Wacker Neuson PG3A Manuel utilisateur

Taper
Manuel utilisateur
Operator’s Manual
Notice d'emploi
Pump
Pompe
PG3A
Type PG3A
Document 5000184898
Date
0819
Version
14
Language EN-FR
5000184898
Copyright notice
© Copyright 2019 by Wacker Neuson Production Americas LLC
All rights, including copying and distribution rights, are reserved.
This publication may be photocopied by the original purchaser of the
machine. Any other type of reproduction is prohibited without express
written permission from Wacker Neuson Production Americas LLC.
Any type of reproduction or distribution not authorized by Wacker
Neuson Production Americas LLC represents an infringement of valid
copyrights. Violators will be prosecuted.
Trademarks
All trademarks referenced in this manual are the property of their
respective owners.
Manufacturer
Wacker Neuson Production Americas LLC
N92W15000 Anthony Avenue
Menomonee Falls, WI 53051 U.S.A.
Tel: (262) 255-0500 · Fax: (262) 255-0550 · Tel: (800) 770-0957
www.wackerneuson.com
Original instructions
This Operators Manual presents the original instructions. The original
language of this Operator’s Manual is American English.
PG 3A Foreword
wc_tx001328gb.fm 3
Foreword
SAVE THESE INSTRUCTIONS—This manual contains important instructions for
the machine models below. These instructions have been written expressly by
Wacker Neuson Production Americas LLC and must be followed during installation,
operation, and maintenance of the machines.
Machine
documentation
From this point forward in this documentation, Wacker Neuson Production
Americas L
LC will be referred to as Wacker Neuson.
Keep a copy of the Operator’s Manual with the machine at all times.
Use the separate Parts Book supplied with the machine to order replacement
parts.
If you are missing any of these documents, please contact Wacker Neuson to
o
rder a replacement or visit www.wacke
rneuson.com.
When ordering parts or requesting service information, be prepared to provide
th
e machine model number, item number, revision number, and serial number.
Expectations
for
information in
this manual
This manual provides information and procedures to safely operate and main-
tain the above Wacker Neuson model(s). For your own safety and to reduce the
risk
of injury, carefully read, understand, and observe all instructions
described
in this manual.
Wacker Neuson expressly reserves the right to make technical modifications,
even without notice, which improve the performance or safety standards of its
mach
ines.
The information contained in this manual is based on machines manufactured
u
p until the time of publication. Wacker Neuson reserves the right to chang
e
a
ny portion of this information without notice.
The illustrations, parts, and procedures in this manual refer to Wacker Neuson
fa
ctory-installed components. Your machine may vary depending on th
e
re
quirements of your specific region.
CALIFORNIA
Proposition
65 Warning
Combustion exhaust, some of its constituents, and certain vehicle components
contain or emit chemicals known to the State of California to cause cancer and
birth defects or other reproductive harm.
Laws
pertaining to
spark
arresters
NOTICE: State Health Safety Codes and Public Resources Codes specify that in
certain locations spark arresters be used on internal combustion engines that use
hydrocarbon fuels. A spark arrester is a device designed to prevent accidental dis-
charge of sparks or flames from the engine exhaust. Spark arresters are qualified
and rated by the United States Forest Service for this purpose. In order to comply
with local laws regarding spark arresters, consult the engine distributor or the local
Health and Safety Administrator.
Machine Item Number
PG 3A 0007659
PG 3A I 0009055
Foreword PG 3A
4 wc_tx001328gb.fm
Manufacturers
approval
This manual contains references to approved parts, attachments, and modifica-
tions. The following definitions apply:
Approved parts or attachments are those either manufactured or provided by
W
acker Neuso
n.
Approved modifications are those performed by an authorized Wacker Neu-
son service center according to written instructions published by Wacker Neu-
son.
Unapproved parts, attachments, and modifications are those that do not
meet
the approved criteria.
Unapproved parts, attachments, or modifications may have the following conse-
quences:
Serious injury hazards to the operator and persons in the work area
Permanent damage to the machine which will not be covered under warranty
Contact your Wacker Neuson dealer immediately if you have questions abo
ut
approved or
unapproved parts, attachments, or modifications.
2018_CE_PG3_PG3A_en.fm
EC Declaration of Conformity
Manufacturer
Wacker Neuson Production Americas LLC, N92W15000 Anthony Avenue,
Menomonee Falls, Wisconsin USA
Product
Product
Product category
Product function
Item number
Measured sound power level
Guaranteed sound power level
PG3A
Water Pump Units
To p um p fl ui d
5000009055
102 dB(A)
105 dB(A)
Conformity Assessment Procedure
According to ANNEX V
Notified Body
N/A
Directives and Standards
We hereby declare that this product meets and complies with the relevant regulations and
requirements of the following directives and standards:
2000/14/EC, 2006/42/EC, 2014/30/EU
Authorized Person for Technical Documents
Robert Raethsel, Wacker Neuson Produktion GmbH & Co. KG, Wackerstrasse 6,
85084 Reichertshofen, Germany
Menomonee Falls, WI, USA,
Travis Pound
Manager, Product Engineering
For Wacker Neuson
Original Declaration of Conformity
Keith Herr
Vice President and Managing Director
For Wacker Neuson
Jeff Volden
Director, Product Engineering
For Wacker Neuson
wc_bo5000184874_12TOC.fm 7
Table of ContentsPG 2A
Foreword 3
EC Declaration of Conformity 5
1 Safety Information 9
1.1 Signal Words Used in this Manual ....................................................... 9
1.2 Machine Description and Intended Use ............................................. 10
1.3 Safety Guidelines for Operating the Machine ..................................... 11
1.4 Operator Safety while Using Internal Combustion Engines ............... 13
1.5 Service Safety .................................................................................... 14
2 Labels 15
2.1 Label Locations .................................................................................. 15
2.2 Label Meanings .................................................................................. 16
3 Lifting and Transporting 18
4 Maintenance 19
4.1 Maintaining the Emission Control System .......................................... 19
4.2 Periodic Maintenance Schedule ......................................................... 19
4.3 Cleaning the Pump ............................................................................. 20
4.4 Adjusting the Impeller Clearance ....................................................... 21
4.5 Replacing the Mechanical Seal .......................................................... 22
4.6 Spark Plug .......................................................................................... 23
4.7 Servicing the Air Cleaner .................................................................... 24
4.8 Engine Oil ........................................................................................... 25
4.9 Cleaning the Sediment Cup (Honda) ................................................. 26
4.10 Adjusting the Carburetor .................................................................... 27
4.11 Adjusting the Idle Speed .................................................................... 27
4.12 Long-Term Storage ............................................................................ 28
5 Operation 29
5.1 Preparing the Machine for First Use ................................................... 29
5.2 Recommended Fuel ........................................................................... 29
5.3 Before Starting ................................................................................... 30
5.4 Starting ............................................................................................... 31
5.5 Stopping ............................................................................................. 31
5.6 Operation ............................................................................................ 32
8 wc_bo5000184874_12TOC.fm
Table of Contents PG 2A
5.7 Hoses and Clamps ..............................................................................32
5.8 Emergency Shutdown Procedure ........................................................33
6 Troubleshooting 34
7 Technical Data 35
7.1 Engine .................................................................................................35
7.2 Machine ...............................................................................................36
7.3 Sound Measurements .........................................................................36
7.4 Dimensions ..........................................................................................37
8 Emission Control Systems
Information and Warranty—Gasoline 38
8.1 Emission Control Systems Warranty Statement .................................38
9 AEM Safety Manual 40
wc_si000069gb.fm
9
PG 2A / 3A Safety Information
1 Safety Information
1.1 Signal Words Used in this Manual
This manual contains DANGER, WARNING, CAUTION, NOTICE, and NOTE
signal words which must be followed to reduce the possibility of personal injury,
damage to the equipment, or improper service.
NOTICE: Used without the safety alert symbol, NOTICE indicates a situation
which, if not avoided, could result in property damage.
Note: A Note contains additional information important to a procedure.
This is the safety alert symbol. It is used to alert you to potential personal hazards.
f Obey all safety messages that follow this symbol.
DANGER
DANGER indicates a hazardous situation which, if not avoided, will result in death
or serious injury.
f To avoid death or serious injury from this type of hazard, obey all safety
messages that follow this signal word.
WARNING
WARNING indicates a hazardous situation which, if not avoided, could result in
death or serious injury.
f To avoid possible death or serious injury from this type of hazard, obey all safety
messages that follow this signal word.
CAUTION
CAUTION indicates a hazardous situation which, if not avoided, could result in
minor or moderate injury.
f To avoid possible minor or moderate injury from this type of hazard, obey all
safety messages that follow this signal word.
wc_si000069gb.fm
10
Safety Information PG 2A / 3A
1.2 Machine Description and Intended Use
This machine is a centrifugal dewatering pump. The Wacker Neuson Dewatering
Pump consists of a tubular steel frame surrounding a gasoline engine, a fuel tank,
and an impeller pump with ports for water suction and discharge. The engine
rotates the impeller during operation. Waste water is drawn into the pump through
the suction port and expelled through the discharge port. The operator connects
hoses to the pump and routes them so that water and solids are drained from the
work area and discharged into an appropriate location.
This machine is intended to be used for general de-watering applications. This
machine is intended for the pumping of clear water, or water containing solids up to
the size stated within the product specifications, and up to the flow, head and
suction lift limits also stated within the product specifications.
This machine has been designed and built strictly for the intended use described
above. Using the machine for any other purpose could permanently damage the
machine or seriously injure the operator or other persons in the area. Machine
damage caused by misuse is not covered under warranty.
The following are some examples of misuse:
Pumping flammable, explosive, or corrosive fluids
Pumping hot or volatile fluids that result in pump cavitation
Operating the pump outside of product specifications due to incorrect diameter
hose
s, incorrect length hoses, other inlet or outlet
restrictions, or excessive
suction
lift or head
Using the machine as a ladder, support, or work surface
Using the machine to carry or transport passengers or equipment
Operating the machine outside of factory specifications
Operating the machine in a manner inconsistent with all warnings found on the
machine and in the Operators Manual.
This machine has been designed and built in accordance with the latest global
safety standards. It has been carefully engineered to eliminate hazards as far as
practicable and to increase operator safety through protective guards and labeling.
However, some risks may remain even after protective measures have been taken.
They are called residual risks. On this machine, they may include exposure to:
Heat, noise, exhaust, and carbon monoxide from the engine
Fire hazards from improper refueling techniques
Fuel and its fumes
Personal injury from improper lifting techniques
Projectile hazard from discharge
Crushing hazards from a tipping or falling pump
To protect yourself and others, make sure you thoroughly read and understand the
safety information presented in this manual before operating the machine.
wc_si000069gb.fm
11
PG 2A / 3A Safety Information
1.3 Safety Guidelines for Operating the Machine
Familiarity and proper training are required for the safe operation of the machine.
Machines operated improperly or by untrained personnel can be hazardous. Read
the operating instructions contained in this manual and the engine manual, and
familiarize yourself with the location and proper use of all controls. Inexperienced
operators should receive instruction from someone familiar with the machine
before being allowed to operate it.
Operator
qualifications
Only trained personnel are permitted to start, operate, and shut down the machine.
They also must meet the following qualifications:
have received instruction on how to properly use the machine
are familiar with required safety devices
The machine must not be accessed or operated by:
children
people impaired by alcohol or drugs
Personal
Protective
Equipment
(PPE)
Wear the following Personal Protective Equipment (PPE) while operating this
machine:
Close-fitting work clothes that do not hinder movement
Safety glasses with side shields
Hearing protection
Safety-toed footwear
Do not allow anyone to operate this equipment without proper training. People
operating this equipment must be familiar with the risks and hazards associated
with it.
Do not touch the engine or muffler while the engine is on or immediately after it
has been turned off. These areas get hot and may cause burns.
Do not use accessories or attachments that are not recommended by Wacker
Neuson. Damage to equipment and injury to the user may result.
Do not pump volatile, flammable, or low flash point fluids. These fluids could
ignite or explode.
Do not pump corrosive chemicals or water containing toxic substances. These
fluids could create serious health and environmental hazards. Contact local
authorities for assistance.
Do not open the priming plug when the pump is hot. Do not loosen or remove
inlet or discharge hose fittings when the pump is hot. Hot water inside could be
pressurized much like the radiator on an automobile. Allow the pump to cool to
the touch before loosening the plug and before loosening or removing the inlet
or discharge hose fittings.
Do not open pump housing cover while pump is operating, or start pump with
the cover off. The rotating impeller inside the pump can cut or sever objects
caught in it.
Do not block or restrict flow from inlet line or discharge line. Remove kinks from
discharge line before starting pump. Operation with a blocked inlet line or
discharge line can cause water inside pump to overheat.
Read, understand, and follow procedures in the Operator’s Manual before
attempting to operate the machine.
WARNING
wc_si000069gb.fm
12
Safety Information PG 2A / 3A
Be sure operator is familiar with proper safety precautions and operation
techniques before using machine.
Be sure the machine is on a firm, level surface and will not tip, roll, slide, or fall
while operating.
Close fuel valve on engines equipped with one when machine is not being
operated.
Store the machine properly when it is not being used. The machine should be
stored in a clean, dry location out of the reach of children.
wc_si000069gb.fm
13
PG 2A / 3A Safety Information
1.4 Operator Safety while Using Internal Combustion Engines
Operating
safety
When operating the pump:
Keep the area around exhaust pipe free of flammable materials.
Check the fuel lines and the fuel tank for leaks and cracks before starting the
engine.
When operating the pump:
Do not smoke while operating the machine.
Do not run the machine if fuel leaks are present or the fuel lines are loose.
Do not run the engine near sparks or open flames.
Do not touch the engine or muffler while the engine is running or immediately
after it has been turned off.
Do not operate a machine when its fuel cap is loose or missing.
Do not start the engine if fuel has spilled or a fuel odor is present. Move the
machine away from the spill and wipe the machine dry before starting.
Refueling
safety
When refueling the engine:
Clean up any spilled fuel immediately.
Refill the fuel tank in a well-ventilated area.
Replace the fuel tank cap after refueling.
When refueling the engine:
Do not smoke.
Do not refuel a hot or running engine.
Do not refuel the engine near sparks or open flames.
Do not refuel if the machine is positioned in a truck fitted with a plastic bed liner.
Static electricity can ignite the fuel or fuel vapors.
WARNING
Internal combustion engines present special hazards during operation and fueling.
Failure to follow the warnings and safety standards could result in severe injury or
death.
f Read and follow the warning instructions in the engine owner’s manual and the
safety guidelines below.
DANGER
Asphyxiation hazard. Using a pump indoors CAN KILL YOU IN MINUTES. Pump
exhaust contains carbon monoxide. This is a poison you cannot see or smell.
f NEVER use this pump inside a home or garage, EVEN IF doors and windows
are open. Only use OUTSIDE and far away from windows, doors, and vents.
f NEVER use a pump inside an enclosed area, such as a tunnel or a trench,
unless adequate ventilation is provided through such items as exhaust fans or
hoses.
wc_si000069gb.fm
14
Safety Information PG 2A / 3A
1.5 Service Safety
A poorly maintained machine can become a safety hazard! In order for the
machine to operate safely and properly over a long period of time, periodic
maintenance and occasional repairs are necessary.
Personal
Protective
Equipment
(PPE)
Wear the following Personal Protective Equipment (PPE) while servicing or
maintaining this machine:
Close-fitting work clothes that do not hinder movement
Safety glasses with side shields
Hearing protection
Safety-toed footwear
In addition, before servicing or maintaining the machine:
Tie back long hair.
Remove all jewelry (including rings).
Do not attempt to clean or service the machine while it is running. Rotating parts
can cause severe injury.
Do not crank a flooded engine with the spark plug removed on gasoline-
powered engines. Fuel trapped in the cylinder will squirt out the spark plug
opening.
Do not test for spark on gasoline-powered engines if the engine is flooded or the
smell of gasoline is present. A stray spark could ignite the fumes.
Do not use gasoline or other types of fuels or flammable solvents to clean parts,
especially in enclosed areas. Fumes from fuels and solvents can become
explosive.
Keep the area around the muffler free of debris such as leaves, paper, cartons,
etc. A hot muffler could ignite the debris and start a fire.
Replace worn or damaged components with spare parts designed and
approved by Wacker Neuson.
When replacement parts are required for this machine, use only Wacker
Neuson replacement parts or those parts equivalent to the original in all types of
specifications, such as physical dimensions, type, strength, and material.
Disconnect the spark plug on machines equipped with gasoline engines, before
servicing, to avoid accidental start-up.
WARNING
PG 3A Labels
wc_si000519gb.fm 15
2 Labels
2.1 Label Locations
wc_gr000833
A
C
D
E
G, H
F
B
Labels PG 3A
16 wc_si000519gb.fm
2.2 Label Meanings
A
Only use OUTSIDE and far away from windows, doors,
and vents.
B
WARNING
Hot surface
C
CAUTION
Read and understand the supplied Operator’s Manual
before operating this machine. Failure to do so
increases the risk of injury to yourself and others.
D
WARNING
Pressurized contents. Do not open when hot!
E
Impeller rotation.
STOPSTOP
178715178715
wc_gr014566
wc_gr014563
wc_gr014565
wc_gr014564
PG 3A Labels
wc_si000519gb.fm 17
F
Guaranteed sound power level in db(A)
G
A nameplate listing the model number, item number,
revision number, and serial number is attached to each
unit. Please record the information found on this name-
plate so it will be available should the nameplate
become lost or damaged. When ordering parts or
requesting service information, you will always be asked
to specify the model number, item number, revision
number, and serial number of the unit.
wc_tx001379gb.fm
18
Lifting and Transporting PG 2A / 3A
3 Lifting and Transporting
Lifting the
machine
This pump is heavy enough to cause injury if proper lifting techniques are not used.
Observe the following guidelines when lifting the pump.
Do not attempt to lift the pump unassisted. Use appropriate lifting equipment
such as slings, chains, hooks, ramps, or jacks.
Make sure lifting equipment is attached securely and has enough weight-
bearing capacity to lift or hold the pump safely.
Remain aware of the location of other people nearby when lifting the pump.
Transporting
the machine
Observe the following guidelines when transporting the pump to and from the job
site.
Drain the fuel tank before transporting the pump.
Ensure that the pump is securely strapped down in the transport vehicle to
prevent it from sliding or tipping.
Do not refuel the pump in or on the transport vehicle. Move the pump to its
operating location and then fill the fuel tank.
wc_tx000178gb.fm
19
PG 2A / 3A Maintenance
4 Maintenance
4.1 Maintaining the Emission Control System
Normal maintenance, replacement or repair of emission control devices and
systems may be performed by any repair establishment or individual; however,
warranty repairs must be performed by a dealer/service center authorized by the
engine manufacturer. See the supplied engine owner’s manual for the applicable
emission warranty information.
4.2 Periodic Maintenance Schedule
The table below lists basic machine maintenance. Tasks designated with check
marks may be performed by the operator. Tasks designated with square bullet
points require special training and equipment.
Daily
before
starting
After
first
20 hrs.
Every
50
hrs.
Every
100
hrs.
Every
300
hrs.
Check fuel level.
3
Check engine oil level.
3
Inspect air cleaner element.
Replace as needed.
3
Check external hardware.
3
Inspect hoses and housing for leaks.
3
Clean air cleaner element.
Change engine oil.

Clean cooling system.
Check and clean spark plug.
Clean sediment cup.
Check and adjust valve clearance.
Check and adjust impeller clearance.
wc_tx000178gb.fm
20
Maintenance PG 2A / 3A
4.3 Cleaning the Pump
After pumping water containing a large amount of dirt or debris, clean out inside of
pump housing.
1. Remove drain plug (b) from pump housing and drain any water left in pump.
2. Loosen the four knobs holding the pump cover (a) and remove cover.
3. Clean out dirt and debris. Inspect impeller and volute insert for wear.
The impeller may develop sharp edges. Use care when cleaning around impeller to
avoid getting cut.
WARNING
w c _ g r 0 0 0 8 3 7
=
>
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96

Wacker Neuson PG3A Manuel utilisateur

Taper
Manuel utilisateur

dans d''autres langues