Yamaha FS1R Le manuel du propriétaire

Marque: Yamaha

Modèle: FS1R

Catégorie: Instruments de musique

Taper: Le manuel du propriétaire

OWNER’S MANUAL

PRODUCT SAFETY MARKINGS: Yamaha electronic

products may have either labels similar to the graphics shown

below or molded/stamped facsimiles of these graphics on the

enclosure. The explanation of these graphics appears on this

page. Please observe all cautions indicated on this page and

those indicated in the safety instruction section.

ENVIRONMENTAL ISSUES: Yamaha strives to produce

products that are both user safe and environmentally friendly.

We sincerely believe that our products and the production

methods used to produce them, meet these goals. In keeping

with both the letter and the spirit of the law, we want you to be

aware of the following:

Battery Notice: This product MAY contain a small non-

rechargable battery which (if applicable) is soldered in place.

The average life span of this type of battery is approximately

five years. When replacement becomes necessary, contact a

qualified service representative to perform the replacement.

Warning: Do not attempt to recharge, disassemble, or

incinerate this type of battery. Keep all batteries away from

children. Dispose of used batteries promptly and as regulated

by applicable laws. Note: In some areas, the servicer is

required by law to return the defective parts. However, you do

have the option of having the servicer dispose of these parts

for you.

Disposal Notice: Should this product become damaged

beyond repair, or for some reason its useful life is considered

to be at an end, please observe all local, state, and federal

regulations that relate to the disposal of products that contain

lead, batteries, plastics, etc.

NOTICE: Service charges incurred due to lack of knowledge

relating to how a function or effect works (when the unit is

operating as designed) are not covered by the manufacturer’s

warranty, and are therefore the owners responsibility. Please

study this manual carefully and consult your dealer before

requesting service.

NAME PLATE LOCATION: The graphic below indicates the

location of the name plate. The model number, serial number,

power requirements, etc., are located on this plate. You should

record the model number, serial number, and the date of

purchase in the spaces provided below and retain this manual

as a permanent record of your purchase.

Model

Serial No.

Purchase Date

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK.

DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The exclamation point within the equi-

lateral triangle is intended to alert the

user to the presence of important oper-

ating and maintenance (servicing)

instructions in the literature accompa-

nying the product.

The lightning flash with arrowhead

symbol, within the equilateral triangle,

is intended to alert the user to the pres-

ence of uninsulated “dangerous volt-

age” within the product’s enclosure

that may be of sufficient magnitude to

constitute a risk of electrical shock.

IMPORTANT NOTICE: All Yamaha electronic products are

tested and approved by an independent safety testing

laboratory in order that you may be sure that when it is

properly installed and used in its normal and customary

manner, all foreseeable risks have been eliminated. DO NOT

modify this unit or commission others to do so unless

specifically authorized by Yamaha. Product performance

and/or safety standards may be diminished. Claims filed under

the expressed warranty may be denied if the unit is/has been

modified. Implied warranties may also be affected.

SPECIFICATIONS SUBJECT TO CHANGE: The information

contained in this manual is believed to be correct at the time

of printing. However, Yamaha reserves the right to change or

modify any of the specifications without notice or obligation to

update existing units.

SPECIAL MESSAGE SECTION

92-469- 1

RISK OFELECTRIC SHOCK

DO NOT OPEN

CAUTION

FCC/E/qx 9/24/98 8:19 PM Page 2

92-469- 3

IMPORTANT SAFETY INSTRUCTIONS

INFORMATION RELATING TO PERSONAL INJURY, ELECTRICAL SHOCK,

AND FIRE HAZARD POSSIBILITIES HAS BEEN INCLUDED IN THIS LIST.

WARNING- When using any electrical or electronic product,

basic precautions should always be followed. These

precautions include, but are not limited to, the following:

1. Read all Safety Instructions, Installation Instructions,

Special Message Section items, and any Assembly

Instructions found in this manual BEFORE making any

connections, including connection to the main supply.

2. Do not attempt to service this product beyond that

described in the user-maintenance instructions. All other

servicing should be referred to qualified service personnel.

3. Main Power Supply Verification: Yamaha products are

manufactured specifically for the supply voltage in the area

where they are to be sold. If you should move, or if any doubt

exists about the supply voltage in your area, please contact

your dealer for supply voltage verification and (if applicable)

instructions. The required supply voltage is printed on the

name plate. For name plate location, please refer to the

graphic found in the Special Message Section of this manual.

4. DANGER-Grounding Instructions: This product must be

grounded and therefore has been equipped with a three pin

attachment plug. If this product should malfunction, the ground

pin provides a path of low resistance for electrical current,

reducing the risk of electrical shock. If your wall socket will not

accommodate this type plug, contact an electrician to have

the outlet replaced in accordance with local electrical codes.

Do NOT modify the plug or change the plug to a different type!

5. WARNING: Do not place this product or any other

objects on the power cord or place it in a position where

anyone could walk on, trip over, or roll anything over power or

connecting cords of any kind. The use of an extension cord is

not recommended! If you must use an extension cord, the

minimum wire size for a 25' cord (or less) is 18 AWG. NOTE:

The smaller the AWG number, the larger the current handling

capacity. For longer extension cords, consult a local

electrician.

6. Ventilation: Electronic products, unless specifically

designed for enclosed installations, should be placed in

locations that do not interfere with proper ventilation. If

instructions for enclosed installations are not provided, it must

be assumed that unobstructed ventilation is required.

7. Temperature considerations: Electronic products should

be installed in locations that do not seriously contribute to their

operating temperature. Placement of this product close to heat

sources such as; radiators, heat registers etc., should be

avoided.

8. This product was NOT designed for use in wet/damp

locations and should not be used near water or exposed to

rain. Examples of wet /damp locations are; near a swimming

pool, spa, tub, sink, or wet basement.

9. This product should be used only with the components

supplied or; a cart ,rack, or stand that is recommended by the

manufacturer. If a cart, rack, or stand is used, please observe

all safety markings and instructions that accompany the

accessory product.

10. The power supply cord (plug) should be disconnected

from the outlet when electronic products are to be left unused

for extended periods of time. Cords should also be

disconnected when there is a high probability of lightening

and/or electrical storm activity.

11. Care should be taken that objects do not fall and

liquids are not spilled into the enclosure through any openings

that may exist.

12. Electrical/electronic products should be serviced by a

qualified service person when:

a. The power supply cord has been damaged; or

b. Objects have fallen, been inserted, or liquids have

been spilled into the enclosure through openings; or

c. The product has been exposed to rain; or

d. The product does not operate, exhibits a marked

change in performance; or

e. The product has been dropped, or the enclosure of the

product has been damaged.

