Wacker Neuson PG3A Manuel utilisateur

Operator’s Manual

Notice d'emploi

Pump

Pompe

PG3A

Type PG3A

Document 5000184898

Date

1117

Version

11

Language EN-FR

5000184898

Copyright notice

All rights, including copying and distribution rights, are reserved.

This publication may be photocopied by the original purchaser of the

machine. Any other type of reproduction is prohibited without express

written permission from Wacker Neuson Production Americas LLC.

Any type of reproduction or distribution not authorized by Wacker

Neuson Production Americas LLC represents an infringement of valid

copyrights. Violators will be prosecuted.

Trademarks

All trademarks referenced in this manual are the property of their

respective owners.

Manufacturer

Wacker Neuson Production Americas LLC

N92W15000 Anthony Avenue

Menomonee Falls, WI 53051 U.S.A.

Tel: (262) 255-0500 · Fax: (262) 255-0550 · Tel: (800) 770-0957

www.wackerneuson.com

Original instructions

This Operator’s Manual presents the original instructions. The original

language of this Operator’s Manual is American English.

PG 3A Foreword

wc_tx001328gb.fm 3

Foreword

SAVE THESE INSTRUCTIONS—This manual contains important instructions for

the machine models below. These instructions have been written expressly by

Wacker Neuson Production Americas LLC and must be followed during installation,

operation, and maintenance of the machines.

Machine

documentation

 From this point forward in this documentation, Wacker Neuson Production

Americas L

LC will be referred to as Wacker Neuson.

 Keep a copy of the Operator’s Manual with the machine at all times.

 Use the separate Parts Book supplied with the machine to order replacement

parts.

 If you are missing any of these documents, please contact Wacker Neuson to

o

rder a replacement or visit www.wacke

rneuson.com.

 When ordering parts or requesting service information, be prepared to provide

th

e machine model number, item number, revision number, and serial number.

Expectations

for

information in

this manual

 This manual provides information and procedures to safely operate and main-

tain the above Wacker Neuson model(s). For your own safety and to reduce the

risk

of injury, carefully read, understand, and observe all instructions

described

in this manual.

 Wacker Neuson expressly reserves the right to make technical modifications,

even without notice, which improve the performance or safety standards of its

mach

ines.

 The information contained in this manual is based on machines manufactured

u

p until the time of publication. Wacker Neuson reserves the right to chang

e

a

ny portion of this information without notice.

 The illustrations, parts, and procedures in this manual refer to Wacker Neuson

fa

ctory-installed components. Your machine may vary depending on th

e

re

quirements of your specific region.

CALIFORNIA

Proposition

65 Warning

Combustion exhaust, some of its constituents, and certain vehicle components

contain or emit chemicals known to the State of California to cause cancer and

birth defects or other reproductive harm.

Laws

pertaining to

spark

arresters

NOTICE: State Health Safety Codes and Public Resources Codes specify that in

certain locations spark arresters be used on internal combustion engines that use

hydrocarbon fuels. A spark arrester is a device designed to prevent accidental dis-

charge of sparks or flames from the engine exhaust. Spark arresters are qualified

and rated by the United States Forest Service for this purpose. In order to comply

with local laws regarding spark arresters, consult the engine distributor or the local

Health and Safety Administrator.

Machine Item Number

PG 3A 0007659

PG 3A I 0009055

Foreword PG 3A

4 wc_tx001328gb.fm

Manufacturer’s

approval

This manual contains references to approved parts, attachments, and modifica-

tions. The following definitions apply:

 Approved parts or attachments are those either manufactured or provided by

W

acker Neuso

n.

 Approved modifications are those performed by an authorized Wacker Neu-

son service center according to written instructions published by Wacker Neu-

son.

 Unapproved parts, attachments, and modifications are those that do not

meet

the approved criteria.

Unapproved parts, attachments, or modifications may have the following conse-

quences:

 Serious injury hazards to the operator and persons in the work area

 Permanent damage to the machine which will not be covered under warranty

Contact your Wacker Neuson dealer immediately if you have questions abo

ut

approved or

unapproved parts, attachments, or modifications.

2017_CE_PG3_PG3A_en.fm

EC Declaration of Conformity

Manufacturer

Wacker Neuson Production Americas LLC, N92W15000 Anthony Avenue,

Menomonee Falls, Wisconsin USA

Product

Product category

Product function

Item number

Net installed power

Measured sound power level

Guaranteed sound power level

PG3A

Water Pump Units

To pump fluid

5000009055

3.6 kW

102 dB(A)

105 dB(A)

Conformity Assessment Procedure

According to ANNEX V

Notified Body

Lloyds Register Verification Limited (Notified Body No 0038)

71 Fenchurch Street, London EC3M 4BS, United Kingdom

Directives and Standards

We hereby declare that this product meets and complies with the relevant regulations and

requirements of the following directives and standards:

2000/14/EC, 2006/42/EC, 2014/30/EU

Authorized Person for Technical Documents

Robert Raethsel, Wacker Neuson Produktion GmbH & Co. KG, Wackerstrasse 6,

85084 Reichertshofen, Germany

Menomonee Falls, WI, USA, 28.08.17

Travis Pound

Manager, Product Engineering

For Wacker Neuson

Original Declaration of Conformity

Keith Herr

Vice President and Managing Director

For Wacker Neuson

Jeff Volden

Director, Product Engineering

For Wacker Neuson

wc_bo5000184874_11TOC.fm 7

Table of ContentsPG 2A

Foreword 3

EC Declaration of Conformity 5

1 Safety Information 9

1.1 Signal Words Used in this Manual ....................................................... 9

1.2 Machine Description and Intended Use ............................................. 10

1.3 Safety Guidelines for Operating the Machine ..................................... 11

1.4 Operator Safety while Using Internal Combustion Engines ............... 13

1.5 Service Safety .................................................................................... 14

2 Labels 15

2.1 Label Locations .................................................................................. 15

2.2 Label Meanings .................................................................................. 16

3 Lifting and Transporting 18

4 Maintenance 19

4.1 Maintaining the Emission Control System .......................................... 19

4.2 Periodic Maintenance Schedule ......................................................... 19

4.3 Cleaning the Pump ............................................................................. 20

4.4 Adjusting the Impeller Clearance ....................................................... 21

4.5 Replacing the Mechanical Seal .......................................................... 22

4.6 Spark Plug .......................................................................................... 23

4.7 Servicing the Air Cleaner .................................................................... 24

4.8 Engine Oil ........................................................................................... 25

4.9 Cleaning the Sediment Cup (Honda) ................................................. 26

4.10 Adjusting the Carburetor .................................................................... 27

4.11 Adjusting the Idle Speed .................................................................... 27

4.12 Long-Term Storage ............................................................................ 28

5 Operation 29

5.1 Preparing the Machine for First Use ................................................... 29

5.2 Recommended Fuel ........................................................................... 29

5.3 Before Starting ................................................................................... 30

5.4 Starting ............................................................................................... 31

5.5 Stopping ............................................................................................. 31

5.6 Operation ............................................................................................ 32

8 wc_bo5000184874_11TOC.fm

Table of Contents PG 2A

5.7 Hoses and Clamps ..............................................................................32

5.8 Emergency Shutdown Procedure ........................................................33

6 Troubleshooting 34

7 Technical Data 35

7.1 Engine .................................................................................................35

7.2 Machine ...............................................................................................36

7.3 Sound Measurements .........................................................................36

7.4 Dimensions ..........................................................................................37

8 Emission Control Systems

Information and Warranty—Gasoline 38

8.1 Emission Control Systems Warranty Statement .................................38

9 AEM Safety Manual 40

wc_si000069gb.fm

9

PG 2A / 3A Safety Information

1 Safety Information

1.1 Signal Words Used in this Manual

This manual contains DANGER, WARNING, CAUTION, NOTICE, and NOTE

signal words which must be followed to reduce the possibility of personal injury,

damage to the equipment, or improper service.

NOTICE: Used without the safety alert symbol, NOTICE indicates a situation

which, if not avoided, could result in property damage.

Note: A Note contains additional information important to a procedure.

This is the safety alert symbol. It is used to alert you to potential personal hazards.

f Obey all safety messages that follow this symbol.

DANGER

DANGER indicates a hazardous situation which, if not avoided, will result in death

or serious injury.

f To avoid death or serious injury from this type of hazard, obey all safety

messages that follow this signal word.

WARNING

WARNING indicates a hazardous situation which, if not avoided, could result in

death or serious injury.

f To avoid possible death or serious injury from this type of hazard, obey all safety

messages that follow this signal word.

CAUTION

CAUTION indicates a hazardous situation which, if not avoided, could result in

minor or moderate injury.

f To avoid possible minor or moderate injury from this type of hazard, obey all

safety messages that follow this signal word.

wc_si000069gb.fm

10

Safety Information PG 2A / 3A

1.2 Machine Description and Intended Use

This machine is a centrifugal dewatering pump. The Wacker Neuson Dewatering

Pump consists of a tubular steel frame surrounding a gasoline engine, a fuel tank,

and an impeller pump with ports for water suction and discharge. The engine

rotates the impeller during operation. Waste water is drawn into the pump through

the suction port and expelled through the discharge port. The operator connects

hoses to the pump and routes them so that water and solids are drained from the

work area and discharged into an appropriate location.

This machine is intended to be used for general de-watering applications. This

machine is intended for the pumping of clear water, or water containing solids up to

the size stated within the product specifications, and up to the flow, head and

suction lift limits also stated within the product specifications.

This machine has been designed and built strictly for the intended use described

above. Using the machine for any other purpose could permanently damage the

machine or seriously injure the operator or other persons in the area. Machine

damage caused by misuse is not covered under warranty.

The following are some examples of misuse:

 Pumping flammable, explosive, or corrosive fluids

 Pumping hot or volatile fluids that result in pump cavitation

 Operating the pump outside of product specifications due to incorrect diameter

hose

s, incorrect length hoses, other inlet or outlet

restrictions, or excessive

suction

lift or head

 Using the machine as a ladder, support, or work surface

 Using the machine to carry or transport passengers or equipment

 Operating the machine outside of factory specifications

 Operating the machine in a manner inconsistent with all warnings found on the

machine and in the Operator’s Manual.

This machine has been designed and built in accordance with the latest global

safety standards. It has been carefully engineered to eliminate hazards as far as

practicable and to increase operator safety through protective guards and labeling.

However, some risks may remain even after protective measures have been taken.

They are called residual risks. On this machine, they may include exposure to:

 Heat, noise, exhaust, and carbon monoxide from the engine

 Fire hazards from improper refueling techniques

 Fuel and its fumes

 Personal injury from improper lifting techniques

 Projectile hazard from discharge

 Crushing hazards from a tipping or falling pump

To protect yourself and others, make sure you thoroughly read and understand the

safety information presented in this manual before operating the machine.

wc_si000069gb.fm

11

PG 2A / 3A Safety Information

1.3 Safety Guidelines for Operating the Machine

Familiarity and proper training are required for the safe operation of the machine.

Machines operated improperly or by untrained personnel can be hazardous. Read

the operating instructions contained in this manual and the engine manual, and

familiarize yourself with the location and proper use of all controls. Inexperienced

operators should receive instruction from someone familiar with the machine

before being allowed to operate it.

Operator

qualifications

Only trained personnel are permitted to start, operate, and shut down the machine.

They also must meet the following qualifications:

 have received instruction on how to properly use the machine

 are familiar with required safety devices

The machine must not be accessed or operated by:

 children

 people impaired by alcohol or drugs

Personal

Protective

Equipment

(PPE)

Wear the following Personal Protective Equipment (PPE) while operating this

machine:

 Close-fitting work clothes that do not hinder movement

 Safety glasses with side shields

 Hearing protection

 Safety-toed footwear

 Do not allow anyone to operate this equipment without proper training. People

operating this equipment must be familiar with the risks and hazards associated

with it.

 Do not touch the engine or muffler while the engine is on or immediately after it

has been turned off. These areas get hot and may cause burns.

 Do not use accessories or attachments that are not recommended by Wacker

Neuson. Damage to equipment and injury to the user may result.

 Do not pump volatile, flammable, or low flash point fluids. These fluids could

ignite or explode.

 Do not pump corrosive chemicals or water containing toxic substances. These

fluids could create serious health and environmental hazards. Contact local

authorities for assistance.

 Do not open the priming plug when the pump is hot. Do not loosen or remove

inlet or discharge hose fittings when the pump is hot. Hot water inside could be

pressurized much like the radiator on an automobile. Allow the pump to cool to

the touch before loosening the plug and before loosening or removing the inlet

or discharge hose fittings.

 Do not open pump housing cover while pump is operating, or start pump with

the cover off. The rotating impeller inside the pump can cut or sever objects

caught in it.

 Do not block or restrict flow from inlet line or discharge line. Remove kinks from

discharge line before starting pump. Operation with a blocked inlet line or

discharge line can cause water inside pump to overheat.

 Read, understand, and follow procedures in the Operator’s Manual before

attempting to operate the machine.

WARNING

wc_si000069gb.fm

12

Safety Information PG 2A / 3A

 Be sure operator is familiar with proper safety precautions and operation

techniques before using machine.

 Be sure the machine is on a firm, level surface and will not tip, roll, slide, or fall

while operating.

 Close fuel valve on engines equipped with one when machine is not being

operated.

 Store the machine properly when it is not being used. The machine should be

stored in a clean, dry location out of the reach of children.

wc_si000069gb.fm

13

PG 2A / 3A Safety Information

1.4 Operator Safety while Using Internal Combustion Engines

Operating

safety

When operating the pump:

 Keep the area around exhaust pipe free of flammable materials.

 Check the fuel lines and the fuel tank for leaks and cracks before starting the

engine.

When operating the pump:

 Do not smoke while operating the machine.

 Do not run the machine if fuel leaks are present or the fuel lines are loose.

 Do not run the engine near sparks or open flames.

 Do not touch the engine or muffler while the engine is running or immediately

after it has been turned off.

 Do not operate a machine when its fuel cap is loose or missing.

 Do not start the engine if fuel has spilled or a fuel odor is present. Move the

machine away from the spill and wipe the machine dry before starting.

Refueling

safety

When refueling the engine:

 Clean up any spilled fuel immediately.

 Refill the fuel tank in a well-ventilated area.

 Replace the fuel tank cap after refueling.

When refueling the engine:

 Do not smoke.

 Do not refuel a hot or running engine.

 Do not refuel the engine near sparks or open flames.

 Do not refuel if the machine is positioned in a truck fitted with a plastic bed liner.

Static electricity can ignite the fuel or fuel vapors.

WARNING

Internal combustion engines present special hazards during operation and fueling.

Failure to follow the warnings and safety standards could result in severe injury or

death.

f Read and follow the warning instructions in the engine owner’s manual and the

safety guidelines below.

DANGER

Asphyxiation hazard. Using a pump indoors CAN KILL YOU IN MINUTES. Pump

exhaust contains carbon monoxide. This is a poison you cannot see or smell.

f NEVER use this pump inside a home or garage, EVEN IF doors and windows

are open. Only use OUTSIDE and far away from windows, doors, and vents.

f NEVER use a pump inside an enclosed area, such as a tunnel or a trench,

unless adequate ventilation is provided through such items as exhaust fans or

hoses.

wc_si000069gb.fm

14

Safety Information PG 2A / 3A

1.5 Service Safety

A poorly maintained machine can become a safety hazard! In order for the

machine to operate safely and properly over a long period of time, periodic

maintenance and occasional repairs are necessary.

Personal

Protective

Equipment

(PPE)

Wear the following Personal Protective Equipment (PPE) while servicing or

maintaining this machine:

 Close-fitting work clothes that do not hinder movement

 Safety glasses with side shields

 Hearing protection

 Safety-toed footwear

In addition, before servicing or maintaining the machine:

 Tie back long hair.

 Remove all jewelry (including rings).

 Do not attempt to clean or service the machine while it is running. Rotating parts

can cause severe injury.

 Do not crank a flooded engine with the spark plug removed on gasoline-

powered engines. Fuel trapped in the cylinder will squirt out the spark plug

opening.

 Do not test for spark on gasoline-powered engines if the engine is flooded or the

smell of gasoline is present. A stray spark could ignite the fumes.

 Do not use gasoline or other types of fuels or flammable solvents to clean parts,

especially in enclosed areas. Fumes from fuels and solvents can become

explosive.

 Keep the area around the muffler free of debris such as leaves, paper, cartons,

etc. A hot muffler could ignite the debris and start a fire.

 Replace worn or damaged components with spare parts designed and

approved by Wacker Neuson.

 When replacement parts are required for this machine, use only Wacker

Neuson replacement parts or those parts equivalent to the original in all types of

specifications, such as physical dimensions, type, strength, and material.

 Disconnect the spark plug on machines equipped with gasoline engines, before

servicing, to avoid accidental start-up.

WARNING

PG 3A Labels

wc_si000519gb.fm 15

2 Labels

2.1 Label Locations

wc_gr000833

A

C

D

E

G, H

F

B

Labels PG 3A

16 wc_si000519gb.fm

2.2 Label Meanings

A

Only use OUTSIDE and far away from windows, doors,

and vents.

B

WARNING

Hot surface

C

CAUTION

Read and understand the supplied Operator’s Manual

before operating this machine. Failure to do so

increases the risk of injury to yourself and others.

D

WARNING

Pressurized contents. Do not open when hot!

E

Impeller rotation.

STOPSTOP

178715178715

wc_gr014566

wc_gr014563

wc_gr014565

wc_gr014564

PG 3A Labels

wc_si000519gb.fm 17

F

Guaranteed sound power level in db(A)

G

A nameplate listing the model number, item number,

revision number, and serial number is attached to each

unit. Please record the information found on this name-

plate so it will be available should the nameplate

become lost or damaged. When ordering parts or

requesting service information, you will always be asked

to specify the model number, item number, revision

number, and serial number of the unit.

wc_tx001379gb.fm

18

Lifting and Transporting PG 2A / 3A

3 Lifting and Transporting

Lifting the

machine

This pump is heavy enough to cause injury if proper lifting techniques are not used.

Observe the following guidelines when lifting the pump.

 Do not attempt to lift the pump unassisted. Use appropriate lifting equipment

such as slings, chains, hooks, ramps, or jacks.

 Make sure lifting equipment is attached securely and has enough weight-

bearing capacity to lift or hold the pump safely.

 Remain aware of the location of other people nearby when lifting the pump.

Transporting

the machine

Observe the following guidelines when transporting the pump to and from the job

site.

 Drain the fuel tank before transporting the pump.

 Ensure that the pump is securely strapped down in the transport vehicle to

prevent it from sliding or tipping.

 Do not refuel the pump in or on the transport vehicle. Move the pump to its

operating location and then fill the fuel tank.

wc_tx000178gb.fm

19

PG 2A / 3A Maintenance

4 Maintenance

4.1 Maintaining the Emission Control System

Normal maintenance, replacement or repair of emission control devices and

systems may be performed by any repair establishment or individual; however,

warranty repairs must be performed by a dealer/service center authorized by the

engine manufacturer. See the supplied engine owner’s manual for the applicable

emission warranty information.

4.2 Periodic Maintenance Schedule

The table below lists basic machine maintenance. Tasks designated with check

marks may be performed by the operator. Tasks designated with square bullet

points require special training and equipment.

Daily

before

starting

After

first

20 hrs.

Every

50

hrs.

Every

100

hrs.

Every

300

hrs.

Check fuel level.

3

Check engine oil level.

3

Inspect air cleaner element.

Replace as needed.

3

Check external hardware.

3

Inspect hoses and housing for leaks.

3

Clean air cleaner element.



Change engine oil.



Clean cooling system.



Check and clean spark plug.



Clean sediment cup.



Check and adjust valve clearance.



Check and adjust impeller clearance.



wc_tx000178gb.fm

20

Maintenance PG 2A / 3A

4.3 Cleaning the Pump

After pumping water containing a large amount of dirt or debris, clean out inside of

pump housing.

1. Remove drain plug (b) from pump housing and drain any water left in pump.

2. Loosen the four knobs holding the pump cover (a) and remove cover.

3. Clean out dirt and debris. Inspect impeller and volute insert for wear.

The impeller may develop sharp edges. Use care when cleaning around impeller to

avoid getting cut.

WARNING

w c _ g r 0 0 0 8 3 7

=

>

La page charge ...

Wacker Neuson PG3A Manuel utilisateur

Wacker Neuson PG3A Manuel utilisateur

dans d''autres langues

Documents connexes