GE PDW8800JBB Manuel utilisateur

Marque: GE

Modèle: PDW8800JBB

Catégorie: Lave-vaisselle

Taper: Manuel utilisateur

PDW8000 Series
PDW9000 Series
Owner’s Manual
Dishwashers
165D4700P335 49-55015-3     03-07 JR
Safety Instructions  . . . . . . . . . . 2, 3
Operating Instructions
Care and Cleaning  . . . . . . . . . . . . . . . . 15
Control Panel and Settings  . . . . . . . 4–7
Flashing Display Lights . . . . . . . . . . . . . .7
Loading Place Settings  . . . . . . . . . . . . 14
Loading the Racks . . . . . . . . . . . . . 12–14
Using the Dishwasher  . . . . . . . . . . .8–11
Troubleshooting Tips  . . . . . 16–18
Consumer Support
Consumer Support  . . . . . . . . . . . . . . . .24 
Product Registration  . . . . . . . . . . .19, 20
Warranty  . . . . . . . . . . . . . . . . . . . . . . . . . 23
ge.com
Write the model and serial 
numbers here:
Model # __________________
Serial # __________________
You can find them on the tub wall 
just inside the door.
GE Profile
™

Operating Instructions Safety Instructions

Consumer Support

Troubleshooting Tips

IMPORTANT SAFETY INFORMATION.

READ ALL INSTRUCTIONS BEFORE USING —

SAVE THESE INSTRUCTIONS

WARNING!

For your safety, the information in this manual must be followed to minimize the risk of fire

or explosion, electric shock, and to prevent property damage, personal injury, or death.

WATER HEATER SAFETY

PROPER INSTALLATION AND MAINTENANCE

This dishwasher must be properly installed and located in accordance with the Installation

Instructions before it is used. If you did not receive an Installation Instructions sheet with

your dishwasher, you can receive one by visiting our website at ge.com.

■ Contents washed in Anti-bacterial mode, if

available, may be hot to the touch. Use care

before handling.

■ Using a detergent that is

not specifically designed

for dishwashers will cause

the dishwasher to fill with

suds.

■ If your dishwasher is connected to a

wall switch, ensure that the switch is

on prior to use.

■ On dishwashers with electronic

controls, if you choose to turn the wall

switch off between wash cycles, allow

5–10 seconds after turning the switch on before

touching START/RESET to allow the control to

reboot.

■ Non-Dishware Items: Do not wash items such

as electronic air cleaner filters, furnace filters and

paint brushes in your dishwasher. Damage to

dishwasher and discoloration or staining of

dishwasher may result.

■ Close supervision is necessary if this appliance

is used by or near children.

■ Load light, plastic items so they will not

become dislodged and drop to the bottom

of the dishwasher—they might come into

contact with the heating element and be

damaged.

■ Connect to a grounded metal, permanent wiring

system; or run an equipment-grounding

conductor with the circuit conductors and

connect to the equipment-grounding terminal

or lead of the appliance.

■ Improper connection of the equipment-grounding

conductor can result in a risk of electric shock.

Check with a qualified electrician or service

representative if you are in doubt whether the

appliance is properly grounded.

■ Dispose of discarded appliances and shipping

or packing material properly.

■ Do not attempt to repair or replace any part

of your dishwasher unless it is specifically

recommended in this manual. All other servicing

should be referred to a qualified technician.

■ To minimize the possibility of electric shock,

disconnect this appliance from the power supply

before attempting any maintenance.

NOTE: Turning the dishwasher off does not

disconnect the appliance from the power supply.

We recommend having a qualified technician

service your appliance.

WARNING!

CAUTION: To prevent minor injury or property damage

Under certain conditions, hydrogen gas may be produced in a water heater that has not been used

for two weeks or more. HYDROGEN GAS IS EXPLOSIVE.

If the hot water has not been used for two weeks or more, prevent the possibility of damage or injury

by turning on all hot water faucets and allow them to run for several minutes. Do this before using any

electrical appliance which is connected to the hot water system. This simple procedure will allow any built-

up hydrogen gas to escape. Since the gas is flammable, do not smoke or use an open flame or appliance

during this process.

WARNING! RISK OF CHILD ENTRAPMENT

PROPER DISPOSAL OF THE DISHWASHER

Junked or abandoned dishwashers are dangerous…

even if they will sit for “just a few days.” If you are

getting rid of your old dishwasher, please follow

the instructions to help prevent accidents.

Before You Throw Away Your Old Dishwasher

Take off the door of the washing compartment or

remove the door latch (as shown).

NOTE: PDW9200–PDW9900 Series models also have a

latch screw which must be removed (Step 1) as shown.

Consumer Support

Troubleshooting TipsOperating InstructionsSafety Instructions

ge.com

Screw

(

on some

models)

■ Use this appliance only for its intended purpose

as described in this Owner's Manual.

■ Use only powder, tabs, liquid detergents or rinse

agents recommended for use in a dishwasher and

keep them out of the reach of children. Cascade

Cascade

Complete and Electrasol

Automatic

Dishwashing Detergents, and Jet-Dry

and

Cascade Crystal Clear

rinse agents have been

approved for use in all GE dishwashers.

■ Do not mix any chlorine bleach-based automatic

dishwashing detergent with any dishwashing

detergent containing enzymes as this could

cause the detergents to congeal and lead to

blockage of the SmartDispense

system.

■ Locate sharp items so that they are not likely

to damage the door seal.

■ Load sharp knives with the handles up to reduce

the risk of cut-type injuries.

■ Do not wash plastic items unless marked

dishwasher safe or the equivalent. For plastic

items not so marked, check the manufacturer's

recommendations.

■ Do not touch the heating element during or

immediately after use.

■ Do not operate your dishwasher unless all

enclosure panels are properly in place.

■ Do not tamper with controls.

■ Do not abuse, sit on or stand on the door or dish

rack of the dishwasher.

■ Do not allow children to play around dishwasher

when opening or closing door due to the possibility

of small fingers being pinched in door.

■ Do not discard a dishwasher without first removing

the door of the washing compartment or the door

latch.

■ Do not store or use combustible materials, gasoline

or other flammable vapors and liquids in the

vicinity of this or any other appliance.

■ Do not allow children to play with, on or inside this

appliance or any discarded appliance.

WARNING!

When using your dishwasher, follow basic precautions,

including the following:

READ AND FOLLOW THIS SAFETY INFORMATION

CAREFULLY.

SAVE THESE INSTRUCTIONS

Operating Instructions Safety Instructions

Consumer Support

Troubleshooting Tips

About the dishwasher control panel.

You can locate your model number on the tub wall just inside the door. Throughout this manual, features and appearance may vary from your model.

Control Settings

Status Indicator Lights (Indicators vary by models)

The Status display tells you what is happening while the dishwasher is in operation and may flash,

indicating a malfunction. The lights will come ON indicating the sequence of the dishwasher operation.

LOW DETERGENT Displayed when the SmartDispense

needs to be refilled with liquid or gel automatic

dishwasher detergent.

NOTE: If you are not using SmartDispense

and you want to turn the LOW DETERGENT

LED light off, press the ADDED HEAT pad 5 times within 3 seconds. You will hear 3

beeps; then the light will go off. You can turn the light back on by pressing the ADDED

HEAT pad 5 times within 3 seconds.

SENSING Displayed while the Clean Sensor

is measuring the amount of soil and temperature

of water. The dishwasher will adjust the selected cycle to achieve optimal performance.

ADD-A-DISH Displayed during prewash, indicating that dishes added now will still be cleaned.

WASHING Displayed during prewash, main wash and rinse periods.

RINSING Displayed during rinse periods.

DRYING Displayed during HEATED DRY.

SANITIZED Displayed when cycle has met sanitization conditions.

CLEAN Displayed when a wash cycle is complete.

Time Remaining Display (on some models)

During operation, the display shows the minutes remaining until the cycle is complete. The display may

adjust the remaining time while the Sensing light is on. The time displayed at the start of each cycle may

change from the factory setting as the unit customizes itself to home use. During a delay start, the display

will show hours of time remaining until the cycle starts.

Selections

PDW8000 Series: Press the pad for the desired wash cycle.

PDW9000 Series: Use the Arrow Pads to scroll through the wash cycles.

NOTE: All cycle times and water usage information contained in the following section are approximate

values. Actual results will depend on several factors, including but not limited to inlet temperature,

household water pressure and amount of soil in the wash water.

The light above or next to the selected pad will be ON to indicate which WASH CYCLE has been selected.

3 45

PDW8100 Series–PDW8900 Series

LOW DETERGENT

Smart Dispense

ENSING

ASHING

RYING

ANITIZED

LEAN

INSE

NLY

INGLE

ACK

ASH

LASTIC

YCLE

HINA

YCLE

PEED

YCLE

ORMAL

COOKWARE

ANTI-BACTERIAL

62 43

PDW9200 Series–PDW9900 Series

Selections (continued)

ANTI-BACTERIA Heavy 8.8 gal., 105 min.

Medium 7.5 gal., 95 min.

Light 6.3 gal., 85 min.

This cycle raises the water temperature in the final rinse to sanitize your dishware. The

cycle length will vary depending on the temperature of your inlet water.

NOTE: The Anti-Bacteria cycle is monitored for sanitization requirements. If the cycle is

interrupted during or after the main wash portion or if the incoming water temperature is

so low that adequate water heating cannot be achieved, the sanitizing conditions may

not be met. In these cases, the sanitized light will not illuminate at the end of the cycle.

NOTE: NSF-certified residential dishwashers are not intended for licensed food

establishments

COOKWARE Heavy 10.0 gal., 80 min.

(POTS & PANS) Medium 8.8 gal., 70 min.

Light 7.5 gal., 60 min.

This cycle is meant for heavily soiled dishes or cookware with dried-on or baked-on soils.

This cycle may not remove burned-on foods. Everyday dishes are safe to be used in

this cycle.

NORMAL WASH Heavy 8.8 gal., 70 min.

Medium 7.5 gal., 60 min.

Light 5.0 gal., 50 min.

This cycle is for medium/heavily soiled dishes and glassware.

SPEED CYCLE 7.5 gal., 35 min.

(on some models)

This cycle is for everyday dishes and glassware.

CHINA CRYSTAL 7.5 gal., 35 min.

This cycle is for lightly soiled china and crystal.

GLASSES 7.5 gal., 30 min.

(on some models)

This cycle is specifically designed for glasses.

PLASTICS CYCLE Heavy 8.8 gal., 120 min.

(on some models) Medium 7.5 gal., 105 min.

Light 5.0 gal., 90 min.

The longer time for this cycle includes a built-in drying portion that is specifically

designed to reduce the risk of melting plastic items and improve plastic drying.

For removing red tomato-based stains, GE recommends the use of Cascade

Plastic Booster

SINGLE RACK WASH Heavy 8.2 gal., 70 min.

(on some models) Medium 7.0 gal., 60 min.

Light 4.6 gal., 50 min.

This cycle washes lightly soiled dishes on the upper rack only.

RINSE ONLY 2.5 gal., 10 min.

For rinsing partial loads that will be washed later. Do not use detergent with this cycle.

NOTE: On the PDW8000 Series models, the CHINA CRYSTAL/PLASTICS selector is a toggle pad; push pad

to switch between CHINA CRYSTAL and PLASTICS.

NOTE: This dishwasher is equipped with CleanSensor

with automatic temperature control; therefore,

cycle length and time may vary depending on soil and water temperature conditions.

NOTE: Only the Anti-Bacteria cycle has been designed to meet the requirements of Section 6, NSF 184 for

soil removal and sanitization efficacy.

Consumer Support

Troubleshooting TipsOperating InstructionsSafety Instructions

ge.com

Enhancements

The light above the selected pad will be ON to indicate which ENHANCEMENT has been selected.

DELAY HOURS You can delay the start of a wash cycle for up to 24 hours (depending on model). Press

the DELAY START pad to choose the number of hours you want to delay the start of

the cycle; then press START/RESET.

PDW8000 Series: The machine will count down and start automatically at the

correct time.

PDW9000 Series: After closing the door, the machine will count down and

automatically start at the correct time.

NOTE: To cancel the DELAY START selection before the cycle begins, repeatedly press

the DELAY START pad until the display is blank.

ADDED HEAT When selected, the cycle will run longer with heating element on to improve both wash

(EXTRA HOT WASH) and dry performance.

NOTE: Cannot be selected with RINSE ONLY cycle.

PRE WASH For use with heavily soiled and/or dried-on, baked-on soils. This option MUST be

(on some models) selected PRIOR to starting the cycle. This option adds 15 minutes to the cycle time.

NOTE: Cannot be selected with RINSE ONLY cycle.

HEATED DRY Shuts off the drying heat option. Dishes will air dry naturally (PDW8900 Series) or

Light Off fan dry (PDW9200–PDW9900 Series) to save energy.

HEATED DRY Turns the heater on for fast drying. This will extend the total cycle time by 15 minutes

Light On for the ANTI-BACTERIAL cycle, 38 minutes for the NORMAL, SINGLE RACK WASH

and COOKWARE cycles, 8 minutes for the SPEED cycle, 15 minutes for the

PLASTICS cycle and 30 minutes for all other cycles.

NOTE: Cannot be selected with RINSE ONLY cycle.

LOCK You can lock the controls to prevent any selections from being made. Or you can lock

the controls after you have started a cycle.

Children cannot accidentally start dishwasher by touching pads with this option

selected.

To unlock the dishwasher controls, press and hold the HEATED DRY pad for 3 seconds.

The light above the lock pad will turn off. To lock the dishwasher, press and hold the

HEATED DRY pad for 3 seconds. The light above the LOCK pad will turn on.

RESET To change a cycle after washing starts…

PDW8000 Series: Touch the START/RESET pad to cancel the cycle. The START/RESET light

will flash while the water is pumped out if needed. This takes approximately 2 minutes.

PDW9000 Series: Open the door slowly to prevent splash-out. Touch the START/RESET

pad to cancel the cycle. If the START/RESET light is flashing, close the door until the

water pumps out (this takes approximately 2 minutes) and the light stops flashing.

When the light stops flashing, the dishwasher can be reprogrammed and restarted.

Start

PDW8000 Series

Close and latch the dishwasher door and select the cycle and desired enhancements. Touch the

START/RESET pad to begin the cycle. Water fill begins immediately, and approximately 60 seconds later

the wash action begins.

When the dishwasher door is fully closed and latched, the control panel lights will display the last settings

you selected. If you don’t want to change any of the settings, simply touch the START/RESET pad to

begin the cycle.

If the door is closed, the indicator lights will turn off if the START/RESET pad is not selected within 5 minutes.

To activate the display, open and close the door or press any pad.

Operating Instructions Safety Instructions

Consumer Support

Troubleshooting Tips

About the dishwasher control panel.

Consumer Support

Troubleshooting TipsOperating InstructionsSafety Instructions

Flashing display lights.

Status Indicator Lights What It Means

START/RESET Cycle has been interrupted by pressing the START/RESET pad, or there

has been a power failure. Light will stop flashing after the dishwasher

automatically drains out the water. The dishwasher will restart if the

interruption was the result of a power failure.

Recommended dishwasher products.

GE recommends the following products for use in its

dishwashers:

■ For your manual detergent dispenser, Cascade

and Electrasol

powder, liquid or gel automatic

dishwasher detergents are approved.

■ For your SmartDispense

Detergent Dispenser, use

only the recommended detergents listed on page

10 of this manual.

■ Jet Dry

or Cascade Crystal Clear

rinse agents

to remove spots and prevent new film buildup on

your dishes, glasses, flatware, cookware and

plastic. Using rinse agent also improves dry

performance.

■ Cascade

Plastic Booster

to remove red staining

inside your dishwasher that can come from some

tomato-based foods.

■ Cerama Bryte

Stainless Steel Appliance Cleaner

to clean the exterior stainless steel panel of GE and

Profile

dishwashers (for stainless steel exterior

models only).

ge.com

Start (continued)

PDW9000 Series

After selecting the cycle and desired enhancements, touch the START/RESET pad to ready the

dishwasher to begin the cycle. Close the door to start the cycle or begin the DELAY START countdown.

When the cycle starts, the water fill begins and approximately 60 seconds later the wash action begins.

The dishwasher will always display your last selection and enhancements. If you don’t want to change

the settings, simply touch the START/RESET pad to ready the dishwasher and close the door to begin

the cycle.

Also, if a power failure occurs NORMAL and HEATED DRY will automatically be programmed. Make any

new selections and touch the START/RESET pad to begin the new cycle.

When the door is opened, the indicator lights will turn off if the START/RESET pad is not selected within

5 minutes. To activate the display, open and close the door or touch any pad.

Clean

PDW8000 Series

The CLEAN light is illuminated when the selected cycle and enhancements are complete. The light will

stay ON until a pad is pressed or the door is opened and then closed.

PDW9200 Series–PDW9900 Series

The CLEAN light is illuminated and a double beep will sound when the selected cycle and enhancements

are complete. You may remove the dishes at any time. The high-efficiency fan will run quietly for 30

minutes to 4 hours (depending on selected cycle) after the CLEAN light is illuminated to continue drying

the dishes. The fan can be turned off by opening the door and pressing any keypad.

ALL MODELS: To turn off the audible end-of-cycle signal (or re-activate it if it was previously turned off),

press the HEATED DRY pad 5 times within 3 seconds. A triple beep will sound to indicate the end-of-cycle

beep option has been toggled.

Operating Instructions Safety Instructions

Consumer Support

Troubleshooting Tips

Using the dishwasher.

The entering water should be at least 120°F and not more than 150°F for effective cleaning and to

prevent dish damage. Check the water temperature with a candy or meat thermometer. Turn on the

hot water faucet nearest the dishwasher, place the thermometer in a glass and let the water run

continuously into the glass until the temperature stops rising.

Check the Water Temperature

Jet-Dry

or Cascade Crystal Clear

rinse agent improves drying, removes spots and prevents new

film buildup on your dishes, glasses, flatware, cookware and plastic.

Use Jet-Dry

or Cascade Crystal Clear

Rinse Agent

Filling the Dispenser

The rinse agent dispenser holds 3.5 oz. of rinse agent.

Under normal conditions, this will last approximately

one month. Try to keep it full, but do not overfill.

Make sure the dishwasher door is fully open.

Turn the dispenser

cap to the left and

lift it out.

Add rinse agent until

the indicator window

looks full.

Clean up any spilled

rinse agent with a

damp cloth.

Replace the dispenser cap.

Rinse Aid Setting

The amount of rinse agent released into the final

wash can be adjusted. The factory setting is at the

midpoint. If there are rings of calcium (hard water)

spots on dishes, try a higher setting. If there is

foaming, use a lower setting.

To adjust the setting:

Remove the dispenser cap;

then turn the adjuster

counterclockwise to

increase the amount

of rinse agent or

clockwise to reduce

the amount of rinse agent dispensed.

Rinse agent

adjuster

■ No prerinsing of normal food soil is required.

■ Scrape off hard soils, bones, toothpicks, skins and

seeds.

■ Remove large quantities of any remaining food.

■ Remove leafy vegetables, meat trimmings and

excessive amounts of grease or oil.

Dish Preparation Prior to Loading

Indicator

window

Dispenser cap

Your dishwasher comes equipped with an automatic liquid

dishwasher detergent dispenser (SmartDispense

) and a

manual dispenser. You can use either of these dispensers

but don’t use both at the same time.

The cover of the manual dispenser will open during the

wash cycle. If you are using SmartDispense

, leave the

cover of the manual dispenser open before starting the

cycle.

For the manual dispenser, Cascade

and Electrasol

Automatic Dishwashing Detergents have been approved.

You may use powder, liquid, gel or tablets in this dispenser. It

is important to keep powdered detergents and tablets fresh

and dry so they don’t lose effectiveness. Therefore, do not

put detergent into the manual dispenser until you are ready

to wash dishes.

Filling Manual Detergent Dispenser

The amount of detergent to use depends on whether your

water is hard or soft. With hard water, you need extra

detergent. With soft water, you need less detergent.

Protect your dishes and dishwasher by contacting your

water department and asking how hard your water is.

Twelve or more grains is extremely hard water. A water

softener is recommended. Without it, lime can build up in

the water valve, which could stick while open and cause

flooding. Too much detergent with soft water can cause a

permanent cloudiness of glassware, called etching.

Use the information in the table below as a guide to

determine the amount of automatic dishwasher detergent

to place in the dispenser. You may use powder, liquid, gel

or tablets in this dispenser.

When using automatic dishwashing detergent tablets,

simply place one tablet in the main wash section and close

the cover.

For heavily soiled loads, use a bit more detergent. For water

temperatures above 140°F, use a bit less detergent.

For heavily soiled loads, use the Pots and Pans or Heavy Wash

cycle.

DO NOT USE HAND DISH DETERGENT

NOTE: Using a detergent that is not specifically designed

for dishwashers will cause the dishwasher to fill with suds.

During operation, these suds will spill out of the dishwasher

vents, covering the kitchen floor and making the floor wet.

Because so many detergent containers look alike, store the

dishwasher detergent in a separate space from all other

cleaners. Show anyone who may use the dishwasher the

correct detergent and where it is stored.

While there will be no lasting damage to the dishwasher,

your dishes will not get clean using a dishwashing

detergent that is not formulated to work with dishwashers.

Consumer Support

Troubleshooting TipsOperating InstructionsSafety Instructions

ge.com

MAIN WASH

PRE

WASH

Soft

Medium

Soft

Medium

Hard

Extremely

Hard

Manual Detergent Dispenser

Detergent Cups to Fill

Fill cup to soft line (1/3 full)

Fill cup to medium soft line (2/3 full)

Fill cup to medium hard line

(completely full)

Fill both main wash cup

and pre wash cup

Number

of Grains

Less than 4

4 to 8

8 to 12

Greater

than 12

SmartDispense

Manual Detergent

Dispenser

This dishwasher may have SmartDispense

, a

feature which automatically dispenses liquid

automatic dishwasher detergent into each cycle

based on soil level and water hardness.

To utilize the SmartDispense

Detergent Dispenser,

it must first be filled. Although any liquid or gel

automatic dishwashing detergent can be used in the

SmartDispense

system, all liquid or gel automatic

dishwashing detergents are not the same. Most

automatic dishwashing detergents are chlorine

bleach-based (such as Cascade

or Electrasol

)

while others contain enzymes (such as Cascade

Complete

Do not mix any chlorine bleach-based automatic

dishwashing detergent with any dishwashing

detergent containing enzymes as this could cause

the detergents to congeal and lead to blockage of

the SmartDispense

system. Check the detergent

label to determine if the detergent is chlorine

bleach-based or one that contains enzymes. It is

recommended that the same type of detergent be

used when refilling your SmartDispense

system.

CAUTION! Absolutely do not add

powder detergent, tablets or any liquid soap or

detergent normally used for washing hands or

dishes in a sink. Only use liquid or gel detergent

specifically designed for use in an automatic

dishwasher.

To open the dispenser for filling, push down and

turn the blue cap counterclockwise until the cap is

loose. Lift cap off.

Set the door at a comfortable angle to fill the

dispenser.

Aim the detergent bottle at the opening in the door

and begin to fill.

The dispenser will hold 45 oz of liquid dishwasher

detergent (standard size bottle).

When full, replace the cap and turn clockwise until

tight to ensure no water enters the SmartDispense

dispenser. If residue is left on the door, it will be

washed off in the next cycle.

An indicator light will turn on to notify you when the

dispenser needs to be filled again. After filling, the light

will not turn off until the door is closed. A full dispenser

will last approximately 1 month for the average user.

NOTE: If you are not using SmartDispense

and you

want to turn the LOW DETERGENT LED light off, press

the ADDED HEAT pad 5 times within 3 seconds. You will

hear 3 beeps; then the light will go off. You can turn the

light back on by pressing the ADDED HEAT pad 5 times

within 3 seconds.

Operating Instructions Safety Instructions

Consumer Support

Troubleshooting Tips

Using the dishwasher.

SmartDispense

Detergent Dispenser (some models)

LOW DETERGENT

SmartDispense

ENSING

ASHING

RYING

ANITIZED

LEAN

Light will

turn on

when

time to

refill

Turn clockwise.

(appearance may vary)

Prior to the first use, the dishwasher needs to

be calibrated for water hardness. Please follow

directions below to calibrate the dishwasher to

the hardness of your tap water.

Determine the Hardness of Your Tap Water

In the bag that contained these instructions, you

should find a water hardness test strip package. Read

the instructions on the package, remove the test strip

and follow the instructions to determine the hardness

level of your tap water. You will use this information to

calibrate your dishwasher to dispense the optimal

amount of detergent.

Water hardness test strip indication

Calibration of 12-Button Front-Control

Models With 3-Digit Display

Close and latch the door (lights on, dishwasher

not running).

Press the COOKWARE and DELAY HOURS pads

at the same time for 3 seconds. The display will

show a number from 1 to 5. This is the water

hardness value currently set.

Press the COOKWARE pad to raise the value or

the NORMAL pad to lower the value. Set the

water hardness value to the number determined

with the test strip and table above.

Once the water hardness is set, press the

START/RESET pad to save the setting and return

the dishwasher to normal operation.

Calibration of 7-Button Front-Control

Models With 3-Digit Display

Open the door and touch a pad (other than

START) to turn lights on.

Press the “Up” Arrow Pad and DELAY

HOURS pad at the same time for 3 seconds. The

display will show a number from 1 to 5. This is the

water hardness value currently set.

Press the “Up” Arrow Pad to raise the value

or the “Down” Arrow Pad to lower the value.

Set the water hardness value to the number

determined with the test strip and table at the left.

Once the water hardness is set, press the

START/RESET pad to save the setting and return

the dishwasher to normal operation.

Calibration of Models Without a 3-Digit Display

Front controls

Close and latch the door (lights on, dishwasher

not running).

Press the COOKWARE and DELAY HOURS pads

together for 3 seconds. All lights will light up and

you will hear 1 to 5 beeps. The number of beeps

indicates the current hardness value.

To change the setting, press the DELAY HOURS

pad the number of times that corresponds to the

water hardness value determined at the left. The

control will beep each time you press the pad.

Once finished pressing the pad, you will hear a

confirmation with beeps for the number of times

you pressed the pad.

If the number of beeps is not what you desire,

start pressing the DELAY HOURS pad again to

reenter a new water hardness level.

Once the water hardness is set, press the

START/RESET pad to save the setting and return

the dishwasher to normal operation.

Top controls

Open the door and touch a pad to turn lights on.

Press the “Up” Arrow Pad and DELAY

HOURS pad at the same time for 3 seconds. All

lights will light up and you will hear 1 to 5 beeps.

The number of beeps indicates the current

hardness value.

To change the setting, press the DELAY HOURS

pad the number of times that corresponds to the

water hardness value determined at the left. The

control will beep each time you press the pad.

Once finished pressing the pad, you will hear a

confirmation with beeps for the number of times

you pressed the pad.

If the number of beeps is not what you desire,

start pressing the DELAY HOURS pad again to

reenter a new water hardness level.

Once the water hardness is set, press the

START/RESET pad to save the setting and return

the dishwasher to normal operation.

NOTE: You should recalibrate the dishwasher control

if water conditions change; for example, if a water

softener system is added or removed from your

home.

Consumer Support

Troubleshooting TipsOperating InstructionsSafety Instructions

ge.com

SmartDispense

Detergent Dispenser

Water Hardness Calibration

0 RED

1 RED

2 RED

3 RED

4 RED

SOFT

HARD

Value to Enter

into Dishwasher

Press at the same time.

Display

LOW DETERGENT

Smart Dispense

ENSING

ASHING

RYING

ANITIZED

LEAN

RINSE ONLY

SINGLE RACK WASH

PLASTIC CYCLE

CHINA CYCLE

SPEED CYCLE

NORMAL

OOKWARE

NTI-

ACTERIAL

Press at the same time.

Display

Operating Instructions Safety Instructions

Consumer Support

Troubleshooting Tips

Loading the dishwasher racks.

For best dishwashing results, follow these loading guidelines. Features and appearance of racks and silverware

baskets may vary from your model.

Upper Rack

Although the upper rack is primarily for

glasses, cups and saucers, pots and pans can

be placed in this rack for effective cleaning.

Cups and glasses fit best along the sides. This

is also a secure place for dishwasher plastics.

The utility shelf (some models) may be placed

in the up or down position to add flexibility. A

wine glass holder (some models) secures wine

glasses for best washability.

Some models have contoured metal cup

shelves that can secure up to 12 wine glasses

(as shown).

Because wine glasses come in various sizes,

after loading, slowly push in the rack to make

sure they will clear the top of the dishwasher.

Some models have an Angled Rack System,

which allows you to angle your dishes, such

as coffee mugs, for better cleaning and

quicker drying. To position the tines, pull the

lever forward then drop the tines into

position, then release the lever.

The upper rack is good for all kinds of

odd-shaped utensils. Saucepans, mixing

bowls and other items should be placed face

down. Fold-down tines (on some models)

provide flexibility for extra-large and hard-

to-fit items.

Secure larger dishwasher-safe plastics over

2 tines when possible.

Make sure small plastic items are secure so

they can’t fall onto the heater.

Be sure that items do not protrude through

the bottom of the rack and block rotation of

the middle spray arm. This could result in

poor wash performance for items in the

upper rack.

Check to make sure that no items will block

rotation of the wash arm.

NOTE:

The Single Rack Wash selection, on

models with this feature, washes the upper

rack only. If you use this feature, do not load

items in the lower rack.

Adjustable Upper Rack

The standard position of your adjustable rack

is “up” which allows for maximum clearance

for your taller items in the lower rack. If you

have taller wine glasses, tumblers or other

items to place in the upper rack, you may

want to adjust the rack to the lower position.

To lower the rack, support the weight of the

rack with your hands as shown and press

both finger pads about 1/4″ toward the inside

of the rack as indicated and guide the rack

down to its lower position.

To raise the rack to the “up” position, pull up

on the center of the rack side frame until the

rack locks into place.

Consumer Support

Troubleshooting TipsOperating InstructionsSafety Instructions

Remove end cap

Press thumb

tab out

ge.com

Lower Rack

The lower rack is best used for plates, saucers

and cookware. Large items such as broiler

pans and baking racks should go along the

left-hand side. Load platters, pots and bowls

along the sides, in corners or in the back. The

soiled side of items should face the center of

the rack. If necessary, oversized glasses and

mugs can be placed in the lower rack to

maximize loading flexibility.

Also, be careful not to let a portion of an item

such as a pot or dish handle extend through

the bottom rack. This could block the wash

arm and cause poor washing results.

Fold-down tines (on some models) provide

flexibility for extra-large and hard-to-fit items.

The tines may be left in the up position or

folded down to customize the lower rack.

Removing the Upper Rack

You can remove the upper rack to allow

space for large items in the lower rack.

NOTE: Do not use the SINGLE RACK WASH

cycle (some models) with this feature. Single

Rack Wash cycle is for upper rack wash only.

The recommended cycle for lower rack only

use is the COOKWARE cycle.

To remove the upper rack:

Press thumb tab out and remove the

front end caps on each side of the rail.

Pull the rack straight out and off the rails.

Replace the end caps.

Push the rails all the way back into the

dishwasher.

Slide the shower nozzle attachment

(located in the bag that contained these

instructions) over the spout.

Then fill the lower rack and begin

your cycle.

NOTE: Don’t forget to remove the shower

nozzle attachment before you replace the

upper rack.

Shower nozzle

attachment

Don’t let any

item extend

through bottom.

To remove end baskets, grasp the

basket at opposite corners and

slide apart.

Three-piece basket (on some models)

One-piece basket (on some models)

Silverware Basket

To load flatware, simply push the adjustable

handle to either side (on some models). Put

flatware in the removable basket with fork

and knife handles up to protect your hands.

Place spoons in the basket with handles

down. Mix knives, forks and spoons so they

don’t nest together. Distribute evenly. Small

plastic items, such as measuring spoons and

lids from small containers should go in the

bottom of the silverware basket with the

silverware on top.

The one-piece silverware basket (on some

models) can be placed in the front, right side

or back of the lower rack.

A variety of options is available regarding

the three-piece silverware basket (on some

models) in your dishwasher. The complete

basket is designed to fit on the right side of

the lower rack. Additionally, each end of

the basket is removable to add loading

flexibility to accommodate flatware and

lower rack capacity needs.

The lids of both end and middle baskets (on

some models) can be closed to contain small

items. Long items can be placed on the utility

shelf in the upper rack.

Operating Instructions Safety Instructions

Consumer Support

Troubleshooting Tips

Loading the dishwasher racks.

Extra Rack Features (on some models)

Cutlery Tray

The cutlery tray holds up to 4 large knifes

such as a carver, chef’s knives, bread knife,

etc., that are too tall to fit in the silverware

basket.

Hook the tray onto the rear of the upper rack.

Lay the knives between the guides

(as shown).

Bowl Tines

The special large-bowl tines in the lower rack

add flexibility to your loading pattern. They

are useful for serving bowls or other large

bowls.

To use the bowl tines, fold down the

2 rows of flex tines in front of the bowl

tines and load bowls just as you would

in the upper rack.

Loading place settings…

Follow these guidelines for loading 10 place settings. Features and appearance of racks and silverware baskets may

vary from your model.

NOTE:

Silverware should be individually loaded into the slots on the silverware basket lid.

Upper Rack—10 place settings Lower Rack—10 place settings

Follow these guidelines for loading 12 place settings. Features and appearance of racks and silverware baskets may

vary from your model. NOTE: Silverware should be individually loaded into the slots on the silverware basket lid.

Upper Rack—12 place settings Lower Rack—12 place settings

These tines fold down

Large-bowl tines

Consumer Support

Troubleshooting TipsOperating InstructionsSafety Instructions

Caring for the dishwasher. ge.com

Cleaning the Exterior Door Panel

Before cleaning the front panel, make

sure you know what type of panel you have.

Refer to the last two letters of your model

number. You can locate your model number

on the left-hand tub wall just inside the door.

If your model number ends with BB, CC, WW,

SA or BG, then you have a Painted Door

panel. If your model number ends with SS,

then you have a Stainless Steel Door panel. If

your model number ends with CS, then you

have a CleanSteel panel.

Follow the instructions below for cleaning the

door panel for your specific model.

Painted Door Panel (model numbers ending

in BB–black, CC–bisque, WW–White, SA–silver

metallic or BG–graphite black)

Use a clean, soft, lightly dampened cloth,

then dry thoroughly. You may also use a

good appliance wax or polish.

Stainless Steel Door Panel (model numbers

ending in SS)

The stainless steel panels can be cleaned

with Stainless Steel Magic or a similar product

using a clean, soft cloth. Do not use appliance

wax, polish, bleach or products containing

chlorine on Stainless Steel doors.

You can order Stainless Steel Magic

#WX10X15 through GE Parts by calling

800.626.2002.

CleanSteel Door Panel (model numbers

ending in CS)

Use a clean, soft, lightly dampened cloth,

then dry thoroughly. Do not use appliance

wax, polish or any chemical agent on

CleanSteel doors.

Do not wipe the dishwasher with a soiled

dish cloth or wet towel. These may leave

a residue. Do not use scouring pads or

powdered cleaners because these products

can scratch the finish.

Cleaning the Control Panel

To clean the control panel, use a lightly

dampened cloth. Then dry thoroughly.

Check the air gap any time

your dishwasher isn’t draining

well.

An air gap protects your dishwasher

against water backing up into it if a drain

clogs. The air gap is not a part of the

dishwasher. It is not covered by your

warranty. Not all plumbing codes require

air gaps, so you may not have one.

The air gap is easy to clean.

Turn off the dishwasher and lift off the

cover.

Remove the plastic cap and clean with

a toothpick.

Air gap

Does Your Dishwasher Have an Air Gap?

Stainless Steel Interior—Tub and Inner Door

The stainless steel used to make the

dishwasher tub and inner door provides

the highest reliability available in a GE

dishwasher. If the dishwasher tub or inner

door should be scratched or dented during

normal use, they will not rust or corrode.

These surface blemishes will not affect

their function or durability.

If your dishwasher is left in an unheated

place during the winter, ask a service

technician to:

Cut off electrical power to the

dishwasher. Remove fuses or trip

circuit breaker.

Turn off the water supply and disconnect

the water inlet line from the water valve.

Drain water from the water inlet line

and water valve. (Use a pan to catch

the water.)

Reconnect the water inlet line to the

water valve.

Protect Against Freezing

Operating Instructions Safety Instructions

Consumer Support

Troubleshooting Tips

Problem Possible Causes What To Do

Dishes and flatware Low inlet water temperature • Make sure inlet water temperature is correct (see page 8). Turn on the hot

not clean water faucet nearest the dishwasher; let run until the water temperature

stops rising. Then start the dishwasher and turn off the faucet. This ensures

the entering water is hot.

• Try not to use the dishwasher when hot water is being used elsewhere

in the house; for example, when doing laundry or when a family member

is using the shower.

Water pressure is temporarily low • Turn on a faucet. Is water coming out more slowly than usual? If so, wait

until pressure is normal before using your dishwasher.

• Try not to use the dishwasher when hot water is being used elsewhere

in the house; for example, when doing laundry or when a family member

is using the shower.

Air gap or disposer is clogged • Clean the air gap or flush the disposer.

Improper rack loading • Make sure large dishware does not block the detergent dispenser or the

wash arms. See the Loading the dishwasher racks section.

No air gap or high drain loop • Verify that you have an air gap or a high drain loop. Refer to the

Installation Instructions.

Error Messages Possible Causes What To Do

START/RESET status You have pressed the • Press the START/RESET pad only one time to start the dishwasher. When the

indicator light flashing START/RESET pad while the dishwasher is running, only press the START/RESET pad if you wish to cancel

dishwasher is running. This will (reset) the cycle.

cancel the cycle. The light will

stop flashing after the dishwasher

drains (about 90 seconds).

Power to the dishwasher was • The light will stop flashing after the dishwasher drains out the water. A new

turned off while a cycle was cycle will start automatically when the drain ends.

running and power has just been

restored to the dishwasher. The

blinking lights indicate that the

dishwasher is draining water

inside.

Dishwasher BEEPS This is a reminder that your • Close and latch the door after opening it mid-cycle. Beeping will stop and

once every 30 seconds dishwasher door has been left dishwasher will complete cycle.

open during operation. It will

continue beeping until you close

the door.

Beeping at the end This is normal. The dishwasher • To turn off the double beep indicator (or re-activate it if it was previously

of the cycle will beep twice at the end of turned off), press the HEATED DRY pad 5 times within 3 seconds. A triple

the cycle. beep will sound to indicate the end-of-cycle beep option has been turned

on or off.

Low Detergent SmartDispense

has less than • Fill the SmartDispense

reservoir with liquid dishwasher detergent. After

Light ON 10 cycles worth of detergent filling the reservoir, the LOW DETERGENT light will turn OFF once the

left in the dishwasher. door is closed.

Before you call for service…

Troubleshooting Tips

Save time and money! Review the charts on the following

pages, or visit ge.com. You may not need to call for service.

Problem Possible Causes What To Do

Spots and filming • Use Jet-Dry

or Cascade Crystal Clear

rinse agents to remove spots and

on glasses and prevent new film buildup.

flatware

• Make sure water temperature is at least 120°F.

• Load dishwasher as shown in the Loading Place Settings section.

• Make sure detergent is fresh.

• If water is extremely hard, a softener may be required.

Cloudiness on Combination of soft water and • This is called etching and is permanent. To prevent this from happening,

glassware too much detergent use less detergent if you have soft water. Wash glassware in the shortest

cycle that will get them clean. Recalibrate the SmartDispense

system if

you are using it. See pages 9 and 11.

Water temperature entering • This could be etching. Lower the water heater temperature.

the dishwasher exceeds 150°F

Suds in the tub Correct detergent • Use only automatic dishwasher detergents to avoid sudsing.

wasn’t used Cascade

and Electrasol

Automatic Dishwashing Detergents

have been approved for use in all GE dishwashers.

• To remove suds from the tub, open the dishwasher and let

suds dissipate. Close and latch the dishwasher door. Pump out water

by touching the START/RESET pad once; then 30 seconds later,

touch the START/RESET pad again. Repeat if necessary.

Rinse agent was spilled • Always wipe up rinse agent spills immediately.

Detergent left in Dishes are blocking the • Reposition the dishes, so the water from the lower spray arm can

dispenser cups detergent cup or flush the detergent cup or outlet from the SmartDispense

system.

or on door SmartDispense

outlet See pages 13 and 14.

Water in the Cap not tightened after filling • Use a turkey baster to remove as much water as possible from the

SmartDispense

™

the dispenser SmartDispense

™

dispenser and refill it as normal. Be sure to tighten the

dispenser cap fully to prevent water from entering the dispenser.

Black or gray Aluminum utensils have • Remove marks with a mild, abrasive cleaner.

marks on dishes rubbed against dishes

Dishes don’t dry Low inlet water temperature • Make sure inlet water temperature is at least 120°F.

• Select HEATED DRY.

• Use PRE WASH or ADDED HEAT options.

• Select a higher cycle, such as ANTI-BACTERIA or COOKWARE.

Rinse agent dispenser is empty • Check the rinse agent dispenser and fill as required.

Control panel responded Door latch may not be properly • Make sure the door is firmly closed.

to inputs but dishwasher seated

never filled with water

Water valve may be turned off • Make sure water valve (usually located under the sink) is turned on.

Stained tub interior Some tomato-based foods can • Use of the RINSE ONLY cycle after adding the dish to the load

cause reddish stains can decrease the level of staining. GE recommends Cascade

Plastic Booster to help remove these types of stains.

Tea or coffee stains • Remove the stain by hand, using a solution of 1/2 cup bleach

and 3 cups warm water.

WARNING

Before cleaning interior, wait at least 20 minutes after a cycle for the

heating elements to cool down. Failure to do so can result in burns.

An overall yellow or brown film can • A special filter in the water supply line is the only way to correct

be caused by iron deposits in water this problem. Contact a water softener company.

White film on inside surface— • GE recommends Jet-Dry

or Cascade Crystal Clear

to help

hard water minerals prevent hard water mineral deposits from forming.

• Run dishwasher with citric acid to remove mineral deposits. Citric

acid (Part number: WD35X151) can be ordered through GE Parts.

See back cover for ordering information.

Extremely hard water

Low inlet water temperature

Overloading the dishwasher

Improper loading

Old or damp powder detergent

Rinse agent dispenser empty

Too little detergent

Consumer Support

Troubleshooting TipsOperating InstructionsSafety Instructions

ge.com

Operating Instructions Safety Instructions

Consumer Support

Troubleshooting Tips

Before you call for service…

Problem Possible Causes What To Do

Dishwasher won’t run Fuse is blown or circuit breaker • Replace fuse or reset circuit breaker. Remove any other appliances from

is tripped the circuit.

Power is turned off • In some installations, the power to the dishwasher is provided through a

wall switch, often located next to the disposer switch. Make sure it is on.

Control panel is locked • Unlock control panel. See page 6.

Control panel needs to be • Turn off power to the dishwasher (circuit breaker or wall switch) for

rebooted 30 seconds; then turn back on.

Control panel lights Time too long between • Each pad must be touched within 5 minutes of the others.

go off when you’re touching of selected pads To relight, touch any pad again, or unlock and relatch door.

setting controls

Water standing in This is normal • A small amount of clean water around the outlet on the tub

the bottom of the tub bottom at the back of the tub keeps the pump seal lubricated.

Water won’t pump Drain is clogged • If you have an air gap, clean it. See page 15.

out of the tub

• If the dishwasher drains into a disposer, run disposer clear.

• Check to see if your kitchen sink is draining well. If not, you

may need a plumber.

Steam This is normal • Warm, moist air comes through the vent by the door latch during drying

and when water is being pumped out. This is necessary for drying.

Sanitized light does The door was opened and the • Do not interrupt the cycle anytime during or after main wash.

not illuminate at the cycle was interrupted during

end of the cycle or after the main wash portion

(Anti-Bacteria

The incoming water • Raise the water heater temperature to between 120°F and 140°F.

cycle only)

temperature was too low

Noise Normal operating sounds • These are all normal. No action is required.

Detergent cup opening

Water entering dishwasher

The motor stops and starts at

various times during the cycle

Drain pump sounds during

pump out

Drying fan running for 2–4 hours

after CLEAN light is illuminated

(Top Control Panel models only)

Rattling dishes when the spray • Make sure dishes are properly loaded. See the Loading the

arm rotates dishwasher racks section.

Troubleshooting Tips

General Electric Company

Warranty Registration Department

P.O. Box 32150

Louisville, KY 40232-2150

GE Service Protection Plus

™

GE, a name recognized worldwide for quality and dependability, offers you

Service Protection Plus

™

—comprehensive protection on all your appliances—

No Matter What Brand!

Benefits Include:

• Backed by GE

• All brands covered

• Unlimited service calls

• All parts and labor costs included

• No out-of-pocket expenses

• No hidden deductibles

• One 800 number to call

You will be completely satisfied with our service protection or you may request your money back

on the remaining value of your contract. No questions asked. It’s that simple.

Protect your refrigerator, dishwasher, washer and dryer, range, TV, VCR and much more—any brand!

Plus there’s no extra charge for emergency service and low monthly financing is available. Even icemaker

coverage and food spoilage protection is offered. You can rest easy, knowing that all your valuable household

products are protected against expensive repairs.

Place your confidence in GE and call us for more information in the U.S.

toll-free at 800.626.2224 and in Canada, toll-free at 888.261.2133.

*All brands covered, up to 20 years old, in the continental U.S.

We’ll Cover Any

Appliance. Anywhere.

Anytime.*

Please place in envelope and mail to:

✁

Cut here

Consumer Product Ownership Registration

rta

GE Consumer & Industrial

Appliances

General Electric Company

Louisville, KY 40225

ge.com

First

Name

Mr. ■■ Ms. ■■ Mrs. ■■ Miss ■■

Street

Address

City

State

Date Placed

In Use

Month

Day

Year

Zip

Code

Apt. #

Last

Name

Phone

Number

Consumer Product Ownership Registration

Dear Customer:

Thank you for purchasing our product and thank you for placing your confidence in us.

We are proud to have you as a customer!

Follow these three steps to protect your new appliance investment:

Important: If you did not get a registration card with your product, detach

and return the form below to ensure that your product is registered,

or register online at ge.com. Canadian consumers, please use the

mail-in card on page 19 in the French Language section.

Model Number Serial Number

✁

Cut here

Complete and mail

your Consumer

Product Ownership

Registration today.

Have the peace of

mind of knowing we

can contact you in

the unlikely event of

safety modification.

After mailing the

registration below, store

this document in a safe

place. It contains

information you will need

should you require

service. Our service

number is 800.GE.CARES

(800.432.2737) in the U.S.

and 800.361.3400

in Canada.

Read your Owner’s

Manual carefully.

It will help you

operate your new

appliance properly.

Model Number Serial Number

E-mail Address*

* Please provide your e-mail address to receive, via e-mail, discounts, special offers and other important

communications from GE Appliances (GEA).

■■ Check here if you do not want to receive communications from GEA’s carefully selected partners.

FAILURE TO COMPLETE AND RETURN THIS CARD DOES NOT DIMINISH YOUR

WARRANTY RIGHTS.

For information about GEA’s privacy and data usage policy, go to ge.com and click on “Privacy Policy”

or call 800.626.2224.

La page est en cours de chargement...

GE PDW8800JBB Manuel utilisateur

Marque: GE

Modèle: PDW8800JBB

Catégorie: Lave-vaisselle

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: GE PDW8800JBB User manual

GE PDW8800JBB Manuel utilisateur

GE PDW8800JBB Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents