H Koenig AXO940 Manuel utilisateur

axo940

Vacuum cleaner

Aspirateur

Staubsauger

stofzuiger

aspiradora

aspiratore

ENGLISH

1. Be sure to use the cleaner in compliance with the

contents of this manual, and use the fittings designated

by the manufacturer.

2. Please do not leave the cleaner when it is powered on.

Turn off the power switch and pull out the power plug

when not using or before maintenance.

3. Please do not pull or carry the cleaner by the power cord,

or nip it when closing a door; keep the cord free from the

press of the cleaner.

4. Please do not let children take the cleaner as a toy, and

close attention is necessary when the cleaner

approaches children.

5. Please do not use the cleaner when its power cord or plug

is damaged. Send it to the appointed service center.

Please do not unplug by pulling the cord or plug. To

unplug, grasp the plug, not the cord.

6. Never pull the power plug or use the cleaner with wet

hands.

7. When using the cleaner, pay attention to prevent any hair

roll or other rubbish block up the air inlet (including the

hose and the spile), otherwise motor failure and housing

Safety Warning

distortion may be caused. If the matters absorbed in

forms a blockage, stop the cleaner by pulling out the

power plug immediately to clean the blockage.

8. When using the cleaner, don’t plug up the air outlet by

towel or other matters, otherwise the efficiency of dust

absorbance will be influenced, and the motor will be at

high risk of being burnt out.

9. Never use the cleaner at uneven floor or ground; and be

very careful when cleaning stairs to prevent the cleaner

from falling down.

10. Never absorb live stumps with the cleaner, otherwise

the motor may be damaged.

11. The cleaner should be kept far away from heat sources

(such as central heating, oven, etc) to avoid the distortion

of plastic parts as well as the influence caused by such

distortion.

12. Before using the cleaner, please remove big and sharp

matters on the floor to avoid damaging the plastic parts,

filter gauzes and motor.

13. Never absorb water or other liquid with this cleaner,

otherwise, the motor will be damaged.

14. This device is not intended for use by persons with

reduced capacity on the physical, mental or sensory or

lack of experience and knowledge (including children),

unless he has them was asked to monitor or if they have

had instructions on the use of the appliance by a person

responsible for their safety. Children should be

supervised to ensure they do not play with the device.

15. If the power cord is damaged, it must be replaced with

an after-sales service to avoid any danger.

16. Do not operate this appliance if it has a damaged cord

or plug, if it is not working properly or if it has been damaged

or dropped. If the supply cord is damaged, it must be

replaced by the manufacturer or its service agent or a

similarly qualified person in order to avoid a hazard.

17. This appliance may be used by children of at least

8 years of age, as long as they are supervised and

have been given instructions about using the

appliance safely and are fully aware of the dangers

involved.

18. Cleaning and maintenance should not be carried

out by children unless they are at least 8 years of age and

are supervised by an adult.

19. Keep the appliance and its power cord out of

reach of children under 8 years of age.

20. When using electrical equipment, safety precautions

must always be taken to prevent the risk of fire,

electric shock and/or injury in the event of misuse.

21. Make sure that the voltage rating on the

typeplate corresponds to your main voltage of your

installation. If this is not the case, contact the dealer and

do not connect the unit

22. Never leave the unit unattended while in operation.

23. Make sure that the voltage rating on the typeplate

corresponds to your main voltage of your installation. If

this is not the case, contact the dealer and do not

connect the unit.

24. Please keep this document at hand and give it to the

future owner in case of transfer of your device.

25. The device must not be used if it has been dropped,

it obvious signs of damage are visible or if it has leaks.

26. The device is not intended to be operated by external

timer means or a remote control system.

1. Power plug

2. Cord reeling pedal

3. Cyclone dust barrel

4. Hose

5. Accessory Bracket

6. Handle

7. Air Escape Push button

8. Metal extension pipe

9. Switch Pedal

10. Air outlet grid

11. Ordinary floor brush

Names of Parts and Components

1

2

3

4

5

6

7

8

9

10

11

1. Before assembling the cleaner, please confirm all parts and components for the cleaner are

received by referring to Parts and Components List.

2. Please remember to cut off the power supply before assembly.

Assembly of hose

1. As is shown in Figure (3), insert the hose into the duct inlet of the machine body in horizontal

direction. Please pay attention to the alignment of two projecting parts. Turn the hose right when

it is pushed into the bottom, a click of inserting sound may be heard, i.e. the hose is assembled

into the machine body completely.

2. Assembly and Removal of dust barrel

As is shown in Figure (4), place the bottom of the dust barrel on the projecting part at the front end

of the machine body, and press down the dust barrel. When the front-end hook is entered into the

corresponding part of the machine body completely, and a click of inserting sound is heard, which

indicate that the dust barrel is assembled in place. To remove the dust barrel, press down the

handle of the dust barrel; when the handle is pressed down to the bottom, the dust barrel can be

lifted to remove.

Assembly Instructions

Figure (3)

Assembly of metal extension pipe and floor brush

Insert the front end of the hose handle into the metal extension pipe according to Figure (5); then

insert the other end of the metal extension pipe into the rounded inlet of the floor brush, and adjust

to the proper direction. At this time, the assembly of the whole machine is completed.

How to start

1. First of all, pull out the power cord from the cord reel to the needed length; insert the power

cord plug into the power socket, and press down the power switch button with finger or step

on it with foot; then you can control the start and stop of the cleaner.

2. The yellow mark on the power cord indicates its desired length. Never pull out the power

cord to the length exceeding the red mark.

Protective devices of motor

1. There is a temperature controller designed in the body of cleaner motor, which can automatically

cut off the power supply of motor to prevent overheating. When the air-inlet or air-outlet pipe is

overloaded or blocked, the temperature of motor rises, then the temperature controller cuts off the

power supply of motor automatically to make the motor cool, preventing the cleaner from being

damaged.

2. If the temperature controller is cut off, stop the cleaner immediately and pull out the power plug

to make the cleaner cool, and check and remove the hair roll or other roll-like rubbish blocking the

air inlet (including the hose and the spile), and replace the filter HEPA or filter gauze when necessary.

3. After cooling the motor for 30mins, plug in the power plug and check whether the temperature

controller has been reset. If the power supply of the cleaner hasn’t been cut off, the temperature

controller of the motor won’t be reset even when the motor has become cool.

Operation Instructions

Figure (4)

Figure (5)

1. All the day-to-day maintenance and repair jobs should

be done after the power plug has been pulled out.

2. Frequently remove the rubbish from the dust barrel, so

as to avoid the failure of the cleaner.

3. Never wipe the surface of the cleaner with gasoline or

oily liquid. Wipe it with water or neutral detergent. Caution:

be sure to wring out the wiping cloth dry for wiping, it is

prohibited for water to infiltrate into electrical elements of

the cleaner.

4.When the cleaner is placed idle not in use, it should not

be put directly in the sun or in a damp place.

1. Upon the completion of the operation of the cleaner, turn off its power supply, and pull the

power plug out of the power socket, then step on the cord reeling button to reel in the power

cord fully. Hang the floor brush onto the floor brush hook, as is shown in Figure (6).

Maintenance of the Cleaner

Storage of the Cleaner

Figure (6)

2. Place the cleaner in the dry indoor environment.

Remove the rubbish in the dust barrel frequently to avoid the failure of the cleaner.

1. Clean the dust barrel only after the power plug of the cleaner has been pulled out;

2. Put the dust barrel over the rubbish bin (bag), press down the releasing button of the dust barrel,

the bottom cover of the dust barrel will automatically fall down, and clear and empty the dust

barrel, as is shown in Figure (7).

Cleaning of front filter for motor:

Warning: please make sure the power supply of the cleaner

has been cut off before carrying out the following steps:

1. Pull out the power cord plug of the cleaner from the

power socket.

2. Press down the handle of the dust barrel to remove the

dust barrel, and remove the cover of the front filter for

motor, and then use the brush to clean the filter (sponge

and filter gauze with composite coating) or place it under

the cock to clean, as is shown in Figure (8/9).

Cleaning of the Dust Barrel

Figure (7)

Figure (8) Figure (9)

Caution:

It is normal that the white central filter in the dust barrel may

change color, which cannot affect its filtration performance.

If the hose and the central filter are difficult to clean, we

recommend that you use water to flush them; however,

please be sure to place them in the dry air for at least 24

hours after they are flushed by water.

Key Points:

Please note: when the dust collecting barrel or the filter

cover is not installed in place, the operation status will be

invalid, and the cleaner will have no dust absorption

capacity. At this time, you need to check carefully whether

the dust collecting barrel and the filter cover have been

installed in place.

Caution: please keep the suction passage unobstructed,

otherwise the motor may become overheating or even be

damaged.

Replacement of rear filter for motor

The rear filter for motor is installed behind the air outlet grid,

which can be washed due to the materials used. When the

surface is jammed seriously by dust, the filter should be

replaced by a new one or washed by water to maintain

enough suction force. (Figure 10/11)

Figure (10) Figure (11)

It is usually necessary to clean and replace the filters for

motor only after they have been used for 6 months to 12

months. Please remember to confirm that all filters have

been correctly installed into the machine before turning on

the cleaner to use.

Key Points:

The power supply of the cleaner must be cut off before

replacing any filter!

Faults and repair

In case of abnormality with this product, please treat it in the way as stated hereinafter; if the cleaner

still refuses to work normally, please contact the stop from where this product was bought or with

the appointed service point.

Fault

Treatment

The cleaner

cannot operate.

1. Check whether the power plug is inserted securely; pull

out the plug and then reinsert it in the power socket;

2. Check whether the power socket is electrified;

3. Check whether the switch of the cleaner is in “ON”

position.

The suction force

is reduced.

1. Check whether the floor brush, the hose and the spile are

jammed, and remove any blockage immediately;

2. Check whether the air-inlet filter gauze is dusty; frequently

clean rubbish or replace air-inlet and air-outlet HEPA;

There is abnormal

sound when the

motor is under

operation.

1. Stop the cleaner immediately;

2. Check whether the floor brush, the hose and the spile are

jammed, and remove any blockage immediately.

After-sale service

When abnormalities or problems are found with the product in use, please contact the appointed

service point for consultation or repair.

ENVIRONMENT

CAUTION :

Do not dispose of this product as it has with other household products. There is a

separation of this waste product into communities, you will need to inform your local

authorities about the places where you can return this product. In fact, electrical and

electronic products contain hazardous substances that have harmful effects on the

environment or human health and should be recycled. The symbol here indicates that electrical

and electronic equipment should be chosen carefully, a wheeled waste container is marked with

a cross.

Adeva SAS / H.Koenig Europe - 8 rue Marc Seguin, 77290 Mitry-Mory, France

www.hkoenig.com - https://en.hkoenig.com - Tél: +33 1 64 67 00 05

FRANÇAIS

• Vérifiez que tous les accessoires fournis correspondent à

ce qui est décrit dans ce manuel.

• Ne laissez pas l´aspirateur allumé sans surveillance.

Débranchez l´appareil et rembobinez le câble avant de

ranger l´appareil.

• Ne pas tirer ou transporter l´appareil par le câble

d´alimentation. Évitez de pincer le câble dans les portes.

Assurez-vous de ne pas pincer le câble d´alimentation

dans les portes et ne marchez pas sur le câble

• Ne pas laisser les enfants jouer avec l´appareil et soyez

prudent lorsque vous utilisez l´appareil près d’enfants.

• Ne pas utiliser l´appareil avec un câble d´alimentation

endommagé. Faites-le réparer par un professionnel.

Débranchez toujours l´appareil en tirant sur la prise,

jamais sur le câble.

• Ne jamais manipuler le câble ou l´appareil avec des mains

humides.

• Lorsque vous utilisez l´appareil, évitez d´obstruer la

brosse avec des cheveux ou des débris, ceci pourrait

endommager le moteur. Si la brosse est obstruée, arrêtez

l´appareil immédiatement et libérez le conduit.

INSTRUCTIONS DE SÉCURITÉ

• Lorsque vous utilisez l´appareil, n´obstruez pas la brosse,

ceci pourrait surchauffer le moteur.

• Ne pas utilisez sur des surfaces inégales. Soyez prudent

lorsque vous utilisez l´appareil, afin que l´appareil ne

tombe pas.

• Ne pas aspirer des résidus organiques afin que ceci

n´endommage pas l´appareil.

• Maintenez l´appareil éloigne de sources de chaleur

(chauffage, four, etc.) afin d´éviter que les parties

plastiques ne se déforment.

• Avant d´utiliser l´appareil, éliminez les résidus coupants

ou trop grands pour éviter d´endommager l´appareil.

• Ne jamais aspirer d´eau ou tout autre liquide.

• Cet appareil n'est pas destiné à être utilisé par des

personnes présentant des capacités réduites sur le plan

physique, mental ou sensoriel ou bien manquant

d'expérience ou de connaissance, (y compris les

enfants), sauf s'il leur a été demandé de surveiller ou si

elles ont eu des instructions concernant l'utilisation de

l'appareil par une personne responsable de leur sécurité.

Les enfants doivent être surveillés pour s'assurer qu'ils

ne jouent pas avec l'appareil.

• Si le cordon d'alimentation est endommagé, il doit être

remplacé auprès d'un Service après-vente afin d'éviter

tout danger.

• N’utilisez pas l’appareil si son câble d’alimentation ou sa

prise est endommagée, s’il ne fonctionne pas

correctement, s’il a été abimé ou s’il est tombé.

Si le câble d’alimentation est endommagé, il doit être

remplacé par le fabricant ou son agent ou encore par une

personne qualifiée afin d’éviter tout risque.

• Cet appareil peut être utilisé par des enfants âgés d’au

moins 8 ans, à condition qu’ils bénéficient d’une

surveillance ou qu’ils aient reçu des instructions

quant à l’utilisation de l’appareil en toute sécurité et

qu’ils comprennent bien les dangers encourus.

• Le nettoyage et l’entretien par l’utilisateur ne doivent pas

être effectués par des enfants, à moins qu’ils ne soient

• âgés de plus de 8ans et qu’ils soient sous la surveillance

d’un adulte.

• Conserver l’appareil et son câble hors de portée des

enfants âgés de moins 8ans.

• Lors de l’utilisation d’appareils électriques, des

précautions de sécurité doivent toujours être prises

pour prévenir tout risque d’incendie, de choc électrique

et/ou de blessure en cas de mauvaise utilisation.

• Vérifier que le voltage indiqué sur la plaque signalétique

de l’appareil correspond bien à celui de votre

installation électrique. Si ce n’est pas le cas,

adressez-vous au revendeur et ne branchez pas l’appareil

• Ne jamais laisser l’appareil sans surveillance lorsqu’il est

en fonctionnement.

• Vérifier que le voltage indiqué sur la plaque signalétique de

l’appareil correspond bien à celui de votre installation

électrique. Si ce n’est pas le cas, adressez-vous au

revendeur et ne branchez pas l’appareil.

• Veuillez conserver ce document à disposition et le remettre

au futur propriétaire en cas de cession de votre appareil.

• L'appareil ne doit pas être utilisé s'il est tombé, s'il

présente des signes évidents de dommages ou s'il

présente des fuites.

• L'appareil n’est pas destiné à être actionnés par des

moyens de minuterie externe ou un système de

télécommande.

1. Câble d´alimentation

2. Pédale de rembobinage

3. Réservoir d´air Cyclone

4. Embout

5. Crochet

6. Poignée

7. Entrée d´air

8. Tuyau métallique extensible

9. Pédale ON/OFF

10. Grille d´expulsion d´air

11. Brosse pour sols durs

COMPOSANTS

1

2

3

4

5

6

7

8

9

10

11

1. Avant d´assembler l´appareil, assurez-vous d´avoir tous les composants.

2. Ne pas monter avec le câble branché.

3. Comme sur l´Image (3), branchez le tuyau sans forcer. Tournez le tuyau vers la droite jusqu´à

entendre le click.

4. Assembler et retirer le réservoir cyclone.

Comme sur l´image (4), placez le bas du réservoir sur le devant de l´appareil et pressez pour fixer

le réservoir jusqu´à ce que vous entendiez un click. Pour démonter le réservoir pressez la poignée

du réservoir pour le libérer.

Assemblage du tuyau métallique extensible et de la brosse.

Insérez le tube métallique dans l´embout avec la poignée comme sur l´Image (5); puis insérez l´autre

embout dans la brosse en la fixant dans le sens adéquat. Ceci conclut l´assemblage.

Instructions de Montage

Image (3)

Image (4)

Tout d´abord :

1. Tirez sur le câble pour le dérouler et le brancher à la prise. Appuyez sur la pedla pour allumer

l´appareil.

2. La marque jaune vous indique à quel point vous arrêter pour éviter de trop tirer sur le câble.

Essayer de ne pas tirer le câble jusqu´à la marque rouge.

Protection du moteur

1. Un dispositif de control de température est incorporé dans le moteur afin de le protéger d´une

surchauffe en coupant le moteur quand le température augmente.

Si le tuyau est bouché, ceci augmente la température et le dispositif de control coupe le moteur

pour éviter la surchauffe.

2. Si le dispositif de control de température se déclenche, arrêtez l´appareil et laissez le refroidir.

Pendant ce temps, assurez-vous de déboucher les tuyaux et la brosse. Ainsi que les filtres.

3. Après 30mins, rebranchez l´appareil et reprenez l´utilisation.

1. Ne jamais manipuler l´appareil sans débrancher l´appareil

au préalable.

2. Videz le réservoir régulièrement.

3. Ne jamais nettoyer l´appareil avec des produits abrasifs.

Instructions d´Utilisation

Maintenance of the Cleaner

Image (5)

La page est en cours de chargement...

H Koenig AXO940 Manuel utilisateur

H Koenig AXO940 Manuel utilisateur

dans d''autres langues

Autres documents