LG LW6017R Le manuel du propriétaire

Taper
Le manuel du propriétaire
www.lg.com
ENGLISH
Copyright © 2017-2018 LG Electronics Inc. All Rights Reserved.
OWNER’S MANUAL
AIR
CONDITIONER
Read this owners manual thoroughly before operating the appliance
and keep it handy for reference at all times.
TYPE: WINDOW
MFL70960702
Rev.01_113018
OWNER’S MANUAL
AIR
CONDITIONER
LW6017R
FRANÇAIS
2
TABLE OF CONTENTS
TABLE OF CONTENTS
11 Window Requirements
11 Location
11 Clearance
11 Preparation of Chassis
12 Unit Installation
14 OPERATION
14 Control Panel and Remote Control
15 Wireless Remote Control
16 Additional Features
9 INSTALLATION
9 Electrical Data
10 Installation Overview
3 SAFETY INSTRUCTIONS
3 IMPORTANT SAFETY INSTRUCTIONS
8 PRODUCT OVERVIEW
8 Exterior Parts
8 Interior Parts
17 MAINTENANCE
17 Air Filter
18 TROUBLESHOOTING
18 Before Calling for Service
18 Normal Sounds You May Hear
21 WARRANTY
ENGLISH
3
SAFETY INSTRUCTIONS
SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USE
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always
read and follow all safety messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or injure you and others.
All safety messages will follow the safety alert symbol and either the word WARNING or
CAUTION.
These words mean:
WARNING
You may be killed or seriously injured if you do not follow instructions.
CAUTION
You may be injured or cause damage to the product if you do not follow instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce
the chance of injury, and tell you what may happen if the instructions are not followed.
IMPORTANT SAFETY INSTRUCTIONS
WARNING
injury to persons when using this product, follow basic precautions,
including the following:
INSTALLATION
Before use, the appliance must be properly installed as described in this manual.
Contact the authorized service technician for repair or maintenance of this unit.
Contact the installer for installation of this unit.
The air conditioner is not intended for use by young children or invalids without supervision.
Young children should be supervised to ensure that they do not play with the air conditioner.
4
SAFETY INSTRUCTIONS
When the power cord is to be replaced, replacement work shall be performed by authorized
personnel only using only genuine replacement parts.
Installation work must be performed in accordance with the National Electric Code by qualied
and authorized personnel only.
Connect to a properly rated, protected, and sized power circuit to avoid electrical overload.
Always plug into a grounded outlet.
Do not under any circumstances, cut or remove the third (ground) prong from the power cord.
When installing or moving the appliance, be careful not to pinch, crush, or damage the power
cord.
Plug in the power plug properly.
Do not modify or extend the power cord.
Do not start/stop operation by plugging/unplugging the power cord.
If the cord/plug is damaged, have it replaced by an authorized service person using authorized
replacement parts.
Use a dedicated circuit.
Do not disassemble or modify the product.
Adhere to all industry recommended safety procedures including the use of long-sleeved gloves
and safety glasses.
Use care when unpacking and installing. The edges of the product may be sharp.
Disconnect the power cord or circuit breaker before installing or servicing the appliance.
Keep packaging materials out of the reach of children. These materials can pose a suffocation
risk to children.
Store and install the product where it will not be exposed to temperatures below freezing or
exposed to outdoor weather conditions.
Do not store or use gasoline or other ammable vapors and liquids in the vicinity of this or any
other appliance.
OPERATION
Use this appliance only for its intended purpose.
Never attempt to operate this appliance if it is damaged, malfunctioning, partially disassembled,
or has missing or broken parts, including a damaged cord or plug.
Repair or immediately replace all power cords that have become frayed or otherwise damaged.
Do not use a cord that shows cracks or abrasion damage along its length or at either end.
Do not run cord under carpets or mats where it could be stepped on and damaged.
Keep the cord out from under heavy objects like tables or chairs.
Do not place the power cord near a heat source.
Do not use an adaptor or plug the product into a shared outlet.
Do not tamper with controls.
If you detect a strange sound, a chemical or burning smell, or smoke coming from the appliance,
unplug it immediately, and contact an LG Electronics Customer Information Center.
Never unplug the appliance by pulling on the power cord. Always grip the plug rmly and pull
straight out from the outlet.
Do not grasp the power cord or touch the appliance controls with wet hands.
ENGLISH
5
SAFETY INSTRUCTIONS
If water enters the product, turn off the power at the main circuit, then unplug the product and call
for service.
If the product has been submerged, contact an LG Electronics Customer Information Center for
instructions before resuming use.
Unplug the product when unused for long periods.
Unplug the product before cleaning.
In the event of a gas leak (propane gas, etc.) do not operate this or any other appliance. Open a
window or door to ventilate the area immediately.
This appliance is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have been
given supervision or instruction concerning the use of the appliance by a person responsible for
their safety.
The interior of the product must only be cleaned by an authorized service center or a dealer.
Do not use solvent-based detergent on the product. Doing so can cause corrosion or damage,
product failure, electrical shock, or re.
GROUNDING INSTRUCTIONS
The power cord of this appliance is equipped with a three-prong (grounding) plug. Use this with
a standard three-slot (grounding) wall power outlet to minimize the hazard of electric shock. The
customer should have the wall receptacle and circuit checked by a qualied electrician to make
sure the receptacle is properly grounded. DO NOT CUT OR REMOVE THE THIRD (GROUND)
PRONG FROM THE POWER PLUG.
- Situations when the appliance will be disconnected occasionally; Because of potential safety
hazards, we strongly discourage the use of an adapter plug. However, if you wish to use an
adapter, a TEMPORARY CONNECTION may be made. Use UL-listed adapter, available from
most local hardware stores.
The large slot in the adapter must be aligned with the large slot in the receptacle to assure a
proper polarity connection.
Attaching the adapter ground terminal to the wall receptacle cover screw does not ground the
appliance unless the cover screw is metal, and not insulated, and the wall receptacle is grounded
through the house wiring. The customer should have the circuit checked by a qualied electrician
to make sure the receptacle is properly grounded.
Disconnect the power cord from the adapter, using one hand on each. Otherwise, the adapter
ground terminal might break. Do not use the appliance with a broken adapter plug.
- Situations when the appliance will be disconnected often; Do not use an adapter plug in these
situations. Unplugging the power cord frequently can lead to an eventual breakage of the
ground terminal. The wall power outlet should be replaced by a three-slot (grounding) outlet
instead.
6
SAFETY INSTRUCTIONS
CAUTION
To reduce the risk of minor or moderate injury to persons, malfunction, or
damage to the product or property when using this product, follow basic
precautions, including the following:
INSTALLATION
Take care when installing the product that exhaust or condensation does not damage nearby
property.
Follow installation instructions exactly to avoid excessive vibration or water leakage.
OPERATION
This appliance is not intended for use as a precision refrigeration system. Do not use it for special
purposes such as maintaining pets, food, precision machinery, or art objects.
When installing or moving the appliance, be careful not to pinch, crush, or damage the power
cord.
Make sure the air inlet and outlet are free from obstructions.
Use a soft cloth to clean the appliance. Do not use waxes, thinners, or harsh detergents.
Do not step on or place heavy objects on top of the appliance.
Do not drink water drained from the appliance.
are used simultaneously.
Remove the batteries if the remote control is not to be used for an extended period of time.
Never mix different types of batteries, or old and new batteries for the remote control.
f with clean water.
consult a doctor.
Do not recharge or disassemble the batteries.
MAINTENANCE
Never use strong cleaning agents or solvents when cleaning the air conditioner or spray water.
Use a smooth cloth.
Do not expose people, animals, or plants to the cold or hot wind from the air conditioner for
extended periods of time.
ENGLISH
7
SAFETY INSTRUCTIONS
REFRIGERANT (FOR R32 ONLY)
WARNING
Do not use means to accelerate the defrosting process or to clean, other than those
recommended by the manufacturer.
The appliance shall be stored in a room without continuously operating ignition sources (for
example: open ames, an operating gas appliance or an operating electric heater).
Do not pierce or burn. Be aware that ammable refrigerants may not contain an odor.
CAUTION
This unit contains ammable refrigerant and has special safety precautions not normally
associated with older units. Please follow all precautions and advisories.
- Use caution while handling and prevent damage to unit. Do not put any holes into product for
any reason. This can cause damage to product and prevent unit from cooling.
- Maintenance and cleaning of unit should be performed by trained personnel. Failure to properly
clean unit can result in damage to the refrigeration system and or the electrical system.
- Make certain that all the air circulation/ventilation openings are free from obstruction.
- Service should only be performed by technicians properly trained and certied in the use of
ammable refrigerants. Any service performed by unauthorized servicers/individuals will void all
warranties.
- When storing the appliance, do not put in a room with any open ame appliances, such as gas
water heaters or furnaces. Also keep away from electric heaters. Damaged units should be
repaired before storage.
SAVE THESE INSTRUCTIONS
8
PRODUCT OVERVIEW
PRODUCT OVERVIEW
Exterior Parts Interior Parts
1
Evaporator
2
Air Guide
3
4
Compressor
5
6
Condenser
Base Pan
Power Cord
3
4
5
2
1
6
1
Control Panel
2
Remote Controller
3
Air Filter
4
5
Cabinet
6
7
Front Grille
Air Outlet
5
4
7
1
3
2
6
ENGLISH
9
INSTALLATION
INSTALLATION
Electrical Data
Power cord may include a current interrupter
device. TEST and RESET buttons are provided
on the plug case. The device should be tested on
TEST button
and then the RESET button. If the TEST button
does not trip or if the RESET button will not stay
engaged, discontinue use of the air conditioner
WARNING
This appliance should be installed in
accordance with the National Electrical
Code.
Use of extension cords could cause serious
injury or death.
- Do not use an extension cord with this
window air conditioner.
- Do not use surge protectors or multi-outlet
adapters with this window air conditioner.
Never push the TEST button during
operation. Doing so can damage the plug.
- Do not remove, modify, or immerse this
plug. If this device trips, the cause should
be corrected before further use.
CAUTION
The conductors inside this cord are
surrounded by shields, which monitor
leakage current. These shields are not
grounded. Periodically examine the cord
for any damage. Do not use this product
in the event the shields become exposed.
Avoid shock hazard. This unit cannot be
user-serviced. Do not open the tamper-
resistant sealed portion. All warranties and
performance will be voided. This unit is not
intended to be used as an ON/OFF switch.
Use Wall Receptacle Power Supply
Use 15 A, time
delay fuse or 15 A,
circuit breaker.
Standard 120 V, 3-wire
grounding receptacle rated
15 A / 120 VAC / 60 Hz
for 120 V
RESET
TEST
10
INSTALLATION
Installation Overview
Accessories
Phillips-head
screwdriver
Flat-blade screwdriver Adjustable wrench Level
Tape measure Cutting knife Scissors Pencil
Right Guide
panel
Left Guide
panel
Sash seal
(Non-adhesive
backed)
Seal strip
(Adhesive backed)
L bracket (3)
Upper Guide
Type 'A' Screws
(14)
Type 'B' Screws
(2)
Tools Needed
Type 'C' Screws
(2)
ENGLISH
11
INSTALLATION
Window Requirements
This unit is designed for installation in standard
double hung windows with actual opening
widths from 21" to 35".
The top and bottom window sashes must open
12" from the bottom of the upper sash to the
inside sill.
21" to 35"
(533mm to 889mm)
12"
(305mm)
min
NOTE
This prodcut is a WINDOW AIR CONDITIONER.
As such, a standard single-hung or double-hung
window is required for proper installation.
No-window installations, including using sleeves,
holes in walls, and other installations are not
recommended.
Preparation of Chassis
1
1
The bottom of the cabinet should be
30” ~ 60” above the ground.
2
The outside of cabinet must extend outward
for at least 1/2”.
3
There should be no obstacles such as a
fence or wall within 20” from the back of the
cabinet.
4
All side louvers of the cabinet must remain
exposed to the outside of the structure.
Clearance
Proper clearance enhances the cooling efficiency
of the unit and prevents heat radiation of the
condenser.
Location
Install the air conditioner where the sunlight does
not shine directly on the unit.
Insert the guide panels into the guides of
the air conditioner. Fasten the curtains to
the unit with screws (Type A).
(Without Frame Curtain)
Offset
Sill
Exterior
Stool
Interior Wall
Fence
Awning
Cooled Air
Heat
About
Over
Radiation
Type A
Type A
Type A
(533mm to 889mm)
21″ to 35″
(305mm)
12″
min
17 2/7″(439mm) min
1/2″ (12.7mm)
1/2″ to 1 1/4″
( )
20″ (508mm)
(762mm~1524mm)
30″ ~60″
2
Cut the adhesive-backed seal strip to the
window width. Remove the backing from
the seal strip and attach the seal strip to
the underside of the bottom window.
Seal Strip
12
INSTALLATION
4
Install the L bracket behind the inner
window sill, with short side of bracket as
shown. Use the 2 screws (Type A)
provided.
The bracket helps to hold unit securely in
place. Be sure to place bracket edge flush
against back of inner sill.
NOTE
When the air conditioner drops into the
L bracket, the air conditioner will be
centered in window opening.
NOTE
L Bracket
Outer Sill
Inner Sill
Center Line
Inside
Outside
7 1/2″
(191mm)
7 1/2″
(191mm)
3
Locating unit in window.
window and mark center line on the
Open the
center of the inner sill.
Room Side
Inner Sill
Center Line
Unit Installation
1
CAUTION
During the following step, hold unit firmly until
window sash is lowered to top channel behind
side panel frames. Personal injury or property
damage may result if unit falls from window.
WINDOW FRAME
SEAL
CENTER LINE
UPPER GUIDE
L BRACKET
BOTTOM GUIDE
Carefully lift the air conditioner and slide it
into the open window. Makesure the bottom
guide of the air conditioner drops into the
notches of the L bracket.
While steadying the air conditioner, carefully
bring the window sash down behind the
upper guide of the air conditioner. When the
air conditioner is properly installed, it should
tilt slightly down at the back. If it is set
correctly in the window, it will hang lower in
the back automatically. If it does not, there
is aproblem with the installation.
ABOUT
"4/1
ENGLISH
13
INSTALLATION
NOTE
See the 'Electrical Data' section for
information on attaching the power cord
to an electrical outlet.
3
Cut the sash seal to the window width. Stuff
the sash seal between the glass and the
window to prevent air and insects from
getting into the room. Fasten the L bracket
using a screw(Type A).
2
Extend the guide panels to fill the window
opening using 2 screws (Type B) and 2
screws (Type C) to secure them.
L BRACKET
SASH SEAL
Type A
Type B
Type C
14
OPERATION
.
OPERATION
Control Panel and Remote Control
Remote Control
1
Power
2
Fan Speed
Use to set the fan speed to Low (F1), MED
(F2), High (F3).
3
ON/OFF Timer
Delay ON - When the air conditioner is off,
it can be set to automatically turn on from
1 to 24 hours at its previous mode and fan
settings.
Delay OFF - When the air conditioner is on,
it can be set to automatically turn on from
1 to 24 hours.
NOTE
Each press of the Timer button advances
the timer by 1 hour. After the last press
the display returns to the temperature
setting.
Operation starts when this buttom is pressed
and stops when you press the buttom again.
Cool
Fan - Fan circulates air but the compressor
does not run. Use the FAN button to set
the desired fan speed.
Dry - Dry mode is used to remove humidity
from the room without additional cooling.
Once the set temperature is reached, the
compressor and circulation fan turns off.
Fan speed is pre-set and cannot be
adjusted.
1
4
2
5
3
- Compressor runs and cools the
room. Use the and FAN buttons to
set the desired temperature and circulation
fan speed.
Energy Saver - The fan stops when the
compressor stops cooling. Approximately
every 3 minutes the fan will turn on and
check the room air temperature if cooling
is needed.
4 3 2
1
7
6
5
4
Operation Mode Selector
Push the Mode button to rotate between
Energy Saver / Cool / Fan / Dry.
ENGLISH
15
OPERATION
5
Temperature Control
The thermostat monitors room temperature
to maintain the desired temperature. The
thermostat can be set between 60 °F–86 °F
(16 °C–30 °C). Press
or arrows to
increase or decrease temperature setting.
6
Remote Control Sensor
Clean Filter
The Clean Filter LED lights up to notify you
that the lter needs to be cleaned. After
cleaning the lter, press Temp
and
together on the control panel to turn off the
Clean Filter light.
NOTE
The lter reset must be done using the
control panel, not the remote control.
This feature is a reminder to clean the air
lter for more efcient operation. The LED
light turns on after 250 hours of operation.
7
NOTE
Auto Restart: If the air conditioner turns off due
to a power outage, it will restart automatically
once the power is restored, with the same
settings as were set before the unit turned off.
Energy Saver: The unit defaults to the Energy
Saver mode each time the unit is switched on
except in Fan mode or when power is restored
after an electrical power outage.
The remote control will not function properly if
the AC infrared sensor is exposed to direct light
or if there are obstacles between the remote
controller and the air conditioner
.
Wireless Remote Control
Inserting Battery
1
Remove the cover from the back of the
remote controller.
2
Insert one battery.
3
Reattach the cover.
NOTE
Be sure that the (+) and (-) directions
are correct.
Be sure that the battery is new.
Do not use a rechargeable battery.
In order to prevent discharge, remove the
battery from the remote control if the air
conditioner is not going to be used for an
extended period of time.
Keep the remote control away from
extremely hot or humid places.
To maintain optimal operation of the remote
control, the remote sensor should not be
exposed to direct sunlight.
16
OPERATION
Air Direction
Adjusting the air direction using the horizontal
air deflector control.
Using the control tabs, the air flow can be
directed to the left, right, straight ahead, or any
combination of these directions.
Additional Features
Slinger Fan
This air conditioner is equipped with a slinger
fan. (See drawing, below.)
The fan has an outer ring that runs in the water
the collects in the base pan if it gets deep. That
condensate is then picked up by the fan and
expelled through the condenser, making the air
conditioner more efficient.
Ring
ENGLISH
17
MAINTENANCE
2
40 °C (104 °F).
3
Gently shake the excess water from the
Cleaning the Air Conditioner
Wipe the front grille and inlet grille with a cloth
dampened in a mild detergent solution.
Wash the cabinet with mild soap or detergent
and lukewarm water, then polish using liquid
appliance wax.
MAINTENANCE
WARNING
Before cleaning or performing maintenance,
disconnect the power supply and wait until
the fan stops.
Air Filter
if cleaning is necessary. Trapped particles in the
cooling capacity and causing an accumulation of
frost on the evaporator.
Cleaning the Air Filter
1
HOW TO REMOVE THE FRONT
GRILLE
Remove the screws securing the Front Grille.
Push the grille up from the bottom and pull
the top of the grille away from the case as
the top tabs lift out of their slots.
NOTE
condenser coils (outside of unit) should be
checked periodically and cleaned if clogged
with soot or dirt from outside air.
For repair and maintenance, contact an
Authorized Service Center. See the warranty
page for details or call 1-888-LG-CANADA
(542 2623).
Have your model number and serial number
available. They should be written on page 22
of this manual.
18
TROUBLESHOOTING
TROUBLESHOOTING
Before Calling for Service
The appliance is equipped with an automatic error-monitoring system to detect and diagnose problems
at an early stage. If the appliance does not function properly or does not function at all, check the
following before you call for service.
Normal Sounds You May Hear
1
High Pitched Chatter
2
Sound of Rushing Air
At the front of the unit, you may hear the sound of rushing air being moved by the fan.
3
Gurgle/Hiss
Gurgling or hissing noise may be heard due to refrigerant passing through evaporator during
normal operation.
4
Vibration
Unit may vibrate and make noise because of poor wall or window construction or incorrect
installation.
5
Pinging or Swishing
Droplets of water hitting condenser during normal operation may cause pinging or swishing
sounds.
1
2
3
5
4
ENGLISH
19
TROUBLESHOOTING
Problem Possible Cause Solutions
Air conditioner
does not start.
The air conditioner is unplugged.
Make sure the air conditioner plug
is pushed completely into the outlet.
The fuse is blown/circuit breaker
is tripped.
Check the house fuse/circuit
breaker box and replace the fuse or
reset the breaker.
Power failure.
If power failure occurs, turn the
mode control to off. When power is
restored, wait 3 minutes to restart
the air conditioner to prevent
tripping of the compressor overload.
The current interrupter device is
tripped.
Press the RESET button located
on the power cord plug. If the
RESET button will not stay
engaged, discontinue use of the air
conditioner and contact a qualied
service technician.
Air conditioner
does not cool as it
should.
Airow is restricted.
Make sure there are no curtains,
blinds, or furniture blocking the front
of the air conditioner.
The temp control may not be set
correctly.
Set the desired temperature to
a level lower than the current
temperature.
The air lter is dirty.
Clean the lter at least every 2
weeks. See the 'MAINTENANCE'
section.
The room may have been hot.
When the air conditioner is rst
turned on, you need to allow time
for the room to cool down.
Cold air is escaping.
Check for open furnace oor
registers and cold air returns.
Cooling coils have iced up.
See 'Air conditioner freezing up'
below.
Air conditioner
freezing up.
The cooling coils are iced over.
Ice may block the air ow and
obstruct the air conditioner from
properly cooling the room. Set the
mode control at High Fan or High
Cool.
Water drips
outside.
Hot, humid weather. This is normal.
20
TROUBLESHOOTING
Problem Possible Cause Solutions
Water drips
indoors.
The air conditioner is not tilted to
the outside.
For proper water disposal, make
sure the air conditioner slants
slightly from the cabinet front to the
rear.
Water collects in
base pan.
Moisture removed from air and
drains into base pan.
This is normal for a short period in
areas with little humidity; normal for
a longer period in very humid areas.
Air conditioner
turns on and off
rapidly.
Outside temperature extremely
hot.
Refer to installation instructions or
check with installer.
Noise when unit is
cooling.
Air movement sound.
This is normal. If too loud, set to
lower FAN setting.
Window vibration - poor
installation.
Refer to installation instructions or
check with installer.
Remote sensing
deactivating
prematurely.
Remote control not located
within range.
Place remote control within 20 feet
& 120° radius of the front of the
unit.
Remote control signal
obstructed.
Remove obstruction.
Room too cold. Set temperature too low. Increase set temperature.
NOTE
You can refer to the Energy Star program in detail at www.energystar.gov.
If you see "CH" in the display, please call 1-888-LG-CANADA(542 2623).
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52

LG LW6017R Le manuel du propriétaire

Taper
Le manuel du propriétaire

dans d''autres langues