Wacker Neuson PG2A Manuel utilisateur

Operator’s Manual

Notice d'emploi

Pump

Pompe

PG2A

Type PG2A

Document 5000184868

Date

0819

Version

14

Language EN-FR

5000184868

Copyright notice

All rights, including copying and distribution rights, are reserved.

This publication may be photocopied by the original purchaser of the

machine. Any other type of reproduction is prohibited without express

written permission from Wacker Neuson Production Americas LLC.

Any type of reproduction or distribution not authorized by Wacker

Neuson Production Americas LLC represents an infringement of valid

copyrights. Violators will be prosecuted.

Trademarks

All trademarks referenced in this manual are the property of their

respective owners.

Manufacturer

Wacker Neuson Production Americas LLC

N92W15000 Anthony Avenue

Menomonee Falls, WI 53051 U.S.A.

Tel: (262) 255-0500 · Fax: (262) 255-0550 · Tel: (800) 770-0957

www.wackerneuson.com

Original instructions

This Operator’s Manual presents the original instructions. The original

language of this Operator’s Manual is American English.

PG 2A Foreword

wc_tx001378gb.fm 3

Foreword

SAVE THESE INSTRUCTIONS—This manual contains important instructions for

the machine models below. These instructions have been written expressly by

Wacker Neuson Production Americas LLC and must be followed during installation,

operation, and maintenance of the machines.

Machine

documentation

 From this point forward in this documentation, Wacker Neuson Production

Americas L

LC will be referred to as Wacker Neuson.

 Keep a copy of the Operator’s Manual with the machine at all times.

 Use the separate Parts Book supplied with the machine to order replacement

pa

rts.

 Refer to the separate Repair Manual for detailed instructions on servicing and

repairing the machine.

 If you are missing any of these documents, please contact Wacker Neuson to

o

rder a replacement or visit www.wacke

rneuson.com.

 When ordering parts or requesting service information, be prepared to provide

th

e machine model number, item number, revision number, and serial number.

Expectations

for

information in

this manual

 This manual provides information and procedures to safely operate and

maintain the above Wacker Neuson model(s). For your own safety and to

re

duce the risk of injury, carefully read, understand, and observe all inst

ructions

d

escribed in this manua

l.

 Wacker Neuson expressly reserves the right to make technical modifications,

even without notice, which improve the performance or safety standards of its

mach

ines.

 The information contained in this manual is based on machines manufactured

u

p until the time of publication. Wacker Neuson reserves the right to chang

e

a

ny portion of this information without notice.

CALIFORNIA

Proposition

65 Warning

Engine exhaust, some of its constituents, and certain vehicle components, contain

or emit chemicals known to the State of California to cause cancer and birth

defects or other reproductive harm.

Laws

pertaining to

spark

arresters

NOTICE: State Health Safety Codes and Public Resources Codes specify that in

certain locations spark arresters be used on internal combustion engines that use

hydrocarbon fuels. A spark arrester is a device designed to prevent accidental dis-

charge of sparks or flames from the engine exhaust. Spark arresters are qualified

and rated by the United States Forest Service for this purpose. In order to comply

with local laws regarding spark arresters, consult the engine distributor or the local

Health and Safety Administrator.

Manufacturer’s

approval

This manual contains references to approved parts, attachments, and modifica-

tions. The following definitions apply:

Machine Item Number

PG 2A 0007658, 0009054

Foreword PG 2A

4 wc_tx001378gb.fm

 Approved parts or attachments are those either manufactured or provided by

W

acker Neuso

n.

 Approved modifications are those performed by an authorized Wacker

Neuson service center according to written instructions published by Wacker

Neu

son.

 Unapproved parts, attachments, and modifications are those that do not

meet

the approved criteria.

Unapproved parts, attachments, or modifications may have the following conse-

quences:

 Serious injury hazards to the operator and persons in the work area

 Permanent damage to the machine which will not be covered under warranty

Contact your Wacker Neuson dealer immediately if you have questions abo

ut

approved or

unapproved parts, attachments, or modifications.

2018_CE_PG2_PG2A_en.fm

EC Declaration of Conformity

Manufacturer

Wacker Neuson Production Americas LLC, N92W15000 Anthony Avenue,

Menomonee Falls, Wisconsin USA

Product

Product category

Product function

Item number

Measured sound power level

Guaranteed sound power level

PG2A

Water Pump Units

To pump fluid

5000009054

100 dB(A)

103 dB(A)

Conformity Assessment Procedure

According to ANNEX V

Notified Body

N/A

Directives and Standards

We hereby declare that this product meets and complies with the relevant regulations and

requirements of the following directives and standards:

2000/14/EC, 2006/42/EC, 2014/30/EU

Authorized Person for Technical Documents

Robert Raethsel, Wacker Neuson Produktion GmbH & Co. KG, Wackerstrasse 6,

85084 Reichertshofen, Germany

Menomonee Falls, WI, USA,

Travis Pound

Manager, Product Engineering

For Wacker Neuson

Keith Herr

Vice President and Managing Director

For Wacker Neuson

Original Declaration of Conformity

Jeff Volden

Director, Product Engineering

For Wacker Neuson

PG 2A Table of Contents

wc_bo5000184844_12TOC.fm 7

Foreword 3

EC Declaration of Conformity 5

1 Safety Information 9

1.1 Signal Words Used in this Manual ....................................................... 9

1.2 Machine Description and Intended Use ............................................. 10

1.3 Safety Guidelines for Operating the Machine ..................................... 12

1.4 Operator Safety while Using Internal Combustion Engines ............... 14

1.5 Service Safety .................................................................................... 16

2 Labels 18

2.1 Label Locations .................................................................................. 18

2.2 Label Meanings .................................................................................. 19

3 Lifting and Transporting 21

4 Operation 22

4.1 Preparing the Machine for First Use ................................................... 22

4.2 Recommended Fuel ........................................................................... 23

4.3 Before Starting ................................................................................... 24

4.4 Starting ............................................................................................... 25

4.5 Stopping ............................................................................................. 25

4.6 Operation ............................................................................................ 26

4.7 Hoses and Clamps ............................................................................. 26

4.8 Emergency Shutdown Procedure ....................................................... 27

5 Maintenance 28

5.1 Maintaining the Emission Control System .......................................... 28

5.2 Periodic Maintenance Schedule ......................................................... 28

5.3 Cleaning the Pump ............................................................................. 29

5.4 Adjusting the Impeller Clearance ....................................................... 30

5.5 Replacing the Mechanical Seal .......................................................... 31

5.6 Spark Plug .......................................................................................... 32

5.7 Servicing the Air Cleaner .................................................................... 33

5.8 Engine Oil ........................................................................................... 34

5.9 Cleaning the Sediment Cup ............................................................... 35

5.10 Carburetor Adjustment ....................................................................... 36

Table of Contents PG 2A

8 wc_bo5000184844_12TOC.fm

5.11 Adjusting the Idle Speed .....................................................................36

5.12 Long-Term Storage .............................................................................37

6 Troubleshooting 38

7 Technical Data 39

7.1 Engine .................................................................................................39

7.2 Machine ...............................................................................................40

7.3 Sound Measurements .........................................................................40

7.4 Dimensions ..........................................................................................41

8 Emission Control Systems Information and Warranty 43

8.1 Emission Control Systems Warranty Statement .................................43

9 AEM Safety Manual 45

PG 2A Safety Information

wc_si000415gb.fm 9

1 Safety Information

1.1 Signal Words Used in this Manual

This manual contains DANGER, WARNING, CAUTION, NOTICE, and

NOTE signal words which must be followed to reduce the possibility

of personal injury, damage to the equipment, or improper service.

NOTICE: Used without the safety alert symbol, NOTICE indicates a

situation which, if not avoided, could result in property damage.

Note: A Note contains additional information important to a procedure.

This is the safety alert symbol. It is used to alert you to potential personal hazards.

f Obey all safety messages that follow this symbol.

DANGER

DANGER indicates a hazardous situation which, if not avoided, will result in death

or serious injury.

f To avoid death or serious injury from this type of hazard, obey all safety

messages that follow this signal word.

WARNING

WARNING indicates a hazardous situation which, if not avoided, could result in

death or serious injury.

f To avoid possible death or serious injury from this type of hazard, obey all safety

messages that follow this signal word.

CAUTION

CAUTION indicates a hazardous situation which, if not avoided, could result in

minor or moderate injury.

f To avoid possible minor or moderate injury from this type of hazard, obey all

safety messages that follow this signal word.

Safety Information PG 2A

10 wc_si000415gb.fm

1.2 Machine Description and Intended Use

This machine is a centrifugal dewatering pump. The Wacker Neuson

Dewatering Pump consists of a tubular steel frame surrounding a

gasoline engine, a fuel tank, and an impeller pump with ports for water

suction and discharge. The engine rotates the impeller during

operation. Waste water is drawn into the pump through the suction

port and expelled through the discharge port. The operator connects

hoses to the pump and routes them so that water and solids are

drained from the work area and discharged into an appropriate

location.

This machine is intended to be used for general de-watering

applications. This machine is intended for the pumping of clear water,

or water containing solids up to the size stated within the product

specifications, and up to the flow, head and suction lift limits also

stated within the product specifications.

This machine has been designed and built strictly for the intended use

described above. Using the machine for any other purpose could

permanently damage the machine or seriously injure the operator or

other persons in the area. Machine damage caused by misuse is not

covered under warranty.

The following are some examples of misuse:

• Pumping flammable, explosive, or corrosive fluids

• Pumping hot or volatile fluids that result in pump cavitation

• Operating the pump outside of product specifications due to

incorrect diameter hoses, incorrect length hoses, other inlet or

outlet restrictions, or excessive suction lift or head

• Using the machine as a ladder, support, or work surface

• Using the machine to carry or transport passengers or equipment

• Operating the machine outside of factory specifications

• Operating the machine in a manner inconsistent with all warnings

found on the machine and in the Operator’s Manual.

This machine has been designed and built in accordance with the

latest global safety standards. It has been carefully engineered to

eliminate hazards as far as practicable and to increase operator

safety through protective guards and labeling. However, some risks

may remain even after protective measures have been taken. They

are called residual risks. On this machine, they may include exposure

to:

• Heat, noise, exhaust, and carbon monoxide from the engine

• Fire hazards from improper refueling techniques

PG 2A Safety Information

wc_si000415gb.fm 11

• Fuel and its fumes

• Personal injury from improper lifting techniques

• Projectile hazard from discharge

• Crushing hazards from a tipping or falling pump

To protect yourself and others, make sure you thoroughly read and

understand the safety information presented in this manual before

operating the machine.

Safety Information PG 2A

12 wc_si000415gb.fm

1.3 Safety Guidelines for Operating the Machine

Familiarity and proper training are required for the safe operation of the

machine. Machines operated improperly or by untrained personnel

can be hazardous. Read the operating instructions contained in this

manual and the engine manual, and familiarize yourself with the

location and proper use of all controls. Inexperienced operators should

receive instruction from someone familiar with the machine before

being allowed to operate it.

Operator qualifications

Only trained personnel are permitted to start, operate, and shut down

the machine. They also must meet the following qualifications:

• have received instruction on how to properly use the machine

• are familiar with required safety devices

The machine must not be accessed or operated by:

• children

• people impaired by alcohol or drugs

Personal Protective Equipment (PPE)

Wear the following Personal Protective Equipment (PPE) while

operating this machine:

• Close-fitting work clothes that do not hinder movement

• Safety glasses with side shields

• Hearing protection

• Safety-toed footwear

1.3.1 Do not touch the engine or muffler while the engine is on or

immediately after it has been turned off. These areas get hot and may

cause burns.

1.3.2 Do not use accessories or attachments that are not recommended by

Wacker Neuson. Damage to equipment and injury to the user may

result.

1.3.3 Do not pump volatile, flammable, or low flash point fluids. These fluids

could ignite or explode.

1.3.4 Do not pump corrosive chemicals or water containing toxic

substances. These fluids could create serious health and

environmental hazards. Contact local authorities for assistance.

1.3.5 Do not open the priming plug when the pump is hot. Do not loosen or

remove inlet or discharge hose fittings when the pump is hot. Hot water

inside could be pressurized much like the radiator on an automobile.

Allow the pump to cool to the touch before loosening the plug and

before loosening or removing the inlet or discharge hose fittings.

WARNING

PG 2A Safety Information

wc_si000415gb.fm 13

1.3.6 Do not open pump housing cover while pump is operating, or start

pump with the cover off. The rotating impeller inside the pump can cut

or sever objects caught in it.

1.3.7 Do not block or restrict flow from inlet line or discharge line. Remove

kinks from discharge line before starting pump. Operation with a

blocked inlet line or discharge line can cause water inside pump to

overheat.

1.3.8 Read, understand, and follow procedures in the Operator’s Manual

before attempting to operate the machine.

1.3.9 Be sure operator is familiar with proper safety precautions and

operation techniques before using machine.

1.3.10 Be sure the machine is on a firm, level surface and will not tip, roll,

slide, or fall while operating.

1.3.11 Close fuel valve on engines equipped with one when machine is not

being operated.

1.3.12 Store the machine properly when it is not being used. The machine

should be stored in a clean, dry location out of the reach of children.

Safety Information PG 2A

14 wc_si000415gb.fm

1.4 Operator Safety while Using Internal Combustion Engines

Operating safety

When operating the pump:

• Keep the area around exhaust pipe free of flammable materials.

• Check the fuel lines and the fuel tank for leaks and cracks before

starting the engine.

When operating the pump:

• Do not smoke while operating the machine.

• Do not run the machine if fuel leaks are present or the fuel lines

are loose.

• Do not run the engine near sparks or open flames.

• Do not touch the engine or muffler while the engine is running or

immediately after it has been turned off.

• Do not operate a machine when its fuel cap is loose or missing.

• Do not start the engine if fuel has spilled or a fuel odor is present.

Move the machine away from the spill and wipe the machine dry

before starting.

Refueling safety

When refueling the engine:

• Clean up any spilled fuel immediately.

• Refill the fuel tank in a well-ventilated area.

• Replace the fuel tank cap after refueling.

WARNING

Internal combustion engines present special hazards during operation and fueling.

Failure to follow the warnings and safety standards could result in severe injury or

death.

f Read and follow the warning instructions in the engine owner’s manual and the

safety guidelines below.

DANGER

Asphyxiation hazard. Using a pump indoors CAN KILL YOU IN MINUTES. Pump

exhaust contains carbon monoxide. This is a poison you cannot see or smell.

f NEVER use this pump inside a home or garage, EVEN IF doors and windows

are open. Only use OUTSIDE and far away from windows, doors, and vents.

f NEVER use a pump inside an enclosed area, such as a tunnel or a trench,

unless adequate ventilation is provided through such items as exhaust fans or

hoses.

PG 2A Safety Information

wc_si000415gb.fm 15

When refueling the engine:

• Do not smoke.

• Do not refuel a hot or running engine.

• Do not refuel the engine near sparks or open flames.

• Do not refuel if the machine is positioned in a truck fitted with a

plastic bed liner. Static electricity can ignite the fuel or fuel

vapors.

Safety Information PG 2A

16 wc_si000415gb.fm

1.5 Service Safety

A poorly maintained machine can become a safety hazard! In order

for the machine to operate safely and properly over a long period of

time, periodic maintenance and occasional repairs are necessary.

Personal Protective Equipment (PPE)

Wear the following Personal Protective Equipment (PPE) while

servicing or maintaining this machine:

• Close-fitting work clothes that do not hinder movement

• Safety glasses with side shields

• Hearing protection

• Safety-toed footwear

In addition, before servicing or maintaining the machine:

• Tie back long hair.

• Remove all jewelry (including rings).

1.5.1 Do not attempt to clean or service the machine while it is running.

Rotating parts can cause severe injury.

1.5.2 Do not crank a flooded engine with the spark plug removed on

gasoline-powered engines. Fuel trapped in the cylinder will squirt out

the spark plug opening.

1.5.3 Do not test for spark on gasoline-powered engines if the engine is

flooded or the smell of gasoline is present. A stray spark could ignite

the fumes.

1.5.4 Do not use gasoline or other types of fuels or flammable solvents to

clean parts, especially in enclosed areas. Fumes from fuels and

solvents can become explosive.

1.5.5 Keep the area around the muffler free of debris such as leaves, paper,

cartons, etc. A hot muffler could ignite the debris and start a fire.

1.5.6 Replace worn or damaged components with spare parts designed and

approved by Wacker Neuson.

1.5.7 When replacement parts are required for this machine, use only

Wacker Neuson replacement parts or those parts equivalent to the

original in all types of specifications, such as physical dimensions,

type, strength, and material.

1.5.8 Disconnect the spark plug on machines equipped with gasoline

engines, before servicing, to avoid accidental start-up.

WARNING

PG 2A Safety Information

wc_si000415gb.fm 17

Notes

Labels PG 2A

18 wc_si000416gb.fm

2 Labels

2.1 Label Locations

wc_gr000833

A

C

D

E

G, H

F

B

PG 2A Labels

wc_si000416gb.fm 19

1.2 Label Meanings

A

DANGER

Asphyxiation hazard.

 Engines emit carbon monoxide.

 Do not run the machine indoors or in an enclosed

area.

 NEVER use inside a home or garage, EVEN IF doors

and windows are open.

Only use OUTSIDE and far away from windows, doors,

and vents.

 Read the Operator’s Manual.

 No sparks, flames, or burning objects near the

machine.

 Stop the engine before refueling.

B

WARNING

Hot surface

C

CAUTION

Read and understand the supplied Operator’s Manual

before operating this machine. Failure to do so

increases the risk of injury to yourself and others.

D

WARNING

Pressurized contents. Do not open when hot!

E

Impeller rotation.

STOP

178715

wc_gr014566

wc_gr014563

wc_gr014565

wc_gr014564

Labels PG 2A

20 wc_si000416gb.fm

F

Guaranteed sound power level in db(A)

G

A nameplate listing the model number, item number,

revision number, and serial number is attached to each

unit. Please record the information found on this name-

plate so it will be available should the nameplate

become lost or damaged. When ordering parts or

requesting service information, you will always be asked

to specify the model number, item number, revision

number, and serial number of the unit.

La page charge ...

Wacker Neuson PG2A Manuel utilisateur

Wacker Neuson PG2A Manuel utilisateur

dans d''autres langues

Documents connexes