13. This product, either alone or in combination with an

amplifier and headphones or speaker/s, may be capable of

producing sound levels that could cause permanent hearing

loss. DO NOT operate for a long period of time at a high

volume level or at a level that is uncomfortable. If you

experience any hearing loss or ringing in the ears, you should

consult an audiologist.

IMPORTANT: The louder the sound, the shorter the time

period before damage occurs.

14. Some Yamaha products may have benches and/or

accessory mounting fixtures that are either supplied as a part

of the product or as optional accessories. Some of these items

are designed to be dealer assembled or installed. Please

make sure that benches are stable and any optional fixtures

(where applicable) are well secured BEFORE using. Benches

supplied by Yamaha are designed for seating only. No other

uses are recommended.

PLEASE KEEP THIS MANUAL

FCC/E/qx 9/24/98 8:19 PM Page 3

1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!

This product, when installed as indicated in the instructions

contained in this manual, meets FCC requirements. Modifications

not expressly approved by Yamaha may void your authority, granted

by the FCC, to use the product.

2. IMPORTANT: When connecting this product to accessories and/or

another product use only high quality shielded cables. Cable/s

supplied with this product MUST be used. Follow all installation

instructions. Failure to follow instructions could void your FCC

authorization to use this product in the USA.

3. NOTE: This product has been tested and found to comply with the

requirements listed in FCC Regulations, Part 15 for Class “B” digital

devices. Compliance with these requirements provides a

reasonable level of assurance that your use of this product in a

residential environment will not result in harmful interference with

other electronic devices. This equipment generates/uses radio

frequencies and, if not installed and used according to the

instructions found in the users manual, may cause interference

harmful to the operation of other electronic devices. Compliance

with FCC regulations does not guarantee that interference will not

occur in all installations. If this product is found to be the source of

interference, which can be determined by turning the unit “OFF”

and “ON”, please try to eliminate the problem by using one of the

following measures:

Relocate either this product or the device that is being affected by

the interference.

Utilize power outlets that are on different branch (circuit breaker or

fuse) circuits or install AC line filter/s.

In the case of radio or TV interference, relocate/reorient the

antenna. If the antenna lead-in is 300 ohm ribbon lead, change the

lead-in to co-axial type cable.

If these corrective measures do not produce satisfactory results,

please contact the local retailer authorized to distribute this type of

product. If you can not locate the appropriate retailer, please contact

Yamaha Corporation of America, Electronic Service Division, 6600

Orangethorpe Ave, Buena Park, CA90620

The above statements apply ONLY to those products distributed by

Yamaha Corporation of America or its subsidiaries.

ADVARSEL!

Lithiumbatteri—Eksplosionsfare ved fejlagtig håndtering. Udskiftning

må kun ske med batteri af samme fabrikat og type. Levér det brugte

batteri tilbage til leverandoren.

VARNING

Explosionsfara vid felaktigt batteribyte. Använd samma batterityp

eller en ekvivalent typ som rekommenderas av apparattillverkaren.

Kassera använt batteri enlight fabrikantens instruktion.

VAROITUS

Paristo voi räjähtää, jos se on virheellisesti asennettu. Vaihda paristo

ainoastaan laitevalmistajan suosittelemaan tyyppiin. Hävitä käytetty

paristo valmistajan ohjeiden mukaisesti.

NEDERLAND / THE NETHERLANDS

• Dit apparaat bevat een lithium batterij voor geheugen back-up.

• This apparatus contains a lithium battery for memory back-up.

• Raadpleeg uw leverancier over de verwijdering van de batterij op

het moment dat u het apparaat ann het einde van de levensduur

afdankt of de volgende Yamaha Service Afdeiing:

Yamaha Music Nederland Service Afdeiing

Kanaalweg 18-G, 3526 KL UTRECHT

Tel. 030-2828425

• For the removal of the battery at the moment of the disposal at the

end of the service life please consult your retailer or Yamaha

Service Center as follows:

Yamaha Music Nederland Service Center

Address : Kanaalweg 18-G, 3526 KL UTRECHT

Tel : 030-2828425

• Gooi de batterij niet weg, maar lever hem in als KCA.

• Do not throw away the battery. Instead, hand it in as small chemical

waste.

IMPORTANT NOTICE FOR THE UNITED KINGDOM

Connecting the Plug and Cord

WARNING: THIS APPARATUS MUST BE EARTHED

IMPORTANT. The wires in this mains lead are coloured in

accordance with the following code:

GREEN-AND-YELLOW: EARTH

BLUE : NEUTRAL

BROWN : LIVE

As the colours of the wires in the mains lead of this apparatus

may not correspond with the coloured markings identifying the

terminals in your plug proceed as follows:

The wire which is coloured GREEN-and-YELLOW must be

connected to the terminal in the plug which is marked by the

letter E or by the safety earth symbol or colored GREEN or

GREEN-and-YELLOW.

The wire which is coloured BLUE must be connected to the

terminal which is marked with the letter N or coloured BLACK.

The wire which is coloured BROWN must be connected to the

terminal which is marked with the letter L or coloured RED.

* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA.

FCC INFORMATION (U.S.A.)

• This applies only to products distributed by Yamaha-Kemble Music (U.K.) Ltd.

FCC/E/qx 11/12/98 5:52 PM Page 4

PRECAUTIONS

PLEASE READ CAREFULLY BEFORE PROCEEDING

* Please keep these precautions in a safe place for future reference.

WARNING

Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical shock,

short-circuiting, damages, fire or other hazards. These precautions include, but are not limited to, the following:

• Do not open the instrument or attempt to disassemble the internal parts or

modify them in any way. The instrument contains no user-serviceable parts. If

it should appear to be malfunctioning, discontinue use immediately and have

it inspected by qualified Yamaha service personnel.

• Do not expose the instrument to rain, use it near water or in damp or wet

conditions, or place containers on it containing liquids which might spill into

any openings.

• If the power cord or plug becomes frayed or damaged, or if there is a sudden

loss of sound during use of the instrument, or if any unusual smells or smoke

should appear to be caused by it, immediately turn off the power switch,

disconnect the electric plug from the outlet, and have the instrument

inspected by qualified Yamaha service personnel.

• Only use the voltage specified as correct for the instrument. The required

voltage is printed on the name plate of the instrument.

• Always connect the three-pin attachment plug to a properly grounded power

source. (For more information about the main power supply, see page 17.)

• Before cleaning the instrument, always remove the electric plug from the

outlet. Never insert or remove an electric plug with wet hands.

• Check the electric plug periodically and remove any dirt or dust which may

have accumulated on it.

CAUTION

Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage to the

instrument or other property. These precautions include, but are not limited to, the following:

• Do not place the power cord near heat sources such as heaters or radiators,

and do not excessively bend or otherwise damage the cord, place heavy

objects on it, or place it in a position where anyone could walk on, trip over,

or roll anything over it.

• When removing the electric plug from the instrument or an outlet, always hold

the plug itself and not the cord. Pulling by the cord can damage it.

• Do not connect the instrument to an electrical outlet using a multiple-

connector. Doing so can result in lower sound quality, or possibly cause

overheating in the outlet.

• Remove the electric plug from the outlet when the instrument is not to be

used for extended periods of time, or during electrical storms.

• Before connecting the instrument to other electronic components, turn off the

power for all components. Before turning the power on or off for all

components, set all volume levels to minimum.

• Do not expose the instrument to excessive dust or vibrations, or extreme cold

or heat (such as in direct sunlight, near a heater, or in a car during the day) to

prevent the possibility of panel disfiguration or damage to the internal

components.

• Do not use the instrument near other electrical products such as televisions,

radios, or speakers, since this might cause interference which can affect

proper operation of the other products.

• Do not place the instrument in an unstable position where it might

accidentally fall over.

• Before moving the instrument, remove all connected cables.

• When cleaning the instrument, use a soft, dry cloth. Do not use paint

thinners, solvents, cleaning fluids, or chemical-impregnated wiping cloths.

Also, do not place vinyl, plastic or rubber objects on the instrument, since

this might discolor the panel or keyboard.

• Do not rest your weight on, or place heavy objects on the instrument, and do

not use excessive force on the buttons, switches or connectors.

• Use only the stand/rack specified for the instrument. When attaching the

stand or rack, use the provided screws only. Failure to do so could cause

damage to the internal components or result in the instrument falling over.

• Do not operate the instrument for a long period of time at a high or

uncomfortable volume level, since this can cause permanent hearing loss. If

you experience any hearing loss or ringing in the ears, consult a physician.

■ REPLACING THE BACKUP BATTERY

• This instrument contains a non rechargeable internal backup battery which

permits internal data to remain stored even when the power is off. When the

backup battery needs replacing, the message "Battery Low" will display in the

LCD. When this happens, immediately back up your data (using an external

device such as the floppy disk-based Yamaha MIDI Data Filer MDF3), then have

qualified Yamaha service personnel replace the backup battery.

• Do not attempt to replace the backup battery yourself, in order to prevent the

possible serious hazards. Always have qualified Yamaha service personnel

replace the backup battery.

• Never place the backup battery in a location that a child can reach, since a

child might accidentally swallow the battery. If this should happen, consult a

physician immediately.

■ SAVING USER DATA

• Save all data to an external device such as the Yamaha MIDI Data Filer MDF3,

in order to help prevent the loss of important data due to a malfunction or

user operating error.

Yamaha cannot be held responsible for damage caused by improper use or

modifications to the instrument, or data that is lost or destroyed.

Always turn the power off when the instrument is not in use.

(1)-3

cPRECAUTIONS/E/qx 9/24/98 8:20 PM Page 5

Congratulations!

Your FS1R Format Shaping/FM Synthesis Tone Generator gives you the power of two extraordinary tone generation

systems in one compact, easy-to-use rack-mount unit. Formant Shaping synthesis gives musicians unprecedented

capability to produce and control sounds with characteristics and flexibility similar to that of the human voice. It can

also produce instrument voices that have the response and rich pitch-dependent timbral variations. FS technology

also lends itself ideally to FM synthesis, similar to the type introduced in the legendary Yamaha DX-series

synthesizers and TX-series tone generators. In addition to unprecedented voicing versatility and expressive scope,

the FS1R features an advanced control interface that facilitates both real-time performance control and editing.

Please read this owner’s manual carefully, and follow the instructions within in order to ensure proper operation. Also

keep this manual in a safe place for later reference.

1/FS1R/OM/E.qx 10/19/98 6:28 PM Page 6

Contents

FS (Formant Shaping) and

FM (Frequency Modulation) Synthesis........................8

FS Synthesis ......................................................................................8

*Formant Control...........................................................................9

*Formant Sequences:“FSeqs” ....................................................10

*Other Formant Applications ......................................................11

FM Synthesis....................................................................................11

*FM In Brief .................................................................................12

Putting It All Together.......................................................................13

The Controls & Connectors ........................................14

Front Panel.......................................................................................14

Rear Panel .......................................................................................16

Setting Up .....................................................................17

Power Supply...................................................................................17

MIDI Connections ............................................................................17

*Keyboard...................................................................................17

*Sequencer or Computer............................................................18

*G50 Guitar MIDI Converter .......................................................18

*WX-series Wind MIDI Controller................................................18

Audio Connections ..........................................................................19

*Headphones..............................................................................19

*Instrument Amplifier or Stereo Sound System ..........................19

*Mixing Console..........................................................................19

Power-on Procedure ........................................................................20

Play the Demo..................................................................................20

The PLAY Mode............................................................21

Performance & Voice Organization .................................................21

*Performance Combinations.......................................................21

*Voices ........................................................................................21

*Bank Selection via MIDI ............................................................22

The Play Mode (Performance).........................................................22

Perf Ch (Performance Channel) .................................................23

(Bank) .........................................................................................23

(Program Number)......................................................................23

Pfm Vol (Performance Volume)...................................................23

Pfm Pan (Performance Pan) .......................................................23

RevRtn (Reverb Return)..............................................................23

VarRtn (Variation Return) ............................................................24

PfmNSft (Performance Note Shift) ..............................................24

The PART ASSIGN Mode.................................................................24

Rcv Ch (Receive Channel) .........................................................25

Rcv Max (Maximum Receive Channel: parts 1 & 2 only)...........25

(Bank) .........................................................................................25

(Program Number)......................................................................25

Volume ........................................................................................25

Pan..............................................................................................25

RevSend (Reverb Send).............................................................26

VarSend (Variation Send)............................................................26

InsEfSw (Insertion Effect Switch)................................................26

DryLvl (Dry Level).......................................................................26

Filter (Filter Frequency Offset) ....................................................26

NoteSft (Note Shift) .....................................................................26

The [MUTE/SOLO] Button in the Part Assign Mode...................26

The Search Function.............................................................................27

EDITING.........................................................................28

General Editing Procedure ..............................................................28

The [MUTE/SOLO] Button in the Edit Modes .............................29

EDIT [PERFORMANCE] ...................................................................30

COMMON ...................................................................................30

*CtrlSrc (Control Source) .......................................................30

*CtrlDst (Control Destination) ................................................31

*Fseq (Format Sequence) .....................................................32

*Others...................................................................................35

PART ...........................................................................................37

*Tone......................................................................................37

*EG (Envelope Generator).....................................................39

*Pitch......................................................................................40

*Others...................................................................................41

STORE PERFORMANCE.............................................................44

RECALL PERFORMANCE...........................................................44

EDIT [EFFECT].................................................................................45

Effect Signal Flow .......................................................................45

Rev..............................................................................................45

Type .......................................................................................46

Type-Specific Reverb Parameters.........................................46

Reverb Pan ............................................................................46

Rev Return .............................................................................46

Var...............................................................................................46

Type .......................................................................................46

Type-Specific Variation Parameters.......................................46

Var Pan ..................................................................................47

Var Return ..............................................................................47

SendVar→Rev ........................................................................47

Ins ...............................................................................................47

Type .......................................................................................47

Type-Specific Insertion Parameters.......................................47

Ins Pan...................................................................................47

SendIns→Rev.........................................................................48

SendIns→Var..........................................................................48

InsDryLevel............................................................................48

EQ ...............................................................................................48

Low Freq................................................................................48

Low Gain................................................................................48

Low Q ....................................................................................48

Low Shape.............................................................................48

Mid Freq.................................................................................49

Mid Gain ................................................................................49

Mid Q .....................................................................................49

High Freq...............................................................................49

High Gain...............................................................................49

High Q ...................................................................................49

High Shape............................................................................49

EDIT [VOICE] ...................................................................................50

COMMON ...................................................................................50

*LFO1 (Low Frequency Oscillator 1).....................................51

*LFO2 (Low Frequency Oscillator 2).....................................52

*Filter......................................................................................53

*PitchEG (Pitch Envelope Generator)....................................57

*Others...................................................................................58

OPERATOR .................................................................................61

*Osc (Oscillator) ....................................................................62

*EG (Amplitude Envelope Generator) ...................................66

*FrqEG (Frequency EG).........................................................67

*Sns (Sensitivity) ....................................................................68

STORE VOICE.............................................................................70

RECALL VOICE...........................................................................70

UTILITY Functions .......................................................71

SYSTEM ...........................................................................................71

*Master........................................................................................71

*MIDI ...........................................................................................72

*Control .......................................................................................74

*Others........................................................................................76

DUMPOUT .......................................................................................77

*DUMPOUT Operation................................................................77

INITIAL .............................................................................................78

DEMO...............................................................................................78

Troubleshooting ...........................................................79

Alert Display .................................................................82

Specifications...............................................................83

Index..............................................................................84

1/FS1R/OM/E.qx 10/19/98 6:28 PM Page 7

FS (Formant Shaping) and FM

(Frequency Modulation) Synthesis

FS (Formant Shaping) and

FM (Frequency Modulation) Synthesis

Although based on Yamaha’s newly developed FS (Formant Shaping) synthesis technology, The FS1R actually

integrates two tone generation concepts for extraordinarily broad voicing versatility. Formant Shaping synthesis

gives musicians unprecedented capability to produce and control sounds with characteristics and flexibility similar

to that of the human voice. It can also produce instrument voices that have the response and rich pitch-dependent

timbral variations — in short, the “musicality” — of natural acoustic instruments. The bonus is that the base FS

technology has been realized using an architecture which also lends itself ideally to FM synthesis, similar to the type

introduced in the legendary Yamaha DX-series synthesizers and TX-series tone generators. Thus the FS1R can

create anything from totally new simulations of human vocal sounds to classic DX electric piano voices, and

anything in between.

FS Synthesis

The term “formant” refers to the distinct spectral patterns which define the recognizable sounds of human speech,

such as the vowels “a” or “i.” In human speech, the vocal cords themselves are only capable of creating the basic

driving sound and defining pitch (similar to the oscillator in a music synthesis system). The formants which define

the sounds of speech are created by the shape of the vocal cavity (i.e. the trachea and mouth). In traditional speech

synthesis systems this is simulated by using an oscillator to perform the function of the vocal cords, and a series of

controllable bandpass filters to create the required format shapes. Consonant sounds such as “k” or “t,” and

fricatives such as “f,” are based on slightly different principles, requiring a noise generator rather than an oscillator,

and depending more on amplitude envelope shape than formant shape for recognizability. Formants play an

important role in defining the sound of many acoustic musical instruments as well as the human voice.

Rather than a cumbersome system of oscillators and filters to synthesize the effect of formants, the FS synthesis

system consists of 16 formant “operators” — 8 “voiced” operators, and 8 “unvoiced” operators (3 to 5 formants are

generally considered to be more than enough to synthesize speech). Each operator digitally simulates the effect of

both the driving source (oscillator) and filter in one easily manageable unit. The voiced operators produced pitched

sounds which can be played on a musical scale via a MIDI keyboard or other MIDI controller. The unvoiced

operators can be used to produce noise components of speech-like sound, or they can be used in much the same

way as noise generators in more orthodox synthesis systems (e.g. to produce percussive sounds or sound effects).

The term “operators” is borrowed from Yamaha FM synthesis, because the FS1R’s voiced operators can be

combined in a variety of “algorithms” to create sound in exactly the same way as in the original FM synthesizers

such as the DX7.

1 2 3 4 5

Operators

Voiced

Unvoiced

Formants

6 7 8

1/FS1R/OM/E.qx 10/19/98 6:28 PM Page 8

■ Formant Control

Each formant operator has a range of parameters which determine its shape and therefore contribute to the overall

sound: center frequency, level, width, and skirt (the shape of the “flare” at the bottom of the formant’s bell-shaped

response curve).

As an example, suppose we have a formant configuration that produces an “a” type sound. This can be changed to

an “i” sound by shifting the center frequencies and levels of the formants. If this is done in real time at an

appropriate speed, we produce the sound “ai”.

This type of formant control can be accomplished in the FS1R in several ways. First, independent frequency and

level envelope generators are provided for each operator, so time-based timbral shifts like the one described above

can be achieved entirely by using the envelope generators. Second, any of the available controllers can be

assigned to the formant parameters — the control knobs, a modulation wheel, foot controller, etc. — to allow realtime

manual control while playing. Either of these methods of formant control are all you’ll need to create musical sounds

for most applications, but the last and most complex type of formant control on the FS1R is made possible by

“FSeqs” (Formant Sequences), described in the following section.

=“a”

=“i”

Level

Width

Skirt

Center Frequency

1/FS1R/OM/E.qx 10/19/98 6:28 PM Page 9

EG, LFO1, Velocity, and Manual Formant Control Parameters

The following parameter groups and parameters are essential for EG-based formant control. Refer to the

parameter descriptions for details:

• EDIT [VOICE] mode OPERATOR/Osc/.....................................................Page 62

• EDIT [VOICE] mode OPERATOR/EG/ ......................................................Page 66

• EDIT [VOICE] mode OPERATOR/FrqEG/ .................................................Page 67

• EDIT [VOICE] mode OPERATOR/Sns/ .....................................................Page 68

The following parameter groups and parameters are essential for manual and MIDI formant control. Refer to the

parameter descriptions for details:

• EDIT [PERFORMANCE] mode COMMON/CtrlSrc....................................Page 30

• EDIT [PERFORMANCE] mode COMMON/CtrlDst....................................Page 31

• EDIT [PERFORMANCE] mode PART/Tone/Formant.................................Page 37

• EDIT [PERFORMANCE] mode PART/Tone/FM.........................................Page 37

• EDIT [VOICE] mode OPERATOR/Osc/.....................................................Page 62

• EDIT [VOICE] mode OPERATOR/Sns/Freq Bias......................................Page 69

• EDIT [VOICE] mode OPERATOR/Sns/Width Bias ....................................Page 69

• EDIT [VOICE] mode COMMON/Others/Formant .....................................Page 59

• EDIT [VOICE] mode COMMON/Others/FM..............................................Page 59

The following parameter groups and parameters are essential for LFO1 formant control. Refer to the parameter

descriptions for details:

• EDIT [VOICE] mode COMMON/LFO1/FreqModDepth ............................Page 52

• EDIT [VOICE] mode OPERATOR/Sns/Freq Mod......................................Page 70

The following parameter groups and parameters are essential for velocity formant control. Refer to the

parameter descriptions for details:

• EDIT [VOICE] mode OPERATOR/Sns/FreqVelocity..................................Page 68

■ Formant Sequences: “FSeqs”

In addition to envelope generator, LFO1, velocity, and manual control, the FS1R features a range of 90 preset FSeqs

(Formant Sequences) which can be used to “sequence” the formants to produce voice-like phrases, rhythm loops,

and more. FSeqs are sequences of formant frequency, fundamental pitch, and level data which have been created

by analyzing the formant content of actual sounds. FSeq playback speed can be set at a fixed value, controlled via

a MIDI clock signal, varied by note velocity (e.g. keyboard dynamics) or varied manually when the “scratch” Fseq

mode is selected. And since the sound of formants is not pitch dependent, FSeq playback speed and pitch can be

varied over an extremely wide range without altering the basic timbre of the sound (something that even the best

samplers cannot do).

Fseqs actually have 8 “tracks”, each of which contains the frequency and level data for one operator pair (voiced

and unvoiced). Normally, the Fseq tracks are assigned to the corresponding operator pair, but these assignments

can be changed for special effects.

1/FS1R/OM/E.qx 10/19/98 6:28 PM Page 10

FSeq Formant Control Parameters

The following parameter groups and parameters are essential for FSeq formant control. Refer to the parameter

descriptions for details:

• EDIT [PERFORMANCE] mode COMMON/Fseq/ .....................................Page 32

• EDIT [VOICE] mode OPERATOR/Osc/.....................................................Page 62

■ Other Formant Applications

By modifying our approach slightly and thinking of each FS1R formant operator as a combination of oscillator, filter,

and amplifier (similar to the standard VCA → VCF → VCA structure of traditional analog synthesizers), it is possible

to come up with some innovative uses for these flexible sonic building blocks. For example, although each formant

is basically a bandpass filter, if we broaden the bandwidth enough and lower the center frequency we end up with

what looks more like a low pass filter. If we add another narrow-bandwidth formant to our low-pass filter we end up

with a resonant low-pass filter.

The unvoiced operators also offer some unique possibilities. Although they basically produce noise, if the bandwidth

of the formant is made narrow enough we remove all harmonics and end up with a pure sine wave. Thus, in some

applications the unvoiced operators can actually be used as extra oscillators.

FM Synthesis

The fact that Formant Shaping synthesis uses a system of operators to produce sound is what makes it compatible

with FM (Frequency Modulation) synthesis. By rearranging the operators into a variety of “algorithms” with

carrier/modulator relationships between certain operators, the FS system is fully capable of producing the same type

of FM sounds as the Yamaha DX-series synthesizers and TX-series tone generators.

The FS1R actually takes FM synthesis to new levels of musical versatility and control. Unlike Yamaha’s original FM

synthesizers and tone generators the FS1R provides a range of 88 algorithms to choose from, and a choice of 8

different waveforms for each oscillator, thus significantly expanding the range of sound which can be produced.

And, of course, the ability to combine Formant Shaping with FM opens a whole new universe of musical possibilities.

Not only is the FS1R capable of reproducing the great sounds of the DX and TX-series instruments, it actually comes

with a complete set of 1,152 original DX voices pre-programmed in preset memory If you have other DX voices you

have programmed yourself or obtained from other sources, they can be loaded into the FS1R too, and used with

virtually no change in sound (See the separate “Data List” booklet for details on parameter compatibility).

nThe FS1R can receive bulk voice data from Yamaha DX-series synthesizers and TX-series tone generators. The received data (single voice)

will be loaded into the part 1 voice edit buffer of the currently selected performance setup.

Synthesized Low-pass Filter Synthesized Resontant Low-pass Filter

1/FS1R/OM/E.qx 10/19/98 6:28 PM Page 11

■ FM In Brief

Briefly, FM synthesis is based on arranging operators — individual oscillators which can function as both modulators

and carriers — in “algorithms” capable of producing the desired sound. the most simple algorithm (algorithm 1 in

the FS1R) simply add the output of all 8 operators together, with no modulator-carrier relationships. This algorithm is

ideal for synthesizing simple “additive” sounds — like some organ voices, for example.

Much more complex harmonic spectra can be produced by using algorithms in which one or more operators

function as modulators, modulation the output of their respective carrier operators. In algorithm 6, for example,

operator 1 modulates operator 2, operator 3 modulates operator 4, and operators 5 through 8 are unmodulated.

Algorithm 2, on the other hand, includes a modulator “stack” in which operator 1 modulates operator 2, which in turn

modulates operator 3, which in turn modulates operator 4.

Note that in all three algorithms introduced above, operator 1 includes a feedback loop which allows a specified

portion of the operator’s output to be fed back to its own input for even greater timbral complexity. Since each

operator has its own amplitude EG, a virtually unlimited spectrum of responsive, musical voices can be produced.

FM Synthesis Parameters

The following parameter groups and parameters are essential for basic FM synthesis. Refer to the parameter

descriptions for details:

• EDIT [VOICE] mode COMMON/Others/...................................................Page 58

• EDIT [VOICE] mode OPERATOR/Osc/.....................................................Page 62

• EDIT [VOICE] mode OPERATOR/EG/ ......................................................Page 66

• EDIT [VOICE] mode OPERATOR/Sns/ .....................................................Page 68

1/FS1R/OM/E.qx 10/19/98 6:28 PM Page 12

Putting It All Together

Please note that the parameter groups referred to in the preceding sections are only those that apply directly to the

FS or FM functions mentioned. Keep in mind that there is an extensive range of others — envelope generators,

filters, low-frequency operators, and more — which apply to both FS and FM voices. There’s also a comprehensive

effect system including reverb, delay, modulation, and many, many more effects that can be used to refine and

polish your sound.

Indeed, the FS1R is a complex tone generator, and a thorough understanding can only be achieved through

experimentation. If you want to go beyond the presets provided (although they should be more than enough for

many applications), we urge you to go ahead and play with the parameters. Try editing the presets to create

variations. And when you’re ready for some serious programming try initializing a few internal voices (voice

initialization on page 78) and starting from scratch. Keep the manual handy and refer to the parameter descriptions

in the “EDITING” section (starting on page 28) to guide you.

The following diagrams show an overall view of how the tone generator PERFORMANCE and VOICE parameters are

related, and how the performance parts connect to the FS1R effect system.

PERFORMANCE

VARIATION

REVERB

INSERTION

UNVOICED OPERATOR

FILTER

VOICED OPERATOR

OUTPUT

IND.OUTPUT

LFO1

LFO2

PITCH EG

FSEQ

VOICE

FS1R Tone Generator Structure

FSEQ PART

FILTER SW

INS EF SW

REV/VAR SEND

CONTROLLER

1/FS1R/OM/E.qx 10/19/98 6:28 PM Page 13

The Controls & Connectors

The following brief descriptions of the FS1R controls and connectors should help you to understand the overall logic

of the interface.

Front Panel

1 2 3 4

^ $% # @

5 6 7 8 9 ) !

1 PHONES Jack

Accepts a standard pair of stereo headphones (1/4” stereo phone

plug) for headphone monitoring of the FS1R sound without the need

for external amplification equipment. The volume of the headphone

sound is adjusted via the [VOLUME] control.

2 Volume Control

Adjusts the volume of the PHONES and rear-panel R and L/MONO

outputs (the VOLUME control does not affect the INDIVIDUAL OUTPUT

jacks). Rotate clockwise to increase output volume.

3 Display

This large backlit liquid crystal display panel shows all parameters and

prompts necessary for easy, efficient operation and programming of

the FS1R. In addition, a row of icons across the bottom line of the

display simultaneously shows the status of a number of important

parameters (page 22).

The display contrast can be adjusted as described on page 76 for

optimum visibility.

4 [UTIL] Button

Selects the FS1R UTILITY mode. The UTILITY mode includes a range

of important utility functions that affect operation of the FS1R: SYSTEM,

DUMP OUT, INITIAL, and DEMO.

Details on page 71.

5 [PLAY] Button

Press this button to select the FS1R PLAY mode in which performance

setups and individual voices can be selected and played. While the

PLAY mode is active, pressing the [PLAY] button activates the

Rehearsal function which plays the currently selected voice for quick,

convenient sound-checks.

Details on page 22.

6 EDIT Buttons: [PERFORMANCE], [EFFECT], and

[VOICE]

These buttons activate the corresponding FS1R EDIT mode.

The EDIT [PERFORMANCE] button provides access to all parameters

and functions you’ll need to edit and create new performance setups.

The EDIT [EFFECT] button takes you a range of effect and EQ

parameters that you can use to add the finishing touches to your

sound.

The EDIT [VOICE] button allows detailed editing of individual voices.

Details on pages 30, 45, 50.

7 [MUTE/SOLO] Button

In any mode other than Voice Edit the [MUTE/SOLO] button can be

used to mute or solo monitor the currently selected performance part.

In the Voice Edit mode, it can be used to mute or solo monitor the

selected operator.

8 PART [ ] and [ ] Buttons

When the PLAY mode is selected (page 22) these buttons select the

part (voice) to be played or edited. Either button can be pressed

briefly for single stepping in the specified direction, or held for

continuous scrolling. Pressing both buttons simultaneously switches to

the Performance Select (ALL parts) play mode.

When the EDIT mode is selected the PART buttons can be used to

switch between parameters without having to return to the EDIT mode

menu.

1/FS1R/OM/E.qx 10/19/98 6:28 PM Page 14

9 Knob Mode Buttons

These two buttons determine the function of the FS1R’s four controller

knobs. When the upper button is lit, the knobs directly affect the FS1R

sound by controlling the parameters listed above the knobs: ATTACK,

RELEASE, FORMANT, and FM. When the lower button is lit the knobs

control the parameters assigned to KN1 through KN4 in the

UTILITY/SYSTEM/Control mode (page 74). When both buttons are

disengaged and the PART ASSIGN mode is selected, the knobs can

be used to edit the currently selected parameter for all 4 performance

parts (page 24). When both Knob Mode Buttons are disengaged, the

knobs can be used to quickly select parts or operators and edit the

corresponding values (page 28).

) Controller Knobs

These four multi-function controller knobs make realtime sound control

and editing on the FS1R easier than ever. In the PLAY mode they allow

direct realtime control of the sound as well as parameter editing, and

in the EDIT mode they can be used to directly change parameters and

values for fast, efficient operation. The knobs can be assigned to the

various parameters for exceptionally versatile control.

Press the [ENTER] button while operating the knobs for faster value

selection.

! [POWER] Control

Press to turn power ON or OFF.

@ CURSOR [ ] and [ ] Buttons

These buttons are used to select sub-modes or parameters. In some

cases the selection will be made from a menu display, and in others

the CURSOR buttons will actually switch display pages.

# VALUE [ ] and [ ] Buttons

Used to select performance setups and voices, and to edit parameter

values. Either button can be pressed briefly for single stepping in the

specified direction, or held for continuous scrolling. They also have a

large-step function which allows you to skip ahead or backward in

larger increments when selecting voices or editing numeric

parameters: press either the [ ] or [ ] button while holding the

other button.

$ [EXIT] Button

This button is used to exit from sub-modes and cancel certain

operations. No matter where you are in the FS1R display structure,

pressing the [EXIT] button (a number of times if necessary) will

eventually return you to the PLAY mode.

% [ENTER] Button

The [ENTER] button is used to engage sub-modes, confirm input, and

execute certain operations. Double-clicking this button (i.e. press the

button twice in rapid succession) provides access to the MIDI View

mode (below).

^ [SEARCH] Button

The FS1R includes a vast range of presets, which can at time make it

difficult to locate a specific performance setup or voice. The SEARCH

mode makes it easier to locate to a desired performance setup or

voice by specifying the appropriate bank and categories.

Details on page 27.

MIDI View

This function displays the MIDI control change or system exclusive data string required to control the currently

selected parameter from an external MIDI device. The MIDI data is displayed in hexadecimal format.

To engage the MIDI View function first select the desired parameter in any mode other than the SEARCH

mode, then "double click" the [ENTER] button (i.e. press the [ENTER] button twice in rapid succession). The

MIDI View display will appear.

While the MIDI View function is engaged the VALUE [ ] and [ ] buttons can be used to change values, and

the CURSOR [ ] and [ ] buttons can be used to select different parameters.

Press the [EXIT] button to return to the previous display.

1/FS1R/OM/E.qx 10/19/98 6:28 PM Page 15

Rear Panel

*& ( º

& Power Cord Connector

Plug the female end of the supplied AC power cord in here before

plugging it into an AC wall outlet.

Details on page 17.

* MIDI IN, OUT and THRU Connectors

The MIDI IN connector receives the data from an external keyboard,

sequencer or other MIDI device which is to control or transmit data to

the FS1R. The MIDI THRU connector simply re-transmits the data

received at the MIDI IN connector, allowing convenient chaining of

MIDI devices. The MIDI OUT connector transmits data corresponding

to FS1R controller knob operation, or bulk data when one of the MIDI

data transmission functions are activated.

Details on page 17.

( INDIVIDUAL OUTPUT L and R Jacks

In addition to the OUTPUT L/MONO and R jacks, described above,

individual performance parts can be assigned to the INDIVIDUAL

OUTPUT L and R jacks so that they can be sent to separate channels

of a mixer for independent processing, etc.

Details on page 19.

º OUTPUT L/MONO and R Jacks

These are the main stereo outputs from the FS1R. Be sure to connect

both outputs to the appropriate channels of a stereo sound system in

order to appreciate the full quality of the FS1R sound and effects. The

L/MONO jack can be used alone when connecting to a mono sound

system (e.g. a musical instrument amplifier).

Details on page 19.

1/FS1R/OM/E.qx 10/19/98 6:28 PM Page 16

Setting Up

Power Supply

Before making any other connections the “female” end of the AC power cord supplied with the FS1R should be

firmly plugged into the rear-panel AC cord socket. Ideally the power cord should then be plugged into a convenient

AC outlet after you’ve made all other necessary connections and placed the FS1R in the position in which it will be

used. Always make sure that the POWER switch is in the OFF (extended) position before plugging the power cord

into an AC outlet.

WARNING!

• Make sure your FS1R is rated for the AC voltage supplied in the area in which it is to be used (as listed on

the rear panel). Connecting the unit to the wrong AC supply can cause serious damage to the internal

circuitry and may even pose a shock hazard!

• Use only the AC power cord supplied with the FS1R. If the supplied cord is lost or damaged and needs to

be replaced, contact your Yamaha dealer. The use of an inappropriate replacement can pose a fire and

shock hazard!

• The type of AC power cord provided with the FS1R may be different depending on the country in which it is

purchased (a third prong may be provided for grounding purposes). Improper connection of the grounding

conductor can create the risk of electrical shock. Do NOT modify the plug provided with the FS1R. If the

plug will not fit the outlet, have a proper outlet installed by a qualified electrician. Do not use a plug adapter

which defeats the grounding conductor.

MIDI Connections

The FS1R can be used with virtually any type of MIDI controller: keyboard, wind controller, sequencer, etc. To ensure

reliable error-free transfer of MIDI data always use high-quality MIDI cables obtained from your Yamaha dealer or

music equipment store. Also avoid MIDI cables that are longer than about 15 meters, since cables longer than this

can pick up noise which can cause data errors.

The FS1R MIDI receive channel number parameters are available via the PERFORMANCE PLAY and PART ASSIGN

mode displays (pages 22 and 24, respectively). Make sure these parameters are set to match the corresponding

settings of the MIDI controller used with the FS1R. See the MIDI Implementation Chart in the separate “Data List”

booklet, and the MIDI Data Format section beginning in the separate “Data List” booklet for details for the types of MIDI

data received and transmitted by the FS1R.

nThe [MIDI] icon in the FS1R display will appear whenever MIDI data is received by the FS1R.

nWhen using the FS1R with other MIDI equipment, it is a good idea to refer to the MIDI specifications (implementation chart, MIDI data

format) of the equipment used to ensure compatibility.

■ Keyboard

This is the simplest type of setup you might use with the FS1R. Simply connect the MIDI OUT connector of the

keyboard to the MIDI IN connector on the FS1R with a MIDI cable. In this case you should set the PgmMode

parameter in the UTILITY/SYSTEM/MIDI group to “perform” (page 73).

MIDI

OUT

MIDI IN

MIDI Master Keyboard

Synthesizer

FS1R

MUSIC SYNTHESIZER

REALTIME CONTROL

EXTENDED SYNTHESIS

1/FS1R/OM/E.qx 10/19/98 6:28 PM Page 17

■ Sequencer or Computer

If you plan to use the FS1R with a sequencer or a computer equipped with sequencing software, the actual

connections you will need to make will depend on the type of sequencer/software you use, the type of MIDI interface

used, and the other equipment in your system. A simple system is shown below. In any case, you’ll probably want to

set the FS1R for multi-timbre playback (i.e. each part can be played via separate MIDI channel) by setting the

PgmMode parameter in the UTILITY/SYSTEM/MIDI group to “multi” (page 73).

■ G50 Guitar MIDI Converter

The Yamaha G50 is a high-performance Guitar MIDI Converter designed to work in conjunction with the Yamaha

G1D or B1D Divided Pickup Unit installed on an electric or steel-string acoustic guitar. The FS1R is an ideal tone

generator for use with a MIDI guitar system based on the G50.

Since the G50 produces MIDI output, the standard MIDI connection rules that apply to a keyboard or any other MIDI

controller also apply when connecting the G50 to the FS1R. One feature of the FS1R which makes it ideal for use

with the G50 is the ability to allow reception on a specified range of MIDI channels for each performance part.

■ WX-series Wind MIDI Controller

The FS1R is an ideal tone generator for use with a Yamaha WX-series Wind MIDI Controller such as the WX5 or

WX11. The WX5 can be directly connected to the FS1R MIDI IN connector, while the WX11 will require the optional

BT7 wind controller interface.

Special care must be taken with the following parameters and controls when using a WX-series Wind MIDI

Controller:

FS1R

WX5

MIDI Out MIDI In

FS1RG50

G1D etc.

MIDI Out

MIDI In

DIVIDED

MONO SYNTH

Computer

MIDI

Interface

EX5 etc.

FS1R

MIDI In MIDI Out

MIDI Out

MIDI Thru

MIDI In

MUSIC SYNTHESIZER

REALTIME CONTROL

EXTENDED SYNTHESIS

1/FS1R/OM/E.qx 10/19/98 6:28 PM Page 18

Pitch Bend

WX Lip Sensor and Pitch Bend data as transmitted in the form of MIDI pitch bend data. Be sure to set an

appropriate pitch bend range on your FS1R. For subtle control a pitch bend range setting of between about 2 and 4

should be ideal. For broader control try a range setting between about 5 and 7. For really sweeping pitch bends, try

a setting of 8 or more.

Pitch bend range parameter details on page 41.

Velocity

The WX Wind MIDI Controllers transmit breath attack information in the form of MIDI velocity data. Yamaha

recommends, however, that you set the FS1R velocity to a fixed value in order to facilitate breath control of volume.

However, if velocity is the only means you have of controlling volume and timbre, then it might be a good idea to

allow some velocity sensitivity particularly when playing voices such as bass, drums, and piano, which depend on

the characteristics of the attack for their sound.

Velocity sensitivity parameter details on page 68.

Breath Control

Breath strength information is transmitted by the WX Wind MIDI Controllers in the form of MIDI breath control data

which is primarily used to control volume and timbre. Make sure that the FS1R is set to receive breath control, and

initially set the breath control response so that the full breath control range can be used, then readjust for the

optimum range while actually playing the WX Wind MIDI Controller.

Breath control assignment and sensitivity parameter (Amp EG Bias) details on pages 69, 71 and 75.

Audio Connections

Headphones

For private listening and practice headphones are ideal. You don’t have to hook up and complete sound system,

and you won’t disturb the neighbors no matter how loud or late you play. Recommended Yamaha headphones for

FS1R monitoring are the HPE-170, HPE-160, or HPE-150 Stereo Headphones. Any standard pair of stereo

headphones with a 1/4” stereo phone plug and an impedance of between about 33 and 150 ohms can be used.

Instrument Amplifier or Stereo Sound System

The FS1R voices and effects are designed to sound their best in stereo, so you should always use a stereo sound

system to appreciate the full impact of the FS1R voices and expressive features. The OUTPUT L/MONO and R jacks

can be connected directly to musical instrument amplifiers designed for keyboard use, or to the line inputs of a

mixing console. It is also possible to connect the outputs directly to the inputs of a multitrack or stereo tape recorder.

When connecting to a mono sound system be sure to use only the OUTPUT L/MONO jack.

nIf you need to drive a mono amp or other device, connect only the L/MONO output jack. The left and right channel signals are

automatically combined and delivered via the L/MONO jack when a single phone plug is inserted in this jack and the R output jack is left

unconnected.

nMake sure that both the FS1R and your sound system are turned OFF when making connections.

Mixing Console

In addition to the stereo OUTPUT L/MONO and R jacks, the FS1R has two individual outputs: the INDIVIDUAL

OUTPUT L and R jacks. The stereo and individual outputs can be fed to separate channels of a mixing console for

individual processing. Individual “parts” of a performance setup can be assigned to the individual outputs via the

PLAY mode InsEfSw parameter (page 26) and EDIT PERFORMANCE Mode COMMON/Others/IndOut parameter

(page 35).

1/FS1R/OM/E.qx 10/19/98 6:28 PM Page 19

Power-on Procedure

Always follow proper procedure when powering-up a sound system to minimize the possibility of damage to the

equipment (and your ears!).

Make sure your sound system’s main level/volume control(s) and the FS1R volume control are turned all

the way down prior to turning power on.

Turn on the FS1R.

Turn on your MIDI controller (and computer/sequencer, if used).

Turn on the sound system.

Raise the sound system volume to a reasonable level.

Gradually raise the FS1R VOLUME control while playing the MIDI controller to set the desired listening

level.

nSome keyboards and other MIDI controllers automatically transmit MIDI control change data corresponding to their control status when the

power switch is turned ON or OFF. The FS1R is programmed to receive this data and respond accordingly, so it is preferable to turn the

FS1R ON before turning the controlling device ON.

Play the Demo

Once you’ve set up your FS1R system, you might like to play the pre-programmed demo sequence to hear how

some of the voices sound. This process will also help to familiarize you with some of the FS1R’s selection and

editing procedures.

Select the Utility Mode

Press the [UTILITY] button to select the utility mode.

Select the Demo Mode

Use the CURSOR [ ] and [ ] buttons to select the “DEMO” item.

Press [ENTER] and Confirm

Press the [ENTER] button to engage the DEMO mode, then press [ENTER] again if it’s OK to go ahead with the

demo, or [EXIT] to abort.

Select a Song

Use the VALUE [ ] and [ ] buttons to select the demo song number you want to start with.

Run the Demo

Press the [ENTER] button to run the demo. Playback will start with the selected song, then all other songs will

be played in sequence. The cycle will repeat until stopped.

Stop the Demo

Press the [EXIT] button to stop demo playback. This will return you to the demo song select display.

Return To the Play Mode When Done

Press the [PLAY] button to return to the PLAY mode.

nAfter demo playback, data corresponding to the voices used in the demo will remain in the FS1R edit buffer. Demo voice bulk data,

program change and other events can be handled in the same way as other FS1R data.

1/FS1R/OM/E.qx 10/19/98 6:28 PM Page 20

La page est en cours de chargement...

Yamaha FS1R Le manuel du propriétaire

Marque: Yamaha

Modèle: FS1R

Catégorie: Instruments de musique

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

italiano: Yamaha FS1R Manuale del proprietario
English: Yamaha FS1R Owner's manual
español: Yamaha FS1R El manual del propietario
Deutsch: Yamaha FS1R Bedienungsanleitung
русский: Yamaha FS1R Инструкция по применению
Nederlands: Yamaha FS1R de handleiding
português: Yamaha FS1R Manual do proprietário
dansk: Yamaha FS1R Brugervejledning
polski: Yamaha FS1R Instrukcja obsługi
čeština: Yamaha FS1R Návod k obsluze
svenska: Yamaha FS1R Bruksanvisning
Türkçe: Yamaha FS1R El kitabı
suomi: Yamaha FS1R Omistajan opas
română: Yamaha FS1R Manualul proprietarului

Yamaha FS1R Le manuel du propriétaire

Yamaha FS1R Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents