Hotpoint HSS25IFPCC Le manuel du propriétaire

Marque: Hotpoint

Modèle: HSS25IFPCC

Catégorie: Frigos

Taper: Le manuel du propriétaire

Ce manuel convient également à

HSS25IFPWW

Hotpoint.com
Refrigerators
Side by Side
162D6746P011   39-60479   08-06 JR
Write your model and serial numbers here:
Model # _____________________
Serial # _____________________
Find these numbers on a label inside
the refrigerator compartment at the top
on the right side behind the controls.
Réfrigérateurs
Côte à côte
Manuel d’utilisation 
et d’installation
La section française commence à la page 23
Safety Information
Connect Electricity  . . . . . . . . . . . . .3
Extension Cords  . . . . . . . . . . . . . . .2
Proper Disposal . . . . . . . . . . . . . . . .2
Safety Precautions  . . . . . . . . . . . . . .2
Operating Instructions
Automatic Icemaker  . . . . . . . . . .7–8
Controls   . . . . . . . . . . . . . . . . . . . . .6
Crispers and Pans  . . . . . . . . . . . . . .5
How to Install Features . . . . . . . . . .4
Ice and Water Dispenser  . . . . . . . .8
Shelves and Bins  . . . . . . . . . . . . . . .4
Water Filter Cartridge . . . . . . . . . . .7
Care and Cleaning
Cleaning . . . . . . . . . . . . . . . . . . . . . .9
Light Bulbs   . . . . . . . . . . . . . . . . . . .9
Installation Instructions
Preparing to Install   . . . . . . . . . . .10
Water Line Installation  . . . . . .11–13
Troubleshooting Tips
Before You Call 
For Service  . . . . . . . . . . . . . . . .14–16
Normal Operating Sounds  . . . . . .14
Consumer Support
Consumer Support  . . . .Back Cover
Performance Data Sheet  . . . . . . .19
Product Registration 
(Canadian)  . . . . . . . . . . . . . . .21, 22
Product Registration 
(U.S.)  . . . . . . . . . . . . . . . . . . . .20, 21
State of California Water 
Treatment Device Certificate  . . . .19
Warranty (Canadian)  . . . . . . . . . .17
Warranty (U.S.) . . . . . . . . . . . . . . .18
Refrigeradores
Lado a lado
Models 20, 22, 25
Owner’s Manual and
Installation Instructions
Manual del propietario
e instalación
La sección en español empieza en la página 42
Refrigerators
Side by Side
Mesures de sécurité
Comment vous débarrasser 
convenablement de votre 
ancien réfrigérateur  . . . . . . . . . . . . . . . .23
Cordons prolongateurs . . . . . . . . . . . . . .23
Mesures de sécurité  . . . . . . . . . . . . . . . . .23
Raccordement électrique  . . . . . . . . . . . .24
Fonctionnement
Bacs à légumes  . . . . . . . . . . . . . . . . . . . . .26
Cartouche du filtre à eau  . . . . . . . . . . . .28
Clayettes et bacs  . . . . . . . . . . . . . . . . . . . .25
Installation des accessoires  . . . . . . . . . . .25
Le distributeur d’eau et de glaçons  . . . .29
Les commandes  . . . . . . . . . . . . . . . . . . . .27
Machine à glaçons automatique  . . . . .28–29
Entretien et nettoyage
Nettoyage  . . . . . . . . . . . . . . . . . . . . . . . . .30
Remplacement des ampoules  . . . . . . . .30
Installation
Installation de la 
conduite d’eau . . . . . . . . . . . . . . . . . .32–34
Préparation . . . . . . . . . . . . . . . . . . . . . . . .31
Conseils de dépannage
Avant d’appeler un réparateur  . . . . .35–38
Bruits de fonctionnement 
normaux  . . . . . . . . . . . . . . . . . . . . . . . . . .35
Service à la clientèle
Feuillet de données relatives à la 
performance de la 
cartouche HWF  . . . . . . . . . . . . . . . . . . . .40
Garantie pour la 
clientèle au Canada  . . . . . . . . . . . . . . . . .39
Service à la clientèle  . . . . . . . . . . . . . . . .41
Información de seguridad
Cables de extensión . . . . . . . . . . . . . . . . 42
Conectar la electricidad . . . . . . . . . . . . . 43
Deshacerse debidamente 
de su refrigerador . . . . . . . . . . . . . . . . . . 42
Precauciones de seguridad. . . . . . . . . . . 42
Instrucciones de operación
Cartucho del filtro de agua . . . . . . . . . . 47
Controles del refrigerador . . . . . . . . . . . 46
Dispensador . . . . . . . . . . . . . . . . . . . . . . . 48
Dispositivo automático 
para hacer hielo. . . . . . . . . . . . . . . . . 47–48
Entrepaños y recipientes  . . . . . . . . . 44–45
Gavetas de almacenamiento . . . . . . . . . 45
Instalación de las características . . . . . . 44
Cuidado y limpieza
Limpieza . . . . . . . . . . . . . . . . . . . . . . . 49–50
Reemplazo de bombillas . . . . . . . . . . . . 50
Instrucciones de instalación
Instalación de la línea 
de agua . . . . . . . . . . . . . . . . . . . . . . . . 53–56
Preparación para 
instalar el refrigerador . . . . . . . . . . . 51–52
Solucionar problemas
Antes de solicitar un servicio . . . . . . 57–60
Sonidos normales 
de la operación . . . . . . . . . . . . . . . . . . . . 57
Servicio al consumidor
Garantía para consumidores 
en los Estados Unidos . . . . . . . . . . . . . . . 61
Hoja de datos de
funcionamiento  . . . . . . . . . . . . . . . . . . . 62
Servicio al consumidor . . . . . . . . . . . . . . 63

PROPER DISPOSAL OF THE REFRIGERATOR

Child entrapment and suffocation are not problems

of the past. Junked or abandoned refrigerators are

still dangerous…even if they will sit for “just a few

days.” If you are getting rid of your old refrigerator,

please follow the instructions below to help prevent

accidents.

Before You Throw Away Your Old Refrigerator

or Freezer:

■ Take off the doors.

■ Leave the shelves in place so that children may

not easily climb inside.

Refrigerants

All refrigeration products contain refrigerants,

which under federal law must be removed prior

to product disposal. If you are getting rid of an

old refrigeration product, check with the company

handling the disposal about what to do.

USE OF EXTENSION CORDS

Because of potential safety hazards under certain conditions, we strongly recommend

against the use of an extension cord.

However, if you must use an extension cord, it is absolutely necessary that it be a UL-listed (in the United

States) or a CSA-listed (in Canada), 3-wire grounding type appliance extension cord having a grounding

type plug and outlet and that the electrical rating of the cord be 15 amperes (minimum) and 120 volts.

DANGER! RISK OF CHILD ENTRAPMENT

Consumer Support

Troubleshooting Tips Operating Instructions Safety InstructionsInstallation Instructions

IMPORTANT SAFETY INFORMATION.

READ ALL INSTRUCTIONS BEFORE USING.

WARNING!

Use this appliance only for its intended purpose as described in this Owner’s Manual.

SAFETY PRECAUTIONS

When using electrical appliances, basic safety precautions should be followed, including the following:

■

■ This refrigerator must be properly installed

and located in accordance with the Installation

Instructions before it is used.

■

■ Do not allow children to climb, stand or hang

on the shelves in the refrigerator. They could

damage the refrigerator and seriously injure

themselves.

■

■ Do not touch the cold surfaces in the freezer

compartment when hands are damp or wet. Skin

may stick to these extremely cold surfaces.

■

■ Do not store or use gasoline or other flammable

vapors and liquids in the vicinity of this or any

other appliance.

■

■ Setting the freezer control to the

O (off)

position

does not remove power to the light circuit.

■

■ Do not refreeze frozen foods which have thawed

completely.

■

■ In refrigerators with automatic icemakers,

avoid contact with the moving parts of the

ejector mechanism, or with the heating element

that releases the cubes. Do not place fingers or

hands on the automatic icemaking mechanism

while the refrigerator is plugged in.

■

■ Keep fingers out of the “pinch point” areas;

clearances between the doors and between

the doors and cabinet are necessarily small.

Be careful closing doors when children are

in the area.

■

■ Unplug the refrigerator before cleaning and

making repairs.

NOTE: We strongly recommend that any servicing be

performed by a qualified individual.

Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions Installation Instructions

www.Hotpoint.com

WARNING!

HOW TO CONNECT ELECTRICITY

Do not, under any circumstances, cut or remove the third (ground) prong from the power cord. For

personal safety, this appliance must

be properly grounded.

■

■ The power cord of this appliance is equipped with a 3-prong (grounding) plug

which mates with a standard 3-prong (grounding) wall outlet to minimize the

possibility of electric shock hazard from this appliance.

■

■ Have the wall outlet and circuit checked by a qualified electrician to make sure the

outlet is properly grounded.

■

■ If the outlet is a standard 2-prong outlet, it is your personal responsibility and

obligation to have it replaced with a properly grounded 3-prong wall outlet.

READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.

SAVE THESE INSTRUCTIONS

INSURE PROPER GROUND

EXISTS BEFORE USE

■

■ The refrigerator should always be plugged into its own

individual electrical outlet which has a voltage rating that

matches the rating plate.

■

■ This provides the best performance and also prevents

overloading house wiring circuits which could cause a

fire hazard from overheated wires.

■

■ Never unplug your refrigerator by pulling on the power

cord. Always grip plug firmly and pull straight out from

the outlet.

■

■ Repair or replace immediately all power cords that have

become frayed or otherwise damaged. Do not use a cord

that shows cracks or abrasion damage along its length or

at either end.

■

■ When moving the refrigerator away from the

wall, be careful not to roll over or damage the

power cord.

Consumer Support

Troubleshooting Tips Installation Instructions Safety InstructionsOperating Instructions

How to install features. (Not all features are on all models.)

Top Freezer Shelf

¿ TOP FREEZER SHELF

Make sure the shelf front locks into

position.

Lower Door Bin

≈ LOWER FIXED DOOR BINS

Make sure the bin fronts lock into position.

ƒ ADJUSTABLE

DOOR BINS

DOOR BIN SNUGGERS

¬ DAIRY COVER

√ BOTTLE RETAINER

Door

Shelf Front

Door

Shelf

¡ FILTER CARTRIDGE

FREEZER DOOR SHELF FRONTS

Make sure that the shelf front locks

into position.

NOTE: On dispenser models, the

longer shelf fronts go in the top

two positions.

≈

Remove Bypass Plug Install Filter Cartridge

To remove:

Lift the

front of the bin up,

then pull out.

To replace or relocate:

Engage the bin in the

molded supports of

the door, and push

in. Bin will lock in

place.

To remove:

Lift the shelf extender

straight up, then pull out.

To replace:

Engage the shelf

extender in the molded supports

of the door and push in. It will

lock in place.

About the shelves and bins. (Not all features are on all models.)

Rearranging the Shelves

To Remove

To Replace

Refrigerator Shelves:

Lift up and out

Tilt up

Insert

top hook

Lower to

lock in

place

To Remove

Freezer Shelves:

To Remove

Freezer Pan:

Remove the pan by pulling it

forward, lifting up the front

and sliding it past the

stop

location.

Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions Installation Instructions

Slide-Out Spillproof Shelf (on some models)

The slide-out spillproof shelf allows you to

reach items stored behind others. The

special edges are designed to help prevent

spills from dripping to lower shelves.

NOTE: Make sure you push the shelves all the

way back in before you close the door.

Spillproof Shelves (on some models)

Spillproof shelves have special edges

to help prevent spills from dripping to

lower shelves.

www.Hotpoint.com

About the crispers and pans.

(Not all features are on all models.)

Adjustable Humidity Crispers and Snack Pan

(on some models)

Slide the control all the way to the

High

setting to provide high humidity

recommended for most vegetables.

Slide the control all the way to the

Low

setting to provide lower humidity levels

recommended for most fruits.

LOW

HIGH

LOW

HIGH

Convertible Meat Pan (on some models)

The convertible meat pan has its own cold

air duct to allow a stream of cold air from

the freezer compartment to flow around

the pan.

The variable temperature control

regulates

the air flow from the freezer compartment.

Set control lever

to convert the pan

to normal refrigerator temperature and

provide extra vegetable storage space. Cold

air duct is turned off. Variable settings

between these extremes can be selected.

Set control lever

down

to the coldest setting

to store fresh meats. If lever is left in meat

position for a long period of time, some

frost may form on the inside of the pan.

Normal

Coldest

Crisper Removal

Crispers can easily be removed by tilting up

slightly and pulling past

stop

location.

If the door prevents you from taking out

the crispers, the refrigerator will need to

be rolled forward until the door opens

enough to slide the crispers out. In some

cases, when you roll the refrigerator out,

you will need to move the refrigerator to

the left as you roll it out.

When replacing the crispers, make

sure you slide them through the

crisper guides.

About the controls on the refrigerator.

9 IS COLDEST

0 IS OFF

9 IS COLDEST

0 IS OFF

FREEZER FRESH FOOD

Your controls will look like one of the following:

Startup Steps for Proper Temperature Control

STEP 1—Set Fresh Food Control on “5.”

STEP 2—Set Freezer Control on “5.”

STEP 3—WAIT

HOURS for temperature to stabilize.

STEP 4—If a change is needed, move the control one number at a time and allow

hours

for temperature to stabilize.

NOTE:

Setting the controls to the

(off) position does not remove power to the light circuit.

Control settings will vary based on personal preferences, usage and

operating conditions and may require more than one adjustment.

Consumer Support

Troubleshooting Tips Installation Instructions Safety InstructionsOperating Instructions

0 IS OFF

9 IS COLDEST

FREEZER

REFRIGERATOR

To Change Temperature Control Setting with Touch Pads:

• Freezer setting is on the left side of the display.

• Fresh Food setting is on the right side of the display.

— Press the warmer or colder pad for compartment and direction desired.

— Present control setting number will illuminate.

— Each time the pad is touched, compartment setting changes one number.

A display of 1 is warmest and 9 is the coldest setting.

NOTE:

Setting the controls to the

(off) position does not remove power to the light circuit.

Control settings will vary based on personal preferences, usage and

operating conditions and may require more than one adjustment.

About the water filter cartridge. (On some models.) www.Hotpoint.com

Water Filter Cartridge

The water filter cartridge is located in the back upper right

corner of the refrigerator compartment.

When to Replace the Filter on Models With a

Replacement Indicator Light

There is a replacement indicator light for the water filter

cartridge on the dispenser. This light will turn orange to tell

you that you need to replace the filter soon.

The filter cartridge should be replaced when the

replacement indicator light turns red or if the flow of water

to the dispenser or icemaker decreases.

When to Replace the Filter on Models Without a

Replacement Indicator Light

The filter cartridge should be replaced every

six months

or earlier if the flow of water to the water dispenser or

icemaker decreases.

Removing the Filter Cartridge

If you are replacing the cartridge, first remove the old one

by slowly turning it to the left.

Do not

pull down on the

cartridge. A small amount of water may drip down.

Installing the Filter Cartridge

If you are replacing a

SmartWater

cartridge

with an adapter, it must

be removed before

installing the cartridge.

To remove the adapter,

turn it to the left about

1/4 turn.

If you are replacing a

Water by Culligan

cartridge,

leave the adapter in place. This adapter will stay in the

refrigerator when you replace future cartridges.

On models without a replacement indicator light,

apply the month and year sticker to the new cartridge

to remind you to replace the filter in

six months.

Fill the replacement cartridge with water from the tap

to allow for better flow from the dispenser immediately

after installation.

Line up the arrow on the cartridge and the cartridge

holder. Place the top of the new cartridge up inside the

holder.

Do not

push it up into the holder.

Slowly turn it to the right

until the filter cartridge

stops.

DO NOT OVERTIGHTEN.

As you turn the cartridge, it

will automatically raise itself

into position. The cartridge

will move about 1/2 turn.

un water from the dispenser for 3 minutes (about 1-1/2

gallons) to clear the system and prevent sputtering.

Filter Bypass Plug

You must use the filter bypass plug when a replacement filter

cartridge is not available. The dispenser and the icemaker

will not operate without the filter or filter bypass plug.

To use the filter bypass plug on

Water by Culligan

models,

you must first remove the filter adapter from the cartridge

holder by turning it to the left.

If you have questions—visit our Website

at www.hotpoint.com,

or call 1.800.GE.CARES (1.800.432.2737).

Replacement filters:

To order additional filter cartridges in the United States,

visit our Website at www.hotpoint.com, or call GE Parts and

Accessories, 800.626.2002.

MWF

Suggested Retail $38.95–47.95

Customers in Canada should consult the yellow pages for

the nearest Mabe Service Center.

Customers outside of the United States or Canada should

contact the local distributor.

Cartridge

Holder

Filter

Bypass

Plug

Filter

Bypass

Plug

SmartWater

Water by Culligan

(appearance may vary)

With adapter

Without adapter

About the automatic icemaker.

A newly-installed refrigerator may take 12–24 hours to begin making ice.

Icemaker

Feeler Arm

Power

Switch

Green

Power Light

Automatic Icemaker (on some models)

When the refrigerator has been connected

to the water supply, set the power switch to

the

I (on)

position.

The icemaker will fill with water when

it cools to 15°F. When the bin fills to the

level of the feeler arm, the icemaker will

stop producing ice.

Be sure nothing interferes with the sweep

of the feeler arm.

Throw away the first few batches of ice to

allow the water line to clear.

The icemaker will produce seven cubes

per cycle—approximately 100–130 cubes

in a 24-hour period, depending on freezer

compartment temperature, room

temperature, number of door openings

and other use conditions.

You will hear a buzzing sound each time

the icemaker fills with water.

Consumer SupportTroubleshooting Tips

Operating InstructionsSafety Instructions

Installation Instructions

Consumer Support

Troubleshooting Tips Installation Instructions Safety InstructionsOperating Instructions

About the automatic icemaker.

It is normal for several cubes to be joined together.

If ice is not used frequently, old ice cubes will

become cloudy, taste stale, and shrink.

NOTE: In homes with lower-than-average water pressure,

you may hear the icemaker cycle multiple times when

making one batch of ice.

Icemaker Accessory Kit

If your refrigerator did not come already

equipped with an automatic icemaker, an

icemaker accessory kit is available at extra cost.

Check the back of the refrigerator for the specific

icemaker kit needed for your model.

Select or

Press the glass gently against the top of the

dispenser cradle.

The spill shelf is not self-draining. To

reduce water spotting, the shelf and its

grille should be cleaned regularly.

Locking the Dispenser (on some models)

Press the

LOCK CONTROL

pad

for 3 seconds to lock the

dispenser and control panel.

To unlock, press and hold the

pad again for 3 seconds.

If no water is dispensed when the refrigerator is

first installed, there may be air in the water line

system. Press the dispenser arm for at least two

minutes to remove trapped air from the water line

and to fill the water system. To flush out impurities

in the water line, throw away the first six glassfuls

of water.

CAUTION: Never put fingers or any other

objects into the ice crusher discharge opening.

Dispenser Light

This pad turns the

night light

in the dispenser on and off.

The light also comes on when

the dispenser cradle is pressed.

If this light burns out, it should

be replaced with a 6 watt

maximum, 12 volt DC bulb.

About the ice and water dispenser. (On some models.)

To Use the Dispenser

Important Facts About Your Dispenser

■ Do not add ice from trays or bags to the storage bin. It

may not crush or dispense well.

■ Avoid overfilling glass with ice and use of narrow glasses.

Backed-up ice can jam the chute or cause the door in the

chute to freeze shut. If ice is blocking the chute, poke it

through with a wooden spoon.

■ Beverages and foods should not be quick-chilled in the

ice storage bin. Cans, bottles or food packages in the

storage bin may cause the icemaker or auger to jam.

■ To keep dispensed ice from missing the glass, put the

glass close to, but not touching, the dispenser opening.

■ Some crushed ice may be dispensed even though you

selected

CUBED.

This happens occasionally when a few

cubes have been left in the crusher.

■ After crushed ice is dispensed, some water may drip from

the chute.

■ Sometimes a small mound of snow will form on the door

in the ice chute. This condition is normal and usually

occurs when you have dispensed crushed ice repeatedly.

The snow will eventually evaporate.

■ The first glass of water dispensed may be warmer than

the following ones. This is normal.

■ Dispensed water is not ice cold. For colder water, simply

add crushed ice or cubes before dispensing water.

Ice Storage Drawer on Dispenser Models

To remove:

Set the icemaker power switch to the

O (off)

position.

Pull the drawer straight out and then lift past the

stop

position.

To replace:

When replacing the drawer, make sure to push it

firmly into place. If it does not go all the way back,

remove it and rotate the drive mechanism 1/4 turn.

Then push the drawer back again.

Drive

Mechanism

Rotate

Spill Shelf

Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions Installation Instructions

Care and cleaning of the refrigerator. www.Hotpoint.com

Cleaning the Outside

The dispenser drip area,

(on some models)

beneath the grille, should be wiped dry. Water

left in this area may leave deposits. Remove

the deposits by adding undiluted vinegar to

the well. Soak until the deposits disappear

or become loose enough to rinse away.

The dispenser cradle

(on some models).

Before cleaning, lock the dispenser by

pressing and holding the

LOCK CONTROL

pad for 3 seconds. Clean with warm water

and baking soda solution—about a

tablespoon (15 ml) of baking soda to a

quart (1 l) of water. Rinse thoroughly

and wipe dry.

The door handles and trim.

Clean with a

cloth dampened with soapy water. Dry

with a soft cloth.

Keep the outside clean.

Wipe with a clean

cloth lightly dampened with kitchen

appliance wax or mild liquid dish detergent.

Dry and polish with a clean, soft cloth.

Do not wipe the refrigerator with a soiled dish

cloth or wet towel. These may leave a residue

that can erode the paint. Do not use scouring

pads, powdered cleaners, bleach or cleaners

containing bleach because these products can

scratch and weaken the paint finish.

Cleaning the Inside

To help prevent odors,

leave an open box of

baking soda in the refrigerator and freezer

compartments.

Unplug the refrigerator before cleaning.

If this

is not practical, wring excess moisture out

of sponge or cloth when cleaning around

switches, lights or controls.

Use warm water and baking soda solution—

about a tablespoon (15 ml) of baking soda

to a quart (1 l) of water. This both cleans

and neutralizes odors. Rinse and wipe dry.

After cleaning the door gaskets, apply a

thin layer of petroleum jelly to the door

gaskets at the hinge side. This helps keep

the gaskets from sticking and bending out

of shape.

Drain opening in freezer compartment.

During yearly cleaning, remove bottom

freezer pan and flush a solution of baking

soda—1 teaspoon (5 ml) and 2 cups (500

ml) of hot (not boiling) water— through

the drain line with the help of a meat

baster. This will help eliminate odor and

reduce the likelihood of a clogged drain

line. If drain becomes clogged, use a meat

baster and baking soda solution to force the

clog through the drain line.

Avoid cleaning cold glass shelves with hot water

because the extreme temperature difference may

cause them to break. Handle glass shelves carefully.

Bumping tempered glass can cause it to shatter.

Do not wash any plastic refrigerator parts in the

dishwasher.

For long vacations or absences, remove food and unplug

the refrigerator. Clean the interior with a baking soda

solution of one tablespoon (15 ml) of baking soda to one

quart (1 l) of water. Leave the doors open.

Set the icemaker power switch to the

O (off)

position and

shut off the water supply to the refrigerator.

Behind the Refrigerator

Be careful when moving the refrigerator away from the

wall. All types of floor coverings can be damaged,

particularly cushioned coverings and those with embossed

surfaces.

Pull the refrigerator straight out and return it to position by

pushing it straight in. Moving the refrigerator in a side

direction may result in damage to the floor covering or

refrigerator.

When pushing the refrigerator back, make sure you don’t roll over

the power cord or icemaker supply line (on some models).

Preparing for Vacation

Preparing to Move

Secure all loose items such as grille, shelves and drawers by taping them securely in place to prevent damage.

Be sure the refrigerator stays in an upright position during moving.

Turning the control to the 0 (off) position does not remove power to the light circuit.

Replacing the Light Bulbs

Unplug the refrigerator.

Remove the shelf just below the light shield.

Replace with an appliance bulb of the same

or lower wattage.

Reinstall the shelf and plug the refrigerator

back in.

BEFORE YOU BEGIN

Read these instructions completely and carefully.

•

IMPORTANT

–

Save these

instructions for local inspector’s use.

•

IMPORTANT

–

Observe all

governing codes and ordinances.

• Note to Installer

–

Be sure to leave these

instructions with the Consumer.

• Note to Consumer

–

Keep these instructions

for future reference.

• Skill level – Installation of this appliance requires

basic mechanical skills.

• Completion time – Refrigerator Installation

15 minutes

• Proper installation is the responsibility of installer.

• Product failure due to improper installation is not

covered under the Warranty.

REFRIGERATOR LOCATION

• Do not install the refrigerator where the temperature

will go below 60°F (16°C) because it will not run

often enough to maintain proper temperatures.

• Install it on a floor strong enough to support it fully

loaded.

Installation Instructions

Models 20, 22, 25

Allow the following clearances for ease of installation,

proper air circulation and plumbing and electrical

connections.

• Sides 1/8″ (4 mm) • Top 1″ (25 mm) • Back 1″ (25 mm)

A door clearance of 3/4″ (19 mm) is needed for a 90º door

opening which provides better access to food storage area.

CLEARANCES

If the refrigerator has an icemaker, it will have to be

connected to a cold water line. A GE water supply kit

is available at extra cost from your dealer, by visiting

our Website at www.Hotpoint.com (in Canada, at

www.geappliances.ca), or from Parts and Accessories,

800.626.2002.

WATER SUPPLY TO THE ICEMAKER

(on some models)

Questions? Call 800.GE.CARES (800.432.2737)

or Visit our Website at:

www.Hotpoint.com

Questions? In Canada, call 1.800.361.3400

or Visit our Website at:

www.geappliances.ca

The rollers have 3 purposes:

■ Rollers adjust so the door closes easily when opened

about halfway.

■ Rollers adjust so the refrigerator is firmly positioned

on the floor and does not wobble.

■ Rollers allow you to move the refrigerator away from

the wall for cleaning.

To adjust the rollers, remove the base grille by pulling it

out at the bottom.

Turn the roller adjusting screws clockwise to raise the

refrigerator, counterclockwise to lower it. Use an

adjustable wrench (3/8″ hex head bolt) or pliers.

To replace base grille, line up the clips on back of grille

between the bar and the bottom of the cabinet. Push

forward until grille snaps into place.

ROLLERS

After leveling, make sure that the doors are even at the top.

To make the doors even, adjust the refrigerator door as

follows:

Remove the Base Grille, open the doors, then pull the

grille straight out.

Determine which of the two doors is higher than the other.

Lift the lower door, along with the small cam.

Place the shim between the Door Metal Hinge and the

small cam as shown.

Press in the shim so that it fits in between the metal

hinge and the plastic cam.

Close the doors and check if they are level at the top.

If one door is still lower than the other, repeat the

process and insert another shim.

Shim

Shims are stored

under the fresh food

door top hinge cover.

DOOR ALIGNMENT

NOTE: If the doors are not even and the shim is already

inserted, you can remove the shim to lower the door.

Installation Instructions

INSTALLING THE WATER LINE

Recommended copper water supply kits are WX8X2,

WX8X3 or WX8X4, depending on the amount of

tubing you need. Approved plastic water supply lines are

GE SmartConnect

™

Refrigerator Tubing (WX08X10002,

WX08X10006, WX08X10015 and WX08X10025).

When connecting your refrigerator to a GE Reverse

Osmosis Water System, the only approved installation

is with a GE RVKit. For other reverse osmosis water

systems, follow the manufacturer’s recommendations.

If the water supply to the refrigerator is from a Reverse

Osmosis Water Filtration System AND the refrigerator

also has a water filter, use the refrigerator’s filter bypass

plug. Using the refrigerator’s water filtration cartridge in

conjunction with the RO filter can result in hollow ice

cubes and slower water flow from the water dispenser.

This water line installation is not warranted by the

refrigerator or icemaker manufacturer. Follow these

instructions carefully to minimize the risk of expensive

water damage.

Water hammer (water banging in the pipes) in house

plumbing can cause damage to refrigerator parts and

lead to water leakage or flooding. Call a qualified

plumber to correct water hammer before installing

the water supply line to the refrigerator.

To prevent burns and product damage, do not hook

up the water line to the hot water line.

If you use your refrigerator before connecting the water

line, make sure the icemaker power switch is in the

(off)

position.

Do not install the icemaker tubing in areas where

temperatures fall below freezing.

All installations must be in accordance with local

plumbing code requirements.

WARNING – Connect to potable water

supply only.

BEFORE YOU BEGIN

• Copper or GE SmartConnect

™

Refrigerator Tubing

kit, 1/4″ outer diameter to connect the refrigerator

to the water supply. If using copper, be sure both

ends of the tubing are cut square.

To determine how much tubing you need: measure

the distance from the water valve on the back of the

refrigerator to the water supply pipe. Then add 8′

(2.4 m). Be sure there is sufficient extra tubing (about

8′ [2.4 m] coiled into 3 turns of about 10″ [25 cm]

diameter) to allow the refrigerator to move out from

the wall after installation.

GE SmartConnect

™

Refrigerator Tubing Kits are

available in the following lengths:

2′ (0.6 m) – WX08X10002

6′ (1.8 m) – WX08X10006

15′ (4.6 m) – WX08X10015

25′ (7.6 m) – WX08X10025

Be sure that the kit you select allows at least 8′ (2.4 m)

as described above.

WHAT YOU WILL NEED

NOTE: The only GE approved plastic tubing is that

supplied in GE SmartConnect™ Refrigerator Tubing

kits. Do not use any other plastic water supply line

because the line is under pressure at all times. Certain

types of plastic will crack or rupture with age and

cause water damage to your home.

• A GE water supply kit (containing tubing, shutoff

valve and fittings listed below) is available at extra

cost from your dealer or from Parts and Accessories,

800.626.2002.

• A cold water supply. The water pressure must be

between 20 and 120 p.s.i. (1.4–8.2 bar) on models

without a water filter and between 40 and 120 p.s.i.

(2.8–8.2 bar) on models with a water filter.

• Power drill.

• 1/2″ or adjustable wrench.

• Straight and Phillips blade screwdriver.

• Two 1/4″ outer diameter compression nuts and

2 ferrules (sleeves)—to connect the copper tubing

to the shutoff valve and the refrigerator water valve.

• If you are using a GE SmartConnect™ Refrigerator

Tubing kit, the necessary fittings are preassembled to

the tubing.

• If your existing copper water line has a flared fitting

at the end, you will need an adapter (available at

plumbing supply stores) to connect the water line to

the refrigerator OR you can cut off the flared fitting

with a tube cutter and then use a compression

fitting. Do not cut formed end from GE

SmartConnect™ Refrigerator tubing.

• Shutoff valve to connect to the cold water line.

The shutoff valve should have a water inlet with a

minimum inside diameter of 5/32″ at the point of

connection to the COLD WATER LINE. Saddle-type

shutoff valves are included in many water supply kits.

Before purchasing, make sure a saddle-type valve

complies with your local plumbing codes. Install the

shutoff valve on the nearest frequently used drinking

water line.

WHAT YOU WILL NEED (CONT.)

Installation Instructions

SHUT OFF MAIN WATER SUPPLY

Choose a location for the valve that is easily

accessible. It is best to connect into the side of a

vertical water pipe. When it is necessary to connect

into a horizontal water pipe, make the connection

to the top or side, rather than at the bottom,

to avoid drawing off any sediment from the

water pipe.

Drill a 1/4″ hole in the water pipe (even if using a

self-piercing valve) using a sharp bit. Remove any

burrs resulting from drilling the hole in the pipe.

Take care not to allow water to drain into the drill.

Failure to drill a 1/4″ hole may result in reduced

ice production or smaller cubes.

DRILL THE HOLE FOR THE VALVE

Fasten the shutoff valve to the cold water pipe with

the pipe clamp.

Tighten the clamp screws until the sealing washer

begins to swell.

NOTE: Do not overtighten or you may crush the

tubing.

NOTE: Commonwealth of Massachusetts Plumbing

Codes 248CMR shall be adhered to. Saddle valves

are illegal and use is not permitted in Massachusetts.

Consult with your licensed plumber.

FASTEN THE SHUTOFF VALVE

Vertical Cold

Water Pipe

Saddle-Type

Shutoff Valve

Pipe Clamp

Clamp Screw

Washer

Inlet End

Route the tubing between the cold water line and

the refrigerator.

Route the tubing through a hole drilled in the wall

or floor (behind the refrigerator or adjacent base

cabinet) as close to the wall as possible.

NOTE: Be sure there is sufficient extra tubing

(about 8′ [2.4 m] coiled into 3 turns of about 10″

[25 cm] diameter) to allow the refrigerator to move

out from the wall after installation

ROUTE THE TUBING

Place the compression nut and ferrule (sleeve) for

copper tubing onto the end of the tubing and

connect it to the shutoff valve.

Make sure the tubing is fully inserted into the valve.

Tighten the compression nut securely.

For plastic tubing from a GE SmartConnect™

Refrigerator Tubing kit, insert the molded end

of the tubing into the shutoff valve and tighten

compression nut until it is hand tight, then tighten

one additional turn with a wrench. Overtightening

may cause leaks.

CONNECT THE TUBING TO THE

VALVE

Turn the main water supply on and flush out the

tubing until the water is clear.

FLUSH OUT THE TUBING

NOTE: Commonwealth of Massachusetts Plumbing

Codes 248CMR shall be adhered to. Saddle valves

are illegal and use is not permitted in Massachusetts.

Consult with your licensed plumber.

Saddle-Type

Shutoff Valve

Compression Nut

SmartConnect™

Tubing

Packing Nut

Outlet Valve

Ferrule (sleeve)

NOTES:

• Before making the connection to the refrigerator,

be sure the refrigerator power cord is not

plugged into the wall outlet.

• If your refrigerator does not have a water filter,

we recommend installing one if your water supply

has sand or particles that could clog the screen of

the refrigerator’s water valve. Install it in the

water line near the refrigerator. If using a GE

SmartConnect™ Refrigerator Tubing kit, you

will need an additional tube (WX08X10002)

to connect the filter. Do not cut plastic tube

to install filter.

CONNECT THE TUBING TO THE

REFRIGERATOR

Installation Instructions

Place the compression nut and ferrule (sleeve)

onto the end of the tubing as shown. On a GE

SmartConnect

™

Refrigerator Tubing kit, the nuts

are already assembled to the tubing.

Insert the end of the tubing into the refrigerator

connection as far as possible. While holding the

tubing, tighten the fitting.

For plastic tubing from a GE SmartConnect

™

Refrigerator Tubing kit, insert the molded end of

the tubing into the refrigerator connection and

tighten the compression nut until it is hand tight,

then tighten one additional turn with a wrench.

Overtightening may cause leaks.

Fasten the tubing into the clamp provided as

shown to keep it in position. You may need to pry

open the clamp.

One of the illustrations below will look like the

connection on your refrigerator.

On models using the refrigeration connection at

the water valve, remove the plastic flexible cap.

CONNECT THE TUBING TO THE

REFRIGERATOR

(CONT.)

Some models have the refrigerator connection at

the end of tubing located outside the compressor

compartment access cover. On other models, the

compressor compartment access cover must be

removed in order to access the refrigerator

connection at the water valve.

1/4″

Compression

Nut

Tubing

Clamp

1/4″

Tubing

Refrigerator

Connection

SmartConnect™

Tubing

Ferrule

(sleeve)

Tighten any connections that leak.

TURN THE WATER ON AT THE

SHUTOFF VALVE

CONNECT THE TUBING TO THE

REFRIGERATOR

(CONT.)

Reattach the access cover.

SmartConnect™

Tubing

1/4″

Compression

Nut

1/4″

Tubing

Arrange the coil of tubing so that it does not vibrate

against the back of the refrigerator or against the

wall. Push the refrigerator back to the wall.

PLUG IN THE REFRIGERATOR

START THE ICEMAKER

Set the icemaker power switch to the

I (on)

position.

The icemaker will not begin to operate until it

reaches its operating temperature of 15°F (-9°C)

or below. It will then begin operation automatically

if the icemaker power switch is in the

I (on)

position.

NOTE: In lower water pressure conditions, the

water valve may turn on up to 3 times to deliver

enough water to the icemaker.

Tubing

Clamp

Refrigerator

Connection

Ferrule

(sleeve)

Consumer Support

Troubleshooting Tips Installation Instructions Safety InstructionsOperating Instructions

Normal operating sounds.

The new high efficiency compressor runs faster and will have a higher pitch hum

or pulsating sound while operating.

The fan circulating air inside the freezer which keeps the temperatures

throughout.

Water dropping on the defrost heater causing a sizzling, hissing or popping

sound during the defrost cycle.

The flow of refrigerant through the freezer cooling coils sounds like boiling

water or a gurgling noise.

Cracking or popping of cooling coils caused by expansion and contraction

during defrost and refrigeration following defrost.

Water dripping as it melts from the evaporator and flows to the drain pan

during the defrost cycle.

Icemaker (on some models)

The icemaker water valve will buzz when the icemaker fills with water. If the

power switch is in the

I (on)

position it will buzz even if it has not yet been hooked

up to water. Keeping the power switch in the

I (on)

position before it is hooked

up to water can damage the icemaker. To prevent this, set the power switch to the

O (off)

position. This will stop the buzzing.

The sound of cubes dropping into the bin and water running in pipes as

icemaker refills.

Troubleshooting Tips

Save time and money! Review the charts on the following

pages first and you may not need to call for service.

Problem Possible Causes What To Do

Refrigerator does not

Refrigerator in defrost cycle. • Wait about 30 minutes for defrost cycle to end.

operate

Freezer control • Move the freezer control to a temperature setting.

0 (off)

position.

Refrigerator is unplugged. • Push the plug completely into the outlet.

The fuse is blown/circuit •Replace fuse or reset the breaker.

breaker is tripped.

Refrigerator or freezer

Temperature control not set • See

About the controls.

compartment too warm

cold enough.

Warm weather or frequent • Set the temperature control one step colder.

door openings. See

About the controls.

Door left open. • Check to see if package is holding door open.

These sounds are normal and are due mostly to highly efficient operation.

Before you call for service…

Newer refrigerators sound different from older refrigerators. Modern refrigerators have

more features and use newer technology.

Do you hear what I hear? These sounds are normal.

Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions Installation Instructions

Problem Possible Causes What To Do

Vibration or rattling

Front rollers need adjusting. • See

Rollers.

Slight vibration is normal.

Motor operates for

Normal when refrigerator • Wait 24 hours for the refrigerator to completely

long periods or cycles

is first plugged in. cool down.

on and off frequently.

Often occurs when large • This is normal.

(Modern refrigerators

amounts of food are

with more storage

placed in refrigerator.

space and a larger

Door left open. • Check to see if package is holding door open.

freezer require more

Hot weather or frequent • This is normal.

operating time. They

door openings.

start and stop often

Temperature controls • See

About the controls.

to maintain even

set at the coldest

temperatures.)

setting.

Frost or ice crystals

Door left open. • Check to see if package is holding door open.

on frozen food

Too frequent or too long

(frost within package

door openings.

is normal)

Divider between

Automatic energy saver •This helps prevent condensation on the outside.

refrigerator and freezer

system circulates warm

compartments

liquid around front edge

feels warm

of freezer compartment.

Automatic icemaker

Icemaker power switch • Set the power switch to the

I (on)

position.

does not work

is in the

O (off)

position.

(on some models)

Water supply turned off or • See

Installing the water line.

not connected.

Freezer compartment • Wait 24 hours for the refrigerator to completely

too warm. cool down.

Piled up cubes in the storage •Level cubes by hand.

bin cause icemaker to shut off.

Ice cubes stuck in icemaker. • Turn off the icemaker, remove cubes, and turn the

(Green power light on icemaker back on.

icemaker blinking.)

Ice cubes have

Ice storage bin needs cleaning. • Empty and wash bin. Discard old cubes.

odor/taste

Food transmitting odor/taste • Wrap foods well.

to ice cubes.

Interior of refrigerator •See

Care and cleaning.

needs cleaning.

Small or hollow cubes

Water filter clogged. •Replace filter cartridge with new cartridge or with plug.

Slow ice cube freezing

Door left open. • Check to see if package is holding door open.

Temperature control not set •See

About the controls.

cold enough.

Door not closing

Door gasket on hinge side •Apply petroleum jelly on face of gasket.

properly

sticking or folding over.

Orange glow in freezer

Defrost heater is on. • This is normal.

Cube dispenser does not

Icemaker or water supply • Turn on icemaker or water supply.

work (on some models)

turned off.

Ice cubes are frozen to • Remove cubes.

icemaker feeler arm.

Irregular ice clumps in • Break up with fingertip pressure and discard

storage container. remaining clumps.

•Freezer may be too warm. Adjust the freezer control

to a colder setting, one position at a time, until clumps

do not form.

Dispenser is LOCKED. • Press and hold the LOCK CONTROL pad for 3 seconds.

www.Hotpoint.com

Problem Possible Causes What To Do

Water has poor taste/odor

Water dispenser has not been •Dispense water until all water in system is replenished.

(on some models)

used for a long time.

Water in first glass is

Normal when refrigerator •Wait 24 hours for the refrigerator to completely

warm (on some models)

is first installed. cool down.

Water dispenser has not been • Dispense water until all water in system is replenished.

used for a long time.

Water system has been drained. •Allow several hours for replenished supply to chill.

Water dispenser does

Water supply line turned • See

Installing the water line.

not work (on some models)

off or not connected.

Water filter clogged. • Replace filter cartridge or remove filter and install plug.

Air may be trapped in the •Press the dispenser arm for at least two minutes.

water system.

Dispenser is LOCKED. • Press and hold the LOCK CONTROL pad for 3 seconds.

Water spurting from

Newly-installed filter cartridge. •Run water from the dispenser for 3 minutes (about

dispenser

⁄2 gallons).

Water is not dispensed

Water in reservoir is frozen. • Call for service.

No water or ice cube

Supply line or shutoff • Call a plumber.

production

valve is clogged.

Water filter clogged. •Replace filter cartridge or remove filter and install plug.

Dispenser is LOCKED. • Press and hold the LOCK CONTROL pad for 3 seconds.

Refrigerator has odor

Foods transmitting • Foods with strong odors should be tightly wrapped.

odor to refrigerator.

• Keep an open box of baking soda in the refrigerator;

replace every three months.

Interior needs cleaning. • See

Care and cleaning.

Defrost water drainage •See

Care and cleaning.

system needs cleaning.

Moisture forms on

Not unusual during •Wipe surface dry.

outside of refrigerator

periods of high humidity.

Moisture collects inside

Too frequent or too

long door openings.

Interior light does

No power at outlet. • Replace fuse or reset the breaker.

not work

Light bulb burned out. •See

Replacing the light bulbs.

Water on kitchen floor or

Drain in the bottom of • See

Care and cleaning.

on bottom of freezer

the freezer clogged.

Cubes jammed in chute. •Poke ice through with a wooden spoon.

Hot air from bottom

Normal air flow cooling motor.

of refrigerator

In the refrigeration process,

it is normal that heat be expelled

in the area under the refrigerator.

Some floor coverings are sensitive

and will discolor at these normal

and safe temperatures.

CUBED ICE was selected

Last setting was

CRUSHED ICE

. • A few cubes were left in the crusher from the previous

but CRUSHED ICE was

setting. This is normal.

dispensed (

on some models)

Frequent “buzzing” sound

Icemaker power switch is in the • Set the power switch to the

O (off)

position. Keeping it in

I (on)

position but the water supply the

I (on)

position will damage the water valve.

to the refrigerator has not been

connected.

Consumer Support

Troubleshooting Tips Installation Instructions Safety InstructionsOperating Instructions

Before you call for service…

TERMS AND CONDITIONS:

This warranty applies only for single family domestic use in

Canada when the Refrigerator has been properly installed

according to the instructions supplied by Mabe and is

connected to an adequate and proper utility service.

Damage due to abuse, accident, commercial use, and alteration

or defacing of the serial plate cancels all obligations of this

warranty.

Service during this warranty period must be performed by an

Authorized Mabe Service Agent.

Neither Mabe nor the Dealer is liable for any claims or

damages resulting from failure of the Refrigerator or from

service delays beyond their reasonable control.

To obtain warranty service, purchaser must present the original

Bill of Sale. Components repaired or replaced are warranted

through the remainder of the original warranty period only.

This warranty is extended to the original purchaser and any

succeeding owner for products purchased for home use within

Canada. In home warranty service will be provided in areas

where it is available and deemed reasonable by Mabe

to provide.

This warranty is in addition to any statutory warranty.

WHAT IS NOT COVERED:

• Owner is responsible to pay for service calls related to

product installation and/or teaching how to use the product.

• Damage to finish must be reported within 48 hours following

the delivery of the appliance.

• Damage to finish after delivery.

• Improper installation—proper installation includes adequate

air circulation to the refrigeration system, adequate electrical,

plumbing and other connecting facilities.

• Replacement of house fuses or resetting of circuit breakers.

• Replacement of light bulbs.

• Damage to product caused by accident, fire, floods or acts

of God.

• Loss of food due to spoilage.

• Proper use and care of product as listed in the owner’s

manual, proper setting of controls.

• Product not accessible to provide required service.

• WARRANTOR IS NOT RESPONSIBLE FOR CONSEQUENTIAL

DAMAGES.

IMPORTANT

Keep this warranty and your bill of sale as proof of original purchase and purchase date.

Please have serial number and model number available when calling for service.

Mabe Service is available coast to coast. If further help is

needed concerning this warranty, contact:

Manager, Consumer Relations

Mabe Canada Inc., Consumer Service

1 Factory Lane, Suite 310

Moncton, New Brunswick E1C 9M3

1.800.361.3400

Staple your receipt here.

Proof of the original purchase

date is needed to obtain service

under the warranty.

What is covered How Long Warranted Parts Labour

(From Date of Sale) Repair or Replace

at Mabe’s Option

Compressor GE Profile: Ten (10) Years GE Profile: Ten (10) Years GE Profile: Five (5) Years

GE and All Other GE and All Other GE and All Other

Brands: One (1) Year Brands: One (1) Year Brands: One (1) Year

Sealed System (including GE Profile: Five (5) Years GE Profile: Five (5) Years GE Profile: Five (5) Years

evaporator, condenser GE and All Other GE and All Other GE and All Other

tubing and refrigerant) Brands: One (1) Year Brands: One (1) Year Brands: One (1) Year

All Other Parts One (1) Year One (1) Year One (1) Year

CUSTOMER WARRANTY

(for customers in Canada)

Your refrigerator is warranted to be free of defects in material and workmanship.

EXCLUSION OF IMPLIED WARRANTIES—Your sole and exclusive remedy is product repair as provided in this Limited

Warranty. Any implied warranties, including the implied warranties of merchantability or fitness for a particular purpose,

are limited to one year or the shortest period allowed by law.

Consumer Support

Troubleshooting Tips Installation Instructions Safety InstructionsOperating Instructions

This warranty is extended to the original purchaser and any succeeding owner for products purchased for home

use within the USA. If the product is located in an area where service by a GE Authorized Servicer is not available,

you may be responsible for a trip charge or you may be required to bring the product to an Authorized GE Service

location for service. In Alaska, the warranty excludes the cost of shipping or service calls to your home.

Some states do not allow the exclusion or limitation of incidental or consequential damages. This warranty gives

you specific legal rights, and you may also have other rights which vary from state to state. To know what your

legal rights are, consult your local or state consumer affairs office or your state’s Attorney General.

Warrantor: General Electric Company. Louisville, KY 40225

Refrigerator Warranty. (For customers in the United States)

All warranty service provided by our Factory Service Centers,

or an authorized Customer Care

technician. To schedule service,

on-line, 24 hours a day, visit us at www.Hotpoint.com, or call

800.GE.CARES (800.432.2737). Please have serial number and

model number available when calling for service.

For The Period Of: We Will Replace:

One Year Any part

of the refrigerator which fails due to a defect in materials or workmanship.

From the date of the

During this

limited one-year warranty,

we will also provide,

free of charge,

all labor and

original purchase

related service to replace the defective part.

Thirty Days Any part

of the water filter cartridge which fails due to a defect in materials or workmanship.

(Water filter, if included)

During this

limited thirty-day warranty,

we will also provide,

free of charge,

a replacement water

From the original

filter cartridge.

purchase date of

the refrigerator

■ Service trips to your home to teach you how to use

the product.

■ Improper installation, delivery or maintenance.

■ Failure of the product if it is abused, misused, or used for

other than the intended purpose or used commercially.

■ Loss of food due to spoilage.

■ Replacement of house fuses or resetting of circuit

breakers.

■ Damage caused after delivery.

■ Replacement of the water filter cartridge, if included,

due to water pressure that is outside the specified

operating range or due to excessive sediment in the

water supply.

■ Replacement of the light bulbs, if included, or water filter

cartridge, if included, other than as noted above.

■ Damage to the product caused by accident, fire, floods

or acts of God.

■ Incidental or consequential damage caused by possible

defects with this appliance.

■ Product not accessible to provide required service.

What Is Not Covered:

Staple your receipt here.

Proof of the original purchase

date is needed to obtain service

under the warranty.

EXCLUSION OF IMPLIED WARRANTIES—Your sole and exclusive remedy is product repair as provided in this

Limited Warranty. Any implied warranties, including the implied warranties of merchantability or fitness for a

particular purpose, are limited to one year or the shortest period allowed by law.

Manufactured for: General Electric Company, Louisville, KY 40225

EPA EST. No. 070595-MN-001

Performance Data Sheet

SmartWater Filtration System

MWF Cartridge

This system has been tested according to NSF/ANSI 42/53 for reduction of the substances listed below.

The concentration of the indicated substances in water entering the system was reduced to a concentration

less than or equal to the permissible limit for water leaving the system, as specified in NSF/ANSI 42/53.*

(100% safety factors built in for unmetered usage)

Standard No. 42: Aesthetic Effects

Parameter USEPA Influent Influent Effluent % Reduction Min. Required

MCL Challenge Concentration Average Average Maximum Average Minimum Reduction

Chlorine — 2.0 mg/L + 10% 1.96 mg/L 0.06 mg/L 0.11 mg/L 96.77% 94.74% > 50%

T & O — — — — — — — —

Particulate** — ≥ 10,000 particles/mL 6,400,000 #/mL 58,833 #/mL 150,000 #/mL 99.14% 97.97% ≥ 85%

Standard No. 53: Health Effects

Parameter USEPA Influent Influent Effluent % Reduction Min. Required

MCL Challenge Concentration Average Average Maximum Average Minimum Reduction

Turbidity 0.5 NTU 11 + 1 NTU*** 10.5 NTU 0.14 NTU 0.28 NTU 98.54% 97.20% 0.5 NTU

Cysts ≥ 99.95% Reduction Minimum 50,000 L 118,750 #/L < 1 #/L 4 #/L > 99.99% > 99.99% ≥ 99.95%

Asbestos ≥ 99% Reduction 10

to 10

fibers/L; > 10µm 57 MF/L 0.996 MF/L < 1 MF/L 99.60% 99.39% ≥ 99%

Lead at pH 6.5 0.015 mg/L 0.15 mg/L + 10% 0.1567 mg/L < 0.001 mg/L < 0.001 mg/L 99.36% 99.29% 0.010 mg/L

Lead at pH 8.5 0.015 mg/L 0.15 mg/L + 10% 0.1433 mg/L < 0.001 mg/L < 0.001 mg/L 99.30% 99.29% 0.010 mg/L

Mercury at pH 6.5 0.002 mg/L 0.006 mg/L + 10% 0.0059 mg/L 0.000350 mg/L 0.0007 mg/L 94.70% 87.50% 0.002 mg/L

Mercury at pH 8.5 0.002 mg/L 0.006 mg/L + 10% 0.0057 mg/L 0.000325 mg/L 0.0006 mg/L 93.20% 89.29% 0.002 mg/L

Alachlor 0.002 mg/L 0.04 mg/L + 10% 0.0367 mg/L 0.00023 mg/L 0.0004 mg/L 99.34% 98.67% 0.002 mg/L

Lindane 0.0002 mg/L 0.002 mg/L + 10% 0.0020 mg/L < 0.00002 mg/L < 0.00002 mg/L 99.00% 98.95% 0.0002 mg/L

2,4-D 0.070 mg/L 0.210 mg/L + 10% 0.2033 mg/L 0.00337 mg/L 0.011000 mg/L 98.32% 94.50% 0.070 mg/L

Toxaphene 0.003 mg/L 0.015 mg/L + 10% 0.0160 mg/L 0.00100 mg/L 0.001000 mg/L 93.44% 91.67% 0.003 mg/L

Benzene 0.005 mg/L 0.015 mg/L + 10% 0.0145 mg/L 0.000500 mg/L 0.000500 mg/L 96.51% 95.83% 0.005 mg/L

Carbofuran 0.040 mg/L 0.080 mg/L + 10% 0.0830 mg/L 0.001000 mg/L 0.001000 mg/L 98.78% 98.65% 0.04 mg/L

1,4 dichlorobenzene

0.075 mg/L 0.225 mg/L + 10% 0.2283 mg/L 0.000500 mg/L 0.000500 mg/L 99.78% 99.77% 0.075 mg/L

Atrazine 0.003 mg/L 0.009 mg/L + 10% 0.0087 mg/L < 0.0005 mg/L < 0.0005 mg/L 94.22% 93.33% 0.003 mg/L

* Tested using a flow rate of 0.50 gpm; pressure of 60 psig; pH of 7.5 ± 0.5; temp. of 68° ± 5°F (20° ± 3°C)

** Measurement in Particles/ml. Particles used were 0.5-1 microns

*** NTU=Nephelometric Turbidity units

Operating Specifications

 Capacity: certified for up to 300 gallons (1135 l); up to six

months for models without a replacement filter indicator light;

up to one year for models with a replacement filter indicator light

 Pressure requirement: 40–120 psi (2.8–8.2 bar), non-shock

 Temperature: 33–100ºF (0.6–38ºC)

 Flow rate: 0.5 gpm (1.9 lpm)

General Installation/Operation/Maintenance Requirements

 Flush new cartridge at full flow for 3 minutes to purge out

trapped air.

 Replace cartridge when the indicator light flashes or water

flow rate is reduced on non-indicator units.

Special Notices

 Installation instructions, parts and service availability, and standard

warranty are included with the product when shipped.

 This drinking water system must be maintained according to

manufacturer’s instructions, including replacement of filter cartridges.

 Do not use with water that is microbiologically unsafe or of unknown

quality without adequate disinfection before or after the system.

Systems certified for cyst reduction may be used on disinfected water

that may contain filterable cysts.

 The contaminants or other substances removed or reduced by this

water treatment system are not necessarily in your water.

 Check for compliance with the state and local laws and regulations.

 Note that while the testing was performed under standard laboratory

conditions, actual performance may vary. Systems must be installed and

operated in accordance with manufacturer’s recommended procedures

and guidelines.

NSF

System Tested and Certified by NSF International against

ANSI/NSF Standard 42 & 53 for the reduction of:

State of California

Department of Health Services

Water Treatment Device

Certificate Number

Date Issued: February 2, 2005

Trademark/Model Designation

Replacement Elements

169805 -

MWF MWF

Manufacturer: General Electric Company

The water treatment device(s) listed on this certificate have met the testing requirements pursuant to Section

116830 of the Health and Safety Code for the following health related contaminants:

Cysts

Turbidity

Asbestos

Lead

Mercury

Alachlor

Atrazine

Benzene

Carbofuran

Lindane

Mercury

Toxaphene

1,4-dichlorobenzene

2,4-D

Microbiological Contaminants and Turbidity

Inorganic/Radiological Contaminants

Organic Contaminants

Do not use where water is microbiologically unsafe or with water of unknown quality, except that systems certified for

cyst reduction may be used on disinfected waters that may contain filterable cysts.

300 galRated Service Capacity:

0.5 gpm

Rated Service Flow:

Conditions of Certification:

Standard No. 42: Aesthetic Effects

Chemical Unit

Chlorine Taste and Odor

Mechanical Filtration Unit

Particulate Reduction, Class I

Standard No. 53: Health Effects

Chemical Reduction Unit

Alachlor and Atrazine Reduction

Benzene and Carbofuran Reduction

1,4 dichlorobenzene and 2,4-D Reduction

Lead and Lindane Reduction

Mercury and Toxaphene Reduction

Mechanical Filtration Unit

Turbidity Reduction

Cyst and Asbestos Reduction

GE Service Protection Plus

™

GE, a name recognized worldwide for quality and dependability, offers you

Service Protection Plus

™

—comprehensive protection on all your appliances—

No Matter What Brand!

Benefits Include:

• Backed by GE

• All brands covered

• Unlimited service calls

• All parts and labor costs included

• No out-of-pocket expenses

• No hidden deductibles

• One 800 number to call

You will be completely satisfied with our service protection or you may request your money back

on the remaining value of your contract. No questions asked. It’s that simple.

Protect your refrigerator, dishwasher, washer and dryer, range, TV, VCR and much more—any brand!

Plus there’s no extra charge for emergency service and low monthly financing is available. Even icemaker

coverage and food spoilage protection is offered. You can rest easy, knowing that all your valuable

household products are protected against expensive repairs.

Place your confidence in GE and call us in the U.S. toll-free at 800.626.2224

for more information.

*All brands covered, up to 20 years old, in the continental U.S.

We’ll Cover Any Appliance.

Anywhere. Anytime.*

Consumer Product Ownership Registration

Dear Customer:

Thank you for purchasing our product and thank you for placing your confidence in us.

We are proud to have you as a customer!

Follow these three steps to protect your new appliance investment:

Model Number Serial Number

Complete and mail

your Consumer

Product Ownership

Registration today.

Have the peace of

mind of knowing we

can contact you in

the unlikely event of

a safety modification.

After mailing the

registration below,

store this document

in a safe place.

It contains information

you will need should

you require service.

Our service number

in the USA is:

800.GE.CARES

(800.432.2737).

Read your Owner’s

Manual carefully.

It will help you

operate your new

appliance properly.

La page est en cours de chargement...

Hotpoint HSS25IFPCC Le manuel du propriétaire

Marque: Hotpoint

Modèle: HSS25IFPCC

Catégorie: Frigos

Taper: Le manuel du propriétaire

Ce manuel convient également à

HSS25IFPWW

Télécharger le PDF

rapport

dans d''autres langues

English: Hotpoint HSS25IFPCC Owner's manual
español: Hotpoint HSS25IFPCC El manual del propietario

Hotpoint HSS25IFPCC Le manuel du propriétaire

Ce manuel convient également à

Hotpoint HSS25IFPCC Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents