Hitachi Koki WH12DAF2 - 12V Cordless 1/4" Impact Driver Manuel utilisateur

INSTRUCTIONS DE SECURITE ET MODE D’EMPLOI

AVERTISSEMENT

Une utilisation INCORRECTE OU DANGEREUSE de cet outil motorisé peut entraîner la

mort ou de sérieuses blessures corporelles!

Ce mode d’emploi contient d’importantes informations à propos de la sécurité de ce

produit. Prière de lire et de comprendre ce mode d’emploi AVANT d’utiliser l’outil

motorisé. Garder ce mode d’emploi à la disponibilité des autres utilisateurs et

propriétaires avant qu’ils utilisent l’outil motorisé. Ce mode d’emploi doit être conservé

dans un endroit sûr.

SAFETY INSTRUCTIONS AND INSTRUCTION MANUAL

WARNING

IMPROPER OR UNSAFE use of this power tool can result in death or serious bodily

injury!

This manual contains important information about product safety. Please read and

understand this manual BEFORE operating the power tool. Please keep this manual

available for other users and owners before they use the power tool. This manual should

be stored in safe place.

INSTRUCCIONES DE SEGURIDAD Y MANUAL DE INSTRUCCIONES

ADVERTENCIA

¡La utilización INAPROPIADA O PELIGROSA de esta herramienta eléctrica puede resultar

en lesiones de gravedad o la muerte!

Este manual contiene información importante sobre la seguridad del producto. Lea y

comprenda este manual ANTES de utilizar la herramienta eléctrica. Guarde este manual

para que puedan leerlo otras personas antes de utilizar la herramienta eléctrica. Este

manual debe ser guardado en un lugar seguro.

Model Variable speed Cordless Impact Driver

Modèle Visseuse à percussion à batterie

Modelo Atornilladores de impacto a batería

WH 12DAF2

2

IMPORTANT SAFETY INFORMATION ................ 3

MEANINGS OF SIGNAL WORDS ........................ 3

SAFETY ...................................................................... 4

GENERAL SAFETY RULES – FOR ALL BATTERY

OPERATED TOOLS ........................................ 4

SPECIFIC SAFETY RULES .................................... 6

IMPORTANT SAFETY INSTRUCTIONS FOR USE

OF THE CORDLESS IMPACT DRIVER........... 7

IMPORTANT SAFETY INSTRUCTIONS FOR

BATTERY CHARGER...................................... 7

IMPORTANT SAFETY INSTRUCTIONS

FOR USE OF THE BATTERY AND

BATTERY CHARGER...................................... 8

FUNCTIONAL DESCRIPTION.................................. 10

MODEL................................................................. 10

NAME OF PARTS ................................................ 10

SPECIFICATIONS ................................................ 11

ASSEMBLY AND OPERATION ............................... 12

APPLICATIONS ................................................... 12

REMOVAL AND INSTALLATION METHOD OF

BATTERY ...................................................... 12

CHARGING METHOD ......................................... 12

BEFORE USE ....................................................... 14

OPERATION......................................................... 14

OPERATIONAL CAUTIONS ................................ 17

MAINTENANCE AND INSPECTION ....................... 19

ACCESSORIES ......................................................... 21

STANDARD ACCESSORIES ............................... 21

OPTIONAL ACCESSORIES ................................. 21

PARTS LIST.............................................................. 68

CONTENTS

English

Page Page

INFORMATIONS IMPORTANTES

DE SÉCURITÉ ............................................... 24

SIGNIFICATION DES MOTS

D’AVERTISSEMENT .................................... 24

SECURITE ................................................................ 25

REGLES GENERALE DE SECURITE – POUR TOUS

LES OUTILS FONCTIONNANT SUR

BATTERIE ..................................................... 25

REGLES DE SECURITE SPECIFIQUES ............... 27

CONSIGNES DE SÉCURITÉ IMPORTANTES

POUR L'UTILISATION DU VISSEUSE À

PERCUSSION À BATTERIE ......................... 28

CONSIGNES DE SÉCURITÉ IMPORTANTES

POUR LE CHARGEUR DE BATTERIE .......... 28

CONSIGNES DE SÉCURITÉ IMPORTANTES

POUR L’UTILISATION DE LA BATTERIE ET

DU CHARGEUR DE BATTERIE .................... 29

DESCRIPTION FONCTIONNELLE ........................... 31

MODELE .............................................................. 31

NOM DES PARTIES ............................................ 31

SPECIFICATIONS ................................................ 32

ASSEMBLAGE ET FONCTIONNEMENT ................ 33

UTILISATIONS .................................................... 33

MÉTHODE DE RETRAIT ET D’INSTALLATION

DE LA BATTERIE .......................................... 33

MÉTHODE DE RECHARGE ................................. 33

AVANT L’UTILISATION ...................................... 35

UTILISATION ....................................................... 35

PRECAUTIONS D'UTILISATION ........................ 39

ENTRETIEN ET INSPECTION .................................. 41

ACCESSOIRES ......................................................... 43

ACCESSOIRES STANDARD ............................... 43

ACCESSOIRES EN OPTION................................ 43

LISTA DES PIÉCES .................................................. 68

Page Page

IINFORMACIÓN IMPORTANTE SOBRE

SEGURIDAD ................................................. 46

SIGNIFICADO DE LAS PALABRAS DE

SEÑALIZACIÓN............................................ 46

SEGURIDAD............................................................. 47

NORMAS GENERALES DE SEGURIDAD – PARA

TODAS LAS HERRAMIENTAS

ALIMENTADAS CON BATERÍA................... 47

NORMAS ESPECÍFICOS DE SEGURIDAD ......... 49

INSTRUCCIONES IMPORTANTES PARA LA

UTILIZACIÓN DEL ATORNILLADORES DE

IMPACTO A BATERÍA .................................. 50

INSTRUCCIONES IMPORTANTES DE

SEGURIDAD PARA EL CARGADOR DE

BATERÍAS ............................................... 50

INSTRUCCIONES IMPORTANTES DE

SEGURIDAD PARA LA BATERÍA Y EL

CARGADOR DE BATERÍAS ......................... 51

DESCRIPCIÓN FUNCIONAL.................................... 53

MODELO .............................................................. 53

NOMENCLATURA............................................... 53

ESPECIFICACIONES............................................ 54

MONTAJE Y OPERACIÓN ...................................... 55

APLICACIONES ................................................... 55

MÉTODO DE EXTRACCIÓN E INSTALACIÓN

DE LA BATERÍA............................................ 55

MÉTODO DE CARGA .......................................... 55

ANTES DE LA UTILIZACIÓN .............................. 57

OPERACIÓN ........................................................ 57

PRECAUCIONES OPERACIONALES .................. 61

MANTENIMIENTO E INSPECCIÓN ........................ 63

ACCESSOIRES ......................................................... 65

ACCESORIOS ESTÁNDAR ................................. 65

ACCESORIOS OPCIONALES .............................. 65

LISTA DE PIEZAS .................................................... 68

Página Página

TABLE DES MATIERES

ÍNDICE

Français

Español

English

3

IMPORTANT SAFETY INFORMATION

Read and understand all of the safety precautions, warnings and operating instructions in

the Instruction Manual before operating or maintaining this power tool.

Most accidents that result from power tool operation and maintenance are caused by the

failure to observe basic safety rules or precautions. An accident can often be avoided by

recognizing a potentially hazardous situation before it occurs, and by observing appropriate

safety procedures.

Basic safety precautions are outlined in the “SAFETY” section of this Instruction Manual

and in the sections which contain the operation and maintenance instructions.

Hazards that must be avoided to prevent bodily injury or machine damage are identified by

WARNINGS on the power tool and in this Instruction Manual.

NEVER use this power tool in a manner that has not been specifically recommended by

HITACHI.

MEANINGS OF SIGNAL WORDS

WARNING indicates a potentially hazardous situations which, if ignored, could result in

death or serious injury.

CAUTION indicates a potentially hazardous situations which, if not avoided, may result in

minor or moderate injury, or may cause machine damage.

NOTE emphasizes essential information.

English

4

SAFETY

GENERAL SAFETY RULES – FOR ALL BATTERY OPERATED

TOOLS

WARNING: Read and understand all instructions.

Failure to follow all instructions listed below, may result in electric shock,

fire and/or serious personal injury.

SAVE THESE INSTRUCTIONS

1. Work Area

(1) Keep your work area clean and well lit. Cluttered benches and dark areas invite

accidents.

(2) Do not operate power tools in explosive atmospheres, such as in the presence of

flammable liquids, gases, or dust. Power tools create sparks which may ignite the

dust of fumes.

(3) Keep bystanders children, and visitors away while operating a power tool.

Distractions can cause you to lose control.

2. Electrical Safety

(1) A battery operated tool with integral batteries or a separate battery pack must be

recharged only with the specified charger for the battery.

A charger that may be suitable for one type of battery may create a risk of fire when

used with another battery.

(2) Use battery operated tool only with specifically designed battery pack.

Use of any other batteries may create a risk of fire.

3. Personal Safety

(1) Stay alert, watch what you are doing and use common sense when operating a

power tool. Do not use tool while tired or under the influence of drugs, alcohol, or

medication. A moment of inattention while operating power tools may result in

serious personal injury.

(2) Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep

your hair, clothing and gloves away from moving parts. Loose clothes, jewelry, or

long hair can be caught in moving parts.

(3) Avoid accidental starting. Be sure switch is off position before inserting battery.

Carrying tools with your finger on the switch or inserting the battery pack into a

tool with the switch on invites accidents.

(4) Remove adjusting keys or wrenches before turning the tool on. A wrench or a key

that is left attached to a rotating part of the tool may result in personal injury.

(5) Do not overreach. Keep proper footing and balance at all times. Proper footing and

balance enable better control of the tool in unexpected situations.

(6) Use safety equipment. Always wear eye protection. Dust mask, non-skid safety

shoes, hard hat, or hearing protection must be used for appropriate conditions.

English

5

4. Tool Use and Care

(1) Use clamps or other practical way to secure and support the workpiece to a stable

platform. Holding the work by hand or against your body is unstable and may lead

to loss of control.

(2) Do not force tool. Use the correct tool for your application. The correct tool will do

the job better and safer at the rate for which it is designed.

(3) Do not use tool if switch does not turn it on or off. Any tool that cannot be controlled

with the switch is dangerous and must be repaired.

(4) Disconnect battery pack from tool or place the switch in the locked or off position

before making any adjustments, changing accessories, or storing the tools. Such

preventive safety measures reduce the risk of starting the tool accidentally.

(5) Store idle tools out of reach of children and other untrained persons. Tools are

dangerous in the hands of untrained users.

(6) When battery pack is not in use, keep it away from other metal objects like: paper

clips, coins, keys, nails, screws, or other small metal objects that can make a

connection from one terminal to another.

Shorting the battery terminals together may cause sparks, burns, or a fire.

(7) Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained

tools, with sharp cutting edges are less likely to bind and are easier to control.

(8) Check for misalignment or binding of moving parts, breakage of parts, and any

other condition that may affect the tools operation. If damaged, have the tool

serviced before using. Many accidents are caused by poorly maintained tools.

(9) Use only accessories that are recommended by the manufacturer for your model.

Accessories that may be suitable for one tool, may become hazardous when used

on another tool.

5. Service

(1) Tool service must be performed only by qualified repair personnel. Service or

maintenance performed by unqualified personnel could result in a risk of injury.

(2) When servicing a tool, use only identical replacement parts. Follow instructions in

the Maintenance section of this manual. Use of unauthorized parts or failure to

follow Maintenance Instruction may create a risk of electric shock or injury.

WARNING:

Some dust created by power sanding, sawing, grinding, drilling, and other construction

activities contains chemicals known to the State of California to cause cancer, birth

defects or other reproductive harm. Some examples of these chemicals are:

● Lead from lead-based paints,

● Crystalline silica from bricks and cement and other masonry products, and

● Arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you do this type of

work. To reduce your exposure to these chemicals: work in a well ventilated area, and

work with approved safety equipment, such as those dust masks that are specially

designed to filter out microscopic particles.

English

6

SPECIFIC SAFETY RULES

1. Hold tools by insulated gripping surfaces when performing an operation where the

cutting tool may contact hidden wiring. Contact with a “live” wire will make exposed

metal parts of the tool “live” and shock the operator.

2. Never touch moving parts.

Never place your hands, fingers or other body parts near the tool’s moving parts.

3. Never operate without all guards in place.

Never operate this tool without all guards or safety features in place and in proper

working order. If maintenance or servicing requires the removal of a guard or safety

feature, be sure to replace the guard or safety feature before resuming operation of the

tool.

4. Use right tool.

Don’t force small tool or attachment to do the job of a heavy-duty tool.

Don’t use tool for purpose not intended —for example— don’t use circular saw for

cutting tree limbs or logs.

5. Never use a power tool for applications other than those specified.

Never use a power tool for applications other than those specified in the Instruction

Manual.

6. Handle tool correctly.

Operate the tool according to the instructions provided herein. Do not drop or throw

the tool. Never allow the tool to be operated by children, individuals unfamiliar with its

operation or unauthorized personnel.

7. Definitions for symbols

V .............................volts

---

............................direct current

n

o

............................no load speed

---/min ....................revolutions or reciprocation per minute

8. Keep all screws, bolts and covers tightly in place.

Keep all screws, bolts, and plates tightly mounted. Check their condition periodically.

9. Do not use power tools if the plastic housing or handle is cracked.

Cracks in the tool’s housing or handle can lead to electric shock. Such tools should not

be used until repaired.

10. Blades and accessories must be securely mounted to the tool.

Prevent potential injuries to youself or others. Blades, cutting implements and

accessories which have been mounted to the tool should be secure and tight.

11. Never use a tool which is defective or operating abnormally.

If the tool appears to be operating unusually, making strange noises, or otherwise

appears defective, stop using it immediately and arrange for repairs by a Hitachi

authorized service center.

12. Carefully handle power tools.

Should a power tool be dropped or struck against hard materials inadvertently, it may

be deformed, cracked, or damaged.

13. Do not wipe plastic parts with solvent.

Solvents such as gasoline, thinner benzine, carbon tetrachloride, and alcohol may

damage and crack plastic parts. Do not wipe them with such solvents.

Wipe plastic parts with a soft cloth lightly dampened with soapy water and dry

thoroughly.

English

7

IMPORTANT SAFETY INSTRUCTIONS FOR USE OF THE

CORDLESS IMPACT DRIVER

WARNING: Death or serious bodily injury could result from improper or unsafe use

of the cordless impact driver. To avoid these risks, follow these basic

safety instructions:

1. Never use this driver handle for any application other than those in this manual.

2. Never place hands or other body parts near the drill bit or chuck during operation.

Hold the impact driver by its handle only.

3. When working in high places, always make sure that ther is no one below before starting

to work.

4. Always wear eye and ear protection when you work.

5. Always install the driver bit securely. A loose bit is dangerous because it can come

loose while you are working.

6. Always use the driver bit that matches the screw size.

7. Always have the screw you are screwing in and this impact driver in a straight line.

Working with this impact driver at an angle to the screw can damage the screw head

and will not give the prescribed tightening torque.

IMPORTANT SAFETY INSTRUCTIONS

FOR BATTERY CHARGER

1. This manual contains important safety and operating instructions for battery charger

Model UC18YG.

2. Before using battery charger, read all instructions and cautionary markings on (1) battery

charger, (2) battery, and (3) product using battery.

3. To reduce risk of injury, charge HITACHI rechargeable battery type EB1214S. Other

type of batteries may burst causing personal injury and damage.

4. Do not expose battery charger to rain or snow.

5. Use of an attachment not recommended or sold by the battery charger manufacturmJ

may result in a risk of fire, electric shock, or injury to persons.

6. To reduce risk of damage to electric plug and cord, pull by plug when disconnecting

battery charger.

7. Make sure cord is located so that it will not be stepped on, tripped over, or otherwise

subjected to damage or stress.

8. An extension cord should not be used unless absolutely necessary. Use of improper

extension cord could result in a risk of fire and electric shock.

If extension cord must be used make sure:

a. That blades of extension cord are the same number, size, and shape as those of

plug on battery charger:

b. That extension cord is properly wired and in good electrical condition; and

c. That wire size is large enough for AC ampere rating of battery charger as specified

in Table 1.

English

8

* If the input rating of a battery charger is given in watts rather than in amperes, the

corresponding ampere rating is to be determined by dividing the wattage rating by the

voltage rating–for example:

9. Do not operate battery charger with damaged cord or plug-replace them immediately.

10. Do not operate battery charger if it has received a sharp blow, been dropped, or otherwise

damaged in any way; take it to a qualified serviceman.

11. Do not disassemble battery charger; take it to a qualified serviceman when service or

repair is required. Incorrect reassembly may result in a risk of electric shock or fire.

12. To reduce risk of electric shock, unplug charger from receptacle before attempting any

maintenance or cleaning. Removing the battery will not reduce this risk.

IMPORTANT SAFETY INSTRUCTIONS FOR USE OF THE

BATTERY AND BATTERY CHARGER

You must charge the battery before you can use the cordless impact driver. Before using

the model UC18YG battery charger, be sure to read all instructions and cautionary statements

on it, the battery and in this manual.

REMEMBER: USE ONLY HITACHI BATTERY TYPE EB1214S. OTHER TYPES OF BATTERIES

MAY BURST AND CAUSE INJURY!

Follow these instructions to avoid the risk of injury:

WARNING: Improper use of the battery or battery charger can lead to serious injury.

To avoid these injuries:

1. NEVER disassemble the battery.

2. NEVER incinerate the battery, even if it is damaged or is completely worn out. The

battery can explode in a fire.

3. NEVER short-circuit the battery.

4. NEVER insert any objects into the battery charger’s air vents. Electric shock or

damage to the battery charger may result.

Table 1

RECOMMENDED MINIMUM AWG SIZE FOR

EXTENSION CORDS FOR BATTERY CHARGERS

AC Input Rating Amperes* AWG Size of Cord

Equal to or but less Length of Cord, Feet (Meter)

greater than than 25 (7.5) 50 (15) 100 (30) 150 (45)

02 1818 18 16

23 1818 16 14

34 1818 16 14

1,250watts

125 volts

= 10 amperes

English

9

5. NEVER charge outdoors. Keep the battery away from direct sunlight and use only

where there is low humidity and good ventilation.

6. NEVER charge when the temperature is below 32°F (0°C) or above 104°F (40°C).

7. NEVER connect two battery chargers together.

8. NEVER insert foreign objects into the hole for the battery or the battery charger.

9. NEVER use a booster transformer when charging.

10. NEVER use an engine generator or DC power to charge.

11. NEVER store the battery or battery charger in places where the temperature may

reach or exceed 104°F (40°C).

12. ALWAYS operate charger on standard household electrical power (120 volts). Using

the charger on any other voltage may overheat and damage the charger.

13. ALWAYS wait at least 15 minutes between charges to avoid overheating the charger.

14. ALWAYS disconnect the power cord from its receptacle when the charger is not in

use.

SAVE THESE INSTRUCTIONS

AND

MAKE THEM AVAILABLE TO

OTHER USERS

AND

OWNERS OF THIS TOOL!

English

10

Fig. 1

FUNCTIONAL DESCRIPTION

NOTE: The information contained in this Instruction Manual is designed to assist you in

the safe operation and maintenance of the power tool.

NEVER operate, or attempt any maintenance on the tool unless you have first read

and understood all safety instructions contained in this manual.

Some illustrations in this Instruction Manual may show details or attachments that

differ from those on your own power tool.

MODEL

WH12DAF2: with charger (UC18YG) and case

NAME OF PARTS

1. Cordless Impact Driver

䡬 Battery

EB1214S

Latch

Nameplate

Terminal

hole

Nameplate

Switch trigger

Handle

Battery

Push button

Housing

Air vents

Hook

English

11

2. Battery Charger (UC18YG)

SPECIFICATIONS

1. Cordless Impact Driver

2. Battery Charger (UC18YG)

Fig. 2

Model WH12DAF2

No-load speed 0 – 2,500/min

Capacity 5/32" (4 mm) – 5/16" (8 mm) (Small screw)

3/16" (M5) – 15/32" (M12) (Ordinary bolt)

3/16" (M5) – 3/8" (M10) (High tension bolt)

Tightening Maximum 975 in-lbs

{110 N·m 1,120 kgf·cm}

torque Tightening is 15/32" (M12) high tension bolt, when fully charged

at 68°F (20°C) temp.

Tightening time: 3 sec.

Bit shank size 1/4" (6.35 mm) Hex.

Rechargeable EB1214S (1.4 Ah)

battery Ni-Cd battery, DC 12 V

Charging and discharging frequency: about 300

Weight 3.5 lbs (1.6 kg)

Input power source Single phase: AC120V 60Hz

Charging time Approx. 30min. (At a temperature of 68°F (20°C))

Charging voltage DC 12V

Charging current DC 2.6A

Weight 0.7 lbs (0.3 kg)

Battery installation hole

Pilot lamp

Cord

Plug

Nameplate

English

12

ASSEMBLY AND OPERATION

APPLICATIONS

䡬 Driving and removing of small screws, small bolts, etc.

REMOVAL AND INSTALLATION METHOD OF BATTERY

䡬 How to install the battery.

Align the battery with the groove in tool

handle and slip it into place.

Always insert it all the way until it locks

in place with a little click, If not, it may

accidentally fall out of the tool, causing

injury to you or someone around you.

(Fig. 3)

䡬 How to remove the battery.

Withdraw battery from the tool handle

while pressing the latch of the battery.

(Fig. 3)

CHARGING METHOD

NOTE: Before plugging into the receptacle, make sure the following points.

䡬 The power source voltage is stated on the nameplate.

䡬 The cord is not damaged.

WARNING: Do not charge at voltage higher than indicated on the nameplate.

If charged at voltage higher than indicated on the nameplate, the

charger will burn up.

1. Insert the plug of battery charger into the receptacle.

WARNING: Do not use the electrical cord if damaged. Have it

repaired immediately.

Fig. 3

Handle

Latch

Battery

Pull out

Insert

English

13

2. Insert the battery to the battery charger.

Insert the battery into the battery charger as shown

in Fig. 4. Make sure it contacts the bottom of the

battery charger.

3. Charging

䡬 When the battery is connected to the battery charger, charging will commence and the

pilot lamp will light on.

NOTE: If the pilot lamp dose not light, pull out the plug from the receptacle and check

if the battery is properly mounted.

䡬 In approx. 30 min., when the battery is fully charged, the pilot lamp will go out.

NOTE: The battery charging time becomes longer when a temperature is low or the

voltage of the power source is too low.

When the pilot lamp does not go off even if more than four hour has passed

after start of the charging, stop the charging and contact your HITACHI

AUTHORIZED SERVICE CENTER.

4. Disconnect battery charger from the receptacle.

CAUTION:

● Do not pull the plug out of the receptacle by pulling on the cord.

Make sure to grasp the plug when removing from receptacle to avoid damaging cord.

5. Remove the battery from the battery charger.

Supporting the battery charger with hand, pull out the battery from the battery charger.

CAUTION:

● When the battery charger has been continuosly used, the battery charger will be heated,

thus constituting the cause of the failures. Once the charging has been completed,

wait 15 minutes rest until the next charging.

● If the battery is recharged when it is warm due to battery use or exposure to sunlight,

the pilot lamp may not light.

The battery will not be recharged. In such a case, let the battery cool before charging.

Regarding electric discharge in case of new batteries, etc.

As the internal chemical substance of new batteries and batteries that have not been

Fig. 4

Pilot lamp

Battery

English

14

used for an extended period is not activated, the electric discharge might be low when

using them the first and second time. This is a temporary phenomenon, and normal

time required for recharging will be restored by recharging the batteries 2 – 3 times.

How to make the batteries perform longer.

(1) Recharge the batteries before they become completely exhausted.

When you feel that the power of the tool becomes weaker, stop using the tool and

recharge its battery. If you continue to use the tool and exhaust the electric current, the

battery may be damaged and its life will become shorter.

(2) Avoid recharging at high temperatures.

A rechargeable battery will be hot immediately after use. If such a battery is recharged

immediately after use, its internal chemical substance will deteriorate, and the battery

life will be shortened. Leave the battery and recharge it after it has cooled for a while.

BEFORE USE

Check the work area to make sure that it is clear of debris and clutter.

Clear the area of unnecessary personnel. Ensure that lighting and ventilation is adequate.

OPERATION

1. Using the light equipped hook

WARNING: When using the hook, pay sufficient attention so that the main

equipment does not fall. If the tool falls, there is a risk of accident.

CAUTION:

Do not attach the tip tool to the tool main unit when carrying the tool main unit with

the light equipped hook suspended from a waist belt.

Such action could result in injury.

The light equipped hook has the following two functions:

䡬 It can be used as a hook for suspending from a waist belt when required by the

nature of the work.

䡬 It can be used as an auxiliary light for such operations as tightening screws in a

dark place.

1.1 Using the hook

The hook can be installed on the right or left side

and the angle can be adjusted in 5 steps between

0° and 80°.

(1) Operating the hook

(a) Pull out the hook toward you in the direction

of arrow (A) and turn in the direction of arrow

(B). (Fig. 5)

(b) The angle can be adjusted in 5 steps (0°, 20°,

40°, 60°, 80°).

Hook

Fig. 5

(A)

(B)

5

4

3

2

1

English

15

Adjust the angle of the hook to the desired

position for use.

(2) Switching the hook position

CAUTION:

● If the tool falls, there is a risk that malfunction

and/or physical damage can occur. It is

recommended that you also use fall-preventing

wires, etc.

● Incomplete installation of the hook may result in

bodily injury when used.

(a) Securely hold the main unit and remove the

screw using a slotted head screwdriver or a

coin. (Fig. 6)

(b) Remove the hook and spring. (Fig. 7)

(c) Install the hook and spring on the other side

and securely fasten with screw. (Fig. 6)

NOTE:

Pay attention to the spring orientation. Install

the spring with larger diameter away from

you. (Fig. 8)

1.2 Using as an auxiliary light

(1) Press the switch to turn off the light.

If forgotten, the light will turn off automatically

after 15 minutes.

(2) The direction of the light can be adjusted within

the range of hook positions 1 - 5. (Fig. 9)

䡬 Lighting time

AAAA manganese batteries: approx. 15 hrs.

AAAA alkali batteries: approx. 30 hrs.

CAUTION:

Do not look directly into the light.

Such actions could result in eye injury.

1.3 Replacing the batteries

(1) Loosen the hook screw with a phillips-head

screwdriver (No. 1). (Fig. 10)

Remove the hook cover by pushing in the direction

of the arrow. (Fig. 11)

(2) Remove the old batteries and insert the new

batteries. Align with the hook indications and

position the plus (+) and minus (-) terminals

correctly. (Fig. 12)

(3) Align the indentation in the hook main body with

the protuberance of the hook cover, press the hook

cover in the direction opposite to that of the arrow

Fig. 6

Fig. 7

Spring

Hook

Fig. 10

Fig. 8

Fig. 9

Larger

diameter

Screw

Phillips - head

screwdriver

Hook

Loosen

Switch

Hook

3

English

16

shown in Fig. 11 and then tighten the screw.

Use commercially available AAAA batteries

(1.5 V).

NOTE:

Do not tighten the screw excessively. Such action

could strip the screw threads.

CAUTION:

● Failure to observe the following can result in

battery leakage, rust or malfunction.

Position the plus (+) and minus (-) terminals

correctly.

Replace both batteries at the same time. Do not

mix old and new batteries.

Remove exhausted batteries from the hook

immediately.

● Do not discard batteries together with normal

trash and do not throw batteries into fire.

● Store batteries out of the reach of children.

● Use batteries correctly in accordance with the

battery specifications and indications.

2. Installing the bit

Always follow the following procedure to install

driver bit. (Fig. 13)

(1) Pull the guide sleeve forward.

(2) Insert the bit into the hexagonal hole in the anvil.

(3) Release the guide sleeve and it returns to its

origianl position.

CAUTION

If the guide sleeve does not return to its original

position, then the bit is not installed properly.

3. Removing the bit

Please do the opposite point on the method of

installing bit.

4. Confirm that the battery is mounted correctly.

5. Check the rotational direction

The bit rotates clockwise (viewed from the rear

side) by pushing the R-side of the push button.

The L-side of the push button is pushed to turn

the bit counterclockwise. (See Fig. 14). (The

L

and

R

marks are engraved on the body.)

CAUTION

The push button can not be switched while the impact driver is turning. To switch the

push button, stop the impact driver, then set the push button.

Fig. 11

Fig. 12

Arrow

Hook cover

Hook main body

Protube-

rance

AAAA

batteries

Indentation

Protube-

rance

Inden-

tation

Hook cover

Fig. 13

R

L

PushPush

Push

button

Fig. 14

Driver

bit

Hexagonal

hole in the

anvil

Movement

Guide

sleeve

English

17

6. Switch operation

䡬 When the trigger switch is depressed, the tool rotates. When the trigger is released, the

tool stops.

䡬 The rotational speed can be controlled by varying the amount that the trigger switch is

pulled. Speed is low when the trigger switch is pulled slightly and increases as the

trigger switch is pulled more.

NOTE:A buzzing noise is produced when the motor is about to rotate; this is only a noise,

not a machine failure.

7. Tightening and loosening screws

Install the bit that matches the screw, line up the bit in the grooves of the head of the

screw, then tighten it.

Push the impact driver just enough to keep the bit fitting the head of the screw.

CAUTION

䢇 Applying the impact driver for too long tightens the screw too much and can break it.

䢇 Tightening a screw with the impact driver at an angle to that screw can damage the

head of the screw and the proper force will not be transmitted to the screw.

Tighten with this impact driver lined up straight with the screw.

8. Number of screw tightenings possible

Please refer to the table below for the number of screw tightenings possible with one

charge.

<WH12DAF2> (EB1214S)

These values may vary slightly, according to surrounding temperature and battery

characteristics.

OPERATIONAL CAUTIONS

1. Resting the unit after continuous work

After use for continuous bolt-tightening work, rest the unit for 15 minutes or so when

replacing the battery. The temperature of the motor, switch, etc., will rise if the work is

started again immediately after battery replacement, eventually resulting in burnout.

CAUTION:

Do not touch the hammer case, as it gets very hot during continuous work.

Screw used No. of tightenings

Wood screw 5/32" × 2"

Appro. 190

(Soft wood) (ø4 × 50)

Machine screw

Appro. 500

5/16" x 5/8" (M8 × 16)

English

18

Tightening torque

kgf·cm

N·m

5/16"×1-3/6"

(in-lbs) (M8×30)

kgf·cm

N·m

3/8"×1-3/6"

(in-lbs) (M10×30)

kgf·cm

N·m

15/32"×1-3/4"

(in-lbs) (M12×45)

100

80

60

40

20

0

0 123

1000

800

600

400

200

0

(868)

(694)

(521)

(347)

(174)

100

80

60

40

20

0

0 123

1000

800

600

400

200

(868)

(694)

(521)

(347)

(174)

High tension bolt

Ordinary bolt

High tension bolt

100

80

60

40

20

0

0 123

1000

800

600

400

200

0

1201200

(868)

(694)

(521)

(347)

(174)

(1042)

High tension bolt

Ordinary bolt

Fig. 16

Bolt

Nut

Steel plate

thickness t

Explanation of strength grade:

4 — Yield point of bolt: 45,500 psi (32 kgf/mm

2

)

8 — Pulling strength of bolt: 56,900 psi (40 kgf/mm

2

)

*The following bolt is used.

Ordinary bolt: Strength grade 4.8

High

tension

bolt: Hardness division 12.9

(

)

Washer

2. Cautions on use of the speed control switch

This switch has a built-in, electronic circuit which steplessly varies the rotation speed.

Consequently, when the switch trigger is pulled only slightly (low speed rotation) and

the motor is stopped while continuously driving in screws, the components of the

electronic circuit parts may overheat and be damaged.

3. Tightening torque

Refer to Fig. 15 for the tightening torque of bolts (according to size), under the conditions

shown in Fig. 16. Please use this example as a general reference, as tightening torque

will vary according to tightening conditions.

NOTE: 䡬 If a long striking time is used, screws will be strongly tightened. This may cause

the screw to break, or may damage the end of the bit.

䡬 If the unit is held at an angle to the screw being tightened, the head of the

screw may be damaged, or the specified torque may not be transmitted to the

screw. Always keep the unit and the screw being tightened in a straight line.

4. Use a tightening time suitable for the screw

The appropriate torque for a screw differs according to the material and size of the

screw, and the material being screwed etc., so please use a tightening time suitable for

the screw. In particular, if a long tightening time is used in the case of screws smaller

than 5/16” (8 mm), there is a danger of the screw breaking, so please confirm the

tightening time and the tightening torque beforehand.

Tightening time: sec

(Steel plate thickness

t = 3/8" (10 mm))

Tightening time: sec

(Steel plate thickness

t = 3/8" (10 mm))

Tightening time: sec

(Steel plate thickness

t = 1" (25 mm))

Fig. 15

English

19

MAINTENANCE AND INSPECTION

CAUTION:

Pull out battery before doing any inspection or maintenance.

1. Checking the condition of the bit.

The bits should be checked regularly. If worn or broken bits can slip or decrease the

efficiency of the motor and burn it out.

Replace worn bits with new ones.

CAUTION:

If you use a driver bit of which point is worn or broken, it will be dangerous since it

slips. So replace it with a new one.

2. Check the Screws

Loose screws are dangerous. Regularly inspect them and make sure they are tight.

CAUTION:

Using this power tool with loosened screws is extremely dangerous.

3. Check for Dust

Dust may be removed with a soft cloth or a cloth dampened with soapy water.

Do not use bleach, chlorine, gasoline or thinner, for they may damage the plastics.

4. Disposal of the exhausted battery.

WARNING: Do not dispose of the exhausted battery. The battery must explode if it

is incinerated. The product that you have purchased contains a

rechargeable battery. The battery is recyclable. At the end of it’s useful

life, under various state and local laws, it may be illegal to dispose of

this battery into the municipal waste stream. Check with your local

solid waste officials for details in your area for recycling options or

proper disposal.

5. Storage

Storing in a place below 104°F (40°C) and out of the reach of children.

6. Service and repairs

All quality power tools will eventually require servicing or replacement of parts because

of wear from normal use. To assure that only authorized replacement parts will be

used, all service and repairs must be performed by a HITACHI AUTHORIZED SERVICE

CENTER, ONLY.

7. Service parts list

CAUTION:

Repair, modification and inspection of Hitachi Power Tools must be carried out by an

Hitachi Authorized Service Center.

English

20

This Parts List will be helpful if presented with the tool to the Hitachi Authorized

Service Center when requesting repair or other maintenance. In the operation and

maintenance of power tools, the safety regulations and standards prescribed in each

country must be observed.

MODIFICATIONS:

Hitachi Power Tools are constantly being improved and modified to incorporate the latest

technological advancements.

Accordingly, some parts (i.e. code numbers and/or design) may be changed without prior

notice.

La page charge ...

Hitachi Koki WH12DAF2 - 12V Cordless 1/4" Impact Driver Manuel utilisateur

Ce manuel convient également à

Hitachi Koki WH12DAF2 - 12V Cordless 1/4" Impact Driver Manuel utilisateur

dans d''autres langues

Autres documents