Ohaus V41PWE1501T Manuel utilisateur

Valor™ 4000W Series

Instruction Manual

Serie Valor™ 4000W

Manual de instrucciones

Série Valor™ 4000W

Manuel d’instructions

Valor™ 4000W Serie

Bedienungsanleitung

Serie Valor™ 4000W

Manuale di istruzioni

Valor™ 4000W Series EN-1

1. INTRODUCTION

This manual contains installation, operation and maintenance instructions for the

Valor™ 4000W Series. Please read the manual completely before using the scale.

1.1 Safety Precautions

Please follow these safety precautions:

 Verify that the AC Adapter input voltage matches the local AC power supply.

 Do not drop loads on the platform.

 Do not place the scale upside down on the platform.

 Disconnect the scale from power supply when cleaning.

 Operate the scale only under ambient conditions specified in these

instructions.

 Service should be performed only by authorized personnel.

 Only use weights within the scale’s capacity as specified in these instructions.

 Do not operate the scale in hostile environments.

 Do not carry the scale by the pan or sub-platform. Use the handholds on the

side of the scale housing.

2. INSTALLATION

2.1 Package Contents

 Scale

 Stainless Steel Pan

 Power Adapter & Plug

 Instruction Manual

 Warranty Card

 Capacity Label

2.2 Installing Components

Place the stainless steel pan onto the weighing platform before turning the scale on.

Figure 2-1. Install the Stainless Steel Pan onto the weighing platform

EN-2 Valor™ 4000W Series

2.3 Selecting the Location

Use the scale on a clean, firm and flat surface. Avoid locations with excessive air

current, vibrations, heat sources, or rapid temperature changes.

2.4 Leveling the Equipment

Adjust the leveling feet so the bubble is centered in the circle. Be sure the

equipment is level each time its location is changed.

Figure 2-2. Level Indicator

2.5 Power

The AC Adapter is used to power the scale when battery power is not needed.

First connect the AC Adapter plug to the scale input jack located at the bottom of

the scale according to the description below.

Figure 2-3. Slide to plug in

Then connect the AC adapter to the proper AC supply.

Figure 2-4. Connecting the AC adapter to AC supply

Caution: The scale can only be used in a dry environment when

powered by the AC adapter.

Level Bubble

Adjustable Feet

Valor™ 4000W Series EN-3

2.5.1 Battery Power:

The scale can be used on AC power immediately. Allow the battery to charge

for 12 hours before using the scale on battery power. The scale will

automatically switch to battery operation if there is a power failure or the power

cord is removed. With AC power, the scale is constantly charging, so the

battery charge indicator (see item 11 in table 3-2) will remain lit. The scale can

be operated during charging, and the battery is protected against overcharging.

For maximum operating time, the battery should be charged at room

temperature.

During battery operation, the battery symbol indicates the battery charging

status. When charging, the symbol will blink slowly and when fully charged the

symbol will stop blinking.

TABLE 2-1

Symbol

Charge Level

Battery in use:

Symbol displayed

Notes:

When battery symbol blinks fast, approximately 30 minutes working time is left.

When [Lo.bAt] is displayed, the scale will shut off.

Charging the scale must be performed in a dry environment.

CAUTION: Battery is to be replaced only by an authorized

OHAUS service dealer. Risk of explosion can occur if the

rechargeable battery is replaced with the wrong type or if it is

not properly connected. Dispose of the lead acid battery

according to local laws and regulations.

EN-4 Valor™ 4000W Series

3. OPERATION

3.1 Controls

Figure 3-1. Front Control Panel Valor 4000W with display

TABLE 3-1

Button

Functions

Short Press

1

(when on): Sets display to zero

Short Press (when off): Turns scale on

Long Press

2

(when on): Turns the scale off

Short Press (in Menu): Selects / accepts displayed setting

Short Press: Accumulates the weight or displays the

accumulated information at 0 load.

Long Press: Toggles through active Units

Short Press (in Menu): Toggles through available settings

Short Press: Initiates an application mode specific response

Long Press: Selects active Mode

Short Press (in Menu): returns to previous settings

Short Press: Enter / clear a Tare value

Long Press: Enters User Menu

Short Press (in Menu): Quickly exit User Menu

IR Sensor

3

can be programmed to act as “touchless” button.

See the User Menu section 4.3 for the available settings.

Notes:

1

Short Press: Press less than 2.5 seconds.

2

Long Press: Press and hold for more than 2.5 seconds.

3

The IR sensor can be activated by a hand or other object that is placed at a specified height (see

section 4.3) from the sensor. The sensor activation distance will vary based on the reflective nature

of the object. If unwanted activations occur due to unique situations the sensor can be turned off.

Valor™ 4000W Series EN-5

Display

TABLE 3-2 Display Symbols

Item

Description

Item

Description

1

NET symbol

9

Calibration / Menu Mode symbol

2

Center of Zero symbol

10

Dynamic symbol*

3

Negative symbol

11

Battery charge symbol

4

Stable weight symbol

12

Pound, Ounce, Pound:Ounce symbol

5

Preset Tare symbol*

13

Gram, Kilogram symbols

6

Pointer symbols

14

Pieces symbol*

7

IR Sensor symbol

15

Percent symbol

8

Accumulation symbol

Note: * Not Used

Figure 3-3. Valor 4000W Rear display.

The colored LED indicators on the right side of the control panels are used in

Checkweigh mode (section 3.6) and will light up according to the following rules:

(Red) Loads > Upper limit

(Green) Loads ≥ Lower limit and ≤ Upper limit

(Yellow) Loads < Lower limit

1

IR Sensor

Figure 3-2. Valor 4000W Display

1

2

1

3

1

4

1

5

1

6

1

7

1

8

1

9

1

10

1

11

1

12

1

13

1

14

1

15

LED Indicators

EN-6 Valor™ 4000W Series

3.2 Turning Scale On/Off

To turn the scale on, press the On/Zero Off button. The scale performs a display

test, momentarily displays the software version, and then enters the active weighing

mode.

To turn the scale off, press and hold the On/Zero Off button until OFF is displayed.

3.3 Initial Calibration

When the scale is first installed it should be calibrated to ensure accurate results.

Before performing the calibration, be sure to have the appropriate calibration

weights as listed in table 3-3.

Press and hold Menu until [mMeNU] (Menu) is displayed. When the button is released,

the display will display [C.A.L]. Press Yes to accept, [SpaN] will then be shown. Press

Yes again to begin the span calibration. [--C--] blinks while zero reading is stored.

Next, the display shows the calibration weight value. Place the specified calibration

mass on the pan and press Yes. [--C--] blinks while the reading is stored. The scale

returns to the previous application mode and is ready for use.

The message [Err 3.0 CAl] will be displayed if these calibration steps were not

followed or if the wrong weight was used.

The calibration process can be aborted by turning the scale off.

TABLE 3-3

Required Span Calibration Mass (sold separately)

Max

Mass

1

Max

Mass

1

1500g

1.5kg / 3lb

6000g

6kg / 15lb

3000g

3kg / 6lb

15000g

15kg / 30lb

Note:

1

Pound masses are used when calibrating in the lb unit.

3.4 Weigh Mode

1. Press and hold Mode until [wJeIGH] (Weigh) is displayed.

2. If required, place an empty container on the pan and press Tare.

3. Add sample to the pan or container. The display shows the weight of the

sample.

Valor™ 4000W Series EN-7

3.5 Percent Mode

This mode measures the weight of a sample as a percentage of a reference weight.

1. Press and hold Mode until [PerCNt] is displayed. [Clr.ref] (clear reference) will

then display.

Notes: Press Function to view the current reference weight.

If there is no reference data stored, [Set.ref] is displayed. Press Yes to

set reference data.

2. Press No to use the stored reference weight and proceed to step 6.

3. If required, place an empty container on the pan and press Tare. Press Yes to

establish a new reference. Scale will now display [PUt.ref].

4. Add the desired reference material to the container. Press Yes to store the

reference weight. The display shows 100%.

5. Remove the reference material. If required, place an empty container on the

pan and press Tare.

6. Add the sample material. The display shows the percentage of the sample

compared to reference weight.

7. To clear the stored reference data press and hold Mode until [PerCNt] is

displayed. Press Yes when [Clr.ref] is displayed.

3.6 Checkweigh Mode

This mode sets low and high weight limits for portion control processes.

1. Press and hold Mode until [CHeCk] (Check) is displayed. [CLr.ref] (clear

references) will then display.

Notes: Press Function to view the low and high reference weight limits.

If there is no reference data stored, [Set.ref] is displayed. Press Yes to

set reference data.

2. Press No to use the stored reference weight limits and proceed to step 5.

3. Press Yes to establish new reference values. The scale will then display [Set.

LO]. Press Yes to view the “Low” limit value. Press Yes to accept or No to edit

the “Low” limit value. The stored value then displays with the first digit

highlighted [000.000 kg]. Repeatedly press No until the desired number

appears. Press Yes to accept and highlight the next digit. Repeat until all the

digits are correct. Press Yes to accept the “low” limit value, [Set. HI] will be

displayed.

4. Repeat the same procedure to accept or edit the “high” value.

5. If required, place an empty container on the pan and press Tare. Place

sample material on the pan or in the container. If the sample weight is under

the target weight range, the yellow LED will light. If the sample is within the

target weight range, the green LED will light. If the sample is over the target

weight range, the red LED will light.

6. To clear the stored reference values press and hold Mode until [CHeCk] is

displayed. Press Yes when [Clr.ref] is displayed.

EN-8 Valor™ 4000W Series

3.7 Accumulation

Accumulation works together with each application mode. This function allows the

user to store the total of a series of weight measurements.

1. Press the M+ key to add the weight to the accumulation data. The Σ icon will

keep flashing until the weight is removed.

Note: When Accumulate is set to AUTO in the setup menu, it is not

necessary to press the M+ key.

2. When the pan is cleared, press the M+ key to display the statistical information

of the accumulation data.

3. To clear the accumulation data press the Tare key when the display is

showing the statistical information of the accumulation data. The display

shows [Clr.aCC]. Press the Yes key to clear the stored data and return to

current mode.

Notes:

Only stable weights are stored to accumulation total.

To prevent the same load from being added to the total multiple times, the load on

the pan must be returned to 0 before the next load can be added.

When Legal for Trade is OFF, the display must return to 0 gross, 0 net or a negative

net value; when Legal for Trade is ON, the display must return to 0 gross.

Otherwise, the Σ icon will continue flashing.

Gross loads and net loads cannot be added to the same total. If the first load is a

gross weight, future loads must also be gross weights. If the first load is a net

weight, future loads must also be net weights.

The max of accumulation times is 9999.

Changing the mode will clear the accumulation data.

Accumulation Example:

In weighing mode; sub menu ACCUmM setting, select mMaNU:

If required, place an empty container on the pan and press

Tare.

Step i. Put the weight (0.04 kg) on the pan and press M+

key. The Σ icon indicator will keep flashing until

the weight is removed.

Step ii. Remove the weight from the pan. Put another

weight (0.03 kg) and press M+ key:

Step iii. Remove the weight from the pan:

Step iv. Press M+ key to display the statistical information:

Step v. If required, follow step 3 above to clear the

accumulation data.

N 2

tOtal

0.070 kg

mMIN

0.030 kg

mMax

0.040 kg

mMaNU

*

0.040 kg

*

0.030 kg

*

0.000 kg

Valor™ 4000W Series EN-9

4. MENU SETTINGS

The User Menu allows the customizing of scale settings.

4.1 Menu Navigation

User Menu:

Menu:

C.A.L

S.E.t.U.P

r.E.A.d

M.O.d.E

U.n.i.t

L.O.C.k

E.n.d

Menu

Items:

Span

Lin

GEO

End

Reset

Pwr.Un

A.Tare

Ir.Func

Ir.Adj

Accum

End

Reset

Stable

Filter

AZT

Light

Sleep

A.Off

End

Reset

Percnt

Check

End

kg

g

oz

lb

lb:oz

End

Reset

L.Cal

L.Setup

L.Read

L.Mode

L.Unit

End

Notes:

Some Units/Modes may not be available in all models.

When LEGAL FOR TRADE is set to ON (see section 4.9), the menu settings are

affected.

To Enter the Menu Mode

Press and hold Menu until [mMeNU] (Menu) is displayed. When released the first sub-

menu [C.a.l] (Cal) will be shown.

Press Yes to enter the displayed sub-menu or press No to advance to the next.

Selecting a sub-menu will display the first menu item. Press Yes to view the menu

item setting or press No to move to the next menu item. When viewing the setting,

press Yes to accept the setting, or press No to change the setting. When [End] is

displayed, press Yes to return to the sub-menu selections or No to return to the first

item in the current menu. Bold indicates factory default setting.

Note: The Calibration / Menu Mode indicator is displayed when in the Menu Mode.

4.2 Cal Menu

Enter this menu to perform calibrations.

 Span [SpaN] (yes, no)

Initiates a span calibration procedure (zero and span).

 Lin [LIN] (yes, no)

Initiates a linearity calibration procedure (zero, mid-point and span).

 GEO [GEO]

Geographical Adjustment Factor (GEO) is used to adjust the calibration

based on the current location. Settings from 0 to 31 are available with 12

being the default. Refer to table 4-1 to determine the GEO factor that

corresponds to your location.

 End Cal [End]

Advance to the next menu or return to the top of the current menu.

EN-10 Valor™ 4000W Series

4.3 Setup Menu

Enter this menu to set scale parameters.

 Reset [reset] (no, yes)

Reset the Setup menu to factory defaults.

 Power on unit [pwWr.UN] (auto, kg, g, lb, oz, lb:oz)

Set the unit of measure displayed at startup

 Auto Tare [A.tArE] (off, on, on-acc)

Set the automatic tare functionality. If “on” is selected the first stable gross

weight is tared. If “on-acc” is selected, stable gross loads within the accept

limits are tared (in Checkweigh mode)

 IR Function [Ir.FUNC] (off, tare)

Set the IR sensor functionality.

 IR Adj [Ir.adj] (hi, low)

Set the detecting level for the IR sensor.

(For reference: Hi: ~ 100 mm / 4 inches; Low: ~ 50mm / 2 inches)

 Accumulation [aCCUmM] (off, auto, manu)

Set the accumulation functionality.

 End Setup [End]

Advance to the next menu or return to the top of the current menu.

4.4 Read Menu

Enter this menu to set user preferences.

 Reset [reset] (no, yes)

Reset the Read menu to factory defaults.

 Stable Range [Stable] (0.5, 1, 2, 5)

Set the amount the reading can vary while the stability symbol remains on.

 Filter [FILtEr] (low, medium, high)

Set the amount of signal filtering.

 Auto-Zero Tracking [AZt] (off, 0.5, 1, 3)

Set the automatic zero tracking functionality.

 Light [LIGHt] (hi, med, low)

Sets backlight functionality.

 Sleep [SLEEP] (off, on)

Set the display shut off time.

 Auto off [A.OFF] (off, 1, 5, 10)

Set the automatic shut off functionality.

 End Readout [End]

Advance to the next menu or return to the top of the current menu.

Valor™ 4000W Series EN-11

4.5 Mode Menu

Enter this menu to activate modes so they will be available for use with the Mode

button. Weigh mode is always active by default.

 Reset [reset] (no, yes)

Reset the Mode menu to factory defaults.

 Percent [PerCNt] (off, on)

Set the status.

 Check [CHECk] (off, on)

Set the sub-mode.

 End Mode [End]

Advance to the next menu or return to the top of the current menu.

4.6 Unit Menu

Enter this menu to activate units so they will be accessible with the Units button.

The units in the menu must be turned “on” to be active.

Note: Available units vary by model and local regulations.

4.7 Lock Menu

The Lock Menu is a software controlled option which can lock Menu settings to

prevent tampering.

 Reset [reset] (no, yes)

Reset the Lock menu to factory defaults.

 Lock Cal [l.CAL] (off, on)

Set the status.

 Lock Setup [l.SEtUP] (off, on)

Set the status.

 Lock Read [l.rEAD] (off, on)

Set the status.

 Lock Mode [l.mMOdE] (off, on)

Set the status.

 Lock Unit [l.UNIt] (off, on)

Set the status.

 End Lock [End]

Advance to the next menu or return to the top of the current menu.

4.8 End Menu

Press ‘Yes’ to advance to the Calibration menu. Press ‘No’ to exit the menu and

return to the current application mode.

EN-12 Valor™ 4000W Series

TABLE 4-1. GEO CODES

0 325 650 975 1300 1625 1950 2275 2600 2925 3250

325 650 975 1300 1625 1950 2275 2600 2925 3250 3575

0 1060 2130 3200 4260 5330 6400 7460 8530 9600 10660

1060 2130 3200 4260 5330 6400 7460 8530 9600 10660 11730

0°00' 5°46' 5 4 4 3 3 2 2 1 1 0 0

5°46' 9°52' 5 5 4 4 3 3 2 2 1 1 0

9°52' 12°44' 6 5 5 4 4 3 3 2 2 1 1

12°44' 15°06' 6 6 5 5 4 4 3 3 2 2 1

15°06' 17°10' 7 6 6 5 5 4 4 3 3 2 2

17°10' 19°02' 7 7 6 6 5 5 4 4 3 3 2

19°02' 20°45' 8 7 7 6 6 5 5 4 4 3 3

20°45' 22°22' 8 8 7 7 6 6 5 5 4 4 3

22°22' 23°54' 9 8 8 7 7 6 6 5 5 4 4

23°54' 25°21' 9 9 8 8 7 7 6 6 5 5 4

25°21' 26°45' 10 9 9 8 8 7 7 6 6 5 5

26°45' 28°06' 10 10 9 9 8 8 7 7 6 6 5

28°06' 29°25' 11 10 10 9 9 8 8 7 7 6 6

29°25' 30°41' 11 11 10 10 9 9 8 8 7 7 6

30°41' 31°56' 12 11 11 10 10 9 9 8 8 7 7

31°56' 33°09' 12 12 11 11 10 10 9 9 8 8 7

33°09' 34°21' 13 12 12 11 11 10 10 9 9 8 8

34°21' 35°31' 13 13 12 12 11 11 10 10 9 9 8

35°31' 36°41' 14 13 13 12 12 11 11 10 10 9 9

36°41' 37°50' 14 14 13 13 12 12 11 11 10 10 9

37°50' 38°58' 15 14 14 13 13 12 12 11 11 10 10

38°58' 40°05' 15 15 14 14 13 13 12 12 11 11 10

40°05' 41°12' 16 15 15 14 14 13 13 12 12 11 11

41°12' 42°19' 16 16 15 15 14 14 13 13 12 12 11

42°19' 43°26' 17 16 16 15 15 14 14 13 13 12 12

43°26' 44°32' 17 17 16 16 15 15 14 14 13 13 12

44°32' 45°38' 18 17 17 16 16 15 15 14 14 13 13

45°38' 46°45' 18 18 17 17 16 16 15 15 14 14 13

46°45' 47°51' 19 18 18 17 17 16 16 15 15 14 14

47°51' 48°58' 19 19 18 18 17 17 16 16 15 15 14

48°58' 50°06' 20 19 19 18 18 17 17 16 16 15 15

50°06' 51°13' 20 20 19 19 18 18 17 17 16 16 15

51°13' 52°22' 21 20 20 19 19 18 18 17 17 16 16

52°22' 53°31' 21 21 20 20 19 19 18 18 17 17 16

53°31' 54°41' 22 21 21 20 20 19 19 18 18 17 17

54°41' 55°52' 22 22 21 21 20 20 19 19 18 18 17

55°52' 57°04' 23 22 22 21 21 20 20 19 19 18 18

57°04' 58°17' 23 23 22 22 21 21 20 20 19 19 18

58°17' 59°32' 24 23 23 22 22 21 21 20 20 19 19

59°32' 60°49' 24 24 23 23 22 22 21 21 20 20 19

60°49' 62°90' 25 24 24 23 23 22 22 21 21 20 20

62°90' 63°30' 25 25 24 24 23 23 22 22 21 21 20

63°30' 64°55' 26 25 25 24 24 23 23 22 22 21 21

64°55' 66°24' 26 26 25 25 24 24 23 23 22 22 21

66°24' 67°57' 27 26 26 25 25 24 24 23 23 22 22

67°57' 69°35' 27 27 26 26 25 25 24 24 23 23 22

69°35' 71°21' 28 27 27 26 26 25 25 24 24 23 23

71°21' 73°16' 28 28 27 27 26 26 25 25 24 24 23

73°16' 75°24' 29 28 28 27 27 26 26 25 25 24 24

75°24' 77°52' 29 29 28 28 27 27 26 26 25 25 24

77°52' 80°56' 30 29 29 28 28 27 27 26 26 25 25

80°56' 85°45' 30 30 29 29 28 28 27 27 26 26 25

85°45' 90°00' 31 30 30 29 29 28 28 27 27 26 26

Elevation in meters

Elevation in feet

GEO value

Latitude

Valor™ 4000W Series EN-13

4.9 Legal For Trade

When the scale is used in trade or a legally controlled application it must be set up,

verified and sealed in accordance with local weights and measures regulations. It is

the responsibility of the purchaser to ensure that all pertinent legal requirements are

met.

4.9.1 Capacity Label

A label showing the capacity and readability of the scale must be installed near

each display. If the Capacity Labels were installed prior to delivery, no further action

is needed. If the Capacity Labels were not installed, they have been placed in the

packaging material. Affix the labels above the displays as shown in Figure 4-1.

Note: The Capacity Labels will be destroyed upon removal, so only attempt to

install them once.

Figure 4-1. Front and rear display capacity label locations

4.9.2 Settings

Before verification and sealing, perform the following steps:

1. Set Legal For Trade to OFF.

2. Verify that the menu settings meet the local weights and measures regulations.

3. Perform a calibration as explained in Section 3.3.

4. Set Legal For Trade to ON.

To change the scale’s Legal For Trade (LFT) setting, follow this procedure:

Caution: When accessing the bottom of the scale, avoid placing the scale

upside down on the pan or sub-platform. Place the scale on its side.

1. Turn the scale OFF.

2. Remove the Security Cover under the scale to access

the two pins located in a slot (see figure 4-2). Short these

pins (a slotted screwdriver may be used), while powering

the scale ON. The scale will perform the start-up

procedure, and then the display will show the current

status [lft OFF] (LFT OFF, unlocked) or [lft ON] (LFT

ON, locked); press the ‘No’ key to change this setting, or

press the ‘Yes’ key to confirm it.

Note: When Legal For Trade is set to On, the menu settings are affected as follows:

Calibration (C.A.L) menu is not accessible

IR Function, Filter and Unit menus are locked at the current settings.

Stable Range setting is locked at 1d

Auto-Zero Tracking setting is locked at 0.5d

3. Replace the Security Cover.

Capacity Label

Figure 4-2. LFT pins.

EN-14 Valor™ 4000W Series

4.9.3 Verification and Sealing

The local weights and measures official or authorized service agent must perform

the verification procedure.

4.9.3.1 Physical Seals

For jurisdictions that use the physical sealing method, the local weights and

measures official or authorized service agent must apply a security seal to prevent

tampering with the settings. Refer to the illustrations below for sealing methods.

Unlocked Locked

Figure 4-3. Sealing

4.9.3.2 Audit Trail Seal (USA and Canada only)

For jurisdictions that use the audit trail sealing method, the local weights and

measures official or authorized service agent must record the current configuration

and calibration event counter values at the time of sealing. These values will be

compared to values found during a future inspection.

Note: A change to an event counter value is equivalent to breaking a physical seal.

The audit trail uses two event counters to record changes to configuration and

calibration settings.

 The configuration event counter (CFG) will index by 1 under the following

conditions:

- When the LFT setting is changed from ON to OFF.

- When exiting the menu if one or more of the following menu settings

are changed: Stable Range, Auto Zero Tracking (AZT), Filter, IR

Function and Units (kg, g, oz, lb or lb:oz).

 The calibration event counter (CAL) will index by 1 when exiting the menu

if a Span Calibration or GEO setting change is made.

Note: The counter only indexes once, even if several settings are changed.

The event counters can be viewed by pressing and holding the MENU button.

While the button is held, the display will show MENU followed by Audit.

Release the button when Audit is displayed to view the audit trail information.

Wire Seal

Paper Seal

Security Cover

Valor™ 4000W Series EN-15

The audit trail information is displayed in the format CFGxxx and CALxxx.

The scale then returns to normal operation.

5. MAINTENANCE

5.1 Cleaning

The housing may be cleaned with a cloth dampened with a mild detergent if

necessary. Do not use solvents, chemicals, alcohol, ammonia or abrasives to clean

the housing or control panels.

5.2 Cleaning the Plastic Pan

5.2.1 Uninstalling and cleaning the plastic pan

Please follow the steps below to clean the plastic pan:

1. Remove the stainless steel pan

2. Remove the four thumb screws holding the battery cover.

3. Unplug the two battery clips and remove the battery.

4. Using a Phillips screwdriver, remove the two screws located at the bottom of the

battery compartment.

5. Remove the plastic pan.

6. Clean the plastic pan.

6

3

1

2

4

5

Figure 5-1. Pan cleaning

5.2.2 Reinstalling the pan after cleaning

Please follow the steps below to reinstall the plastic pan (see also the steps in figure

5-1, in reversed order):

1. Using a Phillips screwdriver, attach the plastic pan to the housing with the

two screws.

2. Place the battery in the battery compartment and attach the two battery clips.

Attach the red wire to the positive (red) battery terminal and the black wire to

the negative (black) battery terminal.

3. Attach the battery cover with the four thumb screws.

4. Place the scale upright and install the stainless steel pan.

Caution: Risk of explosion can occur if the battery is not properly

connected.

EN-16 Valor™ 4000W Series

5.3 Troubleshooting

The following table lists common problems and possible causes and remedies.

If the problem persists, contact OHAUS or your authorized dealer.

TABLE 5-1

Symptom

Possible Cause

Remedy

Cannot turn on

No power to scale

Battery discharged

Verify connections, power source

and battery charge status.

Poor accuracy

Improper calibration

Unstable environment

Perform calibration

Move scale to suitable location

Cannot calibrate

Unstable environment

Incorrect calibration weight

Move the scale to suitable location

Use correct calibration weight

Cannot access mode

Mode not enabled

Enter menu and enable mode

Cannot access unit

Unit not enabled

Enter menu and enable unit

LO ref

Reference weight is too low

Increase reference weight.

Err 3.0 Cal

Incorrect calibration weight

See table 3-3 for correct weights

Err 8.1 ˉLOadˉ

Power on zero range exceeded

Clear pan

Err 8.2 _LOad_

Power on zero under range

Install pan

Err 8.3 ˉLOadˉ

Overload

Load exceeds scale maximum

capacity

Err 8.4 _LOad_

Under load

Reading below min. range - Re-

install pan.

Err 8.5 ˉtareˉ

Tare out of range

Tare value exceeds maximum.

Err 9 Data

Internal data error.

Contact an authorized service agent

Err13 mMEmM

Fail to write EEPROM.

Contact an authorized service agent

Err 53 C.SUmM

Invalid checksum data

Contact an authorized service agent

Lo.Bat

Battery is discharged

Connect the power and charge the

battery

NO.ACC

Gross and net weights cannot be

accumulated together

Accumulate only gross or net

weights.

Battery fails to charge

fully

Battery is defective

Have battery replaced by OHAUS

authorized service dealer.

5.4 Service Information

If the troubleshooting section does not resolve or describe your problem, contact

your authorized OHAUS service agent. Please visit our web site, www.ohaus.com

to locate the OHAUS office nearest you. An OHAUS product service specialist will

be available to provide assistance.

6. TECHNICAL DATA

The technical data is valid under the following ambient conditions:

Indoor use only

Operating temperature: -10ºC (14ºF) to 40ºC (104ºF)

Relative humidity: 10% to 90% relative humidity, non-condensing

Altitude: Up to 2000 m

Power: AC Adapter (supplied) - 12 VDC 0.84 A output, internal rechargeable sealed

lead-acid battery

Mains supply voltage fluctuations: up to ±10% of the nominal voltage

Installation Category: II

Pollution Degree: 2

Valor™ 4000W Series EN-17

6.1 Specifications

TABLE 6-1

MODEL

V41PWE1501T

V41XWE1501T

V41PWE3T

V41XWE3T

V41PWE6T

V41XWE6T

V41PWE15T

V41XWE15T

Capacity x Readability

(Max x d non-approved)

1.5 kg x 0.0002 kg

1500 g x 0.2 g

3 lb x 0.0005 lb

48 oz x 0.01 oz

3 kg x 0.0005 kg

3000 g x 0.5 g

6 lb x 0.001 lb

96 oz x 0.02 oz

6 kg x 0.001 kg

6000 g x 1 g

15 lb x 0.002 lb

240 oz x 0.05 oz

15 kg x 0.002 kg

15000 g x 2 g

30 lb x 0.005 lb

480 oz x 0.1 oz

Maximum Displayed Resolution

7500

6000

7500

Capacity X Readability

(Max x e approved)

1.5 kg x 0.0005 kg

1500 g x 0.5 g

3 lb x 0.001 lb

48 oz x 0.02 oz

3 kg x 0.001 kg

3000 g x 1 g

6 lb x 0.002 lb

96 oz x 0.05 oz

6 kg x 0.002 kg

6000 g x 2 g

15 lb x 0.005 lb

240 oz x 0.1 oz

15 kg x 0.005 kg

15000 g x 5 g

30 lb x 0.01 lb

480 oz x 0.2 oz

Approved Resolution

3000

Repeatability

0.0005 kg

0.001 kg

0.002 kg

0.005 kg

Linearity

± 0.0005kg

± 0.001kg

± 0.002kg

± 0.005kg

Weighing Units*

Non-Approved models: g, kg, lb, oz, lb:oz

EC and OIML Approved models: g, kg

Measurement Canada and NTEP Approved models: g, kg, lb, oz

Tare Range

To capacity by subtraction

Stabilization Time

≤ 0.5 seconds

Safe Overload Protection

150 % of scale capacity

Weight Display

2 x Red LED (front and rear)

6-digit 7-segment, 20.5 mm / 0.8 in characters

Keyboard

Four buttons

Application Modes

Weighing, Percent, Check Weighing (each with Accumulate function)

Battery Operating Time (at 20ºC)

Typically 50 hours with 12-hour full charge

Construction

V41PW: ABS housing with 304 Stainless Steel Platform

V41XW: ABS bottom housing with 304 stainless steel top housing and platform

Ingress Protection

IPX8

Pan Dimensions

190 x 242 mm / 7.5 x 9.5 in

Approval Class

III

Net Weight

V41PW: 3.0 kg / 6.6 lb; V41XW: 3.9 kg / 8.6 lb

Shipping Weight

V41PW: 4.0 kg / 8.8 lb; V41XW: 4.9 kg / 10.8 lb

Shipping Dimensions

410 x 370 x 220 mm / 16.1 x 14.6 x 8.7 in

Note: Turn off lb:oz unit with LFT ON

6.2 Drawings and Dimensions

V41PW

A

256 mm / 10.1 in.

B

280 mm / 11.0 in.

C

121 mm / 4.8 in.

V41XW

A

256 mm / 10.1 in.

B

288 mm / 11.3 in.

C

124 mm / 4.9 in.

A

C

B

TABLE 6-2

Figure 6-1. Dimensions

EN-18 Valor™ 4000W Series

6.3 Compliance

Compliance to the following standards is indicated by the corresponding mark on

the product.

Mark

Standard

This product conforms to the EMC Directive 2004/108/EC, the Low

Voltage Directive 2006/95/EC and the Non-Automatic Weighing

Instrument Directive 2009/23/EC. The Declaration of Conformity is

available online at

europe.ohaus.com/europe/en/home/support/compliance.aspx.

AS/NZS CISPR 11

CAN/CSA-C22.2 No. 61010-1-12

UL Std. No. 61010-1 (3

rd

edition)

NSF/ANSI 169–2009

NSF/ANSI/3-A 14159-1-2010

Important notice for verified weighing instruments

Weighing Instruments verified at the place of manufacture bear one

of the preceding marks on the packing label and the green ‘M’

(metrology) sticker on the descriptive data plate. They may be put into

service immediately.

Weighing Instruments to be verified in two stages have no green ‘M’

(metrology) on the descriptive data plate and bear one of the

preceding identification marks on the packing label. The second

stage of the initial verification must be carried out by an authorized

and certified service organization established within the European

Community or by the National Notified Body.

The first stage of the initial verification has been carried out at the manufacturers

work. It comprises all tests according to the adopted European standard EN

45501:1992, paragraph 8.2.2.

If national regulations limit the validity period of the verification, the user of the

weighing instrument must strictly observe the re-verification period and inform the

respective weights and measures authorities.

La page charge ...

Ohaus V41PWE1501T Manuel utilisateur

Ce manuel convient également à

Ohaus V41PWE1501T Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents