Samsung DVD-P380 Manuel utilisateur

Catégorie
Lecteurs DVD
Taper
Manuel utilisateur
DVD Player
DVD-P380
CA
CA
AK68-01509V
www.samsung.com/ca
ENG-2
Important Safety Instructions
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings, Install in accordance with the manufacturer's instructions.
8) Do not install near any heat sources such as radiators, heat registers,stoves, or other apparatus (including
amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized or grounding- type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug has two blades and a third grounding prong.
The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your
outlet, consult an electrician for replacement of the obsolete outlet.
10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus.
11) Only use attachments/accessories specified by the manufacturer.
12) Use only with cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the apparatus. When a cart is used, use caution when
moving the cart/apparatus combination to avoid injury from tip-over.
13) Unplug this apparatus during lightning storms or when unused for long peroids of
time.
14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been
damaged in any way, such as the power-supply cord or plug is damaged, liquid has been spilled or objects
have fallen into the apparatus. Service is also required if the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped.
ENG-3
Precautions
This symbol indicates that
dangerous voltage consisting a risk
of electric shock is present within
this unit.
This symbol indicates that there are
important operating and
maintenance instructions in the
literature accompanying this unit.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
Do not install this equipment in a confined space such as a bookcase or similar unit.
WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS
APPARATUS TO RAIN OR MOISTURE.
FCC NOTE (for U.S.A):
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and on.
The user is encouraged to try to correct the interference by one or more of the following measures.
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect this equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This class B digital apparatus meets all requirements of the Canadian Interference --
Causing Equipment Regulations.
CLASS 1 LASER PRODUCT
KLASSE 1 LASER PRODUKT
LUOKAN 1 LASER LAITE
KLASS 1 LASER APPARAT
PRODUCTO LÁSER CLASE 1
Note to CATV system installer : This reminder is provided to call CATV system installer’s attention to
Article 820-40 of the National Electrical Code (Section 54 of Canadian Electrical Code, Part I) that
provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be
connected to the grounding system of the building as close to the point of cable entry as practical.
This product satisfies FCC regulations when shielded cables and connectors are used to connect the
unit to other equipment. To prevent electromagnetic interference with electric appliances, such as radios
and televisions, use shielded cables and connectors for connections.
Caution : FCC regulations state that any unauthorized changes or modifications to this equipment may
void the user’s authority to operate it.
CALIFORNIA USA ONLY :
This Perchlorate warning applies only to primary CR (Maganese Dioxide) Lithium coin cells in the product sold
or distributed ONLY in California USA “Perchlorate Material - special handling may apply , See
www.dtsc.ca.gov/hazardouswaste/perchlorate.
ENG-4
CAUTION
THIS PRODUCT UTILIZES A LASER. USE OF CONTROLS OR ADJUSTMENTS OR
PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN
HAZARDOUS RADIATION EXPOSURE. DO NOT OPEN COVER AND DO NOT REPAIR
YOURSELF. REFER SERVICING TO QUALIFIED PERSONNEL.
Note:
This unit can be used only where the power supply is AC 120V, 60Hz. It cannot be used elsewhere.
This DVD player is designed and manufactured to respond to the Region Management Information.
If the Region number of a DVD disc does not correspond to the Region number of this DVD player,
the DVD player cannot play the disc.
The product unit accompanying this user manual is licensed under certain intellectual property rights
of certain third parties. In particular, this product is licensed under the following US patents:
5,457,669 5,561,649 5,705,762 5,987,417 6,043,912 6,222,983 6,272,096 6,377,524
6,377,531 6,385,587 6,389,570 6,408,408 6,466,532 6,473,736 6,477,501 6,480,829 6,556,520
6,556,521 6,556,522 6,578,163 6,594,208 6,631,110 6,658,588 6,674,697 6,674,957 6,687,455
6,697,307 6,707,985 6,721,243 6,721,493 6,728,474 6,741,535 6,744,713 6,744,972 6,765,853
6,765,853 6,771,890 6,771,891 6 775,465 6,778,755 6,788,629 6,788,630 6,795,637 6,810,201
6,862,256 6,868,054 6,894,963 6,937,552.
This license is limited to private non-commercial use by end-user consumers for licensed contents.
No rights are granted for commercial use. The license does not cover any product unit other than this
product unit and the license does not extend to any unlicensed product unit or process conforming to
ISO/IEC 11172-3 or ISO/IEC 13818-3 used or sold in combination with this product unit.
The license only covers the use of this product unit to encode and/or decode audio files conforming
to the ISO/IEC 11172-3 or ISO/IEC 13818-3. No rights are granted under this license for product
features or functions that do not conform to the ISO/IEC 11172-3 or ISO/IEC 13818-3.
Handling Cautions
Before connecting other components to this player, be sure to turn them all off.
• Do not move the player while a disc is being played, or the disc may be scratched or broken, and the player’s
internal parts may be damaged.
• Do not put a flower vase filled with water or any small metal objects on the player.
• Be careful not to put your hand into the disc tray.
• Do not place anything other than the disc in the disc tray.
• Exterior interference such as lightning and static electricity can affect normal operation of this player.
If this occurs, turn the player off and on again with the POWER button, or disconnect and then reconnect the
AC power cord to the AC power outlet. The player will operate normally.
• Be sure to remove the disc and turn off the player after use.
• Disconnect the AC power cord from the AC outlet when you don’t intend to use the player for long
periods of time.
• Clean the disc by wiping in a straight line from the inside to the outside of the disc.
The Main plug is used as a disconnect device and shall stay readily operable at any time.
Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases,
shall be placed on the apparatus.
Disc Storage
Be careful not to harm the disc because the data on these discs is highly vulnerable to the environment.
• Do not keep under direct sunlight.
• Keep in a cool ventilated area.
• Store vertically.
• Keep in a clean protection jacket.
Maintenance of Cabinet
For safety reasons, be sure to disconnect the AC power cord from the AC outlet.
• Do not use benzene, thinner, or other solvents for cleaning.
• Wipe the cabinet with a soft cloth.
Install Batteries in the Remote control
1
Open the battery
cover on the back of
the remote control.
2
Insert two AAA batteries.
Make sure that the
polarities (+ and -) are
aligned correctly.
3
Replace the battery
cover.
If the remote control doesn’t operate properly:
- Check the polarity + - of the batteries.
- Check if the batteries are drained.
- Check if the remote control sensor is blocked by obstacles.
- Check if there is any fluorescent lighting nearby.
Before you start
Accessories
ENG-5
Remote
Control
Batteries for
Remote Control
(AAA Size)
User’s Manual Video/Audio
Cable
ENG-6
TABLE OF CONTENTS
Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Before you start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Chapter 1:
Setup
General Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Disc Type and Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Tour of the Remote Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Chapter 2: Connections
Choosing a connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Chapter 3: Basic Functions
Playing a Disc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Using the Search and Skip Functions . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Using the Display Function. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Using the Disc and Title Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Repeat Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Slow Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Chapter 4: Advanced Functions
Adjusting the Aspect Ratio (EZ View). . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Selecting the Audio Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Selecting the Subtitle Language. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Changing the Camera Angle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Using the Bookmark Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Using the Zoom Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Clips Menu for MP3/WMA/JPEG/MPEG4/CD Audio . . . . . . . . . . . . . . . 32
Folder Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
MP3/WMA/CD Audio Playback. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
MPEG4 Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Playing Media Files Using the USB Host Feature . . . . . . . . . . . . . . . . . 37
CD Ripping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Picture CD Playback. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Chapter 5: Navigating the Setup Menu
Using the Setup Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Setting Up the Language Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Setting Up the Audio Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Setting Up the Display Options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Setting Up the Parental Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Chapter 6: Reference
Firmware Upgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
USB Host Feature Supported Products . . . . . . . . . . . . . . . . . . . . . . . . . 55
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
ENG-7
Chapter 1
SETUP
Setup
General Features
Excellent Sound
Dolby Digital, a technology developed by Dolby
Laboratories, provides crystal clear sound
reproduction.
Screen
Both regular and widescreen(16:9) pictures can be
viewed.
Slow Motion
An important scene can be viewed in slow motion.
Parental Control (DVD)
The parental control allows users to set the level
necessary to prohibit children from viewing harmful
movies such as those with violence, adult subject
matter, etc.
Various On-Screen Menu Functions
You can select various languages (Audio/Subtitle)
and screen angles while enjoying movies.
Progressive Scan
Progressive scanning creates an improved picture
with double the scan lines of a conventional
interlaced picture.
EZ VIEW (DVD)
Easy View enables picture adjustment to match your
TV's screen size (16:9 or 4:3).
Digital Photo Viewer (JPEG)
You can view Digital Photos on your TV.
Repeat
You can repeat a song or movie simply by pressing
the REPEAT button.
MP3/WMA
This unit can play discs created from MP3/WMA files.
MPEG4
This unit can play MPEG4 formats within an avi file.
CD Ripping
This feature lets you to copy audio files from Audio
CDs to a USB device in the MP3 format.(only Audio
CD (CD DA))
Note
- Discs which cannot be played with this
player.
DVD-ROM • DVD-RAM
CD-ROM • CDV
CDI • CVD
Super Audio CD(except CD layer)
CDGs play audio only, not graphics.
- Ability to play back may depend on recording
conditions.
DVD-R, +R
CD-RW
DVD+RW, -RW (V mode)
- The unit may not play certain CD-R, CD-RW
and DVD-R due to the disc type or recording
conditions.
COPY PROTECTION
Many DVD discs are encoded with copy
protection. Because of this, you should only connect
your DVD player directly to your TV, not to a VCR.
Connecting to a VCR results in a distorted picture
from copy-protected DVD discs.
This product incorporates copyright protection
technology that is protected by methods claims of
certain U.S. patents and other intellectual property
rights owned by Macrovision Corporation and other
rights owners. Use of this copyright protection
technology must be authorized by Macrovision
Corporation, and is intended for home and other
limited viewing uses only unless otherwise authorized
by Macrovision Corporation. Reverse engineering or
disassembly is prohibited.
PROGRESSIVE SCAN OUTPUTS
(480p)
“CONSUMERS SHOULD NOTE THAT NOT ALL HIGH
DEFINITION TELEVISION SETS ARE FULLY
COMPATIBLE WITH THIS PRODUCT AND MAYCAUSE
ARTIFACTS TO BE DISPLAYED IN THE PICTURE, IF
PROGRESSIVE SCAN PICTURE PROBLEMS OCCUR, IT
IS RECOMMENDED THAT THE USER SWITCH THE
CONNECTION TO THE ‘STANDARD DEFINITION’(VIDEO)
OUTPUT. IF THERE ARE QUESTIONS REGARDING
YOUR TV SET COMPATIBILITYWITH THIS DVDPLAYER,
PLEASE CONTACT SAMSUNG'S CUSTOMER SERVICE
CENTER.”
ENG-8
SETUP
Disc Type and Characteristics
This DVD player is capable of playing the following types of discs with the corresponding logos:
Disc Markings Region Number
Both the DVD player and the discs are
coded by region. These regional
codes must match in order for the disc
to play. If the codes do not match, the
disc will not play.
The Region Number for this player
is described on the rear panel of the
player.
5”
3 1/2”
Single-sided 240 min.
Double-sided 480 min.
Single-sided 80 min.
Double-sided 160 min.
Audio
+
Video
- DVD contains excellent sound and
video due to Dolby Digital and
MPEG-2 system.
- Various screen and audio functions
can be easily selected through the
on-screen menu.
Disc Types (Logos)
Recording Types Disc Size Max. Playing Time Characteristics
DVD
5”
3 1/2”
74 min.
20 min.
Audio
- CD is recorded as a Digital Signal with
better audio quality, less distortion and
less deterioration of audio quality over
time.
AUDIO-CD
~
DIGITAL
SOUND
STEREO
NTSC
Play Region Number
NTSC broadcast system in U.S.A, Canada, Korea,
Japan, etc.
Dolby Digital disc
Stereo disc
Digital Audio disc
DTS disc
MP3 disc
You must only insert one DVD disc at a time.
Inserting two or more discs will not allow
playback and may cause damage to the DVD
player.
DivX Certification
DivX, DivX Certified,
and associated logos are
trademarks of DivXNetworks, Inc and
are used under license
ENG-9
Setup
SETUP
Description
Front Panel Controls
1. STANDBY/ON ( )
When STANDBY/ON is pressed on, the indicator goes out
and the player is turned on.
2. STANDBY Indicator
When the unit is first plugged in, this indicator lights up.
3. DISC TRAY
Place the disc here.
4. OPEN/CLOSE ( )
Press to open and close the disc tray.
5. DISPLAY
Operation indicators are displayed here.
6. SKIP ( / ) SEARCH
Allow you to search forward/backward through
a disc. Use to skip the title, chapter or track.
7. STOP ( )
Stops disc play.
8. PLAY/PAUSE ( )
Begin or pause disc play.
9. USB Host
Connect digital still camera, MP3 player, memory stick, Card
reader, or other removable storage devices.
Front Panel Display
Displays the Total playing time and
various messages concerning
operations such as PLAY, STOP, LOAD ...
NOdSC: No disc loaded.
OPEn: The disc tray is open.
LOAd: Player is loading disc information.
1
6
7
8
2
3
5
4
DVD-P380
9
6
ENG-10
SETUP
Rear Panel
1. DIGITAL AUDIO OUT JACKS
- Use either an coaxial digital cable to connect to a
compatible Dolby Digital receiver.
- Use a coaxial digital cable to connect to an A/VAmplifier
that contains a Dolby Digital, MPEG2 or DTS decoder.
2. COMPONENT VIDEO OUT JACKS
- Use these jacks if you have a TV with Component
Video in jacks. These jacks provide P
R
, P
B
and Y video.
-If
P-SCAN (480p)
is set to “ON” in Video Output of
the Setup Menu, progressive scan mode will work.
-If
I-SCAN (480i)
is set to “ON” in Video Output of the
Setup Menu, interlaced scan mode will work.
3. AUDIO OUT JACKS
Use audio cables to connect to the Audio input jacks of
your television or audio/video receiver
4. VIDEO OUT JACK
- Use a video cable to connect to the Video input jack on
your television.
Note
-
Consult your TV User’s Manual to find out if your TV supports Progressive Scan (P-SCAN).
If Progressive Scan is supported, follow the TV User’s Manual regarding Progressive Scan settings in the
TV’s menu system.
- See pages 49 ~ 50 to get more information on how to use the setup menu.
1
34
2
ENG-11
Setup
SETUP
Tour of the Remote Control
1. DVD POWER Button
Turns the power on or off.
2. NUMBER Buttons
3. ZOOM Button / (-/--)
Enlarges the DVD Picture / Use this button to select the
channel of TV program by inserted the channel number
(TV mode).
4. SEARCH Buttons (
/
)
Allow you to search forward/backward through a disc.
5. VIDEO SEL. Button
Selects video output formats.
6. TV VOL (+, -) Buttons
Controls volume.
7. SKIP Buttons (
/
)
Use to skip the title, chapter or track.
8. STOP Button ( )
9. MENU Button
Brings up the DVD player’s menu.
10. ENTER/
/
,
¦¦
/
Buttons
This button functions as a toggle switch.
11. EZ VIEW Button
The aspect ratio of a picture can easily be adjusted
according to the screen size of your TV (16:9 or 4:3).
12. DISC MENU Button
Brings up the Disc menu.
13. OPEN/CLOSE ( ) Button
To open and close the disc tray.
14. AUDIO Button
Use this button to access various audio functions on a disc.
15. DVD Button
Press this button when you use a DVD player.
16. TV Button
Press this button to operate TV (only Samsung TV).
17. REPEAT A-B (Number 8) Button
Allows you to repeat play A-B on a disc.
18. STEP Button/TV Source
Advances play one frame at a time / Press this button to
select an available TV source (TV mode).
19. SUBTITLE Button
20. TV CH ( , ) Buttons
Channel selection.
21. PLAY/PAUSE Button ( )
Begin/Pause disc play.
22. RETURN Button
Returns to a previous menu.
23. INFO Button
Displays the current disc mode.
24. CANCEL Button
Use to remove menus or status displays from the screen.
25. USB Button
Each time the USB button is pressed, a display of USB
device selection will appear.
26. REPEAT Button
Allows you to repeat play a title, chapter, track, or disc.
1
2
3
4
5
6
7
8
9
10
15
11
12
13
16
17
18
19
20
21
22
23
24
14
25
26
ENG-12
Chapter 2
CONNECTIONS
Choosing a Connection
The following shows examples of connections commonly used to connect the DVD player with a TV
and other components.
Before Connecting the DVD Player
- Always turn off the DVD player, TV, and other devices before you connect or disconnect any
cables.
- Refer to the user’s manual of the additional devices (such as a TV) you are connecting formore
information on those particular devices.
Connecting to a TV (Progressive)
- Connecting to your TV using Component video cables.
- You will enjoy high quality and accurate color reproduction images. Component video separates
the picture element into black and white(Y), blue (PB), red (PR) signals to present clear and clean
images. (Audio signals are delivered through the audio output).
1
Using Component video cables (not included), connect the
COMPONENT VIDEO OUT jacks on the rear of the DVD player
to the COMPONENT IN jacks of your TV.
To see the progressive video output,
- Consult your TV Users Manual to find out if your TV supports Progressive Scan. If Progressive
Scan is supported, follow the TV Users Manual regarding Progressive Scan settings in the TV’s
menu system.
- Depending on your TV, the connection method may differ from the illustration above.
2
Using the audio cables, connect the AUDIO (red and white)
OUT jacks on the rear of the DVD player to the AUDIO (red
and white) IN jacks of your TV.
Turn on the DVD player and TV.
4
Set the Video Output to P-SCAN (480p) in the display Setup
menu (See pages 49-50)
3
Press the input selector button on your TV remote control until
the Component signal from the DVD player appears on the TV
screen.
RED
WHITE
RED WHITE
RED
BLUE
GREEN
RED
BLUE
GREEN
Audio Cable
(Included)
Component cable
(not included)
ENG-13
Connections
CONNECTIONS
Connecting to a TV (Interlace)
- Connecting to your TV using Component video cables.
- You will enjoy excelllent quality and accurate color reproduction images. Component video
separates the picture element into black and white(Y), blue(P
B
), red(P
R
) signals to present clear
and clean images. (Audio signals are delivered through the audio output.)
Note
- If you want to connect to an Amplifier, please refer to the Amplifier connection page. (See pages 15 to 16)
- The component jack of your TV may be marked “R-Y, B-Y, Y” or “Cr, Cb, Y” instead of “P
R
, P
B
, Y”
depending on the manufacturer. The number and position of the jacks may vary depending on the TV set.
Please refer to the user's manual of your TV.
1
Using Component video cables (not included), connect the
COMPONENT VIDEO OUT jacks on the rear of the DVD player
to the COMPONENT IN jacks of your TV.
2
Using the audio cables, connect the AUDIO (red and white)
OUT jacks on the rear of the DVD player to the AUDIO (red
and white) IN jacks of your TV.
Turn on your DVD player and TV.
4
Press the input selector on your TV remote control until the
Component signal from the DVD player appears on the TV
screen.
3
Set the Video Output to I-SCAN (480i) in the Display Setup
menu. (See pages 49 to 50)
RED
WHITE
RED
WHITE
RED
BLUE
GREEN
RED
BLUE
GREEN
Audio Cable
(Included)
Component cable
(not included)
ENG-14
CONNECTIONS
1
Using Video/Audio cables, connect the VIDEO (yellow)/AUDIO
(red and white) OUT jacks on the rear of the DVD player to the
VIDEO (yellow)/AUDIO (red and white) IN jacks of your TV.
2
Turn on your DVD player and TV.
Note
- Noise may be generated if the audio cable placed too close to the power cable.
- If you want to connect to an Amplifier, please refer to the Amplifier connection page. (See pages 15 to 16)
- The number and position of the jacks may vary depending on your TV set. Please refer to the user's manual
of your TV.
- If there is one audio input terminal on the TV, connect it to the [AUDIO OUT][left] (white) jack of the DVD
player.
3
Press the input selector button on your TV remote control until
the Video signal from the DVD player appears on the TV
screen.
Connecting to a TV (Video)
DIGITAL AUDIO
RED
WHITE
YELLOW
RED
WHITE
YELLOW
Audio
Cable
Video
Cable
ENG-15
Connections
CONNECTIONS
Note
- Please turn the volume down when you turn on the Amplifier. Sudden loud sound may cause
damage to the speakers and your ears.
- Please set the audio in the menu screen according to the Amplifier.(See pages 47 to 48)
- The position of jacks may vary depending on the Amplifier.
Please refer to the user's manual of the Amplifier.
Connecting to an Audio System (2 Channel Amplifier)
DIGITAL AUDIO
1
Using the audio cables, connect the AUDIO (red and white)
OUT jacks on the rear of the DVD player to the AUDIO (red
and white) IN jacks of the Amplifier.
2
Using the video signal cable(s), connect the VIDEO ,
COMPONENT jacks on the rear of the DVD player to the
VIDEO, COMPONENT jacks of your TV as described on pages
12 to 16.
3
Turn on your DVD player, TV, and Amplifier.
4
Press the input select button of the Amplifier to select the audio
input your DVD player is connected to in order to hear sound.
Refer to your Amplifier's user manual to set the Amplifier's
audio input.
RED
WHITE
RED
WHITE
2-Channel stereo amp
Audio Cable
(Included)
ENG-16
CONNECTIONS
Note
- Please turn the volume down when you turn on the Amplifier. Sudden loud sound may cause
damage to the speakers and your ears.
- Please set the audio in the menu screen according to the Amplifier you have connected. (See pages 47 to 48)
- The position of jacks may vary depending on the Amplifier.
Please refer to the user's manual of the Amplifier.
Connecting to an Audio System (Dolby digital, MPEG2 or DTS Amplifier)
DIGITAL AUDIO
1
If using a Coaxial cable (not included), connect the DIGITAL
AUDIO OUT (COAXIAL) jack on the rear of the DVD player to
the DIGITAL AUDIO IN (COAXIAL) jack of the Amplifier.
2
Using the video signal cable(s), connect the VIDEO,
COMPONENT jacks on the rear of the DVD player to the
VIDEO, COMPONENT jacks of your TV as described on pages
12 to 14.
3
Turn on your DVD player, TV, and Amplifier.
4
Press the input select button of the Amplifier to select the audio
input your DVD player is connected to in order to hear sound.
Refer to your Amplifier's user manual to set the Amplifier's
audio input.
Coaxial Cable
(not included)
Dolby digital or
DTS amp
ENG-17
Basic Functions
Chapter 3
BASIC FUNCTIONS
Playing a Disc
Before Play
- Turn on your TV and set it to the Video Input your DVD player is connected to with your TV’s
remote control.
- If you connected the DVD player to an external Audio System, turn on your Audio System and set
it to the correct Audio Input.
After plugging in the player, the first time you press the DVD POWER button, the screen
to the right appears: If you want to select a language, press a NUMBER button.
(This screen will only appear when you plug in the player for the first time.)
If the language for the startup screen is not set, the settings may change whenever you
turn the power on or off. Therefore, make sure that you select the language you want to
use.
Once you select a menu language, you can change it by pressing the button on the
front panel of the unit for more than 5 seconds with no disc in the unit. Then the
SELECT MENU LANGUAGE window appears again where you can reset your
preferred language.
Playback
1
Press the OPEN/CLOSE
()button.
The STANDBY indicator
light goes out and the tray
opens.
2
Place a disc gently into the
tray with the disc’s label
facing up.
3
Press the PLAY/PAUSE ( )
button or OPEN/CLOSE ( )
button to close the disc tray.
RESUME function
When you stop disc play, the player remembers
where you stopped, so when you press the
PLAY/PAUSE ( ) button again, it will pick up
where you left off.
ENG-18
BASIC FUNCTIONS
4
Stopping Play
Press the STOP ( ) button
during play.
Note
- If the player is left in the stop mode for more than
one minute without pressing any buttons, a
screen saver will be activated. Press the
PLAY/PAUSE ( ) button to resume normal play.
- If the player is left in the stop mode for more than
30 minutes, the power will automatically turn off.
6
Pausing Play
Press the PLAY/PAUSE
()or STEP button on the
remote control during play.
Screen stops, no sound.
To resume, press the PLAY/PAUSE ( ) button
once again.
Note
If the player is left for about 5 minutes in pause
mode, it will stop.
7
Step Motion Play (Except
CD)
Press the STEP button on
the remote control during
play.
Each time the button is pressed, a new frame
will appear.
No sound is heard during STEP mode.
Press the PLAY/PAUSE ( ) button to resume
normal play.
You can only perform step motion play in the
forward direction.
No sound is heard during slow mode.
Press the PLAY/PAUSE ( ) button to resume
normal play.
5
Removing the Disc
Press the OPEN/CLOSE
()button.
8
Slow Motion Play
Press the SEARCH (
/
)
button to choose the play
speed between 1/8, 1/4 and
1/2 of normal speed during
PAUSE or STEP mode.
Note
- The ( ) icon indicates an invalid button press.
- This player does not play HD DVDs or Blu-Ray
discs.
Basic Functions
ENG-19
BASIC FUNCTIONS
Using the Search and Skip Functions
During play, you can search quickly through a chapter or track, and use the skip function to jump to
the next selection.
Searching through a Chapter or Track
During play, press the
SEARCH ( or ) button
on the remote control for
more than 1 second.
If you want to search at a faster speed on the
DVD or CD, press and hold the button.
Note
- The speed marked in this function may be
different from the actual playback speed.
- No sound is heard during search mode
(Except CD).
DVD
CD
2X, 4X, 64X, 128X
2X, 4X, 8X
Skipping Tracks
- When playing a DVD, if you press the SKIP ( )
button, it moves to the next chapter. If you press
the SKIP ( ) button, it moves to the beginning
of the chapter. Pressing the Skip button twice
makes the DVD move to the beginning of the
previous chapter.
- When playing a CD, if you press the SKIP ( )
button, it moves to the next track. If you press
the SKIP ( ) button, it moves to the beginning
of the track. Pressing the Skip button twice
makes the DVD move to the beginning of the
previous track.
During play, press the SKIP
( or ) button.
ENG-20
BASIC FUNCTIONS
Using the Display Function
When Playing a DVD/MPEG4
1
During play, press the
INFO button on the remote
control.
You can select Info in the function menu by
pressing the MENU button.
2
Press the / buttons to
select the desired item.
3
Press the ¦/ buttons to
make the desired setup and
then press the ENTER
button.
You may use the number buttons of the remote
control to directly access a title, chapter or to
start the playback from a desired time.
4
To make the screen
disappear, press the INFO
button again.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116

Samsung DVD-P380 Manuel utilisateur

Catégorie
Lecteurs DVD
Taper
Manuel utilisateur

dans d''autres langues