection. Remove the hearing protection
when the product is stopped, unless hearing
protection is necessary for the noise level in the work
area.
Personal protective equipment
WARNING: Read the warning
instructions that follow before you use the
product.
Always use approved personal protective equipment
when you operate the product. Personal protective
equipment cannot fully prevent injury but it
decreases the degree of injury if an accident does
occur. Let your dealer help you select the correct
personal protective equipment.
Regularly do a check of the condition of the personal
protective equipment.
Use an approved protective helmet.
Use approved hearing protection.
Use approved respiratory protection.
Use approved eye protection with side protection.
Use protective gloves.
Use boots with steel toe-cap and non-slip sole.
Use approved work clothing or equivalent close-
fitting clothing that has long sleeves and long legs.
Fire extinguisher
Keep a fire extinguisher near during operation.
Use a powder fire extinguisher or a carbon dioxide
fire extinguisher.
Work area safety
WARNING: Read the warning
instructions that follow before you use the
product.
Do not use the product in fog, rain, strong winds,
cold weather, risk of lightning or other bad weather
conditions.
Do not use the product in areas where fire or
explosions can occur.
Keep children, bystanders and animals away from
the work area and at a safe distance from the
product.
Make sure that only approved persons are in the
work area.
Keep the work area clean and sufficiently
illuminated.
Remove objects such as screws, bolts, wires and
stones from the work area before you use the
product.
Make sure that there are no cables or hoses in the
operation direction of the product.
Make sure that there is sufficient airflow in the work
area.
Electrical safety
WARNING: There is always a risk of
shocks from electrical products. Do not use
the product in bad weather conditions. Do
not touch lightning conductors and metal
objects. Always use the product as given in
this operator’s manual to prevent injury.
WARNING: Always use a power supply
with RCD (residual-current device). An RCD
decreases the risk of electrical shock.
WARNING: High voltage. There are
unprotected parts in the power unit. Always
disconnect the power plug before you open
the door to the electrical box.
CAUTION: The power supply from the
product or generator must be sufficient and
constant to make sure that the charger
operates without problems. Incorrect voltage
causes the power consumption and the
temperature of the charger to increase until
the safety circuit releases. The dimension
of the power cord must agree with national
61813 - 001 - 11.05.2022
and local regulations. The dimension of the
mains socket must agree with the amperage
for the electrical socket and extension cable
of the product.
If the power mains has higher system
resistance, short voltage drop can occur
when the product is charged. This can
influence the operation of other products, for
example flicker on the lights.
Make sure that the power, fuse and mains voltage
are the same as the voltage shown on the rating
plate of the product.
Do not use the product if the power cord or power
plug is damaged. Hand it in to an approved service
center for repair. A damaged power cord can cause
serious injury and death.
Use the power cord correctly. Do not use the power
cord to move, pull or disconnect the product. Pull the
power plug to disconnect the power cord. Do not pull
the power cord.
Do not operate the product in water depths where
the equipment of the product gets wet. The
equipment can become damaged and the product
can become live and cause injury.
Do not get more moisture into the product than
the water supplied by the water system. Keep the
product away from rain. Water that goes into the
product increases the risk of electrical shock.
Always disconnect the power cord before you
connect or disconnect the electrical enclosure.
Grounded product instructions
WARNING: Incorrect connection can
result in electrical shock. Speak to an
approved electrician if you are not sure if
your mains outlet is correctly grounded.
Do not do modifications to the power plug
from its factory specification. If the power
plug or power cord is damaged or must be
replaced, speak to your Husqvarna service
agent. Obey local regulations and laws.
If you do not fully understand the
instructions about the grounded product,
speak to an approved electrician.
Use only grounded outdoor extension cables with
grounding plugs and grounding outlet that accepts the
product power plug.
The product has a grounded power cord and power
plug. Always connect the product to a grounded mains
outlet. This decreases the risk of electrical shock if there
is a malfunction.
Do not use electrical adapters with the product.
Safety devices on the product
WARNING: Read the warning
instructions that follow before you use the
product.
Do not use a product with defective safety devices.
Do a check of the safety devices regularly. If
the safety devices are defective, speak to your
Husqvarna service agent.
Seat belt
WARNING: Always use the seat belt
when you operate the product.
The seat belt will keep the operator in the seat in an
emergency stop.
Keep the seat belt flat against your waist.
Do not twist the seat belt.
Make sure that there are no objects between you
and the seat belt.
Do a check of the seat belt after an emergency stop.
Make sure that the function of the seat belt is correct
before you use the product.
Keep the seat belt clean and dry.
Emergency stop button
The emergency stop button is used to quickly stop the
motor.
To do a check of the emergency stop button
Refer to
Product overview BMS 220ADB on page 3
for
information about where the emergency stop button is
on your product.
1. Turn the emergency stop button clockwise to make
sure that the emergency stop button is disengaged.
2. Start the product. Refer to
To start the product on
page 9
.
3. Push the emergency stop button.
4. Make sure that the motor stops.
5. Turn the emergency stop button clockwise to
disengage.
Operator Presence Control (OPC)
When the OPC is engaged, the motor stops. Refer to
To do a check of the operator presence control on page
7
.
To do a check of the operator presence control
1. Start the product. Refer to
To start the product on
page 9
.
1813 - 001 - 11.05.2022 7
2. Leave the seat to engage the operator presence
control. If the motor does not stop in 3 seconds,
speak to an approved Husqvarna service agent.
Dust safety
WARNING: Read the warning
instructions that follow before you use the
product.
Operation of the product can cause dust in the
air. Dust can cause serious injury and permanent
health problems. Silica dust is regulated as harmful
by several authorities. These are examples of such
health problems:
The fatal lung diseases chronic bronchitis,
silicosis and pulmonary fibrosis
• Cancer
Birth defects
Skin inflammation
Use correct equipment to decrease the quantity of
dust and fumes in the air and to decrease dust on
work equipment, surfaces, clothing and body parts.
Examples of controls are dust collection systems
and water sprays to bind dust. Decrease dust at
the source where possible. Make sure that the
equipment is correctly installed and used and that
regular maintenance is done.
Use approved respiratory protection. Make sure
that the respiratory protection is applicable for the
dangerous materials in the work area.
Make sure that the airflow is sufficient in the work
area.
If it is possible, point the exhaust of the product
where it cannot cause dust to go into the air.
Battery safety
WARNING: Read the warning
instructions that follow before you use the
product.
Only use approved batteries.
Do not use a defective or damaged battery.
Only let an approved service center do servicing on
the batteries.
If the battery leaks, do not let the liquid touch your
body or eyes. If you have touched the liquid, clean
the area with a large quantity of water and soap, and
get medical aid. If you get liquid in your eyes, do not
rub but flush with water for a minimum of 15 minutes
and get medical aid.
Risk of electrical shock. Do not connect the battery
terminals to keys, coins, screws or other metal. This
can cause a short circuit of the battery.
Keep the battery away from sunlight, heat or open
flame. The battery can cause burns and/or chemical
burns.
Keep batteries in storage away from metal objects
such as nails, screws or jewelry.
Safety instructions for maintenance
WARNING: Read the warning
instructions that follow before you use the
product.
Use personal protective equipment. Refer to
Personal protective equipment on page 6
.
Only do the maintenance as given in this operator's
manual. Let an approved service agent do all other
servicing.
If the maintenance is not done correctly and
regularly, the risk of injury and damage to the
product increases.
Clean the product to remove dangerous material
before you do the maintenance.
Before you do the maintenance, do these steps:
Disconnect the power plug to the battery charger.
Turn the ON/OFF key to OFF and remove it.
Push the emergency stop button.
Do the maintenance of the product on stable level
ground.
Do not do modifications to the product. Modifications
that are not approved by the manufacturer can
cause serious injury or death.
Replace damaged, worn or broken parts.
Always use original accessories and spare parts.
Accessories and spare parts that are not approved
by the manufacturer, can cause serious injury or
death.
After maintenance, do a check of the vibration level
in the product. If it is not correct, speak to an
approved service agent.
Let an approved service agent do servicing on the
product regularly.
Operation
Introduction
WARNING: Before you operate the
product, you must read and understand the
safety chapter.
To do before you operate the product
1. Read the operator's manual carefully and make sure
that you understand the instructions.
2. Use personal protective equipment. Refer to
Personal protective equipment on page 6
.
81813 - 001 - 11.05.2022
3. Do daily maintenance. Refer to
Maintenance
schedule on page 13
.
4. Make sure that the product is assembled correctly
and is not damaged.
5. Make sure that only approved persons are in the
work area.
6. Disconnect the cable to the battery charger and put
the cable in the product. Refer to
To charge the
product on page 10
.
7. Put the product on the work area. Make sure that
the transportation of the product to and in the work
area is done safely and correctly. Refer to
Work area
safety on page 6
.
8. Install a tool. Refer to
To replace the blade on page
15
. Make sure that the tool has the correct angle
and pitch for the operation.
9. Make sure that the blade is sharp. If it is necessary,
replace or sharpen the blade. Refer to
To replace
the blade on page 15
and
To sharpen the blade on
page 15
.
10. If you use a self-scoring blade, make sure that the
angles at the ends of the blade (A) are sharp.
A
To select the correct blade dimension
and installation position
WARNING: Use protective gloves. The
blades are very sharp.
All available blade types can be used for the approved
materials: hardwood, ceramics, linoleum, vinyl, carpet,
adhesives and glue. Refer to
Blade applications on page
12
.
It is necessary to select correct dimension and
installation of the blade for the material to remove and
the subfloor type. Blades of different dimension can be
necessary during the same work operation.
Select a blade of smaller dimension in these
situations:
a) At the start of an operation.
b) Operation on materials with strong adhesive.
c) Operation on hard materials.
Select a blade of wider dimension in these
situations:
a) Operation on soft materials.
Select a thicker heavy duty blade for hard materials.
A thicker blade also has a longer life.
Install the blade with the bevel up for removal of
materials from concrete floors.
Install the blade with the bevel down for removal of
materials from wood floors and soft subfloors.
To start the product
1. Sit on the seat, put your feet on the footrests and
fasten the seat belt.
2. Set the movement controls in neutral position.
3. Pull the emergency stop button out.
4. Turn the ON/OFF key clockwise.
5. Look at the battery status indicator to make sure that
the batteries are sufficiently charged.
To operate the product
1. Operate the movement controls to move the product.
Refer to
Product overview BMS 220ADB on page 3
.
a) To move the product forward, push the
movement controls forward.
b) To move the product rearward, pull the
movement controls rearward.
1813 - 001 - 11.05.2022 9
c) To turn to the right, push the left movement
control forward.
d) To turn to the left, push the right movement
control forward.
e) To turn clockwise around the product axis, push
the left movement control forward and pull the
right movement control rearward.
f) To turn counterclockwise around the product
axis, push the right movement control forward
and pull the left movement control rearward.
2. Adjust the speed with the movement controls.
a) Push or pull the movement controls a small
distance for slow speed.
b) Push or pull the movement controls a long
distance for high speed.
To adjust the angle of the tool
Operate the tool angle handle (A) to adjust the angle
of the tool.
A
B
C
Note: The tool angle handle controls the hydraulic
piston (B) and the angle of the tool holder (C).
To adjust the height of the tool
Operate the tool height handle (A) to adjust the
height of the tool.
A
C
B
Note: The tool height handle controls the hydraulic
piston (B) and the height of the tool holder (C).
To stop the product
1. Park the product in a safe area. Refer to
Work area
safety on page 6
.
2. Set the movement controls in neutral position.
3. Turn the ON/OFF key counterclockwise to the OFF
position.
4. Release the seat belt.
5. Charge the product. Refer to
To charge the product
on page 10
.
To charge the product
Note: Always keep the product connected to a mains
socket when it is not in operation. The firmware in the
charger will control the level of charge in the batteries.
CAUTION: Do not operate the product
while the charger is connected to a mains
socket. This will cause damage to the
charger.
1. Make sure that the ON/OFF key is in the OFF
position.
10 1813 - 001 - 11.05.2022
Note: The product does not charge when the
ON/OFF key is in the ON position.
2. Connect the charger and keep the charger
connected until the next time you use the product.
To remove a soft floor surface
WARNING: Use protective gloves. The
blades are very sharp.
Note: Short blades cut the floors easier than long
blades. Long blades are not always better or faster. A
short blade usually cleans the floor better than a wide
blade.
Note: The blades are sharp for a longer time if the
work area is clean from unwanted material.
1. Use personal protective equipment. Refer to
Personal protective equipment on page 6
.
2. Install a self scoring blade. Refer to
To select the
correct blade dimension and installation position on
page 9
and
To replace the blade on page 15
.
WARNING: Use protective gloves.
The blades are very sharp.
3. Make sure that the blade is sharp. Sharpen the
blade if it is necessary. Refer to
To sharpen the
blade on page 15
.
4. Cut a linear ditch in the floor.
5. Install a flat blade.
WARNING: Use protective gloves.
The blades are very sharp.
6. Start at the ditch and remove the floor.
1
2
To remove a hard floor surface
WARNING: Use protective gloves. The
blades are very sharp.
Note: Short blades cut the floors easier than long
blades. Long blades are not always better or faster. A
short blade usually cleans the floor better than a wide
blade.
Note: The blades are sharp for a longer time if the
work area is clean from unwanted material.
1. Use personal protective equipment. Refer to
Personal protective equipment on page 6
.
2. Install a short blade of the correct type. Refer to
To
select the correct blade dimension and installation
position on page 9
and
To replace the blade on page
15
.
WARNING: Use protective gloves.
The blades are very sharp.
3. Make sure that the blade is sharp. Sharpen the
blade if it is necessary. Refer to
To sharpen the
blade on page 15
.
1813 - 001 - 11.05.2022 11
4. Cut linear ditches in the floor. Make sure that the
distance between the ditches is the same as the
width of the long blade.
5. Install a long blade of the correct type. Refer to
To
select the correct blade dimension and installation
position on page 9
and
To replace the blade on page
15
.
6. Make sure that the blade is sharp. Sharpen the
blade if it is necessary. Refer to
To sharpen the
blade on page 15
.
7. Remove the floor between the ditches.
Note: Use a chisel and move the product in a fan
shape pattern to remove tiles and floors made of
wood.
Blade applications
Floor type Blade application
VCT – Tile (Vinyl Composition
Tile)
Do not use a blade wider than the dimension of the tile being removed. If the tiles do
not come up clean or the machine jumps on top of the tiles, install a smaller blade
until proper blade size is found or use a smaller portion of the blade.
Vinyl-, Rubber, PVC, Direct
glued carpet
The carpet must be scored down (ditching) with a 152mm Self-Scoring blade for
correct removal. Pre-scored carpet (ditched) or pre-cut carpet makes the machine
easier to control and blades stay sharp longer. Normally 254 mm blades are used
on direct glued carpet, secondary backed, unitary, double glued, vinyl foam, ure-
thane foam. Latex foams are easy to remove with a 305 mm blade.
Ceramic (glued with double
duty or mud sets)
The ceramic tiles will have to be pre-broken with a mallet or large hammer before
removing them with the floorscraper. Use a large hammer to break away enough
tiles to create space for the machine or blade to fit in. Or start from a doorway. Use
slow speed and small blades or chisel. Keep work area clean to keep good wheel
contact with floor.
12 1813 - 001 - 11.05.2022
Floor type Blade application
Wood and wood like floors Pre-saw the wood with a circular saw. Pound down or remove any nails or metal
obstruction to avoid blade damage.
Glued hard wood flooring For correct removal of hardwood flooring (plank solid, plank laminated, parkay,
parquetry laminated), the flooring must be pre-sawed. This is done by using a
circular saw set at a depth of 99% of the thickness of the board, just missing the
subfloor surface. Draw chalk lines across the floor and pre-saw to blade width.
(every 152mm).
True parkay flooring scoring is not necessary. It will come up in small pieces. When
working over plywood sub-flooring, try to run machine in the same direction as the
grain in the wood. Blade in most cases bevel down. On solid wood floors like plank,
run in the same direction as the plank, not cross grain or cross plank. Removing the
front counterweights will help on all soft surfaces.
Concrete When working on concrete slab, normal blade position is bevel up for best perform-
ance, especially when cleaning adhesive. On occasion, bevel down gives better
blade life.
Maintenance
Introduction
WARNING: Before you do
maintenance, you must read and
understand the safety chapter.
For all servicing and repair work on the product, special
training is necessary. We guarantee the availability of
professional repairs and servicing. If your dealer is not
a service agent, speak to them for information about the
nearest service agent.
Maintenance schedule
* = General maintenance done by the operator. The
instructions are not given in this operator's manual.
X = The instructions are given in this operator's manual.
O = The instructions are not given in this operator's
manual. Let an approved service agent do the
maintenance.
Maintenance
Daily Week-
ly
Each
12
month
s
12 h
after
servic-
ing
Clean the product. X
Do a check of all safety devices. *
Do a check of the RCD. *
Do a check of the wear and sharpness of the blade. X
Make sure that all electrical connectors are clean. X
Make sure that the motors are clean. *
Clean the external surfaces of the product. X
Clean the internal components of the product. O
Do a general inspection. X
Make sure that all screws and nuts are tightened with the correct torque. X X
1813 - 001 - 11.05.2022 13
Maintenance
Daily Week-
ly
Each
12
month
s
12 h
after
servic-
ing
Do a check for oil leaks. X
Do a check of the wear and function of the seat belt. X
Use compressed air to clean the inner surface of the charger. X
Do a check of the wear and function of the front wheels. X
Replace the hydraulic oil. Refer to
To replace the oil and oil filter on page 16
. X
Do a complete servicing and cleaning of the product. O
To do a general inspection
Make sure that the nuts and screws on the product
are tightened.
Make sure that the cables on the product are not in a
position where they can become damaged.
Examine the electrical parts for damage. Do not
operate a product that has damaged electrical parts.
To clean the product
Always clean all the equipment after use. Use a
vacuum cleaner.
Do not use a high-pressure washer to clean the
product.
Keep the air openings clean and clear to make
sure that the product always has sufficiently cool
temperature.
To adjust the tracking
If the product does not move straight forward, the
tracking must be adjusted.
1. Remove the 2 screws and tilt the seat to the side.
14 1813 - 001 - 11.05.2022
2. Loosen the lock screw (A) on the tracking controls.
A
B
3. Turn the tracking controls (B) counterclockwise until
they are fully open.
4. Adjust the tracking controls.
a) Turn the left tracking control 1 turn clockwise to
make the product turn to the left.
b) Turn the right tracking control 1 turn clockwise to
make the product turn to the right.
5. Tighten the lock screw on the tracking controls.
To replace the blade
WARNING: Use protective gloves. The
blades are very sharp.
WARNING: Make sure that the product
cannot start when you replace the blade.
1. Use the tool angle control to lift the tool holder from
the floor.
2. Loosen the screws on the tool holder.
3. Remove the blade.
4. Push the new blade into the tool holder.
5. Make sure that the blade is in the correct position.
6. Tighten the screws on the tool holder.
To install a chisel
WARNING: Use protective gloves. The
blades are very sharp.
WARNING: Make sure that the product
cannot start when you replace the blade.
1. Remove the blade. Refer to
To replace the blade on
page 15
.
2. Put the chisel (A) on the tool holder (B).
B
A
C
3. Install the washers and screws (C).
To sharpen the blade
WARNING: Use protective gloves. The
blades are very sharp.
1. Pull the tool angle handle rearward to raise the tool
holder from the floor.
2. Sharpen the blade with an angle grinder. Use a
grinding disc with a grit of 120.
WARNING: Make sure that the
grinding disc does not catch the edge or
corner of the blade.
1813 - 001 - 11.05.2022 15
a) Grind the top edge of the blade for bevel up.
b) Grind the bottom edge of the blade for bevel
down.
Battery maintenance
The batteries are maintenance free. Only let an
approved service center do servicing on the batteries if it
is necessary.
Hydraulic system
To do a check of the hydraulic hoses
Examine the hydraulic hoses regularly. Replace
worn or damaged hydraulic hoses.
WARNING: Hydraulic oil is dangerous.
The rubber in the hydraulic hoses wears with
time. Worn or damaged hydraulic hoses can
break and the hydraulic oil can cause injury.
If you cannot tell if the hydraulic hoses are
worn, always replace the hydraulic hoses.
To do a check of the hydraulic oil level
1. Read the hydraulic oil level on the hydraulic oil tank.
2. If the hydraulic oil level is too low, it is necessary to
replace the hydraulic oil. Refer to
To replace the oil
and oil filter on page 16
.
To read the state of charge
Note: Always keep the product connected to a mains
socket when it is not in operation. The firmware in the
charger will control the level of charge in the batteries.
CAUTION: Do not operate the product
while the charger is connected to a mains
socket. This will cause damage to the
charger.
1. Park the product in a safe area. Refer to
Work area
safety on page 6
.
2. Turn the ON/OFF key to the OFF position.
Note: The product do not charge when the
ON/OFF key is in the ON position.
3. Connect the charger and keep the charger
connected until the next time you use the product.
To replace the oil and oil filter
WARNING: Hydraulic oil is dangerous
to your skin. Clean spills with soap and
water.
WARNING: Used oil and filters are
dangerous to the environment. Discard used
chemicals at an applicable disposal location.
16 1813 - 001 - 11.05.2022
Note: It is faster to drain the hydraulic oil if the oil is
warm.
1. Remove the oil filter cover (A).
B
A
C
2. Put a container below the oil drain plug.
3. Remove the oil drain plug (B).
4. Turn the oil filter (C) counterclockwise to remove it.
5. Remove the oil cap (D).
ED
6. Lightly lubricate the rubber seal on the new oil filter
with new oil.
7. Attach the hydraulic oil filter. Tighten by hand until
there is resistance, then tighten ¾ turn more.
8. Install the oil drain plug when the hydraulic oil tank is
empty.
9. Fill the hydraulic tank until you can see the oil level
in the oil level indicator (E). Refer to
To do a check
of the hydraulic oil level on page 16
.
10. Install the oil cap.
1813 - 001 - 11.05.2022 17
Troubleshooting
Problem Cause Solution
The product does not
start.
The emergency stop button is engaged. Turn the emergency stop button on the con-
trol panel clockwise to disengage.
The thermal overload protector is engaged. Reset the thermal overload protector.
The product is not
easy to hold on to.
Defective component. Read the error code. Refer to
Error codes on
page 18
.
If you cannot solve the problem, speak to an
approved Husqvarna service agent.
Error codes
Blink frequency Cause Action
1 The batteries are not connected or
the battery voltage is too low.
Do a check of the battery connection.
Do a check of the charger connection.
Make sure that the batteries are not damaged.
2 Incorrect AC power input. Make sure that the AC input cord is connected between
the charger and the AC outlet.
Make sure that the power plug is correctly connected to
the mains.
3 To high temperature in the charger. The charger is to hot and have the entered protective
mode. Move the product to a location with a sufficient
airflow.
Disconnect the charger. Wait for 20 minutes and connect
the charger.
4 To high temperature in the battery. When the battery temperature is higher than the set val-
ue, the charger decrease the current or stop charge.
When the battery temperature drops, the charger start
automatically.
5 The output current is to high. Speak to an approved servicing dealer.
6 The battery voltage is to high. Make sure that the correct output battery voltage is con-
nected.
Transportation, storage and disposal
Transportation
WARNING: Be careful during
transportation. The product is heavy and can
cause injury or damage if it falls or moves
during transportation.
18 1813 - 001 - 11.05.2022
WARNING: Remove the tool before
transportation of the product.
CAUTION: Do not tow the product
behind a vehicle.
Lift the product to move it shorter distances. For
longer distances, put the product on a transportation
vehicle.
Put some type of protection on the product
during transportation. The protection keeps natural
elements such as rain and snow away from the
product.
To move the product up and down a
ramp
WARNING: Be very careful when you
move the product up and down ramps. The
product is heavy and there is a risk of injury
if the product falls or moves too quickly.
WARNING: For ramps with a steep
slope, always use a winch. Do not walk or
stay below or near the product.
To move the product down a ramp, operate the
product forward slowly.
To move the product up a ramp, operate the product
rearward slowly.
Do not turn the product to the left or to the right more
than 45° on a ramp.
To lift the product
WARNING: Make sure that the lifting
equipment has the correct specification to
lift the product safely. The type plate on the
product shows the product weight.
WARNING: Do not walk or stay below
or near a lifted product. Keep bystanders
away from the risk area. Refer to
Work area
safety on page 6
.
WARNING: Do not lift a damaged
product. Make sure that the lifting eyes are
correctly installed and not damaged.
1. Remove the tool.
2. Attach the lifting equipment at the lifting eyes (A).
A
3. Lift the product slowly.
4. To lift the product with a forklift, put the forklift blades
through the brackets (B).
B
B
To attach the product to a
transportation vehicle
1. Put wheel chocks at the wheels to prevent
movement during transportation.
2. Attach tie-down straps to the lifting eyes.
3. Attach and tighten the tie-down straps to the
transportation vehicle.
4. Make sure that the product cannot move.
Storage
CAUTION: Do not put the product in
storage outdoors. Always keep the product
indoors.
Keep the product in a dry and frost free area.
Clean the product and do a complete servicing
before you put the product in storage.
Keep the product in a locked area to prevent access
for children or persons that are not approved.
1813 - 001 - 11.05.2022 19
Connect the battery charger. Keep the battery
charger connected during storage.
If it is not possible to keep the battery charger
connected during the full storage period, do these
steps:
1. Make sure that the batteries are fully charged
before storage.
2. Pull the red handle to remove the connector.
3. Charge the product for 24 hours each 2–3
months.
Disposal
Obey the local recycling requirements and applicable
regulations.
Do not discard the battery as domestic waste.
When the product no longer is used, send it to
a Husqvarna dealer or discard it at a recycling
location.
Technical data
BMS220ADB
Dimensions
Lenght, mm 1700
Widht, mm 685
Height, mm 1350
Weight, kg 960–1080
Working widht, mm 50–686
Drive motor
Drive motor power, kW 4.0
Transmission
Max. speed, m/min 40
Operating conditions
Operating temperature, °C -5–+40
Relative humidity max, % 95
20 1813 - 001 - 11.05.2022
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100

Husqvarna BMS 220 ADB Manuel utilisateur

Taper
Manuel utilisateur