Little GIANT 6-CIM Le manuel du propriétaire

Marque: Little GIANT

Modèle: 6-CIM

Catégorie: Pompes à eau

Taper: Le manuel du propriétaire

littlegiant.com

MODEL 6 & 8 SERIES

Owner’s Manual

Sump Pumps

Table of Contents

SAFETY INSTRUCTIONS - - - - - - - - 2

INTRODUCTION - - - - - - - - - - - 4

PRODUCT DESCRIPTION - - - - - - 4

INSTALLATION - - - - - - - - - - - - 5

PHYSICAL INSTALLATION - - - - - 5

ELECTRICAL CONNECTIONS - - - - 7

OPERATION TESTING - - - - - - - - - 9

MAINTENANCE - - - - - - - - - - - - 12

PERIODIC SERVICE - - - - - - - - - 12

TROUBLESHOOTING - - - - - - - - 13

REPLACEMENT PARTS - - - - - - - 14

STANDARD LIMITED WARRANTY - - - 15

SAFETY INSTRUCTIONS

Hazard Messages

SAFETY INSTRUCTIONS

Hazard Messages

This manual includes safety precautions and other important

information in the following formats:

IMPORTANT: Identifies information that controls correct assem-

bly and operation of the product.

NOTE: Identifies helpful or clarifying information.

This symbol alerts the user to the presence of dangerous

voltage inside the product that might cause harm or elec-

trical shock.

This symbol alerts the user to the presence of hot sur-

faces that might cause fire or personal injury.

Before Getting Started

This equipment should be installed and serviced by technically

qualified personnel who are familiar with the correct selection

and use of appropriate tools, equipment, and procedures. Failure

to comply with national and local electrical and plumbing codes

and within Little Giant recommendations may result in electrical

shock or fire hazard, unsatisfactory performance, or equipment

failure.

Know the product’s application, limitations, and potential haz-

ards. Read and follow instructions carefully to avoid injury and

property damage. Do not disassemble or repair unit unless

described in this manual.

Refer to product data plate(s) for additional precautions, operat-

ing instructions, and specifications.

Failure to follow installation or operation procedures and all

applicable codes may result in the following hazards:

Indicates an imminently hazardous situation

which, if not avoided, will result in death or

serious injury.

Indicates a potentially hazardous situation

which, if not avoided, could result in death or

serious injury.

Indicates a potentially hazardous situation

which, if not avoided, could result in minor or

moderate personal injury.

Indicates a potentially hazardous situation

which, if not avoided could result in damage to

equipment or other property.

Risk of death, personal injury, or

property damage due to explosion, fire,

or electric shock.

• Do not use to pump flammable or explosive fluids such as

gasoline, fuel oil, kerosene, etc.

• Do not use in explosive atmospheres or hazardous loca-

tions as classified by the NEC, ANSI/NFPA70.

• Do not handle a pump or pump motor with wet hands or

when standing on a wet or damp surface, or in water.

• When a pump is in its application, do not touch the motor,

pipes, or water until the unit is unplugged or electrically

disconnected.

• If the power disconnect is out of sight, lock it in the open

position and tag it to prevent unexpected application of

power.

• If the disconnect panel is not accessible, contact the elec-

tric company to stop service.

SAFETY INSTRUCTIONS

Before Getting Started

Except CB Models

High voltages capable of causing severe

injury or death by electrical shock are

present in this unit.

• To reduce risk of electrical shock, disconnect power before

working on or around the system. More than one discon-

nect switch may be required to de-energize the equipment

before servicing.

• Be certain that this pump is connected to a circuit

equipped with a ground fault circuit interrupter (GFCI)

device.

• Wire pump system for correct voltages.

• The pump has been evaluated for use with water only.

Pump should only be used with liquids compatible with

pump component materials. If the pump is used with liq-

uids incompatible with the pump components, the liquid

can cause failure to the electrical insulation system result-

ing in electrical shock.

Risk of damage to pump or other equipment.

• Do not use this pump for pumping sea water, beverages,

acids, chemical solutions, or any other liquid that pro-

motes corrosion as this can result in damage to the pump.

• Do not run pump dry. For optimal cooling and to prolong

the motor life, the liquid level being pumped should nor-

mally be above the top of the pump housing.

• This pump is not suitable for pond applications.

Risk of bodily injury, electric shock,

or property damage.

• This equipment must not be used by children or persons

with reduced physical, sensory, or mental abilities, or lack-

ing in experience and expertise, unless supervised or

instructed. Children may not use the equipment, nor may

they play with the unit or in the immediate vicinity.

• Equipment can start automatically. Always unplug the

pump power cord and disconnect the electrical power

before servicing the pump or switch. Lockout-Tagout

before servicing equipment.

• An inoperative or malfunctioning pump could lead to

flooding, resulting in personal injury or property damage.

• In applications where property damage and/or personal

injury might result from an inoperative or leaking pump

due to power outages, discharge line blockage, or any

other reason, an automatic back-up system and/or an

alarm should be installed.

• Do not run the pump dry. If run dry, the surface tempera-

ture of the pump will rise to a high temperature that could

cause skin burns if touched, and will cause serious dam-

age to the pump.

• Do not oil the motor. The pump’s motor housing is sealed,

and contains a high-grade dielectric oil for heat transfer

and lifetime lubrication. Use of other oils could cause seri-

ous electric shock and/or permanent damage to the

pump.

• Operation of this equipment requires detailed installation

and operation instructions provided in this manual for use

with this product.

• Read entire manual before starting installation and opera-

tion.

• End User should receive and retain manual for future use.

• Keep safety labels clean and in good condition.

• Keep work area clean, well-lit, and uncluttered.

• Wear safety glasses while installing or performing mainte-

nance on the pump.

• Do not wear loose clothing, jewelry, or anything that may

be caught in the rotating parts. Tie up long hair and

remove jewelry.

INTRODUCTION

Product Description

INTRODUCTION

Product Description

This submersible pump is for use in basins or lift stations and is suitable for pumping clear water. Do not use

the pump in applications where effluent (gray water), sewage, or any other debris (gravel, sand, floating

debris, etc.), abrasives, or corrosives are present. Both automatic and manual versions of these pumps are

available.

These products have been carefully tested, inspected, and packaged to ensure safe delivery and operation.

Please examine your pump carefully to ensure that no damage occurred during shipment. If damage has

occurred, please contact the place of purchase. They will assist you in replacement or repair, if required.

The pump motor is equipped with an automatic resetting thermal protector, and may restart unexpectedly.

Thermal Protector tripping is an indication of motor overloading or overheating, which can be caused by

application issues such as an obstructed pump impeller, switch stuck in the ON position, pump running dry,

pump air-locked, pump short cycling, excessively high or low voltage supply, or possibly a pump, motor,

bearings, or seal that have reached the end of their useful life.

Models

* Pumps are not dual voltage.

Manual pumps can be converted to Automatic mode by installing a separate liquid level control, such as an

RS-5 Remote Switch kit.

Flow Rates

Model HP PSI Voltage Pump Activation Method

6-CIA 1/3 7.8 115 or 230* Automatic with Diaphragm Switch

6-CIM 1/3 7.8 115 or 230* Manual

6-CIM-R 1/3 7.8 115 Manual

6-CIM-RS 1/3 7.8 115 Automatic with Remote Diaphragm Switch

6-CIA-RFS 1/3 7.8 115 Automatic with Remote Float Switch

8-CIA 4/10 9.9 115 Automatic with Diaphragm Switch

8-CBA 4/10 9.9 115 Automatic with Diaphragm Switch

8-CIM 4/10 9.9 115 Manual

8-CBM 4/10 9.9 115 Manual

Gallons/Liters per Minute

At Height: (Head)

5 ft

1.5 m

10 ft

3 m

15 ft

4.5 m

Shut Off

6 Series 46 / 174 29 / 110 12.5 / 47.3 18 ft/5.5 m

8 Series 54 / 204 42 / 159 26 / 98 22.9 ft/7 m

INSTALLATION

Physical Installation

INSTALLATION

Physical Installation

1. Pump must be installed in a suitable basin that is at least 18" in diameter and 24" deep in accordance

with local plumbing codes.

2. Clean any debris from the basin and set the pump in the center of the basin (refer to “

Typical Installa-

tion” on page 6).

3. The pump must be placed on a hard, level surface. Never place the pump directly on clay, earth or

gravel surfaces. These surfaces contain small stones, gravel, sand etc. that may clog or damage the

pump and cause pump failure.

4. Do not attempt to restrict the intake side of these pumps. Restricting the intake may cause damage to

the seal and may starve the pump. If you require reduced flow rates, place a valve on the discharge side

of the pump. Or, if flexible vinyl tubing is used, a clamp can be used on the tubing to restrict the flow.

5. Connect discharge piping. Use pipe joint compound at all connections. Sump pumps can be piped to

discharge into the house drainage system, to a dry well, splash block, or to a storm drain, depending on

local plumbing codes. The discharge pipe should be as short as possible and contain as few elbows as

possible. The discharge pipe should be the same diameter, or larger than, the pump discharge size. A

smaller pipe will restrict capacity and reduce pump performance. The pump comes with a 1-1/2" female

pipe thread discharge

and a 1-1/4” FNPT reducing bushing.

• Support the pump and piping while assembling and when installed. Failure to do so may cause the

piping to break, the pump to fail, motor bearing failures, etc.

• Always install a union in the discharge line just above the basin cover to allow for easy removal of

the pump for cleaning or repair.

6. A full flow check valve must be used in the discharge line to prevent back-flow of liquid into the basin.

A missing, improperly installed or malfunctioning check valve can cause a pump to short-cycle due to

backflow of the pumped fluid from the discharge plumbing back into the basin, significantly shortening

the life of the pump.

7. Tape the pump and switch cords to the discharge pipe with electrical tape to keep the power cords

securely routed away from the pump inlet and any control floats.

IMPORTANT: Automatic models using a diaphragm switch include a breather tube that runs through

the power cord. On models with a hardwired connection, this tube extends from the end of the cord. On

models with a plug, the tube is integrated into the plug. Be sure the tube is not obstructed, pinched, or

kinked during installation.

Risk of severe injury or death by electrical shock.

• Always disconnect the electrical power before touching the pump or discharge.

• Check local electrical and building codes before installation. The installation must be in accordance

with their regulations as well as the most recent National Electrical Code (NEC).

Risk of property damage due to flooding.

• When a check valve is used, drill a relief hole (1/8" or 3/16" in diameter) in the discharge pipe. This

hole should be located below the floor line between the pump discharge and the check valve. Unless

such a relief hole is provided, the pump could “air lock” and will not pump water even though it will

run.

INSTALLATION

Physical Installation

8. Connect the pump to an appropriate power supply following the instructions in “Electrical Connec-

tions” on page 7.

9. Test the operation of the pump system by following the instructions in “

Operation Testing” on page 9

of this manual. Do not attempt to operate the pump without water; this will damage the seals and

bearings and could result in permanent damage to the pump.

10. Place cover over basin. This cover will help prevent debris from entering the pit and will guard against

accidental injury.

Typical Installation

Check Valve

Wall

Sump Cover

4 Ft Minimum

Union or Hose

Connection

Footing

Sump Pit 18” Diameter

Minimum x 24” Deep

Typical Poured

Concrete Bottom

3/16” Dia. Bleed

Hole in Discharge

Pipe

Power Cord

Taped to Pipe

On Level

Off Level

Discharge Pipe no smaller

than Pump Outlet

Separate Protected and

Grounded Service Outlet

INSTALLATION

Electrical Connections

Wiring Guidelines

Check the pump label for proper voltage required. Do not connect to voltage other than that shown.

Be certain that this pump is connected to a circuit equipped with a ground fault circuit interrupter (GFCI)

device.

The pump should be connected or wired to its own circuit, with no other electric receptacles or equipment

in the circuit. The fuses or circuit breaker should be of ample capacity in the electrical circuit.

Risk of severe injury or death by electrical shock.

• Always disconnect the electrical power before touching the pump or discharge.

• Some pumps are supplied with lead wires and are intended to be hardwired using a junction box or

other approved enclosure. The pumps include a grounding connector. To reduce risk of electric

shock, be certain that it is properly connected to ground.

• Some pumps are supplied with a grounding conductor and grounding-type attachment plug. To

reduce risk of electric shock, be certain that it is connected only to a properly grounded grounding-

type receptacle. Do not remove the third prong from the plug. The third prong is to ground the pump

to help prevent possible electric shock hazard.

• Check electrical outlets with a circuit analyzer to ensure power, neutral, and ground wires are prop-

erly connected. If not, a qualified, licensed electrician should correct the problem.

• The flexible jacketed cord assembly mounted to the pump must not be modified in any way,

with the exception of shortening the cord to fit into a control panel. Any splice between the

pump and the control panel must be made within a junction box mounted outside of the

basin and comply with the National Electrical Code.

• Do not use the power cord for lifting the pump.

• Do not remove the third prong from the plug, or cut plug from cord. These actions will void the war-

ranty.

• Do not use an extension cord.

Pump Model

Voltage Breaker Amps

6-Series 230 V 10 A

6- and 8-Series 115 V 15 A

INSTALLATION

Electrical Connections

Power Supply

Models With Stripped Wire Ends

Some models are supplied with a stripped wire cord end. Power connections,

along with any liquid level control, must be made within a junction box

mounted outside of the basin, and must comply with the National Electrical

Code. Employ a licensed electrician.

The power cord wires are color coded as follows:

• Green (or green/yellow) - ground

• Black (or brown) - line, and

• White (or blue) - line (230 V) or neutral (115 V)

To add a liquid level control to a hardwired pump, use the diagram to the right.

Automatic Pump Models

Pumps equipped with an integral automatic diaphragm switch include one master power

cord for both the pump and the switch. Plug the cord into a GFCI outlet.

Models with a float switch, or remote diaphragm switch, include two power cords with a

piggyback plug on the switch cord. For automatic operation, plug the pump cord into the

switch cord. Plug the switch cord (with pump cord attached) into a GFCI outlet.

Manual Pump Models

Manual pumps are plugged into a dedicated GFCI receptacle and are controlled by either

by switching the power or by unplugging the cord.

Manual, continuous pump operation should be used only for emergencies, or when a

large volume of water is to be pumped. The pump must be continuously monitored

during manual operation and disconnected from power before the pump runs dry.

Manual pumps can be converted to automatic mode by installing a separate liquid level control. Install

according to the manufacturer’s instructions.

Risk of severe injury or death by electrical shock.

• In a 230 V direct wire installation, one side of the line going to the pump is always electrically ener-

gized, regardless of whether the liquid level control switch is open or closed. To avoid hazards when

installing or servicing, install a double-pole disconnect near the pump installation.

• Be sure the electrical connection cannot be reached by rising water. Under no circumstances should

the junction box be located where it may become flooded or submerged by water.

OPERATION TESTING

Testing Automatic Pump Operation

OPERATION TESTING

If the pump does not operate properly, refer to “Troubleshooting” on page 13. If the solution still cannot be

found, please contact the place of purchase or an authorized service center.

Do not let the unit run dry (without liquid). It is designed to be cooled by pumping fluid. The seal may be

damaged and the motor may fail if the pump is allowed to run dry.

If the unit is going to be idle for a period of time, follow the cleaning instructions in “

Cleaning Impeller and

Volute” on page 12. Do not let the unit freeze. This may cause cracking or distortion that may destroy the

unit.

Testing Automatic Pump Operation

Pump models 6-CIA, 6-CIA-RS, 8-CIA, and 8-CBA are equipped with a diaphragm switch that operates by

balancing water and air pressure. Rising water in the basin applies pressure to the diaphragm, which acti-

vates the switch, turning on the pump. As the water level falls, the pressure decreases until the switch deac-

tivates, turning off the pump. For the switch to function properly, it is vented to the atmosphere through a

breather tube routed through the pump’s power cord. Non-restrictive air flow in the breather tube is

required.

Pump model 6-CIA-RFS is equipped with a remote float switch with a piggyback plug on the switch cord.

The pump must be plugged into the piggyback switch cord for automatic operation.

When the pump is installed in a basin with a sealed cover, pump operation cannot be observed. The basin

cover will usually have a spare hole that is plugged with a rubber plug. This plug can be removed and pump

operation can be observed.

To test system operation, follow these steps:

1. Connect the pump to an appropriate power supply with voltage consistent with the pump voltage, as

indicated on the pump nameplate.

2. If there is a gate valve on the discharge line, be sure the valve is open.

3. Run water into the basin until the pump is activated. Do not attempt to run the pump without water;

this could result in permanent damage to the pump.

4. Confirm that the pump and its control switch are functioning as intended.

NOTE: If the pump doesn’t turn on, test the switch. Refer to “

Testing the Diaphragm Switch” on page 10

or “

Testing the Float Switch” on page 10.

5. Confirm that the ON/OFF levels are within specification, and confirm that no potential obstructions

exist that could inhibit switch operation.

6. Confirm that there are no leaks in the pump discharge plumbing and main home drain pipe plumbing.

NOTE: It is normal for a stream of water to spray from the air bleed hole in the pump’s plumbing. Water

also sprays out of a hole in the base of the unit. Confirm that this spray is captured within the basin.

7. Allow the pump to operate through several on/off cycles.

Risk of damage to pump or other equipment.

• Do not attempt to run the pump without water; this could result in permanent damage to the pump.

• If pump is run dry, it may damage pump and void the warranty.

OPERATION TESTING

Testing Automatic Pump Operation

Testing the Diaphragm Switch

NOTE: This test is recommended for bench testing only.

To test the functionality of the diaphragm switch without submersing it in water, suction (vac-

uum) must be applied to the open end of the breather tube (1) at the power cord plug or

stripped end of the power cord.

Suction can be applied using a suction bulb syringe (2).

The suction causes the switch diaphragm to draw inward, activating the switch inside the

switch housing. When syringe is released, the diaphragm returns to its original position deacti-

vating the switch inside the switch housing.

1. Squeeze the bulb of the syringe.

2. Insert the small end into the breather tube of the power cord.

3. Release the bulb to induce suction/vacuum.

4. Listen for the switch to make a click sound.

5. Once the suction/vacuum equalizes, listen for the diaphragm switch to release.

Testing the Float Switch

A float switch can be bench tested by using an ohmmeter to check

for continuity between the incoming and outgoing connections of

the piggyback plug while raising and lowering the float.

OPERATION TESTING

Testing Manual Pump Operation

Pump models 6-CIM, 6-CIM-R, 8-CIM, and 8-CBM are manual pumps.

For automatic operation of a manual pump, a separate float switch or other liquid level control may be used.

If a float switch or level control has been added, refer to “

Testing Automatic Pump Operation” on page 9 for

test procedure.

To test manual pump operation, follow these steps:

1. Connect a discharge hose to the pump's discharge port.

2. Place pump into a basin or test reservoir.

3. Direct the opposite end of the discharge hose back into the basin or test reservoir so that the water dis-

charged from the hose during testing will be contained within the basin or test reservoir. Secure the

hose to prevent the water pressure created during testing from causing the hose to exit the basin or

test reservoir.

4. If there is a gate valve on the discharge line, be sure the valve is open.

5. Using a separate water source, fill the basin or test reservoir until the pump is fully submerged. Do not

attempt to run the pump without water; this could result in permanent damage to the pump. Do not

overfill the basin or test reservoir.

6. If the pump is provided with an attachment plug on the power cord, plug the pump's power cord into a

ground fault circuit interrupter (GFCI) receptacle with voltage consistent with the pump voltage, as

indicated on the pump nameplate.

If the pump is hardwired, turn on the circuit breaker for the pump's power circuit.

7. Confirm that the pump is functioning as intended.

8. If pump is not functioning as intended, disconnect power from the pump and refer to “

Troubleshoot-

ing” on page 13. If the solution still cannot be found, please contact the place of purchase or an autho-

rized service center.

9. If the pump is functioning as intended, disconnect power from the pump before attempting to remove

it from the basin or test reservoir.

Risk of bodily injury or damage to pump or other equipment.

• Manual, continuous pump operation should be used only for emergencies, or when a large volume of

water is to be pumped. The pump must be continuously monitored during operation and discon-

nected from power before the pump runs dry.

• If an accessory float switch or other liquid level control is installed, refer to manufacturer’s instruc-

tions. Failure to install control in compliance with national and local electrical and plumbing codes

and within manufacturer’s recommendations may result in electrical shock or fire hazard, unsatisfac-

tory performance, or equipment failure.

MAINTENANCE

Periodic Service

MAINTENANCE

Periodic Service

Inspect and test the pump system condition and operation every three months—more frequently in heavy

use applications.

1. Check the power cords, electric receptacle, and/or junction box for damage or corrosion.

The power cord on these units cannot be replaced. If damaged, replace the complete unit.

2. Remove all debris (gravel, sand, floating debris, etc.) from the basin.

3. Check the pump system components (basin, pump, switch, etc.) for any build-up (sludge, sediment,

minerals, etc.) that would inhibit functionality of the components. If significant, remove build-up or

replace affected components.

4. Confirm that all flexible coupling hose clamps are fully engaged with plumbing and fully tightened.

5. Test operation of the pump system. Refer to “

Operation Testing” on page 9.

6. While the pump is running, make sure a stream of water is escaping from the air bleed hole. If not, clear

the hole of any deposits or debris.

Cleaning Impeller and Volute

Periodic cleaning of the pump parts will prolong the life and efficiency of the pump. Refer to the assembly

and disassembly of the pumping head.

After removing power to the pump, disconnect the pump from the discharge plumbing.

1. Remove the five screws that hold the base to the volute, then separate the base from the volute.

2. Remove the base and clean the impeller and the volute passage. Do not use strong solvents on the

impeller.

3. Be sure the impeller turns freely after cleaning.

4. Attach the base to the volute, making sure the seal is properly aligned.

Risk of severe injury or death by electrical shock, high

temperatures, or pressurized fluids.

• Always unplug the pump power cord and disconnect the electrical power before servicing the

pump or switch.

• Let pump cool for a minimum of 2 hours before attempting to service. Submersible pumps contain

oil that becomes pressurized and hot under normal operating conditions.

Risk of damage to pump or other equipment.

• This unit is permanently lubricated. Oiling is not required. Do not open the sealed portion of the unit

or remove housing screws.

• Do not remove the motor housing cover.

• Do not remove the impeller

• Warranty is void if the motor housing cover, impeller, or seals have been removed. Repairs on the

motor or impeller require special tools.

MAINTENANCE

Troubleshooting

Problem Probable Causes Corrective Action

Pump does not turn on

Pump not connected to electrical

power.

Connect pump to a dedicated circuit equipped with GFCI.

Circuit breaker off or fuse removed. Turn on circuit breaker or replace fuse.

For models equipped with diaphragm

switch: Breather tube kinked, pinched

or blocked.

Confirm power cord is not kinked or pinched and confirm that

breather tube end opening is not blocked.

For models equipped with tethered

float switch: Accumulation of trash or

build-up on float.

Clean float.

For models equipped with tethered

float switch: Float obstruction.

Check float path and provide clearance.

Defective switch. Replace switch.

Defective motor. Replace pump.

Pump will not shut off

Float obstruction. Check float path and provide clearance.

Pump is air locked due to missing or

clogged air relief hole.

If missing, drill an air relief hole as described in “

Physical

Installation” on page 5. If clogged, clean obstruction from air

relief.

Liquid inflow matches pump capacity. Larger pump required.

For models equipped with diaphragm

switch: Breather tube kinked, pinched

or blocked.

Confirm power cord is not kinked or pinched and confirm that

breather tube end opening is not blocked.

Defective switch. Replace switch.

Pump runs but does not

discharge liquid

Check valve installed backwards. Check flow indicating arrow on check valve body to ensure

proper installation.

Check valve stuck or plugged. Remove check valve and inspect for proper operation.

Lift too high for pump. Check rated pump performance.

Inlet to impeller plugged. Pull pump and clean.

Pump is air locked due to missing or

clogged air relief hole.

If missing, drill an air relief hole as described in INSTALLA-

TION. If clogged, clean obstruction from air relief hole.

Pump does not deliver

rated capacity

Lift too high for pump. Check rated pump performance.

Low voltage, speed too slow. Check that supply voltage matches the nameplate rating.

Impeller or discharge pipe is clogged. Pull pump and clean. Check pipe for scale or corrosion.

Impeller wear due to abrasives. Replace pump.

Pump cycles continu-

ously

No check valve in long discharge pipe

allowing liquid to drain back into basin.

Install a check valve in discharge line.

Check valve leaking. Inspect check valve for correct operation.

Basin too small for inflow. Install larger basin.

Water sprays out of a

hole in the base of the

unit.

This pump comes with a bleed hole

that allows trapped air to escape from

the pump, preventing air lock.

Water spraying out of this hole is com-

pletely normal.

No corrective action is required.

MAINTENANCE

Replacement Parts

Item

No.

Part

Number

Description 6-CIM 6-CIA

6-CIM-

6-CIA-

RFS

8-CIM 8-CIA 8-CBM 8-CBA

1 108101 Handle, Pump 1 1 1 1 1 1 1 1

2 928004 Seal Ring 1 1 1 1 1 1 1 1

106079

106181

Pump Base, Air Bleed

Pump Base

–

909021

901350101

Screw/Washer #10-24 x 1/2”

5 108482 Screen Intake 1 1 1 1 1 1 1 1

6 599026 AD-6 Adapter 1 1 1 1 1 1 1 1

Not

Shown

599025

GH-3/4 Garden Hose

Adapter

1 - 1 1 - - - -

STANDARD LIMITED WARRANTY

THIS WARRANTY SETS FORTH THE COMPANY’S SOLE OBLIGATION AND PURCHASER’S EXCLUSIVE REMEDY FOR DEFECTIVE PRODUCT.

Franklin Electric Company, Inc. and its subsidiaries (hereafter “the Company”) warrants that the products accompanied by this warranty are free

from defects in materials or workmanship of the Company that exist at the time of sale by the Company and which occur or exist within the applica-

ble warranty period. Any distributor, sub-distributor, recipient, end-user and/or consumer agrees that by accepting the receipt of the products, the

distributor, sub-distributor, recipient, end user and/or consumer expressly agrees to be bound by the terms of the warranty set forth herein.

I. Applicable Warranty Period

The products accompanied by this warranty shall be covered by this Limited Warranty for a period of 36 months from the date of original purchase

by the consumer. In the absence of suitable proof of purchase date, the warranty period of this product will begin to run on the product's date of

manufacture.

II. Instructions Applicable to this Limited Warranty

1. Consumers wishing to submit a warranty claim must return the products accompanied by this warranty to the point of purchase for

warranty consideration.

2. Upon discovery of a defect, any personal injury, property damage or any other type of resulting damage, if applicable, shall be rea-

sonably mitigated to the extent possible.

3. At its discretion, the Company may inspect products either at its facilities or in the field, and after determination of a warranty

claim, will, at its option, repair or replace defective parts. Repaired or replaced parts will be returned freight prepaid by the Com-

pany.

4. This warranty policy does not cover any labor or shipping charges. The Company shall not be liable for any costs or charges attrib-

utable to any product testing, maintenance, installation, repair or removal, or for any tools, supplies, or equipment needed to install,

repair, or remove any product.

III. Limitations Applicable to this Limited Warranty

THIS WARRANTY DOES NOT APPLY TO ANY OF THE FOLLOWING:

1. Brushes, impeller or cam on models with brush-type motors and/or flex-vane impellers.

2. Any product that is not installed, applied, maintained, and used in accordance with the Company's published instructions, applica-

ble codes, applicable ordinances and/or with generally accepted industry standards.

3. Any product that has been subject to misuse, misapplication, neglect, alteration, accident, abuse, tampering, acts of God (including

lightning), acts of terrorism, acts of war, fire, improper storage or installation, improper use, improper maintenance or repair, dam-

age or casualty, or to an excess of the recommended maximums as set forth in the product instructions.

4. Any product that is operated with any accessory, equipment, component, or part not specifically approved by the Company.

5. Use of replacement parts not sold by the Company, the unauthorized addition of non-Company products to other Company prod-

ucts, and the unauthorized alteration of Company products.

6. Products damaged by normal wear and tear, normal maintenance services and the parts used in connection with such service, or

any other conditions beyond the control of the Company.

7. Any product that has been used for purposes other than those for which it was designed and manufactured.

8. Any use of the product where installation instructions and/or instructions for use were not followed.

9. Products connected to voltage other than indicated on nameplate.

10. Products where the pump was exposed to any of the following: sand, gravel, cement, grease, plaster, mud, tar, hydrocarbons,

hydrocarbon derivatives (oil, gasoline, solvents, etc.) or other abrasive or corrosive substances.

11. Products in which the pump has been used for pumping of liquids above 140 °F.

12. Products in which the pump was allowed to operate dry (fluid supply cut off).

13. Products in which the sealed motor housing has been opened or the product has been otherwise dismantled by customer.

14. Products in which the cord has been cut to a length of less than three feet.

Franklin Electric Co., Inc. | Oklahoma City, OK 73157-2010

800.701.7894 | littlegiant.com

For technical assistance, please contact:

Form 993865 Rev. 002 05/19

The Company reserves the right at any time, and from time to time, to make changes in the design and/or improvements upon its product without

thereby imposing any obligation upon itself to make corresponding changes or improvements in or upon its products already manufactured and/or

previously sold. The Company further reserves the right to substitute parts or components of substantially equal quality in any warranty service

required by operation of this Limited Warranty.

This written Limited Warranty is the entire warranty authorized and offered by the Company. There are no warranties or representations beyond

those expressed in this document.

THIS WARRANTY AND REMEDY IS IN LIEU OF ALL OTHER WARRANTIES AND REMEDIES INCLUDING WITHOUT LIMITATION, WARRANTIES OF MER-

CHANTABILITY AND/OR FITNESS FOR A PARTICULAR PURPOSE, WHICH ARE HEREBY SPECIFICALLY DISCLAIMED AND EXPRESSLY EXCLUDED.

CORRECTION OF NON-CONFORMITIES, IN THE MANNER AND FOR THE PERIOD OF TIME AS SET FORTH ABOVE, SHALL CONSTITUTE FULFILLMENT

OF ALL LIABILITY OF THE COMPANY TO THE PURCHASER WHETHER BASED ON CONTRACT, NEGLIGENCE, OR OTHERWISE.

THE COMPANY SHALL NOT BE LIABLE FOR INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES SUCH AS, BUT NOT LIMITED TO:

DAMAGE TO OR LOSS OF OTHER PROPERTY OR EQUIPMENT, LOSS OF USE OF EQUIPMENT, FACILITIES OR SERVICE, LOSS OF PROFIT

OR SALES, COST OF PURCHASES OR REPLACEMENT GOODS, CLAIMS OF CUSTOMERS OF THE PURCHASER, FAILURE TO WARN AND/

OR INSTRUCT, LOSS OF OTHER PRODUCTS, OR COSTS OF ENVIRONMENTAL REMEDIATION, OR DIMINUTION IN PROPERTY VALUE.

THE REMEDIES OF THE PURCHASER SET FORTH HEREIN ARE EXCLUSIVE, AND THE LIABILITY OF THE COMPANY SHALL NOT, EXCEPT

AS EXPRESSLY PROVIDED HEREIN, EXCEED THE PRICE OF THE PRODUCTS UPON WHICH SUCH LIABILITY IS BASED. DAMAGES AS

SET FORTH IN THIS PARAGRAPH SHALL BE REASONABLY MITIGATED TO THE EXTENT POSSIBLE. THIS PARAGRAPH SHALL ALSO

APPLY TO ALL DAMAGES RESULTING FROM CONDITIONS SET FORTH IN SECTION III ABOVE AND (1) DEFECTS IN PRODUCT PROTO-

TYPES OR REPLACEMENT PART PROTOTYPES THAT HAVE NOT BEEN PUT INTO PRODUCTION, CIRCULATED AND SOLD BY THE COM-

PANY, AND/OR (2) DEFECTS THAT WERE NOT FOUND AT THE TIME OF SALE DUE TO SCIENTIFIC AND TECHNOLOGICAL REASONS.

This Limited Warranty gives you specific legal rights. You may have other rights, which vary according to the applicable laws and

regulations. Where any term of this warranty is prohibited by such laws, it shall be null and void, but the remainder of this war-

ranty shall remain in full force and effect.

DISCLAIMER: Any oral statements about the product made by the seller, the Company, the representatives or any other parties, do not constitute war-

ranties, shall not be relied upon by the user, and are not part of the contract for sale. Seller’s and the Company’s only obligation, and buyer’s only rem-

edy, shall be the replacement and/or repair by the Company of the product as described above. Before using, the user shall determine the suitability

of the product for his intended use, and user assumes all risk and liability whatsoever in connection therewith.

littlegiant.com

FRANÇAISFR

SÉRIE MODÈLE 6 & 8

Manuel du propriétaire

Pompes de puisard

Table des matières

CONSIGNES DE SÉCURITÉ - - - - - - - 18

INTRODUCTION - - - - - - - - - - - 20

DESCRIPTION DU PRODUIT - - - - - 20

INSTALLATION - - - - - - - - - - - - 21

INSTALLATION PHYSIQUE - - - - - 21

BRANCHEMENTS ÉLECTRIQUES - - - 23

TEST DE FONCTIONNEMENT - - - - - 25

ENTRETIEN - - - - - - - - - - - - - - 28

SERVICE PÉRIODIQUE - - - - - - - 28

DÉPANNAGE - - - - - - - - - - - - 29

PIÈCES DE RECHANGE - - - - - - - 30

GARANTIE LIMITÉE - - - - - - - - - - 31

CONSIGNES DE SÉCURITÉ

Messages d’avertissement

CONSIGNES DE SÉCURITÉ

Messages d’avertissement

Ce manuel comporte des précautions de sécurité et d’autres

informations importantes dans les formats suivants:

IMPORTANT: Identifie une information qui détermine le bon

assemblage et la bonne utilisation du produit.

REMARQUE: Identifie une information fournissant des

précisions utiles ou clarifiant un point.

Ce symbole alerte l’utilisateur de la présence d’une

tension électrique dangereuse dans le produit

susceptible d’entraîner des blessures ou un choc

électrique.

Ce symbole alerte l’utilisateur de la présence de surfaces

chaudes pouvant entraîner un incendie ou des blessures.

Avant de commencer

Cet équipement doit être installé et entretenu par des techniciens

qualifiés capables de choisir et d’utiliser les outils, les

équipements et les procédures appropriés. Le non-respect des

codes électriques et codes de plomberie local et national et des

recommandations de Franklin Electric pourrait mener à une

électrocution ou un incendie, une mauvaise performance ou une

défaillance de l’équipement.

Renseignez-vous sur l’application, les limitations et les risques

potentiels du produit. Lisez et suivez attentivement les

instructions pour éviter toute blessure ou tout dommage

matériel. Ne démontez pas et ne réparez pas l’appareil si ces

opérations ne sont pas décrites dans le présent manuel.

Consulter la plaque signalétique du produit pour obtenir des

instructions et des spécifications de fonctionnement supplémen-

taires.

Le non-respect des procédures d’installation ou d’utilisation et de

tous les codes en vigueur peut entraîner les risques suivants:

Indique une situation dangereuse imminente

qui, si elle n’est pas évitée, entraînera la mort

ou des blessures graves.

Indique une situation dangereuse potentielle

qui, si elle n’est pas évitée, peut entraîner des

blessures graves ou la mort.

Indique une situation dangereuse potentielle

qui, si elle n’est pas évitée, peut entraîner des

blessures légères à modérées.

Indique une situation dangereuse potentielle

qui, si elle n’est pas évitée, peut entraîner

l’endommagement de l’équipement ou

d’autres dégâts matériels.

Risque de mort, de blessure corporelle

ou de dommage

matériel en raison

d’une explosion, d’un incendie ou d’une

électrocution.

• Ne pas utiliser pour pomper des liquides inflammables ou

explosifs comme l’essence, le mazout, le kérosène, etc.

• Ne pas utiliser dans une atmosphère explosive ou un

emplacement dangereux selon le Code national de l’élec-

tricité, ANSI/NFPA70.

• Ne pas manipuler une pompe ou un moteur de pompe

avec les mains mouillées ou debout sur une surface

humide ou mouillée, ou dans de l’eau.

• Lorsqu’une pompe est en mode de fonctionnement, ne

pas toucher le moteur, les tuyaux ou l’eau tant que l’unité

n’a pas été débranchée ou déconnectée électriquement.

• Si le dispositif de coupure du circuit d’alimentation se

situe hors site, le verrouiller en position ouverte et le

consigner afin d’empêcher toute mise sous tension

inopinée.

• Si le panneau du disjoncteur n’est pas accessible, con-

tacter la compagnie d’électricité afin que le courant soit

coupé.

CONSIGNES DE SÉCURITÉ

Avant de commencer

1 Sauf modèles CB

Cet appareil contient des tensions

élevées susceptibles d’entraîner par

choc électrique des blessures graves ou

la mort.

• Pour réduire le risque de choc électrique, débranchez l’ali-

mentation avant de travailler sur le système ou autour de

celui-ci. Plusieurs interrupteurs d’isolement peuvent être

nécessaires pour décharger l’équipement avant de

procéder à son entretien.

• Assurez-vous que cette pompe est raccordée à un circuit

doté d’un disjoncteur différentiel de fu-ite à la terre

(DDFT).

• Raccorder le système de pompe en respectant la tension

indiquée.

• La pompe a été évaluée pour être utilisée avec de l’eau

uniquement. La pompe doit être utilisée uniquement avec

des liquides compatibles avec les matériaux de ses com-

posants. Si la pompe est utilisée avec des liquides incom-

patibles avec les composants de la pompe, le liquide peut

provoquer une défaillance du système d'isolation élec-

trique entraînant un choc électrique.

Risque de dommages à la pompe ou d’autres

équipements.

• Ne pas utiliser la pompe pour pomper de l’eau de mer, des

boissons, de l’acide, des solutions chimiques ou tout autre

liquide qui favoriserait la corrosion, ce qui pourrait

endommager la pompe.

• Ne pas faire tourner la pompe à sec. Pour obtenir un

refroidissement optimal et pour prolonger la durée de vie

de la pompe, le niveau de liquide pompé doit

normalement dépasser le dessus du boîtier de la pompe.

• Cette pompe n’est pas prévue pour être utilisée dans un

étang.

Risque de blessure, de choc

électrique ou de dégâts matériels.

• Cet équipement ne doit pas être utilisé par des enfants ou

des personnes aux capacités physiques, sensorielles ou

cognitives réduites, ou par des personnes n’ayant pas

l’expérience ou l’expertise appropriée, sauf si ces per-

sonnes sont supervisées ou ont reçu des instructions à cet

effet. Les enfants ne doivent pas utiliser l’équipement ni

jouer avec l’appareil ou dans sa proximité immédiate.

• L’équipement peut démarrer automatiquement. Débran-

chez toujours le cordon d’alimentation de la pompe et

cou-pez l’alimentation électrique avant d’entretenir la

pompe ou l’interrupteur. Consignez l’équipement avant

de procéder à son entretien.

• Une pompe inopérante ou défectueuse pourrait entraîner

une inondation, des blessures corporelles ou des dom-

mages matériels.

• Dans les applications où des dommages matériels et/ou

des blessures corporelles pourraient découler du non-

fonctionnement ou d’une fuite de la pompe en raison de

pannes de courant, d’une obstruction de la ligne d’évacu-

ation ou de toute autre raison, un système de sauvegarde

automatique et/ou une alarme doivent être installés.

• Ne pas faire fonctionner la pompe à sec. En cas de

fonctionnement à sec, la température à la surface de la

pompe augmentera à un niveau susceptible de causer des

brûlures cutanées en cas de contact et entraînera de

graves dommages à votre pompe.

• Ne pas graisser le moteur. Le carter moteur de la pompe

est scellé et renferme une huile diélectrique de qualité

supérieure pour la transmission de chaleur et la lubrifica-

tion à vie. L’utilisation d’autres huiles peut causer de

graves électrocutions et/ou des dommages permanents

de la pompe.

• L’utilisation de cet équipement nécessite les instructions

d’installation et d’utilisation détaillées fournies dans le

présent manuel à utiliser avec ce produit. Lisez le manuel

intégralement avant de procéder à l’installation et à l’utilisa-

tion du produit. L’utilisateur final doit recevoir et conserver le

manuel pour consultation ultérieure.

• Garder les étiquettes de sécurité propres et en bon état.

• Garder la zone de travail propre, bien éclairée et dégagée.

• Porter des lunettes de sécurité lors de l’installation ou de

l’entretien de la pompe.

• Ne pas porter de vêtements amples, de bijoux ou tout

autre accessoire qui pourrait se prendre dans les pièces

mobiles de l’équipement. Attacher les cheveux longs et

retirer les bijoux.

INTRODUCTION

Description du produit

INTRODUCTION

Description du produit

Cette pompe immergée est prévue pour être utilisée dans des bassins ou des stations de relèvement. Elle peut être

utilisée pour pomper de l’eau claire. N’utilisez pas cette pompe dans des applications où des effluents (eaux

ménagères), des eaux usées ou d’autres débris (gravier, sable, débris flottants, etc.), des abrasifs ou des matières cor-

rosives sont présents. Ces pompes sont disponibles dans des versions automatique et manuelle.

Ces produits ont été testés, inspectés et emballés avec soin afin de garantir une livraison et un fonctionnement en

toute sécurité. Veuillez examiner soigneusement votre pompe afin de vous assurer qu’elle n’a pas été endommagée

lors du transport. Si elle a été endommagée, veuillez contacter le point de ven-te. Il vous aidera à remplacer ou à

réparer le produit, le cas échéant.

Le moteur de la pompe est doté d’un disjoncteur thermique à réenclenchement automatique et peut redémarrer

inopinément. Le déclenchement du disjoncteur thermique indique une surcharge ou une surchauffe du moteur, qui

peut être causée par des problèmes d’application comme l’obstruction d’une roue de la pompe, le blocage de l’inter-

rupteur en position ON, le fonctionnement à sec de la pompe, le blocage de la pompe par de l’air, le fonctionnement

de la pompe en cycles courts, une tension d’alimentation trop élevée ou trop basse, ou, éventuellement, une pompe,

un moteur, des rou-lements ou un joint ayant atteint la fin de sa/leur vie utile.

Modèles

* Il ne s’agit pas de pompes à double tension.

Il est possible de convertir les pompes manuelles au mode automatique en installant un dispositif de contrôle du

niveau de liquide séparé tel qu’un ensemble d’interrupteur à distance RS-5.

Débits

Modèle ch PSI Tension Méthode d’activation de la pompe

6-CIA 1/3 7.8 115 ou 230* Automatique avec interrupteur à diaphragme

6-CIM 1/3 7.8 115 ou 230* Manuelle

6-CIM-R 1/3 7.8 115 Manuelle

6-CIM-RS 1/3 7.8 115 Automatique avec interrupteur à diaphragme à distance

6-CIA-RFS 1/3 7.8 115 Automatique avec interrupteur à flotteur à distance

8-CIA 4/10 9.9 115 Automatique avec interrupteur à diaphragme

8-CBA 4/10 9.9 115 Automatique avec interrupteur à diaphragme

8-CIM 4/10 9.9 115 Manuelle

8-CBM 4/10 9.9 115 Manuelle

Gallons/Litres par minute

En hauteur: (Hauteur

de charge)

5 pi

1.5 m

10 pi

3 m

15 pi

4.5 m

Éteindre

Série6 46 / 174 29 / 110 12.5 / 47.3

18 pi

5.5 m

Série8 54 / 204 42 / 159 26 / 98

22.9 pi

7 m

La page charge ...

Little GIANT 6-CIM Le manuel du propriétaire

Marque: Little GIANT

Modèle: 6-CIM

Catégorie: Pompes à eau

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: Little GIANT 6-CIM Owner's manual
español: Little GIANT 6-CIM El manual del propietario

Little GIANT 6-CIM Le manuel du propriétaire

Little GIANT 6-CIM Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents